Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
MEDICAL RANGE
INTRODUCTION
The following catalogue contains a range of luminaires suitable for use in medical facilities or applications where a clean environment is required.
© Eagle Lighting Australia 2013 All rights reserved.
DISCLAIMER:
Whilst every effort has been made to ensure the accuracy of the information in this publication, ELA assumes no responsibility for errors, omissions or typographical errors.
All goods supplied by Eagle Lighting Australia are subject to our general terms and conditions.
For further information on any of the products featured in this catalogue, please contact your local Sales Representative.
CONTENTS
Caring Environments 05Patient Consideration 06Florence Elite 07Visible Improvements 08Welcoming Environment 09Gondol 10Cleanroom IP44 11Cleanroom IP54 12Cleanroom CLB 13Secureroom 14Secureroom SLB 15Operating Theatre Light 16Aureled Vista 18
NO OTHER PHYSICAL SITUATION CREATES SUCH UNIQUE LIGHTING DEMANDS AS A HOSPITAL BUILDING. PATIENT COMFORT AND WELL-BEING REQUIRE PRIMARY CONSIDERATION, ALONGSIDE PROVISION OF A GOOD WORKING ENVIRONMENT FOR STAFF, WHILE ENERGY CONSERVATION AND LIFECYCLE COSTS ARE ALSO OF MAJOR IMPORTANCE.
PATIENT WELL BEING
Research confirms the direct link between light quality and patient recovery rates. Recent studies show that an improved ward environment results in a reduction in non-operative patient recovery times of 21%.
With the average cost of in-patient care running at $1307 per day, this represents a significant annual saving. From an operational point of view, there are clear consequential benefits in terms of shorter bed occupancy, faster patient turn-round and improved efficiency.
WORKING ENVIRONMENT
Hospital staff need good lighting to perform daily duties effectively, especially with the flexibility that different work areas demand. Lighting also influences comfort and stress levels, and improvements in these contribute to reduced absences and increased productivity.
ENERGY SAVINGS
The potential for wasted energy in hospitals is higher than in most buildings, with many areas working on a 24/7 basis. Good lighting design and installation will deliver major longterm energy savings, with corresponding cost benefits.
Days inHospital
ModernHospital
2000+
OlderPost/Pre-War
Hospital
1 2 3 4 5 6 7
4.5
Day
s
6.85
Day
s
LIFECYCLE COSTS AND THE 1:5:200* RULE
For a typical hospital building, lifecycle costing indicates that for every $1 spent on construction, $5 is required for facilities management and no less than $200 in costs associated with the people who use it. Lighting is a significant factor in this equation, and choosing the right system and equipment can make a dramatic difference to long-term project viability.
RELATIVE EXPENDITURE
HEALTHCARE LIGHTING EXPERTS
To meet all these special requirements requires a special kind of lighting service, based on a deep understanding of the needs of patients, staff and visitors, and a sound grasp of the practicalities of building design and construction.
With extensive experience of lighting hospitals, exceptional lighting design expertise and the ability to provide innovative solutions for every different internal environment, Eagle Lighting Australia is perfectly placed to meet those needs.
* Source - The Long-Term Cost of Owning and Using Buildings Evans, Harigott, Haste and Jones, Royal Academy of Engineering, November 1998.
STAFF EXPENDITURE FACILITIES MANAGEMENT CONSTRUCTION COSTS
$200 $1$5
CARING ENVIRONMENTSNo other physical situation creates such unique lighting demands as a hospital building.
Modern Hospital
2000+
OlderPost/pre-War
Hospital
KEEPING CONTROL
To cater for varying patient needs and staff activities, wards need to operate in six different lighting modes : resting, reading, examination, night-time, watchlight and emergency.
PATIENT COMFORT
Patient comfort is optimised by eliminating glare and providing soft ambient lighting. Patient control integrated into a nurse call hand set enables patients to modify lighting levels. At the same time, central control allows staff to reset levels for a whole room at the touch of a switch.
With low positioning and ease of access, the lighting units can also be more easily maintained and cleaned, helping to improve efficiency and control infection.
PATIENT CONSIDERATIONSimple, easy control of lighting levels in wards and nursing stations
FLORENCE ELITE Low profile IP40 direct/indirect bedhead luminaire.
4
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C
FLORENCE ELITE
EL-FEL3921 1 x 39W UP/1 X 21W DOWN T5 895 213 95
EL-FEY2415LED 2400 LUMENS UP/1500 LUMENS DOWN (DALI)
895 213 95
TECHNICAL INFORMATION
Optics
Light source options: + LED 2400 lumens 26W* uplight (ward lighting)
+ LED 1500 lumens 20W* downlight (reading/nursing care)
OR + 1 x 39W (44W)* T5 uplight (ward lighting)
+ 1 x 21W (25W)* T5 downlight (reading/nursing care)
*Total power consumption including driver/ballast
Uplight – wide integrated reflectors to maximse efficiency
Downlight – Nano prism diffuser for maximum patient comfort
Medium power LEDs deliver 50,000hrs life to L70
Both the ward and reading light sources are independently dimmable by “push control” so the following lighting levels can be selected to meet the following requirements:
Patient rest 30-50 Lux
Watch light 15-20 Lux
Reading 300 Lux
General nursing care 300 Lux
LED version requires DALI controls and onsite commissioning
Body
IP40
Extruded aluminium spine & ‘push on’ moulded end caps
One piece membrane diffuser for maximum infection control
Wall mounted, recommended mounting height 2m for typical 2.6m-3m ceiling heights
1st fix wall bracket, pre-wired to GST 18/4 flying leads
No visible screws
OPTIONS
+ Seismic Restraint
N18226
C A
B
DIME NS IONS
L W H KG
895 213 95 5.0
FLO
REN
CE
ELIT
E
florence elite low profile IP40 direct/indirect bedhead luminaire
Optics• Light source options:
– LED 2400 lumens 26W* uplight (ward lighting) – LED 1500 lumens 20W* downlight (reading/nursing care)
Or
– 1 x 39W (44W)* T5 uplight (ward lighting) – 1 x 21W (25W)* T5 downlight (reading/nursing care)
*Total power consumption including driver/ballast
• Uplight – wide integrated to maximse
• Downlight – Nano prism di�user for maximum patient comfort
• Medium power LEDs deliver 50,000hrs life to L70• Both the ward and reading light sources are independently
dimmable by “push control” so the following lighting levels can be selected to meet LG2 requirements: – Patient rest 30-50 Lux – Watch light 15-20 Lux – Reading 300 Lux – General nursing care 300 Lux
• LED version requires DALI controls and onsite commissioning
Body• IP40
• Extruded aluminium spine & ‘push on’ moulded end caps
• One piece membrane di�user for maximum infection control
• Wall mounted, recommended mounting height 2m for typical 2.6m-3m ceiling heights
• 1st wall bracket, pre-wired to GST 18/4 leads
• No visible screws and easy/cleaning access to the top of the luminaire
Order Codes
Florence Elite Standard
T5 1 x 39W up/1 x 21W down (Switch Dim) FEL3921 LED 2400 lumens up/1500 lumens down (DALI) FEY2415
To Specify Direct/indirect wall mounted hospital bed head luminaire using LED or T5 light source with separately switched dimmable ward lighting and reading/nursing care light. Easy to clean, IP40 rated extruded aluminium body with one piece infection control di�user membrane – as Whitecroft Lighting FLORENCE ELITE
Lamp PerformanceWattage IL@25°C Lamp Life1 x 21W T5 1900 24,000hrs1 x 39W T5 3100 24,000hrs
H L
W
Dimensions
L W H KG 895 213 95 5.0
7m
7m
100 luxFloor
Compact Pleiad G2 2x26W Downlight
300 lux
5m
3.6m
100 luxFloor
En Suite
Typical 4 Bed Ward Typical 1 Bed Ward
300 lux
40IP
322 HealthcareTYPICAL 4 BED WARD VS TYPICAL 1 BED WARD
FLO
REN
CE
ELIT
E
400 LUX
100%
25%
100%
3%
5%
5%
300 LUX
100LUX
5LUX
10LUX
400 LUX
100%
25%
100%
3%
5%
5%
300 LUX
100LUX
5LUX
10LUX
EXAMINATION
Medical practices carried out at bed space with curtains drawn.
400 LUX
100%
25%
100%
3%
5%
5%
300 LUX
100LUX
5LUX
10LUX
READING
Directly on the pillow, may be used as an additional source for nursing tasks. If adjustable avoidance of glare to others is essential.
400 LUX
100%
25%
100%
3%
5%
5%
300 LUX
100LUX
5LUX
10LUX
GENERAL/EMERGENCY
Centre ward illuminance should be sufficient to enable usual nursing procedures with consideration of overall ambience. Emergency lighting can also be incorporated into the central downlights.
400 LUX
100%
25%
100%
3%
5%
5%
300 LUX
100LUX
5LUX
10LUX
NIGHTLIGHT
Downlight only, visual acuity low. Illuminance sufficient to allow staff and patients to move around. Should not disturb sleeping patients.
WATCHLIGHT
Downlight only, continuous observation after the main switch off.
WARD ILLUMINANCE
Eagle lighting Australia’s recommended ward lighting scheme combines bedhead mounted up/downlights with ceiling mounted downlights to give maximum flexibility. Lighting can be patient controlled to maximise comfort with central override for staff to pre-set configurations.
PATIENT COMFORT
For the optimum blend of patient comfort and ease of maintenance, offset asymmetric lighting is ELA’s preferred solution to achieve a uniform 200 lux in corridors.
CENTRALLY MOUNTED
This can cause overhead glare and discomfort as patients are moved along hospital streets and corridors.
OFFSET TO THE SIDE
Overhead glare is significantly reduced with a recessed luminaire fitted with an asymmetric specular reflector.
IMPROVING EFFICIENCY
Corridors are as important as any other area of a hospital, so the same considerations of patient comfort, staff effectiveness and logistical efficiency apply. Lighting design needs to address all these issues, while the practical demands of cleaning and maintenance also come into play.
ELA’s experience and expertise are brought to bear fully in these situations, creating innovative solutions that provide the best possible lighting for all types of corridors. In particular, asymmetric distribution helps to reduce glare and create an anxiety-reducing environment, while longitudinal layouts improve both lighting quality and efficiency.
For ease of maintenance, corridor lighting units are designed to leave ceiling voids clear for services,
VISIBLE IMPROVEMENTSA practical and aesthetic lighting solution for corridors and hospital streets.
Centrally mountedThis can cause overhead glare anddiscomfort as patients are movedalong hospital streets and corridors.
Centrally mountedThis can cause overhead glare anddiscomfort as patients are movedalong hospital streets and corridors.
WELCOMING ENVIRONMENTSWelcoming, reassuring lighting for reception and communal areas.
ENHANCING PATIENT EXPERIENCE
Good lighting enhances patients’ experience in every area of a hospital, from the moment of arrival until final departure. The need to maintain a feeling of safety and security is crucial to that experience, especially in areas with easy public access and significant people movement.
ELA solutions help to create a sense of well-being and comfort through sympathetic design and use of warm lamp colours. For patients, staff and visitors, security is further ensured by well-planned installations that eliminate dark corners and illuminate unoccupied areas.
TECHNICAL INFORMATION
VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
1-10V/STD terminal block -300
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
1-10V/Fused terminal block -700
SWINGING LAMP HOLDER FOR LAMP REPLACEMENT
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C
GONDOL EXPOSED T-BAR
EL-17631-100 1 x 28W T5 1200 300 75
N18226
Recessed mounted IP44 asymmetric wall washer luminaire suitable for T-Bar ceilings. The lamp is concealed in the luminaire and hidden from view.
Asymmetrical light distribution for lighting vertical surfaces, the light sources lamp holder is pivoted so that the source can be moved into the light opening to facilitate re-lamping.
Acrylic dust proof cover for ease of cleaning.
OPTIONS
+ Seismic RestraintGONDOL 1x28W | LOR 80%
GONDOL IP44 RATED A wall washing T-Bar luminaire complete with sealed gasket and clear acrylic cover.
C
B
A
44
DIAGRAM OF WALLWASHING EFFECT
GO
ND
OL
www.eaglelighting.com.au 45
EPDM GASKET
TECHNICAL INFORMATION
VARIATION SUFFIX
Non DIM/STD terminal block -0
DSI/STD terminal block -1
DALI/STD terminal block -2
Standard/Fused terminal block -4
DSI/Fused terminal block -5
DALI/Fused terminal block -6
Emergency (ATCO maintained) -8
PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSWATTAGE EFFICACYlm/W
LUMINOUS FLUX A B C CUTOUT
CLEANROOM LED : BOTTOM ACCESS PLASTER RECESSED
EL-CR44L-814000P-_ 1R 2600LM 4k Delta 20 83 1650 1260 315 120 1230 285
EL-CR44L-824000P-_ 2R 5200LM 4k Delta 38.8 82 3172 1260 315 120 1230 285
EL-CR44L-814200P-_ 1R 1300LM 4k Delta 9.7 84.5 820 660 315 120 630 285
EL-CR44L-824200P-_ 2R 2600LM 4k Delta 20 82 1638 660 315 120 630 285
EL-CR44L-824100P-_ 2R 5200LM 4k Delta 38.8 87 3380 1260 660 120 1230 630
EL-CR44L-834100P-_ 3R 7800LM 4k Delta 58.5 87 5070 1260 660 120 1230 630
EL-CR44L-844100P-_ 4R 10400LM 4k Delta 77.8 87 6760 1260 660 120 1230 630
EL-CR44L-824300P-_ 2R 2600LM 4k Delta 20 84.5 1690 660 660 120 630 630
EL-CR44L-834300P-_ 3R 3900LM 4k Delta 29.7 85 2535 660 660 120 630 630
EL-CR44L-844300P-_ 4R 5200LM 4k Delta 38.8 86 3345 660 660 120 630 630
The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.
This range is rated IP44 from all angles.
The Cleanroom IP44 LED fitting is ideal for areas where long running hours and difficult access for maintenance are a concern.
The LED boards employed in the Cleanroom are Zhaga approved and can easily be changed or upgraded by two simple fixing screws. Using Zhaga approved boards ensures future availability and access to the latest developments in efficiency, colour quality and maintenace in the LED market.
Seismic restraint as standard.OPTIONS
+ Sandwich Panel
+ Emergency
+ Colour temperature 3k, 4k or 5k
N18226
CLEANROOM IP44 LEDA range of luminaires developed for specialist ‘cleanroom’ applications
Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
DIFFUSER PANEL OPTIONS SUFFIX
P19 -1
P5 -2
Delta -8
CEILING TYPE SUFFIX
Plaster -P
Surface mounted -S
T-bar -T
IES INDOOR REPORTPHOTOMETRIC FILENAME : LL16298.IES
POLAR GRAPH
207
414
620
827
1
Maximum Candela = 827.29 Located At Horizontal Angle = 0, Vertical Angle = 0# 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.)
Photometric Toolbox Professional Edition - Copyright 2002-2011 by Lighting Analysts, Inc.Calculations based on published IES Methods and recommendations, values rounded for display purposes.Results derived from content of manufacturers photometric file.
Page 1
CLEANROOM IP44 LED 1200x300 2600lm Delta
TECHNICAL SPECIFICATIONS
Total Luminaire Efficacy minimum > 69lm/W
MacAdam 3 SDCM
CRI > 84
Lifetime 50,000hrs / L70
Passive cooling
System guarantee 5 years
EXAMPLE ONLY
CEILING TYPE
COLOUR TEMP WIRING VARIATION
DIFFUSER OPTION
EL-CR44L-814000P-_B
C
A
TOGGLE
LED IP44
CLE
AN
RO
OM
IP44
www.eaglelighting.com.au 47
VARIATION SUFFIX
Non DIM/STD terminal block -0
DSI/STD terminal block -1
DALI/STD terminal block -2
Standard/Fused terminal block -4
DSI/Fused terminal block -5
DALI/Fused terminal block -6
Emergency (ATCO maintained) -8
DIFFUSER PANEL OPTIONS SUFFIX
P19 -1
P5 -2
Delta -8
CEILING TYPE SUFFIX
Plaster -P
Surface mounted -S
T-bar -T
TECHNICAL SPECIFICATIONS
Total Luminaire Efficacy minimum > 69lm/W
MacAdam 3 SDCM
CRI > 84
Lifetime 50,000hrs / L70
Passive cooling
System guarantee 5 years
EXAMPLE ONLY
CEILING TYPE
COLOUR TEMP WIRING VARIATION
DIFFUSER OPTION
EL-CR44L-81H4000P-_
EPDM GASKET
TECHNICAL INFORMATION
PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSWATTAGE EFFICACYlm/W
LUMINOUS FLUX A B C CUTOUT
CLEANROOM LED : BOTTOM ACCESS PLASTER RECESSED
EL-CR44L-81H4000P-_ 1R 5000LM 4k High Output Delta 36 82 2950 1260 315 120 1230 285
EL-CR44L-82H4000P-_ 2R 10000LM 4k High Output Delta 72 81 5828 1260 315 120 1230 285
EL-CR44L-81H4200P-_ 1R 2500LM 4k High Output Delta 18 82 1475 660 315 120 630 285
EL-CR44L-82H4200P-_ 2R 5000LM 4k High Output Delta 36 82 2949 660 315 120 630 285
EL-CR44L-82H4100P-_ 2R 9600LM 4k High Output Delta 72 84 6048 1260 660 120 1230 630
EL-CR44L-83H4100P-_ 3R 14400LM 4k High Output Delta 108.4 84 9126 1260 660 120 1230 630
EL-CR44L-82H4300P-_ 2R 4800LM 4k High Output Delta 36 84.5 3042 660 660 120 630 630
EL-CR44L-83H4300P-_ 3R 7200LM 4k High Output Delta 54.2 84 4563 660 660 120 630 630
EL-CR44L-84H4300P-_ 4R 9600LM 4k High Output Delta 72 84.5 6084 660 660 120 630 630
CLEANROOM IP44 LED HIGH OUTPUTA range of luminaires developed for specialist ‘cleanroom’ applications
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
CLEANROOM IP44 LED HO 1200x300 5000lm Delta
The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.
This range is rated IP44 from all angles.
The Cleanroom IP44 LED fitting is ideal for areas where long running hours and difficult access for maintenance are a concern.
The LED boards employed in the Cleanroom are Zhaga approved and can easily be changed or upgraded by two simple fixing screws. Using Zhaga approved boards ensures future availability and access to the latest developments in efficiency, colour quality and maintenace in the LED market.
Seismic restraint as standard.
OPTIONS
+ Sandwich Panel
+ Emergency
+ Colour temperature 3k, 4k or 5kN18226
Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg
B
C
A
1514
1
2
1135
378
757
TOGGLE
LED IP44
CLE
AN
RO
OM
IP44
TECHNICAL INFORMATION
GASKET
PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSA B C CUTOUT
CLEANROOM T5 : BOTTOM ACCESS GASKETED PLASTER RECESSED
EL-CR44-214-_02P-___ 2 x 14W T5 Plaster Recessed 660 315 120 630 285
EL-CR44-314-_02P-___ 3 x 14W T5 Plaster Recessed 660 315 120 630 285
EL-CR44-224-_02P-___ 2 x 24W T5 Plaster Recessed 660 315 120 630 285
EL-CR44-324-_02P-___ 3 x 24W T5 Plaster Recessed 660 315 120 630 285
EL-CR44-228-_00P-___ 2 x 28W T5 Plaster Recessed 1260 315 120 1230 285
EL-CR44-328-_00P-___ 3 x 28W T5 Plaster Recessed 1260 315 120 1230 285
EL-CR44-254-_00P-___ 2 x 54W T5 Plaster Recessed 1260 315 120 1230 285
EL-CR44-354-_00P-___ 3 x 54W T5 Plaster Recessed 1260 315 120 1230 285
EL-CR44-228-_01P-___ 2 x 28W T5 Plaster Recessed 1260 660 120 1230 630
EL-CR44-328-_01P-___ 3 x 28W T5 Plaster Recessed 1260 660 120 1230 630
EL-CR44-254-_01P-___ 2 x 54W T5 Plaster Recessed 1260 660 120 1230 630
EL-CR44-214-_03P-___ 2 x 14W T5 Plaster Recessed 660 660 120 630 630
EL-CR44-224-_03P-___ 2 x 24W T5 Plaster Recessed 660 660 120 630 630
EL-CR44-414-_03P-___ 4 x 14W T5 Plaster Recessed 660 660 120 630 630
44
CLEANROOM 2x28W Y19 | LOR >70%
8/
CLEANROOM IP44 T5A range of luminaires developed for specialist ‘cleanroom’ applications
The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.
This range is rated IP44 from all angles.
Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.
A large variety of speciality lamp options are easily available for the Cleanroom IP44 T5 and T8 models, including high colour rendering options, long life versions and cyanosis index approved options.
OPTIONS
+ Sandwich Panel
+ Emergency
+ Seismic Restraint
N18226
VARIATION SUFFIX
Non DIM/STD terminal block -000
DSI/STD terminal block -100
DALI/STD terminal block -200
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
Emergency (ATCO maintained) -800
Seismic restraint -900
DIFFUSER PANEL OPTIONS SUFFIX
P19 -1
P5 -2
Delta -8
EXAMPLE ONLY WIRING VARIATIONDIFFUSER OPTION
CEILING TYPELAMP TYPE
EL-CR44-214-_02P-___
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg
B
C
A
updated: 21.10.2013
TOGGLE
CLE
AN
RO
OM
IP44
TECHNICAL INFORMATION
GASKET TOGGLE
PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSA B C CUTOUT
CLEANROOM T8 : BOTTOM ACCESS GASKETED PLASTER RECESSED
EL-CR44-218-_02P-___ 2 x 18W T8 Plaster Recessed 660 315 120 630 285
EL-CR44-318-_02P-___ 3 x 18W T8 Plaster Recessed 660 315 120 630 285
EL-CR44-236-_00P-___ 2 x 36W T8 Plaster Recessed 1260 315 120 1230 285
EL-CR44-336-_00P-___ 3 x 36W T8 Plaster Recessed 1260 315 120 1230 285
EL-CR44-236-101P-___ 2 x 36W T8 Plaster Recessed 1260 660 120 1230 630
EL-CR44-336-101P-___ 3 x 36W T8 Plaster Recessed 1260 660 120 1230 630
EL-CR44-436-101P-___ 4 x 36W T8 Plaster Recessed 1260 660 120 1230 630
EL-CR44-218-103P-___ 2 x 18W T8 Plaster Recessed 660 660 120 630 630
EL-CR44-318-103P-___ 3 x 18W T8 Plaster Recessed 660 660 120 630 630
EL-CR44-418-103P-___ 4 x 18W T8 Plaster Recessed 660 660 120 630 630
The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.
This range is rated IP44 from all angles.
Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.
A large variety of speciality lamp options are easily available for the Cleanroom IP44 T5 and T8 models, including high colour rendering options, long life versions and cyanosis index approved options.
OPTIONS
+ Sandwich Panel
+ Emergency
+ Seismic Restraint
44
CLEANROOM 2x36W Y19 | LOR >70%
8/
CLEANROOM IP44 T8A range of luminaires developed for specialist ‘cleanroom’ applications
N18226
VARIATION SUFFIX
Non DIM/STD terminal block -000
DSI/STD terminal block -100
DALI/STD terminal block -200
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
Emergency (ATCO maintained) -800
Seismic restraint -900
DIFFUSER PANEL OPTIONS SUFFIX
P19 -1
P5 -2
Delta -8
EXAMPLE ONLY WIRING VARIATIONDIFFUSER OPTION
CEILING TYPELAMP TYPE
EL-CR44-214-_02P-___
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg
B
C
A
362
2
91
181
272
1
updated: 21.10.2013
CLE
AN
RO
OM
IP44
CLEANROOM IP54 RATEDA range of luminaires developed for specialist ‘cleanroom’ applications
548/
TECHNICAL INFORMATION
VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
1-10V/STD terminal block -300
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
1-10V/Fused terminal block -700
TORSION SPRING
91
182
273
364
1
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C
CLEANROOM T5 : BOTTOM ACCESS TRIPLE GASKET
EL-CCL-214-_03-___ 2 x 14W T5 Plaster Recessed 650 650 135 615 615
EL-CCL-314-_03-___ 3 x 14W T5 Plaster Recessed 650 650 135 615 615
EL-CCL-414-_00-___ 4 x 14W T5 Plaster Recessed 650 650 135 615 615
EL-CCL-228-_00-___ 2 x 28W T5 Plaster Recessed 1275 370 135 1230 340
EL-CCL-328-_00-___ 3 x 28W T5 Plaster Recessed 1275 370 135 1230 340
EL-CCL-235-_00-___ 2 x 35W T5 Plaster Recessed 1575 370 135 1530 340
CLEANROOM T5 : TOP ACCESS TRIPLE GASKET
EL-CCL-228-_01-___ 2 x 28W T5 Plaster Recessed 1275 350 135 1230 340
EL-CCL-328-_01-___ 3 x 28W T5 Plaster Recessed 1275 350 135 1230 340
CLEANROOM T8 : BOTTOM ACCESS TRIPLE GASKET
EL-CCL-236-_00-___ 2 x 36W T8 Plaster Recessed 1275 370 135 1230 340
EL-CCL-336-_00-___ 3 x 36W T8 Plaster Recessed 1275 370 135 1230 340
CLEANROOM T8 : TOP ACCESS TRIPLE GASKET
EL-CCL-236-_01-___ 2 x 36W T8 Plaster Recessed 1275 350 135 1230 340
EL-CCL-336-_01-___ 3 x 36W T8 Plaster Recessed 1275 350 135 1230 340
The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the clean environment.
Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.
OPTIONS
+ Plaster Recessed
+ Exposed T-Bar
+ Sandwich Panel
+ Emergency CO D16/ C90 D20 (3x36W Version)
+ Surface mounted version available upon request
+ Seismic Restraint
DIFFUSER PANEL OPTIONS SUFFIX
P19 -1
P5 -2
P7 -3
Opal -5
P20 -6
P19 Silver tint -7
CLEANROOM 2x28W | LOR 76%
N18226 REVIT IES AGi32
EXAMPLE ONLY
WIRING VARIATION
DIFFUSER OPTION
LAMP TYPE
EL-CCL-214-_03-___
GASKET
B
C
A
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
CLE
AN
RO
OM
IP54
CLEANROOM CLB IP54 RATEDA range of luminaires developed for specialist ‘cleanroom’ applications
54 IK10
TECHNICAL INFORMATION
VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
1-10V/STD terminal block -300
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
1-10V/Fused terminal block -700
The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the clean environment.
Ensuring a clean and secure environment does not negate the need for excellent light control. With the CLB we have incorporated the Penta G2 Miro 5 louvre fixed into the frame for increased luminance and glare control protected by a clear acrylic overlay.
Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.
OPTIONS
+ Plaster Recessed
+ Sandwich Panel
+ Surface mounted version available upon request
+ Polycarbonate (IK10)
+ Seismic Restraint
GASKET
97
195
292
390
1
CLEANROOM CLB 2x28W | LOR 83%
B
C
A
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C
CLEANROOM CLB PLASTER RECESSED
EL-CLB-214-100-_00 2 x 14W 650 370 100 620 290
EL-CLB-224-100-_00 2 x 24W 650 370 100 620 290
EL-CLB-314-100-_00 3 x 14W 650 450 100 620 400
EL-CLB-324-100-_00 3 x 24W 650 450 100 620 400
EL-CLB-414-100-_00 4 x 14W 650 650 100 620 510
EL-CLB-424-100-_00 4 x 24W 650 650 100 620 510
EL-CLB-228-100-_00 2 x 28W 1275 370 100 1230 290
EL-CLB-254-100-_00 2 x 54W 1275 370 100 1230 290
N18226 REVIT IES AGi32
EXAMPLE ONLY
LAMP TYPE WIRING VARIATION
EL-CLB-214-100-_00
TORSION SPRING
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
CLE
AN
RO
OM
CLB
SEC
UR
ERO
OM
SECUREROOM IP65 RATEDA range of luminaires specifically developed for specialist cleanroom and security applications
FD T2665 IK10
TECHNICAL INFORMATION
VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
1-10V/STD terminal block -300
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
1-10V/Fused terminal block -700
PC2 Acrylic panel -P
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C
SECUREROOM T5 BOTTOM ACCESS TRIPLE GASKET - PLASTER
EL-CCL-214-_04-___ 2 x 14W T5 Plaster Recessed 700 700 135 630 630
EL-CCL-314-_04-___ 3 x 14W T5 Plaster Recessed 700 700 135 630 630
EL-CCL-228-_05-___ 2 x 28W T5 Plaster Recessed 1300 400 135 1230 340
EL-CCL-328-_05-___ 3 x 28W T5 Plaster Recessed 1300 400 135 1230 340
EL-CCL-235-_02-___ 2 x 35W T5 Plaster Recessed 1600 400 135 1530 340
SECUREROOM T8 BOTTOM ACCESS TRIPLE GASKET - PLASTER
EL-CCL-418-_05-___ 4 x 18W T8 Plaster Recessed 700 700 135 630 630
EL-CCL-236-_02-___ 2 x 36W T8 Plaster Recessed 1300 400 135 1230 340
EL-CCL-336-_02-___ 3 x 36W T8 Plaster Recessed 1300 400 135 1230 340
NOTE : STANDARD COMPLETE WITH POLYCARBONATE. FOR PC2 ENVIRONMENT, ACRYLIC PANEL REPLACES POLYCARBONATE (ADD SUFFIX -P)
EPDM GASKETTAMPERPROOF SCREW
91
182
273
364
1
The Cleanroom Security range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the secure environment.
Suitable for diverse applications such PC2 laboratories, hospitals, psychiatric wards, police stations, high security, pharmaceutical manufacturing areas and applications where a clean and secure environment is required.
OPTIONS
+ Sandwich Panel
+ Emergency CO D16 / C90 D20 (3x36W Version)
+ Surface mounted available upon request
+ PC2 Environments
+ Seismic Restraint
DIFFUSER PANEL OPTIONS SUFFIX
P19 -1
P5 -2
P7 -3
Opal -5
P20 -6
P19 Silver tint -7
SECUREROOM 2x28W | LOR 76%
B
C
A
N18226 REVIT IES AGi32
EXAMPLE ONLY
WIRING VARIATIONLAMP TYPE
DIFFUSER OPTION
EL-CCL-214-_04-___
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
SEC
UR
ERO
OM
SLB
IK10
SECUREROOM SLB IP65 RATEDA range of luminaires specifically developed for specialist cleanroom and security applications
65
TECHNICAL INFORMATION
VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
1-10V/STD terminal block -300
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
1-10V/Fused terminal block -700
PC2 Acrylic panel -P
EPDM GASKETTAMPERPROOF SCREW
The Cleanroom Security range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the secure environment.
Having a clean and secure environment does not negate the need for excellent light control. With Secureroom SLB we have incorporated the Penta G2 Miro 5 louvre fixed into the frame for increased luminance and glare control.
Suitable for diverse applications such PC2 laboratories, hospitals, psychiatric wards, police stations, high security, pharmaceutical manufacturing areas and applications where a clean and secure environment is required.
OPTIONS
+ Sandwich Panel
+ Surface mounted available upon request
+ PC2 environments
+ Seismic Restraint
97
195
292
390
1
SECUREROOM SLB 2x28W | LOR 83%
B
C
A
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C
SECUREROOM SLB PLASTER RECESSED
EL-SLB-214-100-_00 2 x 14W 700 400 100 620 290
EL-SLB-224-100-_00 2 x 24W 700 400 100 620 290
EL-SLB-314-100-_00 3 x 14W 700 500 100 620 400
EL-SLB-324-100-_00 3 x 24W 700 500 100 620 400
EL-SLB-414-100-_00 4 x 14W 700 700 100 620 510
EL-SLB-424-100-_00 4 x 24W 700 700 100 620 510
EL-SLB-228-100-_00 2 x 28W 1300 400 100 1230 290
EL-SLB-254-100-_00 2 x 54W 1300 400 100 1230 290
NOTE : STANDARD COMPLETE WITH POLYCARBONATE. FOR PC2 ENVIRONMENT, ACRYLIC PANEL REPLACES POLYCARBONATE (ADD SUFFIX -P)
N18226 REVIT IES AGi32
EXAMPLE ONLY
WIRING VARIATIONLAMP TYPE
EL-CLB-214-100-_00
PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.
OP
ERA
TIN
G T
HEA
TRE
OPERATING THEATRE LIGHT A range of luminaires specifically developed for operating theatre applications
WIRING VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
1-10V/STD terminal block -300
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
1-10V/Fused terminal block -700
Our Operating Theatre Light luminaires have been developed as a unique solution, meeting the requirements of specialist operating theatre installations, where a fully sealed luminaire is needed to prevent contamination of the secure environment.
This range has been engineered specifically for hospitals, emergency and veterinarian operating theatres.
OPTIONS:
+ Available in an IP44 Cleanroom, or IP65 Secureroom configuration, with bottom or ceiling access.
+ T5 or T8 lamp options in single or multiple configurations.
+ Operating Theatre Light can be installed with separate switching/dimming depending on requirements.
+ Seismic Restraint
DIFFUSER PANEL OPTIONS SUFFIX
P19 -100
P5 -200
P7 -300
Opal -500
P20 -600
TECHNICAL INFORMATION
B
C
A
N18226
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONS†
A B C
OPERATING THEATRE LIGHT - BOTTOM ACCESS, TRIPLE GASKET - PLASTER RECESSED
EL-OPS-228-_00-000* CORNER A 1300† 400† 135†
EL-OPS-228-_01-000* CORNER B 1300† 400† 135†
EL-OPS-228-_02-000* INTERMEDIATE 1300† 400† 135†
EL-OPS-228-_03-000* INTERMEDIATE W/ CEILING ACCESS 1300† 400† 135†
EL-OPS-228-_04-000* START 1300† 400† 135†
EL-OPS-228-_05-000* END 1300† 400† 135†
*PRODUCT CODES AND †DIMENSIONS LISTED ARE EXAMPLES AND APPLY TO 2 X 28W LAMP CONFIGURATION ONLY
The Operating Theatre Light can be customised to your needs. Please consult with an ELA Representative regarding dimensions and product codes.
The Operating Theatre Light is available in the following lamp configurations:
T5 Lamp 14W 24W 28W 35W 49W 54W Single or Multiple Lamps
T8 Lamp 18W 36W 58W Single or Multiple Lamps
UNIQUE OVERLAPPING DESIGN EPDM GASKET & INSTALLATION BRACKETS
OPERATING THEATRE 2x28W | LOR 76%
91
182
273
364
1
6544
8/
EL-OPS-228-_00-000WIRING VARIATIONEXAMPLE ONLY
DIFFUSER OPTIONSLAMP CONFIGURATION
OP
ERA
TIN
G T
HEA
TRE
OPERATING THEATRE LIGHT A range of luminaires specifically developed for operating theatre applications
FEATURES & BENEFITS
EXAMPLE LAYOUTS Adapted from our highly successful Cleanroom and Secureroom range of luminaires, the Operating Theatre Light has been specifically developed to meet the demanding requirements of the theatre environment.
FEATURES AND BENEFITS:
+ Together with an EPDM gasket, swing-out installation brackets negate the need for a silicon sealant around the fixture in the ceiling. EPDM rubber foam is a closed cell gasket, ensuring a high IP-rating. At less than 10% compression this returns a 100% water tightness. The low-memory nature of the material ensures it will always return to its original shape.
+ Overlapping design construction, provides this system with a continuous seal around the perimeter of the installation.
+ UV-stablised, acrylic diffuser options contribute to the overall IP65-rating, and are easily cleaned and maintained. When compared with polycarbonate options, our acrylic diffuser is resistant to hospital-grade cleaners.
+ By combining the acrylic diffuser with the multi-directional IP-rating of the Operating Theatre Light, the result is a luminaire that meets the tough standards required for a PC2 environment.
+ One of the features of meeting the PC2 standard is that zero contaminants can enter the luminaire - including from inside the ceiling cavity. This means the luminaire achieves high maintenance intervals.
+ A removeable gear tray allows for easy installation and maintenance.
Designed and manufactured in Melbourne, Australia, the Operating Theatre Light has many unique features and capabilities, but most importantly offers a diverse range of options to suit applications with different constraints and requirements. Consult with your local ELA Representative to discuss your needs.
The above example layouts demonstrate how the Operating Theatre Light system can be installed to create a fully sealed, contaminant-free environment. Example A. demonstrates a full theatre installation, utilising Corner modules, Example B. shows a single run making use of Start and End modules.
2 2
0
1
EXAMPLE A. EXAMPLE B.
ITEM NO.
DESCRIPTION QTY
0 CORNER A 2
1 CORNER B 2
2 INTERMEDIATE 10
ITEM NO.
DESCRIPTION QTY
2 INTERMEDIATE 2
4 START 1
5 END 1
1 4
0 5
AU
REL
ED V
ISTA
AURELED VISTAA slimline LED luminaire with a printed acrylic diffuser suitable for recessed mounting and T-bar ceilings.
The Aureled Vista has been developed with healthcare enivronments in mind. The Aureled Vista is available with a range of different imagery designed to promote a relaxing and reassuring environment for patients.
Using creative lighting solutions creates a non-institutional feel that puts patients at ease and makes it more likely that they relax and focus on healing.
The Aureled Vista can be a focal and discussion point for young children undergoing medical examinations. By giving patients something to concerntrate on they are less likely to become agitated.
Designed and constructed with a shallow 45mm profile the Aureled will slide into confined spaces. Coupled with a detachable gearbox incorporating a plug-and-play connector this luminaire is the perfect solution for locations where there are multiple services installed inside the ceiling space.
Once installed, the gearbox can be detached from the luminaire housing as required whether for upgrading to dimming or maintenance.
Available with:+ DSI Dimming+ DALI Dimming+ Emergency+ Colour Temperature 4k+ Seismic Restraint
N18226
(REMOTE GEAR)
PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C D
AURELED VISTA EXPOSED T-BAR
EL-AUR-____-C1-___ Aureled LED C1 600 600 45 40
EL-AUR-____-C2-___ Aureled LED C2 600 1200 45 40
EL-AUR-____-C3-___ Aureled LED C3 600 1800 45 40
EL-AUR-____-C4-___ Aureled LED C4 1200 1200 45 40
EL-AUR-____-C6-___ Aureled LED C6 1200 1800 45 40
EL-AUR-____-C9-___ Aureled LED C9 1800 1800 45 40
(REMOTE GEAR)
AUTUMN 1 (AUT1)
GALAXY 1 (GAL1)
SKY 1 (SKY1)
OCEAN 1 (OCE1)
BUTTERFLY 1 (BUT1)
SKY 2 (SKY2)
AVAILABLE CONFIGURATIONS
C1 C2 C3 C4 C6 C9
EXAMPLE ONLY
CONFIGURATION
WIRING VARIATION
IMAGE OPTION
EL-AUR-AUT1-C9-000
WIRING VARIATION SUFFIX
Standard -000
DSI/STD terminal block -100
DALI/STD terminal block -200
Standard/Fused terminal block -400
DSI/Fused terminal block -500
DALI/Fused terminal block -600
PLEASE NOTE: If you would like to use an alternative image or an alternative configuration, please inform us and we will provide you with the required image specifications.
P.O.A
LED IP44
www.eaglelighting.com.au [email protected]
VICTORIA 17-19 Jets Court Melbourne Airport VIC 3045 P 03 9344 7444 F 03 9344 7433
NEW SOUTH WALES Unit 4, 21 Mars Road Lane Cove NSW 2066 P 02 9420 5799 F 02 9420 5988
QUEENSLAND 53 Caswell Street East Brisbane QLD 4169 P 07 3891 0744 F 07 3891 0755
AUSTRALIAN CAPITAL TERRITORY M 0411 889 406
DISTRIBUTORS - AUSTRALIA
WESTERN AUSTRALIA H.I. LIGHTING PTY LTD 111 Broadway Bassendean WA 6054 P 08 9377 1322 F 08 9377 1761
SOUTH AUSTRALIA H.I. LIGHTING SA PTY LTD 8 Hender Avenue Magill SA 5072 P 08 8304 8500
TASMANIA SOUTHERN LIGHTING & DISTRIBUTION 34 Federal Street North Hobart TAS 7000 P 03 6231 5599 F 03 6231 5211
DISTRIBUTORS - NEW ZEALAND
AUCKLAND FAGERHULT NEW ZEALAND Level 1, 18A Neilpark Drive East Tamaki, Auckland 2013 M +64 21 655 609 M +64 21 509 248
WELLINGTON FAGERHULT NEW ZEALAND M +64 21 597 900
SOUTH ISLAND
P