MiniDisc Recorder · consult your nearest Sony dealer. Welcome! Thank you for purchasing the Sony MiniDisc Recorder. Before operating the recorder, please read this manual thoroughly

2-346-664-12(1)

MiniDisc Recorder

Operating Instructions

1998 by Sony Sound Tec Corporation

MDS-E11

2

On operationIf the recorder is brought directly from acold to a warm location, or is placed in avery damp room, moisture maycondense on the lenses inside therecorder. Should this occur, therecorder may not operate properly. Inthis case, remove the MD and leave therecorder turned on for about an houruntil the moisture evaporates.

On the MiniDisc cartridge• Do not open the shutter to expose the

MD.• Do not place the cartridge where it

will be subject to extremes ofsunlight, temperature, moisture ordust.

On cleaningClean the cabinet, panel and controlswith a soft cloth slightly moistened witha mild detergent solution. Do not useany type of abrasive pad, scouringpowder or solvent such as alcohol orbenzine.

If you have any questions or problemsconcerning your recorder, pleaseconsult your nearest Sony dealer.

Welcome!Thank you for purchasing the SonyMiniDisc Recorder. Before operatingthe recorder, please read this manualthoroughly and retain it for futurereference.

About This ManualConventions• Controls in the instructions are those

on the recorder; these may, however,be substituted by controls on theremote that are similarly named or,when different, appear in theinstructions within brackets.

• The following icons are used in thismanual:

Indicates a procedure thatrequires use of the remote.

Indicates tips for making thetask easier and hints.

INFORMATIONThis equipment has been tested andfound to comply with the limits for aClass A digital device, pursuant to Part15 of the FCC Rules. These limits aredesigned to provide reasonableprotection against harmful interferencein a residential installation. Thisequipment generates, uses, and canradiate radio frequency energy and, ifnot installed and used in accordancewith the instructions, may causeharmful interference to radiocommunications.However, there is no guarantee thatinterference will not occur in aparticular installation. If this equipmentdoes cause harmful interference to radioor television reception, which can bedetermined by turning the equipmentoff and on, the user is encauraged to tryto correct the interference by one ormore of the following measures:

– Reorient or relocate the receivingantenna.

– Increase the separation between theequipment and receiver.

– Connect the equipment into an outleton a circuit different from that towhich the receiver is connected.

– Consult the dealer or an experiencedradio / TV technician for help.

Precautions

On safety (Rifer to the supplied“WARNING”.)Should any solid object or liquid fallinto the cabinet, unplug the recorderand have it checked by qualifiedpersonnel before operating it anyfurther.

On power sources• Before operating the recorder, check

that the operating voltage of therecorder is identical with your localpower supply. The operating voltageis indicated on the nameplate at therear of the recorder.

• If you are not going to use therecorder for a long time, be sure todisconnect the recorder from the walloutlet. To disconnect the AC powercord, grasp the plug itself; never pullthe cord.

• AC power cord must be changed onlyat the qualified service shop.

WARNING

Notice for the Customers in theUnited Kingdom

IMPORTANTThe wires in this mains lead arecoloured in accordance with thefollowing code:

Blue : NeutralBrown : Live

As the colours of the wires in the mainslead of this apparatus may notcorrespond with the coloured markingsidentifying the terminals in your plug,proceed as follows:The wire which is coloured blue mustbe connected to the terminal which ismarked with the letter N or colouredblack.The wire which is coloured brown mustbe connected to the terminal which ismarked with the letter L or colouredred. Do not connect either wire to theearth terminal in the plug which ismarked by the letter E or by the safetyearth symbol Y or coloured green orgreen-and-yellow.

To prevent fire or shockhazard, do not expose the unitto rain or moisture.

To avoid electrical shock, donot open the cabinet. Referservicing to qualifiedpersonnel only.

This symbol is intended to alert theuser to the presence of uninsulated“dangerous voltage” within theproduct’s enclosure that may be ofsufficient magnitude to constitute arisk of electric shock to persons.

This symbol is intended to alert theuser to the presence of importantoperating and maintenance(servicing) instructions in theliterature accompanying theappliance.

* The location of the marking is at the rear ofthe enclosure.

z

Z

3

TABLE OF CONTENTS

Getting StartedUnpacking ........................................................................................................................... 4Connection .......................................................................................................................... 4

Basic OperationsRecording on an MD ......................................................................................................... 6Playing an MD .................................................................................................................... 8

Recording on MDsNotes on Recording ........................................................................................................... 9Useful Tips for Recording ................................................................................................ 9Recording Over Existing Tracks ..................................................................................... 11Adjusting the Recording Level ....................................................................................... 11Marking Track Numbers While Recording (Track Marking) ................................... 12Starting Recording With 6 Seconds of Prestored Audio Data(Time Machine Recording) .............................................................................................. 12Synchro-Recording With Audio Equipment of Your Choice .................................... 13Synchro-Recording With a Sony CD Playe .................................................................. 14Recording Using a Timer ................................................................................................. 15

Playing MDsUsing the Display ............................................................................................................. 16Locating a Specific Track ................................................................................................. 17Locating a Particular Point in a Track ........................................................................... 18Playing Tracks Repeatedly .............................................................................................. 18Playing Tracks in Random Order (Shuffle Play) ......................................................... 19Creating Your Own Program (Program Play) ............................................................. 20Useful Tips When Recording From MDS to Tape....................................................... 21Playing Using a Timer...................................................................................................... 22

Editing Recorded MDsNotes on Editing ............................................................................................................... 22Erasing Recordings (Erase Function) ........................................................................... 22Dividing Recorded Tracks (Divide Function) .............................................................. 24Combining Recorded Tracks (Combine Function) ..................................................... 25Moving Recorded Tracks (Move Function) .................................................................. 26Labeling Recordings (Title Function) ............................................................................ 26Undoing the Last Edit (Undo Function) ...................................................................... 29

Additional InformationFunction of Control Terminal ......................................................................................... 29Dimensions ........................................................................................................................ 30Functions of REMOTE Terminals .................................................................................. 31Display Messages .............................................................................................................. 34System Limitations ........................................................................................................... 34Troubleshooting ................................................................................................................ 35Specifications ..................................................................................................................... 36Index of Parts and Controls ............................................................................................ 37Guide to the Serial Copy Management System ........................................................... 38

Getting Started

4

Connection

Overview

This section describes how to hook up the MD recorderto other components such as a mixer, CD player orDAT recorder. Be sure to turn off the power of eachcomponent before connection.

Getting Started

UnpackingCheck that you received the following items:• Remote commander (remote) RM-D7M (1)• R6 (size AA) batteries (2)

Inserting batteries into the remote

You can control the recorder using the suppliedremote.Insert two R6 (size AA) batteries by matching the +and – on the batteries. When using the remote, point itat the remote sensor g on the recorder.

z When to replace batteriesWith normal use, the batteries should last for about sixmonths. When the remote no longer operates therecorder, replace all the batteries with new ones.

Notes• Do not leave the remote near an extremely hot or humid

place.• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage frombattery leakage and corrosion.

CD player, DATrecorder, or MDrecorder, etc.

to a walloutlet

Mixer

MDS-E11

External controller

: Signal flow

OUT IN

DIGITALCOAXIAL OUT

DIGITALCOAXIAL IN

Mixer

OUT IN

PC or similarequipment

Remote controller,or other controller

Getting Started

5

What cords will I need?

• Audio connecting cords (pin type)

• Audio connecting cords (XLR type)

• Coaxial digital connecting cable

• Control-S cord (mini-jack type)

• Relay recording/playback cord (such as RK-G136)

Connection

• Connecting the recorder to an analog deviceUse the terminals and switches shown below.

Switch the rear-panel ANALOG INPUT according to thetype of the input terminal used.

z Regardless of the setting of the ANALOG INPUTswitch, signals are transferred to both the UNBALand BAL output terminals.

z If you use the BALANCE output terminal (XLR type),you can use the OUTPUT LEVEL switch to switch theoutput level.

Red (R)

White(L)

White(L)

Red(R)

The BALANCE I/O connector specifications are as follows:

• Connecting the recorder to a digital component suchas a CD player, DAT recorder, another MD recorder, ormixerConnect the component through the DIGITAL IN/OUTconnectors with two coaxial digital connecting cables.

z Automatic conversion of digital sampling ratesduring recordingA built-in sampling rate converter automaticallyconverts the sampling frequency of various digitalsources to the 44.1 kHz sampling rate of your MDrecorder.This allows you to record sources such as 32 and48 kHz DAT or satellite broadcasts, as well as compactdiscs and other MDs.

Connecting the AC power cordConnect the AC power cord to a wall outlet.

ççççç: Signal flow

MD recorder Digital component

OUTPUT LEVEL switch

To record through Set INPUT to

UNBAL IN (pin type) UNBAL

BAL IN (XLR type) BAL

Switch setting

+4dBu

–10dBu

Output level

Signals having a metered level of –20 dBare generated at a +4 dBu level.

Signals having a metered level of –20 dBare generated at a –10 dBu level.

Output terminal XLR-3-32equivalent

(stereo mini-jack type) (stereo mini-jack type)

Analog I/O terminalUNBAL (pin type)

Analog I/O terminalBAL (XLR type)

ANALOG INPUT switch

Input terminal XLR-3-31equivalent

1 : GND2 : HOT3 : COLD

1 : GND2 : HOT3 : COLD

Basic Operations

6

Recording on an MDBasic Operations

1 Turn on the mixer and program source.

2 Press U.

3 Insert a recordable MD.

With the arrowpointing this way

With the label side up

If the MD has a recorded material on it, the recorder willautomatically start recording from the end of the last recordedtrack.

4 Set INPUT to the corresponding input connector.

5 Select a recording mode from the Set up Menu.

2 3

768

5 4

To record through Set INPUT to

ANALOG IN

DIGITAL

ANALOG

DIGITAL IN COAXIAL

BAL or UNBAL

1 Press EDIT/NO twice to display “Setup Menu.”2 Wait until “Rec Mode” appears in the display, when press AMS.3 Turn AMS to the desired recording mode (STEREO or MONO) and press

AMS.4 Press EDIT/NO..

Monaural recording will last about two times longer than stereo recording.

Analog input

When using the analog input,switch the rear-panel ANALOGINPUT (BAL or UNBAL) acordingto the type of the input terminalused.

Monitor audio during recording

Even if you set REC MODE toMONO, the monitor signal doesnot become monaural.

Recording mode

The last recording mode in effectwill be restored even when youreplace the MD or turn therecorder off and on.

Basic O

pera

tion

s

Basic Operations

7

6 Press r.The recorder stands by for record.

7 When recording the analog input signal, adjust the recordinglevel with REC LEVEL.The fourth dot is satisfactory for most purposes. For details,refer to “Adjusting the Recording Level” on page 11.

8 Press · or P.Recording starts.

9 Start playing the program source.

Do not turn off the power or disconnect the recorder from the power sourceimmediately after recording.

If you do, recorded material may not be saved to the MD. To save thematerial, after recording, press § EJECT to take out the MD. “TOC” indicatorwill flash in the display at this time.After “TOC” indicator stops flashing and is unlit, you can turn off the poweror pull out the AC power cord.

To Press

Stop recording

Pause recording* P. Press the button again or press · toresume recording.

p

Take out the MD § EJECT after stopping recording

* Whenever you pause recording, the track number increases by one. For example, ifyou paused recording while recording on track 4, the track number increases byone and recording continues on the new track when restarted.

To protect an MD against accidental erasure

To make it impossible to record on an MD, slide the tab in the direction ofarrow, opening the slot. To allow recording, close the slot.

Rear of the disc

Slide the tab inthe direction of arrow

Record-protect tab

When ”TOC“ indicator flashes inthe display

The recorder is currently updatingthe Table Of Contents (TOC).Do not turn off the power, movethe recorder, or pull out the ACpower cord, while “TOC”indicator is flashing. Changes to anMD made through recording aresaved only when you update theTOC by ejecting the MD.

Basic Operations

8

Playing an MD

1 Turn on the mixer and adjust the fader or level control of thecorresponding channel.

2 Press U.

3 Insert an MD.

z You can locate and play backa track while the recorder isstopped1 Turn AMS (or press =

or + on the remote)until the number of thedesired track appears.

2 Press AMS or ·.

z To use headphonesConnect them to PHONESjack. Use PHONE LEVEL toadjust the volume.

4 Press ·.The recorder starts playing.

Pause playing

Stop playing

Do the following:

Press p.

Press P. Press the button again or press· to resume playing.

To

Turn AMS counterclockwise (or press= on the remote).

Go to the preceding track

Go to the next track Turn AMS clockwise (or press + onthe remote).

Press § EJECT.Take out the MD

With the label side upWith the arrowpointing this way

2 3 4

9

Recording on MDsRecording on MDs

Notes on Recording

If “Protected” appears in the displayThe MD is record-protected. Close the slot to record on thedisc (see “To protect an MD against accidental erasure” onpage 7).

If “Din Unlock” flashes in the display• The digital program source which you set with INPUT in

Step 4 on page 6, is not connected.To continue, connect the program source properly.

• The program source is not on.Turn on the program source.

Depending on the source being recorded, track numbersare marked in the following ways:• When recording from a CD or MD with INPUT set to

DIGITAL and the source connected through DIGITAL IN:The recorder automatically marks track numbers in thesame sequence as the original. If, however, a track isrepeated two or more times (e.g. by single-track repeatplay) or two or more tracks with the same track number(e.g. from different MDs or CDs) are played, the track ortracks are recorded as a single, continuous track with asingle track number.If the source is an MD, track numbers may not be markedfor tracks of less than 4 seconds.

• When recording from DAT or satellite broadcasts withINPUT set to DIGITAL, the recorder automatically marksa track number whenever the sampling frequency of theinput signal changes.

When “TOC” indicator flashes in the displayThe recorder is currently updating the Table Of Contents(TOC). Do not turn off the power, move the recorder, or pullout the AC power cord. Changes to an MD made throughrecording are saved when you update the TOC by ejectingthe MD.

When the program mode is set to PROGRAM or SHUFFLE(see pages 19 and 20) It is automatically switched to CONTINUE and theequipment enters the recording standby state.

If “Cannot Copy” appears in the displayThe recorder uses the SCMS (Serial Copy ManagementSystem).MDs recorded through digital input connector cannot becopied onto other MDs or DAT tapes through the digitaloutput connector (see page 38).

When recording digital signals that have been emphasized(in the higher frequencies)The signal is automatically de-emphasized (with attenuationproportional to the degree of emphasis) and the level of thede-emphasized signal is indicated on the peak level meters.

When the recorder is recording or in recording pause,digital signals input through DIGITAL IN are output toDIGITAL OUT with the same sampling rate.To change the digital input signal to another sampling ratefor output (without recording it to an MD), use InputMonitor Function (see page 10).

Useful Tips for Recording Z

Checking the remaining recordable time onthe MD• When you press DISPLAY repeatedly while

recording, the display changes as follows: elapsedrecording time, remaining recordable time on theMD, track name.

• When you press DISPLAY repeatedly while therecorder is stopped, the display changes as follows:total recorded time, remaining recordable time onthe MD, disc name (see page 16).

Basic O

pera

tion

s

(Continued)

Recording on MDs

10

Monitoring the input signal (Input Monitor)Before starting recording, you can monitor the selectedinput signal through the recorder’s output connectors.

1 Press §EJECT to remove the MD.

2 Set INPUT according to the input signal you wantto monitor.

When INPUT is set to ANALOGThe analog signal input through LINE (ANALOG) IN isoutput to DIGITAL OUT after A/D conversion, andthen to the LINE (ANALOG) OUT connectors andPHONES jack after D/A conversion.

When INPUT is set to DIGITALThe digital signal input through DIGITAL IN is outputto DIGITAL OUT, and then to the LINE (ANALOG)OUT connectors and PHONES jack after D/Aconversion.

NoteEven if you set REC MODE to MONO, the monitorsignal does not become monaural.

3 Press r.If INPUT is set to ANALOG, “AD-DA” appears inthe display.If INPUT is set to DIGITAL, “-DA”appears in thedisplay.

If “Auto Cut” appears in the display(Auto Cut)There has been no sound input for 30 seconds whileINPUT is set to DIGITAL and the source is connectedthrough DIGITAL IN. The 30 seconds of silence arereplaced by a blank of about 3 seconds and therecorder changes to recording pause.

z You can turn off the Auto Cut FunctionFor details, see “If “Smart Space” appears in thedisplay” below.

If “Smart Space” appears in the display(Smart Space)When there has been an extended silence of up to 30seconds in length, and the signal is input again, thesilence is replaced by a blank of about 3 seconds andthe recorder continues recording.

NoteHowever, if you begin recording during such an extendedsilent portion, the smart space function will not be activated.

To turn off the Smart Space Function and Auto CutFunction1 While the recorder is stopped, press EDIT/NO twice to

display “Setup Menu”.2 Turn AMS until “Smart Space” menu appears in the

display, then press AMS.3 Turn AMS until “S.Space OFF” appears in the display,

then press AMS.4 Press EDIT/NO.

To turn on the Smart Space Function and Auto CutFunction again1 Carry out Steps 1 and 2 in “To turn off the Smart Space

Function and Auto Cut Function” above.2 Turn AMS until “S.Space ON” appears in the display, then

press AMS.3 Press EDIT/NO.

Notes• When you turn off the Smart Space Function, the Auto Cut

Function is also turned off automatically.• The Smart Space Function and Auto Cut Function are

factory set to on.• If you turn off the recorder or disconnect the AC power

cord, the recorder will recall the last setting (on or off) ofthe Smart Space and Auto Cut Functions the next time youturn on the recorder.

11

Recording on MDs

Recording Over Existing TracksFollow the procedure below to record over existingmaterial just as you would on an analog cassette tape.

1 Carry out Steps 1 to 5 in “Recording on an MD”on page 6.

2 Turn AMS (or press = or +) until thenumber of the track to be recorded over appears.

3 To record from the start of the track, continuefrom Step 6 in “Recording on an MD” on page 7.

z To record from the middle of the track1 After Step 2 above, press · to start playback.2 Press P where you want to start recording.3 Continue from Step 6 in “Recording on an MD” on

page 7.

NoteYou cannot record from the middle of the track during“PROGRAM”or “SHUFFLE”play.

Adjusting the Recording LevelWhen recording with INPUT set to ANALOG and thesignal input through LINE (ANALOG) IN jacks, useREC LEVEL to adjust the recording level beforestarting recording.You cannot adjust the recording level during digitalrecording.

1 Carry out Steps 1 to 6 in “Recording on an MD”on pages 6 and 7.

2 Play the portion of the program source with thestrongest signal level.

3 While monitoring the sound, turn REC LEVEL toadjust the recording level so that the peak levelmeters reach their highest point without turningon the OVER indication. Occasional lighting of“OVER” is acceptable.

4 Stop playing the program source.

5 To start recording, follow the procedure startingfrom Step 8 in “Recording on an MD” on page 7.

r

6

)0

+=

pP·

≠ AMS ±

=/+

REC LEVEL

Recording on MDs

12

Marking Track Numbers WhileRecording (Track Marking)You can mark track numbers either manually orautomatically. By marking track numbers at specificpoints, you can quickly locate the points later using theAMS Function or Editing Functions.

To Cancel Auto Track Marking1 While the recorder is stopped, press EDIT/NO twice to

display “Set up Menu”.2 Turn AMS until “Level Sync” appears in the display, then

press AMS.3 Turn AMS until “Level Sync OFF” appears in the display,


To Turn on Auto Track Marking1 Carry out Steps 1 and 2 in “To Cancel Auto Track

Marking” above.2 Turn AMS until “Level Sync ON” appears in the display,


z When you want to mark track numbers after you‘vefinished recordingUse the Divide Function (see “Dividing RecordedTracks” on page 24.)

NoteIf you turn off the recorder or disconnect the AC power cord,the recorder will recall the last setting (Level Sync ON orOFF) of the Automatic Track Marking Function the next timeyou turn on the recorder.

Starting Recording With6 Seconds of Prestored AudioData (Time Machine Recording)When recording from an FM or satellite broadcast, thefirst few seconds of material are often lost due to thetime it takes you to ascertain the contents and press therecord button. To prevent the loss of this material, theTime Machine Recording Function constantly stores 6seconds of the most recent audio data in the buffermemory so that when you begin recording theprogram source, the recording actually begins with the6 seconds of audio data stored in the buffer memory inadvance, as shown in the illustration below:

End of the programsource to be recorded

Time

Recordedportion

When you pressAMS in Step 3

Audio data in 6-second buffer memory

Beginning of the programsource to be recorded

Marking track numbers manually(Manual Track Marking)You can mark track numbers at any time whilerecording on an MD.

Press r at the place you want to add a track markwhile recording.

Marking track numbers automatically(Automatic Track Marking)The recorder adds track marks differently in thefollowing cases:• When recording from CDs or MDs with INPUT set

to DIGITAL and the source connected throughDIGITAL IN:The recorder marks track numbers automatically.When you record from a CD or MD, the tracknumbers are marked as they are found on theoriginal.

• In the case other than the aboveThe LEVEL-SYNC function assigns a track numberautomatically each time the input signal of thesource falls to a given level or below and a new inputsignal exceeding that level is received.

EDIT/NO YES

r

13

Recording on MDs

Synchro-Recording With AudioEquipment of Your Choice ZBy using the MUSIC SYNC button on the remote, youcan automatically start a Synchronized recording withthe signal input from the program source through theinput jacks.The method of marking track numbers differs,depending on the program source being recorded andhow the recorder is connected to the program source.(See “Notes on Recording” on page 9.)

1 Carry out Steps 1 to 5 in “Recording on an MD”on page 6.

2 Press MUSIC SYNC.The recorder changes to recording pause.

3 Start playing the program source you want torecord.The recorder starts recording automatically.

z To stop Music Synchro-RecordingPress p.

NoteDuring Music Synchro-Recording, the Smart Space Functionand the Auto Cut Function turn on automatically regardlessof their settings (ON or OFF) and type of input (digital oranalog).

1 Carry out Steps 1 to 6 in “Recording on an MD”on pages 6 and 7.The recorder changes to recording pause.

2 Start playing the program source you want torecord.The most recent 6 seconds of audio data is storedin the buffer memory.

3 Press AMS (or T.REC) to start Time MachineRecording.Recording of the program source starts with the6 seconds of audio data stored in the buffermemory.

z To stop Time Machine RecordingPress p.

NoteThe recorder starts storing audio data when the recorder isin recording pause and you start playing the programsource. With less than 6 seconds of playing of the programsource and audio data stored in the buffer memory, TimeMachine Recording starts with less than 6 seconds of audiodata.

r

6

)0

+=

pP·

r

6

)0

+=

pP·

≠ AMS ±

T.REC

MUSIC SYNC

Recording on MDs

14

Synchro-Recording With a SonyCD Player ZBy connecting your recorder to a Sony CD player, youcan easily dub CDs onto MDs using the CD synchrobuttons on the remote. If your recorder is connected toa Sony CD player by a digital input cable, tracknumbers are automatically marked as on the original,regardless of whether “LevelSync ON” or“LevelSyncOFF” is selected. If your recorder isconnected to a Sony CD player by audio connectingcords through LINE (ANALOG) IN, track numbers areautomatically marked when you select “LevelSyncON” (see “Marking Track Numbers While Recording”on page 12).As the same remote controls both the CD player andthe recorder, you may have trouble operating bothunits if they are far from each other. If you do, placethe CD player close to this recorder.

1 Turn on the CD player and the mixer.

2 Carry out Steps 2 to 5 in “Recording on an MD”on page 6 to prepare the recorder for recording.

3 Insert a CD into the CD player.

4 Select the playback mode (Shuffle Play, ProgramPlay, etc.) on the CD player.

5 Press STANDBY.The CD player pauses for playing and therecorder pauses for recording.

6 Press START.The recorder starts recording and the CD playerstarts playback.The track number and elapsed recording time ofthe track appear in the display.

If the CD player does not start playingSome CD player models may not respond when youpress START on the remote of the recorder. Press P onthe remote of the CD player instead.

7 Press STOP to stop synchro-recording.

To pause recordingPress STANDBY or CD PLAYER P.To restart recording, press START or CD PLAYER P.A new track number is marked each time you pauserecording.

z You can use the remote of the CD player duringsynchro-recordingWhen you press p, the CD player stops and therecorder pauses for recording.When you press P, the CD player pauses and therecorder pauses for recording.To restart synchro-recording, press ·.

z You can change CDs during synchro-recordingCarry out the following steps instead of Step 7 above.1 Press p on the remote of the CD player.

The recorder pauses for recording.2 Change the CD.3 Press · on the remote of the CD player.

Synchro-recording restarts.

z You can also do synchro-recording with a Sony videoCD playerUsing the procedure for synchro-recording with a SonyCD player, you can do synchro-recording with a Sonyvideo CD player also.To select the video CD player, press button number 2while pressing down the POWER button before startingthe procedure.To select the CD player again, press button number 1while pressing down the POWER button.The recorder is factory set to CD player for synchro-recording.

z You can check the remaining recordable time on theMDPress DISPLAY on the remote controller.

r

6

)0

+=

+=P

pP·STANDBY

START

STOP

CD PLAYER P

15

Recording on MDs

Recording Using a TimerA commercially available timer connected to therecorder allows it to start or stop recording at apreappointed time. For additional information, refer tothe information manual for the timer.

1 Turn on the timer.

2 Perform steps 1 to 5 in “Recording on an MD”(see page 6).

3 Choose “Timer REC” from the Setup Menu.1. While the recorder is stopped, press EDIT/NO

twice to display “Setup Menu.”2. Turn AMS until “Timer” appears in the display,

then press AMS.3. Turn AMS until “Timer REC” appears in the

display, then press AMS.4. Press EDIT/NO.

4 Set the timer to the desired operation.

5 Having finished recording with a timer, choose“Timer OFF” from the Setup Menu.1. Perform steps 1 and 2 in step 3 above.2. Turn AMS until “Timer OFF” appears in the

display, then press AMS.3. Press EDIT/NO.If you leave the setup Menu “Timer REC” setting,the recorder will begin recording automaticallynext time it is powered on.

After timer recording, be sure to turn on the recorder within onemonthWhen you turn on the recoder next time, the recording willbe transfferd to the MD. If you leave the recorderunpowered, the recording will not be transferred to the MDwhen you turn on the recorder.

16

Playing MDs

Using the Display ZYou can use the display to check disc and trackinformation such as the total track number, totalplaying time of the tracks, remaining recordable timeof the disc and disc name.

When you insert an MD, the disc name, total numberof tracks, and total disc playing time appear in thedisplay as follows:

Total number of tracks Total disc playing time

To label a recordable disc and its tracks, see “LabelingRecordings” on page 26.

NoteWhen you insert a new MD or turn off the recorder and turnit on again, the last item displayed will reappear.However, if you disconnect the AC power cord, the displaywill show the total number of tracks and total disc playingtime of all recorded tracks the next time you turn on therecorder, no matter what the last display was.

Disc name

Checking the total track number, total discplaying time, remaining recordable time ofthe disc and the title of the discEach time you press DISPLAY/CHAR (or DISPLAY)while the recorder is stopped, you can change thedisplay as follows:

Remaining recordable time of the disc(Recorded MDs only)

Disc name

Press

Press

The remaining recordable time of the discis not shown for premastered MDs.

Press

Total number of tracks and total disc playingtime of all recorded tracks

6

pP·

DISPLAY SCROLL

Playing MDs

Checking remaining time and the title of a trackPress DISPLAY on the remote controller while playinga track.Each time you press DISPLAY, the track number andremaining time of the current track are displayed in thefollowing sequence:

(Continued)

Track number and playing time of thecurrent track

Track number and remaining time of thecurrent track

Press

Press

Track name

Press

If no title is recorded, “No Name” appears,followed by the elapsed playing time.

17

Playing MDs

z You can check the track name at any time whileplaying an MD ZPress SCROLL on the remote.Since the display shows up to 12 characters at a time,press SCROLL again to see the rest of the track title ifthe title has 13 characters or more.Press SCROLL again to pause scrolling, and again tocontinue scrolling.

Locating a Specific TrackYou can quickly locate any track while playing a discby using AMS (Automatic Music Sensor), = and+, number buttons or M.SCAN on the remote.

z When you directly locate a track with a number over25 ZYou must press >25 first, before entering thecorresponding digits.Press >25 once if it is a 2-digit track number, and twiceif it is a 3-digit track number.To enter “0,” press button 10.Examples: • To play track number 30

Press >25 once, then 3 and 10.• To play track number 100

Press >25 twice, then 1, 10 and 10.

z You can change the playing time during music scan1 While the recorder is stopped, press EDIT/NO to

display “Setup Menu.”2 Turn AMS until “Music Scan” menu appears in the

display, then press AMS.3 Turn AMS to select the length of the Music SCAN

play within the range of 6 to 20 seconds, using stepsof about one second, then press AMS.

4 Press EDIT/NO.

z To pause playing at the beginning of a trackTurn AMS (or press = or +) after pausingplayback.

z To go quickly to the beginning of the last trackTurn AMS counterclockwise (or press =) while thedisplay shows the total number of tracks and total discplaying time, remaining recordable time of the disc, ordisc name (see page 16).

Playing MDs

Numberbuttons

r

6

)0

+=

pP·

≠ AMS ±

>25

·=/+

M.SCAN

Do the following:

The next orsucceeding tracks

During playback, turn AMS clockwise(or press + repeatedly) until youfind the desired track.

The current orpreceding tracks

During playback, turn AMScounterclockwise (or press =repeatedly) until you find the desiredtrack.

A specific trackdirectly Z

Press number buttons to enter thetrack number.

A specific track byusing AMS

1 Turn AMS until the desired tracknumber appears while the recorderis stopped.

2 Press AMS or ·.

To locate

By scanning eachtrack (music scan) Z

1 Press M.SCAN before you startplaying.

2 When you find the desired track,press · to start playing.

18

Playing MDs

Locating a Particular Point in aTrackYou can also use 0 and ) to locate a particularpoint in a track during playback or playback pause.

Playing Tracks Repeatedly ZYou can play tracks repeatedly in any play mode.

Press REPEAT.“R” appears in the display, and the recorder will repeatthe tracks as follows:

When the MD isplayed in

To cancel repeat playPress REPEAT until “R” (REPEAT) disappears from thedisplay.

Repeating the current trackWhile the track you want to repeat is playing in normalplay, press REPEAT several times until “REPEAT 1”appears in the display.

(Continued)

z When “OVER” appears during high speed searchIf the disc reaches the end while you are pressing )during playback pause, “OVER” appears in the display.Press 0 (or press 0) or turn AMS (or press =)counterclockwise to go back.

Notes• If the disc reaches the end while you are pressing )

during sound monitoring, the recorder stops.• Tracks that are only a few seconds long may be too short

to scan using the search function. For such tracks, it isbetter to play the MD at normal speed.

r

6

)0

+=

pP·

0/)

REPEAT

)

A˜B

Normal play (page 8)

Shuffle Play (page 19)

Program Play (page 20)

The recorder repeats

All the tracks

All the tracks in random order

The same program

To locate a point Press

While monitoring thesound

) (forward) or 0 (backward)and keep pressing until you findthe desired point.

Quickly by observingthe display duringplayback pause(high speed search)

) or 0 and hold until youfind the desired point. There isno sound output during thisoperation.

19

Playing MDs

Repeating a specific portion (A-B Repeat)ZYou can play a specific portion of a track repeatedly.This might be useful when you want to memorizelyrics.Note that you can only repeat a portion within theboundaries of a single track.

1 While playing a disc, press A˜B at the startingpoint (point A) of the portion to be playedrepeatedly.“Repeat- A-” appears in the display, with “-”showing in REPEAT.

2 Continue playing the track or press ) until youreach the ending point (point B), then press A˜Bagain.The specified interval is played repeatedly. Therecorder starts to play the specified portionrepeatedly.

To cancel A-B RepeatPress REPEAT or p.

Setting new starting and ending pointsYou can repeat the portion immediately after the currentlyspecified portion by changing the starting and endingpoints.1 Press A˜B while “REPEAT A-B” appears.

The current ending point B becomes the new startingpoint A and “Repeat- A-” appears in the display.

2 Continue playing the track or press ) until you reachthe new ending point (point B), then press A˜B again.The newly specified interval is played repeatedly.

NoteIf you turn off the recorder or disconnect the AC power cord,the recorder will recall the last setting of the Repeat Functionthe next time you turn on the recorder.The A-B Repeat settings, however, are lost.

Playing Tracks in RandomOrder (Shuffle Play) ZYou can have the recorder “shuffle” tracks and playthem in random order.

1 Press SHUFFLE in the remote controller while therecoder is stopped.“S” is displayed in PLAY MODE in the display.

2 Press · to start Shuffle Play.

To cancel Shuffle PlayPress CONTINUE in the remote controller while therecorder is stopped.PLAY MODE in the display changes to “C”.

z You can specify tracks during Shuffle Play• To play the next track, turn AMS clockwise (or press+).

• To play from the beginning of the current track again,turn AMS counterclockwise (or press =). Youcannot use AMS (or =) to go to tracks that havealready been played.

r

6

)0

+=

pP·

CONTINUESHUFFLE

·

Playing MDs

20

Playing MDs

Creating Your Own Program(Program Play) ZYou can specify the playback order of the tracks on anMD and create your own programs containing up to 25tracks.

z You can program the same track repeatedlyPress the appropriate number button as many times asyou want to repeat.

z The program remains even after Program Play endsWhen you press ·, you can play the same programagain.

Notes• The program created by the Program Play Function is lost

when you press §EJECT to take out the MD.• The program created by the Program Play Function is lost

when you turn off the recorder or disconnect the ACpower cord.

• The display shows “- -m - -s” instead of the total playingtime when the total playing time of the program exceeds160 minutes.

Checking the track orderYou can check the order of tracks in your programduring playback or playback pause.

Turn AMS (or press = or +) during playback orplayback pause. The track numbers appear in theorder they were programmed.

Changing the track orderYou can change the order of the tracks in yourprogram before you start playing.

1 Press PROGRAM on the remote controller whilethe recorder is stopped.

2 Press the number buttons to enter the tracks youwant to program in the order you want.To program a track with a number over 25, usethe >25 button (see page 17).

If you’ve made a mistakePress CLEAR, then press the correct number button.

3 Repeat Step 2 to enter other tracks. Each time youenter a track, the total program time is calculatedand appears in the display.

4 Press · to start Program Play.

To cancel Program PlayPress CONTINUE in the remote controller while therecorder is stopped. “P” (PLAY MODE) disappears from thedisplay.

Numberbuttons

r

6

)0

+=

pP·· pCLEAR

PROGRAMCONTINUE

>25

=/+

Erase the last track in theprogram Z

Add tracks to the end of theprogram

Change the whole programcompletely

Do the following:

Press CLEAR. Each time youpress this button, the lasttrack will be cleared.

Carry out Steps 2 and 3 in“Creating Your OwnProgram.”

1 Press CONTINUE.2 Carry out Steps 1 to 3 in

“Creating Your OwnProgram.”

To

21

Playing MDs

Useful Tips When RecordingFrom MDs to Tape ZThe Auto Space and Auto Pause Functions described inthis section make recording from MDs to tape moreeasy.

Inserting blank spaces while recording totape (Auto Space)The Auto Space Function inserts a 3-second blankspace between each track while recording from MDs totapes, allowing you to use the AMS function duringplayback later.

Press A.SPACE on the remote controller until a markappears in A.SPACE in the display.

To cancel Auto SpacePress A.SPACE on the remote controller until a markdisappears in A.SPACE in the display.

NoteIf the Auto Space Function is on while recording a selectioncontaining multiple track numbers, (for example, a medleyor symphony), blank spaces will be inserted within theselection whenever the track number changes.

A.SPACE

Pausing after each track (Auto Pause)When the Auto Pause Function is on, the recorderpauses after playing each track. Auto Pause isconvenient when recording single tracks or multiple,non-consecutive tracks.

Press A.SPACE on the remote controller until a markappears in A.PAUSE in the display.

To restart playbackPress · or P.

To cancel Auto PausePress A.SPACE on the remote controller until a markdisappears in A.PAUSE in the display.

NoteIf you turn off the recorder or disconnect the AC power cord,the recorder will recall the last setting of the Auto Space andAuto Pause Functions the next time you turn on therecorder.

6

pP·

Playing MDs

22

Playing MDs

Notes on EditingYou can edit the recorded tracks after recording, usingthe following functions:• Erase Function allows you to erase recorded tracks

simply by specifying the corresponding tracknumber.

• Divide Function allows you to divide tracks atspecified points so that you can quickly locate thosepoints afterwards, using the AMS function.

• Combine Function allows you to combine twoconsecutive tracks into one.

• Move Function allows you to change the order oftracks by moving a specific track to a desired trackposition.

• Title Function allows you to create titles for yourrecorded MDs and tracks.

If “Protected” appears in the displayThe recorder could not edit because the record-protect sloton the MD is open. Edit after closing the slot (see page 7.)

When “TOC” indicator flashes in the displayDo not move the recorder or pull out the AC power cord.After editing, “TOC” indicator lights continuously until youeject the MD. “TOC” indicator flashes while the recorder isupdating the TOC. When the recorder finishes updating theTOC, “TOC” indicator goes off.

Erasing Recordings(Erase Function)Follow the procedures below to erase:• A single track• All tracks• Part of a trackNote, however, that once erased, MD data cannotbe recovered.

EDIT/NO YES

≠AMS±

Editing Recorded MDs

Playing Using a TimerA commercially available timer connected to therecorder allows it to start or stop playing at apreappointed time. For additional information, refer tothe information manual for the timer.

1 Turn on the timer.

2 Perform steps 1 to 3 in “Playing an MD” (see page8).

3 Choose “Timer PLAY” from the Setup Menu.1. While the recorder is stopped, press EDIT/NO

twice to display “Setup Menu.”2. Turn AMS until “Timer” appears in the display,

then press AMS.3. Turn AMS until “Timer PLAY” appears in the

display, then press AMS.4. Press EDIT/NO.

4 Set the timer to the desired operation.

After Finishing Playing with a TimerIf you leave the setup Menu “Timer PLAY” setting, therecorder will begin playing automatically next time it ispowered on. If you are not playing with a timer, choose“Timer OFF” from the Setup Menu.

23

Playing MDs

Erasing a single trackYou can erase a track simply by specifying therespective track number. When you erase a track, thetotal number of tracks on the MD decreases by one andall tracks following the erased one are renumbered.Since erasing merely updates the TOC, there is no needto record over material.

z To avoid confusion when erasing multiple tracks, youshould proceed in the order of high to low tracknumbers to prevent the renumbering of tracks that havenot been erased yet.

Example: Erasing B

1 While the recorder is stopped or during playbackpause, press EDIT/NO to display “Edit Menu.”

2 Turn AMS until “Erase?” appears in the display,then press AMS.

3 Turn AMS until the track number you want toerase appears in the display.

4 Press AMS or YES.When the track selected in Step 3 has beenerased, “Complete” appears for a few secondsand the total number of tracks in the musiccalendar decreases by one.

5 Repeat Steps 1 to 4 to erase more tracks.

To cancel the Erase FunctionPress EDIT/NO or p.

NoteIf “Erase???”appears in the display, the track was recordedor edited on another MD recorder and is record-protected.If this indication appears, press YES to erase the track.

1 2 3 4

1 2 3

A B C D

A C D

B is erased

Erasing all tracks on an MDYou can delete the disc name, all recorded tracks, andtitles of the recordable MD at once.


2 Turn AMS until “All Erase?” appears in thedisplay.

3 Press AMS or YES.“All Erase??” appears and all tracks in the musiccalendar start flashing.

4 Press AMS or YES again.When the disc name, all recorded tracks, and titleson the MD have been erased, “Complete” appearsfor a few seconds.

To cancel the Erase FunctionPress EDIT/NO or p and “All Erase?” or “All Erase??”disappears.

z You can undo the Erase FunctionSee “Undoing the Last Edit” on page 29.

Erasing a part of a trackBy using the Divide (see page 24), Erase (see page 22)and Combine (see page 25) Functions, you can erasespecific portions of a track.

Example: Erasing a part of track A

Tracknumber

Erasing

Part to be erased

A

4

A#1

A#2

A#3

2A#3

A#1 B

B

Tracknumber

B C

2 3

B C

C

A (#1+#3) C

3

3

5

31 2

1 2

1

1

Dividing

Erasing

Combining

A is dividedinto 3 parts

#1 and #3 arecombined

#2 iserased



24

Dividing Recorded Tracks(Divide Function)With the Divide Function you can assign a tracknumber at places that you want to randomly accessafterwards. Use this function to add tracks to MDsrecorded from an analog source (and therefore containno track numbers), or to divide an existing track intomultiple portions. When you divide a track, the totalnumber of tracks on the MD increases by one and alltracks following the divided track are renumbered.

Example: Dividing track 2 to create a new track for C

1Tracknumber

2 3

1

DCA

2 4

A B C D

B

Track 2 is divided and anew track is created for CDividing

3

4 While monitoring the sound, turn AMS to find thestarting position of the new track.The starting portion of the new track is playedback repeatedly.“Rehearsal“ alternates with “Position OK?“ in thedisplay.The starting position can be moved within amaximum range of –128 to +127 steps of about0.06 seconds within a track.

5 Press YES or AMS when the position is correct.When the track has been divided, “Complete”appears for a few seconds and the newly createdtrack begins playing. The new track will have notrack title even if the original track was labeled.

To cancel the Divide FunctionPress p or EDIT/NO.

z You can undo a track divisionCombine the tracks again (see “Combining RecordedTracks” on page 25) then redivide the tracks ifnecessary.

z You can divide a track while recordingUse the Track Marking Function (see page 12).

1 While playing the MD, press P at the point whereyou want to create a new track.The recorder pauses playing.

2 Press EDIT/NO to display “Edit Menu.”

3 Turn AMS until “Divide?” appears in the display,then press AMS.“Rehearsal” alternates with “Position OK?“ in thedisplay, the track to be divided starts flashing inthe music calendar, and the starting portion of thenew track begins playing repeatedly. (If thestarting position is correct, proceed with Step 5.)

≠AMS±

EDIT/NO YES

pP

25


Combining Recorded Tracks(Combine Function)Use the Combine Function while the recorder isstopped, playing or in pause to combine consecutivetracks on a recorded MD. This function is useful forcombining several songs into a single medley, orseveral independently recorded portions into a singletrack. When you combine two tracks, the total numberof tracks decreases by one and all tracks following thecombined tracks are renumbered.

Example: Combining B and C

1 2 3 4

A B C

A B C D

Tracknumber

D

1 2

CombiningB and C are combinedinto one track

3

To cancel the Combine FunctionPress EDIT/NO or p.

z You can undo a track combinationDivide the tracks again (see “Dividing RecordedTracks” on page 24), then repeat the combine functionwith the correct tracks if necessary.

NoteIf “Impossible” appears in the display, the tracks cannot becombined. This sometimes happens when you’ve edited thesame track many times, and is due to a technical limitationof the MD system, not a mechanical error.


2 Turn AMS until “Combine?” appears in thedisplay, then press AMS.

3 Turn AMS until the number of the former track ofthe two to be combined appears in the display,then press AMS.“Rehearsal“ alternates with “Track OK?“ in thedisplay. The place where the two tracks will join(i.e., the end of the former track and the beginningof the latter track) repeatedly plays back.

4 If the track is the wrong one, press EDIT/NO orp, then start again from Step 1.

5 If the place is correct, press AMS or YES.When the tracks have been combined,“Complete” appears for a few seconds.If both of the combined tracks have track titles,the title of the latter track is erased.

≠AMS±

EDIT/NO YES

p


26

Moving Recorded Tracks(Move Function)Use the Move Function to change the order of anytrack. After you move a track, the track numbersbetween the new and old track positions areautomatically renumbered.

Example: Moving track C to track position 2

1 2 3 4

1 4

Tracknumber

3

A B C D

A C B D

2Moving


2 Turn AMS until “Move?” appears in the display,then press AMS.

3 Turn AMS until the track number you want tomove appears in the display, then press AMS.

4 Turn AMS until the new track position appears.

5 Press AMS or YES.After you have moved the track, “Complete”appears for a few seconds.

To cancel the Move FunctionPress EDIT/NO or p.

Labeling Recordings(Title Function)You can create titles for your recorded MDs and tracks.Titles — which may consist of uppercase andlowercase letters, numbers and symbols for amaximum of about 1,700 characters per disc — appearin the display during MD operation.

Use the following procedure to label a track or an MD.You can label a track during play, pause, record, orstop mode. If the track is playing or recording, besure to finish labeling before the track ends. If thetrack ends before you’ve completed the labelingprocedure, only the characters already entered arerecorded automatically.

1 Press EDIT/NO to display “Edit Menu.”

2 Turn AMS until “Name in?” appears in thedisplay, then press AMS.

3 Turn AMS to select “Disc” or track number, thenpress AMS.When you label an MD, select “Disc” and whenyou label a track, select the track number. Notethat during recording, the recorder changes tocharacter typing mode and a cursor startsflashing.

Track C moves totrack position 2

≠AMS±

EDIT/NO YES

p

EDIT/NO YES

≠AMS± =/+

27


6 Repeat Steps 4 to 5 until you have entered theentire title.

If you entered the wrong characterPress 0 or ) until the character to be corrected startsflashing, and repeat Steps 4 and 5 to enter the correctcharacter.

To erase a characterPress 0 or ) until the character to be erased startsflashing, then press EDIT/NO.

To enter a spacePress AMS or ) while the cursor is flashing.

7 Press YES.This completes the labeling procedure and thetitle appears on the left side of the display.

To cancel labelingPress p.

NoteYou cannot label a track or an MD while you are recordingover an existing track.

4 Turn AMS to select the character.

The selected character flashes.Letters, numbers, and symbols appear insequential order as you turn AMS.You can use the following symbols in titles: ! ” # $ % & ’ ( ) * + , – . / : ; < = > ? @ _ ` ˆ

5 Press AMS to enter the selected character.The cursor shifts rightward and waits for theinput of the next character.

(Continued)


28

Labeling tracks and MDs with the remote Z 4 Repeat Steps 2 and 3 until you have entered theentire title.

If you entered the wrong characterPress 0 or ) until the character to be correctedstarts flashing.Press CLEAR to erase the incorrect character, then enterthe correct one.

5 Press NAME again.The entered title appears on the left side of thedisplay window after the label has been recorded.

To cancel labelingPress p.

Changing an existing title Z

1 Press NAME, then do the following:

2 Keep pressing CLEAR (or EDIT/NO on therecorder) until the current title is erased.

3 Enter the new title.Carry out Steps 4 to 7 of “Labeling Recordings”on page 26, or Steps 2 to 4 of “Labeling tracks andMDs with the remote” on page 28.

4 Press NAME.

1 Press NAME repeatedly until a flashing cursorappears in the display, then do the following:

2 Select the character type as follows:

3 Enter one character at a time.After you enter a character, the cursor shiftsrightward and waits for the input of the nextcharacter.

Alphabet/numberbuttons

r

6

)0

+=

pP·

NAME

CHAR

CLEAR

NUMp

0/)

To label Make sure that the recorder is

A track Playing, pausing, recording the trackto be labeled, or stopped afterlocating the track to be labeled

An MD Stopped with no track numberappearing in the display

To select Press

Uppercase letters CHAR repeatedly until “SelectedAB” appears in the display

Lowercase letters CHAR repeatedly until “Selectedab” appears in the display

NUM repeatedly until “Selected12” appears in the display

Numbers

To change

A track title

Make sure that the recorder is

Playing, pausing the track whose titleis to be changed, or stopped afterlocating the track whose title is to bechanged

Stopped with no track numberappearing in the display

A disc name

29


Undoing the Last Edit(Undo Function)You can use the Undo Function to cancel the last editand restore the contents of the MD to the condition thatexisted before editing was done. Note, however, thatyou cannot undo an edit if you do any of the followingafter the edit:• Press the r button on the front panel.• Press the r button, the MUSIC SYNC button, or the

CD-SYNC STANDBY button on the remote.• Turn off the power or eject the MD.• Disconnect the AC power cord.


2 Turn AMS until “Undo?” appears in the display,then press AMS.“Undo?” does not appear if no editing has beendone.One of the following messages appears in thedisplay, depending on the type of editing to beundone:

3 Press YES again.“Complete” appears for a few seconds and thecontents of the MD are restored to the conditionthat existed before the edit.

To cancel the Undo FunctionPress EDIT/NO or p.

EDIT/NO YES

≠AMS±

Function of Control Terminal

Control terminal (CTRL-S)Mini jack type

When a system controller with CTRL-S terminal isconnected to the control terminal of this recorder,it can operate as a remote .

Control functionsThe system controller which is connected to the controlterminal operates the same as the supplied remoteRM-D7M.

NoteWhen the system controller is connected to the controljack, the remote can not be used because its infraredrays are stopped.

Additional Information

Editing done:

Erasing a single track

Erasing all tracks on an MD

Dividing a track

Combining tracks

Moving a track

Labeling a track or an MD

Changing an existing title

Message:

“Erase Undo ?”

“Divide Undo ?”

“Combine Undo”

“Move Undo ?”

“Name Undo ?”


30

Dimensions

Mounting the recorderThis recorder can be attached to a standard 19 inchrack (type EIA). After detaching the four feet on thebottom of the recorder, mount the recorder on the rack.

Unit: mm


31


Functions of REMOTE Terminals

RELAY REC/PLAY— Stereo mini-jack terminal

Where multiple recorders are hooked up together, afterthe first recorder has finished recording or playing,control signals are automatically transferred to thesecond recorder through the RELAY terminal to directit to start recording or playing.

Relay PlayAllows multiple recorders hooked up together torepeat continuously in sequence.

Recorders may be hooked up in a loop so they willrepeat continuously.

Cabling for Relay Play

Connect RELAY OUT of the first recorder and RELAYIN PLAY of the second recorder with a stereo mini-plug cable (such as RK-G136). Interconnect RELAYOUT and RELAY IN PLAY also when hooking up twoor more recorders together.

1 The first recorder starts playing.

2 When the first recorder finishes playing, thesecond recorder starts playing.

3 The third and subsequent connected by cabling totheir RELAY IN PLAY terminals start playing insequence as soon as the preceding recorders in thechain finish playing.

NoteThis recorder starts playing when it receives a relay controlsignal only when:• It is loaded with a playable MD.• It is stopped.• The Edit Menu or Setup Menu is not open.

If REPEAT is set, control signal output will besuppressed, disabling the relay play function.

Relay RecordAllows multiple recorders hooked up together torecord continuously in sequence.

Cabling for Relay Record

Connect RELAY OUT of the first recorder and RELAYIN REC of the second recorder with a stereo mini-plugcable (such as RK-G136). Interconnect RELAY OUTand RELAY IN REC also when hooking up two ormore recorders together.

ToMixer

From divideequipment




32

1 The first recorder starts recording.

2 When the first recorder finishes recording, thesecond recorder starts recording.

3 The third and subsequent connected by cabling totheir RELAY IN REC terminals start recording insequence as soon as the preceding recorders in thechain finish recording.

If the display is set to show the remaining disc time(see page 16) during relay recording, a relay controlsignal is issued when the remaining recording time isreduced to about 6 seconds, thereby makingoverlapped recording possible on the first and secondrecorders.

When a recorder starts recording on receiving a controlsignal from the RELAY IN REC terminal, its display isautomatically set to show the remaining disc time.

NoteThis recorder starts recording when it receives a relaycontrol signal only when:• It is loaded with a recordable MD.• If digital input signal has been selected, digital audio

signal output from the source is available.• It is stopped.• The Edit Menu or Setup Menu is not open.

Relay recording always takes place in NewTrackRecmode.

Relay recording while clearing prerecorded discs is notavailable with this recorder.

Parallel I/O— D-sub 9 pins (female)

The parallel I/O pins permit remote control withsimple external circuits connected. The input pins,when connected to GND, implement the functionsassigned to them. The output terminals are opencollector outputs, which can be used to turn on LEDs toprovide recorder status indications.

Sample I/O pin circuits

<Sample output circuit> <Sample input circuit>

The Setup Menu allows you to select between defaults(PRESET) and user settings (USER).

The table below gives the relationship between the pinI/O and default functions.

Output pins(pins 7 to 9)

GND(pin 6)

GND(pin 6)

MDS-E11 Input pins(pins 1 to 5)

Pin No.

1

2

3

4

5

6

7

8

9

I/O

Input

Input

Input

Input

Input

–

Output

Output

Output

Function

PLAY/PAUSE

REC

STOP

AMS+

AMS–

GND

REC

PLAY

PAUSE

Setup Menu Name

PIN1

PIN2

PIN3

PIN4

PIN5

POUT1

POUT2

POUT3


33


With user settings (USER), PIN1 to PIN5 and POUT1 toPOUT3 in the Setup Menu can be assigned thefunctions in the table below. Each pin has fixed I/Ostatus.

PIN1 to PIN5 (Input pins)

POUT1 to POUT3 (Output pins)

Electrical Specifications

Input Terminal

Output Terminal

RS-232C— D-sub 9 pins (male)

The recorder can be externally controlled from a PC orsimilar equipment. For control protocols, consult yourdealer.

POWER ON

POWER OFF

POWER ON/OFF

(/P

PLAY

PAUSE

STOP

REC

AMS+

AMS–

FF

REW

EJECT

M.SYNC

T.REC

OFF

Turns on power. Not functional whenalready on.

Turns off power. Not functional whenalready off.

Turns power on and off.

Performs a play or pause operation.

Performs the same function as therecorder’s PLAY key.

Performs the same function as therecorder’s PAUSE key.

Performs the same function as therecorder’s STOP key.

Performs the same function as therecorder’s REC key.

Performs the same function as giving 1click clockwise turn to AMS.

Performs the same function as giving 1click counterclockwise turn to AMS.

Performs the same function as therecorder’s FF key.

Performs the same function as therecorder’s REW key.

Performs the same function as therecorder’s EJECT key.

Performs the same function as the remotecontroller’s M.SYNC.

Performs the same function as the remotecontroller’s T.REC.

Performs nothing.

POWER

REC

PLAY

PAUSE

NO DISC

OFF

Grounded when the power is on.

Grounded when the recorder’s RECindicator lights.

Grounded when the recorder displays (.

Grounded when the recorder displays P.

Grounded when the recorder is on and isnot loaded with a MD.

Left constantly floating.

Input method:

Input on voltage:

Input off voltage:

Open terminal voltage:

Input pulse width:

Input withstand voltage:

Make contact

0.5 V or less

3 V or more

3 V

100 msec or more

–0.5 to +10 V

Output method:

On-time residual voltage:

On-time maximum inflowcurrent:

Withstand voltage:

NPN transistor open collector

0.5 V or less

100 mA

20 V


34

Display MessagesThe following table explains the various messages thatappear in the display.

System LimitationsThe recording system in your MiniDisc recorder isradically different from those used in cassette and DATrecorders and is characterized by the limitationsdescribed below. Note, however, that these limitationsare due to the inherent nature of the MD recordingsystem itself and not to mechanical causes.

“Disc Full” lights up even before the MD has reached themaximum recording time (60 or 74 minutes)When 255 tracks have been recorded on the MD, “Disc Full”lights up regardless of the total recorded time. More than255 tracks cannot be recorded on the MD. To continuerecording, erase unnecessary tracks or use anotherrecordable MD.

“Disc Full” lights up before the maximum number oftracks is reachedFluctuations in emphasis within tracks are sometimesinterpreted as track intervals, incrementing the track countand causing “Disc Full” to light up.

The remaining recording time does not increase evenafter erasing numerous short tracksTracks under 12 seconds in length are not counted and soerasing them may not lead to an increase in the recordingtime.

Some tracks cannot be combined with othersTrack combination may become impossible when tracks areedited.

The total recorded time and the remaining time on theMD may not total the maximum recording time (60 or74 minutes)Recording is done in minimum units of 2 seconds each, nomatter how short the material. The contents recorded maythus be shorter than the maximum recording capacity. Discspace may also be further reduced by scratches.

Tracks created through editing may exhibit sound dropoutduring search operations.

Track numbers are not recorded correctlyIncorrect assignment or recording of track numbers mayresult (1) when CD tracks are divided into several smallertracks during digital recording, or (2) while recording certainCDs with the “LEVEL-SYNC” on (i.e., the automatic trackmarking function on.)

Meaning

A new (blank) or erased MD has beeninserted.

An attempt was made to make a secondcopy from a digitally dubbed MD (seepage 38.)

An attempt was made to edit the MDduring Program, Shuffle, or Normal Play.

The connected digital sound source isturned off or the recorder is not connectedproperly to the sound source.

Defected MD is inserted.

The MD is full (see “System Limitations”on this page.)

You cannot record or edit the MD due tothe system limitations.

The titling capacity of the MD has reachedits limit (about 1,700 characters.)

There is no MD in the recorder.

The inserted MD has a disc title but notracks.

The inserted MD is record-protected.

The first recording attempt failed due to adisturbance or scratch on the MD, and asecond attempt is being made.

Due to vibrations to the recorder orscratches on the MD, several recordingattempts were made but with no success.

The contents previously recorded are notsaved correctly on the MD, or the programcreated by Program Play is not stored inthe recorder’s memory.

Message

Blank Disc

Cannot Copy

Cannot EDIT

Din Unlock

Disc Error

Disc Full

Impossible

Name Full

No Disc

No Track

Protected

Retry

Retry Error

STANDBY(flashing)


35


“TOC Reading” appears for a long time“TOC Reading” will be displayed for longer than normalwhen an MD containing many songs is loaded.

Limitations when recording over an existing track• The correct remaining recording time may not be

displayed.• You may find it impossible to record over a track if that

track has been recorded over several times already. If thishappens, erase the track using the Erase Function (seepage 20.)

• The remaining recording time may be shortened out ofproportion to the total recorded time.

• Recording over a track to eliminate noise is notrecommended since this may shorten the duration of thetrack.

• You may find it impossible to label a track while recordingover it.

The correct recorded/playing time may not be displayedduring playback of monaural-format MDs.

TroubleshootingIf you experience any of the following difficulties whileusing the recorder, use this troubleshooting guide to helpyou remedy the problem. Should any problem persist,consult your nearest Sony dealer.

The recorder does not operate or operates poorly./The MD may be damaged (“Disc Error” appears.)

Take the MD out and insert it again. If “Disc Error”remains, replace the MD.

The recorder does not play back./Moisture has formed inside the recorder. Take the

MD out and leave the recorder in a warm place forseveral hours until the moisture evaporates./The recorder is not on. Press U to turn the recorder

on./The MD is inserted in the wrong direction. Slide the

MD into the disc compartment with the label side upand the arrow pointing towards the opening untilthe recorder grips it./The MD may not be recorded. Replace the disc with

one that has been recorded.

The recorder does not record./The MD is record-protected (“Protected” appears.)

Close the record-protect slot (see page 7.)/The recorder is not connected properly to the sound

source. Make connections properly to the soundsource./The recording level is not adjusted properly (in case

of input through LINE (ANALOG) IN.) Turn RECLEVEL to adjust the recording level properly (seepage 11.)/A premastered MD is inserted. Replace it with a

recordable MD./There is not enough time left on the MD. Replace it

with another recordable MD with fewer recordedtracks, or erase unnecessary tracks./There has been a power failure or the AC power

cord has been disconnected during recording. Datarecorded to that point may be lost. Repeat therecording procedure.

The recorder does not work during synchro-recording./The currently selected CD player type (CD player or

video CD player) does not match the CD playerbeing used. Reset the CD player type (see page 14.)

The sound has a lot of static./Strong magnetism from a television or a similar

device is interfering with operations. Move therecorder away from the source of strong magnetism.

NoteIf the recorder does not operate properly even after you’veattempted the prescribed remedies, turn off the power, thenreinsert the plug into the power outlet.


36

Specifications

System MiniDisc digital audio system

Disc MiniDisc

Laser Semiconductor laser (λ = 780 nm)Emission duration: continuous

Laser output Less than 44.6 µW** This output is the value measured at a

distance of 200 mm from the objectivelens surface on the Optical Pick-upBlock with 7 mm aperture.

Laser diode properties Material: GaAlAs

Revolutions (CLV) 400 rpm to 900 rpm

Error correction Advanced Cross Interleave ReedSolomon Code (ACIRC)

Sampling frequency 44.1 kHz

Coding Adaptive Transform Acoustic Coding(ATRAC)

Modulation system EFM (Eight-to-Fourteen Modulation)

Number of channels 2 stereo channels

Frequency response 5 to 20,000 Hz ±0.5 dB

Signal-to-noise ratio Over 92 dB during playback

Wow and flutter Below measurable limit

General

Power requirements Refer to warning letter.

Power consumption European models: 15WUSA models: 14W

Dimensions (approx.) (w/h/d) incl. projecting parts482 × 44 × 376 mm(19 × 1 3/4 × 14 7/8 in.)

Mass (approx.) 5.3 kg (11 lbs 11 oz)

Supplied accessories See page 4.

Optional accessoriesWired/Wireless remote unit: RM-D5MECoaxial digital connecting cable: VMC-10, etc.Recordable MDs: MDW-60 (60 min), MDW-74 (74 min)Relay record/playback connecting cable (such as RK-G136)

U.S. and foreign patents licensed from Dolby LaboratoriesLicensing Corporation.

Design and specifications are subject to change withoutnotice.

Inputs

Outputs

0.5Vp-p±20%

75 ohms

–4 dBu

Referenceinput

Maximuminput

Inputimpedance

47 kilohms

Jack type

Phono jacksANALOG(UNBAL) IN

—DIGITALCOAXIAL IN

Phono jacks

ANALOG(BAL) IN

XLR3-31equivalent

30 kilohms +4dBu +24dBu

+12 dBu

Load impedanceJack type Reference output

DIGITALCOAXIALOUT

75 ohms0.5Vp-p(at 75 ohms)

Phonojacks

0 dBu = 0.775 Vrms

ANALOG(BAL) OUT

XLR3-32equivalent

Maximum+24/+10 dBu(Switchable)

Over 600 ohms

PHONES 32 ohms0–10 mWThe level varies.

Stereophone jack

ANALOG(UNBAL)OUT

Over 10 kilohmsMaximum+8 dBu

Phonojacks


37


1 U (power) switch

2 Disc compartment

3 REC indicator

4 TOC incicator

5 Display

6 EDIT/NO button

7 YES button

8 0/) (fast forward/rewind) buttons

9 INPUT selector

0 REC LEVEL control

Index of Parts and Controls

!¡ PHONE LEVEL control

!™ Remote sensor

!£ § EJECT button

!¢ AMS control

!∞ P (pause) button

!§ p (stop) button

!¶ · (play) button

!• r (record) button

!ª PHONES jack


38

Guide to the Serial CopyManagement SystemThis MD recorder uses the Serial Copy ManagementSystem, which allows only first-generation digitalcopies to be made of premastered software via therecorder’s digital input jack. An outline of this systemappears below:

1 You can record from digital program sources (CDs, DATsor premastered MDs) onto a DAT tape or recordable MDvia digital input jack on the DAT or MD recorder.You cannot, however, record from this recorded DAT tapeor MD onto another DAT tape or recordable MD via thedigital input jack on the DAT or MD recorder.

MD recorder

DAT recorderCD player

Digital output jack

Digital input jack

v

vDAT recorder or

MD recorder

First-generationDAT tape or MDrecorded viadigital-to-digitalconnection

DAT or MD

DAT recorder orMD recorder

Digital output jack Line (analog) output jacks


Digital input jack Line (analog) input jacks

2 You can record the digital input signal of a digital satellitebroadcast onto a DAT tape or recordable MD via thedigital input jack on the DAT or MD recorder which iscapable of handling a sampling frequeny of 32 kHz or 48kHz. You can then record the contents of this recordedDAT tape or MD (first-generation) onto another DAT tapeor recordable MD via digital input jack on the DAT or MDrecorder to create a second-generation digital copy.Subsequent recording from the second-generation copyonto another recordable DAT tape or MD is possible onlythrough the analog input jack on the DAT or MD recorder.Note, however, that on some BS tuners, second-generationdigital copying may not be possible.

Playing

digital connectingcable

Recording DAT recorder orMD recorder


Playback

Recording DAT recorder orMD recorder

v

v

v

Digital input jack

Digital output jack

Digital input jack

digitalconnecting cable

DAT or MD

Second-generation DATtape or MDrecorded viadigital-to-digitalconnection

Playback DAT recorder orMD recorder

v


Audio connectingcord



DAT or MD

BS tuner

Playing

Playing

Recording


Recording


Digital output jack Line (agalog) output jacks

Recording

Digital input jack Line (analog) input jacks


Digital output jack

(Continued)


39


3 You can record a DAT tape or MD recorded via the DATor MD recorder’s analog input jack onto another DAT tapeor MD via the DAT or MD recorder’s digital output jack.You cannot, however, make a second-generation DATtape or MD copy via the DAT or MD recorder’s digitaloutput jack.

MD recorder

CD player

TunerTurntable

Cassette recorder

DAT recorder

Line (analog)output jacks

Audio connecting cord

Recording

v

vPlaying

Recording

v

vPlaying

Digital input jack

Digital output jack




RecordingDAT recorder or

MD recorder


Microphoneamplifier

DAT or MD


DAT or MD


Line (analog) output jacks

Line (analog) input jacks

Digital output jack

Digital input jack



Playing

Line (analog)input jacks

DAT tape or MDrecorded viaanalog-to-digitalconnection


40

Documents

MiniDisc Recorder · consult your nearest Sony dealer. Welcome! Thank you for purchasing the Sony MiniDisc Recorder. Before operating the recorder, please read this manual thoroughly