Mewar University Chittorgarh (Rajasthan) Civil Syllabus.pdf · BS-103 Engineering Mathematics-I 3 1 - 4.0 35 15 50 100 BS-105 Engineering Chemistry 3 1 - 4.0 35 15 50 100 ES-101 Engineering

Mewar University Chittorgarh (Rajasthan)

MEWAR UNIVERSITY CHITTORGARH

(RAJASTHAN)

Faculty of Engineering and Technology

SCHEME, CURRICULUM AND SYLLABUS

Four – Year (Regular) B Tech: Civil Engineering

Syllabus as perPOargdein1anofce1; Effective from 2011-12 Printing Cost: Rs.50


B Tech: Civil Engineering

MEWAR UNIVERSITY CHITTORGARH

(RAJASTHAN)


SCHEME AND CURRICULUM


Effective from 2011-12



Foreword

The following syllabi contain paper-wise teaching and examination schemes for the

three courses mentioned below:

(a) B.Tech (4Yrs)

(b) B.Tech - M.Tech Integrated (5 Yrs)

(c) B.Tech - M.B.A. Integrated (5 Yrs)

This syllabi presented here shall be treated as final, and no change or amendment can

be made to the syllabi without the prior written consent of the syllabus expert

committee appointed by the Hon'ble Chairperson and approved by the Academic

Council.

The syllabus presented herewith shall form the basis for teaching both theory and

practical classes. The faculty is expected to teach, guide and supervise students on all

aspects of the syllabus so that the entire range of syllabus is covered for all papers

within their respective semesters.

Students must attend the lectures, tutorials and practical classes on topics stipulated in

the syllabus. Under no circumstances any complaints related to topics not taught shall

be entertained during the mid-term / end-term University examinations.

The examination shall consist of dual method of evaluation, comprising:

a) Subjective type questions: These questions will cover the entire syllabus for

each paper to test the basics and in-depth knowledge of the students on the

topics (Mid-term Examinations).

b) Objective type questions: These questions will cover the entire syllabus for

each paper to test as well as help prepare students for competitive exams.

These questions shall be of the standard of Gate / IES / Other related

competitive examinations. The students are required to prepare accordingly

(End Term Examinations).

All the courses shall have a mandatory 21-45 days on-the-job training at the end of the

Sixth Semester to be certified by the concerned Industrial house / body; covering a

credit of 6 to be included in the SGPA / CGPA.



Contents

Section A

Curriculum and Scheme of Examination 1-11

Section B

Syllabus Common 1st and 2nd Semester 12-39

Section C

Syllabus 3rd to 8th Semester 40-114


B Tech: Civil Engineering Page 1

MEWAR UNIVERSITY CHITTORGARH (RAJASTHAN)


SCHEME AND CURRICULUM


Effective from 2011-12



Category/Terminology used:

BS = Basic Sciences #includes Mathematics, Physics and Chemistry courses; ES = Engineering Arts and Sciences #includes Fundamental Engineering courses;

HS = Humanities, Social science and Management #to provide a wide exposure to different areas of Humanities, Social science and

Management; CE = Civil Engineering #includes core courses of Civil Engineering and elective courses offered by the parent department to provide an

opportunity to the student to specialize significantly in one sub area of Civil Engineering*; OE = Open Electives to provide an opportunity to the student to develop interdisciplinary knowledge base or to specialize significantly

in an area outside Mechanical Engineering**; ELGA = English Language and General Awareness***.

* There are sixteen (16) elective courses offered by the department to provide wider choices and flexibility to the students to cater to their academic interests. The student will have to choose any four out of these.

** There are ten (10) open elective courses offered by the other departments out of which the student will have to choose any two out

of these.

*** One Course on English Language and General Awareness in each semester has been included with a definite objective; students should be encouraged to acquire a certain level of language proficiency and general awareness that are necessary to nurture them into competent professionals.

In addition to above six hours per week to be spent on sports activities, NSS, NCC, social responsibilities, computer skills and programming, technical activities (quizzes, workshops, invited talks on emerging topics, extra classes, make up classes, industrial visits etc.)

Requisite weightage has been provided to all categories of the courses with an objective of holistic academic development of the students. The total credits for the programme will be 220 distributed to all above categories.



First Semester (Common to all Disciplines)

Course Code

Course Title

Contact Hours per week

Credit Hours

Internal Assessment/Evaluation External

Examination /Viva-voce

Total Marks

L T P Assignments/

Lab Record Teachers’ Evaluation

BS-101 Engineering Physics-I 3 1 - 4.0 35 15 50 100

BS-103 Engineering Mathematics-I 3 1 - 4.0 35 15 50 100

BS-105 Engineering Chemistry 3 1 - 4.0 35 15 50 100

ES-101 Engineering Graphics & Drawing 1 3 - 4.0 35 15 50 100

ES-103 Fundamentals of Computers and Programming

3 1 - 4.0 35 15 50 100

ES-105 Basics of Electrical Engineering/ Basics of Electronics Engineering

3 1 - 4.0 35 15 50 100

BS-107 Physics Lab-I - - 2 1.0 15 10 25 50

BS-109 Chemistry Lab - - 2 1.0 15 10 25 50

ES-107 Computer Lab - - 2 1.0 15 10 25 50

ES-109 Electrical/ Electronics Engineering Lab

- - 2 1.0 15 10 25 50

ES-111 Workshop Practice-I - - 2 1.0 15 10 25 50

ELGA-101 English Language and General Awareness-I

1 - - 1.0 - - 25 25

17 08 10

Total Semester Marks=875 Total Semester Credits = 30.0



Second Semester (Common to all Disciplines)

Course Code

Course Title


Credit Hours


Examination

/Viva-voce

Total Marks

L T P Assignments/

Lab Record

Teachers’

Evaluation

BS-102 Engineering Physics-II 3 1 - 4.0 35 15 50 100

BS-104 Engineering Mathematics-II 3 1 - 4.0 35 15 50 100

ES-102 Introduction to Environmental Sciences

3 1 - 4.0 35 15 50 100

ES-104 Introduction to CADD 3 1 - 4.0 35 15 50 100

ES-106 Basics of Electronics Engineering/ Basics of Electrical Engineering

3 1 - 4.0 35 15 50 100

ES-108 Basics of Mechanical Engineering 3 1 - 4.0 35 15 50 100

BS-108 Physics Lab-II - - 2 1.0 15 10 25 50

ES-110 Electronics / Electrical Engineering Lab

- - 2 1.0 15 10 25 50

ES-112 Workshop Practice-II - - 2 1.0 15 10 25 50

ES-114 CAD Lab - - 2 1.0 15 10 25 50

HS-102 Language Lab - - 2 1.0 15 10 25 50

ELGA-102 English Language and General Awareness-II

1 - - 1.0 - - 25 25

19 06 10




Third Semester

Course Code

Course Title


Credit Hours


Examination

/Viva-voce

Total Marks

L T P Assignments/

Lab Record

Teachers’

Evaluation

CE-201 Structural Analysis-I 3 1 - 4.0 35 15 50 100

CE-203 Fluid Mechanics-I 3 1 - 4.0 35 15 50 100

CE-205 Surveying-I 4 - - 4.0 35 15 50 100

CE-207 Building Construction and Materials

3 1 - 4.0 35 15 50 100

CE-209 Design of Steel Structures-I 3 1 - 4.0 35 15 50 100

HS-201 Essentials of Management and Organizational Behavior

3 1 - 4.0 35 15 50 100

CE-211 Structural Mechanics Lab-I - - 2 1.0 15 10 25 50

CE-213 Fluid Mechanics Lab-I - - 3 1.5 25 15 35 75

CE-215 Surveying Lab-I - - 3 1.5 25 15 35 75

ELGA-201 English Language and General Awareness-III

1 - - 1.0 - - 25 25

20 05 08




Fourth Semester

Course Code

Course Title


Credit Hours


Examination

/Viva-voce

Total Marks

L T P Assignments/

Lab Record

Teachers’

Evaluation

CE-202 Structural Analysis-II 3 1 - 4.0 35 15 50 100

CE-204 Fluid Mechanics-II 3 1 - 4.0 35 15 50 100

CE-206 Surveying-II 3 1 - 4.0 35 15 50 100

CE-208 Design of Concrete Structures-I 3 1 - 4.0 35 15 50 100

CE-210 Concrete Technology 3 1 - 4.0 35 15 50 100

HS-202 Fundamentals of Business & Economics

3 1 - 4.0 35 15 50 100

CE-212 Concrete Lab - - 2 1.0 15 10 25 50

CE-214 Surveying Lab–II - - 3 1.5 25 15 35 75

CE-216 Fluid Mechanics Lab-II - - 3 1.5 25 15 35 75

ELGA-202 English Language and General

Awareness-IV 1 - - 1.0 - - 25 25

19 06 08




Fifth Semester

Course Code

Course Title


Credit Hours



Total Marks

L T P Assignments/


CE-301 Structural Analysis-III 3 1 - 4.0 35 15 50 100

CE-303 Transportation Engineering-I 3 1 - 4.0 35 15 50 100

CE-305 Hydrology and Water Power 3 1 - 4.0 35 15 50 100

CE-307 Soil Mechanics 3 1 - 4.0 35 15 50 100

CE-309 Project Planning & Management 3 1 - 4.0 35 15 50 100

CE-311 Environmental Engineering-I 3 1 - 4.0 35 15 50 100

CE-313 Computer Applications Lab - - 2 1.0 15 10 25 50

CE-315 Transportation Engineering Lab - - 2 1.0 15 10 25 50

CE-317 Soil Mechanics Lab - - 2 1.0 15 10 25 50

CE-319 Environmental Engineering Lab - - 2 1.0 15 10 25 50

ELGA-301 English Language and General Awareness-V

1 - - 1.0 - - 25 25

19 06 08




Sixth Semester

Course Code

Course Title


Credit Hours



Total Marks

L T P Assignments/


CE-302 Design of Steel Structures-II 3 1 - 4.0 35 15 50 100

CE-304 Geotechnology 3 1 - 4.0 35 15 50 100

CE-306 Transportation Engineering-II 3 1 - 4.0 35 15 50 100

CE-308 Environmental Engineering-II 3 1 - 4.0 35 15 50 100

CE-310 Irrigation Engineering 3 1 - 4.0 35 15 50 100

CE-312 Design of Concrete Structures-II 3 1 - 4.0 35 15 50 100

CE-314 Transportation Engineering Lab- II

- - 2 1.0 15 10 25 50

CE-316 Environmental Engineering Lab- II

- - 2 1.0 15 10 25 50

CE-318 Soil Mechanics Lab-II - - 2 1.0 15 10 25 50

CE-320 Seminar - - 2 1.0 25 25 - 50

ELGA-302 English Language and General Awareness-VI

1 - - 1.0 - - 25 25

19 06 08


All the courses shall have a mandatory 21-45 days on-the-job training at the end of the Sixth Semester to be certified by the

concerned Industrial house / body; covering a credit of 6 to be included in the SGPA / CGPA.



Seventh Semester

Course Code

Course Title


Credit Hours



Total Marks

L T P Assignments Teachers’ Evaluation

CE-421 Departmental Elective-I 3 1 - 4.0 35 15 50 100

CE-422 Departmental Elective-II 3 1 - 4.0 35 15 50 100

CE-423 Departmental Elective-III 3 1 - 4.0 35 15 50 100

CE-424 Departmental Elective-IV 3 1 - 4.0 35 15 50 100

OE-431 Open Elective-I 3 - - 3.0 25 - 50 75

OE-432 Open Elective-II 3 -

3.0 25 - 50 75

IT-001 Industrial Training (21-45 Days) - - 12 6.0 - - 150 150

18 04 12




Eighth Semester

Course Code

Course Title


Credit Hours

Internal Assessment/Evaluation

External


Total Marks

L

T

P Training/ Project Report

Teachers’ Evaluation

CE-441/442 Industrial Training/Project - - 40 20 150 100 250 500

CE-450 Comprehensive Academic and General Proficiency Viva-Voce

- - - 02 - - 50 50

- - 40




LIST OF DEPARTMENTAL ELECTIVES (16) CE-421/422/423/424

Quantity Survey and Valuation Finite Element Methods

Prestressed Concrete Structures Traffic Engineering

Ground Improvement Techniques Environmental Pollution Control

Solid and Hazardous Waste Management Hydraulic Structures

Hydro Power Engineering Retrofitting and Rehabilitation of Structures

Optimization Techniques for Civil Engineering Machine Foundations

Bridge Engineering Rock Mechanics

Highway & Airfield Pavement Design Structural Dynamics and Seismic Design

LIST OF OPEN ELECTIVES (10)

OE-431/432

Operations Management Renewable Energy Sources

Advanced Engineering Mathematics Consumer Electronics

Entrepreneurship Security in Computing

Soft Computing Modeling and Simulation

Artificial Intelligence

Remote Sensing & GIS

Microprocessors and Microcontrollers

Civil Engineering Estimating & Costing


B Tech: 1st & 2nd Semester - Civil Engineering Page 12

B TECH (1st SEMESTER)

BS-101 ENGINEERING PHYSICS-I

Internal Evaluation: 50 Marks External Examination: 50 Marks

Duration of Examination: 03 Hours

Course Objective:

The objective of teaching engineering physics is to give an understanding of the basic knowledge and impart quality education in physical sciences to the budding engineers. To strengthen the skills in basic measurements by exposing the students to well equipped labs and enhance the problem solving ability through interactive classes.

UNIT-I

Interference, Conditions for sustained interference, Coherent sources, Division of wave front, Fresnel’s biprism, Division of amplitude, Newton’s rings, Michelson’s interferometer and their applications.

Diffraction, Differences between Fraunhofer and Fresnel diffraction, Fraunhofer diffraction at a single slit, Plane transmission diffraction grating, Its dispersive and resolving powers.

Polarization, Polarized and unpolarized light, Double refraction, Nicol Prism, Theory for Production of Plane, Circular and Elliptical Polarized Light, Quarter and half wave plates, Polarimetry, Biquartz and Lauerent’s half-shade polarimeters.

UNIT-II

Laser, Spontaneous and stimulated emissions, Absorption, Einstein’s coefficients, Population inversion, Pumping, Laser action, Characteristics of Laser beam, Concept of coherence, Types of laser, He-Ne and semiconductor laser (simple ideas), Applications.

Fibre Optics, Optical Fibre, Structure and classification of optical fibre; Single mode and multimode fibres, Propagation of light in fibre, Numerical aperture and acceptance angle, Applications.

UNIT-III

Electromagnetic wave theory, Maxwell’s equations in Integral form, Maxwell’s equations in differential form and their physical significances, Simple plane wave equation, Poynting Vector, Physical significance, Poynting theorem.

Dielectrics, Molecular theory, Polarization, Displacement, Susceptibility, Dielectric coefficient, Permittivity and various relations between them, Gauss’s law in the presence of a dielectric, Energy stored in electrostatic field, Behaviour of dielectrics in ac fields-simple concepts, Dielectric losses.

UNIT-IV

Nuclear fission, Moderators, Nuclear reactors, Reactor criticality and neutron cross- section, Nuclear fusion, Interaction of radiation with matter (basic concepts), Radiation Detectors-ionization chamber, G M Counter, Scintillation and solid state detectors, Cloud chamber and bubble chamber.

Recommended Books:

Jackson J D, Classical Electrodynamics Jenkins and White, Fundamentals of optics, McGraw Hills Puri S, Modern Physics concepts and applications, Narosa Publishers Thyagrajan and Ghatak, Lasers- Theory and applications, McMillan Publishers Leo W R, Techniques for Nuclear and Particle Physics Experiments

L T P Cr

3 1 - 4




BS-103 ENGINEERING MATHEMATICS-I



Course Objective:

An effective knowledge of mathematics for all engineering students is a necessary requirement for the education of qualified engineering graduates capable both of innovation and of adaptation to changing technology. After completing the syllabus, Students can better understand the mathematical terms used to solve the engineering problems under different conditions.

UNIT-I

Applications of Differentiation, Taylor’s and Maclaurin’s series, Expansion by use of known series, Expansion by forming a differential equation, Asymptotes, Curvature. Radius of curvature for cartesian parametric and Polar curves, Centre of curvature and chord of curvature, Curve tracing (Cartesian and Polar curves).

UNIT-II

Exact differential equations, Equations reducible to exact differential equations, Simultaneous linear equations with constant co-efficients, Applications of differential equations of 1st order and 1st degree to simple electric circuits, Linear differential equations of higher order, Complete solutions, Complementary functions and particular integral, Applications of linear differential to oscillatory electric circuits. Formation of partial differential equations, Lagrange’s linear partial differential equations, 1st order non-linear partial differential equations, Charpit’s method.

UNIT-III

Rank of a matrix, Elementary transformation, Elementary matrices, Inverse using elementary transformations, Normal form of a matrix, Consistency of linear system of equations, Linear and orthogonal transformations, Eigen values and eigen vectors, Properties of Eigen values, Cayley-Hamilton Theorem and its applications.

UNIT-IV

Double integral, Change of order of integration Double integral in polar coordinates, Applications of double integral to find area enclosed by plane curves and volume of solids of revolution. Triple integral, Volume of solids, Change of variables, Beta and gamma functions and relationship.

Recommended Books:

Grewal B S, Higher Engineering Mathematics Sastry S S, Engineering Mathematics, Vol. I, Prentice Hall of India Piskunov, Differential and Integral Calculus Piaggio H T H, Differential Equations Jain R K and Iyengar S R K, Advanced Engineering Mathematics: Greenberg Michael D, Advanced Engineering Mathematics Sneddon I N, Elements of Partial Differential Equations

L T P Cr

3 1 - 4




BS-105 ENGINEERING CHEMISTRY



UNIT-I

Introduction to water treatment, Types of hardness, Units of Hardness, Degree of Hardness, Determination of Hardness by EDTA method, Boiler troubles, Scale and sludge formation, Caustic Embrittlement, Softening methods, Lime Soda process, Zeolite (Permutit process) process, Demineralization (Ion Exchange process), Desalination, BOD, COD and their significance, Surface water pollution and self purification, Waste water treatment, Sedimentation and biological methods.

UNIT-II

Introduction to Corrosion and its control, Causes and different types of corrosion and effects of corrosion, Theories of corrosion, Chemical, Electrochemical corrosion, Corrosion reactions, Factors affecting corrosion, Nature of metal, Galvanic series, Over voltage, Purity of metal, Nature of oxide film, Nature of corrosion product, Nature of environment-effect of temperature, Effect of pH, Humidity, Effect of oxidant, Corrosion control methods, Cathodic protection, Sacrificial anode, Impressed current cathode, Surface coatings, Methods of application on metals, Hot dipping, Galvanizing, Tinning, Cladding, Electroplating, Organic surface coatings, Paints constituents and functions.

Proximate and ultimate analysis of coal, Significance of the constituents, Gross and net calorific value, Determination of calorific value by Bomb calorimeter, Liquefaction and gasification.

UNIT-III

Types of Polymerization, Mechanism (Chain growth & Step growth), Thermoplastic resins & Thermo setting resins, Compounding & fabrication of plastics, Preparation, Properties, Engineering applications of: polyethylene, PVC, PS, Teflon, Bakelite, Nylon, Conducting Polymers, Poly acetylene, Polyaniline, Conduction, Doping, Applications, Liquid Crystal polymers, Characteristics and uses Rubber, Natural rubber, Vulcanization, Elastomers, Buna-s, Butyl rubber, Thiokol rubbers, Fibers, Polyester, Fiber reinforced plastics (FRP), Applications, Biodegradable polymers. Brief idea of super conductors, Organic electronic materials, Fullerenes and optical fibers.

UNIT-IV

Sources of petrochemicals, Classifications, CNG, Basic building blocks processes- thermal cracking (mechanism, Production of ethylene and co-products, Petrochemicals from ethylene and propylene) and catalytic reforming (mechanism, Production of BTX aromatics), Petrochemicals from BTX aromatics.

Portland cement, Manufacture of Portland cement by rotary kiln method, Chemistry of setting and hardening of cement. Refractories, Properties, Classification, Properties of silica and fireclay refractories.

Recommended Books:

Jain P C and Jain Monika, Engineering Chemistry Vermani O P and Narula A K, Applied Chemistry, Theory and Practice Peterwiseman, Petrochemicals Maiti Sukumar, Introduction to Petrochemicals, Chawla Shashi, A text book of Engineering Chemistry Kuriacase J C and Rajaram J, Engineering Chemistry

L T P Cr

3 1 - 4

Course Objective:




ES-101 ENGINEERING GRAPHICS & DRAWING



Course Objective:

The objective of this course is to accurately and unambiguously capture all the geometric features of a product or a component and convey all the required information that will allow a manufacturer to produce that component.

UNIT-I

Principles of Engineering Graphics and their Significance, Drawing Instruments and their Use, Conventions in Drawing, Lettering, BIS Conventions. Various types of lines, Dimensioning, Principles of dimensioning, Various types of lines and dimensioning exercises, Exercises on free hand lettering techniques.

Various types of projections, 1st and Third angle systems of orthographic projections, Orthographic projection of Points and line in different quadrants, Orthographic projections of lines for parallel, Perpendicular & inclined to horizontal and vertical Plane, Projections of lines inclined to both the Reference Planes, True and apparent lengths, True and apparent inclinations to reference planes, Traces.

UNIT-II

Projections of plane surfaces-triangle, Square rectangle, Rhombus, Pentagon, Hexagon and circle, Planes in different positions by change of position method only, Traces.

Projection of different solids like Cylinder, Cone, Pyramid, & Sphere with axis parallel, Perpendicular & inclined to both reference planes.

UNIT-III

Sectioning of solid: Introduction, Section planes, Sections, Section views, Sectional views, Apparent shapes and True shapes of Sections of right regular prisms, Pyramids, Cylinders and cones resting with base on HP.

Isometric and Perspective Projections: Types of Pictorial Projections – Isometric view and Isometric projection – Isometric Scale – Drawing Isometric Projection of Solid Objects (combination of two solids) - Perspective Projection – Terminology – Visual Ray Method – Vanishing Point method.

UNIT-IV

Development of surfaces: Development of surfaces of cylinders, Cones pyramids, Prisms etc. Exercises involving development of unique surfaces like Y- piece, Hopper, Tray, Truncated pieces etc.

Intersection of solid: Intersection of cylinders, Cones and prisms with their axes being vertical, Horizontal or inclined, Exercises on intersection of solids cylinder and cylinder, Cylinder and cone, Prism and prism, Prism and cone, Sphere with cylinder.

Recommended Books:

Bhatt N D, Engineering Drawing, Charotar Publishing House. Gill P S, Engineering Drawing, S K Kataria and Sons, Ludhiana. Shah M B and Rana B C, Engineering Drawing, Pearson Education. French T E and Vierck C J, Graphic Science, McGraw-Hill, New York Zozzora F, Engineering Drawing, McGraw Hill, New York Luzadder and Duff, Fundamental of Engineering Drawing, Prentice hall of India Pvt Ltd.

L T P Cr

1 3 - 4




ES-103 FUNDAMENTALS OF COMPUTERS AND PROGRAMMING



Course Objective:

To know the components of a Computer System, To understand basic Concepts of Operating System and Computer Networks, To have an overview of different types of operating systems like DOS, UNIX/LINUX Operating System, Windows XP, To have a thorough knowledge of various System Software and Programming languages, To study different kinds of Number system, To know the concepts of Problem Solving, To have a thorough knowledge of C language and its programming

UNIT-I

Brief history of development of Computers, Introduction to Digital System, Von Newman Concept, Hypothetical Decimal Computer, Hardware Organization of Computer System, Input /Output devices, Storage devices, Input /Output Ports and Connectors, Introduction to Operating Systems, Functions of Operating Systems, Classifications of Operating systems, Basic introduction to DOS, UNIX/LINUX Operating System, Windows XP.

Data Communication, Network Devices-LAN, LAN Topologies, WAN, OSI Reference model, Introduction to internet and Protocols: TCP/IP Reference model, Backbone Network, Network connecting devices, Hypertext documents, HTTP, DNS, Network security.

UNIT-II

System Software, Application Software, Programming languages, Machine language, Assembly language, Low level language, High level language, Types of high level language, Compiler, Interpreter, Assembler, Loader, Linker, Relationship between Compiler, Interpreter, Loader & Linker, Introduction to MS-OFFICE.

Number System, Binary System, Conversion between Number Bases, Binary Addition, Subtraction of 1’s Complement & 2’s Complement Method, Octal System, Hexadecimal System, Binary Coded Decimal, ASCII system

UNIT-III

Flowcharts & Algorithms, Problem Definition Phase, General Problem Solving Strategies, Top down, Breaking a Problem into sub Problems, Choice of a Suitable Data Structure, Documentation of Programs, Debugging of Programs.

Introduction to C, Preprocessor, Directives, Header files, Data Types & Qualifiers, Operators & Expressions, Enumerations Data input & output, Variables and arithmetic Expressions, The for statement, Symbolic Constant, Character Input and output, Arrays, Functions, Arguments- call by value, Character Arrays, External Variables and Scope, Types, Operators and Expressions: Variable Names, Data types and Sizes, Constants, Declarations, Arithmetic operators, Relational and logical operators, Type conversions Bitwise operator, Assignment operators and operators and expressions, Conditional ,expressions, Precedence and order of evaluation, Related exercises in C.

UNIT-IV

Statement and blocks, IF–else, Else–if, Switch, Loops- while and for, Loops –do – while, Break and continue, Goto and labels, Functions and program structure, Basics of functions, External variables, Scope rule, Header file, Static variables, Register variables, Block structure, Initialization, Recursion, Related exercises in C.

Pointers and addresses, Pointers and function arguments, Pointers and arrays, Address arithmetic, Character pointers and functions, Pointer arrays: pointers to pointers, Multi- dimensional arrays, Related exercises in C.

Basics of structure, Structures and functions, Arrays of structures, Pointers to

structure, Table lookup, Unions, Related exercises in C. Standard input and output, Formatted output-printf, Variable-length arguments list, Formatted input-scanf, File access, Line input and output, Related exercises in C.

L T P Cr

3 1 - 4



Recommended Books:

Rajaraman V, Computer programming in C, PHI

Sharma A K, Fundamental of Computers & Programming with C, Dhanpat Rai Publications, New Delhi

Kernighan Brian W and Ritchi Dennis, The C Programming Language, 2nd Edition, PHI

Gottfried B S, Programming in C, SCHAUM SERIES, TMH

Silberschatz Abraham, Baer Peter and Greg Galvin, Operating System Concepts, 7th Edition, John Wiley & Sons Inc




ES-105/106 BASICS OF ELECTRICAL ENGINEERING



Course Objective:

Students will be able to learn the fundamentals of Electrical Engineering in Circuit Analysis, Measurements & electrical machines. This will help students of all disciplines to understand the basics of Electrical Engineering.

UNIT-I

Introduction to linear and non linear circuits, Circuit elements, Various sources and source transformation, Star-delta transformation, Solution of DC circuits using Kirchoff's laws, Nodal and mess analysis, Signal wave forms, Network theorems: Thevenin’s, Norton, Maximum power transfer, Superposition, Millman’s theorems.

UNIT-II

AC sinusoidal voltage and currents, Average and rms values, Form factor and peak factor, Phasor representation, Phasor in polar, Rectangular and exponential forms, Terminal relationship for pure passive elements and their combination in series and parallel, Analysis of single phase series, Parallel and Series-parallel circuits, Active and reactive power, Pf and volt-amperes, Frequency response, Series/parallel resonance, Bandwidth, Q-factor, Analysis of balanced three phase AC Circuits, Voltage, Current and power in three phase balanced circuits, Wattmeter method to measure three phase power.

UNIT-III

Magnetic circuit concept, Dot representation, B-H curves characteristics of magnetic materials, Magnetic circuits, Laws for magnetic circuits, Magnetic circuits with DC and AC excitation, Hysteresis and eddy current losses Magnetic force, Self and mutual inductances, Faraday`s laws, Lenz`s Law, Statically and dynamically induced emfs Principle of Transformer operation, Construction details, Open circuit /short circuit tests, Equivalent circuit of transformer, Auto transformer operation, All day efficiency.

UNIT-IV

Introduction to galvanometer, Construction, Operation and uses of moving iron type and moving coil type, Induction type voltmeter, Ammeter, Watt meter, Energy meter, Use of shunt and multiplier.

Fundamentals of DC and AC machines, Types, Operating principle, Torque speed curves.

Recommended Books:

Alexander Charles K and Sadiku N O and Matthew, Fundamental of Electric Circuits, TMH Publication

Valkenberg, Linear Circuits, PHI Publication Toro Vincent Del, Electrical Engineering Fundamentals, PHI Publication Cotton H, Electric Technology, CBS Publishers and Distributors Fitzgerald A E, Basic Electrical Technology, McGraw Hill Publication Hughs, Electrical Technology, Pearson Ltd Arumugam M, And Premkumar N, Electric Circuit Theory, Khanna Publishers Kothari, Basic Electrical Engineering, TMH

L T P Cr

3 1 - 4




BS-107 PHYSICS LAB-I



EXPERIMENTS

To determine the refractive index of the material of a lens.

To find the wavelength of light by Fresnel’s biprism.

To find the wavelength of monochromatic light by using diffraction grating.

To verify Malus Law in polarization of light.

To find the wavelength of sodium light by measuring the diameters of Newton’s rings.

To find a) the wavelength of sodium light b) the thickness of a thin transparent sheet by Michelson’s interferometer.

To calibrate a voltmeter and an ammeter by using potentiometer.

To find the temperature coefficient of resistance of platinum by using platinum resistance thermometer.

To study the variation of magnetic field along the axis of a circular coil carrying current and to estimate the radius of the coil.

To find the frequency of AC mains using sonometer.

To plot a graph between the difference of temperature of two junctions and thermo emf for a thermocouple using a potentiometer.

To study the shunting effect of a voltmeter on voltage measurement.

To study the half life period of a given radioactive material using GM counter.

L T P Cr

- - 2 1




BS-109 CHEMISTRY LAB



EXPERIMENTS

Determination of total, Temporary and permanent hardness of given water sample by EDTA titration.

Determination of calcium and magnesium hardness of given water sample separately by EDTA titration.

Determination of alkalinity of given irrigation water sample.

Determination of DO of given water sample.

Determination of the available chlorine in bleaching powder suspension and to find out the chlorine demand of the given water sample.

Determination of calcium as calcium oxide volumetrically in given cement sample.

Preparation of phenol-formaldehyde, Urea –formaldehyde and cellulose- acetate resin.

Determination of acid value of oil.

Determination of saponification value of oil.

Determination of iodine value of oil.

Determination of flash point by Abel’s flash point apparatus and Pensky Marten’s Apparatus.

Determination of viscosity of lubricants by Redwood viscometer

(i) Conductometric and pH–metry determination of HCl with standard NaOH.

(ii) Conductometric and pH-metry determination of CH3COOH with standard NaOH.

Determination of the composition of a mixture of acetic acid and hydrochloric acid by conductometric and pH-metry method.

Recommended Books:

Vermani O P and Narula A K, Applied Chemistry Theory and Practice

Yadav J B, Practical Physical Chemistry

L T P Cr

- - 2 1




ES-107 COMPUTER LAB



EXPERIMENTS

Familiarization of the Operating System like DOS and Windows.

Loading window, Closing, Maximizing, Icon shifting & ordering.

Changing drives and searching files and understanding file extensions.

Saving files, Protecting and unprotecting.

Practice with control panel and file manager.

Practice with MS Word, Operating and closing document, Preparation of document, Setting of document, Familiarization with various tools, Mail- merge practice.

Internet Browsing.

Use of Spreadsheet to Create Charts (XY, Bar, Pie) & Apply formulae wherever necessary.

Implement the following programs using C language.

a Find greatest number among three numbers using conditional operators & if statement using C programming.

b Read two numbers & Swap those two numbers using temporary variable & without using temporary variable.

c Use of switch…case statements.

d Generation of prime and Fibonacci series.

e Matrix operations-addition, Transpose & multiplication.

f Use of structure to define a user defined data types input the data and write the data into file.

g Use of Pointers and Array of Pointers.

h Various Sorting and Searching Techniques.

i Program on Files for creating, Populating & manipulating a simple Database.

j Program on Recursive Functions.

Recommended Books:

Rajaraman C V Computer programming PHI

Sharma A K Fundamental of Computers & Programming with C, Dhanpat Rai Publications, New Delhi

Kernighan Brian W, Ritchi Dennis C Programming Language, 2nd Edition, PHI

Gottfried B S Programming in C, SCHAUM SERIES, TMH

L T P Cr

- - 2 1




ES-109/110 ELECTRICAL ENGINEERING LAB



EXPERIMENTS

To verify KCL and KVL.

To find responses and plot phasor diagrams for R-L, R-C, And R-L-C circuits.

To verify Thevenin's theorem.

To verify Maximum power transfer theorem in AC and DC circuits.

To verify Superposition theorem.

To study frequency response of a series R-L-C circuit and determine resonant frequency Obtain Q-factor and plot phasor diagram at resonance.

To perform OC/SC tests on a 1 phase transformer for parameter evaluations.

To perform load test on 1 phase transformer and plot efficiency Vs load characteristic.

To perform direct load test on a DC shunt generator and plot load voltage Vs load current curve.

To study various type of meters and measure energy consumption for a lamp load.

Measurement of power by 3 voltmeter/3 Ammeter method.

Measurement of power in a 3-phase system by two waltmeter method.

Recommended Book:

Kohli and Jain, Electrical Machines Fundamentals

L T P Cr

- - 2 1




ES-111 WORKSOP PRACTICE-I



Course Objective:

The main objective of the course is to make the engineering students familiar with the basic problems related to manufacturing which may come across during their career and their day to day life too.

EXPERIMENTS

To study different types of measuring tools used in metrology and determine least counts of Vernier callipers, Micrometers and Vernier height gauges.

To study different types of machine tools (lathe, Shape or planer or slotter, Milling, Drilling machines).

To prepare a job on lathe machine involving simple turning, Step turning, Facing, Parting off, Finishing, Thread cutting, Chamfering and drilling.

To study different types of fitting tools and marking tools used in fitting practice.

To prepare a job involving finishing of two sides of a square piece by filing.

To study different types of smithy and forging tools used in practice.

To prepare a job involving various smithy operations such as upsetting, Drawing down, Punching, Bending, Fullering & swaging.

To study different types of Arc welding along with its construction, Working and various tools used.

To prepare a simple lap and butt joint using Arc welding.

To study various types tools and apparatus used in foundry shop.

To prepare sand moulding using the pattern.

Recommended Book:

Saha, Workshop Practice, TMH

L T P Cr

- - 2 1




ELGA-101* ENGLISH LANGUAGE AND GENERAL AWARENESS -I

L T P Cr External Evaluation: 25 Marks 1 - - 1

Assumption:

The course is specifically designed for students from the rural background

who have studied in Hindi medium schools. The purpose is to fill in the

gaps in their knowledge which they may have due to lack of exposure and

to enrich their vocabulary and command over grammar.

Course Objective:

The course is specifically focused on laying a firm foundation for English language proficiency by helping students build a strong base in Grammar

and vocabulary.

Grammar And Vocabulary

Unit 1: Word skills

Unit 2: Tense, Active and Passive Voice Unit 3: Direct and Indirect Narration

Unit 4: Punctuation Unit 5: Common errors

Recommended Books:

Learning English, A Communicative Approach, Rama Krishna Rao, Orient Longman Private Limited, Hyderabad, 2008.

Improve Your Written English, Marion Field, Jaico Publishing House, New Delhi, 2006.

English for Empowerment, G Damodar, D Venkateshwarrlu, M Narendra, M Sarat Babu, G M Sundaravalli, Orient BlackSwan

Private Limited, Hyderabad, 2009. Advanced Grammar in Use, Martin Hewings, Cambridge

University Press, New Delhi, 2008.

English Grammar & Composition, Wren & Martin, S. Chand & Company Limited, New Delhi, 2010.

English Grammar & Composition & Usage, J C Nesfield, Macmillan India Limited, 2010.



Course Objective:

The course is lay emphasis on concept of Indian political system which

specifically focused on framing and features of Indian Constitution,

fundamental rights and fundamental duties etc. Besides parliamentary

system and Panchayati Raj are also the other important topics of this course.

Indian Polity

Unit 1: Indian Constitution

Unit: 2 Indian Parliamentary System

Unit: 3 Election and Judiciary Unit 4: Panchayati Raj and local bodies

Unit 5: National Symbols and Indian Culture

Recommended Books:

Introduction to the Constitution of India, Dr. Durga Das Basu, Lexis

Nexis Butterworth Wadhwa, Nagpur.

General Study Manual, Tata Mc Graw Hill Series, New Delhi.



B TECH (2nd SEMESTER)

BS-102 ENGINEERING PHYSICS-II



Course Objective:

The objective of this course is to give an understanding of the basic knowledge and impart quality education in physical sciences to the budding engineers. To strengthen the skills in basic measurements by exposing the students to well equipped labs and enhance the problem solving ability through interactive classes.

UNIT-I

Space lattice, Unit cell and translation vectors, Lattice, Crystal Structure, Miller indices, Symmetry operations, Simple crystal structure: NaCl, CsCl, ZnS and diamond, Bonding in solids, Defects in Crystals, Bragg’s law.

UNIT-II

Drawbacks of Classical Physics, Introduction to quantum meachanics, Simple concepts, Discovery of Plank’s constant, Postulates of quantum mechanics, Group velocity and phase velocity, Schrödinger wave equation; Time dependent and time independent Schrödinger wave equation, Physical significance of wave function, Elementary ideas of quantum statistics.

UNIT-III

Free electron theory of metals, Elements of classical free electron theory and its limitations, Quantum theory of free electrons, Fermi level, Density of states, Fermi- Dirac distribution function, Thermionic emission, Richardson’s equation.

Origin of energy bands, Kronig Penny Model (qualitative), E-K diagram, Brillouin Zones, Concept of effective mass and holes, Classification of solids into metals, Semiconductors and insulators, Fermi energy and its variation with temperature, Hall effect and its applications.

UNIT-IV

Production of X-rays, Properties of X-rays, X-ray Spectrum, Continuous and characteristics, Origin of X-rays, Moseley’s Law, Absorption of X-rays.

Superconductivity, Discovery, Meissner effect, Experimental effects, Type I and Type II Superconductors, London’s equations, Applications.

Recommended Books:

Pillai S O, Solid State Physics, New Age International Publishers Puri S,Modern Physics concepts and applications, Narosa Publishers Fishlock David, A Guide to Superconductivity Kittel C, Solid State Physics

L T P Cr

3 1 - 4




BS-104 ENGINEERING MATHEMATICS-II



Course Objective:

The aim of the course is to solve the applications based on real industrial problems. Uncertainty is an essential feature of the engineering environment and for this reason the fields of probability and statistics are also included.

UNIT-I

Laplace transforms of elementary functions, Properties of Laplace transforms, Existence conditions, Transforms of derivatives, Transforms of integrals, Multiplication by tn , Division by t, Evaluation of integrals by Laplace transforms, Laplace transforms of unit step function, Unit impulse function and period function, Inverse transforms, Convolution theorem, Application to linear differential equations, Simultaneous linear differential equations with constant co-efficient.

UNIT-II

Euler’s formulae, Conditions for a Fourier expansion, Change of interval, Fourier expansion of odd and even functions, Half range sine and cosine series, Fourier expansion of square wave, Rectangular wave, Saw-toothed wave, Half and full rectified wave.

Fourier integrals, Fourier transforms, Shifting theorem (both on time and frequency), Fourier transforms of derivatives, Fourier transforms of integrals, Convolution theorem, Fourier transform of Dirac-delta function.

UNIT-III Linear Programming problems formulation, Solving linear Programming problems using (a) Graphical Method (b) Simplex Method (c) Dual Simplex Method.

UNIT-IV

Conditional probability, Bayes theorem and its applications, Expected value of a random variable, Properties and applications of Binomial, Poisson and Normal distributions.

Testing of a hypothesis, Test of significance for large samples, Student’s t- distribution (applications only), Chi-square test of goodness of fit.

Recommended Books:

Grewal B S, Higher Engineering Mathematics, Khanna Publishers Kreyszing Erwin, Advanced Engineering Mathematics, Wiley Publications Dass H K, Advanced Engineering Mathematics, Wiley Publications Sastry S S, Engineering Mathematics, Vol. II, Prentice Hall of India Taha H A, Operation Research Johnson, Probability and statistics for Engineers, PHI

L T P Cr

3 1 - 4




ES-102 INTRODUCTION TO ENVIRONMENTAL SCIENCES



Course Objective:

This course will help students to develop an understanding of various environmental issues, Need for sustainable development, Solid waste disposal, Degradation of environment, Global warming, The depletion of ozone layer, Loss of biodiversity and various environmental laws.

UNIT-I

Introduction to environmental studies, Scope and Importance, Need for public awareness.

Natural resources and associated problems, Forest resources, Use and over- exploitation, Deforestation, Case studies, Timber extraction, Mining, Dams and their effects on forest and tribal people, Water resources, Use and over-utilization of surface and ground water, Floods, Drought, Conflicts over water, Dams-benefits and problems, Mineral resources, Use and exploitation, Environmental effects of extracting and using mineral resources, Case studies, Food resources, World food problems, Changes caused by agriculture and overgrazing, Effects of modern agriculture, Fertilizer-pesticide problems, Water logging, Salinity, Case studies, Energy resources, Growing energy needs, Renewable and non renewable energy sources, Use of alternate energy sources. Case studies, Land as a resource, Land degradation, Man induced landslides, Soil erosion and desertification, Role of an individual in conservation of natural resources, Equitable use of resources for sustainable lifestyles.

UNIT-II

Concept of ecosystems, Structure and function of an ecosystem, Producers, Consumers and decomposers, Energy flow in the ecosystem, Ecological succession, Food chains, Food webs and ecological pyramids, Introduction, Types, Characteristic features, Structure and function of the following ecosystem: Forest, Grassland, Desert and Aquatic (ponds, Streams, Lakes, Rivers, Oceans, Estuaries) ecosystems.

Population growth, Variation among nations, Population explosion, Family Welfare Programme, Environment and human health, Human Rights, Value Education, HIV/AIDS, Women and Child Welfare, Role of Information Technology in Environment and human health, Case Studies.

UNIT-III

Introduction to biodiversity, Genetic, Species and Ecosystem diversity, Bio- geographical classification of India, Value of biodiversity, Consumptive use, Productive use, Social, Ethical, Aesthetic and option values, Biodiversity at global, National and local levels, India as a mega-diversity nation, Hot-sports of biodiversity, Threats to biodiversity, Habitat loss, Poaching of wildlife, Man-wildlife conflicts, Endangered and endemic species of India, Conservation of biodiversity, In-situ and Ex-situ conservation of biodiversity.Unsustainable to Sustainable development, Urban problems related to energy Water conservation, Rain water harvesting, Watershed management, Resettlement and rehabilitation of people; its problems and concerns, Case Studies. Environmental ethics: Issues and possible solutions. Climate change, Global warming, Acid rain, Ozone layer depletion.

UNIT-IV

Solid waste management, characterstics & disposal of solid waste, Recovery of resorurces, Hazrdous waste management.

Disaster management, floods, Earthquake, cyclone & Land slides, Role of an individual in prevention of pollution, pollution case studies.

Recommended Books:

Joseph Benny, Environmental Studies, The Tata McGraw-Hill Publishing Company Limited, New Delhi

Deswal S and Deswal A, A basic course of environmental studies, Dhanapath Rai & Co. Bharucha Erach, Text Book of environmental studies, UGC

L T P Cr

3 1 - 4



Joseph Kurian and Nagendram R, Essentials of environmental studies, Pearson Education Pte. Ltd., Delhi

Rajagopalan R, Environmental studies, Oxford university press. Rao C S, Environmental Pollution Control Engineering, Wiley Eastern Ltd., New Age

International Ltd. Anjaneyulu Y, Introduction to Environmental Science, B S Publications. Manoharachary C and Jayarama Reddy P, Principles of Environmental Studies, B S

Publications




ES-104 INTRODUCTION TO CADD



Course Objective:

The objective of this course is to introduce the students about how computer help in industrial designing, Basics of computer graphics, knowledge about AutoCAD software.

UNIT-I

Introduction: CAD, Benefits & Applications of CAD in industry, Design process, Computer Technology: Central processing unit (CPU), Types of Memory, The Design workstation, The graphic terminal, input devices, Plotters and other output devices, Secondary storage.

UNIT-II

Geometric modeling: Introduction, Differences between wire frame, surface and solid modeling, Curves: line, circle, ellipse, hyperbola, parabola, Bezier curve, Hermit cubic spline, B-spline, Difference between analytical curves and synthetic curves.

UNIT-III

Introduction to a drafting system; Basic facilities in Auto CAD, Basic geometric commands and Draw commands, Modify Commands, layers, Display control commands. Retrieve and use help commands.

UNIT-IV

3-D Commands in CAD software: Basic primitives like box, cylinder, cone, sphere etc., Boolean operations like intersect, Subtract, Union. Sketch based commands like Extrude, Revolve, sweep, Helical sweep. 3-D editing commands, shell, imprint, offset, etc., Printing, plotting and layout.

Recommended Books:

Narayan Lalit, Computer Aided Design and Manufacturing, PHI publications Rao PN, Principles and applications, Tata Mcgraw Hill Groover and Zimmers, Computer Aided Designand Manufacturing, Pearson Publication Omura George, Mastering AutoCAD 2012

Zeid, Theory and practice, Mcgraw Hill

L T P Cr

3 1 - 4




ES-105/106 BASICS OF ELECTRONICS ENGINEERING



Course Objective:

This course enables the students to understand the concept and behavior of passive electrical components in DC and AC circuits, Structure, Functionality and characteristics of electronic devices and their usage in designing analog and digital circuits. It also describes some advanced applications and how electronic circuits can interact with outside world.

UNIT-I

Passive Components, Signals and Networks, Resistances, Capacitors and Inductors of various types, Component Specifications, Integral relationship for inductors and capacitors, Applications, Response to dc and sinusoidal voltage/current excitations, Frequency response, Resonance, Power and energy. Transients in R-L, R-C, R-L-C, Sinusoidal Steady State, Real/Reactive Power.

UNIT-II

Basic Devices and Analog Circuits, Functional Characteristics, Structure and parameters of Diode, LED, BJT, FETs, CMOS, OP-AMP. Analog circuit Examples: Rectifiers, Amplifiers, Oscillators, Filters etc. Frequency response, Power amplifiers, Power supplies, Elements of IC regulated power supply. Use of Op-Amp as amplifier, Adder, Differentiator, Integrator and Active filters.

UNIT-III

Digital Logic, Binary numbers, Binary arithmetic, Digital logic circuits, Boolean algebra, Standard forms of Boolean functions, Simplifications of Boolean functions. Combinational logic, Flip Flops, Time parameters of flip-flops.

UNIT-IV

Basic Digital Devices, MSI and LSI design, Counters, Shift Register, Memories, CPLDs, FPGAs, DAC/ADC. Introduction to digital ICs (TTL type), CMOS inverter, Interfacing TTL and CMOS,

Recommended Books:

Bobrow L S, Fundamentals of Electrical Engineering, Oxford U. Press

Sedra, Smith K C, Micro Electronics Circuits Theory and Applications-Oxford U. Press

Toro Vincent Del, `Electrical Engineering Fundamental, Prentice Hall, 1989

Krishnamurthy K A and Raghuveer M R, Electrical and Electronics Engineering for Scientists, Wiley Eastern Ltd., 1993

Mottershed Allen, Electronic Devices and Circuits, An Introduction, EEE Publication, 12th Indian Reprint, 1989

Bapat Y N, Electronic Devices and Circuits, Tata McGraw Hill

L T P Cr

3 1 - 4




ES-108 BASICS OF MECHANICAL ENGINEERING



Course Objective:

The main objective of the course is to understand and identify the problems related to mechanical engineering, Which may come across to the students, Irrespective of any branch of engineering during their career. In present industrial scenario engineers of every field are employed, Therefore the students of every branch must know the basic concepts of mechanical engineering.

UNIT-I

Thermodynamic system, Boundary and surroundings, Open, Closed and Isolated systems, State, Property, Process and Cycle, Reversible, Quasi-static and irreversible processes, Energy and its forms, Heat and work, Zeroth law of thermodynamics, Essence and corollaries of the first law, Internal energy, Enthalpy and Specific heats, Applications of steady flow energy equation to various engineering devices, Applications of first law of TD, Limitations of first law.

UNIT-II

Various statements of second law and their equivalence, Applications of statements of second law to heat engine, Heat pump and refrigerator, Carnot theorem for heat engines and heat pump, Claussius inequality, Concept and philosophy of entropy, Third law of thermodynamics, Formation of steam at constant pressure, Thermodynamics properties of steam, Classification of boilers, Comparison of water and fire tube boilers, Boiler mounting and accessories with their functions, Introduction to IC engines, Constructional details and working of two-stroke and four-stroke diesel and petrol engines, Otto, Diesel and Dual cycles.

UNIT-III

Introduction to applied mechanics, Resultant of two forces which are not parallel, Resolution of a single force into components, Graphical method of determining the resultant of a system of coplanar forces, Lami’s theorem, Friction and its applications, Laws of coulomb friction, Coefficient of friction, Dry friction, Sliding friction, Ladder friction, Rolling Resistance, Definition of machine and lifting machine, Velocity ratio, Mechanical advantage, Efficiency, Laws of machines, Reversibility of machine, Wheel and axle, Differential pulley block, Single, Double and triple start worm and worm wheel, Single and double purchase winch crabs, Simple and compound screw jacks, Centre of gravity, Moment of an area, Centroid of a uniform lamina, Centroid of laminae of various shapes (triangle, Circle, Semi-circle, Trapezium, Built up section), Moment of inertia of laminae of different shapes (rectangular, Circular, Triangular and composite sections).

UNIT-IV

Concept and types of stresses and strains, Poison’s ratio, Stresses and strains in simple and compound bars under axial loading, Stress-strain diagrams, Hooks law, Elastic constants and their relationships, Principle stresses and strains, Mohr’s circle of stresses. Bending moment and shear force definitions, SF and BM diagrams for cantilever and simply supported beam. Calculation of maximum SF, BM and point of contra-flexure under concentrated load and uniformly distributed load.

Recommended Books:

Kumar D S, Elements of Mechanical Engineering, S K Kataria and Sons Rajput R K, Elements of Mechanical Engineering, Lakshmi Publications Ramamurtham S, Applied Mechanics, Dhanpat Rai & Sons Khurmi R S, Engineering Mechanics, S Chand Nag P K, Engineering Thermodynamics, TMH

Rattan S S, Strength of Materaials, TMH

Singh Sadhu, Strength of Materaials, Khanna Publications

L T P Cr

3 1 - 4




BS-108 PHYSICS LAB-II



EXPERIMENTS

To calibrate an electromagnet using Guoy’s balance.

To measure Hall’s co-efficient of Germanium and calculation of charge carrier concentration.

To measure i) Saturation magnetization ii) coercivity and iii) retentivity in a given ferromagnetic material.

To study the Zener Diode voltage regulating characteristics.

To determine e/m of an electron.

To study I/V characteristics and rectification properties of a semiconductor diode.

To study characteristics of a thermistor.

To determine the resistivity of a semiconductor by four probe method.

To determine the band gap of germanium from the variation of its resistivity with temperature.

To study the intensity response of a cadmium sulphide cell.

To draw the I-V characteristics of a solar cell under constant illumination.

To find the value of Planck’s constant by photo electric cell.

To study the dielectric properties of a dielectric at different frequencies by resonance method.

L T P Cr

- - 2 1




ES-109/110 ELECTRONICS ENGINEERING LAB



EXPERIMENTS

Familiarization with Electronic Components and Equipment (CRO, Function Generator, DMM)-Part-I.

Familiarization with Electronic Components and Equipment (CRO, Function Generator, DMM)-Part-II.

Verification of Superposition and Millman’s theorems.

Verification of Thevenin’s and Norton’s theorems.

Transient response of series RL, RC, RLC circuits.

Measurement & Study of p-n junction diode I-V & C-V characteristics.

Measurement & Study of input and output characteristics of a bipolar junction transistor

Study of operational amplifier-Gain Vs Bandwidth response.

Op-Amp. Applications-adder, Differentiator/integrator.

Verification of Truth table of Gates and Flip-flops.

Study of Counters.

Study of registers.

Study of DAC and ADC.

Recommended Books:

Malvino, Electronic principles, Tata McGraw Hill, 7th Edition

Malvino, Leach Digital principals and Applications, Tata McGraw Hill, 6th Edition

L T P Cr

- - 2 1




ES-112 WORKSHOP PRACTICE-II



Course Objective:

The main objective of the course is to make the engineering students familiar with the basic problems related to manufacturing which may come across during their career and their day to day life too.

EXPERIMENTS

To prepare a perfect male-female joint in a fitting shop.

To prepare half-lap corner joint, Mortise & tennon joints in carpentry shop.

To perform simple exercises on wood working lathe.

To study different types of gas welding along with construction, Working and equipments used.

To perform Oxy-Acetylene gas welding on mild steel and prepare a lap joint by Gas welding.

To study different soldering and brazing techniques used for metal joining.

To study different types of tools and its operation used in sheet metal shop with making of funnel complete with ‘soldering’.

To prepare mold and core assembly, To put metal in the mold and fettle the casting.

To prepare horizontal surface/ vertical surface/ curved surface/ slots or V- grooves on a shaper/ planner.

To prepare a job involving side and face milling on a milling machine.

Recommended Books:

Saha, Workshop Practice, TMH

L T P Cr

- - 2 1




ES-114 CAD LAB



Course Objective:

To introduce the student to basic drafting skills with CAD software, Necessary for an engineer.

EXPERIMENTS

Note: The students will be required to carry out the following exercises using software packages (e.g. Auto-CAD/ Solid Edge etc.)

Setting up of drawing environment by setting drawing limits, drawing units, naming the drawing, naming layers, setting line types for different layers using various type of lines in engineering drawing, saving the file with .dwg extension.

Learn and draw the basic entities in 2D.

Layout drawing of workshop using different layer and line colors indicating all workshop details. Name the details using text commands, Make a title Block.

Learn and use the various modify commands of the drafting software.

Use hatching and dimensioning to detail out a component drawing.

Draw 3D models by using basic primitives and operate Boolean operations on them.

Draw 3D models by extruding simple 2D objects, dimension and name the objects.

Use and learn import/export techniques and customization of drafting software.

Recommended Books:

CADD CENTRE, AutoCAD Vol 1 2 & 3 with Mechanical workbook

Omura George, Mastering AUTO CAD 2012

L T P Cr

- - 2 1




HS-102 LANGUAGE LAB



Course Objective:

To equip the learners with effective and error-free communication skills in English, With special emphasis on spoken and listening skills.

EXPERIMENTS

Communicative Grammar

Articles, Tenses, Prepositions, Adjectives, Adverbs, Voices, Subject-verb agreement

Spoken Skills

Transcription of words into IPA

Stress

Intonation

Weak Forms (transcription of weak forms into IPA)

Software- based Speaking Exercises

Listening Skills

Listening & Hearing

The Process of Listening

Types of Listening

Listening Influencers

Improving Listening Skills

Listening Comprehension

Recommended Books:

Bansal R K and Harrison J B, Spoken English: A Manual of Speech and Phonetic Orient Longman.

Hornby A S, Oxford Advanced Learners Dictionary of Current English Oxford University. Murphy Raymond, Intermediate English Grammar Cambridge University Press Barun K, Effective Technical Communication, Oxford Higher Education. Tyagi, Kavita and Padma Misra, Basic Technical Communication PHI Learning

L T P Cr

- - 2 1




EGA-102* ENGLISH AND GENERAL AWARENESS-II

L T P Cr External Evaluation: 25 Marks 1 - - 1

Assumption:

The course is specifically designed for students from the rural background who have studied in Hindi medium schools. The purpose is to fill in the gaps in their knowledge which they may have due to lack of exposure and to enrich their vocabulary and command over grammar.

Course Objective:

The course aims at helping the students enhance their quality of English communication by developing an understanding of correct usage of words and phrases. It also helps them frame grammatically as well as logically correct sentences.

A Communicative Approach To Learning English

Unit 1: Using English in Different Context Unit 2: Set Expression and Idiomatic Response Unit 3: Phrasal Verbs in Different Context Unit 4: Use of Prefixes and Suffixes Unit 5: Emphasis through Phrasing

Recommended Books: Learning English, A Communicative Approach, Rama Krishna Rao, Orient Longman Private

Limited, Hyderabad, 2008. Improve Your Written English, Marion Field, Jaico Publishing House, New Delhi, 2006. English for Empowerment, G Damodar, D Venkateshwarrlu, M Narendra, M Sarat Babu, G M

Sundaravalli, Orient BlackSwan Private Limited, Hyderabad, 2009. Advanced Grammar in Use, Martin Hewings, Cambridge University Press, New Delhi, 2008. English Phrasal Verbs in Use, Michael McCarthy, Felicity O’Dell, Cambridge University Press,

2008. Oxford Word Skills, Ruth Gairns and Stuart Redman, Oxford University Press, 2009. English Vocabulary in Use, Michael McCarthy, Felicity O’Dell, Cambridge University Press,

2008.

Course Objective:

The object of this course is to provide the information on the history of India from pre-

Maurya period to freedom struggle and India’s independence.

Indian History

Unit 1: Pre- Maurya and Maurya Period

Unit 2: Gupta Empire to Mughal Empire

Unit 3: Europeans and Cultural Movement

Unit 4: Pre-Gandhian Era to the rise of Revolutionaries

Unit 5: Quit India Movement and India’s Independence



Recommended Books:

Total History and Civics, Dolly Ellen Sequeria, Ms. Nidhi M Pinto for Morning Star,

Daryagang, New Delhi.

Social Science, National Council of Educational Research and Training, New Delhi.

Themes in Indian History Part II, National Council of Educational Research and

Training, New Delhi.



Page 40 B Tech: 3rd to 8th Semester - Civil Engineering

B TECH (3rd SEMESTER) CIVIL ENGINEERING

CE-201 STRUCTURAL ANALYSIS-I

Internal Evaluation: 50 Marks

External Examination: 50 Marks Duration of Examination: 03 Hours

Course Objective:

To make the students understand the basic concepts of stress and strains theory as well as about the bending moment and shear force diagram.

UNIT-I

Elasticity, Plasticity, Ductility, Brittleness, Strength, Types of stresses and strains, Stress strain diagram, Hookes law, Principle of superposition, Bars of varying section of different materials, Compound bars, Temperature stresses etc. Modulus of elasticity, Poison’s Ratio, Modulus of Rigidity and bulk modulus, And their relationships.

UNIT-II

Strains Energy, Resilience and Impact loading- Load deflection diagram: Strain energy of prismatic bars with varying section, For non prismatic bars with stresses under gradual, Sudden and impact loadings, Shear resilience, Relation between Elastic moduli and strain energy.

Stresses induced due to uni-axial stress, Stresses induced by state of simple shear stresses induced due to biaxial stress, Mohr Circle, Ellipse of stress, Principal stresses and principal planes, Maximum shear stresses, Principal strains. Theory of Failures.

UNIT-III

Theory of simple bending, Distribution of bending stresses, Distribution of shear stresses. Concept of structural stability, Slenderness ratio, End connections, Analysis of long and short columns by Euler’s, Rankine’s and Secant formulae, Analysis of eccentrically and laterally loaded columns, Cylinder columns subjected to axial and eccentric loading.

UNIT-IV

Shear Force and Bending Moment, Types of structures, Loading, Supporting conditions, Structural actions, Equation of equilibrium, Shear force and bending moment diagram under different loads for determinate beams, Frames and arches. Three hinged arch-horizontal thrust, Shear force and bending moment diagrams.

Analysis of statically determinate trusses-Introduction, Various types, Stability, Analysis of plane trusses by method of joints and method of sections, Analysis of space trusses using tension coefficient method.

Recommended Books:

Punmia B C and Jain A K, Mechanics of Materials, Laxmi Publication, 2005 Jain A K, Elementary Structural Analysis, Nem Chand & Bros, Roorkee Timoshenko S and Young D H, Elements of strength of materials, Van Nostrand, 1968 Utku S, Norris C H & Wilbur J B, Elementary structural analysis, McGraw-Hill, 1991 http://nptel.iitm.ac.in/video.php?subjectId=105105108

L T P Cr

3 1 - 4

http://nptel.iitm.ac.in/video.php?subjectId=105105108




CE-203 FLUID MECHANICS-I



Course Objective:

This course gives an introduction to the fundamentals of fluid flow and its behavior so as to equip the students to learn related subjects and their applications in civil engineering.

UNIT-I

Introduction- Basic equations, Pressure and its relationship with height, Pressure diagram, Hydrostatic forces on submerged bodies, Buoyancy and floatation, Liquids in relative equilibrium.

Fluid kinematics, Flow characteristics, Continuity equation, Acceleration of fluid particles, Rotational and irrotational motion, Circulation and vorticity, Velocity potential and stream function, Streamlines, Equipotential lines, Flow net method, Use and limitations.

UNIT-II

Fluid dynamics- Euler’s equation, Energy equation and Bernoulli’s equation, Application of Bernoulli’s equation, Orifice meter, Venture meter, Pivot tube etc., Flow through orifice, Mouth piece, Weir and notches, Impulse momentum equation and its application, Pipe junction, Bends, Stationary flat and curved vanes, Moment of momentum equation. Flow through pipes: Reynolds’ experiment, Laws of fluid friction, Darcy Weisbach equation, Energy losses, Equivalent pipe, Pipes in series and parallel, Branched pipes, Time of emptying a reservoir through pipe, Pipe networks.

UNIT-III

Laminar flow- Laminar flow through circular pipes, Parallel plates, Open channel, Porous media, Couette flow, Stokes law, Measurement of viscosity, Transition from laminar to turbulent flow.

Dimensional analysis and similitude- Dimensional homogeneity, Non Dimensional parameter, Buckinghum pie theorem, Dimensional analysis chice of variables, Reyleigh methods, Examples Rise in capillary tube, Head characteristics of a pump, Drag on a ship, Fall velocity of a sphere, Velocity in an open channel, Pipe orifice, Discharge over a sharpedge weir, Celerity of a gravity wave. Model analysis similitude, Types of similarities, Force ratios, Similarity laws, Model classification, Scale effects.

UNIT-IV

Boundary layer theory, Types, Boundary layer thickness and equations, Momentum integral equation boundary layer on rough surfaces, Total drag on flat plate due to laminar and turbulent boundary layer, Boundary layer separation and its control. Turbulent flow- Shear stresses, Establishment of flow, Types of boundaries, Mixing length concept, Velocity distribution, Mean velocity and resistance to flow in smooth and rough pipes, Friction in non circular conduits.

Flow measurement, Measurement of pressure static, Dynamic and total pressure, Piezometric head, Measurement of velocity Pitot tube and prandtll tube. Measure flow through orifice, Mouth piece, Weir and notches, Measurement of dischargeorifice, Mouthpiece weir and notches, Orifice meter, Flow nozzle, Venturi flume.

Recommended Books:

Modi P N and Seth S M, Hydraulics and Fluid Mechanics, Standard Book House, 2011 Pandhare A P, Jadhav S S, Fluid Mechanics, Technical Publication, Pune, 2009 Garde R J and Mirajgaoker A G, Fluid Mechanics, Roorkee Publishing House, 1972 http://nptel.iitm.ac.in/courses/Webcourse,contents/IIT,%20Guwahati/fluid_mechanics/ind

ex.htm


L T P Cr

3 1 - 4

http://nptel.iitm.ac.in/courses/Webcourse%2Ccontents/IIT%2C%20Guwahati/fluid_mechanics/ind





CE-205 SURVEYING-I



Course Objective:

To acquaint students about basic principles and basic instruments related with surveying & levelling. They will learn the way to measure distance, Direction and angles.

UNIT-I

Introduction, Classification of surveys, Reconnaissance, Principle of working from whole to part, Provision of control, Conventional signs,chain survey, Instruments for measuring distance, Principles of chain survey, Field book, Plotting, Tie line and check line, Chaining and ranging – obstacles in both chaining, Ranging, Chaining on sloping ground, Errors in chain survey, Tape corrections examples.

Compass survey: prismatic compass, Surveyor’s compass, Whole circle and reduced bearing, True and magnetic bearing, Dip and declination, Local attraction, Plotting of a traverse: various methods, Independent coordinates, Error of closure, Graphical and analytical adjustments of traverse.

UNIT-II

Levelling – Various definitions including level surfaces, Mean sea level, Reduced level, And bench marks – levels: Dumpy, Tilting, Auto, Digital, Temporary and permanent adjustments of level, Booking and reduction of levels, Corrections for refraction and curvature, Fly leveling, Reciprocal leveling, Profile leveling and cross sectioning, Sensitivity of bubble tube, Contour survey, Definition, Characteristics of contour,uses of contour, Methods of contouring, Direct and indirect interpolation, Plotting, Areas and volumes, Trapezoidal rule, Simpson’s rule, Area from latitude and departure, Uses of planimeter, Volumes, Trapezoidal and prismoidal formula.

UNIT-III

Theodolite, Temporary and permanent adjustment of theodolite, Measurement of angles, Repetition and reiteration method, Traversing with theodolite, Checks in traversing, Adjustment of closed traverse, Omitted measurements, Examples.

Tacheometry- uses of tacheometry, Principle of tacheometric surveying, Systems of tacheometric surveying, Stadia system fixed hair method, Determination of tacheometric constants, Tangential systems, Examples.

UNIT-IV

Plane table survey- instruments and accessories, Different methods, Orientation, Advantages and disadvantages of plane tabling, Two point problem, Three point problem, Errors in plane tabling.

Curves – Types of curves – elements of curve – simple curves – different methods of setting out simple curve, Transition curves and vertical curves and examples.

Global positioning system, Principle, Working, Components, Errors.

Recommended Books:

Punmia B C, Surveying Vol. I, Laxmi Publishers, 2005 Arora K R, Surveying Vol. I, Standard Book House Bhatta B, Remote sensing and GIS, 2009, Oxford University press Ghilani C D, Wolf P R, Elementary Surveying, Pearson Education, Limited, 2011. http://nptel.iitm.ac.in/courses/Webcourse,contents/IIT,ROORKEE/SURVEYING/home.htm

http://nptel.iitm.ac.in/courses/Webcourse,contents/IIT,KANPUR/ModernSurveyingTech/ui/ TOC1.htm

L T P Cr

3 1 - 4

http://nptel.iitm.ac.in/courses/Webcourse%2Ccontents/IIT%2CROORKEE/SURVEYING/home.htm

http://nptel.iitm.ac.in/courses/Webcourse%2Ccontents/IIT%2CKANPUR/ModernSurveyingTech/ui/




CE-207 BUILDING CONSTRUCTION AND MATERIALS



Course Objective:

To acquaint students about various material and methods used in construction as well the characteristics of different materials used for building construction.

UNIT-I

Classification of stones, Requirements of good materials, Querying of stones, Common building stones. Classification of bricks, Constituent of a good brick earth, Harmful ingredients, Manufacturing of bricks, Testing of bricks.

Manufacturing of tiles and terra cotta, Types of terra cotta, Uses of terra cotta, Classification, Manufactures of lime, Artificial hydraulic lime, Pozzolana, Field testing of lime.

Composition, Manufactures of Portland cement, Field testing of cement, Special types of cements, Storage of cement. Types of steel, Marketable forms, Stress strain behaviour.

UNIT-II

Various constituents of cement concrete, Preparation and properties of concrete in fresh state, Factors affecting workability, Durability and strength, Characteristic strength, Stress strain behaviour, Acceptance criteria, Mix design and physical tests.

Classification of timber, Structure of timber, Seasoning of timber, Defects in timber, Important Indian timbers.

Constituents of paints, Types of paints, Types, Constituents and characteristics of varnishes, Miscellaneous. Polymetric materials, PVC, Polyester, HDPE, CDPE etc. Classification, Properties and applications in civil engineering.

UNIT-III

Various terms used in brick and stone masonry, Types, Tools used, Bonds in brick work, Dressing of stones, Applications for lifting stones.

Types of non bearing partition brick partitions, Clay block partitions, Timber partitions and glass partitions, Construction of a masonry cavity walls.

Lintels-classification and loading, Arches-classification and construction details, Technical terms.

Sources of dampness, Effects of dampness, Prevention of dampness, Materials used in damp proofing course.

UNIT-IV

Types of roofs, Terms used in sloping roof, King post truss, Queen post truss, Simple steel roof trusses, Types and uses of roofing materials

Components of floor, Brick floors, Cement concrete floors, Terrazzo flooring, Mosaic floorings, Tiled flooring.

Locations of doors and windows, Sizes general types of door movement, Various types of doors and windows.

Finishing works, Plastering, Pointing, Painting, White washing, Colour washing, Distempering, Damp proofing ant termite treatment.

Recommended Books:

Singh S, Engineering Materials, Stosius Inc/Advent Books Division, 1990 Punmia B C, Building Construction, Laxmi Publication, 2005. Rangwala S C, Engineering Materials, Charotar Publishing House Pvt. Ltd., 2008 Relevant I.S. Codes http://nptel.iitm.ac.in/video.php?subjectId=105102088

L T P Cr

3 1 - 4





CE-209 DESIGN OF STEEL STRUCTURES-I



Course Objective:

To acquaint students about behaviour of different type of steel section used in construction industry and the design of simple steel structures.

UNIT-I

Properties of structural steel. I.S.Rolled sections and I.S. specification. Importance of connections, Various types of connections, Simple and moment resistant, Riveted, Bolted and welded connections. Design of bolted, Riveted and welded joints.

Types of Tension members –Behaviour of Tension members – Net Sectional Area, Design of Tension Members.

Types of compression members – Theory of columns, Basis of current codal provision for compression member design – Slenderness ratio, Design of Compression Members – Design Criteria, Laced and Battened columns, Column Bases

UNIT-II

Design of Beams subjected to biaxial bending moment, Design of sections subjected to unsymmetrical bending, Elastic lateral torsional buckling, Beam Columns, Short and Long Beam, Columns – Beam Columns at Ultimate Load, Effects of Slenderness Ratio and Axial force on Modes of Failure, Beam, Column under Biaxial bending.

UNIT-III

Column Bases and Footings, Introduction, Types of column bases, Design of slab base and gussested base, Design of gusseted base subjected to eccentrically loading, Design of grillage foundations.

Design of Industrial building Frames – Design of Purlins for Roof Trusses, Analysis of simple bents, Sway and non-sway frames, Design of Gable frames, Design of knee bracing, Vertical bracing.

UNIT-IV

Introduction to plate and girder, Elements of plate girder, Design steps of a plate girder, Necessity of stiffeners in plate girder, Various types of stiffeners, Web and flange splices (brief introduction), Curtailment of flange plates, Design beam to column connections: Introduction, Design of framed and seat connection.

Recommended Books:

Ramchandra and Gehlot V, Design Of Steel Structures (Vol.-I), Scientific Publishers, 2009 Punmia B C, Jain A K And Jain A K, Comprehensive Design of Steel Structures, Laxmi

Publications, New Delhi, 2nd Edition, 1998 Arya A S & Ajmani J L, Design of Steel Structures, Nem Chand & Brothers, 1974 Ragupathy M, Design of Steel Structures, Tata McGraw, Hill Publishing Co. Ltd., New Delhi,

1996

L T P Cr

3 1 - 4




HS-201 ESSENTIALS OF MANAGEMENT AND ORGANIZATIONAL BEHAVIOUR



Course Objective:

To help the students lay a foundation to an understanding of Management and Organizational behavior which are essential fields of study to make a success of both their professional and personal lives.

UNIT-I

Concept of management, Characteristics and Importance, Management vs Administration, Management as an art a science and as a profession, Levels of Management, Contributions of Henry Fayol, FWTaylor & Elton Mayo, Management Functions: Planning, Organizing, Staffing, Directing and Controlling.

UNIT-II

Concept & significance of Organizational Behavior, Challenges and opportunities in the field of OB, Model of OB.

Learning, Attitude, Job Satisfaction, Personality, Perception and Individual Decision- making, Motivation, Theories of Motivation by Maslow, Herzberg and McGregor.

UNIT-III

Classification of Groups, Stages of Group Development, Group Properties, Group Decision-making.

Types of Teams, Creation of an Effective Team, Difference between a group and a team.

Styles of Leadership, Theories of Leadership by Blake and Mouton, Contingency Theory by Fiedler.

UNIT-IV

Organizational Structure, Common Organizational Design, New Organization Design options, Change, Organizational Change, Planned Change, Resistance to Change, Models of Organizational Change.

Recommended Books:

Koontz , Essentials of Management, Tata McGraw Hill

Robbins and Coulter, Management, PHI, 8th Ed.

Robbins and Judge, Organizational Behavior, Pearson

Pareek, Understanding Organizational Behavior, Oxford

Luthans, Organizational Behaviour, McGraw Hill Education

L T P Cr

3 1 - 4




CE-211 STRUCTURAL MECHANICS LAB-I



EXPERIMENTS

Verification of reciprocal theorem of deflection using a simply supported beam.

Verification of moment area theorem for slopes and deflections of the beam.

Deflections of a truss- horizontal deflections & vertical deflections of various joints of a pin- jointed truss.

Elastic displacements (vertical & horizontal) of curved members.

Experimental and analytical study of 3 hinged arch and influence line for horizontal thrust.

Experimental and analytical study of behaviour of struts with various end conditions.

To determine elastic properties of a beam.

Uniaxial tension test for steel (plain & deformed bars)

Uniaxial compression test on concrete & bricks specimens.

L T P Cr

- - 2 1




CE-213 FLUID MECHANICS LAB-I



EXPERIMENTS

To determine metacentric height of the ship model.

To verify the Bernoulli's theorem.

To determine coefficient of discharge for an Orificemeter.

To determine coefficient of discharge of a venturimeter.

To determine the various hydraulic coefficients of an Orifice (Cd,Cc,Cv).

To determine coefficient of discharge for an Orifice under variable head.

To calibrate a given notch.

To determine coefficient of discharge for a mouth piece.

Drawing of a flownet by Viscous Analogy Model and Sand Box Model.

To study development of boundary layer over a flat plate.

To study velocity distribution in a rectangular open channel.

L T P Cr

- - 3 1.5




CE-215 SURVEYING LAB-I



EXPERIMENTS

Chain traversing.

Compass traversing.

Leveling

Differential leveling

Fly levelling

Plotting of longitudinal section and cross sections.

Use of Automatic and digital level.

Reciprocal leveling.

Study of various instruments used in Plane table surveying

Radiation method of plane Tabling

Intersection method of plane tabling

Two point problem in plane table surveying

Three point problems in plane table surveying

Contouring and preparation contour map.

L T P Cr

- - 3 1.5




ELGA-201 ENGLISH LANGUAGE AND GENERAL AWARENESS-III


Assumption:

The course is specifically designed for students from the rural background who have studied

in Hindi medium schools. The purpose is to fill in the gaps in their knowledge which they

may have due to lack of exposure and to enrich their vocabulary and command over

grammar.

Course Objective:

The course is designed to help students develop effective communication skills, and hence, it

lays emphasis on their spoken and listening skills.

Spoken English and listening skills

Unit1: Transcription of words into IPA

Unit 2: Intonation, Stress and Weak form of words

Unit 3: Listening and Hearing, and types of listening

Unit 4: Listening skills

Unit 5: Listening comprehension

Recommended Books:

Better English Pronunciation, J.D.O’ Connor, Cambridge University Press, New Delhi.

English Phonetics and Phonology, Peter Roach, Cambridge University Press, New Delhi.

How to write and speak better, The Reader Digest Association Ltd, New Delhi.

Course Objective:

The objective of this course is to provide fundamental and important information on World

and Indian geography. The students will be able to understand about their environment and

geographical activity.

World and Indian Geography

Unit 1: Universe, Planets and Climatic Conditions

Unit 2: Geography of India

L T P Cr

1 - - 1



Unit 3: Global Facts and Figures

Unit 4: States of India

Unit 5: Indian Infrastructure

Recommended Books:

Social Science, Resources and Development, National Council of Educational

Research and Training, New Delhi.

India People and Economy, National Council of Educational Research and Training,

New Delhi

Contemporary India II, National Council of Educational Research and Training, New

Delhi.




B TECH (4th SEMESTER) CIVIL ENGINEERING

CE-202 STRUCTURE ANALYSIS-II



Course Objective:

To equip the students with the advance methods of structural analysis with emphasis on analysis of frames, Arches and trusses.

UNIT-I

Statically Indeterminate Structures, Introduction, Castigliano's theorems, Strain energy method, Analysis of frames with one or two redundant members using Castigliano's 2nd theorem.

Slope deflection and moment Distribution Methods, Analysis of continuous beams & portal frames, Portal frames with inclined members, Frames undergoing user support settlement, Distribution Factors; Application to Beams and Frames without side sway; Application to Frames with side sway; Beams and Frames with uneven loading; Support Settlement.

UNIT-II

Column Analogy Method- Elastic centre, Properties of analogous column, Applications to beam & frames. Strain energy method of analysis; Introduction to nature methods of analysis; Flexibility Method; Stiffness method. Influence lines and moving loads, Definition of influence line– influence line for statically determinate beams– criterion for maximum reaction or shear in simple beams – criterion for maximum bending moment in simple beams – absolute maximum bending moment in a simple beam – Muller Breslau influence theorem for statically determinate beams– influence lines for statically determinate trusses– criterion for maximum bending moment at a panel point on the loaded chord of a truss– criterion for maximum bending moment at a panel point on the unloaded chord of a truss– criterion for maximum bending moment at a panel point on the web member of a truss – Muller Breslau influence theorem for statically determinate trusses

UNIT-III

Analysis of Two hinged Arches, Parabolic and circular Arches, Bending Moment Diagram for various loadings, Temperature effects, Rib shortening, Axial thrust and Radial Shear force diagrams.

Unsymmetrical Bending Introduction, Centroidal principal axes of sections, Bending stresses in beam subjected to unsymmetrical bending, Shear centre, Shear centre for channel, Angles and Z sections.

UNIT-IV

Approximate methods of multistory frame analysis, Vertical and lateral load analysis of multistory frames– degree of indeterminacy– assumptions for vertical load analysis– assumptions for lateral load analysis– portal method– cantilever method– alternate moment and shear distribution– comparison of methods.

Cable and suspension Bridges, Introduction, Uniformly loaded cables, Temperature stresses, Three hinged stiffening Girder and two hinged stiffening Girder.

Recommended Books:

Gupta S P and Pandit G S, Theory of Structures, (Vol. I) Tata McGraw Hill, New Delhi, 1999.

Jain A K, Advanced Structural Analysis, Nem Chand & Bros., Roorkee. Jindal R L, Indeterminate Structures, S. Chand & Co., New Delhi, 1966. Wang C K, Statically Indeterminate Structures, McGraw Hill Book Co., New York Wang C K, Intermediate Structural Analysis, McGraw Hill International Edition, 1984

L T P Cr

3 1 - 4




CE 204 FLUID MECHANICS-II



Course Objective:

To acquaint students about behaviour and characteristics of water flow and machinery used in water engineering.

UNIT-I

Open Channel flow, Types of flow, Types of Channel, Velocity distribution, Chezy, Manning and Basin formulae, For uniform flow, Most economical section, Critical flow, Specific energy, Specific force. Computation of uniform flow and critical flow. Open channel flow: Non-Uniform flow, Dynamic equation for gradually varied flow, Computation for length of backwater curve, Rapidly Varied flow, Hydraulic jump, Types, Uses. Surges in open channels.

UNIT-II

Types of flows, Reynold's experiment, Shear stress on turbulent flow, Boundary layer in pipes, Establishment of flow, Velocity distribution for turbulent flow in smooth and rough pipes, Resistance to flow of fluid in smooth and rough pipes, Stanton and Moody's diagram.

Darcy’s weisbach equation, Other energy losses in pipes, Loss due to sudden expansion, Hydraulic gradient and total energy lines, Pipes in series and in parallel, Equivalent pipe, Branched pipe, Pipe networks, Hardy Cross method, Water hammer.

Types of drag- drag on a sphere, Flat plate, Cylinder and airfoil, Development of lift on immersed bodies like circular cylinder and airfoil.

UNIT-III

Basics of Turbo machinery, Impulse momentum equation, Hydrodynamic forces of jets on vanes, Velocity Triangles, Angular momentum principle, Application to radial flow turbines.

Turbines, Classification, Impulse and reaction turbines, Characteristic curves, Draft tubes, Governing of turbines, Specific speed, Unit quantities concept, Similarity, Cavitation.

UNIT-IV

Pumps- Centrifugal pumps, Classification, Work done, Minimum starting speed, Losses and efficiencies, Specific speed, Multistage pumps, Specific speed, Characteristic curves, NPSH, Cavitation in pumps. Reciprocating pumps, Types, Effects of acceleration and frictional resistance, Separation, Air vessels, Work saved by fitting air vessels.

Recommended Books:

Modi P N and Seth S M, Fluid Mechanics and Hydraulic Machines, Standard Book Home, New Delhi, 2005

Subraminayam S, Flow in Open Channels, McGraw Hills, 2009 Douglas J F, Gasiorek J M and Swaffield J A, Fluid Mechanics (4th Ed.). Pearson Education

India, 2002 Das M M, Fluid Mechanics and Turbo machines, Prentice Hall of India (P) Ltd New Delhi,

2008 Arora K R, Fluid Mechanics, Hydraulic and Hydraulic Machines, Standard Publishers and

Distributors, New Delhi, 2005

L T P Cr

3 1 - 4




CE-206 SURVEYING-II



Course Objective:

To understand advanced concepts of surveying by using basic instruments and to study modern trends in surveying.

UNIT-I

Classification of triangulation system, Operation in triangulation survey, Reconnaissance, Selection of site for base line, Its measurement and extension, Correction to base line measurement, Selection of stations, Triangulation figures, Scaffolds and signals, Marking of stations, Intervisibility, Strength of figure, Reduction to centre, Derivation of relations when observations are taken from the satellite station and towards the station.

Introduction to trigonometrical levelling, Determination of level of the top of an object when its base is accessible and not accessible, Determination of height of object when two instrument stations are not in the same vertical plane, Indirect leveling on a rough terrain, Indirect levelling on a slopes, Effect of refraction and curvature axis signal correction, Difference in elevation in single observation, Difference in elevations by reciprocal observation

UNIT-II

Theory of Errors- Definitions, Law of weight, Probable errors, Most probable value, Normal equations, Method of least square, Triangle station adjustment, Figure adjustment, Quadrilateral and polygon adjustment of closed traverse and level nets.

UNIT-III

Photogrammetry- Basic concepts, Type of photographs, Geometry of vertical aerial photographs, Measurement of parallax and height determination.

Components of GIS, Data acquisition, Spatial and attribute data, Pre-processing, Storage and management, Data structures, Raster and vector data

UNIT-IV

Remote sensing system, Data acquisition and processing, Applications, Multi concept in remote sensing. Physical basis of remote sensing, Electromagnetic radiation (EMR), Nature, Nomenclature and radiation laws; Interaction in atmosphere, Nature, Its effects in various wavelength regions, Atmospheric windows; Interaction at ground surface, Soils and rocks, Vegetation, Water, Etc.; Geometric basis of interaction. Platform and sensors, Terrestrial, Aerial and space platforms; Orbital characteristics of space platforms, Sun, And geosynchronous; Sensor systems, Radiometers, Opto- mechanical and push broom sensor; Resolution, Spectral, Spatial, Radiometric and temporal; Image interpretation, Elements of interpretation.

Recommended Books:

Punmia B C, Surveying Volume II, Laxmi Publisher, 2005. Arora K R, Surveying Vol. II, Standard Book House Bhatta B, Remote sensing and GIS, Oxford University press, 2009. http://nptel.iitm.ac.in/courses/Webcourse,contents/IIT,ROORKEE/SURVEYING/home.htm

http://nptel.iitm.ac.in/courses/Webcourse,contents/IIT,KANPUR/ModernSurveyingTech/ ui/TOC1.htm

L T P Cr

3 1 - 4

http://nptel.iitm.ac.in/courses/Webcourse%2Ccontents/IIT%2CROORKEE/SURVEYING/home.htm

http://nptel.iitm.ac.in/courses/Webcourse%2Ccontents/IIT%2CKANPUR/ModernSurveyingTech/




CE-208 DESIGN OF CONCRETE STRUCTURES-I



Course Objective:

To provide the students with the knowledge of the behaviour of reinforced concrete structural elements under various loading conditions and to enable them to design such elements under various loads.

UNIT-I

Material strength and properties, Grades of concrete and steel, Characteristic strength and working strength, Types of loads, Characteristic loads, Load combinations, Working Stress Method of design of RC sections, Principles, Assumptions, Durability and fire resistance, Moment of resistance of singly and doubly reinforced rectangular and flanged sections, Deflection criterion for flexural members, Bond, Flexural and anchorage bonds, Development length, Design of sections subjected to flexure, Shear and torsion using Working Stress Method.

UNIT-II

Limit State Method of design of RC sections, Principles and assumptions, Partial safety factors, Comparison with Working Stress Method, Advantages, Moment of resistance of singly and doubly reinforced rectangular and flanged sections, Bond, Flexural and anchorage bonds, Development length, Design of sections subjected to flexure, Shear and torsion using Limit State Method.

UNIT-III

Design and detailing of simply supported, Cantilever and continuous RC beams, Design and detailing of one way simply supported and continuous RC slabs, IS Code coefficients for continuous beams and slabs, Design and detailing of two way RC slabs with various support conditions using IS Code coefficients. All designs shall be done by both Limit State and Working Stress Methods with greater importance attached to the former.

UNIT-IV

Retaining Walls-Classification, Forces on retaining walls, Design criteria, Stability requirements, Proportioning of cantilever retaining walls, Counter-fort retaining walls, Criteria for design of counter-forts, Design examples. Design and detailing of RC columns by Working Stress Method– general principles, Axially loaded short and long columns– helically reinforced columns– short and long columns with eccentric loads– design and detailing of RC tension members by Working Stress Method.

Recommended Books:

Dayaratnam P, Design of Reinforced Concrete Structures, Oxford & IBH Pub. New Delhi Jain A K, Reinforced Concrete, Limit State Design, Nem Chand & Bros., Roorkee Sinha S N, Reinforced Concrete Design, Tata McGraw Hill Varghese P C, Limit State Design of Reinforced Concrete, Prentice Hall of India Gambhir M L, Design of Reinforced Concrete Structures, Prentice Halls of India Limited,

2008 Punmia B C, Jain A K and Jain A K, Limit State Design of Reinforced Concrete, Laxmi

Publications (P) Ltd., 1st Edition, 2007 SP-16(S&T), 1980, 'Design Aids for Reinforced Concrete to IS:456, BIS, N.Delhi SP-34(S&T),1987 'Handbook on Concrete Reinforcement and Detailing', BIS, N.Delhi

L T P Cr

3 1 - 4



B TECH (4th SEMESTER) CIVIL ENGINEERING CE-210 CONCRETE TECHNOLOGY



Course Objective:

To study details regarding properties and testing of cement, Mortar, Concrete and concrete mix design.

UNIT-I

Cement- Manufacture of Portland cement, Basic chemistry of cement, Hydration of cement, Heat of hydration and strength, Tests on cement: fineness of cement, Consistence of standard cement paste, Setting time, Soundness, Strength, Types of Portland cement: Ordinary Portland cement, Rapid hardening cement, Low heat cement, Sulphate resisting cement, Blast furnace cement, Supersluphated (slag) cement, White and colored cement, Portland pozzalona cement, Expansive high alumina cement Normal aggregate: Size classification, Petrographic classification, Shape and texture classification, Mechanical properties: bond, Strength, Toughness, Hardness, Physical properties: specific gravity, Bulk density, Porosity and absorption, Moisture content, Bulking of sand, Unsoundness due to volume changes, Thermal properties, Deleterious substances, Organic impurities, Clay and other fine materials, Salt contamination, Unsound due to impurities, Sieve analysis, Grading curves, Fineness modulus, Grading requirements, Maximum size aggregate, Practical grading, Gap graded aggregate

UNIT-II

Fresh concrete- workability, Factors affecting workability, Cohesion and segregation, Bleeding, Workability test, Slump test, Compacting factor test, Vebe test, Flow table test, Ball penetration test, Density of fresh concrete, Strength of concrete: tensile strength considerations, Behavior under compressive stress, Practical criteria of strength, Porosity, Gel/space ratio, Total voids in concrete, Pore size distribution, Micro cracking and stress-strain relation, Factors affecting strength.

UNIT-III

Mixing, Handling, Placing and compacting concrete: mixers, Charging the mixer, Uniformity of mixing, Mixing time, Prolonged mixing, Ready, Mixed concrete, Handling, Pumped concrete, Placing and compacting, Vibration of concrete, Internal vibrators, External vibrators, Vibrating tables, Re-vibration, Shortcrete, Preplaced aggregate concrete Admixtures: accelerators, Set retarders, Water reducers (plasticizers), Superplaticizers, Mineral additives, Bonding admixture, Water repellent admixtures Concerting in extreme climates: hot weather concreting, Cold weather concreting

UNIT-IV

Development of strength- normal curing, Method of curing, Influence of temperature, Maturity rule, Steam curing Strength properties of concrete: relation between tensile and compressive strength, Fatigue strength, Impact strength, Resistance to abrasion, Bond to reinforcement, Modulus of elasticity, Factors affecting the modulus of elasticity, Poisson’s ratio Testing: precision of testing, Analysis of fresh concrete, Strength test, Compressive strength, Tensile strength, Test core, Accelerated curing, Schmidt hammer, Penetration resistance, Pullout test, Ultrasonic pulse velocity test, Mix design: Bureau of Indian Standard method.

Recommended Books:

Shetty M S, Concrete Technology, S.Chand and Company Ltd, 2008 Gambhir M L, Concrete Technology, Tata McGraw Hill, 2004 Santhakumar A R, Concrete Technology, Oxford University Press, 2006 Neville A M and Brooks J J, Concrete Technology, Pearson, 1987 Mehta P K and Monteiro P J M, Concrete, Microstructure, Properties of Materials, TMH 2006 SP-34(S&T), 1987 'Handbook on Concrete Reinforcement and Detailing', BIS, N.Delhi

L T P Cr

3 1 - 4




HS-202 FUNDAMENTALS OF BUSINESS & ECONOMICS



Course Objective:

To provide the students a basic understanding of Business and Economics which are vital constituents of the overall professional environment of an Engineer.

UNIT-I

Nature and Significance of Human Resource Management, Functions of Human Resource Management, Manpower Planning, Job Analysis, Job Description & Job Specification, Recruitment, Selection, Training & Development, Compensation Management, Performance Appraisal, Employee Welfare, Safety and Health, Human Resource Development.

UNIT-II

Meaning, Scope and Goals of Financial Management, Investment Decision, Nature, Importance, Evaluation Criteria, Financing Decision, Long Term Sources of Funds, Cost of Capital, Capital structure, Leverage, Dividend Decision, Models and determinants of dividend decision, Working Capital Management, Theories and determinants, Forecasting of working capital, Management of Cash.

UNIT-III

Concepts of market, Marketing and marketing management, Marketing Environment- Analyzing needs & trends in macro environment, Economic environment, Technical environment, Political environment, And socio-cultural environment, Market Segmentation, Targeting and positioning strategies, Marketing mix, Product, Meaning, Product mix, Levels of product, Product life cycle, Price, Meaning, Importance, Pricing objectives and strategies, Place, Importance, Functions of distribution channels, Promotional mix-advertising, Sales promotion, Personal selling, Public relations, Direct marketing.

UNIT-IV

Meaning and significance of Economics, Role of economics in engineering and technology, Basic economic terms, Utility, Saving, Investment, Equilibrium, Micro and macro economics, Economic policies, Globalization, Privatization, Liberalization, Demand &Supply Analysis, Meaning of demand and supply, Law of demand and supply, Elasticity of demand and its measurement, Production, Factors of production, Law of variable production, Production function, Cost Analysis, Types of costs and shapes of different cost curves, Theory of Firm and Pricing, Types of markets, Equilibrium of firm and industry under perfect, Monopoly and imperfect competition.

Recommended Books:

Dessler, Human Resource Management, Pearson Rao V S P, Human Resource Management, Excel Khan M Y and Jain P K, Financial Management, Tata McGraw Hill

Pandey I M, Financial Management, Vikas Kotler Philip , Marketing Management , Pearson Kotler Philip & Armstrong Gary, Principles of Marketing ,Pearson Ahuja H L, Micro Economic Theory, S Chand Ruder Dutt & Sundharam, Indian Economy, S Chand

L T P Cr

3 1 - 4




CE-212 CONCRETE LAB



EXPERIMENTS

To determine the fineness of cement using (i) dry blank sieving (ii) blaine’s air permeability method

To determine the standard consistency, Initial and final setting time of cement sample using Vicat’s apparatus

To determine the soundness of given sample of cement and lime by i) Le Chatelier test, (ii) autoclave test.

To determine the compressive strength of cement sample.

To determine the specific gravity and water absorption of coarse aggregate.

To determine the fineness modulus and particle size distribution of coarse, Fine, And all in aggregates.

To determine the percentage bulking of a fine aggregate sample.

To determine the consistency of freshly mixed concrete of given proportion by slump test.

To determine the workability of freshly mixed concrete of given proportion by compaction factor test

To determine the cube strength and cylinder strength of concrete of given proportion and given water cement ratio.

L T P Cr

- - 2 1




CE-214 SURVEYING LAB–II



EXPERIMENTS

Study of a Theodolite

To measure the horizontal angle by the method of reiteration and repetition.

To measure vertical angle with a Theodolite

Determining Tacheometric constant of a Tacheometer.

Study and working of total station.

Distance and angular measurement by total station

Plotting a contour map with a total station

Setting out of simple circular curve by Theodolite/total station method.

L T P Cr

- - 3 1.5




CE-216 FLUID MECHANICS LAB-II



EXPERIMENTS

Study of instruments: pressure gauge - piezometer - manometer-pressure transducers - pitot tubes - current meter, Venturimeter - venturi flume - orifice meter – water meter

To study the phenomenon of cavitation in pipe flow.

To determine the critical Reynold's number for flow through commercial pipes.

Determination of friction factor for various types of pipes

To determine the coefficient of discharge for flow over a broad crested weir.

To study the characteristics of a hydraulic jump on a horizontal floor and sloping glacis including friction blocks.

To study the scouring phenomenon around a bridge pier model.

To study the scouring phenomenon for flow past a spur.

To determine the characteristics of a centrifugal pump.

To study the momentum characteristics of a given jet.

Open channel flow: determination of Manning’s coefficient and Hydraulic jump parameters

L T P Cr

- - 3 1.5




ELGA-202 ENGLISH LANGUAGE AND GENERAL AWARENESS-IV


Assumption:




grammar.

Course Objective:

The course deals with clause analysis, sentence classification based on clauses, time and

tense and common errors in sentence structure. The purpose is to familiarize students with all

kinds of sentences and their use.

Effective use of English

Unit 1: Clause analysis of a sentence

Unit 2: Classification of sentences by structure (Simple, Compound, Complex and others)

Unit 3: Synthesis of Sentences

Unit 4: How To Avoid Comma Splice, misplaced and dangling modifiers and other such mistakes

Recommended Books:

English Grammar Composition & Usage by J. C. Nesfield, published by MacMillan

India Limited, Chennai

Advanced English Grammar by Martin Hewings, published by Cambridge University

Press, New Delhi

High School English Grammar & Composition by PC Wren and H Martin, published

by S. Chand, New Delhi

L T P Cr

1 - - 1



Course Objective:

The course will help students understand the basic concepts of the Indian economy, the role

of the planning commission, India’s fiscal and monetary policy, public finance, public

distribution system and banking system.

Indian Economy

Unit-1: Planning Commission and Five Years Plan

Unit-2: Public Finance and Fiscal Policies

Unit-3: Indian Economic Set-Up { Public & Private}

Unit-4: Understanding Infrastructure for Business Set- Up

Unit-5: Legal & Financial Understanding for Business Start-Up

Recommended Books:

Datt & Sundharam, Indian Economy, S Chand





CE-301 STRUCTURAL ANALYSIS-III



Course Objective:

To acquaint students about advance methods of analysis of structure including matrix and stiffness methods. An introduction is also provided for dynamic loading of structures.

UNIT-I

Matrix analysis of structures- static and kinematic indeterminacy, Force and displacement method of analysis, Definition of flexibility and stiffness influence coefficients, Development of flexibility matrices by physical approach.

Displacement method of analysis, Definition of flexibility and stiffness influence coefficients, Development of flexibility matrices by physical approach

Flexibility method: flexibility matrices for truss and frame elements, Load transformation matrix, Development of total flexibility matrix of the structure, Analysis of simple structures plane truss and plane frame, Nodal loads and element loads, Lack of fit and temperature effects.

UNIT-II

Stiffness method- Development of stiffness matrices by physical approach, Stiffness matrices for truss and frame elements, Displacement transformation matrix, Analysis of simple structures, Plane truss and plane frame, Nodal loads and element loads, Lack of fit and temperature effects

UNIT-III

Introduction to direct stiffness method, Rotation of axes in two dimensions, Stiffness matrix of elements in global co, Ordinates from element coordinates, Assembly of load vector and stiffness matrix, Solution of two span continuous beam, Single bay single storey portal frame.

UNIT-IV

Structural dynamics, Introduction, Degrees of freedom, Single degree of freedom, Linear systems, Equation of motion, D’Alembert’s principle, Damping, Free response of damped and undamped systems, Logarithmic decrement, Transient response– Vibration isolation– Introduction to two degree of freedom systems

Recommended Books:

Chopra A K, Dynamics of structures, Pearson Education/ Prentice Hall India, 2007 Reddy C S, Basic structural analysis, Tata McGraw Hill, 2001 Wang C K, Matrix method of structural analysis, International Text Book Company, 1970 Przemeineicki J S, Theory of Matrix structural analysis, Tata McGraw Hill Coates R C and Coutie M G, Structural Analysis Gere J M and Weaver W, Matrix Analysis of framed structures, CBS Publishers Clough R W and Penzein J, Dynamics of structures, Tata McGraw Hill

L T P Cr

3 1 - 4




CE-303 TRANSPORTATION ENGINEERING-I



Course Objective:

To equip the students to plan, And design various structures and traffic control devices coming under two different modes of transportation (1) Highways and (2) Airports.

UNIT-I

Classification, Alignment and surveys, Classification of highways, Typical cross sectional roads in embankment and in cutting, Definition of various cross sectional elements, Requirements and factors controlling alignment of roads, Engineering surveys. Geometrical Design of Highways: Camber, Sight distances, Stopping, Passing and overtaking Sight distances, Overtaking zone requirements, Worked out problems, Design of horizontal alignments, Design speed, Horizontal curves, Super elevation, Super elevation design, Radius of horizontal Curve, Extra widening of pavement, Transition curves and methods of provision of super elevation and design of horizontal alignment, Design of vertical alignment, Gradient and grade Compensation Vertical curves, Summit curves, Length of summit curve, Valley curves, Length of valley curve.

UNIT-II

Traffic Engineering- Traffic Characteristics, Various traffic studies and their application traffic regulations and controls, Traffic control Devices, Traffic Signals, Classification of signals, Carriage way markings, Traffic islands, Highway intersections.

UNIT-III

Highway Materials, Testing & Design- Road aggregates, Desirable props & tests, Bituminous materials, Types of bituminous materials used in highway construction, Requirements, Desirable properties and tests. Highway construction and Maintenance- Construction of earth roads, Gravel roads WBM roads, Bituminous pavements, Bituminious construction Procedures, Construction of Cement concrete pavements. Joints in Concrete pavements – types and causes of failures in flexible and rigid pavements, Highway drainage. Pavement Design –Basic difference between flexible and rigid pavements, Factors to be considered in Design of pavements, Design of flexible pavements by CBR method only.

UNIT-IV

Aircraft characteristics– Regional planning airport site selection, Surveys for site selection Airport obstructions zoning laws, Classification of obstructions, Imaginary surfaces. Runway orientation, Wind rose diagram, Basic runway length and corrections required, Airport classification, Runway configurations. Taxiway Design requirements. Apron, Factors controlling size and number of gate positions, Aircraft parking System, Hangar site location, Facilities required in the terminal building, Blast fences, Typical airport layout, Airport marking, Airport lighting. Air traffic control, Airway aids and landing aids.

Recommended Books:

Khanna S K and Justo C.E.G., Highway Engineering, New Chand & Bros, 1991 Khadiyali L R, Traffic Engineering And Transport Planning, Khanna Publishers, 1987 Khanna S K, Arora M G and Jain S S, Airport Planning and Design, Nem Chand & Bros Rangwala S C and Rangwala P S, Airport Engineering, Charotar Publishing House, 2008 Horonjeff R, McKelvey F and Sproule W, Planning & design of airport. McGraw Hills, 2009

L T P Cr

3 1 - 4




CE-305 HYDROLOGY AND WATER POWER



Course Objective:

To make the students aware of the importance of surface water resources and strategic back ground information for its effective and wise utilization.

UNIT-I

Introduction- Hydrologic cycle, Application of hydrology in engineering– water balance equation, Water resources of India, Review of rainfall measurement and analysis. Abstraction from precipitation, Evaporation– measurement, Estimation and control of evapo-transpiration

(ET), Estimation of evapo-transpiration, Evapo-transpiration and consumptive use, Measurement of ET, Lysimeters and field pots, Potential ET and its computation, Pan evaporation, Pennman’s method, Blaney Criddle method, Reference crop ET and crop coefficient, Interception and depression storage, Infiltration processes, Measurement using infiltrometers, Infiltration capacity, Infiltration indices, Hortan’s model of infiltration. Rain water harvesting, Methods of water conservation

UNIT-II

Characteristics of runoff, Factors affecting run off, Components of hydrograph, Base flow separation, Rain fall, Run off relations, Unit hydrograph theory, Derivation of unit hydrograph, Applications and limitations of unit hydrograph, S-hydrograph, Instantaneous unit hydrograph, Unit hydrograph for ungauged catchments, Synthetic hydrograph, Conceptual elements, Linear reservoirs, Nash model. Yield from a catchment, Flow duration curves, Flow mass curve.

UNIT-III

Floods- estimation of peak discharge, Rational method, Unit hydrograph method. Probabilistic and statistical methods, Basic concept of probability and frequency distribution, Skewness coefficient, Return period discrete distribution, Binomial distribution, Continuous distribution, Flood frequency analysis, Normal, Lognormal, Gumbel and Log, Pearson Type III methods.

Flood routing, Reservoir routing, Modified pulse method, Channel routing, Muskinghum method.

UNIT-IV

Water power- types of hydro power schemes, Runoff river plant, Pumped storage plant, Tidal power plants, Hydro power potentials of India, Economic considerations of water power, Estimates of available water power, Gross and net head, Available power, Power duration curve, Assessment of water power potential, Load factor, Capacity factor, Utilization factor, General layout of hydro power scheme, Elements of hydro power scheme, Intakes, Functions, Types, Tail race, Penstocks: location, Types, Economical diameter, Penstock accessories, Anchor block, Water hammer, Water hammer equation, Cavitations, Surge Tanks.

Recommended Books:

Subramanian K, Engineering Hydrology, Tata McGraw Hill, 2008

Wilson E M, Engineering Hydrology, Macmillan, 1990. Raghunath H M, Hydrology: principles, analysis, Design, Prentice Hall, 2007 Punmia B C, Lal P B B and Jain A K, Irrigation and Water Power Engineering, Laxmi

Publication, 2009.

L T P Cr

3 1 - 4




CE-307 SOIL MECHANICS



Course Objective:

To equip the students to understand the properties and behavior of soil and various methods to determine soil properties and study of earth and earth retaining structures.

UNIT-I

Nature of soil and functional relationships: Formation of soils, Soil type, 3 phase system,void ratio, Specific gravity, Dry density, Porosity, Water content, Saturated unit weight, Submerged unit weight, Degree of saturation, Soil Structure, Single grained, Honey combed, Flocculated and dispersed structure and their effects on the basic soil properties.

Laboratory and field identification of soils- Determination of water content by oven drying, Specific gravity using pycnometer and specific gravity bottle, Grain size analysis by sieve analysis, Hydrometer analysis and pipette analysis, Atterberg limits and indices, Visual identification by simple field tests – Field density by core cutter, Sand replacement and wax coating methods. Classification of soils: Necessity, Principles of classification, I.S. classification, Plasticity charts, Group index

UNIT-II

Soil water- Modes of occurrence, Adsorbed and capillary water types, Total stress, Effective stress, Pore pressure, Pressure diagrams. Permeability- Definition, Darcy’s law, Factors affecting permeability, Laboratory determination, Stratified soils, Average permeability.

Shear Strength- Definition, Mohr’s strength and stress circles, Origin of planes, Mohr’s envelope, Mohr Coulomb strength theory, Direct shear test, Triaxial shear test, Drainage conditions, Consolidated Drained, Consolidated Undrained, Unconsolidated Undrained tests, Measurement of pore pressure, Total and effective stress strength parameters, UCC test, Vane shear tests, Choice of test conditions for field problems.

UNIT-III

Consolidation- Definition, Spring analogy for primary consolidation, Terzaghi’s theory of one dimensional consolidation, Concepts of coefficient of compressibility, Coefficient of volume change and compression index, Laboratory consolidation test, E,log p curves, Pre-consolidation pressure, Time rate of consolidation, Difference between consolidation and compaction

Compaction- Definition and objectives of compaction, Standard and Modified Proctor tests, Concept of OMC and maximum dry density, Zero air voids line, Factors influencing compaction, Effect of compaction on soil properties, Field compaction methods, Proctor needle for field control.

UNIT-IV

Earth pressure- Earth pressure at rest, Active and passive earth pressure for cohesionless and cohesive soils, Rankine’s and Coulomb’s theories, Point of application of earth pressure for cases of with and without surcharge in cohesionless and cohesive soils, Culmann’s and Rebhan’s graphical construction for active earth pressure, Stability of slopes: Slope failure, Base failure and toe failure, Swedish circle method – Φ = 0 analysis and c = 0 analysis, Friction circle method, Taylor’s stability number – Stability charts.

Recommended Books:

Arora K R, Soil Mechanics & Foundation Engineering, Standard Publications, 1987 Punmia B C, Soil Mechanics & Foundations, Laxmi Publications, 1988 Murthy V N S, Soil Mechanics & Foundation Engineering, Dhanpat Rai, 1996

L T P Cr

3 1 - 4




CE-309 PROJECT PLANNING & MANAGEMENT



Course Objective:

To make the students familiar with the various facets of construction and its planning like project scheduling, Resource and material management and construction procedures.

UNIT-I

Significance of construction management, Objectives and functions of construction management, Types of constructions, Resources for construction industry, Stages for construction, Construction team, Engineering drawings.

Introduction to type of Construction Contracts & Specifications, Types of contracts, Contract document, Specifications, Important conditions of contract, Arbitration.

UNIT-II

Introduction to construction planning, Work breakdown structure, Stages in planning, Pre-tender stages, Contract stage, Scheduling, Scheduling by bar charts, Preparation of material, Equipment, Labour and finance schedule, Limitation of bar charts, Milestone charts.

Principles of construction Organization, Communication, Leadership and human relations, Types of Organizations, Organization for construction firm, Site organization, Temporary services, Job layout.

UNIT-III

Introduction, Network techniques in construction management, CPM, Work break down, Classification of activities, Rules for developing networks, Network development, Logic of network, Allocation of time to various activities, Fulkerson's rule for numbering events, Network analysis, Determination of project schedules, Critical path, Ladder construction, Float in activities, Shared float, Updating, Resources allocation, Resources smoothing and resources leveling.

Introduction to inspection & quality Control, Principles of inspection, Enforcement of specifications, Stages in inspection and quality control, Testing of structures, Statistical analysis.

UNIT-IV

PERT, Probability concept in network, Optimistic time, Pessimistic time, Most likely time, Lapsed time, Deviation, Variance, Standard deviation, Slack critical path, Probability of achieving completion time, Central limit theorem.

Cost, Time Analysis Cost versus time, Direct cost, Indirect cost, Total project cost and optimum duration, Contracting the network for cost optimisation, Steps in time cost optimisation, Illustrative examples.

Recommended Books:

Punmia B C and Khandelwal K K, Project Planning & Control with PERT & CPM, Lakshmi Publication, 2002

Srinath L S, PERT and CPM: Principles & Applications, Affiliated East-west Press(P)Ltd, 1975

Sengupta B and Guha H, Construction Management and Planning, Tata McGraw Hills

L T P Cr

3 1 - 4




CE-311 ENVIRONMENTAL ENGINEERING-I



Course Objective:

To provide detailed understanding regarding usage of water for drinking purpose – from identification of source, Planning the treatment systems, Distribution of treated water with development of distribution of layout and necessity of maintenance.

UNIT-I

Water supply Engineering: Importance and necessity of community water supply schemes, Essentials of water supply engineering, Quantity of water, Forecasting population, Rate of consumption for various purposes, Factors affecting consumption, Fluctuations in demand.

UNIT-II

Sources of water, Surface water sources, Suitability of the source with respect to quantity and quality, Intakes of various surface water sources, Design of intakes, Ground water sources, Development and protection of groundwater sources, Estimation of yield from various ground water sources, Construction of tube wells, Maintenance. Quality of water, Drinking water standards, Physical, Chemical and bacteriological analysis of water.

UNIT-III

Treatment of water- aeration, Coagulation, Flocculation, Sedimentation, Design of sedimentation tanks, Filtration- slow and rapid filter design, Disinfection, Design of all the units of water treatment plant, Miscellaneous treatments- removal of colour, Taste and odor, Iron and manganese, And hardness, Fluoridation and deflouridation.

UNIT-IV

Water supply schemes, Gravitational, Pumping and combined schemes, Transmission of water, Classification of conduits, Shape and strength of conduits, Location of conduits, Materials of conduits, Design of gravity and pumping main, Distribution systems, Different layout of pipe networks, Analysis of pipe networks, House connection from mains, Laying and joining of pipes, Appurtenances, Different valves, Meters and hydrants, Detection and prevention of leaks in distribution system, Cleaning and maintenance of distribution system.

Recommended Books:

Garg S K, Environmental Engineering Vol I, Khanna Publishers, 1992

Birdie G S and Birdie J S, Water Supply and Sanitary Engineering, Dhanpat Rai & Sons, 1996

Duggal K N, Elements of Environmental Engineering, S Chand & Co Ltd, 2008

L T P Cr

3 1 - 4




CE-313 COMPUTER APPLICATIONS LAB



EXPERIMENTS

All experiments should be performed using STAAD or Equivalent package

Analysis of multi-span Beam and frames using stiffness matrix method.

Analysis of Plane frame and space Frame.

Analysis & Design of truss system.

Analysis & Design of steel frames.

Analysis & Design of RC frame.

Analysis & Design of combined steel truss and RC frame (Auditorium)

Design of footings

Analysis of a three storeyed and ten storeyed building.

L T P Cr

- - 2 1




CE-315 TRANSPORTATION ENGINEERING LAB-I



EXPERIMENTS

Aggregate Impact Test.

Los-Angeles Abrasion Test on Aggregates.

Dorry's Abrasion Test on Aggregates.

Deval Attrition Test on Aggregates.

Crushing Strength Test on Aggregates.

Penetration Test on Bitumen.

Ductility Test on Bitumen.

Viscosity Test on Bituminous Material

Softening Point Test on Bitumen.

Flash and Fire Point Test on Bitumen.

L T P Cr

- - 2 1




CE-317 SOIL MECHANICS LAB-I



EXPERIMENTS

Determination of water content by oven drying method

Determination of specific gravity by pycnometer

Determination of field density and dry unit weight by core cutter method

Determination of field density by sand replacement method

Determination of grain size distribution by sieve analysis

Determination of grain size distribution by hydrometer analysis

Determination of liquid limit of soil

Determination of plastic limit of soil

Determination of compaction properties of soil by standard proctor test

Determination of shear parameters of soil by direct shear method

L T P Cr

- - 2 1




CE-319 ENVIRONMENTAL ENGINEERING LAB-I



EXPERIMENTS

To determine the turbidity in a given water sample.

To determine the pH value of a given sample of water.

To determine the true colour unit(TCU) in a given sample of water.

To determine the conductivity of a given water sample.

To determine the chloride concentration in a given sample of water.

To determine the optimum coagulant dose.

To determine temporary and permanent hardness in a given water sample.

To determine the chloride dose required for a given water sample.

To determine the dissolved oxygen (D.C) in a given sample of water.

To determine the MPN coliform per 100 ml of a given sample of water.

To determine the total plate count of a given water sample.

L T P Cr

- - 2 1




ELGA-301 ENGLISH LANGUAGE AND GENERAL AWARENESS-V


Assumption:




grammar.

Course Objective:

The course facilitates the learning of the principles of effective formal and business

communication.

Using English For Business Purpose (Level 1)

Unit 1: Use of Phrasal Verbs In Business English

Unit 2: Improving Word Skill For the Internal Communication

Unit 3: Writing Notice, Agenda and Minutes of Meeting

Unit 4: Writing Effective Business Letters

Unit 5: Writing Effective Report

Recommended Books:

English Phrasal Verbs in Use, Michael McCarthy, Felicity O’Dell, Cambridge University Press, 2008.

Oxford Word Skills, Ruth Gairns and Stuart Redman, Oxford University Press, 2009.

English Vocabulary in Use, Michael McCarthy, Felicity O’Dell, Cambridge University Press, 2008. Business Communication Today, Coutland L. Bovee and John V. Thill, Dorling Kindersley (India) Private Limited, New Delhi, 2005.

Business Communication, Raymond V Lesikar, Marie E Flately, Kathryn Rentz, Neerja Pandey, Tata McGrawa Hill Education Pvt Ltd, New Delhi, 2009.

L T P Cr

1 - - 1



Course Objective:

The course is designed to familiarize students with the developments in the fields of science,

defence, space, sports and cinema. The course will also help students in develop general

mental ability

General Studies {Miscellaneous}

Unit 1: Indian Defence and Scientific Advancement

Unit 2: Indian Missile and Space Programme

Unit 3: Major Scientific Discoveries and Theories

Unit 4: Sport Diary and Cinemas{ Hollywood & Bollywood}

Unit 5: General Mental Ability

Recommended Books:


India 2010 – A Reference Manual, Publication Division, New Delhi Manorma Year Book -2012, Mammen Matthew, Malayalam Manorama , Kottayam




CE-302 DESIGN OF STEEL STRUCTURES-II



Course Objective:

To provide detailed understanding of design of industrial building, Water tanks and towers etc. Students will be allowed to use plastic analysis methods of steel structures.

UNIT-I

Elementary Plastic Analysis and Design, Introduction, Scope of plastic analysis, Ultimate load carrying capacity of tension members and compression members, Flexural members, Shape factor, Mechanisms, Plastic collapse, Analysis, Plastic analysis applied to steel beams and simple portal frames and design.

UNIT-II

Industrial Buildings, Loads, General arrangement and stability, Design considerations, Design of purlins, Design of roof trusses, Industrial building frames, Bracings and stepped columns.

UNIT-III

Design of Water Tanks, Permissible stresses, Design of circular, Rectangular and pressed steel tanks including staging.

Design of Steel Stacks, Introduction, Various loads to be considered for the design of steel stacks, Design of steel stacks including foundation.

UNIT-IV

Design of Towers, Transmission line towers, Microwave towers, Design loads, Classification, Design procedure and specification.

Cold Formed Sections, Introduction and brief description of various types of cold formed sections, Local buckling, Concepts of effective width and effective sections, Elements with stiffeners, Design of compression and bending elements.

Recommended Books:

Arya A S and Ajmani J L, Design of Steel Structures, Nem Chand & Bros., Roorkee Dayartnam P, Design of Steel Structures, S. Chand and company, 2008 IS:800,1984, Indian Standard Code of Practice for General Construction in Steel IS:801,1975, Indian Standard Code of Practice for Use of Cold formed light gauge steel

structural members in general building construction

L T P Cr

3 1 - 4




CE-304 GEOTECHNOLOGY



Course Objective:

To impart knowledge in behaviour and design aspects of various types of foundations as well as slope analysis and soil improvement.

UNIT-I

Types of shallow foundations and their relative merits, Depth of foundation, Footing on slopes, Uplift of footings, Conventional procedure of proportioning of footings, Combined footings, Raft foundations, Bearing capacity of raft in sands and clays, Various methods of designing rafts, Floating foundations. Design criteria for structural safety of foundation (i) location of footing,(ii) shear failure criterion, (iii) settlement criterion, Ultimate bearing capacity, Modes of shear failure, Rankine's analysis Tergazi's theory, Skempton's formula, Effect of fluctuation of ground water table, Effect of eccentricity on bearing capacity, Inclined load, I.S Code recommendations, Factors affecting bearing capacity, Methods of improving bearing capacity. Plate load test and its interpretation, Bearing capacity from penetration tests, Design bearing capacity.

UNIT-II

Introduction to pile foundation, Necessity of pile foundations, Classification of piles, Load capacity, Static analysis, Analysis of pile capacity in sands and clays, Dynamic analysis, Pile load tests, Negative skin friction, Batter piles, Lateral load capacity, Uplift capacity of single pile, Under-reamed piles

Group action in piles, Pile spacing, Pile group capacity, Stress on lower strata, Settlement analysis, Design of pile caps, Negative skin friction of pile group, Uplift resistance of pile group, Lateral resistance, Batter pile group.

UNIT-III

Stability of slopes- causes of failure, Factors of safety, Stability analysis of slopes, Total stress analysis, Effective stress analysis, Stability of infinte slopes types of failures of finite slopes, Analysis of finite slopes, Mass procedure, Method of slices, Effect of pore pressure, Fellinius method to locate centre of most critical slip circle, Friction circle method, Tayler's stability number, Slope stability of earth dam during steady seepage, During sudden draw down and during and at the end of construction.

UNIT-IV

Soil improvement, Shallow compaction, Mechanical treatment, Use of admixtures, Lime stabilization, Cement stabilization, Lime fly ash stabilization, Dynamic compaction and consolidation, Bituminous stabilization, Chemical stabilization, Pre- compression, Lime pile and column, Stone column, Grouting, Reinforced earth.

Recommended Books:

Ranjan G and Rao A S R, Basic and Applied Soil Mechanics, New Age Int.(P)Ltd, 2007 Prakash S, Ranjan G and Saran S, Analysis and Design of Foundation and Retaining

Structures by Sarita Prakashan Saran S, Analysis and Design of Sub Structures, IBH Oxford, 2006 Das B M, Principles of Foundation Engineering, Cengage Learning, USA, 2010 Bowles J E, Foundation Analysis and Design, McGraw Hills, 1988

L T P Cr

3 1 - 4




CE-306 TRANSPORTATION ENGINEERING–II



Course Objective:

To acquaint students about various concepts required in the design and operation of railways and to have a clear picture about the details of design, Construction and maintenance of structures like harbor and docks.

UNIT-I

Railway Engineering: Permanent way, Main requirements, Component parts. Rails, Functions of rails, Requirements of a good rail, Weight and length., Defects in rails, Rail joint and other fastenings, Check and guard rails, Coning of wheels, Creep of rail. Sleeper, Its functions and requirements, Types of sleepers, Sleeper density. Ballast, Functions and requirements, Different types of ballast used. Geometric Design: Design of horizontal curves, Super elevation, Negative super elevation in branches, Length of transition curves, Grade compensation on curves, Widening of gauge on curves.

UNIT-II

Railway Operation control: Points and Crossings, Design features of a turn out, Types of railway track points –Details of station yards and Marshalling yards, Signaling and interlocking, Principles of track circuiting, Control of train movement by absolute block system, Automatic block system, Centralized traffic control systems. Tunnel Engineering: Tunnel sections, Types size and shapes, Tunnel surveying, Alignment, Transferring center grade in to tunnel, Tunnel driving procedure, Tunneling through hard and soft soils(Only Full face Method and Needle Beam Method),Tunnel lining ventilation lighting and drainage of tunnels.

UNIT-III

Harbor Engineering: Classification of harbours, Breakwaters, Necessity and functions, Different types, Forces acting on breakwater, Design principles, Construction of breakwaters, General study of pier heads, Quays, Landing stages, Wharves, Jetties, Transit sheds and warehouses channel demarcation, Signal characteristics Beacons, Buoys, Channel, Lighting, Light houses).

UNIT-IV

Dock Engineering Function and types of docks, Dry docks, Floating docks slipways, Dock gates and caissons, Dredging, Mechanical and hydraulic dredgers, General study of bucket ladder, Dredger, Grab dredger and dipper dredgers.

Recommended Books:

Rangwala S C, Railway Engineering, Charator Publishing House, 2008 Chandra S and Agarwal M M, Railway Engineering, Oxford University Press, 2007 Arora S P and Saxena S C, Railway Engineering, Dhanpatrai & Sons, 2001 Bindra S P, A Course in Docks & harbor Engineering, Dhanpatrai & Sons, 1992

L T P Cr

3 1 - 4




CE-308 ENVIRONMENTAL ENGINEERING-II



Course Objective:

To expose students to the area of waste treatment – with emphasis on domestic liquid wastes – its characterization, Collection, Treatment and disposal at individual household level to community level (rural and urban). To impart the basic concepts of solid waste management and air pollution control.

UNIT-I

Importance of sanitation, Systems of sewerage– separate, Combined and partially separate. Quantity of sanitary sewage and variations. Shapes of sewer – circular and egg shaped. Design of sewers, Self-cleansing velocity and slopes, Construction and testing of sewer lines. Sewer materials. joints and appurtenances.

Quality parameters of sewage, BOD, COD, Solids, D.O., Oil & Grease. Indian Standards for disposal of effluents into inland surface sources and on land.

UNIT-II

Objectives of wastewater treatment, Effluent standards, KSPCB Standards, BIS Standards. Layout of conventional treatment plant, Preliminary, Primary, Secondary and tertiary treatments in general. Preliminary process- screens, Types of screens, Design, Disposal of screenings, Grit chamber and its function, Design, Construction and operation, Disposal of grit, Detritus tank, Skimming tank and its function, Design and operation, Disposal of skimming Sedimentation: Theory of sewage sedimentation, Design construction and operation, Rectangular and circular tanks, Disposal of sludge.

UNIT-III

Biological process- principle and theory of biological treatment. Sewage filtration; trickling filters, Design, Construction and operation. Activated sludge process: Design, Construction and operation of conventional and extended aeration, Aeration methods. Miscellaneous methods, Stabilization ponds, Oxidation ditch, Aerated lagoons, Rotating biological contactors; disinfection of sewage effluents.

UNIT-IV

Sludge treatment and disposal- quantity of sludge, Characteristics of sludge, Sludge thickening, Digestion, Conditioning and disposal, Design of sludge digesters only. Septic Tanks: Design (as per Ministry of urban development) construction, Disposal of effluents, Cleaning of tanks, Imhoff tanks. Sewage treatment by high rate anaerobic methods: Anaerobic digestion suspended growth, Contact process, UASB, Attached growth, Filters, Expanded bed, Only basics.

Recommended Books:

Garg S K, Sewage Disposal and Air Pollution, Khanna Publishers, New Delhi, 1996 Punmia B C, Jain A K, Jain A K, Waste Water supply Engineering, Laxmi Publication, 2005 Metcalf and Eddy, Waste water Engineering 4th Ed., McGraw Hill International Editions,

2003 Hammer M J, Water and waste water technology, John Wiley and Sons, Inc., 2011

L T P Cr

3 1 - 4




CE-310 IRRIGATION ENGINEERING



Course Objective:

Students are expected to realize the importance of water resources and its application in irrigation engineering

UNIT-I

Introduction- Need, Advantages and disadvantages of Irrigation, Environmental effects, Types of Irrigation systems, Gravity irrigation, Canals, Tanks, Wells and Irrigation galleries, Water lifts. Soil,water, Plant relationship: Soil and its function, Physical properties of soil and their importance in relation to irrigation, Classes and availability of soil water, Movement of water in soils, Measurement of soil moisture, Crop growth and moisture relationship, Salt problems in soil and effect of salts on plant growth.

UNIT-II

Classification of canals- design of canals, Erodible canals, Canals in alluvial soils, Regime theory, Component of canal distribution system, Alignment of channels, Losses in irrigation channels, Design discharge, Silt theories and design of alluvial channels, Comparison of Kennedy's and Lacey's theories, Manning’s formula, Canal section and design procedure, Garrets and Lacey's diagrams.

Irrigation Requirement- Evaporation, Evapo transpiration, Consumptive use and its estimation – Crop factor, Lysimeters, Effective rain fall and irrigation requirements, Water requirements of various crops, Duty of water, Quality of irrigation water.

UNIT-III

Occurrence, Distribution of ground water, Darcy’s law, Permeability, Safe yield, Location and development of ground water supplies, Hydrology of well, Steady flow in confined and unconfined aquifers, Open well, Yield of an open well, Effect of partial penetration, Interference of wells, Boundary effect, Specific capacity of well, Tube wells, Yield from a tube well, Strainers, Site for a tube well Flow and lift Irrigation, Perennial and Inundation irrigation, Important Crops and crop seasons, Duty and delta, Method of Cultivation, Water requirement, Irrigation efficiency, Multipurpose projects. Reservoirs- Investigation and planning, Selection of site, Engineering, Geological, And hydrological Investigations, Fixation of storage capacity, Contours, Mass curve, Operation of reservoirs, Reservoirs sedimentation.

UNIT-IV

Head works- Storage and diversion works, Layout of head works, Selection of site, Weirs, Types of weirs, Weirs on permeable foundation, Uplift and piping, Bligh’s creep theory, Lane’s weighted creep theory, Khosla’s theory of independent variables, Design of aprons, Body wall, Vertical drop weir, Design of sloping glacis weir. River regulators, Silt excluder, Silt vane. Spillways- Type and Functions, Design of Ogee Spillway and Siphon Spillway, Energy dissipation below spillways, Stilling basin, Spillway crest gates, Distribution works.

Recommended Books:

Punmia B C, Lal P B B and Jain A K, Irrigation and Water Power Engineering, Laxmi Publication, 2009

Modi P N, Irrigation Water Resources & Water Power, Standard Book House, 2008 Garg S K, Irrigation Engineering and Hydraulic Structures, Khanna Publishers, 2009

L T P Cr

3 1 - 4




CE-312 DESIGN OF CONCRETE STRUCTURES-II



Course Objective:

To provide knowledge in the structural Design of selected advanced structures of concrete

UNIT-I

Continuous Beams- Basic assumptions, Moment of inertia, Settlements, Modification of moments, Maximum moments and shear, Beams curved in plan, Analysis for torsion, Redistribution of moments for single and multi, Span beams, Design examples.

Flat slabs and staircases, Advantages of flat slabs, General design considerations, Approximate direct design method, Design of flat slabs, Openings in flat slab, Design of various types of staircases, Design examples.

Foundations, Combined footings, Raft foundation, Design of pile cap and piles, Under- reamed piles, Design examples.

UNIT-II

Water Tanks, Silos and Bunkers, Estimation of Wind and earthquake forces, Design requirements, Rectangular and cylindrical underground and overhead tanks, Intze tanks, Design considerations, Design examples.

UNIT-III

Silos and Bunkers, Various theories, Bunkers with sloping bottoms and with high side walls, Battery of bunkers, Design examples.

Prestressed Concrete, Basic principles, Classification of prestressed members, Various prestressing systems, Losses in prestress, Initial and final stress conditions, Analysis and design of sections for flexure and shear, Load balancing concept, IS Specifications.

UNIT-IV

Building Frames, Introduction, Member stiffnesses, Loads, Analysis for vertical and lateral loads, Torsion in buildings, Ductibility of beams, Design and detailing for ductibility, Design examples.

Yield Line Theory, Basic assumptions, Methods of analysis, Yield line patterns and failure mechanisms, Analysis of one way and two way rectangular and non- rectangular slabs, Effect of top corner steel in square slabs, Design examples.

Recommended Books:

Krishna J and Jain O P, Plain and Reinforced Concrete, Vol.II, Nem Chand & Bros., Roorkee Krishna R N, PreStressed Concrete, TMH Publications, New Delhi, 2006 Lin T Y Design of Prestressed Concrete Structures, John Wiley & Sons, 1981 Jain A K, Reinforced Concrete- Limit State Design, Nem Chand & Bros., Roorkee IS 1343, 1980, IS Code of Practice for Prestressed Concrete

IS 3370, 1976(Part I to IV), Indian Standard Code of Practice for Liquid Retaining Structures

L T P Cr

3 1 - 4




CE-314 TRANSPORTATION ENGINEERING LAB–II



EXPERIMENTS

Flakiness and Elongation Index of aggregates.

Specific gravity and water absorption test on aggregates.

Specific gravity of bitumen.

Proportioning of aggregates.

Marshall’s stability test.

Stripping test on aggregates.

Determination of bitumen content.

CBR lab test on soil.

Traffic volume study using videography technique.

Traffic speed study using videography technique.

L T P Cr

- - 2 1




CE-316 ENVIRONMENTAL ENGINEERING LAB-II



EXPERIMENTS

To determine the acidity and alkalinity of a sewage sample.

To determine total, Suspended, Dissolved and settable solids in a sewage sample.

To determine volatile and fixed solids in a sewage sample.

To determine oil and grease in a sewage sample.

To determine the chloride and sulphate concentration in a sewage sample.

To determine the B.O.D. of a given sewage sample.

To determine the C.O.D. of a given sewage sample.

To determine the T.O.C. of a given sewage sample.

To determine the fecal count of a given sewage sample

L T P Cr

- - 2 1




CE-318 SOIL MECHANICS LAB-II



EXPERIMENTS

Test to determine Atterberg limit

Direct Shear and Tri-axial Compression tests

Lab Vane shear test

Cyclic Tri-axial test

In-situ field density test

Light cone penetration test

Instrumentation for field monitoring: Pressure pad, Settlement gauge, Piezometer: Vibration measurement.

L T P Cr

- - 2 1




CE-320 SEMINAR


SEMINAR

Each one of the students will be assigned to work on a Seminar Topic in the current and advanced areas of civil engineering, Including application of other engineering disciplines in civil engineering. The student has to

conduct a detailed literature review on the assigned topic and prepare a report. The student will make an oral presentation followed by a brief question and answer session. The Seminar (including presentation and report) will be evaluated by the faculty members assigned for this purpose.

L T P Cr

- - 2 1




ELGA-302 ENGLISH LANGUAGE AND GENERAL AWARENESS-VI


Assumption:




grammar.

Course Objective:

The purpose of the course is to make the students confident of using English in formal as well

as informal communication for business and all other purposes.

Using English for Business Purpose (Level 2)

Unit-1: English in informal conversation vs. formal communication

Unit-2: Use of effective words in business and marketing communication

Unit-3: Framing questions and model answers for use in Interviews for

different purposes

Unit-4: Learning the right words and framing effective sentences to succeed

in Group Discussion, Meetings And Conference Call (Discussion and

exercise based on such situations)

Unit-5: Glossary of words, along with their various usage, related to topics

to economic, political, social and legal issues which can come in handy to

students

Recommended Books:

1. Effective English Communication, Krishna Mohan and Meenakshi Raman, Tata Mc Graw- Hill

Publishing company Ltd, New Delhi.

2. A communicative grammar for English, Geofferey Leech and Jan Svartvik, Pearson Longman,

New Delhi.

3. Word Perfect Spelling, Ronald Ridout, Oxford University Press, New Delhi.

4. 30 Days to a More Powerful Vocabulary, Wilfred Funk and Norman Lewes, Binny Publication

House, Delhi.

5. A senior English Grammar and composition N.K.Agarwala, Goyal Brother Prakashan, New Delhi

L T P Cr

1 - - 1



Course Objective:

The purpose of the course is to provide information on the basic concepts of

entrepreneurship, IT, and business infrastructure and related legal concepts. Besides, this

course also aims at familiarizing student with energy technologies and functioning of human

body.

General Science

Unit-1: Advance Communication System

Unit-2: Fuels and Combustion

Unit-3: Energy Audit and Conservation

Unit-4: Renewable Energy Technologies

Unit-5: Human Body

Recommended Books:

M. P. Murgai and Ram Chandra, ‘Boiler Operation’, New Age International

Publishers, New Delhi, 2000

Reader’s Digest




CE-421/422/423/424 QUANTITY SURVEY AND VALUATION



Course Objective:

The student should be able to set out any civil engineering work, To prepare detailed exact as well as approximate estimates, To have a thorough idea regarding the quality and quantity of materials, To calculate the exact quantities of items of work and to prepare valuation report of real and landed property.

UNIT-I

Estimate– Basic terms, Types of estimate, Revised estimate– supplementary estimate, Maintenance estimate, Approximate estimate, Plinth area method– cubic rate method, Unit rate method, Bay method, Approximate quantity from bill method, Comparison method, Cost from materials and labour etc., Preparation of detailed estimate for buildings, Centre line method and long wall, Short wall method.

UNIT-II

Methods of measurements of different items of work, Preparation detailed estimate for sanitary and water supply works, Roads, Irrigation works, Steel structures– doors and windows, R C C Structures, Preparation of bar bending schedule.

UNIT-III

Detailed specifications for common building materials and items of work as per I.S specifications, Preparation of conveyance statement, Calculation of quantities of materials for items of work, Analysis of rate for items of works required for civil engineering works, Preparation of abstract of estimate of civil engineering works.

UNIT-IV

Valuation, Explanation of items, Types of values, Sinking fund, Years purchase, Depreciation, Straight line method, Constant percentage method, S.F method, Obsolescence, Valuation of real property, Rental method, Profit based method, Depreciation method, Valuation of land, Belting method, Development method, Hypothecated building scheme method, Rent calculation, Lease and lease hold property.

Recommended Books:

Vazirani V N and Chandola S P, Civil engineering estimating & costing, Khanna Publishers, 2004

Dutta B N, Estimating and Costing in Civil Engineering: Theory and Practice, Sangam Books, 2002

Rangawala S C, Valuation of real properties, Charotar Publishing House Pvt. Ltd., 2008

L T P Cr

3 1 - 4




CE-421/422/423/424 PRESTRESSED CONCRETE STRUCTURES



Course Objective:

To understand design and analysis principle of pre-stress concrete and study the behaviour of different pre-stressed components in detail.

UNIT-I

General principles of prestressed concrete – classification and types, Stages of loading, Advantages of prestressed concrete over reinforced concrete, Partial prestressing, Design codes for prestressed concrete Materials, Strength requirements of concrete, Strain characteristics of concrete, Special manufacturing techniques of concrete, Self stressing cement, Steels for prestressing, Steel wires, Steel strands, Steel bars, Fiberglass tendons, Grouts.

UNIT-II

Prestressing systems and end anchorages- pre-tensioning system and end anchorages, Tensioning methods in post-tensioning, Post-tensioning anchorages utilizing wedge action, Post-tensioning anchorages for wires, Post-tensioning anchorages for bars

Loss of prestress- Significance, Lump sum estimate, Elastic shortening of concrete, Time dependent losses, Loss due to creep of concrete, Loss due to shrinkage of concrete, Loss due to steel relaxation, Loss due to anchorage take up, Loss or gain due to bending of members, Practical considerations for frictional loss, Theoretical considerations for frictional loss, Total amount of losses elongation of tendons

UNIT-III

Analysis of sections for flexure- Stresses in concrete due to prestress, Stresses in concrete due to loads, Stresses in steel due to loads, Discussion on moment curvature relationship of a prestressed concrete beam Design of sections for flexure-Preliminary design, General concepts of elastic design, Elastic design with no tension in concrete, Elastic design allowing tension, Elastic design allowing and considering tension, Ultimate design, Arrangement of steel and prestressing in stages

UNIT-IV

Limit state design of prestressed concrete sections- strength and serviceability limits state, Crack widths in prestressed members, Design of section for flexure, Design of section for shear and torsion, Design of member for bond, Design of member for bearings Design of pre-tensioned and post-tensioned flexural beam- dimensioning of flexural members, Estimation of self weight of beam, Design of pre-tensioned beam, Design of post-tensioned beam, Design of partially prestressed beam.

Recommended Books:

Lin T Y and Burns N H, Design of prestressed concrete structures, John Wiley & Sons, New York, 1981

Raju N K, Prestressed concrete, Tata McGraw Hill Publishing Company Limited, New Delhi, 2006

Nawy E G, Prestressed Concrete: A Fundamental Approach, Pearson Education, Limited, 2011

L T P Cr

3 1 - 4




CE-421/422/423/424 GROUND IMPROVEMENT TECHNIQUES



UNIT-I

Objective of ground improvement, In-situ ground improvement methods. Introduction to soil improvements without the addition of many material, Surface compaction, Compaction piles in sand impact compaction/dynamic compaction of sands, Vibratory compaction in sand vibro-flotation in sand, Explosions in sand, Terra probe method, Replacement process, Vibro-flotation in clays, Preloading techniques, Sand drains, Stone columns, Introduction to soil improvement by thermal treatment, Introduction to bio technical stabilization.

UNIT-II

Introduction to soil improvement by adding materials, Lime stabilization, Mechanism optimum lime content, Lime fixation point-effect of lime on physical and engineering properties of soil, Lime column method, Stabilization of soft clay or silt with lime, Stabilization with cement, Suitability for soils, Effect on properties of soils Grouting, Types, Desirable characteristics of grouts, Grouting methods, Grouting pressure, Grouting materials, Grouting technology, Permeation grouting, Compaction grouting, Soil fracture grouting, Jet grouting, Application and limitations, Slab jacking, Grouted columns application to dams.

UNIT-III

Soil improvement using reinforcing elements, Introduction to reinforced earth, Load transfer mechanism and strength development, Soil types, Reinforcing materials, Reinforced earth retaining walls, Reinforced embankments, Soil nailing,improvement using natural materials.

UNIT-IV

Geosynthetics, Types, Applications (only general applications), Types of geotextiles and geo grids, Physical and strength properties of geotextiles and geogrids, Behaviour of soils on reinforcing with geotextiles and geogrids, Design aspects with geotextiles and geogrid for clay embankments, Retaining walls and unpaved roads.

Recommended Books:

Purushotham S R, Ground Improvement Technique, Laxmi Publications, 2005 Rao G V and Rao G V S, Text Book on Engineering with Geotextiles, Tata McGraw Hill Ortigão J A R and Sayao A S F J, Handbook of slope stabilization, Springer, 2004 Jewell R A, Text Book on Soil Reinforcement with Geotextiles, CIRIA Special Publication,

Thomas Telford Gray Donald H and Sotir Robbin B, Text Book on Bio Technical & Soil Engineering Slope

Stabilization, John Wiley, 1996

Course Objective:

L T P Cr

3 1 - 4




CE-421/422/423/424 SOLID AND HAZARDOUS WASTE MANAGEMENT



Course Objective:

This course will help students to learn about various types of solid wastes, Their proper disposal and management.

UNIT-I

Types and Sources of solid and hazardous wastes - Need for solid and hazardous waste management, Elements of solid waste management, Salient features of Indian legislations on management and handling of municipal solid wastes, Hazardous wastes.

UNIT-II

Waste generation rates and variation - Composition, Physical, Chemical and biological properties of solid wastes, Hazardous Characteristics, Source reduction of wastes, Recycling and reuse.

UNIT-III

Handling and segregation of wastes at source – storage and collection of municipal solid wastes, Analysis of Collection systems, Transfer and transport, Compatibility, Storage, Labeling and handling of hazardous wastes, Hazardous waste manifests and transport.

UNIT-IV

Objectives of waste processing– material separation and processing technologies, Methods and controls of Composting, Incineration, Solidification and stabilization of hazardous wastes

Waste disposal options, Disposal in landfills, Landfill Classification, Types and methods, Site selection, Design and operation of sanitary landfills, Secure landfills

Recommended Books:

George Tchobanoglous, Hilary Theisen and Samuel A, Vigil. Integrated Solid Waste Management, McGraw- Hill International edition, New York, 1993

CPHEEO, Manual on Municipal Solid waste management, Central Public Health and Environmental Engineering Organisation, Government of India, New Delhi, 2000

Micheael D. LaGrega, Philip L Buckingham, Jeffrey C. E vans, Environmental Resources Management, Hazardous waste Management, McGraw-Hill International edition, New York, 2001

Vesilind P.A., Worrell W and Reinhart, Solid waste Engineering, Thomson Learning Inc., Singapore, 2002

L T P Cr

3 1 - 4




CE-421/422/423/424 HYDRO POWER ENGINEERING



UNIT-I

History and types of water power development: History of water power development, Water power development in India, Comparison of water power with thermal, Nuclear and wind mills, Classification, High, Medium and Low Head schemes, Run off river plants, Storage power station Tidal power plant,Recent experiences in wave power development, Underground power plants, Pumped storage schemes, Small and mini Hydropower systems, Power demand, Role of Hydropower in a grid.

UNIT-II

Planning and Layout of Hydropower schemes: Investigation connected with hydropower development, Site selection, Layout of hydro power plant, Capacity, Load factor and Load curve.

Mini Hydropower Systems: Small and min hydropower systems - Site selection, Hydrologic computations, Site development, Environmental Impact, Economic and Financial Feasibility.

UNIT-III

Design of Hydroelectric works: Necessities for the construction of a dam, Selection of type of Dam, Spillway, Types and design, In take works, Types - Design of Intake transition, Trashrack, Design of power canals and penstocks, Penstock joints support structures, Elements of laying penstock lines, Water hammer, Rigid and elastic column theory, Characteristics Methods of determining pressure surges in penstocks,surge tanks

UNIT-IV

Selection of suitable type and number of turbines, Layout and spacing of turbines. Types and spacing of turbines, Tanks, And design, Power house, Types, Layout and spacing of units. Economics of Hydropower Installation- Basic factors in economic Analysis, Cost of Hydroelectric power.

Recommended Books:

Bhattacharya P K, Water Power Engineering, Khanna Publishers, 2002

Desmukh M M, Water Power Engineering, Dhanpat Rai & Sons, 2002

Brown G, Hydroelectric Engineering Practice, CPS, 1984

Fritz J J, Small and Mini Hydropower Schemes, McGraw Hill, 1984

Creager and Justin, Hydro electric Hand Book, John Wiley

Das M M, Saikia M S, Irrigation and water Power Engineering, PHI Learning Pvt. Ltd, 2009

Course Objective:

L T P Cr

3 1 - 4




CE-421/422/423/424 OPTIMIZATION TECHNIQUES FOR CIVIL ENGINEERING



UNIT-I Introduction- Introduction to optimization Techniques, Problem formulation and merit function, Linear Optimization, Simplex Algorithm duality in Linear Programming.

UNIT-II Non-Linear Optimization-(I) - Single and multiple variable optimization algorithms, Search methods, Gradient methods.

UNIT-III Non-Linear Optimization-(II) - Multi variable optimization Algorithms, Constrained and unconstrained problems, Search methods, Gradient methods, Kuhntucker conditions.

UNIT-IV

Dynamic programming Concepts- Backward recursion method, Genetic programming, Principle and concepts, Simulated ANN, Genetic Algorithms.

Computer application in optimization- Optimization software for various Civil Engineering problems.

Recommended Books:

Rao S S, Optimization theory and applications, Wiley Eastern Ltd., New Delhi, 1985

Majid K I, Optimum Design of Structures, Butter-Worth and Co. Ltd., London, 1974

Deb K, Optimization for Engineering Design, Prentice Hall of India Private Ltd., New Delhi, 1996

Ossenbruggen P J, Systems analysis for Civil Engineering, John Wiley & Sons, 1984

Course Objective:

L T P Cr

3 1 - 4




CE-421/422/423/424 BRIDGE ENGINEERING



UNIT-I

Investigation for Bridges- Investigation stages, Classification of bridges, Investigations, Estimates, Major bridges, Coverage, Topographic details, Catchments area map, Hydrologic particulars, Geotechnical details, Seismology of the area, Navigation requirements, Construction resources, Particulars of nearest bridges, Traffic forecast, Major bridges, Factors for choice of ideal site, Techno economic feasibility, Project report preparation, Preparation of drawings.

UNIT-II

Loading standards: components of bridge structure need for loading standard, Loading requirement, Railway loading standards, Road bridge loadings.

Construction of bridges: Setting out of pier and abutments, Setting out of single span bridge, Setting out of multi span bridge, Open excavation in dry condition, Foundation below water table, Pile foundations, Precast driven piles, Cast in situ piles, Load test on piles, Well foundation, Sinking of wells, Construction of super structure.

UNIT-III

Concrete Bridges for Road Transport: Design of simply supported solid slab bridge – Dispersion of load along the span, Design of slab, Design of Girder Bridge, Design of deck slabs, Design of longitudinal girders, Courbon’s method, Design of bearings Steel Bridge for Railways, Steel girder design.

UNIT-IV

Inspection of Bridges- Necessity for inspection of bridges, Inspection procedures, Aspects of inspection, Testing of bridges, Assessment of safe load bearing capacity

Maintenance of Bridges- Substructure maintenance, Super structure maintenance, Bearings, Girders.

Recommended Books:

Ponnuswamy S, Bridge Engineering, Tata McGraw Hill Publishing Company Ltd.

Aswani M G, Vazirani V N and Ratwani M M, Design of Concrete Bridges, Khanna Publishers, 2004

Course Objective:

L T P Cr

3 1 - 4




CE-421/422/423/424 HIGHWAY & AIRFIELD PAVEMENT DESIGN



Course Objective:

To equip students to design flexible and rigid pavements for highways and airfields.

UNIT-I

Types and Component parts of Pavements- Factors affecting Design and Performance of Pavements, Comparison between Highway and Airport pavements, Functions and Significance of Sub grade properties, Various Methods of Assessment of Subgrade Soil Strength for Pavement Design, Causes and Effects of variation in Moisture Content and Temperature, Depth of frost penetration

UNIT-II

Stresses in Flexible Pavements- Stresses and Deflections in Homogeneous Masses, Burmister’s 2-layer, 3-layer Theories, Wheel Load Stresses, ESWL of Multiple Wheels Repeated Loads and EWL factors, Sustained Loads and Pavement behaviour under Traffic Loads. Methods of Flexible Pavement Design- Empirical, Semi-empirical and Theoretical Approaches, Development, Principle, Design steps, Advantages and Applications of different Pavement Design Methods

UNIT-III

Stresses in Rigid pavements- Types of Stresses and Causes, Factors influencing the Stresses, General conditions in Rigid Pavement Analysis, ESWL, Wheel Load Stresses, Warping Stresses, Friction Stresses, Combined Stresses

UNIT-IV

Methods of rigid pavement design- Types of Joints in Cement Concrete Pavements and their Functions, Joint Spacings, Design of Slab Thickness, Design of Joint Details for Longitudinal Joints, Contraction Joints and Expansion Joints, IRC Method of Design.

Recommended Books:

Yoder and Witezak, Principles of pavement design, John Wiley and sons, 1975

Yang N C, Design of functional pavements, Mc Graw-Hill, 1972

Huang Y H, Pavement Analysis and Design, Pearson Publication, 2004

IRC: 37-2001, Guidelines for the Design of Flexible Pavements

IRC: 58-2002, Guidelines for the Design of Rigid Pavements

L T P Cr

3 1 - 4




CE-421/422/423/424 FINITE ELEMENT METHODS



Course Objective:

To make the back ground, Basic concepts and basic formulation of finite element method clear to the students

UNIT-I

Introduction to Finite Element Methods- Physical problems, Mathematical models and finite element solutions – Mathematical model of Discrete systems – elements and assemblage, Matrix formulation – Equations of equilibrium, Element assembly and solution for unknowns–Gauss elimination method, LDL,T Method, Basic equations of elasticity, Stress, Strain and strain, Displacement relations, Theory of stress and deformation – stress strain, Temperature relations

Review of direct stiffness method- Descretization– element and structure stiffness matrices DOF relationship, Assembly of global stiffness matrix and load vector, Solution of equations for unknowns, Displacement boundary conditions, Computation of stress, Support reactions.

UNIT-II

Continuous systems- Practical Examples–mathematical models, Differential formulation– limitations – Variational formulation – Total potential energy, Principle of stationary potential energy, Problems having many degree of freedom, Potential energy of an elastic body – the Rayleigh-Ritz method, Piecewise polynomial field, Finite element form of Rayleigh-Ritz method, Finite element formulations derived from a functional, Interpolation – shape functions for C0 and C1 elements, Lagrangian interpolation functions for two and three dimensional elements.

UNIT-III

Displacement based elements for structural mechanics- formulas for element stiffness matrix and load vector, Overview of element stiffness matrices, Consistent element nodal vector, Equilibrium and compatibility in the solution, Convergence requirements, Patch test, Stress calculation, Other formulation methods Straight sided triangles and tetrahedral: natural coordinates for lines, Triangles and tetrahedral, Interpolation fields for plane triangles, Linear and quadratic triangle– quadratic tetrahedron.

UNIT-IV

The isoparametric formulation- introduction, An isoparametric bar element, Plane bilinear element, Summary of gauss quadrature, Quadratic plane elements, Direct construction of shape functions for transition elements, Triangular isoparametric elements – consistent element nodal loads, Validity of isoparametric elements, Appropriate order of quadrature, Element and mesh instabilities, Remarks on stress computation Coordinate transformation: transformation of vectors, Transformation of stress, Strain and material properties, Transformation of stiffness matrices, Transformation of flexibility to stiffness, Inclined support, Joining dissimilar elements to one another, Rigid links– rigid elements.

Recommended Books:

Reddy J N, An Introduction to the Finite Element Method, McGraw Hill, 2006 Bathe K J, Finite Element Procedures in Engineering Analysis, Prentice Hall, 1982

Cook R D, Malkus D S, Plesha M F and Witt R J, Concepts & Applications of Finite Element Analysis, John Wiley, 2004

Yang T Y, Finite element structural analysis, Prentice-Hall, 1986 Gallaghar R H, Finite Element Analysis: Fundamentals, Prentice Hall Inc. Rajasekaran S, Finite Element Analysis in Engineering Design, Wheeler Pub, 1993

L T P Cr

3 1 - 4




CE-421/422/423/424 TRAFFIC ENGINEERING



Course Objective:

Students will deals with the planning, Geometric design and traffic operations of roads and highways for the achievement of safe, Efficient, And convenient movement of traffic. This subject will help them to solve transportation problems related to traffic.

UNIT-I

Scope of traffic engineering & study of its elements, Introduction, Objectives and scope of traffic engineering, Components of road traffic, Vehicle, Driver and road, Road user and vehicle characteristics and their effect on road traffic, Traffic maneuvers, Traffic stream characteristics, Relationship between speed, Flow and density, Sampling in traffic studies, Adequacy of sample size.

UNIT-II

Traffic engineering studies and analysis, Objectives, Methods of study, Equipments, Data collection, Analysis and interpretation (including case studies) of speed, Speed and delay, Volume, Origin and destination, Parking, Accident & other studies.

UNIT-III

Design, Regulation and management of traffic engineering facilities, Control of traffic movements through time sharing and space sharing concepts, Design of canalizing islands, T, Y, Skewed, Staggered, Roundabout, Mini-round about and other forms of at grade intersection, Crossings including provision for safe crossing of pedestrians and cyclists, Grade separated intersections, Their warrants and design features, Bus stop location and bus bay design, Road lighting, Regulations on vehicles, Drivers and traffic, Planning and design of one-way-streets, Reversible lanes and roadways, Turn regulation, Transit and carpool lanes, Pedestrian facilities.

UNIT-IV

Traffic control devices and environmental control, Traffic signs, Markings and signals, Different methods of signal design, Redesign of existing signals including case studies, Signal system and co-ordination, Air and noise pollution of different transport modes, Visual impacts, Impacts on land development, Technological approaches to improving environment.

Recommended Books:

Kadiyali L R, Traffic and Transport planning, Khanna Publishers, 1987 Pignataro L J and Cantilli E J,Traffic Engineering: Theory & Practice, John Wiley, 1973 IRC – SP41, Guidelines for the Design of At, Grade Intersections in Rural & Urban Areas O'Flaherty C A, Transport planning and traffic engineering, Arnold, 1997 Matson, Smith and Hurd, Traffic Engineering, McGraw Hill Book Co., 1955

L T P Cr

3 1 - 4




CE-421/422/423/424 ENVIRONMENTAL POLLUTION CONTROL



Course Objective:

To provide students with balanced information regarding different elements of pollution and its control measures and to make students aware of statutory controls for pollution control.

UNIT-I

Environmental pollution– interrelationship between various forms of pollution, Surface water pollution surveys, Integrated river basin water management, Restoration of water bodies, Water quality parameters and optimization of treatment, Water quality changes by domestic use, Radioactive materials, Thermal pollution and underground disposal, Types of water pollutants and their effects, Instrumentation for water quality and treatment, Role of wastewater treatment as pollution control measure.

UNIT-II

Air pollution control strategy– basic approaches, Areas of legal responsibility, Source identification, Particulate control and control of gases and vapours, Factors affecting control approach selection, Air pollution control technology, Settling chambers, Filters, Electrostatic precipitators, Wet scrubbers, Entrainment separators, Gas adsorption, Gas absorption and combustion.

UNIT-III

Land pollution– pollution cycle, Ecological factors in plant site selection, Ecological aspects of vegetation control, Noise pollution, The physics of sound and hearing, Effects of noise, Sources, Instruments and techniques for noise measurements – light and glare pollution – light and its characteristics, Glare, Outdoor lighting and glare sources, Corrective procedures.

UNIT-IV

Environmental impact analysis– physical, Social, Aesthetic and economic assessment of highway project, Mining and power plants, Legislative control, Water pollution laws and regulations, Air pollution control act of India, Chimney heights, Land pollution laws and regulations.

Recommended Books:

Rao C S, Environmental Pollution Control Engineering, New Age International (P) Ltd, 2007 Goel P K, Water Pollution Causes, Effects and Control, New age International (P) Ltd, 2006 Birdie G S and Birdie J S, Water Supply and Sanitary Engineering, Dhanpat Rai & Sons Bethea R M, Air Pollution Control technology, Van Nostrand Reinhold Co., 1978 Water Pollution Act and Air pollution act of Govt. of India Relevant Indian Standards & factory Acts

L T P Cr

3 1 - 4




CE-421/422/423/424 HYDRAULIC STRUCTURES



Course Objective:

Students will learn various method of designing different types of dams and spillways.

UNIT-I

Planning and Selection of Dams- Planning, Environmental considerations, Storage requirements, Sedimentation in reservoir, Wave height and free board, Selection of type of dam. Geological investigation, Classification of insitu, Rocks for Engineering purposes, Foundation treatment, River diversion works

UNIT-II

Gravity dams- Definition, Forces acting on the dam, Nonoverflow and overflow sections, Causes of failure design principles, Elementary profile of a dam, High and low dam, Stability analysis, Temperature control in dams, Construction and contraction joints, Galleries in dams.

UNIT-III

Arch Dam- Classification and type, Factors affecting layout, Simple design criteria – thin cylinder theory trial load analysis, Elastic theory, Cantilever and Arch analysis. Earth & Rock fill Dams: Types, Profile and design principles of earth dams, Height and top width, Side slopes and its protection, Core and casing, Cutoff and seepage control, Drainage system, Construction methods and quality control.

UNIT-IV

Spillways, Sluices and crest gates- Definition and types of spillways, Design storm and spillways capacity, Energy dissipation, Design criteria – design of crest gates and high head gates, Supply and power sluices. Instrumentation- Embedded instruments in dam section, Foundation measurements of dam body, Analysis of strain data, Automatic control of dam safety.

Recommended Books:

Sharma H D, Concrete Dams, Metroploitan, 2002 Punmia B C and Pande B, Lal B, Irrigation and Water power Engineering, Standard

Publishers, Ninth edition, 1986 Garg S K, Irrigation and Hydraulic structures, Khanna Publishers, 1992. Creager W P, Justin J D W and Hinds J, Engineering for dams. John Wiley & Sons, 1966

Das M M & Saikia M D, Irrigation and Water Power Engineering, PHI, Learning (P) Ltd, 2009

L T P Cr

3 1 - 4




CE-421/422/423/424 RETROFITTING AND REHABILITATION OF STRUCTURES



UNIT-I

Concept of Repairing- retrofitting, Strengthening, Rehabilitation, Restoration, Remoulding. Repair materials/ methods- Repair methodology, Issues related to material Technology, Desired properties of repair materials, Materials for repair, New repair systems / products. Distresses in concrete structures, Deterioration of structures, Causes and prevention, Crack repair techniques, Repair techniques/ materials for structures, Repair of structural components

UNIT-II

Retrofitting of Masonry buildings- Failure mode of masonry buildings, Out of plane failure, In-plane failure, Diaphragm failure, Failure of connection, Methods of retrofitting, Cement or epoxy injection, Using wire mesh and cement mortar, Re construction of bulged portion of masonry wall, Grouting with cement, Pointing with mortar, Shotcreting, Using FRP fabric, Using RC and steel frames, Adding reinforcements to masonry, Stitching of wall corners, Use of tie rods. Prestressing of masonry, External binding or jacketing, Splint and bandage technique, Inserting new walls, Exterior supplemental elements, Strengthening of parapets

UNIT-III

Retrofitting of RC structure- Global retrofitting methods, Adding new shear walls, Adding steel bracing, Adding infill walls, Non-conventional methods, Seismic base isolation, Supplemental damping devices. Member or local retrofit methods, Jacketing/confinements, Jacketing of columns using steel sections, Reinforced concrete jacketing, FRP jacketing, Beam jacketing, Beam column joint jacketing, Slab column connection, Foundation, Cost comparison of different method

UNIT-IV

Repair of Concrete Floors- Surface preparation, Thin bonded toppings, Reinstating joint sealants. Crack repair, Crack cleaning and resin injection, Crack cutting and mortar filling, Application of cement/sand screed, Use of toppings Retrofitting of Steel Structure- Rain water protection, Drainage in structural members, Preparation of surface by sand blasting, Protective coatings, Cathodic protection, Sacrificial metal, Adding additional plates, Strengthening the joints, Concrete jacketing

Recommended Books:

Rajoria K B, Rehabilitation and Retrofitting of Structures, Macmillan Publishers India Ltd, 2010

Agarwal P and Shrikhande M, Earthquake Resistant Design of Structures, Prentice Hall of India Pvt Ltd, New Delhi, 2006

Santhakumar A R, Concrete Technology, Oxford University Press New Delhi, 2006

Course Objective:

L T P Cr

3 1 - 4




CE-421/422/423/424 MACHINE FOUNDATIONS



UNIT-I

Introduction, Nature of dynamic loads free vibrations of spring mass systems, Forced vibrations viscous damping, Principles of vibration measuring equipments.

Dynamic properties of soils- Elastic properties of soils, Coefficient of elastic uniform and non uniform compression and shear, Effect of vibration on the dissipative properties of soils, Determination of dynamic properties of soils, Codal provisions.

UNIT-II

Analysis and design of block type machine foundations- Review of methods for dynamic analysis, Modes of vibration, Foundations for machines inducing periodical forces and impact type forces.

UNIT-III

Design of framed foundations for high speed machinery- Special consideration in planning, Principles design criteria, Structural design, Foundations for miscellaneous machines.

UNIT-IV Vibration isolation, Passive and active isolation, Use of springs and springs and damping materials, Construction aspects of machine foundations.

Recommended Books:

Saran S, Solid Dynamics and Machine Foundations, Galgotia Publications, 1999

Arora K R, Soil mechanics and foundation Engineering, SPD, 2001

Bowle’s J E, Foundation Analysis and design, 4th edition, MGL,1998

Course Objective:

L T P Cr

3 1 - 4




CE-421/422/423/424 ROCK MECHANICS



UNIT-I

Introduction- Rock Mechanics and its relationship with soil mechanics and engineering geology, Application of rock mechanics to civil engineering problems.

Classification of rocks- Lithological classification, Engineering classification of rocks, Classification based on wave velocity ratio, R.Q.D. Classification of rock masses i.e. RMR and Q systems.

UNIT-II

Rock properties- Laboratory test, Compression, Tensile, Void index, Permeability and shear, Effects of size of specimen, Rate of testing, Confining pressure etc. Stress strain curves of typical rocks, Strength of intact and fissured rocks, Effects of anisotropy, Saturation and temperature effects, Shear strength of jointed rock mass.

Field test- Uniaxial tests in tunnels and open excavations, Shear test, Pressures tunnel tests etc.

UNIT-III

Stability of rock slopes- Mode of failure of rock slopes, Plane wedge analysis, 3D wedge analysis circular mode of failure, Back analysis of slopes, Stability charts, Types and design of rock bolts.

Determination of in situ stresses- Stresses in rock, Methods of determining in situ stresses i.e hydraulic fracturing, Flat jack test and over coring.

UNIT-IV

Design of tunnels- Rock pressure theories, Ground reaction curve, Rock support interaction analysis empirical and semi empirical methods of analysis, Simple method of tunnel, Design, Types and design of tunnel lining.

Foundation of rocks- Stress distribution in foundation, Methods of determination of bearing capacity of rocks, Improvement of rock properties, Pressure grouting for tunnels and dams, Dental concreting, Shear zone treatment.

Recommended Books:

Stagg K G and Zienkiewicz O C, Rock Mechanics in Engineering Practice, John Wiley & Sons, 1979

Jaeger C, Rock Mechanics and Engineering, Cambridge University, 1979

Goodman R E, Introduction to Rock Mechanics, Wiley, 1989.

Jaeger J C, Cook N G W and Zimmerman R W, Fundamentals of rock mechanics, Blackwell Publishing, 2007

Course Objective:

L T P Cr

3 1 - 4




CE-421/422/423/424 STRUCTURAL DYNAMICS AND SEISMIC DESIGN



Course Objective:

To equip students with the basic knowledge on design of earthquake resistant structures

UNIT-I

Overview of structural dynamics – Fundamental objective of structural dynamic analysis – types of prescribed loadings, Essential characteristics of a dynamic problem, Method of discretization, Lumped mass procedure, Generalized displacements, Single degree of freedom system, Components of the basic dynamic system – formulation of the equation of motion, D Alembert’s principle, Influence of gravitational forces, Generalized SDOF system, Rigid body assemblage, Expression for generalized system properties.

UNIT-II

Solution of the equation of motion- undamped free vibration- damped free vibration, Critical damping- under damped system, Over damped system, Negative damping, And concept of Coulomb damping. Response to harmonic loading, Undamped system, Complementary solutions- particular solution, General solution, Response ratio– Viscously damped system, Resonant response dynamic amplification factor, Vibration isolation. Response to periodic loading - Fourier series expression of the loading, Response to the Fourier series loading, Exponential form of Fourier series solutions, Concept of four way logarithmic graph paper

UNIT-III

Base-excited SDOF system- formulation of basic equation, Concepts of pseudo acceleration, Velocity and displacement- Earthquake response spectra (concept only). Lumped mass modelling of multi-storey shear building and modes of vibration (concepts only-demonstration with example, Students are not expected to solve during examination) Performance of building and structures under earthquakes, Main Causes of Damage, Intensity of earth quake forces, Lack of strength and integrity of buildings, Quasi resonance, Lack of ductility, Lack of detailing. Earth quake effects- On buildings, Structures, Power plants, Switch yards, Equipments or other life line structures, Soil liquefaction, Assessment of damage Philosophy and Principles of earthquake-resistant design, Strength and stiffness, Ductility based design and detailing, Concepts of seismic isolation and seismic active control, Building forms and architectural design concepts- Horizontal and vertical eccentricities due to mass and stiffness distribution (Numerical exercises not expected) IS specifications.

UNIT-IV

Equivalent Static Method- Seismic zones and coefficients, Response reduction factors, Estimations of fundamental time period, Base shear and its distributions using IS: 1893 for multistory buildings (regular shape only). Use of codes like IS: 4326, IS: 13828, IS: 13827, IS13920, SP: 22 with reference to masonry, RCC and steel building Detailing of reinforcement and joints. Restoration and retrofitting, Methodologies for restoration and retrofitting, For walls, Roofs, Slabs, Columns and foundation of building in stones, Brick or reinforced concrete structures

Recommended Books:

Chopra A K, Dynamics of structures-theory and applications to earthquake engineering, Pearson Education, 2007

Clough R W and Penzien J, Dynamics of structures, McGraw Hill, 1975

JaiKrishna and Chandrasekaran A R, Elements of earthquake engineering, Saritha Prakasan, Meerut, 1976

L T P Cr

3 1 - 4




OE-431/432 OPERATIONS MANAGEMENT



Course Objective:

The objective of the paper is to facilitate the student with the basics of Operation Research used in communication. The scope of the subject is to acquire skills to apply the stochastic processes in engineering problems and solve the mathematical problem.

UNIT-I

Development of OR, Definition of OR, OR Characteristics and Phases, Types of models, Operation Research models and OR applications, Introduction To Linear Programming (LP), Introduction to applications of operations research in functional areas of management, Linear Programming- formulation, Solution by graphical and simplex methods (Primal – Penalty, Two Phase), Special cases. Dual simplex method, Principles of Duality, Sensitivity Analysis, Linear programming formulation and graphic solution, Models of mathematical operations research, Art of modeling, Construction of the LP model, Graphical LP solution.

UNIT-II

Sets, Probability, Conditional Probability, Bernoulli Trials, Asymptotic Theorems, Poisson Theorem, Random Variables, Distribution and Density Functions, Conditional and Total Probability, Mean, Variance, Moments, Cumulants, Characteristic Functions, Bivariate and Multivariate Random Variables, Joint Moments, Joint Characteristic Functions, Conditional Distributions, Conditional Expected Values, Sequences of Random variables, Mean Square Estimation, Stochastic Convergence and Limit Theorems, Random Numbers, Meaning and Generation, Parameter Estimation, Hypothesis Testing.

UNIT-III

Graphical solution, Artificial variables techniques, The Simplex method Standard LP form, Basic solution, The Simplex method, The M-method, The two-phase method, Degeneracy, Alternative optimal solution, Unbounded solution, Infeasible solution, Sensitivity analysis and dual problem Definition of the dual problem, The relationship between the optimal primal and dual solution, Economic interpretation of duality, The dual Simplex method, Primal-dual computations, Sensitivity analysis, Duality Principle, Transportation Problem, Introduction - mathematics model – types – methods transshipment model, Modeling of quantity discounts., SEQUENCING – Introduction – Flow –Shop sequencing – n jobs through two machines – n jobs through, Three machines – Job shop sequencing – two jobs through ‘m’ machines.

UNIT-IV

Dynamic Programming, Introduction – Bellman’s Principle of optimality – Applications of dynamic programming- capital budgeting problem – shortest path problem – linear programming problem, Simulation, Definition – Types of simulation models – phases of simulation– applications of simulation, Inventory and Queuing problems – Advantages and Disadvantages – Simulation Languages, Network models Network definition, Minimal spanning tree algorithm, Shortest route problem, Shortest route algorithm, Maximal flow model, Enumeration of cuts, Maximal flow algorithm, CPM, PERT.

Recommended Books:

Sharma S D, Kedarnath, Operations Research Hiller & Libermann, Introduction to O.R, (TMH) Popoulis and Pillai S V, Probability, Random Variables and Stochastic Processes, TMH, 2002 Natarajan A M, Balasubramani P, Tamilarasi A, Operations Research, Pearson Education Saseini Maurice, Yaspan Arhur & Friedman Lawrence, Operations Research Methods &

Problems Pannerselvam R, Operations Research, PHI Publications

L T P Cr

3 - - 3



Taha Hamdy, Operations Research – An Introduction, 7th edition PHI (2003) Philipose Susy, Operations Research, TMH New Delhi Sharma S D, Operation Research, Kedarnath and Rannalt Pub Hira and Gupta, Operation Research, S. Chand and Co




OE-431/432 ADVANCED ENGINEERING MATHEMATICS



Course Objective:

The aim of the syllabus is to study the convergence behavior of various infinite series, To solve the applications based on double integral (surface integral) and triple integral (volume integral). The last unit ‘functions of complex variables’ has been added due to its usefulness in evaluating large number of new definite integrals, The theory of differential equations, The study of electric fields, Thermodynamics, And fluid mechanics.

UNIT-I

Convergence and divergence, Comparison tests, D'Alembert's ratio test, Integral test, Raabe's test, Logarithmic and Cauchy root tests, Gauss's test.

Alternating series, Absolute convergence, Conditional convergence and Uniform Convergence.

UNIT-II

Differentiation of vectors, Scalar and vector point functions Gradient of a scalar field and directional derivative, Divergence and curl of a vector field and their physical interpretations, Del applied twice to point functions, Del applied to product of point functions.

Integration of vectors, Line integral, Surface integral, Volume integral, Green’s, Stoke’s and Gauss divergence theorems (without proof), And their simple applications.

UNIT-III

Double integral, Change of order of integration Double integral in polar coordinates, Applications of double integral to find area enclosed by plane curves and volume of solids of revolution.

Triple integral, Volume of solids, Change of variables, Beta and gamma functions and relationship between them.

UNIT-IV

Functions of a complex variable, Exponential function, Trigonometric, Hyperbolic and Logarithmic functions, Limit and continuity of a function, Differentiability and analyticity.

Cauchy-Riemann equations, Necessary and sufficient conditions for a function to be analytic, Polar form of the Cauchy-Riemann equations, Harmonic functions, Application to flow problems, Conformal transformation, Standard transformations (Translation, Magnification & rotation, Inversion & reflection, Bilinear).

Recommended Books:

Kreyszig F, Advanced Engineering Mathematics Grewal B S, Higher Engineering Mathematics Sastry S S, Engineering Mathematics Part-I Piskunov, Differential and Integral Calculus Jain R K and Iyengar S R K, Advanced Engineering Mathematics

Greenberg Michael D, Advanced Engg. Mathematics

L T P Cr

3 - - 3




OE-431/432 ENTREPRENEURSHIP



UNIT-I

Concept of Entrepreneurship, Development Evolution of the concept of an Entrepreneur, Entrepreneur Vs. Intrapreneur, Entrepreneur Vs. Entrepreneurship, Attributes and characteristics of a successful Entrepreneur, Role of Entrepreneur in India economy and developing economics with reference to self-Employment, Entrepreneurship Culture.

Definition and types of Small scale industries, Role, Scope and performance in national economy, Problems of small scale industries, Industrial Sickness, Causes of sickness, Indian scenario, Government help, Management strategies, Need for trained entrepreneurs

UNIT-II

Engineering Economics, Importance of economics for engineers, Present value and future value, Wealth, Goods, Wants, Value and price, Capital, Money, Utility of consumer and producer goods, Cost, Elements of cost, Prime cost, Overhead, Factory cost, Total cost, Selling price, Nature of cost, Types of cost, Depreciation, Causes of depreciation, Methods of calculating depreciation, Economic analysis of investment and selection of alternatives, Nature of selection problem, Nature of replacement problem, Methods used in selection of investment and replacement alternatives. Tools for evaluation of techno economic feasibility project report, SWOT analysis.

UNIT-III

Creating Entrepreneurial Venture, Business Planning Process, Environmental Analysis – Search and Scanning, Identifying problems and opportunities, Defining Business Idea, Basic Government Procedures to be complied with, Role of Central Government and State Government in promoting Entrepreneurship – Introduction to various incentives, Subsidies and grants – Export Oriented Units – Fiscal and Tax concessions, District Industries Centers (DIC), Small Industries Service Institute (SISI), Entrepreneurship Development Institute of India (EDII), National Institute of Entrepreneurship & Small Business Development (NIESBUD), National Entrepreneurship Development Board (NEDB) The FOUR Entrepreneurial Pitfalls (Peter Drucker)

UNIT-IV

Business Incubation, Origin and development of business incubators in India and other countries, Types of incubators, Success parameters for a business incubator, Benefits to industries, Institutes, Government and Society, Future prospects.

Special Aspects of Entrepreneurship, Social entrepreneurship, International entrepreneurship, Rural entrepreneurship, Community Development, Women entrepreneurship.

Recommended Books:

Gupta P K, Strategic Entrepreneurship, Everest Publishing House Meredikh G G, Nelson RE, And Neck PA, The practice of Entrepreneurship Tarachand, Engineering Economics A Hand Book for New Entrepreneurs by EDI, Ahemdabad Hisrich Peters Entrepreneurship (Tata Mc Graw) Williamsons, Cost and Management Accounting, Prentice Hall of India Holl H David, Entrepreneurship-New Venture Creation, Prentice Hall of India Vasant De, Dynamics of Entrepreneurship Development Rao and Pareek, Handbook of Entrepreneurship

Course Objective:

L T P Cr

3 - - 3




OE-431/432 SOFT COMPUTING



Course Objective:

The objective is to facilitate the student with the basics of soft computing and its application. The scope of the subject is to acquire skills to apply the neural network and ANN process.

UNIT-I

Neural Networks, History, Overview of biological Neuro-system, Mathematical Models of Neurons, Artificial neural networks, Basic concepts, Single layer perception, Multilayer Perception Supervised and Unsupervised learning, Back propagation networks, Kohnen's self organizing networks, Hopfield network, Applications of Artificial Neural Networks, Comparison of Soft Computing Methods.

UNIT-II

Overview of to Fuzzy Logic, Set Theoretic Operators, Membership functions, Operations on Fuzzy Sets, Fuzzy Arithmetic, Fuzzy Logic Uncertainty based Information: Information & Uncertainty, Nonspecificity of Fuzzy & Crisp Sets, Fuzziness of Fuzzy Sets.

UNIT-III

Fuzzy Rules and Fuzzy Reasoning, Fuzzy Inference Systems- Mamdani and Sugeno Fuzzy models, Fuzzy Assocaitive Memories, Basics of Genetic Algorithms, Design issues in Genetic Algorithm, Survival of the Fittest, Fitness Computations, Cross over, Mutation, Reproduction, Rank method, Rank space method, GA in problem solving, Implementation of GA, Swarm Intelligence, Ant Colony system, PSO system, GA based Fuzzy Model Identification, Fuzzy Logic controlled Genetic Algorithm.

UNIT-IV

Introduction of Neuro-Fuzzy Systems Architecture of Neuro Fuzzy Networks, Neuro – fuzzy modeling, Adaptive networks based Fuzzy interface systems, Classification and Regression Trees, Data clustering algorithms, Rule based structure identification, Neuro-Fuzzy controls, Simulated annealing, Evolutionary computation, Neuro- Genetic Hybrids & Fuzzy, Genetic Hybrids, Application of Fuzzy Logic, Medicine, Economics etc.

Applications of soft computing, Optimization of traveling salesman problem using Genetic Algorithm, Genetic algorithm based Internet Search Techniques, Soft computing based hybrid fuzzy controller, Introduction to MATLAB Environment for Soft computing Techniques.

Recommended Books:

Anderson J A, An Introduction to Neural Networks, PHI Sivanandam, Deepa, Principles of Soft Computing, Wiley

Krogh Hertz J, Palmer R G, Introduction to the Theory of Neural Computation, Addison- Wesley

Klir G J & B. Yuan,Fuzzy Sets & Fuzzy Logic, PHI Melanie Mitchell, An Introduction to Genetic Algorithm, PHI

Rajasekharan S, Vijayalekshmi Pai S A, Neural Networks, Fuzzy Logic & Genetic Algorithms, PHI 2003

Jang J S R, Sun C T, E Mizutani, Neurofuzzy and Soft Computing, PHI Goldberg David E, Genetic Algorithms, Pearson Yen John & Langari Reza, Fuzzy Logic, Intelligence, Control, And Information, Pearson. Lin C T & Lee C S G, Neural Fuzzy Systems, PHI

L T P Cr

3 - - 3




OE-431/432 ARTIFICIAL INTELLIGENCE



Course Objective:

To make the students understand the basic concepts of AI. After undergoing this course the students will have the knowledge of issues in AI, Programming, Knowledge representation, Approximate reasoning, Planning and learning etc.

UNIT-I

Fundamental Issues In Artificial Intelligence, Foundation and history of AI, AI problems and techniques, AI programming languages, Introduction to LISP and PROLOG, Problem spaces and searches, Blind search strategies, Breadth first- Depth first - heuristic search techniques, Hill climbing, Best first - A* algorithm, AO* algorithm- game tree, Min max algorithms, Game playing- alpha beta pruning.

UNIT-II

Knowledge Representation, Issues, Predicate logic, Logic programming, Semantic nets, Frames and inheritance, Constraint propagation, Representing knowledge using rules, Rules based deduction systems.

UNIT-III

Approximate Reasoning, Reasoning under uncertainty, Review of probability, Baye’s probabilistic inferences and Dempster Shafer theory, Heuristic methods, Symbolic reasoning under uncertainty, Statistical reasoning, Fuzzy reasoning, Temporal reasoning, Non-monotonic reasoning.

UNIT-IV

Planning in situational calculus, Representation for planning, Partial order planning algorithm, Learning from examples, Discovery as learning, Learning by analogy, Explanation based learning, Introductory remarks on learning by Neural Networks and Genetic Algorithms. Applications: Rule based systems architecture, Expert systems, Knowledge acquisition concepts, AI application to robotics, And current trends in intelligent systems.

Recommended Books:

Russell & Norvig., Artificial Intelligence: A Modern Approach, Prentice Hall, 1995

Elain Rich and Kevin Knight, Artificial Intelligence, TMH, 1991

Staurt Russel and Peter Norvig, Artificial Intelligence – A modern approach, PHI, 1998

Patrick Henry Winston, Artificial intelligence, 3rd Ed., Addition Wesley, 1992 Patterson Dan W, Artificial Intelligenc”, PHI, 1990

L T P Cr

3 - - 3




OE-431/432 REMOTE SENSING & GIS Internal Evaluation: 25 Marks


Course Objective:

To make the students understand the knowledge about to forecast the quantity of materials required for each item of work from the available drawings. The student should also know about specifications of each work, knowledge of earthwork calculation and preparing of abstract of cost. A diploma holder in civil engineering has a major job of valuation and rent fixation. Once he is working as junior engineer or contractor he must be familiar with the departmental procedures. The student will get the knowledge of making tender notices, inviting tenders, executing contracts and recording M.B.

UNIT-I

Photogrammetry: Definition of Photogrammetric Terms, Geometry of aerial and terrestrial photographs, Aerial camera and photo-theodolite, Scale of a Photograph, Tilt and Height displacements, Stereoscopic vision and stereoscopes, Height determination from parallax measurements, Flight planning, Maps and Map substitutes and their uses.

UNIT-II

Remote Sensing: Introduction and definition of remote sensing terms, Remote Sensing System, Electromagnetic radiation and spectrum, Spectral signature, Atmospheric windows. Different types of platforms, sensors and their characteristics, Orbital parameters of a satellite, Multi concept in Remote Sensing.

UNIT-III

Image Interpretation: Principles of interpretation of aerial and satellite images, equipments and aids required for interpretation, ground truth – collection and verification, advantages of multidate and multiband images. Digital Image Processing concept.

UNIT-IV

Geographic Information System (GIS) : Introduction & applications of GIS in map revision, Land use, Agriculture, Forestry, Archaeology, Municipal, Geology, water resources, Soil Erosion, Land suitability analysis, change detection.

REFERENCE BOOKS: 1. Basics of Remote Sensing & GIS by Dr. S.Kumar , Univertsity Sc. Press.

L T P Cr

3 - - 3




OE-431/432 RENEWABLE ENERGY SOURCES



Course Objective:

To make the students aware about the various renewable and non conventional resources of energy available, Their potential and utilization. The students learn how to meet the growing energy needs by the use of environmental friendly renewable energy resources.

UNIT-I

Introduction to non-conventional/renewable energy sources, Importance of these sources for sustainable development and environmental protection

Solar radiations, Measurement of solar radiation, Characteristics of solar spectra including wavelength distribution, Radiation properties and spectral characteristics of materials, Selective surfaces and basics of solar collectors, Solar collection devices and their analysis, Solar collector characteristics; Solar pond, Application of solar energy to space heating etc.

UNIT-II

Biomass as an energy Source, Energy plantations, Conversion technologies – thermal, Chemical and biological, Photosynthesis, Biogas generation, Classification of biogas plants.

Principles of Bioconversion, Types of bioreactors, Reaction kinetics, Reactor design and analysis, Materials-Municipal refuse, Sewerage, Industrial wastes, Agricultural wastes, Animal and human wastes; Landfill systems, Properties and uses of biogas.

Bioconversion techniques, Utilization of industrial wastes such as bagasse, Household and community combustion systems, Gasification, Sizing, Beneficiation of fuels, Thermodynamics and kinetics of gasification, Types of gasifiers, Combustion characteristics of bio fuels, Utilization in conventional engines and or power generation including cogeneration.

UNIT-III

Waves, Nature and availability of energy from waves onshore and off-shores, Principles of wave converters, Energy conversion and transmission.

Origin and nature of tides, Tidal heads and duration, Principles of tidal energy conversion, Site Selection, Cycles and load factors, Regulation and control of tidal power generation.

Ocean thermal energy conversion (OTEC), Temperate and tropical oceans; Principles of OTEC systems; Site selection, Power cycles, Selection of working fluids, Pumps and turbines, Heat exchanger criteria, Power transmission and system efficiency.

UNIT-IV

Introduction to wind energy, Basic components of a wind energy conversion system (WECS), Classification of WECS, Applications of Wind Energy, Environmental aspects, Wind Energy Developments in India.

Geothermal resources, Location and potential assessment, Classification and characteristics of geothermal resources, Chemical and physical properties of geothermal brines, Control of scale deposition, Drilling, Logging and cementing operations for geothermal wells; Principles of power production system and cycles, Thermal Utilization and mineral recovery, Ecological and safety considerations.

Recommended Books:

Sukhatme S P, Solar Energy: Principles of Thermal Collection and Storage, TMH

Garg and Prakash, Solar Energy: Fundamentals and Applications, Tata McGraw Hill Chang, Energy Conversion, Prentice Hall Soo, Direct Energy Conversion, Prentice Hall Duffic and Beckman, Solar Engineering of Thermal Processes, John Wiley

L T P Cr

3 - - 3




OE-431/432 CONSUMER ELECTRONICS



Course Objective:

To make the students understand the basic concepts of modern consumer electronics products. After undergoing this course the students will have the knowledge and technical understanding of various electronic products needed in day to day activities.

UNIT-I

Loudspeakers and Microphones: Dynamic Loudspeaker, Electrostatic loudspeaker, Permanent Magnet Loudspeaker, Woofers and Tweeters - Microphone Characteristics, Carbon Microphones, Dynamic Microphones and Wireless Microphones.

UNIT-II

Television Standards and systems: Components of a TV system – interlacing – composite video signal. Colour TV – Luminance and Chrominance signal; Monochrome and Colour Picture Tubes - Colour TV systems – NTSC, PAL, SECAM - Components of a Remote Control.

UNIT-III

Optical Recording and Reproduction: Audio Disc – Processing of the Audio signal – read out from the Disc – Reconstruction of the audio signal – Video Disc – Video disc formats- recording systems – Playback Systems.

UNIT-IV

Telecommunication Systems: Telephone services - telephone networks – switching system principles – PAPX switching – Circuit, Packet and message switching, LAN, MAN and WAN, Integrated Services Digital Network. Wireless Local Loop. VHF/UHF radio systems, Limited range Cordless Phones; cellular modems, Home Appliances: Basic principle and block diagram of microwave oven; washing machine hardware and software; components of air conditioning and refrigeration systems.

Recommended Books:

Bali S P, Consumer Electronics, Pearson Education, 2005

Hoff Philip, Hoff Philip Herbert, Consumer electronics for engineers, Cambridge University Press, 1998

Davidson Homer L, Troubleshooting & Repairing Consumer Electronics Without a Schematic, McGraw Hill, 2004

L T P Cr

3 - - 3




OE-431/432 SECURITY IN COMPUTING



Course Objective:

To expose students to the concepts and issues of security in computing. The objective of the course is to facilitate the student with the concepts of elementary cryptography, Mathematical background of cryptography, Security issues in networks.

UNIT-I

Introduction to elementary cryptography, Substitution ciphers, Transpositions, DES, AES encryption standard, Public key encryption, Uses of encryption, Secure programs, Non malicious program errors, Virus and other malicious code, Targeted malicious code, Controls against program threats.

UNIT-II

Protection in general purpose operating systems, Designing trusted operating systems, Security policies, Models of security, Trusted operating system design, Data base security, Introduction to database security, Security requirements, Reliability and integrity, Sensitive data, Inference, Multilevel data bases,

UNIT-III

Security in networks, Network concepts, Threats in network, Network security controls, Firewalls, Intrusion detection systems, Secure email, Introduction to administering security, Legal, Privacy and ethical issues in computer security, Information and law, Software failures, Computer crime.

UNIT-IV

Cryptography mathematics, Symmetric encryption, Public key encryption systems, Characteristics, Merkle hellman knapsacks, Rivest Shamir Adelman encryption el gamal and digital algorithms, Quantum cryptography, Quantum physics, Photon reception, Cryptography with photons .

Recommended Books:

Charles p. pfleeger, Shari Lawrence pfleeger, Security in computing,3rd edition, Pearson education.

L T P Cr

3 - - 3




OE-431/432 MODELING AND SIMULATION



UNIT-I

Nature of simulation, Advantages and disadvantages, Areas of application, System and system environment, Component of a system, Discrete and continuous system, Types of model, Steps in a simulation study, Simulation examples.

Concepts in discrete-event simulation, Event-scheduling/time advance algorithm, Manual simulation using event scheduling, Simulation softwares, Classification, Desirable software features and General purpose simulation packages.

UNIT-II

Statistical Models In Simulation, Terminology, Useful statistical models, Discrete distributions, Continuous distributions, Poisson’s process.

Properties of random numbers, Generation of Pseudo-random numbers, Techniques of generating random numbers, Inverse transform technique, Acceptance-rejection technique, Direct transformation of generating random numbers.

UNIT-III

Modeling, Verification and Validation, Data collection, Identifying the distribution with data: histograms, Selecting the family of distributions, Parameter estimation, Selecting input models without data, Model building, Verification of simulation models, Calibration and validation of models.

UNIT-IV

Output Analysis, Types of simulation with respect to output analysis, Stochastic nature of output data, Measures of performance and their estimation, Output analysis for terminating simulation and steady state simulation, Case studies of simulation of manufacturing systems.

Recommended Books:

Law Averal M and Kelton W David, Simulation Modeling and Analysis, McGraw Hill Banks J, Carson J S & Nelson B L, Discrete-Event System Simulation, Prentice Hall Zeigler B P, Kim Taq gon and Praehofer Herbert, Theory of Modeling & Simulation,

Academic Press Banks Jerry, Handbook of Simulation: Principles, Methodology, Advances, Applications &

Practice Khoshnevis, Discrete Systems Simulation

Course Objective:

L T P Cr

3 - - 3




OE-431/432 MICROPROCESSORS AND MICROCONTROLLERS



Course Objective:

To make the students understand the basic concepts of microprocessors and popular microcontrollers. After undergoing this course the students will have the technical understanding of various electronic controllers embedded in numerous real time systems for precise control and monitoring of various events.

UNIT-I

8085 Microprocessor: Evolution of Microprocessors, 8085 architecture, Timing and Control signals, Registers, Address and data busses, Instruction format, Addressing modes, Instruction set, Assembly Language Programming, Stacks and Subroutines, Memory and I/O interfacing. Introduction to 8086 Hardware Architecture and features.

UNIT-II

8051 Microcontrollers, Microcontrollers Vs Microprocessors, 8051 Architecture, Instruction set, 8051 Assembly Language programming, Counters and Timers, Serial I/O, Interrupts.

PIC Microcontroller, Overview of PIC microcontroller, Instruction set, Timer compare and capture mode, Watch dog Timer, Synchronous Serial Port, Serial Peripheral Interface, I2C Bus operation

UNIT-III

Peripheral interfacing, Programmable Peripheral interface 8255, Keyboard and display interface 8279– Programmable timer 8253, USART 8251,

Programmable Interrupt controller 8259. ADCs, DACs.

UNIT-IV

Microcontroller based Systems Design, LCD interfacing, Sensor interfacing, Real time clock, Relay, PWM, DC and Stepper motor interfacing. Case Studies: Data Acquisition System, Temperature monitoring system, Manipulator Robot Arm.

L T P Cr

3 - - 3




OE-431/432 CIVIL ENGINEERING ESTIMATING & COSTING Internal Evaluation: 25 Marks


Course Objective:

To make the students understand the knowledge about to forecast the quantity of materials required for each item of work from the available drawings. The student should also know about specifications of each work, knowledge of earthwork calculation and preparing of abstract of cost. A diploma holder in civil engineering has a major job of valuation and rent fixation. Once he is working as junior engineer or contractor he must be familiar with the departmental procedures. The student will get the knowledge of making tender notices, inviting tenders, executing contracts and recording M.B.

UNIT-I

Introduction :Purpose, Importance of estimating, Common items of works in civil engineering construction works, Units of measurement for common items of works, Methods of measurement Explanation of common terms used for estimating, Different types of estimates and their significance, Merits and demerits. Methods of taking out quantities, Study of Basic Schedule of Rates (B.S.R.),Rate>Analysis :Factors affecting cost of work, Explanation of terms, Prime cost Original cost, Provisional items, Provisional sum, Day work, item wise, Analysis of cost of material, Labor, Transport, Establishment charges and incidentals, Preparation of analysis of rates for items of work involved in building construction mentioned in practical, syllabus. Specifications: Importance of specifications. Principles for writing out specifications, types of specification, Writing general and detailed specifications for items of work in building construction mentioned in, practical syllabus.

UNIT-II

Detailed Estimates for Buildings: Calculation of quantities, Preparing abstract of cost for a residential building. Earth Work

Calculations for Road & Rail Formation: Earthwork calculations and estimates for roads and rail formation, For earth work following methods may be used: Mean depth method. Mean area method. Prismoidal formula method, Graphical method, Using longitudinal and typical cross sections, Cross section for different stations. Finding earth work by these sections, Calculation of permanent and temporary lands for roads, Economical depth of digging for canals, Mass haul diagram

UNIT-III

Preparing Detailed Estimates for the Various Items of Work from the given Drawing for

Detailed estimates for earthwork of irrigation canals, Septic tank and soak pit, Bitumen road, Valuation of

Property and Rent Fixation :Objects of valuation, Free-hold property, Lease-hold property, Property income .Obsolescence, Market-value, Book value, Distress value, Monopoly, value, Salvage value, Scrap value, Accommodation value, Replacement value, Sentimental value, Speculative value, Factors affecting the value of the property, Annuity, Capital cost, Capitalized value, Year’s purchase, Methods of determining depreciation, Valuation of property, Method of determining valuation of property, Typical valuation report, Types of rents, Rules of capital cost fixation for govt. buildings, Rules for calculation of standard rent.

UNIT-IV

Procedure of Works :Main staff structure of engineering department Duties of junior engineer Administrative approval, Expenditure sanction or approval, Technical sanction or a approval, Tender System, E-tendering, Technical bid and financial bid, Appropriation and re-appropriation of funds, Procedure for original minor and major works, Repair works, Types of estimates, Preliminary estimate, Cubical content estimate, Plinth area estimate, Revised estimate, Supplementary estimate, Daily labour on muster roll system, Completion report, Stores, Tools and Plants

:Purchase of stores, Reserve of stock, Dead stock, Surplus and unserviceable stores, Verification of stores, Issue of materials from stock, Tools and plants, M.A.S. account.

REFERENCE BOOKS: 1. Estimating & Costing Chakerborty 5. Estimating & Costing Vazirani & Chandola 2. Estimating & Costing B.N. Dutta 6. Civil Engg. Estimating & Costing Mahajan 3. Estimating & Costing Rangwala 7. Civil Engg. Estimating & Costing G.S. Birdie 4. Estimating & Costing Bhasin 8. P.W.D. Basic Schedule of Rates of Rajasthan State

L T P Cr

3 - - 3




CE-441/442 INDUSTRIAL TRAINING/PROJECT


INDUSTRIAL

TRAINING/

PROJECT

Each student is expected to undergo one complete semester of industrial/field/Lab training in order to connect the class room teaching with real time practical applications. A supervisor (faculty from the Department) shall be assigned to the student approved by the competent authority. The training and placement officer (TPO) will facilitate the students for the purpose with the consent of his/her supervisor and also considering the interests of the student. During training the student will undertake a project involving design/experimental/analytical/computational work including case studies etc. The progress of the project work will be evaluated by the concerned supervisor and TPO by visiting the site/industry/lab etc.

The student will complete the training/project by the end of the semester and a comprehensive training/project report will be submitted by the student under the signature of his/her supervisor. The external examination shall be taken by a panel of examiners comprising of concerned supervisor, the training and placement officer and an external examiner (from the relevant field) nominated / approved by the competent authority. Hard copies of report are required to be submitted by the student before the external examination. The candidate shall appear before the evaluation committee for oral examination and presentation on the scheduled date.

L T P Cr

- - 40 20



B TECH (8th SEMESTER) CIVIL ENGINEERING CE-450 COMPREHENSIVE ACADEMIC AND GENERAL PROFICIENCY

(VIVA-VOCE)

External Examination: 50 Marks

COMPREHENSIVE ACADEMIC AND

GENERAL PROFICIENCY

A viva–voce for every student for his/her academic and General Proficiency for the Profession shall be carried out by a committee comprising of three members including Principal/Director, Head of Department, and an External Examiner appointed by University. The evaluation will be made in the light of various parameters including Academic Performance, Extra Curricular Activities, Educational tours / visits / Membership of Professional Societies, Contribution in NSS Social Welfare Floor Relief / draught relief / Adult Literacy mission / Literacy Mission / Blood Donation / any other Social Service, other achievements in the Institution and the performance in Viva voce before the committee.

L T P Cr

- - - 2

Documents

Mewar University Chittorgarh (Rajasthan) Civil Syllabus.pdf · BS-103 Engineering Mathematics-I 3 1 - 4.0 35 15 50 100 BS-105 Engineering Chemistry 3 1 - 4.0 35 15 50 100 ES-101 Engineering