L

L

L

Model AF95 -Continued Page 3

AF95 Constant Torque Specification Sheet

Output Ratings Horsepower Frequency Range Overload Rating Frequency Resolution

Frequency Accuracy

15-1OOHp ito133tfz 150% current for 1 minute 0.1% with digital input;

0.25% with analog input 0.05% of set point

Motor Performance Constant Torque Loads Speed Regulation

Standard 0.5% steady state via Slip

Compensation feature

Voltage at 60 Hz t2 Hz Displacement Power Factor

480 V *I 0% Better than 0.95 Tvoicallv areater than 97%

Design Type Converter Type lnverter Type

Waveform

Environment Operating Temperature

Chassis, NEMA 1 or 12 St;;i;;emperature

Maximum Elevation

Diode/Semi-conductor IGBT (Insulated Gate

Bipolar Transistor) Sine coded PWM

0” to 40°C. standard; 0” to 5O”C, refer to factory

-20” to 70°C 95% non-condensing 1OOOm (3300 ft)

Codes and Standards NEMA

z UL CUL

Enclosures Standard Optional

Designed Designed Designed Designed Designed

Chassis NEMA 1, Oversize NEMA 1,

NEMA 12 or MCC Mount

Protective Features AC Line Transients Circuit Breaker Input Line Reactors Ground Fault Protection Input Line Fuses

Motor Overload Protection

Output Contactor Output Short Protection

Overcurrent Overtemperature Overvoltage Phase Loss Protection Ride-thru Capability Undervoltage Motor Dv/Dt Protection

RFI I EMI Filters

MOV Protection Optional Optional 1.3 or 5% Electronic Protection Optional,

200,000 Amp Asymmetrical Electronic,

Motor Thermal Protection Optional Electronic Protection to

528 V Input Standard Standard Standard Standard

~~~~~:~ Optional,

1500 Wpsec or 1000 V/psec Optional

Set Up Adjustments, Performance Features, Operator Control and External Interface .

Keypad Alphanumeric,Display D$it;l$dicatlons

:;aqduency

Motor Voltage Motor Current Kilowatt Hours Program Parameters

Diagnostics

LED Status Indicators Keypad/Remote

Operator Functions

Standard, 2 x 16 character

RPM, % Speed, Hz or user defined units

HZ Percent Volts

iz Up to 50 parameters displayed

per Keypad Multi character alphanumeric

display with time and date stamp of faults

Terminal and Keypad Display Se

E arate Start/Stop and Speed ontrol Selection

Start/Stop, Speed Control, Jog and Forward/Reverse

I/O Terminal Block Digital Outputs Digital Inputs

Analog Outputs Analog Inputs

Programmable Parameters Accel and Decel

Linear and S-Curve Auto/Manual Auto Restart

After Power Interruption After Fault

Batch Mode

Carrier Frequency

Communications Interface

Current Limit

2 Form C relays, Standard 8 programmable,

2-24V dc ratin 2 outputs, O-10 $ dc or 4-20 mA 1 potentiometer, 1 follower

2 separately adjustable, rate adjustable (.3 to 1000 set)

Terminal input

Selectable Selectable, up to 15 attempts 16 batches, 16 parameters in

each batch Adjustable from 3 to 12 kHz

6 kHz from factory) d P programmer/diagnostics port with software, Standard

Ad,i,u;t;able to 150% rated

Programmable Parameters (Continued) DC Braking Standard Dwell Time Adjustable External Fault Terminal Input Jog 2 Independent Speeds, Jump Frequency 5 selectable with adjustable

high and low points Parameter Security 2 levels of password protection Preset Speeds Up to 32 preset speeds PID Controller PID process control Fault Reset Automatic or Manual Reversin

81 Keypad or Remote (Terminal)

Rotating otor Start Speed Setting

Standard (bidirectional)

Start and Stop Stop Modes

~~~~~~~~~~al

Volta B

e Boost Adjustable Volts Hertz Profiles Factory and Custom Profiles Dlgital Potentiometer Increase/Decrease speed

contacts

Reliability Pretested Components Surface mount technology on

printed circuit boards Printed Circuit Board

Thermal Stress Cycle Computerized Testing Final Test includes burn in with

motor under load Factory employed Field Service

Engineers

Maintainability Alphanumeric Displays

Logic Board Self Test Flash Programmed

Diagnostic Software

Standard Standard

Standard

Standard Standard

National network of AF drives specialists

Drive status and diagnostic information available on keypad displays

Standard Updates downloaded from an

standard IBM compatible P E Windows based configuration

software for advanced programming and troubleshootin

Model AF95 - Continued Page 4

Enclosure Dimensions

CT Hp

15

Chassis NEMA 1 NEMA 1 Oversize

NEMA 12 Llmited Option

NEMA 12 Full Option

‘2: 13.5 x 26 x 7.5 13.5 x28x8 26x32x11.8

30

:: 14x40x7.5 14x445~8 26 x 55 x 14.3

!! 14X46.5X7.5 14x51~8 26 x 77 x 14.3 IJ I I I I

100 14 x 54 x 7.5 14x60~8 26 x 77 x 14.3 91.5 x 40 x 21

Enclosure Type Available Options

cNz% Choice of either input line fuses (Cl Choice of either input line fuses (Cl , 1% input line reactor L , or output dV/dt filter L7 or LB). I’

1% input line reactor L I I’

or output dV/dt filter L7 or LB). I

NEMA 1 Oversize NEMA 12 Limited Option

All options listed are available in this configuration. Any combination of input disconnect (C). input fuses (Cl). output contactor (D). Manual l-O-8 bypass (l3), and/or auto transfer

I-O-B bypass (X3). NEMA 12 Full Option All Options listed are available in this configuration.

All of the above can also house all of the control options: 3 - 15 psig (M), Isolated process follower (M6), 120V interface (Ml5 or M5), and discrete contact expansion board (Y6 or Y7).

To build a catalog number for order entry, select a base catalog number from page 1 and add option suffixes

5A N 0

---1 C 015 V ABCD

- Modification codes

Application rating: V = Variable torque C = Constant torque

Horsepower: 015=15Hp

Voltage: C = 48OV, 60 Hz

Special

Base Catalog Number

Factory Mount Options

l Modification enclosure (NEMA 1 Oversize or

NEMA lZ)(G or D) l AC input disconnect(C) l Input line fuse (Cl) l AC output contactor (D) l 1%. 3% or 5% input line reactor (L, Li, l2) l EMllRFl filter (L9) l 1000 V/ms dV/dt or 1500 V/us dV/dt output filter

(L7 or L6) l Dynamic braking package (Wl) l Single overload relay or dual overload relays

(Y4 or Y5) l Custom nameplate (plastic or steel)(Nl or N2)

l Space heater with thermostat (V2) l Manual I-O-B bypass controller (13) l Auto transfer I-O-B bypass controller (X3) l 3 - 15 psig follower board (M) l Isolated process follower board (M6)

1 analog input; 4-20 mA or 0-IOV dc

2 analog outputs, selectable as 4-20 mA or 0-IOV dc l 120 volt control interface board - 8 channels (M15) l 120 volt control interface board - 4 channels (M5) l Discrete contact expansion board (Y6)

3 Form C relays rated 5 A at 240 volt resistive l Dual Discrete contact expansion board (Y7)

6 Form C relays rated 5 A at 240 volt resistive

l Floor stands (Vl)

Cutler-Hammer 110 Douglas Road, P.O. Box 819 Oldsmar. Florida 34677

SA-392 File Number 6600 October 1996 Printed in U.S.A.