MODEL 2070 › wp-content › uploads › ...MODEL 2070 OPERATION AND MAINTENANCE MANUAL 877 1st. AVE. NW Sioux Center, IA. 51250 Iowa 1-712-722-1488 . TAKE NOTE! THIS SAFETY ALERT

www.siouxautomation.com MON600138 7/5/05 $15

MaxiMixer MODEL 2070

OPERATION AND MAINTENANCE MANUAL

877 1st. AVE. NW Sioux Center, IA. 51250 Iowa 1-712-722-1488

TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.

THIS SYMBOL MEANS

- ATTENTION! - BECOME ALERT!

- YOUR SAFETY IS INVOLVED! SIGNAL WORDS:

Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate Signal word for each has been selected using the following guidelines: DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations typically for machine components that cannot be guarded for functional purposes.

WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices. CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

If you have any questions not answered in this manual or require additional copies or the manual is damaged, please contact your dealer or Sioux Automation Center, Inc., 877 1st Avenue N.W., Sioux Center, IA, 51250. (Telephone) 712-722-3711, (Fax) 712-722-3706.

SAFETY ALERT SYMBOL

− THE SAFETY ALERT SYMBOL IS USED TO PINPOINT CHARACTERISTICS WHICH IF NOT PROPERLY FOLLOWED CAN CREATE A SAFETY HAZARD.

− WHEN YOU SEE THIS SYMBOL IN THIS MANUAL OR ON

THE UNIT ITSELF, YOU ARE REMINDED TO:

BE ALERT! YOUR PERSONAL SAFETY IS INVOLVED!

SAFETY FIRST

FARM AND INDUSTRIAL EQUIPMENT INSTITUTE SAFETY ALERT SYMBOL. This symbol is used preceding all CAUTION (a general safety reminder), WARNING (denotes a potential hazard), and DANGER (denotes a potential injury) notices! Most farm accidents, like industrial, home, and highway accidents are caused by the failure of some individuals to observe simple and fundamental safety rules or precautions. For this reason, farm accidents, just as other types of accidents, can be prevented by recognising the causes of accidents and doing something about them before an accident occurs. Regardless of the care used in the design and construction of farm equipment, there are many points that cannot be completely safeguarded without interfering with accessibility and efficient operation. A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST AN ACCIDENT The complete observance of one simple rule would prevent many thousand serious injuries each year. That rule is "NEVER ATTEMPT TO CLEAN, OIL, OR ADJUST A MACHINE WHILE IN MOTION".

NATIONAL SAFETY COUNCIL

BEFORE ATTEMPTING TO OPERATE YOUR NEW MACHINE, BE SURE TO READ THIS OWNERS MANUAL AND FAMILIARIZE YOURSELF WITH THE MACHINE!! OBSERVE THE FOLLOWING PRECAUTIONS FOR SAFE OPERATIONS OF THIS MACHINE!!

SAFETY TIPS:

1. Keep Hands, Feet, and Clothing away from PTO Shaft! 2. DO NOT Climb on or enter Machine while in operation. 3. DO NOT Make High Speed Maneuvers with the machine. 4. Disengage PTO and remove Keys before servicing. 5. Keep ALL Shields in place. 6. DO NOT allow riders on outside of vehicle. 7. DO NOT attempt to clean, oil or adjust machine while in motion. 8. DO NOT exceed rated PTO RPM speed.

TABLE OF CONTENTS PAGE INTRODUCTION 2 SET-UP 3 - 4 OPERATION 5 -7 MAINTENANCE 8 - 9 Chains Hydrostat Drive Augers LUBRICATION SCHEDULE MON600139 DECAL LOCATIONS MON600140 ASSEMBLY PRINTS FINAL ASSEMBLY MON900462 BASE ASSEMBLY MON900454 TOP AUGER ASSEMBLY MON900455 BOTTOM AUGER ASSEMBLY MON900463 23” CHAIN TIGHTENER ASSEMBLY MON900422 8” CHAIN TIGHTENER ASSEMBLY MON900458 SHEAR SPROCKET ASSEMBLY MON900395 120 MM BEARING ASSEMBLY MON900377 140 MM BEARING ASSEMBLY MON900456 HYDROSTATIC DRIVELINE MON900470 HYDROSTATIC ASSEMBLY MON900465 & MON900465-1 HYDRAULIC ASSEMBLY MON900466 & MON900466-1 GEARBOX COOLER ASSEMBLY MON800366 JOYSTICK/HYDRO ASSEMBLY MON900419 JOYSTICK ASSEMBLY/SCHEMATIC MON900414 2” CYLINDER ASSEMBLY MON100437 DISCHARGE ASSEMBLIES MON600100

4052 MON900340, MON900364 MON900457

4062 MON900341, MON900361 MON900459

4074 MON900342, MON900362 MON900460

4080 MON900343, MON900363 MON900461

DRIVE ASSEMBLY MON700231 DRIVE COUPLING ASSEMBLY MON700143 FLIP CHUTE CYLINDER ASSEMBLY MON700230 FLIP CHUTE ASSEMBLY MON900335

LIGHT ASSEMBLY MON900467 & MON900467-1 TRUCK MOUNT C BAR ASSEMBLY MON900173 GENERAL SPECIFICATIONS

2

INTRODUCTION

Thank you for purchasing a 2070 MaxiMixer. The purpose of the MaxiMixer is to

give the agricultural industry the ability to incorporate long stem roughage into the total mixed ration

without additional grinders or processors. We have built the MaxiMixer to very exacting

standards and a high level of quality that will give you many years of dependable service if properly

used, maintained and serviced.

Along with the purchase of your new MaxiMixer you have also become part of a fine

family of agricultural equipment, and a fully equipped and knowledgeable service staff that can help

you with all your needs.

In addition to reading and completely understanding this owner's manual, please take the

time to fill out the warranty registration sheet so that we may process your warranty, as well as

anticipate your future needs.

MODEL NO: 2070 SERIAL NO__________________ DATE:_____________

Please have these ready when phoning in for service.

Sioux Automation Center Inc. 877 1ST AVE NW SIOUX CENTER IA 51250 (712) 722-1488

3

www.siouxautomation.com

USING YOUR MaxiMixer

READ CAREFULLY

SETUP 1. When you are delivered your new MaxiMixer from the factory, it is not immediately necessary

to check the machine for bearing lubrication or chain tightness, as these items have been factory serviced. It is recommended to walk around the machine and familiarize yourself with the location of all moving parts, caution decals, the general operating dimensions, and the basic working features of the MaxiMixer.

CAUTION! BEFORE OPERATING THIS MACHINE, READ AND UNDERSTAND THIS OWNER'S MANUAL AND ALL CAUTION, WARNING, AND DANGER SYMBOLS LOCATED ON THE MACHINE AND IN THIS MANUAL.

2. All lubrication has been completed at the factory prior to delivery and will not be immediately

necessary. For Lubrication intervals and specifications see the enclosed Lubrication Schedule.

IMPORTANT! DO NOT OVER GREASE BEARINGS, SEAL FAILURE AND SUBSEQUENT PREMATURE BEARING FAILURE COULD RESULT.

3. When you receive your MaxiMixer, it will be first necessary for you to hook up the power

source for the solenoid that switches power between the hydraulic functions (if so equipped). The switch box is supplied with a lead that has 1 white wire and 1 black wire. The white wire is to be hooked to positive and the black is to be hooked to ground. It is recommended to hook these leads into a switched power source such as a keyed ignition. This will eliminate the possibility of draining the battery if the switch is left on. When not in use, be sure to turn unit off. IMPORTANT: ALWAYS KEEP POWER CONNECTIONS TIGHT, NEAT AND FREE FROM DIRT AND CORROSION! DO NOT HOOK THE LEADS FOR THE SWITCH BOX INTO THE MIXER MOUNTED BATTERY THAT SUPPLIES THE SCALE! The leads for the switch box have been supplied with and inline fuse holder that holds a 10 amp fuse.

CAUTION! DO NOT REPLACE A BLOWN FUSE WITH A FUSE OF A HIGHER RATING!

4

4. The MaxiMixer has also been supplied to you with a complete scale system. Read and

understand the scale manual and familiarize yourself with its different functions. The scale indicator needs to be connected to a power source. Connect the scale indicators power cord directly to the solenoid operated hydraulic valve (if so equipped) or to the battery either on the mixer or the tractor. The leads are supplied with 1 white wire and 1 black wire. The white wire is to be connected to the positive and the black is to be connected to the ground. By having the scale connected to a constant power source, it will save warm up time between feedings. It is recommended to run the scale wires separately from other power lines to keep electrical interference to a minimum. A 10 amp inline fuse also protects the scale indicator. IMPORTANT! ALWAYS DISCONNECT SCALE LEADS BEFORE PERFORMING ANY SERVICE WORK SUCH AS WELDING!

5

OPERATION 1. Before attempting to fill the mixer, make sure that the discharge door is completely closed, the

chute is in the up position, and the mixing chamber is free of any foreign objects.

IMPORTANT! IF THE DISCHARGE DOOR IS LEFT OPEN DURING MIXING, FEED MAY BECOME TIGHTLY PLUGGED AGAINST THE CONVEYOR AND DAMAGE IT.

2. Refer to the Owner's Manual of the truck before operating the mixer, to ensure proper PTO engagement.

CAUTION: Avoid high speed engagement of the MaxiMixer as it could cause the shear pin to shear or damage the drive system.

3. The MaxiMixer will effectively mix all ingredients in a Total Mixed Ration

including small grains, corn, concentrates and premixes, cotton seed, corn and hay silage etc. The MaxiMixer is also capable of processing dry long stem hay into your ration. It is not recommended that wrapped and ensiled round bales be processed in the MaxiMixer.

IMPORTANT! THE MIXER SHOULD ALWAYS STAND LEVEL WHEN MIXING! 4. Due to the nature of mixing and cutting long stem hay, pin shearing is something that can be

expected. The shear pin is designed to be the weakest link in the drive train and its shearing is to prevent damage to critical components. Therefore never replace shear pins with a higher tensile strength or grade pin. If a machine is regularly shearing pins, the operator should first look for mechanical problems such as worn knives or a bearing failure, then evaluate loading procedures and lastly, call for technical assistance.

DANGER! TO PREVENT SERIOUS INJURY OR DEATH, DO NOT ENTER THE MIXING CHAMBER!

6

5. Proper loading procedure involves loading smaller quantity ingredients in the center of the mixer first, to cover up the mixing paddles. This will prevent the aggressive paddles from grabbing too much hay before it can be first adequately processed by the knives on the auger flighting. Loading long stem hay in the center of the mixer increases the chances of shearing pins. If not happy with the resulting ration, some sequencing changes may need to be made. If sequencing changes do not fix your ration problems, see the factory for further assistance. Do not be concerned about the appearance of the ration in the mixer; the appearance and evenness of the ration is determined only in the bunk.

6. To discharge feed from the MaxiMixer it is necessary to first start the conveyor (either self

contained hydraulics, or tractor supplied) and then open the discharge door. The conveyor and the door operate on two different hydraulic circuits and can be operated independently. The rate of ration flowing from the MaxiMixer can be controlled by the door position. The higher the door is raised, the more feed it will allow out, and vice versa.

IMPORTANT! ALWAYS START THE DISCHARGE BEFORE OPENING THE DOOR TO PREVENT JAMMING FEED AGAINST THE CONVEYOR!

SMALL INGREDIENTS

HAY HAY

7

7. Normal mixing time is from 1 to 2 minutes after the last ingredient has been added. It is necessary to run the MaxiMixer at 1800 ENGINE RPM during mixing of ingredients such as long stem hay or ensilage. It is not necessary to run the machine while loading. Strive for the shortest mixing time possible, as over-mixing will decrease the value of the ration and will cause unnecessary wear on the machine.

8. Proper mixing patterns are achieved when two cavities are visible in the mixer, one in the front

and one in the rear. Feed must be able to tumble from the top to the bottom of the mixer to obtain maximum mixing potential. A mixer that is struck level full will not mix properly and will put undue stress on moving parts.

9. Do not leave partially mixed loads in the machine for long periods of time such as during the day

or overnight. Acids from the feed will react with the steel and will cause premature deterioration of the machine. It is better to mix two small loads, than one large load.

8

MAINTENANCE Your MaxiMixer will be delivered, fully lubricated and set up to all drive component installation specifications. During the break in of your new MaxiMixer, it is recommended that a complete daily inspection of all drive components be carried out. Throughout the life of your Maximixer, a complete inspection of all drive components, fasteners, auger knives and shields should be carried out during scheduled lubrication times. Wore or damaged parts must be replaced, loose or misaligned parts must be adjusted and tightened to assure proper operation and life of components.

WARNING: Always shut off engine, set parking brake, remove the key and wait for all motion to stop before attempting to adjust, lubricate, service or setup this machine!

CHAINS Discharge Conveyor Chain A. The conveyor chain will loosen up some during the first few hours of operation and over the

life of the discharge. Lift a flight near the center of the table. It should move about an inch off the floor. Remember when tightening the chain to move both take ups the same distance so the conveyor chain runs straight along the length of the discharge.

Oil bath Roller Chain and Sprockets Chain Tension B. Be sure it is tensioned adequately to prevent tooth jumping (ratcheting) under the most

severe load conditions, which the drive will encounter during operation. C. Adjust spring tightener, to eliminate any slack in roller chain, by moving turn buckle along

tightening chain to increase tension on spring. Drive Alignment D. Any degree of sprocket misalignment will result in some reduction of chain life.

Misalignment of all roller chain sprocket drives should not exceed 1/4 degree or 1/16” per foot of linear distance. Misalignment should be checked with a good, straight edge tool. The tool should be applied from the driver to driven, and then from the driven to driver sprockets so that the total effect of parallel and angular misalignment is taken into account.

E. Drive misalignment can cause premature sprocket and chain wear. Extreme case may result binding of chain and drive failure. Alignment of sprockets, using shims and the adjusting

9

screw on the jackshaft, is critical for proper operation of your MaxiMixer. Upper Auger Shear Sprocket F. The shear sprocket uses two 5/8 X 3-1/2” NC grade 5 bolts. Any change from this

specification will void warranty. HYDROSTATIC DRIVE G. Be sure to keep universal joints greased in PTO shaft, which is located between engine crank

and Hydrostat Pump. H. Maintain proper level of hydraulic oil in reservoir. Oil level must be two inches below fill

cap or visible in site gauge (if equipped) located on exterior of oil reservoir. Recommended oil is JOHN-DEERE HY-GARD, CASE HY-TRAN, OR DEUTZ ALLIS POWER FLUID 821.

I. Check and clean oil cooler radiator often. Ensures proper oil temperature, and longer life of components.

J. Change Oil filter on recommended service interval, or if your machine is equipped with a gauge on filter housing change when indicated so.

K. Visually inspect high pressure hydraulic lines often, looking for leaks, cracks, or wear marks. Replace immediately any damaged hoses. When inspecting machine turn off all power and wait till all parts have stopped moving.

HIGH PRESSURE OIL KILLS L. Change oil in Final Drive Gearbox at recommended intervals. Replace with Synthetic 90

WT oil. AUGERS Knives M. Auger Knives should be checked regularly for lose or damaged knives and tightened or

replaced as required. A minimum of grade 5 carriage bolts and lock nuts should be used because of wear.

N. Rotating knives from high wear areas (middle of auger) to low wear areas (end of auger) will increase the life of the knife set and maintain a high level of cutting action. Knifes wore past the tungsten coating and are not effective for cutting should be replaced. Knifes should be set as close as possible to stainless steel bars on the belly, but must not hit.

Bushings O. Both augers run on oil impregnated nylon bushings at the front of the mixer. This assembly is

designed to make a metal rubbing metal squealing sound when bushing is wore and needs replacement. Prolong use at this stage, without replacing bushing, will cause damage to both the stub shaft and auger sleeve.

P. To change the bushing: - support the auger in the mixer

10

- remove the stub shaft from the front of the mixer - remove the wore bushing from the auger sleeve - tap new bushing into auger sleeve using wooden block - grease stub shaft and reinstall - remove auger support and any foreign objects from inside mixer

WARNINGIF WORK MUST BE PREFORMED INSIDEMIXER A PROTECTIVE COVER MUST BEPLACED OVER KNIVES TO AVOID INJUSRYOR DEATH.

ALWAYS STOP MIXER AND TURN OFF MOTOR BEFORE LUBRICATION,ADJUSTINGOR SERVICING THIS MACHINE.

SERVICE NOTES:

ALL BEARINGS, SHAFTS, SPROCKETS, CHAINS, BELTS AND FASTENERSMUST BE VISUALLY INSPECTED, WHEN LUBRICATING MIXER.

WORE OR DAMAGED PARTS MUST BE REPLACED

LOOSE OR MISALIGNED PARTS MUST BE ADJUSTED AND TIGHTENEDTO ASSURE PROPER OPERATION AND LIFE OF COMPONENTS.

REVISIONSECN REV. DESCRIPTION DATE BY CK

SIOUX AUTOMATION CENTER INC.877 FIRST AVE NW SIOUX CENTER, IA 51250

REVDWG NO.SIZE

B

CMDATE

06-05

4:1

AS NOTED MON600139 -2070,TRKMNT,192,SCHED,LUB

SHEET OF 1

D

C

B

A

B

C

D

12345678

8

PROPERTY OF

.03 X 45

7

MATERIAL

TOLERENCES UNLESS SPECIFIED

.020 ANGULAR

BREAK ALL EDGES

1

6 5 4 3 2 1REV -DWG NO. MON600139

DO NOT SCALE DRAWING

DRAWN

DATECHECKED

SCALE

FRACTIONAL 1/32 3 PLACE .0052 PLACE

DIMENSIONS ARE IN INCHES

1

2

1

5

56

3

4

37

POINT ITEM LUBRICATION INTERVAL

1 OILBATH DRIVE CHAIN LIGHT WEIGHT OILCHECK OVERY 40 HOURS OF

OPERATION CHANGE YEARLY

2 DRIVELINE SHAFTSTANDARD ALL PURPOSE

GUN GREASEEVERY 40 HOURS OF

OPERATION

3 ALL DRIVE BEARINGSSTANDARD ALL PURPOSE


OPERATION

4FRONT AUGER

BUSHINGSTANDARD ALL PURPOSE


OPERATION

5DISHCARGE BEARINGS

STANDARD ALL PURPOSE GUN GREASE

EVERY 40 HOURS OF OPERATION

6 DISCHARGE CHAIN LIGHT WEIGHT OILBRUSH ON LIGHTLY EVERY 40

HOURS OF OPERATION

7 PLANENTARYSYNTHETIC GEAR LUBE

OILEVERY 40 HOURS OF

OPERATION (CHECK ONLY)

1

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV -DWG NO. MON600140


DRAWN

DATECHECKED

SCALE

OF

.03 X 45BREAK ALL EDGES

SHEET

2070,TRKMNT,192,DECAL,LOCATION

-MON600140 1 .020 ANGULAR


MATERIAL

PROPERTY OFSIOUX AUTOMATION CENTER INC.877 FIRST AVE NW SIOUX CENTER, IA 51250

REVDWG NO.SIZE

B

CMDATE

06-05

1:40

AS NOTED



1

1

5

1

8

72

4

6

3

1

10 11

5

1

1

5

5

879

11

REVISIONSECN REV. DESCRIPTION DATE BY CHK

ITEM # QTY. PART # DESCRIPTION1 6 DEC102 DECAL,GRS,GUN,PICTURE2 1 DEC106 DECAL,CAUTION,MAN,OWNER,5,63 1 DEC108 DECAL,WARNING,PART,MOVING,4,44 1 DEC109 DECAL,CAUTION,WLD,3,35 4 DEC111 DECAL,DANGER,AUGER,5,66 1 DEC114 DECAL,MONO,GA,DOOR7 2 DEC128 DECAL,SAC,LOGO,NEW,3,5.668 2 DEC154 DECAL,SAC,LOGO,NEW,20.5H,24W9 1 DEC158 DECAL,MAXI,6,108,RH10 1 DEC159 DECAL,MAXI,6,108,LH11 2 DEC219 DECAL,MAXI,2070,BLACK

MaxiMixer Model 2070 Truck Mount

Assembly Prints


ITEM # QTY PART # DESCRIPTION

1 16 BLT12X2NCG8 BLT,HEX,1/2,2,NC,G82 16 BLT38X1NC BLT,HEX,3/8,1,NC,G53 2 BLT38X712NC BLT,HEX,3/8,7-1/2,NC,G54 8 BLT516X114NC BLT,HEX,5/16,1-1/4,NC,G55 32 BLT58X212NC BLT58X212NC6 1 MON100321 ROD,LIFT,DIS,407 2 MON100908 WRM38TEPIPE,6.128 2 MON101667 WRM5CHANNEL,13.319 2 MON101668 SUPPORT,BUMPER,TRK,RR,2070

10 1 MON101669 HOOD,PUMP,HYDRO,207011 1 MON600100 DIS,ROLLER,OPTIONS12 1 MON700624 MOUNT,BODY,TRK,209013 1 MON700625 MOUNT,BODY,TRK,WEDGE,9.3814 1 MON700732 LADDER,16,48.7515 1 MON700733 MOUNT,BODY,TRK,RR,207016 1 MON700734 MOUNT,BODY,TRK,WEDGE,5.8417 1 MON800366 COOLER,OIL,HYDDRVN,5KW18 2 MON900397 TANK,HYD,30GAL,209019 1 MON900454 2070,TRK,BASE,ASSY20 1 MON900465 HYDRO,2070,ASSY21 1 MON900466 HYD,AUX,207022 1 MON900467 LIGHT,TRK,2070,ASSY23 16 NUT12NCG8 NUT,HEX,1/2,NC,G824 2 NUT38LOCKNC NUT,LOCK,3/8,NC,G525 12 NUT38NC NUT,HEX,3/8,NC,G526 4 NUT38WING NUT,WING,3/827 8 NUT516NC NUT,HEX,5/16,NC,G528 32 NUT58NC NUT,HEX,5/8,NC,G529 1 SAC35333 BUMPER,TRK,RR,83080430 2 SAC56009 STRAP,FLAT,MUD31 1 SAC60738 FENDER,TRK,POLY,TANDEM,KIT32 1 SAC75836 SCALE,KIT,KNIGHT,BOTEC,TRUCK33 1 SACFLAP24X36 FLAP,MUD,.38,24,3634 4 SCA170031 MOUNT,LDCLL,ASSY35 50 SPCABLETIEHVY TIE,CABLE,HVY,#17536 100 SPCABLETIEMED TIE,CABLE,MED,#30-5037 2 SPCP316X2 PIN,COTTER,3/16,238 1 TRKFRAMETANDOM TRK,134 CAB TO FRONT AXLE39 16 WSH12LOCKG8 WSH,LOCK,1/2,G840 16 WSH38LOCK WSH,LOCK,3/841 8 WSH516LOCK WSH,LOCK,5/1642 32 WSH58LOCK WSH,LOCK,5/8

4

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV ZZDWG NO. MON900462


DRAWN

DATECHECKED

SCALE

OF


SHEET

2070,TRK,FINAL,ASSY

ZZMON900462 1 .020 ANGULAR


MATERIAL


REVDWG NO.SIZE

B

CMDATE

05-04

1:35

AS NOTED



1

24.66 109.34

180.88

161.00

C L MOUNT C

L MOUNT

3033

13

121 39 23

1516

9

8 29

9

13923

38

44127SEE NOTE #2

SEE NOTE #3

SEE NOTE #4

CHASSIS DIM'S.

NOTES:1.) FRONT FRAME EXTENSION MUST ALLOW FOR 3.00 CLEARANCE BETWEEN FRONT OF PUMPS AND EXTENDED BUMPER.2.) DRILL HOLES IN TRUCK FRAME TO SUIT FOR FOR MOUNTING FENDERS AND MIXER MOUNTS.3.) CUT MUDFLAPS TO 24" LENGTHS. USE SCRAP TO MAKE MON\101419 & MON\101420.4.) THE EXTENDED FRONT BUMPER AND HYDRO PUMP MOUNT TO BE MANUFACTURED TO TRUCK REQUIREMENTS.

209.50

134.00SEE NOTE #121.00

54.00

13.50.25

TYP.ALL REAR BUMPERCOMPONENTS

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV ZZDWG NO. MON900462


DRAWN

DATECHECKED

SCALE BREAK ALL EDGES.03 X 45

FRACTIONAL 1/32 3 PLACE .0052 PLACE .020 ANGULAR 1

DIMENSIONS ARE IN INCHESTOLERENCES UNLESS SPECIFIED

MATERIAL


REVDWG NO.SIZE

B

CMDATE

05-04

1:55

AS NOTED MON900462 ZZ2070,TRK,FINAL,ASSY

SHEET OF 42

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV ZZDWG NO. MON900462


DRAWN

DATECHECKED




MATERIAL


REVDWG NO.SIZE

B

CMDATE

05-04

1:32


SHEET OF 43

19

14

22

637

11

3

7

24

2 40 25

5 42 28

2640210

DRILL HOLES IN TRUCK FRAME AS NEEDEDFOR PUMP HOOD & WELD HEADS OF BOLTS TO INSIDE OF FRAME.

34 SEE NOTE #1

NOTE:S:1.) LOAD CELL MOUNTS MUST ALL MOUNT WITH STABILIZER BARS AT 90 TO EACH OTHER. REAR LEFT AND FRONT RIGHT TO RUN FROM FRONT TO BACK. REAR RIGHT AND FRONT LEFT TO RUN FROM SIDE TO SIDE.

32

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV ZZDWG NO. MON900462


DRAWN

DATECHECKED




MATERIAL


REVDWG NO.SIZE

B

CMDATE

05-04

1:34


SHEET OF 44

20

18

24025

18


ITEM # QTY PART # DESCRIPTION1 15 BLT1X312NC BLT,HEX,1,312,NC,G52 3 BLT34X112NF BLT,HEX,3/4,1-1/2,NF,G83 4 BLT34X2NC BLT,HEX,3/4,2,NC,G54 6 BLT34X512NC BLT,HEX,3/4,5-1/2,NC,G55 6 BLT34X612NC BLT,HEX,3/4,6,NC,G56 18 BLT38X1NC BLT,HEX,3/8,1,NC,G57 12 BLT58X7NF BLT,HEX,5/8,7,NF,G88 4 BLT78X3NC BLT,HEX,7/8,3,NC,G59 1 BRGFB22464H BRG,FLG,4BLT,4

10 1 BURN12000305 DISK,4.5,.81,.511 1 FA001 TIE,SHIELD,RUBBER,W/BRKT12 3 HYDSC003 PIN,CYL,CLEVIS,1,313 1 MON100437 CYL,HYD,2,10,PAINTED14 2 MON100450 ARM,LINKAGE,DOOR15 1 MON100831 GA,DOOR,ROD,500,TRK16 1 MON101007 SPACER,RND,4.5,4.03,1.4717 1 MON101173 SPACER,RND,5.5,4.73,2.2518 4 MON101174 SPACER,RND,5.56,4.81,.0619 1 MON101175 DISK,6.25,.81,.520 3 MON101520 PIN,HINGE,SHIELD,2050,PLTRY21 1 MON101599 SPK,140,18,120mm,SPLINED22 1 MON101600 SPACER,RND,5.5,4.73,1.0623 1 MON101605 SPACER,RND,6.25,5.51,2.0624 4 MON101616 SPACER,RND,6.25,5.51,.0625 1 MON101617 DISK,7.75,.81,.526 1 MON101620 CHAIN,ROLLER,200-H,147.5,59P27 1 MON101623 CHAIN,ROLLER,140-H,141.75,81P28 1 MON101670 PLNTRY,BREVINI,3155,47.78,RED29 1 MON600138 MANUAL,MAXI,2070,TRK,19230 1 MON700013 DOOR,DIS,PIVOT,WLD,4031 1 MON700471 LEVER,ASSY,DOOR,TRK32 1 MON700635 SHAFT,FLG,5.5,10,8.75,TRK,PNT33 1 MON700714 BODY,2070,TRK,WLD34 1 MON700725 COUP,FLG,2070,TRK,WLD35 1 MON700726 SPK,200,50,140mm,WLD36 1 MON700727 SPK,200,11,105mm,SPLINED37 1 MON700731 SHIELD,RR,2070,WLD38 1 MON700758 PNL,OILBATH,RH,2070,WLD39 1 MON700759 BRKT,OILBATH,SHIELD,2070,WLD40 1 MON700760 SHIELD,FR,RH,TRK,2070,WLD41 1 MON700761 SHIELD,FR,LH,TRK,2070,WLD42 1 MON700762 PNL,OILBATH,LH,2070,WLD43 1 MON900377 BRG,FLG,6BLT,120mm,ASSY44 1 MON900395 SPK,140,38,4,SHEAR,ASSY45 1 MON900422 TIGHTNR,CHAIN,23,2050,ASSY46 1 MON900455 AUG,MAXI,2070,ASSY47 1 MON900456 BRG,FLG,6BLT,140mm,ASSY48 1 MON900458 TIGHTNR,CHAIN,200,8,ASSY49 1 MON900463 AUG,2070,BOT,ASSY50 3 NUT1032LOCK NUT,LOCK,1032,NYLON51 15 NUT1NC NUT,HEX,1,NC,G552 6 NUT34LOCKNC NUTLOCK34NC53 10 NUT34NC NUT,HEX,3/4,NC,G554 38 NUT38WING NUT,WING,3/8

ITEM # QTY PART # DESCRIPTION55 4 NUT78NC NUT,HEX,7/8,NC,G556 39 OILSHC630 OIL,GRLUB,SYNTH,MOBILE,SHC63057 500 OSW830848 WTHRSTRP,SEAL,DOOR58 1 PFBL112PLUG PLUG,1-1/2,BLK59 1 PFPL2PLUG PLUG,2,PL60 1 RC140HCON LINK,CONN,140H61 1 RC200HCON LINK,CONN,200H62 6 SPCP14X2 PIN,COTTER,1/4,263 3 SPCP18X1 PIN,COTTER,1/8,164 2 SPCP316X2 PIN,COTTER,3/16,265 1 SPGH36 HOSE,GRS,36,1/8NP66 2 SPGZRK610 ZRK,GRS,1/8,MALE,PIPE,STR67 1 SPGZRK613 ZRK,GRS,1/8,MALE,PIPE,90DEG68 1 SPGZRK618 ZRK,GREASE,1/8,FEM,PIPE,STR69 3 SPMB1032X34 BLT,MACH,10-32,3/470 2 SPPR316X12A RIVET,POP,3/16,1/2,ALUM71 56 STI700221 OIL,HYD,EXXON,UNIVIS,N,3272 6 WSH1FLAT WSH,FLAT,173 15 WSH1LOCK WSH,LOCK,174 19 WSH34LOCK WSH,LOCK,3/475 55 WSH38LOCK WSH,LOCK,3/876 38 WSH516FLAT WSH,FLAT,5/1677 2 WSH58FLAT WSH,FLAT,5/878 12 WSH58LOCKG8 WSH,LOCK,5/8,G879 4 WSH78LOCK WSH,LOCK,7/8

3

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV ZZDWG NO. MON900454


DRAWN

DATECHECKED

SCALE

OF


SHEET

2070,TRK,BASE,ASSY



MATERIAL


REVDWG NO.SIZE

B

CMDATE

05-04

1:50

AS NOTED



1

CUT LENGTH

OPER. W/C PC/HRDEPT CREWDESCRIPTION

RAW MAT.AREAPERIMETER

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV ZZDWG NO. MON900454


DRAWN

DATECHECKED




MATERIAL


REVDWG NO.SIZE

B

CMDATE

05-04

1:28

AS NOTED MON900454 ZZ2070,TRK,BASE,ASSY

SHEET OF 32

CUT LENGTH



5475

76

40

30

6262

72

14

31

1214

7262

6272

12

621215

13

7262

57 APPLY WEATHER STRIP ALLAROUND DOOR OPENING

58

59

33

3839

4142

675

37

63

20

7011

6950

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REV ZZDWG NO. MON900454


DRAWN

DATECHECKED




MATERIAL


REVDWG NO.SIZE

B

CMDATE

05-04

1:21

AS NOTED MON900454 ZZ2070,TRK,BASE,ASSY

SHEET OF 33

CUT LENGTH



8

79 55

16

10

74

2

45

64

27419

18

18

5374

17

4

21

276046

49

3

7453

3267

778

28

486477

2836

2661

2 74 2535

5274 5

24

23 4751 73

1

6568

24

SEE NOTE

SEE NOTE

NOTE:1.) SHIM AS REQUIRED TO ALLOW PROPER CHAIN ALIGNMENT2.) SHIM & TIGHTNEN REAR SPROCKET ASSY FIRST3.) SHIM FRONT SPROCKET TO ALLOW .03 FLOAT

SEE NOTE

966

4366

SEE NOTE

REVISIONS

ECN REV. DESCRIPTION DATE BY CHK

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVZZDWG NO.

MON900455


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF

SIOUX AUTOMATION CENTER INC.SIOUX AUTOMATION CENTER INC.SIOUX AUTOMATION CENTER INC.SIOUX AUTOMATION CENTER INC.877 FIRST AVE NW SIOUX CENTER, IA 51250877 FIRST AVE NW SIOUX CENTER, IA 51250877 FIRST AVE NW SIOUX CENTER, IA 51250877 FIRST AVE NW SIOUX CENTER, IA 51250

REVDWG NO.SIZE

B

CMDATE

03-04

1:15

AS NOTED MON900455 ZZ

AUG,MAXI,2070,ASSY

SHEET OF 11


RAW MAT.

AREA

CUT LENGTH

PERIMETER

IF WORK MUST BE PREFORMED INSIDEMIXER, A PROTECTIVE COVER MUSTBE PLACED OVER KNIVES TO AVOIDINJURY OR DEATH. ALWAYS STOP MIXER AND DISCONNECTPOWER BEFORE LUBRICATING, ADJUSTINGOR SERVICING THIS MACHINE. NOTE:ALL KNIVES TO BE ON PRODUCT FLOWSIDE OF FLIGHTING.

WARNING

1

2

FLIGHTING KNIFE DETAILTYP.LOCATIONS

SCALE 1 : 3

ITEM NO. QTY. PART NO. DESCRIPTION

1 1 MON700719 AUG,MAXI,2070,TOP,WLD

2 1 MON101005 BUSHING,PLNYOIL,5.5,6.25,6.13

3 20 MONP100171 KNIFE,AUGER,RH,TUNGSTEN,TIPPED

4 12 MONP100170 KNIFE,AUGER,LH,TUNGSTEN,TIPPED

5 64 BLT716X114CG5 BLT,CARR,7/16,114,NC,G5

6 64 NUT716LOCKNC NUT,LOCK,7/16,NC,G5

7 64 WSH716FLAT WSH,FLAT,7/16

IF WORK MUST BE PREFORMED INSIDEMIXER, A PROTECTIVE COVER MUSTBE PLACED OVER KNIVES TO AVOIDINJURY OR DEATH. ALWAYS STOP MIXER AND DISCONNECTPOWER BEFORE LUBRICATING, ADJUSTINGOR SERVICING THIS MACHINE. NOTE:ALL KNIVES TO BE ON PRODUCT FLOWSIDE OF FLIGHTING.

WARNING

1

2

FLIGHTING KNIFE DETAILTYP.LOCATIONS

SCALE 1 : 3


1 1 MON700719 AUG,MAXI,2070,TOP,WLD

2 1 MON101005 BUSHING,PLNYOIL,5.5,6.25,6.13






AUGER ROTATIONFROM REAR

3 4

6 7 5

AUGER ROTATIONFROM REAR

3 4

6 7 5

REVISIONS


ITEM # QTY. PART # DESCRIPTION


2 1 MON700724 AUG,2070,BOT,BLADE,WLD



5 21 MONP100172 KNIFE,AUGER,PADDLE,TUNGSTEN



8 129 WSH716LOCK WSH,LOCK,7/16

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVZZDWG NO.

MON900463


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

CMDATE

05-04

1:14


AUG,2070,BOT,ASSY

SHEET OF 11


RAW MAT.

AREA

CUT LENGTH

PERIMETER

8 6 7 1

5

3

4

2

IF WORK MUST BE PREFORMED INSIDEMIXER, A PROTECTIVE COVER MUSTBE PLACED OVER KNIVES TO AVOIDINJURY OR DEATH. ALWAYS STOP MIXER AND DISCONNECTPOWER BEFORE LUBRICATING, ADJUSTINGOR SERVICING THIS MACHINE. NOTE:ALL KNIVES TO BE ON PRODUCT FLOWSIDE OF BLADES AND PADDLES.

WARNING

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVISIONSREV. DATE CHKBYDESCRIPTIONECN

REV -DWG NO.

MON900422


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

CMDATE

08-03

1:4

AS SHOWN MON900422 -

TIGHTNR,CHAIN,23,2050,ASSY

SHEET OF 11

3

4

2

7

1

8

NOTE:1.) TENSION ON TIGHTENER SHOULD BE JUST ENOUGH TO PRODUCE SMOOTH TRAVEL OF CHAIN. OVER TIGHTENING WILL REDUCE TIGHTENER AND CHAIN LIFE.2.) TIGHTEN NUT AGAINST TURNBUCKLE AFTER PROPER TENSION ADJUSTMENT IS MADE.

SEE NOTE 2

5

5

9

9

6

7


1 1 MON700552 TIGHTNR,CHAIN,23

2 1 MON101036 TIGHTNR,NYL,CHAIN,120,140

3 1 OSW840253 SPRING,EXPNSN

4 1 SPEE38 TRNBCKL,3/8,EYE,EYE


6 1 BLT12X4NC BLT,HEX,1/2,4,NC,G5


8 1 NUT38NC NUT,HEX,3/8,NC,G5


1

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1


REVZZDWG NO.

MON900458


DRAWN

DATECHECKED

SCALE

OF


SHEET

TIGHTNR,CHAIN,200,8,ASSY



MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

CMDATE

04-04

1:4

AS SHOWN



1

6

5

7

2

1

7

3

3

SEE NOTE 2

TENSION ADJUSTMENT IS MADE.

NOTE:1.) TENSION ON TIGHTENER SHOULD BE JUST ENOUGH TO PRODUCE SMOOTH TRAVEL OF CHAIN. OVER TIGHTENING WILL REDUCE TIGHTENER AND CHAIN LIFE.2.) TIGHTEN NUT AGAINST TURNBUCKLE AFTER PROPER

4


1 1 MON700597 TIGHTNR,CHAIN,8

2 1 MON100932 TIGHTNR,NYL,CHAIN,100


4 1 BLT12X4NC BLT,HEX,1/2,4,NC,G5

5 1 OSW840253 SPRING,EXPNSN

6 1 SPEE38 TRNBCKL,3/8,EYE,EYE


SEE NOTE 2

NOTE:

1.) APPLY A THIN FILM OF GEASE BETWEEN THE SHEAR HUB AND SPROCKET AT ASSY.

2.) THE BRONZE BUSHING IS TO BE PRESS FIT INTO THE SPROCKET.

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1


REV DWG NO. MON900395DO NOT SCALE DRAWING

DRAWN

DATECHECKED




MATERIAL

PROPERTY OFSIOUX AUTOMATION CENTER INC.

877 FIRST AVE NW SIOUX CENTER, IA 51250

REVDWG NO.SIZE

B

JLDATE

04-01

1:4

AS SHOWN MON900395 SPK,140,38,4,SHEAR,ASSY

SHEET OF 11

61

7

2

3

4

5

SEE NOTE 1

ITEM NO. QTY. PART NO. DESCRIPTION1 1 MON700615 HUB,SHEAR,SPK,SPLINED,4,WLD2 1 MON101300 BRG,BUSHING,5.5,5,.92,BRZ3 1 MON101282 DISK,6.5,5.03,10GA4 1 KN172289 RING,SNAP,OUTSIDE,55 1 MON700616 SPK,140,A,38,5.5,SHEAR,WLD6 2 BLT58X312NC BLT,HEX,5/8,3-1/2,NC,G57 2 NUT58LOCKNC NUT,LOCK,5/8,NC,G5


1 1 BRG22224CJ BRG,ROLLER,120MM,215MM,SPHER

2 1 MON101142 HOUSING,BRG22224CJ

3 1 MON101143 CAP,BRG22224CJ

4 2 SELNA417254 SEAL,OIL,5.5,6,5,.56

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVISIONS

REV. DATE CHKBYDESCRIPTIONECN

REV -DWG NO.

MON900377


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

JLDATE

04-01

1:4

AS NOTED MON900377 -

BRG,FLG,6BLT,120mm,ASSY

SHEET OF 11

2

4

1

4

3

REVISIONS



1 1 BRG22228CJW33C3 BRG,ROLLER,140MM,250MM,SPHER

2 1 MON101606 HOUSING,BRG22228CJ

3 1 MON101634 CAP,BRG22228CJ

4 1 SELCR55120 SEAL,OIL,140mm,170mm,15mm

5 1 SELCR62495 SEAL,OIL,6.25,7.5,.56

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVZZDWG NO.

MON900456


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

CMDATE

03-04

1:4


BRG,FLG,6BLT,140mm,ASSY

SHEET OF 11


RAW MAT.

AREA

CUT LENGTH

PERIMETER

2

4

1

5

3


1 4 BLT14X12NC BLT,HEX,1/4,1/2,NC,G5

2 4 BLT14X34NC BLT,HEX,1/4,3/4,NC,G5

3 1 KN172947 CNTRL,LEVER,HYDRO,FAST,SLOW

4 1 MON700681 JBOX,HYDROSTAT,WLD

5 1 MON900414 JOYSTICK,MIXER,TRK,ASSY



REVISIONS

ECN REV. DESCRIPTION DATE BY CK

3570 ADEL: NUT14LOCKNC ADD: WSH14LOCK QTY 4 &

WSH14FLAT QTY 45/3/2005 CM

1

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVADWG NO.

MON900419


DRAWN

DATECHECKED

SCALE

OF


SHEET

JOYSTICK,MIXER,TRK,HYDRO,ASSY

AMON900419 1 .020 ANGULAR


MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

CVDATE

7-03

1:3

AS NOTED



1

5

3

4

1

2

7

6

ITEM # QTY. PART # DESCRIPTION1 4 BLT14X12FNC BLT,FLAT,1/4,1/2,NC,G52 4 BLT14X34NC BLT,HEX,1/4,3/4,NC,G53 1 MON101455 COVER,JBOX,JOYSTICK4 1 MON101462 DECAL,FACE,JOYSTICK5 1 MON700672 JBOX,JOYSTICK,WLD6 1 MON700692 CABLE,POWER,4PIN,10'7 1 MON800351 JOYSTICK,MIXER,TRK

8 4 NUT1032LOCK NUT,LOCK,1032,NYLON

9 4 NUT14NC NUT,HEX,1/4,NC,G510 8 NUT440 NUT,HEX,4-40

11 1 SCA2060611 CONN,RCPTL,AMP,11-412 1 SCA2067051 CONN,RCPTCL,AMP,STD,13-913 13 SCA661034 CONTACT,PIN,AMP,GOLD,18-1614 4 SPMB1032X12 BLT,MACH,10-32,1/214 8 SPMB440X12 BLT,MACH,4-40,1/216 4 WSH14LOCK WSH,LOCK,1/4

7

4

3

2

16

5

19

07-04D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1


REVCDWG NO.

MON900414


DRAWN

DATECHECKED

SCALE

CM


& NUT440(QTY8)

ADD: SPMB1032X12(QTY 4), NUT1032(QTY 4),

3024

2637

1 .020 ANGULAR


MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

APDATE

04-03

1:2

AS NOTED MON900414 C

JOYSTICK,MIXER,TRK,ASSY

SHEET OF 21

ECN ADDED SCA2067051 & SCA2060611 CV8-03A

B 2-04 CV


SCA661034(QTY 13) DEL: SCA660994 (QTY 13)


ADD: BLT14X12FNC(QTY 4),NUT14NC(QTY 4),C

148

1410

2

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVISIONS


REVCDWG NO.

MON900414


DRAWN

DATECHECKED

SCALE

OF


SHEET

JOYSTICK,MIXER,TRK,ASSY

CMON900414 1 .020 ANGULAR


MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

APDATE

04-03

1:1

AS NOTED



2

CON1,PIN 7 (PURPLE) TO PIN #4CON5,PIN 7 (W/BRN) TO PIN #3

CON5,PIN 4 (W/BLK) TO PIN #5CON1,PIN 5 (BLACK) TO PIN #6

CON1,PIN 9 (BLUE) TO PIN #9CON5,PIN 6 (W/RED) TO PIN #8CON1,PIN 11 (GRAY) TO PIN #7

CON1,PIN 6 (BROWN) TO PIN #1

(CON5,PIN 2 (RED) TO PIN #1CON5,PIN 1 (YELLOW) TO PIN #2

CON1,PIN 2 (GREEN) TO PIN #3CON5,PIN 8 (W/ORG) TO PIN #4

CON5,PIN 3 (WHITE) TO PIN #2

FROM JOYSTICK BOARD

BOTTOM JOYSTICK BOX

2

1

3

4

1

4

2

5

3

6

7 8 9

6

7

8

8

10

10

A

B

C

D

PROPERTY OF:

SCALE

SIZE DWG. NO.

A

REV.

MATERIAL



12345678

CHAIN,COUP,DISA

B

C

D

12345678

SIOUX AUTOMATION CENTER INCSIOUX AUTOMATION CENTER INCSIOUX AUTOMATION CENTER INCSIOUX AUTOMATION CENTER INC877 FIRST AVE NW SIOUX CENTER, IA 51250877 FIRST AVE NW SIOUX CENTER, IA 51250877 FIRST AVE NW SIOUX CENTER, IA 51250877 FIRST AVE NW SIOUX CENTER, IA 51250

MON700143 B

DRAWN BY

BMCHECKED DATE

DATE

4-94

BREAK ALL EDGES .03 X 45

AS NOTED


DWG. NO.

MON700143

1:1.5

REVISIONS

ECN REV DESCRIPTION DATE BY CHK

REV B

SHEET OF1 1

VM10-98MON800158 WAS MON800112AECN

1964 B ADD: SPASNC14X12 QTY2 12-02 CV

2

5

1

3

4

4ITEM NO. QTY. PART NO. DESCRIPTION

1 1 MON100846 RC402,18P,9IN

2 1 MON800158 SPK,40,B,18,1

3 1 RC402CON LINK,CONN,40-2

4 2 SPASNC14X12 SCREW,ALLEN,1/4,1/2,NC

5 1 SPK40B18X114 SPK,40,B,18,1.25

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVISIONS


REVBDWG NO.

MON700230


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

JLDATE

12-00

1:3

AS SHOWN MON700230 B

CHUTE,FLIP,CYL,ASSY

SHEET OF 11

744

A

B JL

VM

12-00

2-95MON700253 WAS MON700189

MON100955 WAS MON100251HYD6801-6-6 WAS HYD6400-6-8

9

97

21111

31 8

7

10

4

5

6


1 1 MON100393 BRKT,RAM,CLY,CHUTE

2 1 MON100955 CYL,HYD,2,8,W/CNTRBAL,PAINTED

3 1 NUT34JAMNF NUT,HEX,JAM,3/4,NF,G8

4 2 BLT38X1CNC BLT,CARR,3/8,1,NC,G2


6 2 NUT38NC NUT,HEX,3/8,NC,G5

7 2 SPCP316X112 PIN,COTTER,3/16,1-1/2

8 1 SPBUS58NR14G BUSHING,MACH,.625,NR,14GA

9 2 MON700253 HOSE,HYD,3/8,62

10 1 MON700171 BRKT,CHUTE,FLIP

11 2 HYD6801-6-6 ADPT,ELBOW,06,MJIC,06,MORG,90D

REVISIONS


ITEM # QTY PART # DESCRIPTION

17 1 STIWIRE14PR39 WIRE,PRIMARY,14GA,GREEN

16 1 STIWIRE14PR38 WIRE,PRIMARY,14GA,WHITE

15 1 STIWIRE14PR06 WIRE,PRIMARY,14GA,BROWN

14 1 STIWIRE14PR05 WIRE,PRIMARY,14GA,YELLOW

13 1 STIWIRE14PR02 WIRE,PRIMARY,14GA,RED

12 1 STIWIRE14PR01 WIRE,PRIMARY,14GA,BLACK

11 2 STI700921 LIGHT,CLRNC,2-1/2",SEALED,AMBR

10 1 STI700200 CLAMP,LOOM,.5

9 7 STI700193 GROMMET,MOUNT,FLUSH,2.5

8 5 STI700148 LIGHT,CLRNC,2-1/2",SEALED,RED

7 1 STI14SHRINK TUBING,SHRINK,HEAT,.25,1

6 1 SPZBJ64931 LIGHT,BUNK,TRK,MOUNT

5 7 SPB14249 CONN,PLUG,STD,LIGHT

4 2 KN174794 LIGHT,OVAL,BACKUP,2.25,6.5

3 4 KN174725 GROMMET,LIGHT,OVAL

2 4 KN174724 CONNECTOR,LIGHT,ANGLE,RT

1 2 KN174674 LIGHT,OVAL,RED,STOP

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1REVZZDWG NO.

MON900467


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

CMDATE

05-04

1:24


LIGHT,TRK,2070,ASSY

SHEET OF 11


RAW MAT.

AREA

CUT LENGTH

PERIMETER

5 9 8

59

8

2

2

3

4

1

119

5

NOTE: 1) RUN WIRE WITHIN CONDUIT TUBES2) SECURE WIRE WITH LOOM CLAMPS AT EXPOSED CATCH POINTS3) REFER TO MON900467-1 FOR ELECTICAL SCHEMATIC

5 9 8

59

8

2

2

3

4

1

119

5

NOTE: 1) RUN WIRE WITHIN CONDUIT TUBES2) SECURE WIRE WITH LOOM CLAMPS AT EXPOSED CATCH POINTS3) REFER TO MON900467-1 FOR ELECTICAL SCHEMATIC

D

C

B

A

B

C

D

12345678

8 7 6 5 4 3 2 1

REVISIONS


REV DWG NO.

MON900402


DRAWN

DATECHECKED




MATERIAL

PROPERTY OF


REVDWG NO.SIZE

B

APDATE

8-02

1:36

AS NOTED MON900402

LIGHT,ASSY,2090

SHEET OF 11

4 5

65

7

1

2 3 9


1 2 KN174794 LIGHT,OVAL,CLEAR,BACKUP

2 2 KN174674 LIGHT,OVAL,RED,STOP

3 2 KN174725 GROMMET,LIGHT,OVAL

4 5 STI700148 LIGHT,CLRNC,2-1/2",SEALED,RED

5 5 STI700193 GROMMET,MOUNT,FLUSH,2.5

6 2 STI700921 LIGHT,CLRNC,2-1/2",SEALED,AMBR

7 1 SPZBJ64931 LIGHT,BUNK,TRK,MOUNT

8 2 SPB14418 GROMMET,MOUNT,FLUSH,2.5,CLOSED

9 2 KN174724 CONNECTOR,LIGHT,ANGLE,RT

10 2 SPB14249 CONN,PLUG,STD,LIGHT

11 16 JES422005 CONN,BUTT,BLUE,16-14

12 1000 STIWIRE14PR WIRE,PRIMARY,14GA,COLOR

6 8 10

1

2 3 9

4 8 10

45

GENERAL SPECIFICATIONS 2070 TRUCK MOUNT WIDTH: MIXING CHAMBER...........................95” (241 cm) OVERALL..................................96” (244 cm) LENGTH: MIXING CHAMBER.........................192” (488 cm) OVERALL (BOX ONLY)................................217” (551 cm)

HEIGHT: (DETERMINED BY TIRE SIZE)...............134” (356 cm) CAPACITY: .................................710 CU/FT (20.10 m3) (STRUCK LEVEL)……………….665 BUSHELS UNIT WEIGHT: (BOX ONLY)…….......................16000 LBS (7257.48Kg) BOTTOM SECTION: ............. 5/16 STEEL PLATE WITH STAINLESS LINER AND WEAR BARS UPPER SIDES: ...................... 1/4 STEEL PLATE FRONT/REAR: .......................5/16 STEEL PLATE DISCHARGE: .........................40" DISCHARGE WITH BOTH STANDARD AND EXTENDED LENGTHS HYDRAULICALLY DRIVEN; ON LEFT SIDE OF MIXER DRIVE: ............................HYDROSTATIC and CHAIN MINIMUM HORSEPOWER REQUIREMENT: ...............300 HP (224 Kw) MIN.

WARRANTY

MAXIMIXER warrants to the initial purchaser of a new MAXIMIXER product from an authorized MAXIMIXER dealer that the product and the components thereof manufactured by MAXIMIXER are free from defects in material and workmanship at the time of shipment. MAXIMIXER further warrants to such purchaser that each new MAXIMIXER product will perform without structural or operational failure if the product is assembled and mounted in accordance with MAXIMIXER 's instruction and drawing and is then operated and maintained as described in the Owner's Manual.

WARRANTY PERIOD The above warranty shall be effective for a period of two years on workmanship and materials from the date of delivery by the MAXIMIXER dealer to the initial purchaser. PURCHASER'S REMEDIES If a warranted MAXIMIXER product or component fails to conform to the above warranty during the two year warranty period, MAXIMIXER will furnish the parts, and labor at the factory necessary to correct such failure, provided MAXIMIXER is notified through the selling representative within 30 days of the discovery of the failure. All warranty submissions must include the original part in question, along with a properly filled out warranty claim sheet, before a warranty award will be made. Labor at the factory is specified as labor done at the MAXIMIXER factory ONLY! MAXIMIXER will pay the common carrier freight expense of parts to and from the owner. Faster freight service is available, with the owner paying the difference in cost between common carrier and preferred method by owner. Freight of whole goods to or from the factory is the owner’s expense, regardless if they fall under warranty or not. All warranty decisions will be final! EXCLUSIONS This warranty shall not apply to component parts or accessories of products not manufactured by MAXIMIXER and which carry the warranty of the manufacturer thereof. Items of high wear and regular maintenance shall not be covered under this warranty. This warranty shall be void if any part or parts not manufactured by MAXIMIXER are used either in maintaining or servicing of the products covered by this warranty. No warranty whatsoever is made on used, secondhand, altered, or rebuilt machinery. THIS WARRANTY IS EXTENDED TO THE INITIAL PURCHASER FROM AN AUTHORIZED MAXIMIXER DEALER AND MAY NOT BE ASSIGNED. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FOR A PARTICULAR PURPOSE AND MAXIMIXER NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE THEREOF. We reserve the right to make improvements to any of our products without notice of obligation regarding models previously sold.

Documents

MODEL 2070 › wp-content › uploads › ...MODEL 2070 OPERATION AND MAINTENANCE MANUAL 877 1st. AVE. NW Sioux Center, IA. 51250 Iowa 1-712-722-1488 . TAKE NOTE! THIS SAFETY ALERT