ME 6505 – Dynamics of Machines€¦ · Equilibrium of members with two forces and torque Equilibrium of members with two couples. Equilibrium of members with four forces. (4) Principle

Fatima Michael College of Engineering & Technology

ME 6505 – Dynamics of Machines

UNIT – I - Force Analysis

LECTURE-I

(1) Introduction: If the acceleration of moving links in a mechanism is running with considerable amount of

linear and/or angular accelerations, inertia forces are generated and these inertia forces also must be overcome

by the driving motor as an addition to the forces exerted by the external load or work the mechanism does.

(2) Newton’s Law: First Law Everybody will persist in its state of rest or of uniform motion (constant

velocity) in a straight line unless it is compelled to change that state by forces impressed on it. This means that

in the absence of a non-zero net force, the center of mass of a body either is at rest or moves at a constant

velocity. Second Law A body of mass m subject to a force F undergoes an acceleration a that has the same

direction as the force and a magnitude that is directly proportional to the force and inversely proportional to the

mass, i.e., F = ma. Alternatively, the total force applied on a body is equal to the time derivative of linear

momentum of the body. Third Law The mutual forces of action and reaction between two bodies are equal,

opposite and collinear. This means that whenever a first body exerts a force F on a second body, the second

body exerts a force −F on the first body. F and −F are equal in magnitude and opposite in direction. This law is

sometimes referred to as the action-reaction law, with F called the "action" and −F the "reaction"

(3) Types of force Analysis:

Equilibrium of members with two forces

Equilibrium of members with three forces

Equilibrium of members with two forces and torque

Equilibrium of members with two couples.

Equilibrium of members with four forces.

(4) Principle of Super Position: Sometimes the number of external forces and inertial forces acting on a

mechanism are too much for graphical solution. In this case we apply the method of superposition. Using

superposition the entire system is broken up into (n) problems, where n is the number of forces, by considering

the external and inertial forces of each link individually. Response of a linear system to several forces acting

simultaneously is equal to the sum of responses of the system to the forces individually. This approach is useful

because it can be performed by graphically.

(5) Free Body Diagram: A free body diagram is a pictorial representation often used by physicists and

engineers to analyze the forces acting on a body of interest. A free body diagram shows all forces of all types

acting on this body. Drawing such a diagram can aid in solving for the unknown forces or the equations of1

FatimawwwMichael.studentsfocusCollegeofEngineering.&comTechnology



motion of the body. Creating a free body diagram can make it easier to understand the forces, and torques or

moments, in relation to one another and suggest the proper concepts to apply in order to find the solution to a

problem. The diagrams are also used as a conceptual device to help identify the internal forces—for example,

shear forces and bending moments in beams—which are developed within structures.

(6) D’Alemberts Principle: D'Alembert's principle, also known as the Lagrange–d'Alembert principle, is

a statement of the fundamental classical laws of motion. It is named after its discoverer, the French physicist

and mathematician Jean le Rond d'Alembert. The principle states that the sum of the differences between the

forces acting on a system and the time derivatives of the momenta of the system itself along any virtual

displacement consistent with the constraints of the system is zero.

(7) Dynamic Analysis of Four bar Mechanism: A four-bar linkage or simply a 4-bar or four-bar is

the simplest movable linkage. It consists of four rigid bodies (called bars or links), each attached to two others

by single joints or pivots to form closed loop. Four-bars are simple mechanisms common in mechanical

engineering machine design and fall under the study of kinematics.

Dynamic Analysis of Reciprocating engines.

Inertia force and torque analysis by neglecting weight of connecting rod.

Velocity and acceleration of piston.

Angular velocity and Angular acceleration of connecting rod.

Force and Torque Analysis in reciprocating engine neglecting the weight of connecting rod.Equivalent Dynamical SystemDetermination of two masses of equivalent dynamical system

(8) Turning Moment Diagram: The turning moment diagram is graphical representation of the

turning moment or crank effort for various positions of crank.

LECTURE-2

(9) Single cylinder double acting engine:

2




3




LECTURE-3

4




5




Lecture-4

6




LECTURE-5

7




LECTURE-6

8




9




LECTURE-7

10




LECTURE-8,9 & 10

11




12




UNIT – II BALANCING

(1) Introduction:

Balancing is the process of eliminating or at least reducing the ground forces and/or moments. It is achieved by

changing the location of the mass centres of links. Balancing of rotating parts is a well known problem. A

rotating body with fixed rotation axis can be fully balanced i.e. all the inertia forces and moments. For

mechanism containing links rotating about axis which are not fixed, force balancing is possible, moment

balancing by itself may be possible, but both not possible. We generally try to do force balancing. A fully force

balance is possible, but any action in force balancing severe the moment balancing.

(2) Balancing of rotating masses: The process of providing the second mass in order to counteract the

effect of the centrifugal force of the first mass is called balancing of rotating masses.

(3) Static balancing: The net dynamic force acting on the shaft is equal to zero. This requires that the line of

action of three centrifugal forces must be the same. In other words, the centre of the masses of the system must

lie on the axis of the rotation. This is the condition for static balancing.

(4) Dynamic balancing: The net couple due to dynamic forces acting on the shaft is equal to zero. The

algebraic sum of the moments about any point in the plane must be zero.

(5) Various cases of balancing of rotating masses:

Balancing of a single rotating mass by single mass rotating in the same plane.

Balancing of a single rotating mass by two masses rotating in the different plane.

Balancing of a several masses rotating in single plane.

Balancing of a several masses rotating in different planes.

13




14




16




17




18




19




21




22




(12) Balancing of single cylinder engine:

A single cylinder engine produces three main vibrations. In describing them we will assume that the

cylinder is vertical. Firstly, in an engine with no balancing counterweights, there would be an enormous

23




vibration produced by the change in momentum of the piston, gudgeon pin, connecting rod and crankshaft once

every revolution. Nearly all single-cylinder crankshafts incorporate balancing weights to reduce this. While

these weights can balance the crankshaft completely, they cannot completely balance the motion of the piston,

for two reasons. The first reason is that the balancing weights have horizontal motion as well as vertical motion,

so balancing the purely vertical motion of the piston by a crankshaft weight adds a horizontal vibration. The

second reason is that, considering now the vertical motion only, the smaller piston end of the connecting rod

(little end) is closer to the larger crankshaft end (big end) of the connecting rod in mid-stroke than it is at the top

or bottom of the stroke, because of the connecting rod's angle. So during the 180° rotation from mid-stroke

through top-dead-center and back to mid-stroke the minor contribution to the piston's up/down movement from

the connecting rod's change of angle has the same direction as the major contribution to the piston's up/down

movement from the up/down movement of the crank pin. By contrast, during the 180° rotation from mid-stroke

through bottom-dead-center and back to mid-stroke the minor contribution to the piston's up/down movement

from the connecting rod's change of angle has the opposite direction of the major contribution to the piston's

up/down movement from the up/down movement of the crank pin. The piston therefore travels faster in the top

half of the cylinder than it does in the bottom half, while the motion of the crankshaft weights is sinusoidal. The

vertical motion of the piston is therefore not quite the same as that of the balancing weight, so they can't be

made to cancel out completely. Secondly, there is a vibration produced by the change in speed and therefore

kinetic energy of the piston. The crankshaft will tend to slow down as the piston speeds up and absorbs energy,

and to speed up again as the piston gives up energy in slowing down at the top and bottom of the stroke. This

vibration has twice the frequency of the first vibration, and absorbing it is one function of the flywheel. Thirdly,

there is a vibration produced by the fact that the engine is only producing power during the power stroke. In a

four-stroke engine this vibration will have half the frequency of the first vibration, as the cylinder fires once

every two revolutions. In a two-stroke engine, it will have the same frequency as the first vibration. This

vibration is also absorbed by the flywheel.

(13) Balancing of inertial forces in the multi-cylinder engine:

In multi-cylinder engines the mutual counteractions of the various components in the Crank shaft

assembly are one of the essential factors determining the selection of the Crank shafts configuration and with it

the design of the engine itself. The inertial forces are Balanced if the common centre of gravity for all moving

crankshaft-assembly components lies at the crankshaft's midpoint, i.e. if the crankshaft is symmetrical (as

viewed from the front). The crankshaft's symmetry level can be defined using geometrical representations of

1st- and 2nd-order forces (star diagrams). The 2nd order star diagram for the four-cylinder in-line engine is

asymmetrical, meaning that this order is characterized by substantial free inertial Forces. These forces can be

balanced using two countershafts rotating in opposite directions at double the rate of the crankshaft (Lanchester

system).

24




(14) Partial balancing of Locomotives:

25




26




27




28




29




UNIT –III FREE VIBRATIONS

(1) Introduction:

When a system is subjected to an initial disturbance and then left free to vibrate on its own, the resulting vibrations are referred to as free vibrations .Free vibration occurs when a mechanical system is set off with an initial input and then allowed to vibrate freely. Examples of this type of vibration are pulling a childback on a swing and then letting go or hitting a tuning fork and letting it ring. The mechanical system will then vibrate at one or more of its "natural frequencies" and damp down to zero.

(2) Basic elements of vibration system:

Mass or InertiaSpringiness or Restoring elementDissipative element (often calleddamper)External excitation

(3) Causes of vibration: Unbalance: This is basically in reference to the rotatingbodies. The uneven distribution of mass in a rotating body contributes to the unbalance.A good example of unbalance relatedvibration would be the ―vibrating alert‖ in our mobile phones. Here a small amount of unbalanced weight is rotated by a motor causing thevibration which makes the mobile phone to vibrate. You would have experienced the same sort of vibration occurring in your front loaded washingmachines that tend to vibrate during the ―spinning‖ mode.

Misalignment: This is an other major cause of vibration particularly in machines thatare driven by motors or any other prime movers.

Bent Shaft: A rotating shaft that is bent also produces the the vibrating effect since itlosses it rotation capability about its center.

Gears in the machine: The gears in the machine always tend to produce vibration,mainly due to their meshing. Though this may be controlled to some extent, any problemin the gearbox tends to get enhanced with ease.

Bearings: Last but not the least, here is a major contributor for vibration. In majority ofthe cases every initial problem starts in the bearings and propagates to the rest of themembers of the machine. A bearing devoid of lubrication tends to wear out fast and failsquickly, but before this is noticed it damages the remaining components in the machineand an initial look would seem as if something had gone wrong with the othercomponents leading to the bearing failure.

(4) Effects of vibration:

30




(a)Bad Effects: The presence of vibration in any mechanical system produces unwanted noise, high

stresses, poor reliability, wear and premature failure of parts. Vibrations are a great source of human

discomfort in the form of physical and mental strains.

(b)Good Effects: A vibration does useful work in musical instruments, vibrating screens, shakers, relive painin physiotherapy.(5) Methods of reduction of vibration:

-unbalance is its main cause, so balancing of parts is necessary.

-using shock absorbers.

-using dynamic vibration absorbers.

-providing the screens (if noise is to be reduced)

(6) Types of vibratory motion:

Free Vibration

Forced Vibration

(7) Terms used vibratory motion: (a)Time period (or)period of vibration: It is thetime taken by a vibrating body to repeat the motion itself.time period is usuallyexpressed in seconds. (b) Cycle: It is the motion completed in one time period. (c)Periodic motion: A motion which repeats itself after equal interval of time.(d)Amplitude (X) The maximum displacement of a vibrating body from the mean position.it is usually expressed in millimeter. (e) Frequency (f) The number of cycles completed in one second is called frequency

(8) Degrees of freedom: The minimum number of independent coordinates required to specify the motion

of a system at any instant is known as D.O.F of the system.

(9) Single degree of freedom system:

The system shown in this figure is what is known as a Single Degree of Freedom system. We use theterm degree of freedom to refer to the number of coordinates that are required to specify completely the configuration of the system. Here, if the position of the mass of the system is specified then accordingly the position of the spring and damper are also identified. Thus we need just one coordinate (that of the mass) to specify the system completely and hence it is known as a single degree of freedom system.

31




(10) Two degree of freedom system:

A two degree of freedom system With reference to automobile applications, this is referred as ―quarter car‖ model. The bottom mass refers to mass of axle, wheel etc components which are below the suspension spring and the top mass refers to the mass of the portion of the car and passenger. Since we need to specify both the top andbottom mass positions to completely specify the system, this becomes a two degree of freedom system.

(11) Types of Vibratory motion:

32




33




34




35




36




37




38




39




40




41




42




43




44




45




46




47




48




UNIT-IV FORCED VIBRATION

Lecture-1

Forced Vibration:

When the body vibrates under the influence of external force, then the body is said to be under forced vibration.

Examples of forced vibration:

1. Ringing of electric bell.

2. Vibration of various machines like air compressor, IC engines, Machine tools and mobile cranes.

Types of external Excitation:

1. Periodic forces,

2. Impulse type of forces,

3. Random Forces.

Periodic forces are further classified into harmonic and non-harmonic forces. Vibration because of impulsive forces is called as

transient. Earthquake and acoustic excitation are typical examples of random forces. In this chapter we would be analysing only

about periodic forcing functions.

Frequency of Under Damped Forced Vibrations

Consider a system consisting of spring, mass and damper as shown in Fig. Let the system is acted upon by an external

periodic (i.e. simple harmonic) disturbing force,

Fx=F cosZ.t

whereF = Static force, and

Z= Angular velocity of the periodic disturbing force.

49




When the system is constrained to move in vertical guides, it has only one degree of freedom. Let at sometime t,

the mass is displaced downwards through a distance x from its mean position.

Important formulas to be remembered:

When Damping is negligible, then c = 0

At resonance Z = Zn. Therefore the angular speed at which the resonance occurs is

50




Lecture-2

Magnification Factor or Dynamic Magnifier

It is the ratio of maximum displacement of the forced vibration (xmax ) to the deflection due to the static

force F(xo). We have proved in the previous article that the maximum displacement or the amplitude of forced vibration,

51




The magnification factor or dynamic magnifier gives the factor by which the static deflection produced by a force F (i.e.xo) must

be multiplied in order to obtain the maximum amplitude of the forced vibration (i.e. x max) by the harmonic force FcosZ.t

1. If there is no damping (i.e. if the vibration is undamped), then c = 0. In that case, magnification factor,

2. At resonance, Z= Zn. Therefore magnification factor,

Problem-1

A single cylinder vertical petrol engine of total mass 300 kg is mounted upon a steel chassis frame and causes a vertical

static deflection of 2 mm. The reciprocating parts of the engine have a mass of 20 kg and move through a vertical stroke of 150

mm with simple harmonic motion. A dashpot is provided whose damping resistance is directly proportional to the velocity and

amounts to 1.5 kN per metre per second.

Considering that the steady state of vibration is reached; determine: 1. the amplitude of forced vibrations, when the driving shaft

of the engine rotates at 480 r.p.m, and 2. the speed of the driving shaft at which resonance will occur.

Given:

m = 300 kg; Z= 2 mm = 2 × 10–3 m ;m1 = 20 kg ; l = 150 mm= 0.15 m ; c = 1.5 kN/m/s = 1500 N/m/s ; N =

480 r.p.m. or Z 2π�480 / 60 = 50.3 rad/s

52




Lecture-3

Problem – 2

A mass of 10 kg is suspended from one end of a helical spring, the other end being fixed. The stiffness of the

spring is 10 N/mm. The viscous damping causes the amplitude to decrease to one-tenth of the initial value in four complete

oscillations. If a periodic force of 150 cos 50 t N is applied at the mass in the vertical direction, find the amplitude of the

forced vibrations. What is its value of resonance?

Given:

m = 10 kg; s = 10 N/mm = 10 × 103N/m ; X5 = X1 / 10

53




Amplitude of the forced vibrations

54




Lecture-4

Problem – 3

A single cylinder vertical petrol engine of total mass 300 kg is mounted upon a steel chassis frame and causes a

vertical static deflection of 2 mm. under this load. Calculate the frequency of free vibrations and verify that a viscous damping

force amounting to approximately 1000 N at a speed of 1 m/s is just-sufficient to make the motion aperiodic. If when damped to

this extent, the body is subjected to a disturbing force with a maximum value of 125 N making 8 cycles/s, find the amplitude of

the ultimate motion.

Given: m = 20 kg; c = 1000 N/m/s; F = 125 N ;f = 8 cycles/s

Frequency of free vibrations

We know that frequency of free vibrations,

The critical damping to make the motion aperiodic is such that damped frequency is zero,

This means that the viscous damping force is 1023 N at a speed of 1 m/s. Therefore a viscous damping force amounting to

approximately 1000 N at a speed of 1 m/s is just sufficient to make the motion aperiodic.

Amplitude of ultimate motion

We know that angular speed of forced vibration,

Z 2π�f 2π�8 50.3 rad/s

and stiffness of the spring, s = m.g/ δ= 20 × 9.81 / 0.015 = 13.1 × 103 N/m

Amplitude of ultimate motion i.e. maximum amplitude of forced vibration

55




Lecture-5

Problem-4

The time of free vibration of a mass hung from the end of a helical spring is 0.8 second. When the

mass is stationary, the upper end is made to move upwards with a displacement y metre such that y = 0.018 sin 2 Zt,

where t is the time in seconds measured from the beginning of the motion. Neglecting the mass of the spring and any

damping effects, determine the vertical distance through which the mass is moved in the first 0.3 second.

Given :tp= 0.8 s ; y = 0.018 sin 2 Zt

Let m = Mass hung to the spring in kg, and

s = Stiffness of the spring in N/m.

We know that time period of free vibrations (tp),

If x metres is the upward displacement of mass m from its equilibrium position after time t seconds, the equation of motion

is given by

56




Lecture-6

Vibration Isolation and Transmissibility

A little consideration will show that when an unbalanced machine is installed on the foundation, it produces vibration in

the foundation. In order to prevent these vibrations or to minimise the transmission of forces to the foundation, the machines are

mounted on springs and dampers or on some vibration isolating material, as shown in Fig. The arrangement is assumed to have

one degree of freedom, i.e. it can move up and down only.

It may be noted that when a periodic (i.e. simple harmonic) disturbing force F cosZt is applied to a machine of mass m

supported by a spring of stiffness s, then the force is transmitted by means of the spring and the damper or dashpot to the fixed

support or foundation.

The ratio of the force transmitted (FT) to the force applied (F) is known as the isolation factor or transmissibility ratio of

the spring support.

We have discussed above that the force transmitted to the foundation consists of the following two forces:

1. Spring force or elastic force which is equal to s. xmax, and

2. Damping force which is equal to c.Z.xmax.

Since these two forces are perpendicular to one another, as shown in Fig, therefore the force transmitted,

57




When the damper is not provided, then c = 0, and

From above, we see that when Z/Zn!1, ϵ is negative. This means that there is a phase difference of 180° between the transmitted force and the disturbing force (F cosZ.t).The value of Z/Znmust be greater than 2 if ϵ is to be less than 1 and it is the numerical value of ϵ , independent of any phase difference between the forces that may existwhich is important. It is therefore more convenient to use equation (ii) in the following form, i.e.

Fig below is the graph for different values of damping factor c/cc to show the variation of transmissibility ratio (ϵ ) against the ratio Z/Zn.1. When Z/Zn 2, then all the curves pass through the point ϵ = 1 for all values of damping factor c/cc.

58




2. When Z/Zn2, then ϵ > 1 for all values of damping factor c/cc. This means that the force transmitted to the foundation through elastic support is greater than the force applied.3. When Z/Zn!2, then ϵ < 1 for all values of damping factor c/cc. This shows thatthe force transmitted through elastic support

is less than the applied force. Thus vibration isolationis possible only in the range of Z/Zn ! 2

We also see from the curves in Fig above that the damping is detrimental beyond Z/Zn ! 2 and advantageous only in the

region Z/Zn < 2. It is thus concluded that for the vibration isolation, dampers need not to be provided but in order to limit

resonance amplitude, stops may be provided.

Lecture-7

Problem-5

The mass of an electric motor is 120 kg and it runs at 1500 r.p.m. The armature mass is 35 kg and its C.G. lies

0.5 mm from the axis of rotation. The motor is mounted on five springs of negligible damping so that the force transmitted is59




one-eleventh of the impressed force. Assume that the mass of the motor is equally distributed among the five springs. Determine:

1. stiffness of each spring; 2. dynamic force transmitted to the base at the operating speed; and 3. natural frequency of the

system.Given m1 = 120 kg; m2 = 35 kg; r = 0.5 mm = 5 × 10–4 m; ϵ = 1 / 11; N = 1500 r.p.m. or Z= 2π× 1500 / 60 = 157.1

rad/s;

1. Stiffness of each spring

Let s = Combined stiffness of the spring in N-m, and Zn = Natural circular frequency of vibration of the machine in rad/s. We know that transmissibility ratio (ϵ ),

Lecture-8

Problem-6

60




A machine has a mass of 100 kg and unbalanced reciprocating parts of mass 2 kg which move through a vertical stroke

of 80 mm with simple harmonic motion. The machine is mounted on four springs, symmetrically arranged with respect to centre

of mass, in such a way that the machine has one degree of freedom and can undergo vertical displacements only.

Neglecting damping, calculate the combined stiffness of the spring in order that the force transmitted to the foundation is 1 / 25

th of the applied force, when the speed of rotation of machine crank shaft is 1000 r.p.m.

When the machine is actually supported on the springs, it is found that the damping reduces the amplitude of successive free

vibrations by 25%. Fin: 1. the force transmitted to foundation at 1000 r.p.m., 2. the force transmitted to the foundation at

resonance, and 3. the amplitude of theforced vibration of the machine at resonance.Given: m1 = 100 kg ;m2 = 2 kg ; l = 80 mm = 0.08 m ; ϵ = 1 / 25 ; N = 1000 r.p.m. or Z 2π�1000 / 60 = 104.7 rad/s

Combined stiffness of springs

Let s = Combined stiffness of springs in N/m, and

Zn = Natural circular frequency of vibration of the machine in rad/s.We know that transmissibility ratio (ϵ ),

1. Force transmitted to the foundation at 1000 r.p.m.

Let FT = Force transmitted, and

x1 = Initial amplitude of vibration.

Since the damping reduces the amplitude of successive free vibrations by 25%, therefore final amplitude of vibration,

x2 0.75 x1

We know that damping coefficient or damping force per unit velocity,

61




c a X 2m1 0.94�2�100 = 188 N/m/s

and critical damping coefficient, cc 2m.Zn 2�100�20.5 = 4100 N/m/s

Actual value of transmissibility ratio,

62




Lecture-9

Problem – 7

A single-cylinder engine of total mass 200 kg is to be mounted on an elastic support which permits vibratory

movement in vertical direction only. The mass of the piston is 3.5 kg and has a vertical reciprocating motion which may be

assumed simple harmonic with a stroke of 150 mm. It is desired that the maximum vibratory force transmitted through the elastic

support to the foundation shall be 600 N when the engine speed is 800 r.p.m. and less than this at all higher speeds.

1. Find the necessary stiffness of the elastic support, and the amplitude of vibration at 800 r.p.m., and

2. If the engine speed is reduced below 800 r.p.m. at what speed will the transmitted forceagain becomes 600 N?

Given :m1 = 200 kg ; m2 = 3.5 kg ; l = 150 mm = 0.15 mm or r = l/2 = 0.075 m ;FT = 600 N ; N = 800 r.p.m.

or Z 2π�800 / 60 = 83.8 rad/s

We know that the disturbing force at 800 r.p.m.,

F = Centrifugal force on the piston

m2.Z ﾧ.r = 3.5 (83.8)2 0.075 = 1843 N

1. Stiffness of elastic support and amplitude of vibration

Let s = Stiffness of elastic support in N/m, and

xmax= Max.amplitude of vibration in metres.

Since the max.vibratory force transmitted to the foundation is equal to the force on the elastic support neglecting damping),

therefore Max.vibratory force transmitted to the foundation,

FT = Force on the elastic support

= Stiffness of elastic support × Max.amplitude of vibration

63




Lecture-10

Problem-8

A single cylinder vertical petrol engine of total mass 300 kg is mounted upon a steel chassis frame and causes a vertical

static deflection of 2 mm. The reciprocating parts of the engine have a mass of 20 kg and move through a vertical stroke of 150

mm with simple harmonic motion. A dashpot is provided whose damping resistance is directly proportional to the velocity and

amounts to 1.5 kN per metre per second.

Considering that the steady state of vibration is reached; determine: 1. the amplitude of forced vibrations, when the driving shaft

of the engine rotates at 480 r.p.m, and 2. the speed of the driving shaft at which resonance will occur.

64




Given:

m = 300 kg; Z= 2 mm = 2 × 10–3 m ;m1 = 20 kg ; l = 150 mm= 0.15 m ; c = 1.5 kN/m/s = 1500 N/m/s ; N =

480 r.p.m. or Z 2π�480 / 60 = 50.3 rad/s

Lecture-11

Problem-9

The mass of a single degree damped vibrating system is 7.5 kg and makes 24 free oscillations in 14 seconds when disturbed from its equilibrium position. The amplitude of vibration reduces to 0.25 of its initial value after five oscillations. Determine: 1. stiffness of the spring, 2. logarithmic decrement, and 3. damping factor, i.e. the ratio of the system damping to critical damping.

Given: m = 7.5 kg

Since 24 oscillations are made in 14 seconds, therefore frequency of free

vibrations, fn= 24/14 = 1.7 and Zn 2π.fn 2π�1.7 10.7 rad/s

65




Lecture-12Problem-10

A machine of mass 75 kg is mounted on springs and is fitted with a dashpot to damp out vibrations. There are

three springs each of stiffness 10 N/mm and it is found that the amplitude of vibration diminishes from 38.4 mm to 6.4 mm in

two complete oscillations.

Assuming that the damping force varies as the velocity, determin :1. the resistance of the dashpot at unit velocity ; 2. the ratio of

the frequency of the damped vibration to the frequency of the undamped vibration ; and 3. the periodic time of the damped

vibration.

66




Given: m = 75 kg ;s = 10 N/mm = 10 ×103 N/m ; x1 = 38.4 mm = 0.0384 m ; x3 = 6.4 mm = 0.0064

m Since the stiffness of each spring is 10 × 103 N/m and there are 3 springs, therefore total stiffness,

s 3X10X103 30X103 N/m

We know that natural circular frequency of motion,

67




UNIT-V MECHNISMS FOR CONTROL

Lecture-1

Types of Mechanisms for control are

1) Governors.2) Gyroscope.

Governors:

The function of a governor is to regulate the mean speed of an engine, when there arevariations in the load when the load on an engine increases, its speed decreases, therefore it becomesnecessary to increase the supply of working fluid. On the other hand, when the load on the enginedecreases, its speed increases and thus less working fluid is required. The governor automatically controlsthe supply of working fluid to the engine with the varying load conditions and keeps the mean speed withincertain limits.

68




Difference between a Flywheel and Governor:

The function of a flywheel in an engine is entirely different from that of a governor. It controls the speed variation caused by the fluctuations of the engine turning moment during each cycle of operation. It does not control the speed variations caused by a varying load. The varying demand for power is met by the governor regulating the supply of working fluid.

Types of Governors

The governors may, broadly, be classified as1. Centrifugal governors2. Inertia governors.

Centrifugal governors:

The centrifugal governors are based on the balancing of centrifugal force on the rotating ballsby anequal and opposite radial force, known as the controlling force.It consists of two balls ofequal mass,which are attached to the arms as shown in Fig. These balls are known as governorballs or fly balls.

The balls revolve with a spindle, whichis driven by the engine through bevel gears. The upperends of the arms are pivoted to the spindle, so that theballs may rise up or fall down as they revolve about

69




thevertical axis. The arms are connected by the links to asleeve, which is keyed to the spindle. This sleeverevolveswith the spindle; but can slide up and down.The balls and the sleeve risewhen the spindlespeedincreases, and falls when the speed decreases. In orderto limit the travel of the sleeve in upward anddownwarddirections, two stops S, S are provided on thespindle. The sleeve isconnected by a bell crankleverto a throttle valve. The supply of the working fluid decreaseswhen the sleeve rises and increases whenit falls. When the load on the engine increases, the engine and the governor speed decreases. This results inthe decrease of centrifugal force on the balls. Hence the balls move inwards and the sleeve movesdownwards. The downward movement of the sleeve operates a throttle valve at the other end of the bellcrank lever to increase the supply of working fluid and thus the engine speed is increased. In this case, theextra power output is provided to balance the increased load. When the load on the engine decreases, theengine and the governor speed increases, which results in the increase of centrifugal force on the balls.Thus the balls move outwards and the sleeve rises upwards. This upward movement of the sleeve reducesthe supply of the working fluid and hence the speed is decreased. In this case, the power output is reduced.

Lecture-2

Terms Used in Governors

1. Height of a governor. It is the vertical distance from the centre of the ball to a point where the axes of thearms (or arms produced) intersect on the spindle axis. It is usually denoted by h.2. Equilibrium speed. It is the speed at which the governor balls, arms etc., are in complete equilibrium andthe sleeve does not tend to move upwards or downwards.3. Mean equilibrium speed. It is the speed at the mean position of the balls or the sleeve.4. Maximum and minimum equilibrium speeds. The speeds at the maximum and minimum radius ofrotation of the balls, without tending to move either way are known as maximum and minimum equilibriumspeeds respectively.Note : There can be many equilibrium speeds between the mean and the maximum and the mean and the minimum equilibrium speeds.5. Sleeve lift. It is the vertical distance which the sleeve travels due to change in equilibrium speed.

Watt Governor:

The simplest form of a centrifugal governor is a Watt governor, as shown in Fig. It isbasically aconical pendulum with links attached to a sleeve of negligible mass. The arms of thegovernor may beconnected to the spindle in the following three ways:1. The pivot P may be on the spindle axis as shown in Fig. (a).2. The pivot P may be offset from the spindle axis and the arms when produced intersect atO, as shown in Fig. (b).3. The pivot P may be offset, but the arms cross the axis at O, as shown in Fig.(c).

70




m = Mass of the ball in kg,

w = Weight of the ball in newtons = m.g,T = Tension in the arm in newtons,Z= Angular velocity of the arm and ball about the spindle axis in rad/s,r = Radius of the path of rotation of the ball i.e. horizontal distance from the centre of the ball to the spindle axis in metres,

FC = Centrifugal force acting on the ball in newtons = m.Z ﾧ.r, andh = Height of the governor in metres.

Problem-1Calculate the vertical height of a Watt governor when it rotates at 60 r.p.m. Also find the change in vertical height when its speed increases to 61 r.p.m.

Given: N1 = 60 r.p.m. ;N2 = 61 r.p.m.

Initial heightWe know that initial height,

Change in vertical height

We know that final height,

Change in vertical height= h1 – h2 = 0.248 – 0.24 = 0.008 m = 8 mm

Lecture-3

Porter Governor:

The Porter governor is a modification of a Watt’s governor, with central load attached to the sleeveas shown in Fig.(a). The load moves up and down the central spindle. This additional downward forceincreases the speed of revolution required to enable the balls to rise to any predetermined level. Considerthe forces acting on one-half of the governor as shown in Fig.(b).

71




m = Mass of each ball in kg,

w = Weight of each ball in newtons = m.g,M = Mass of the central load in kg,W = Weight of the central load in newtons = M.g,r = Radius of rotation in metres,h = Height of governor in metres,N = Speed of the balls in r.p.m.Z= Angular speed of the balls in rad/s = 2πN/60 rad/s,FC = Centrifugal force acting on the ball in newtons = m.Z2.r,T1 = Force in the arm in newtons,T2 = Force in the link in newtons,α= Angle of inclination of the arm (or upper link) to the vertical, andE= Angle of inclination of the link (or lower link) to the vertical.

1. When the length of arms are equal to the length of links and the points P and D lie on the same vertical line, thentanα= tanEor q = tanα/ tanE= 1

2. When the loaded sleeve moves up and down the spindle, the frictional force acts on it in a direction

opposite to that of the motion of sleeve.If F = Frictional force acting on the sleeve in newtons, then the equations (v) and (vi) may be written as

The + sign is used when the sleeve moves upwards or the governor speed increases and negative sign is used when the sleeve moves downwards or the governor speed decreases. Problem – 2

72




A Porter governor has equal arms each 250 mm long and pivoted on the axis of rotation.Each ball has a mass of 5 kg and the mass of the central load on the sleeve is 25 kg. Theradius of rotation ofthe ball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed.Find the minimum and maximum speeds and range of speed of the governor.

(AU 2006)

Gn :BP = BD = 250 mm = 0.25 m ; m = 5 kg ; M = 15 kg ; r1 = 150 mm = 0.15m; r 2 = 200 mm = 0.2 m

Minimum speed when r1 = BG = 0.15 m

Let N1 = Minimum speed.From Fig(a), we find that height of the governor,h PG – 0.2 m

N1 = 133.8 r.p.m.

Maximum speed when r2 = BG = 0.2 mLet N2 = Maximum speed.From Fig(b), we find that height of the governor,

N2 = 154.5 r.p.m

Range of speedWe know that range of speed= N2 – N1 = 154.4 – 133.8 = 20.7 r.p.m.

Lecture-4

Proell Governor

73




The Proell governor has the balls fixed at B and C to the extension of the links DF and EG,as shown in Fig (a). The arms FP and GQ are pivoted at P and Q respectively. Consider the equilibrium ofthe forces on one-half of the governor as shown in Fig (b). The instantaneous centre (I) lies on theintersection of the line PF produced and the line from D drawn perpendicular to the spindle axis. Theperpendicular BM is drawn on ID.

Problem – 3A governor of the Proell type has each arm 250 mm long. The pivots of the upper and lower

arms are 25 mm from the axis. The central load acting on the sleeve has a mass of 25 kg and the eachrotating ball has a mass of 3.2 kg. When the governor sleeve is in mid-position, the extension link of thelower arm is vertical and the radius of the path of rotation of the masses is175 mm. The vertical height ofthe governor is 200 mm.If the governor speed is 160 r.p.m. when in mid-position, find : 1. length of theextensionlink; and 2. tension in the upper arm.

Given: PF = DF = 250 mm = 0.25 m ;PQ = DH = KG = 25 mm = 0.025 m ; M = 25 kg ; m = 3.2 kg ; r = FG = 175 mm

= 0.175 m ; h = QG = PK = 200 mm = 0.2 m ; N = 160 r.p.m.

74




Length of the extension link

BF = BM – FM = 0.308 – 0.2 = 0.108 m = 108 mm

Tension in the upper arm

Problem – 4A Proell governor has equal arms of length 300 mm. The upper and lower ends of the arms

are pivoted on the axis of the governor. The extension arms of the lower links are each 80 mm long andparallel to the axis when the radii of rotation of the balls are 150 mm and 200 mm. The mass of each ball is10 kg and the mass of the central load is 100 kg. Determine the range of speed of thegovernor.

75




Lecture-5

Hartnell Governor

A Hartnell governor is a spring loaded governor as shown in Fig. 18.18. It consists of twobell crank levers pivoted at the points O,O to the frame. The frame is attached to the governor spindle andtherefore rotates with it. Each lever carries a ball at the end of the vertical arm OB and a roller at the end ofthe horizontal arm OR. A helical spring in compression provides equal downward forces on the two rollersthrough a collar on the sleeve. The spring force may be adjusted by screwing a nut up or down on thesleeve.

Hartnell governor

76




Positions of Hartnell governor

Minimum position:

Maximum Position:

Problem-5:In a spring loaded Hartnell type governor, the extreme radii of rotation of the balls are 80

mm and 120 mm. The ball arm and the sleeve arm of the bell crank lever are equal in length. The mass ofeach ball is 2 kg. If the speeds at the two extreme positions are 400 and 420 r.p.m., find : 1. the initialcompression of the central spring, and 2. the spring constant.

Given:

r1 = 80 mm = 0.08 m ;r2 = 120 mm = 0.12 m ; x = y ; m = 2 kg ; N1 = 400r.p.m. or Z ﾧ= 2 π× 400/60 = 41.9 rad/s ; N2 =420 r.p.m. or Z2= 2 π× 420/60 = 44 rad/s

Initial compression of the central spring

For Minimum Position:

For Maximum Position

77




Lift of the sleeve

Lecture-6

Problem-6:In a spring controlled governorof the type, as shown in Fig, the mass of each ball is1.5 kg

and the mass of the sleeve is 8 kg. The two arms ofthe bell crank lever are at right angles and theirlengthsare OB = 100 mm and OA = 40 mm. The distance ofthe fulcrum O of each bell crank lever from theaxis ofrotation is 50 mm and minimum radius of rotation of thegovernor balls is also 50 mm. Thecorrespondingequilibrium speed is 240 r.p.m. and the sleeve is requiredto lift 10 mm for an increase inspeed of 5 per cent. Findthe stiffness and initial compression of the spring.Given:

m = 1.5 kg; M = 8 kg; OB = x= 100 mm = 0.1 m; OA = y = 40 mm = 0.04 m; r = 50 mm= 0.05 m; r1 = 50 mm = 0.05 m; N1 = 240 r.p.m. orZ1= 2π× 240/60 = 25.14 rad/s; h = 10 mm = 0.01 m; Increase inspeed = 5%The spring controlled governor of the type, as shown in Fig, has the pivots for the bell crank lever on themoving sleeve. The spring is compressed between the sleeve and the cap which is fixed to the end of thegovernor shaft. The simplest way of analysing this type of governor is by taking moments about theinstantaneous centre of all the forces which act on one of the bell crank levers. The minimum position ofthe governor is shown in Fig(a).

78




The maximum position of the governor is shown in Fig.(b). From the geometry of thefigure,

79




Hartung Governor

A spring controlled governor of the Hartung type is shown in Fig (a). In this type of

governor, the vertical arms of the bell crank levers are fitted with spring balls which compress against the

frame of the governor when the rollers at the horizontal arm press against the sleeve.

S = spring force,FC = Centrifugal force,M = Mass on the sleeve, andx and y = Lengths of the vertical and horizontal arm of the bell crank lever resp.

80




Lecture-7

Problem – 6In a spring-controlled governor of the Hartung type, the length of the ball and sleeve arms

are 80 mm and 120 mm respectively. The total travel of the sleeve is 25 mm. In the mid position, eachspring is compressed by 50 mm and the radius of rotation of the mass centres is 140 mm. Each ball has amass of 4 kg and the spring has a stiffness of 10 kN/m of compression. The equivalent mass of thegovernor gear at the sleeve is 16 kg. Neglecting the moment due to the revolving masses when the arms areinclined, determine the ratio of the range of speed to the mean speed of the governor. Find, also, the speedin the mid-position.

Given:x = 80 mm = 0.08 mm; y = 120 mm = 0.12 m ;h = 25 mm = 0.025 m ; r = 140 mm = 0.14 m ; m = 4 kg ; s = 10

kN/m = 10 × 103N/m ; M = 16 kg ; Initial compression = 50 mm = 0.05 m

Mean speed of the governor

81




Wilson-Hartnell Governor

A Wilson-Hartnell governor is a governor in which the balls are connected by a spring in

tension as shown in Fig. An auxiliary spring is attached to the sleeve mechanism through a lever by means

of which the equilibrium speed for a given radius may be adjusted. The main spring may be considered of

two equal parts each belonging to both the balls. The line diagram of a Wilson- Hartnell governor is shown

in Fig.

Sensitiveness of GovernorsSensitiveness is defined as the ratio of the difference between the maximum and

minimum equilibrium speeds to the mean equilibrium speed.

Stability of Governors

A governor is said to be stable when for every speed within the working range there is a definite

configuration i.e. there is only one radius of rotation of the governor balls at which the governor is in

equilibrium. For a stable governor, if the equilibrium speed increases, the radius of governor balls must

also increase.

Note: A governor is said to be unstable, if the radius of rotation decreases as the speed increases.

Isochronous Governors

82




A governor is said to be isochronous when the equilibrium speed is constant (i.e. range of speed is

zero) for all radii of rotation of the balls within the working range, neglecting friction. The isochronism is

the stage of infinite sensitivity.

Haunting

A governor is said to be hunt if the speed of the engine fluctuates continuously above andbelow the mean speed. This is caused by a too sensitive governor which changes the fuel supplyby a large amount when a small change in the speed of rotation takes place.

Effort and Power of a Governor

The effort of a governor is the mean force exerted at the sleeve for a given percentage change of speed* (or lift of the sleeve). It may be noted that when the governor is running steadily, there is no force at the sleeve. But, when the speed changes, there is a resistance at the sleeve which opposes its motion. It isassumed that this resistance which is equal to the effort, varies uniformly from a maximum value to zero while the governor moves into its new position of equilibrium.

The power of a governor is the work done at the sleeve for a given percentage change of speed. It is the product of the mean value of the effort and the distance through which the sleeve moves.

Power = Mean effort × lift of sleeve

Lecture-8

Controlling force:

Governor running at a steady speed, the inward force acting on the rotating balls is known as

controlling force. It is equal and opposite to the centrifugal reaction. The Controlling force is given

by Controlling force, FC = m.Z2.r

The controlling force is provided by the weight of the sleeve and balls as in Porter governor and by the

spring and weight as in Hartnell governor (or spring controlled governor). When the graph between the

controlling force (F C) as ordinate and radius of rotation of the balls (r) as abscissa is drawn, then the graph

obtained is known as controlling force diagram. This diagram enables the stability and sensitiveness of the

governor to be examined and also shows clearly the effect of friction.

83




Controlling Force Diagram for Porter Governor

where Φis the angle between the axis of radius of rotation and a line joining a given point (say A)

onthe curve to the origin O.

Controlling Force Diagram for Spring-controlled Governors

The controlling force diagram for the spring controlled governors is a straight line, as shownin

Fig. We know that controlling force,

F C = m.Z2.r or FC /r = m.Z2

For the governor to be stable, the controlling force (FC) must increase as the radius of rotation(r) increases,

i.e. FC / r must increase as r increases. Hence the controlling force line AB when produced must intersect

the controlling force axis below the origin, as shown in Fig. The relation between the controlling force (FC)

84




and the radius of rotation (r) for the stability of spring controlled governors is given by the following

equation

FC = a.r– b------------------------------------------------------------------------ (i)

Where a and b are constants.

The value of b in equation (i) may be made either zero or positive by increasing the initial tension of the

spring. If b is zero, the controlling force line CD passes through the origin and the governor becomes

isochronous because FC /r will remain constant for all radii of rotation. The relation between the controlling

force and the radius of rotation, for an isochronous governor is, therefore,

FC = a.r----------------------------------------------------------------------------- (ii)

If b is greater than zero or positive, then FC /r decreases as r increases, so that the equilibrium speed of

the governor decreases with an increase of the radius of rotation of balls, which is impracticable. Such a

governor is said to be unstable and the relation between the controlling force and the radius of rotation is,

therefore

FC = a.r+ b------------------------------------------------------------------------ (iii)

Coefficient of Insensitiveness

We have assumed the governor to be frictionless. In actual practice, there is always friction

in the joints and operating mechanism of the governor. Since the frictional force always acts in the opposite

direction to that of motion, therefore, when the speed of rotation decreases, the friction prevents the

downward movement of the sleeve and the radial inward movement of the balls. On the other hand, when

the speed of rotation increases, the friction prevents the upward movement of the sleeve and radial outward

movement of the balls.

85




Lecture-9

Gyroscopic Couple:

Consider a disc spinning with an angular velocity Z rad/s about the axis of spin OX, in

anticlockwise direction when seen from the front, as shown in Fig(a). Since the plane in which the disc is

rotating is parallel to the plane YOZ, therefore it is called plane of spinning. The planeXOZ is a horizontal

plane and the axis of spin rotates in a plane parallel to the horizontal plane aboutan axis OY. In other words,

the axis of spin is said to be rotating or processing about an axis OY. Inother words, the axis of spin is said

to be rotating or processing about an axis OY (which is perpendicular to both the axes OX and OZ) at an

angular velocity ZP rap/s. This horizontal plane XOZ is called plane of precession and OY is the axis of

precession.

I = Mass moment of inertia of the disc about OX, andZ= Angular velocity of the disc.

Angular momentum of the disc= I.Z

Since the angular momentum is a vector quantity, therefore it may be represented by the vector ox , as

shown in Fig.(b). The axis of spin OX is also rotating anticlockwise when seen from the top about the axis

OY. Let the axis OX is turned in the plane XOZ through a small angle δT radians to the positionOX’ , in

time δtseconds. Assuming the angular velocity Z to be constant, the angular

momentum will now be represented by vector OX’.

Change in angular momentum = I.Z.δT

Rate of change of angular momentum86




The rate of change of angular momentum will result by the application of a couple to the disc, therefore the couple applied to the disc causing precession

Problem – 7

A uniform disc of diameter 300 mm and of mass 5 kg is mounted on one end of an arm of length 600 mm. The other end of the arm is free to rotate in a universal bearing. If the disc rotates about thearm with a speed of 300 r.p.m. clockwise, looking from the front, with what speed will it precess about the vertical axis?Given: d = 300 mm or r = 150 mm = 0.15 m ;m = 5 kg ; l = 600 mm = 0.6 m ; N = 300 r.p.m. or Z ﾧ π× 300/60 = 31.42 rad/s.

I = m.r2/2 = 5(0.15)2/2 = 0.056 kg-m2

Lecture-10

Effect of the Gyroscopic Couple on an Aeroplane

The top and front views of an aeroplane are shown in Fig (a). Let engine or propeller rotates in the clockwise direction when seen from the rear or tail end and the aeroplane takes a turn to the left.

87




Aeroplane taking left turn

Notes: 1. when the aeroplane takes a right turn under similar conditions as discussed above, the effect of the reactive gyroscopic couple will be to dip the nose and raise the tail of the aeroplane.2. When the engine or propeller rotates in anticlockwise direction when viewed from the rear or tail endand the aeroplane takes a left turn, then the effect of reactive gyroscopic couple will be to dip the nose and raise the tail of the aeroplane.3. When the aeroplane takes a right turn under similar conditions as mentioned in note 2 above, theeffect of reactive gyroscopic couple will be to raise the nose and dip the tail of the aeroplane.4. When the engine or propeller rotates in clockwise direction when viewed from the front and theaeroplane takes a left turn, then the effect of reactive gyroscopic couple will be to raise the tail and dip the noseof the aeroplane.5. When the aeroplane takes a right turn under similar conditions as mentioned in note 4-above, theeffect ofreactive gyroscopic couple will be to raise the nose and dip the tail of the aeroplane.

Problem – 8An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying

at 200 km per hr. The rotary engine and the propeller of the plane has a mass of 400 kg and a radius of gyration of 0.3 m. The engine rotates at 2400 r.p.m. clockwise when viewed from the rear. Find the gyroscopic couple on the aircraft and state its effect on it.Given :R = 50 m ; v = 200 km/hr = 55.6 m/s ; m = 400 kg ; k = 0.3 m ;

N = 2400 r.p.m. or Z= 2π× 2400/60 = 251 rad/sWe know that mass moment of inertia of the engine and the propeller,

I = m.k2= 400(0.3)2= 36 kg-m2

and angular velocity of precession,ZP= v/R= 55.6/50 = 1.11 rad/s

We know that gyroscopic couple acting on the aircraft,88




C = I.ZZP= 36 × 251.4 × 1.11 = 100 46 N-m = 10.046 kN-m

When the aeroplane turns towards left, the effect of thegyroscopic couple is to lift the nose upwards andtail downwards.

Terms Used in a Naval Ship

The top and front views of a naval ship are shown in Fig. The fore end of the ship iscalled bow andthe rear end is known as stern or aft. The left hand and right hand sides of the ship,when viewed from thestern are called port and star-board respectively. We shall now discuss theeffect of gyroscopic couple on thenaval ship in the following three cases:

1. Steering, 2. Pitching and 3. Rolling.

Lecture-11

Effect of Gyroscopic Couple on a Naval Ship during Steering

Steering is the turning of a complete ship in a curve towards left or right, while it moves forward.Consider the ship taking a left turn, and rotor rotates in the clockwise direction when viewed from thestern, as shown in Fig. The effect of gyroscopic couple on a naval ship during steering taking left or rightturn may be obtained in the similar way as for an aeroplane as discussed earlier.

89




Effect of Gyroscopic Couple on a Naval Ship during Pitching

Effect of Gyroscopic Couple on a Naval Ship during Rolling

We know that, for the effect of gyroscopic couple to occur, the axis of precession should always beperpendicular to the axis of spin. If, however, the axis of precession becomes parallel to the axis of spin,there will be no effect of the gyroscopic couple acting on the body of the ship. In case of rolling of a ship,the axis of precession (i.e. longitudinal axis) is always parallel to the axis of spin for all positions. Hence,there is no effect of the gyroscopic couple acting on the body of a ship.

Problem – 9The turbine rotor of a ship has a mass of 8 tonnes and a radius of gyration 0.6 m. It rotates at

1800 r.p.m. clockwise, when looking from the stern. Determine the gyroscopic couple, if the ship travels at100 km/hr and steer to the left in a curve of 75 m radius.

Given:m = 8 t = 8000 kg; k = 0.6 m; N = 1800 r.p.m. or Z ﾧ π× 1800/60 = 188.5 rad/s; v = 100 km/h = 27.8

m/s; R = 75 m

Mass moment of inertia of the rotor,I = m.k2= 8000 (0.6)2= 2880 kg-m2

Angular velocity of precession,ZP= v / R = 27.8 / 75 = 0.37

rad/s Gyroscopic couple,C = I.ZZP= 2880 × 188.5 × 0.37 = 200 866 N-m

When the rotor rotates in clockwise direction when looking from the stern and the ship steers to theleft, the effect of the reactive gyroscopic couple is to raise the bow and lower the stern.

Problem – 10The turbine rotor of a ship has a mass of 3500 kg. It has a radius of gyration of 0.45 m and a

speed of 3000 r.p.m. clockwise when looking from stern. Determine the gyroscopic couple and its effectupon the ship:1. When the ship is steering to the left on a curve of 100 m radius at a speed of 36 km/h.

90




2. When the ship is pitching in a simple harmonic motion, the bow falling with its maximum velocity. Theperiod of pitching is 40 seconds and the total angular displacement between the two extreme positions ofpitching is 12 degrees.

Given: m = 3500 kg; k = 0.45 m; N = 3000 r.p.m. or Z ﾧ π× 3000/60 = 314.2 rad/s

Lecture-12

Stability of a Four Wheel Drive Moving in a Curved Path

91




92




A little consideration will show that when the vehicle is running at high speeds, PI may be zero or evennegative. This will cause the inner wheels to leave the ground thus tending to overturn the Automobile. Inorder to have the contact between the inner wheels and the ground, the sum of P/2 and Q/2 must be lessthan W/4.

Problem – 10:A four-wheeled trolley car of total mass 2000 kg running on rails of 1.6 mgauge, rounds a

curve of 30 m radius at 54 km/h. The track is banked at 8°. The wheels have an external diameter of 0.7 mand each pair with axle has a mass of 200 kg. The radius of gyration for each pair is 0.3 m. The height of centre of gravity of the car above the wheel base is 1 m. Determine, allowing for centrifugal force and gyroscopic couple actions, the pressure on each rail.

Given: m = 2000 kg ;x = 1.6 m ; R = 30 m ; v = 54 km / h = 15 m / s ; T= 8° ; dW= 0.7 m or rW= 0.35 m ; m1 = 200 kg ; k = 0.3 m ; h = 1 m

First of all, let us find the reactions RA and RB at the wheels A and B respectively. The various forcesacting on the trolley car are shown in Fig.

93




94




95


Documents

ME 6505 – Dynamics of Machines€¦ · Equilibrium of members with two forces and torque Equilibrium of members with two couples. Equilibrium of members with four forces. (4) Principle