MIDWAY COMMUNITY CENTER

692 7TH AVENUE

MIDWAY, BC

ISSUED FOR REVIEW

OCTOBER 10, 2017

HB-

WH-

W-

CA-

N-

up

HB-

WH-

W-

CA-

N-

10

10

DRAWING NOTES APPLY WHERE INDICATED:

1. BEAM OVER.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. BUILDING GAS SERVICE AND METER.

15. CLEAN-OUT AT GRADE. REFER TO DETAIL.

16. RUN PIPE AT 2% SLOPE WHERE INDICATED BY DRAWINGNOTE.

17. IRRIGATION WATER SERVICE.

18. ROUGH-IN HOT, COLD, WASTE AND VENT PIPING IN WALLFOR FUTURE FIXTURE.

19. PROVIDE 1-1/2" TRAPPED WASTE AND 1/2" VALVED HOTWATER SUPPLY TO SUIT DISHWASHER.

20. PROVIDE NEW CONDENSATE ACID NEUTRALIZER. RUN 1-1/4"DRAIN LINE TO FLOOR DRAIN. 2 BOILER CONNECTIONS PERACID NEUTRALIZER.

21. GAS PRV (FROM 2 psi TO 7" wc) C/W ISOLATION VALVE.PROVIDE PRV VENT AS PER GAS CODE.

22. GAS SUPPLY UP TO ROOF MOUNTED EQUIPMENT. REFER TODETAIL.

23. EXTEND DOMESTIC WATER SERVICE TO THIS POINT ANDDISTRIBUTE HOT AND COLD SUPPLY TO EACH FIXTURE INTHE ROOM.

24. 3" BUILDING VENT.

25. EXACT LOCATION OF DOMESTIC HOT AND COLD WATER TOBE DETERMINED IN FIELD.

26. SANITARY AND DOMESTIC WATER SERVICES INSTALLEDTIGHT TOGETHER.

27. SYSTEM 15 PVC.

28. DISCHARGE FORCE MAIN INTO TOP OF GRAVITY MAIN.

29. ISLAND VENT.

30. NEW 2 PSI FORTIS NATURAL GAS METER. COORDINATE WITHFORTIS FOR REPLACEMENT.

31. SLAB ELEVATION 100' - 0"

32. RUN 1" CONDENSATE DRAIN LINE TO FUNNEL FLOOR DRAIN.

33. SOLENOID VALVE TO CONNECT TO KITCHEN FIRESUPPRESSION SYSTEM.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

up

9

24

28

PD-1

FFD-1FFD-1

FFD-1

30

LV-1WC-1FD-1LV-1

WC-1UR-1FD-1

MS-1

FD-1

27

L-1W-1FD-1

S-1

29

31

2020

20

HB-1

HB-1

HB-1

33

DRAWING NOTES APPLY WHERE INDICATED:

1. BEAM OVER.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. BUILDING GAS SERVICE AND METER.

15. CLEAN-OUT AT GRADE. REFER TO DETAIL.

16. RUN PIPE AT 2% SLOPE WHERE INDICATED BY DRAWINGNOTE.

17. IRRIGATION WATER SERVICE.

18. ROUGH-IN HOT, COLD, WASTE AND VENT PIPING IN WALLFOR FUTURE FIXTURE.

19. PROVIDE 1-1/2" TRAPPED WASTE AND 1/2" VALVED HOTWATER SUPPLY TO SUIT DISHWASHER.

20. PROVIDE NEW CONDENSATE ACID NEUTRALIZER. RUN 1-1/4"DRAIN LINE TO FLOOR DRAIN. 2 BOILER CONNECTIONS PERACID NEUTRALIZER.

21. GAS PRV (FROM 2 psi TO 7" wc) C/W ISOLATION VALVE.PROVIDE PRV VENT AS PER GAS CODE.

22. GAS SUPPLY UP TO ROOF MOUNTED EQUIPMENT. REFER TODETAIL.

23. EXTEND DOMESTIC WATER SERVICE TO THIS POINT ANDDISTRIBUTE HOT AND COLD SUPPLY TO EACH FIXTURE INTHE ROOM.

24. 3" BUILDING VENT.

25. EXACT LOCATION OF DOMESTIC HOT AND COLD WATER TOBE DETERMINED IN FIELD.

26. SANITARY AND DOMESTIC WATER SERVICES INSTALLEDTIGHT TOGETHER.

27. SYSTEM 15 PVC.

28. DISCHARGE FORCE MAIN INTO TOP OF GRAVITY MAIN.

29. ISLAND VENT.

30. NEW 2 PSI FORTIS NATURAL GAS METER. COORDINATE WITHFORTIS FOR REPLACEMENT.

31. SLAB ELEVATION 100' - 0"

32. RUN 1" CONDENSATE DRAIN LINE TO FUNNEL FLOOR DRAIN.

33. SOLENOID VALVE TO CONNECT TO KITCHEN FIRESUPPRESSION SYSTEM.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

dn

SK-4

29

SK-4

FD-1MS-2

FD-1

SK-2

LV-1WC-1UR-1FD-1

LV-1WC-1FD-1

SK-316

32FFD-1

DRAWING NOTES APPLY WHERE INDICATED:

1. BEAM OVER.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. BUILDING GAS SERVICE AND METER.

15. CLEAN-OUT AT GRADE. REFER TO DETAIL.

16. RUN PIPE AT 2% SLOPE WHERE INDICATED BY DRAWINGNOTE.

17. IRRIGATION WATER SERVICE.

18. ROUGH-IN HOT, COLD, WASTE AND VENT PIPING IN WALLFOR FUTURE FIXTURE.

19. PROVIDE 1-1/2" TRAPPED WASTE AND 1/2" VALVED HOTWATER SUPPLY TO SUIT DISHWASHER.

20. PROVIDE NEW CONDENSATE ACID NEUTRALIZER. RUN 1-1/4"DRAIN LINE TO FLOOR DRAIN. 2 BOILER CONNECTIONS PERACID NEUTRALIZER.

21. GAS PRV (FROM 2 psi TO 7" wc) C/W ISOLATION VALVE.PROVIDE PRV VENT AS PER GAS CODE.

22. GAS SUPPLY UP TO ROOF MOUNTED EQUIPMENT. REFER TODETAIL.

23. EXTEND DOMESTIC WATER SERVICE TO THIS POINT ANDDISTRIBUTE HOT AND COLD SUPPLY TO EACH FIXTURE INTHE ROOM.

24. 3" BUILDING VENT.

25. EXACT LOCATION OF DOMESTIC HOT AND COLD WATER TOBE DETERMINED IN FIELD.

26. SANITARY AND DOMESTIC WATER SERVICES INSTALLEDTIGHT TOGETHER.

27. SYSTEM 15 PVC.

28. DISCHARGE FORCE MAIN INTO TOP OF GRAVITY MAIN.

29. ISLAND VENT.

30. NEW 2 PSI FORTIS NATURAL GAS METER. COORDINATE WITHFORTIS FOR REPLACEMENT.

31. SLAB ELEVATION 100' - 0"

32. RUN 1" CONDENSATE DRAIN LINE TO FUNNEL FLOOR DRAIN.

33. SOLENOID VALVE TO CONNECT TO KITCHEN FIRESUPPRESSION SYSTEM.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

10

10

DRAWING NOTES APPLY WHERE INDICATED:

1. BEAM OVER.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TO SUITNEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. GOOSENECK ON ROOF.

15. GAS PRV (FROM 2 psi TO 7" wc) C/W ISOLATION VALVE.CONNECT TO ROOF TOP HEATING UNIT. REFER TO DETAIL.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

up

182

232323 23 2323

23

23

23

23

27

25

25

28

18

3232

32

10

10

DRAWING NOTES APPLY WHERE INDICATED:

1. REFER TO DETAIL FOR REQUIRED VALVING ARRANGEMENT.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. DUCT IN JOIST SPACE.

15. DUCT TIGHT TO UNDERSIDE OF STRUCTURE IN CEILINGSPACE.

16. ALL DUCT RUNOUTS TO DIFFUSERS ARE TO BE DIFFUSERNECK SIZE UNLESS OTHERWISE INDICATED.

17. PROVIDE MANUAL VOLUME DAMPER. PROVIDE ACCESS ASREQUIRED.

18. MOUNT GRILLE 8" ABOVE FLOOR LEVEL.

19. DUCT UP TO GOOSENECK ON ROOF.

20. MOUNT AT HIGH LEVEL.

21. PROVIDE BACKDRAFT DAMPER AT BUILDING ENVELOPEPENETRATION. REFER TO SPEC.

22. PROVIDE TRANSITION FOR DUCT UNDER BEAM.

23. ELECTRIC HEAT.

24. GRAVITY BACKDRAFT DAMPER.

25. PROVIDE FIRE DAMPER AT FIRE SEPARATION.

26. RE-BALANCE EXISTING GRILLE OR DIFFUSER TO NEWSPECIFIED AIR FLOW.

27. NEW SEWAGE LIFE STATION, SEE PLUMBING FOR DETAILS.

28. COMBUSTION AIR AND VENTS TO BE DUCTED TO ROOF.DUCT ROUTING SHOWN ON LOW LEVEL MECHANICAL ROOMPLAN.

29. UNDERCUT DOOR.

30. NFPA 96 KITCHEN EXHAUST HOOD.

31. FIRE RATED FURRING.

32. ACCESS PANEL.

33. CONFIRM JOIST SPACING TO DETERMINE RELIEF GRILLE CONFIGURATION/ SIZE TO NOT CONFLICT WITH STRUCTURE.

34. INSTALL ACOUSTIC INSULATION FOR FIRST 5FT AFTER WALLPENETRATION.

35. REQUIRES 42"x42" HOUSEKEEPING PAD. REFER TOSTRUCTURAL FOR DETAILS.

36. REQUIRES 54"X200" HOUSEKEEPING PAD. REFER TOSTRUCTURAL FOR DETAILS.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

dn

23

23

2831

31

14 14 14

14 14 1420

18

23

23

29

31

30

25

25

25

25

31

25

25

25

2532

32

32

32

21

21

33

34

32

35

36

35353535

10

10

DRAWING NOTES APPLY WHERE INDICATED:

1. REFER TO DETAIL FOR REQUIRED VALVING ARRANGEMENT.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. DUCT IN JOIST SPACE.

15. DUCT TIGHT TO UNDERSIDE OF STRUCTURE IN CEILINGSPACE.

16. ALL DUCT RUNOUTS TO DIFFUSERS ARE TO BE DIFFUSERNECK SIZE UNLESS OTHERWISE INDICATED.

17. PROVIDE MANUAL VOLUME DAMPER. PROVIDE ACCESS ASREQUIRED.

18. MOUNT GRILLE 8" ABOVE FLOOR LEVEL.

19. DUCT UP TO GOOSENECK ON ROOF.

20. MOUNT AT HIGH LEVEL.

21. PROVIDE BACKDRAFT DAMPER AT BUILDING ENVELOPEPENETRATION. REFER TO SPEC.

22. PROVIDE TRANSITION FOR DUCT UNDER BEAM.

23. ELECTRIC HEAT.

24. GRAVITY BACKDRAFT DAMPER.

25. PROVIDE FIRE DAMPER AT FIRE SEPARATION.

26. RE-BALANCE EXISTING GRILLE OR DIFFUSER TO NEWSPECIFIED AIR FLOW.

27. NEW SEWAGE LIFE STATION, SEE PLUMBING FOR DETAILS.

28. COMBUSTION AIR AND VENTS TO BE DUCTED TO ROOF.DUCT ROUTING SHOWN ON LOW LEVEL MECHANICAL ROOMPLAN.

29. UNDERCUT DOOR.

30. NFPA 96 KITCHEN EXHAUST HOOD.

31. FIRE RATED FURRING.

32. ACCESS PANEL.

33. CONFIRM JOIST SPACING TO DETERMINE RELIEF GRILLE CONFIGURATION/ SIZE TO NOT CONFLICT WITH STRUCTURE.

34. INSTALL ACOUSTIC INSULATION FOR FIRST 5FT AFTER WALLPENETRATION.

35. REQUIRES 42"x42" HOUSEKEEPING PAD. REFER TOSTRUCTURAL FOR DETAILS.

36. REQUIRES 54"X200" HOUSEKEEPING PAD. REFER TOSTRUCTURAL FOR DETAILS.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

2328

DRAWING NOTES APPLY WHERE INDICATED:

1. REFER TO DETAIL FOR REQUIRED VALVING ARRANGEMENT.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. DUCT IN JOIST SPACE.

15. DUCT TIGHT TO UNDERSIDE OF STRUCTURE IN CEILINGSPACE.

16. ALL DUCT RUNOUTS TO DIFFUSERS ARE TO BE DIFFUSERNECK SIZE UNLESS OTHERWISE INDICATED.

17. PROVIDE MANUAL VOLUME DAMPER. PROVIDE ACCESS ASREQUIRED.

18. MOUNT GRILLE 8" ABOVE FLOOR LEVEL.

19. DUCT UP TO GOOSENECK ON ROOF.

20. MOUNT AT HIGH LEVEL.

21. PROVIDE BACKDRAFT DAMPER AT BUILDING ENVELOPEPENETRATION. REFER TO SPEC.

22. PROVIDE TRANSITION FOR DUCT UNDER BEAM.

23. ELECTRIC HEAT.

24. GRAVITY BACKDRAFT DAMPER.

25. PROVIDE FIRE DAMPER AT FIRE SEPARATION.

26. RE-BALANCE EXISTING GRILLE OR DIFFUSER TO NEWSPECIFIED AIR FLOW.

27. NEW SEWAGE LIFE STATION, SEE PLUMBING FOR DETAILS.

28. COMBUSTION AIR AND VENTS TO BE DUCTED TO ROOF.DUCT ROUTING SHOWN ON LOW LEVEL MECHANICAL ROOMPLAN.

29. UNDERCUT DOOR.

30. NFPA 96 KITCHEN EXHAUST HOOD.

31. FIRE RATED FURRING.

32. ACCESS PANEL.

33. CONFIRM JOIST SPACING TO DETERMINE RELIEF GRILLE CONFIGURATION/ SIZE TO NOT CONFLICT WITH STRUCTURE.

34. INSTALL ACOUSTIC INSULATION FOR FIRST 5FT AFTER WALLPENETRATION.

35. REQUIRES 42"x42" HOUSEKEEPING PAD. REFER TOSTRUCTURAL FOR DETAILS.

36. REQUIRES 54"X200" HOUSEKEEPING PAD. REFER TOSTRUCTURAL FOR DETAILS.

23

28

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

DRAWING NOTES APPLY WHERE INDICATED:

1 FURNACE.

2 FILTER PLENUM ACCESS FROM FRONT.

3 OUTDOOR AIR CONNECTION.

4 MOTORIZED DAMPER.

5 MANUAL DAMPER.

6 SUPPORT FRAME.

7 FLEXIBLE CONNECTION.

8 CONDENSATE DRAIN C/W DEEP SEAL TRAP (1"Ø).

9 ACOUSTIC INSULATION.

5496

7

22

8 8

9

4

5

9

7 7

1 1

7 3

6

1. SUPPLY DIFFUSER C/W OPPOSED BLADE DAMPER..

DRAWING NOTES APPLY WHERE INDICATED:

1. BRANCH DUCT SIZE IS DIFFUSER NECK SIZE.

2.

3.

4.

5.

6.

FLEX. MAXIMUM 1.5 DUCT DIAMETER.

MIN. THREE DUCT DIA. OF STRAIGHT DUCT.

STRAIGHT TEE FOR THIS APPLICATION ONLY.

ONE DUCT DIA.

DIFFUSER - SEE SPEC. FOR SIZE AND TYPE.

DRAWING NOTES APPLY WHERE INDICATED:

7.

8.

9.

BUTTERFLY DAMPER.

ELBOW FOR THIS APPLICATION ONLY.

EQUALIZING GRID AS REQUIRED BY BALANCINGAGENT OR ENGINEER AT TIME OF BALANCING.

NOTED2 AND D3 = TOD1 - 125 OR LESS

THAN D1-100mmD1 OR NOT LESSD2 AND D3 = TONOTE

RADIUS BRANCH TAKE-OFFRADIUS BRANCH TAKE-OFF

MAX. SLOPE25mm IN 100mm

W1xD1 W2xD2

R1=3/4 W3

R2=1 3/4 W3 W3xD3W3xD3

W2xD2W1xD1

R2=1 3/4 W3

TRANSITION FITTINGS

RECTANGULAR TO RECTANGULAR

RECTANGULAR TO ROUND

MAX. SLOPE25mm IN 100mm

25mm IN 100mmMAX. SLOPE

RADIUS ELBOW SQUARE ELBOW

CONSTRUCTION OF 45° ELBOWS

W

WW

R= W

W

CONSTRUCTION OF 90° ELBOWS

SEE DETAILTURNING VANES

TURNING VANE DETAIL

30mm

25mm

50mm

ELBOWS.PERMIT RADIUSCONDITIONS DO NOTSHOWN OR SPACEWHERE 90° ELBOWS AREUSE THIS DESIGN

W

PLANELBOW SHOWN ONWHERE RADIUS USE THIS DESIGN

W

SQUARE ELBOWRADIUS ELBOW

W

R= W

W

R

R1=3/4 W3B

150mm

A

L

REDUCER

25mm

45° LATERAL

C150mm

25mm

L

A

SLIP JOINT STOP BEAD

-

-

-

-

L

R

C

B

DIA. 250mm & OVER - L=100mmDIA. 75mm - 225mm - L=50mmSTOP BEAD.LENGTH OF MALE ENDS BEYOND

RADIUS.

BRANCH TAKE-OFF DIAMETER.

REDUCING.MAIN BARREL OUTLET DIAMETER IF

MAIN BARREL INLET DIAMETER.-A

CONICAL TEE

25mm25mm

C

L

A

SLIP JOINT STOP BEAD

SLIP JOINT STOP BEAD

R

A

L

R=1.5A R=1.5A

L

A

R

SLIP JOINT STOP BEAD

R=1.5A

L

R

SLIP JOINT STOP BEAD

DIE STAMPED 90° SEGMENTAL 90° SEGMENTAL 45°

AJOINTS AND DRAIN CONNECTION.

10 CONCRETE HOUSEKEEPING PAD OR SUPPORT

9 24 GA. G.I. DRAIN PAN C/W SOLDERED

HOT WATER HEATER. REFER TO SCHEDULE.

HOSE END DRAIN VALVE.

DIELECTRIC UNION (TYP.).

RESEATING P & T RELIEF VALVE.

VACUUM RELIEF VALVE.

-

OF CHECK VALVE .DRILL 1.5mm HOLE IN FLAPPER

8

7

6

5

4

3

2

1

PLATFORM.

SEE DRAWINGS FOR ACTUAL LOCATION OF HOTWATER HEATER, DRAIN LOCATION, RECIRCULATIONPUMP PIPING MAINS AND SIZES.

11

RUN PAN DRAIN CONNECTION TO DRAIN.

DRAWING NOTES APPLY WHERE INDICATED:

HEAT TRAP LOOP.12

4

7

8

9

111

12

13 EXPANSION TANK.

14 DISCHARGE TO HUB DRAIN OR FUNNEL FLOORDRAIN.

5

13

14

14" MINIMUMCURB

FINISHED FLOOR LEVEL

CEILING

ROOF

KITCHEN EXHUAST HOOD

GREASE TRAP

HINGED COWL

CLEARANCES SHALL BE INTEGRAL WITH HOOD

DRAWING NOTES APPLY WHERE INDICATED:

1

2

ADD NFPA-96 APPROVED FIRE RATED DUCT WRAP ANDINSTALL AS PER SPECIFICATIONS.

3

4

WIRING BY DIV. 20 (WEATHERPROOF EXTERNAL TO AIR STEAM &FLEXIBLE

WELDED KITCHEN EXHAUST DUCT (16 Ga. Min.)

WEATHERPROOF DISCONNECT

KITCHEN EXHAUST FAN (FAN & DUCTWORK SHALL CONFORM TOTHE LATEST NFPA-96 REQUIREMENTS)

VENTILATED CURB SECTION

A MINIMUM CLEARANCE OF 1000 (40") MUST BE PROVIDEDBETWEEN THE ROOF AND THE FAN DISCHARGE.

DUCTS TO BE WELDED LIQUID/AIR TIGHT, REFER TOSPECIFICATION FOR DUCT GAUGE REQUIREMENTS. DUCTS MUSTEXTEND A MINIMUM OF 450 (18") ABOVE ROOF SURFACE.

MINIMUM AIR VELOCITY THROUGH ALL DUCTS IS 1500 FPM, WITH AMAXIMUM OF 2500 FPM.

KITCHEN EXHAUST FAN WIRING TO BE EXTERNAL (WIRING MUSTNOT BE INSTALLED IN THE AIRSTREAM)

INSTALLATION MUST INCLUDE MEANS FOR INSPECTING, CLEANING,AND SERVICING THE EXHAUST FAN.

5

6

7

8

9

10

11

12

13

14

15

16

6

8

9

10

1112

13

14

PROVIDE NON-COMMBUSTIBLE CEILING OR STAINLESS STEELPANELS TO 457mm (18") FROM DUCTWORK AND HOOD.

FIRE SUPPRESSION SYSTEM BY OTHERS.

15

16

17 ACCESS DOOR CLEANOUTS AS PER NFPA 96.

6

9

3

7

6

54

2

1

3

2

7

1

8

7

1

6

3

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

1 GRADE OR PAVING.

2 CAST IRON CLEANOUT WITH COVERFOR DUTY REQUIRED.

3 150 THICK CONCRETE PAD.

4 SEWER PIPE.

5 45° BEND.

6 SEWER MAIN.

7 FROM BUILDING DRAIN.

DRAWINGS NOTES APPLY WHERE INDICATED:

76

5

4

1 2 3

DRAWING NOTES APPLY WHERE INDICATED:

1 HINGED ACCESS DOOR.

2 TOP RAIL SUPPORT BOLTED TO COVER FRAME.

3 LIFTING CHAIN.

4 JUNCTION BOX.

5 3" INLET PIPE.

6

7

GATE VALVE.

8

SWING CHECK VALVE.

9

10

DISCHARGE PIPING.

VERTICAL PIPE GUIDE RAILS AS REQUIRED.

11

SUBMERSIBLE NON-CLOG PUMP.

12

13

BOTTOM OF BASIN MUST HAVE SMOOTH

15

14

LIFT-OUT ASSEMBLY.

TROWELED SURFACE FOR MOUNTING OF THE SUPPORT CASTING.

4" (100mm)

ALARM LEVEL.

TURN ON ONE PUMP.

TURN OFF ONE PUMP.

2 1/2" VENT.

8"(200mm)

8"(200mm)

48"(1200mm)

4" (100mm)

4" (100mm)

16

17

INLET LEVEL.

13

14

15

16

12

1110

9

8

7 7

6 6

8

5 5

4

33

2

1 1

17

STORM COLLAR (TYP.)

CONE FLASHINGBELOW STORMCOLLAR (TYP.)

STORM COLLAR

ROOF JACK

TOP VIEW

SIDE VIEW

VENT

CAP FLASHING OVERTOP OF CONE FLASHING

VENT

COMBINATION AIR INLET

COMBINATION AIR INLET

DRAWING NOTES APPLY WHERE INDICATED:

1 HANGER ROD.

2 LOCK NUT.

3 SUPPORT NUT.

4 HEAVY DUTY CLEVIS HANGER.

5 VAPOUR BARRIER INSULATION.

6 INSULATION WHERE SPECIFIED BUTT AGAINST PIPE HANGER.

7 16 GA ZINC COATED SHEET METAL PIPE COVERING PROTECTIONSADDLE. LENGTH SHALL BE AT LEAST TWICE THE OUTSIDEDIAMETER OF THE INSULATION BUT NOT LESS THAN 300mm LONG.

NOTE:COPPER PIPING SHALL BE SUPPORTED BYCOPPER PLATED HANGERS. SEE SPEC.

CLEVIS HANGERHORIZONTAL PIPE RUNW/ VAPOUR BARRIERINSULATION INSULATION

NO VAPOUR BARRIERHORIZONTAL PIPE RUNCLEVIS HANGER

7

65

44 3

3

2

2

11

6" (150mm)

18

14" (350mm)

DISTANCE TO STORAGE.18

ROOF

CAULKJOINTS

(TYP)

MINIMUM 18"CLEARANCE

SHEET METAL HOUSING

CAP FLASHING OVERTOP OF CONE FLASHING

28" (700mm)19

DISTANCE TO TOP OF TANK.19

DRAWING NOTES APPLY WHERE INDICATED:

1 STRAP OR THREADED ROD.

2 DUCT.

3 CONTINUOUS STRAP.

1

2

3

DRAWING NOTES APPLY WHERE INDICATED:

2 LOCKABLE BALL VALVE ON BYPASS LINE(NORMALLY CLOSED).

3 PRESSURE GUAGE (TYPICAL).

4 UNION (TYPICAL).

5 GATE VALVE (TYPICAL).

6 DRAIN VALVE.

7 FUNNEL FLOOR DRAIN.

8 1" WATER METER.

9 DOUBLE CHECK VALVE ASSEMBLY FOR PREMISE

10 1" CAPPED CONNECTION FOR FUTURE IRRIGATION.

23

4 5

6

7

89

ISOLATION. CROSS CONNECTION PROTECTIONTO FOLLOW CSA STANDARDS.

1

1 TO DCW SYSTEM.

11 MAIN SHUT OFF VALVE.

11

10

2

11

DRAWING NOTES APPLY WHERE INDICATED:

1 CONCRETE SLAB.

2 1/8" SLOTS CUT IN TO BOTTOM OF RADON VENT PIPE. SLOTS TO BECUT THE FULL LENGTH OF ALL PIPE INSTALLED BELOW GRADE.

DRAWING NOTES APPLY WHERE INDICATED:

1 DISCHARGE OF STACK TO BE 25' (7.6M) AWAY FROM ANY AIR INTAKE.

2

RADON EXHAUST FAN RF-1. 3

4

5

1

2

3

5

6

REFER TO ARCHITECTURAL FOR ALL ROOFPENETRATION, MEMBRANE AND FLASHING DETAILS

CONNECT FAN TO PIPE WITH RUNNER PIPE CONNECTORS.

6

2

4

6" (150mm) SYSTEM 15 PVC PIPE. PROVIDE WARNING LABELINDICATING "WARNING, STACK MAY CONTAIN HIGH LEVELSOF RADON. DO NOT PLACE AIR INTAKE WITHIN 25 FEET."

24"

(600

mm

)18

"(4

50m

m)

SUPPORT BY MECHANICAL INCLUDING EDPM BOOT, SECURED WITHDRAW BAND AND POLYURETHANE SEALANT WHERE REQUIRED.

GOOSENECK C/W BIRDSCREEN7

7

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

7

7

7 7

777

7

7

7

7 7 7 7

7

7 7 7

7

DRAWING NOTES APPLY WHERE INDICATED:

1. BEAM OVER.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. BUILDING GAS SERVICE AND METER.

15. CLEAN-OUT AT GRADE. REFER TO DETAIL.

16. RUN PIPE AT 2% SLOPE WHERE INDICATED BY DRAWINGNOTE.

17. IRRIGATION WATER SERVICE.

18. ROUGH-IN HOT, COLD, WASTE AND VENT PIPING IN WALLFOR FUTURE FIXTURE.

19. PROVIDE 1-1/2" TRAPPED WASTE AND 1/2" VALVED HOTWATER SUPPLY TO SUIT DISHWASHER.

20. PROVIDE NEW CONDENSATE ACID NEUTRALIZER. RUN 1-1/4"DRAIN LINE TO FLOOR DRAIN. 2 BOILER CONNECTIONS PERACID NEUTRALIZER.

21. GAS PRV (FROM 2 psi TO 7" wc) C/W ISOLATION VALVE.PROVIDE PRV VENT AS PER GAS CODE.

22. GAS SUPPLY UP TO ROOF MOUNTED EQUIPMENT. REFER TODETAIL.

23. EXTEND DOMESTIC WATER SERVICE TO THIS POINT ANDDISTRIBUTE HOT AND COLD SUPPLY TO EACH FIXTURE INTHE ROOM.

24. 3" BUILDING VENT.

25. EXACT LOCATION OF DOMESTIC HOT AND COLD WATER TOBE DETERMINED IN FIELD.

26. SANITARY AND DOMESTIC WATER SERVICES INSTALLEDTIGHT TOGETHER.

27. SYSTEM 15 PVC.

28. DISCHARGE FORCE MAIN INTO TOP OF GRAVITY MAIN.

29. ISLAND VENT.

30. NEW 2 PSI FORTIS NATURAL GAS METER. COORDINATE WITHFORTIS FOR REPLACEMENT.

31. SLAB ELEVATION 100' - 0"

32. RUN 1" CONDENSATE DRAIN LINE TO FUNNEL FLOOR DRAIN.

33. SOLENOID VALVE TO CONNECT TO KITCHEN FIRESUPPRESSION SYSTEM.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

7

7

7

7

DRAWING NOTES APPLY WHERE INDICATED:

1. BEAM OVER.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. BUILDING GAS SERVICE AND METER.

15. CLEAN-OUT AT GRADE. REFER TO DETAIL.

16. RUN PIPE AT 2% SLOPE WHERE INDICATED BY DRAWINGNOTE.

17. IRRIGATION WATER SERVICE.

18. ROUGH-IN HOT, COLD, WASTE AND VENT PIPING IN WALLFOR FUTURE FIXTURE.

19. PROVIDE 1-1/2" TRAPPED WASTE AND 1/2" VALVED HOTWATER SUPPLY TO SUIT DISHWASHER.

20. PROVIDE NEW CONDENSATE ACID NEUTRALIZER. RUN 1-1/4"DRAIN LINE TO FLOOR DRAIN. 2 BOILER CONNECTIONS PERACID NEUTRALIZER.

21. GAS PRV (FROM 2 psi TO 7" wc) C/W ISOLATION VALVE.PROVIDE PRV VENT AS PER GAS CODE.

22. GAS SUPPLY UP TO ROOF MOUNTED EQUIPMENT. REFER TODETAIL.

23. EXTEND DOMESTIC WATER SERVICE TO THIS POINT ANDDISTRIBUTE HOT AND COLD SUPPLY TO EACH FIXTURE INTHE ROOM.

24. 3" BUILDING VENT.

25. EXACT LOCATION OF DOMESTIC HOT AND COLD WATER TOBE DETERMINED IN FIELD.

26. SANITARY AND DOMESTIC WATER SERVICES INSTALLEDTIGHT TOGETHER.

27. SYSTEM 15 PVC.

28. DISCHARGE FORCE MAIN INTO TOP OF GRAVITY MAIN.

29. ISLAND VENT.

30. NEW 2 PSI FORTIS NATURAL GAS METER. COORDINATE WITHFORTIS FOR REPLACEMENT.

31. SLAB ELEVATION 100' - 0"

32. RUN 1" CONDENSATE DRAIN LINE TO FUNNEL FLOOR DRAIN.

33. SOLENOID VALVE TO CONNECT TO KITCHEN FIRESUPPRESSION SYSTEM.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

DRAWING NOTES APPLY WHERE INDICATED:

1. REFER TO DETAIL FOR REQUIRED VALVING ARRANGEMENT.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. DUCT IN JOIST SPACE.

15. DUCT TIGHT TO UNDERSIDE OF STRUCTURE IN CEILINGSPACE.

16. ALL DUCT RUNOUTS TO DIFFUSERS ARE TO BE DIFFUSERNECK SIZE UNLESS OTHERWISE INDICATED.

17. PROVIDE MANUAL VOLUME DAMPER. PROVIDE ACCESS ASREQUIRED.

18. MOUNT GRILLE 8" ABOVE FLOOR LEVEL.

19. DUCT UP TO GOOSENECK ON ROOF.

20. MOUNT AT HIGH LEVEL.

21. PROVIDE BACKDRAFT DAMPER AT BUILDING ENVELOPEPENETRATION. REFER TO SPEC.

22. PROVIDE TRANSITION FOR DUCT UNDER BEAM.

23. ELECTRIC HEAT.

24. GRAVITY BACKDRAFT DAMPER.

25. PROVIDE FIRE DAMPER AT FIRE SEPARATION.

26. RE-BALANCE EXISTING GRILLE OR DIFFUSER TO NEWSPECIFIED AIR FLOW.

27. NEW SEWAGE LIFE STATION, SEE PLUMBING FOR DETAILS.

28. COMBUSTION AIR AND VENTS TO BE DUCTED TO ROOF.DUCT ROUTING SHOWN ON LOW LEVEL MECHANICAL ROOMPLAN.

29. UNDERCUT DOOR.

30. NFPA 96 KITCHEN EXHAUST HOOD.

31. FIRE RATED FURRING.

32. ACCESS PANEL.

33. CONFIRM JOIST SPACING TO DETERMINE RELIEF GRILLE CONFIGURATION/ SIZE TO NOT CONFLICT WITH STRUCTURE.

34. INSTALL ACOUSTIC INSULATION FOR FIRST 5FT AFTER WALLPENETRATION.

35. REQUIRES 42"x42" HOUSEKEEPING PAD. REFER TOSTRUCTURAL FOR DETAILS.

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"

DRAWING NOTES APPLY WHERE INDICATED:

1. REFER TO DETAIL FOR REQUIRED VALVING ARRANGEMENT.

2. BULKHEAD OR FURRING.

3. CAP FOR FUTURE.

4. EXISTING TO REMAIN IN SERVICE.

5. EXISTING TO BE ABANDONED. REMOVE AS REQUIRED TOSUIT NEW CONSTRUCTION.

6. EXISTING TO BE RELOCATED.

7. EXISTING TO BE REMOVED.

8. CAP EXISTING IN THIS APPROXIMATE LOCATION.

9. CONNECT TO EXISTING IN THIS APPROXIMATE LOCATION.

10. PVC SYSTEM 15 RADON EXHAUST PIPE. CONNECT TO PIPEPROVIDED BY THE GENERAL TRADE AND TERMINATE WITHGOOSENECK ON THE ROOF.

11. FOR CONTINUATION, SEE SITE SERVICES.

12. ROOF ACCESS.

13. CEILING ACCESS.

14. DUCT IN JOIST SPACE.

15. DUCT TIGHT TO UNDERSIDE OF STRUCTURE IN CEILINGSPACE.

16. ALL DUCT RUNOUTS TO DIFFUSERS ARE TO BE DIFFUSERNECK SIZE UNLESS OTHERWISE INDICATED.

17. PROVIDE MANUAL VOLUME DAMPER. PROVIDE ACCESS ASREQUIRED.

18. MOUNT GRILLE 8" ABOVE FLOOR LEVEL.

19. DUCT UP TO GOOSENECK ON ROOF.

20. MOUNT AT HIGH LEVEL.

21. PROVIDE BACKDRAFT DAMPER AT BUILDING ENVELOPEPENETRATION. REFER TO SPEC.

22. PROVIDE TRANSITION FOR DUCT UNDER BEAM.

23. ELECTRIC HEAT.

24. GRAVITY BACKDRAFT DAMPER.

25. PROVIDE FIRE DAMPER AT FIRE SEPARATION.

26. RE-BALANCE EXISTING GRILLE OR DIFFUSER TO NEWSPECIFIED AIR FLOW.

27. NEW SEWAGE LIFE STATION, SEE PLUMBING FOR DETAILS.

28. COMBUSTION AIR AND VENTS TO BE DUCTED TO ROOF.DUCT ROUTING SHOWN ON LOW LEVEL MECHANICAL ROOMPLAN.

29. UNDERCUT DOOR.

30. NFPA 96 KITCHEN EXHAUST HOOD.

31. FIRE RATED FURRING.

32. ACCESS PANEL.

33. CONFIRM JOIST SPACING TO DETERMINE RELIEF GRILLE CONFIGURATION/ SIZE TO NOT CONFLICT WITH STRUCTURE.

34. INSTALL ACOUSTIC INSULATION FOR FIRST 5FT AFTER WALLPENETRATION.

35. REQUIRES 42"x42" HOUSEKEEPING PAD. REFER TO

210-1715 Dickson Ave. Kelowna, BC V1Y 9G6250.762.9993 www.falcon.ca

4' 3' 2' 1'

12'8'4'0

SCALE: 1/4"=1'-0"