Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003326REV A 11/29/04

MC1200Motorcycle Trailer - 1200 lbs.

Bundles Required:4300183 4.80 X 12-B Tire/MSilver Mod Rim65069 Lit Packet - SL Utility6562903 Frame Bundle MC1200 Black6838003 Bike Channel - Black

Tire Size & Carrying Capacity Chart:

Tire Size: ......................................... 4.80 X 12Load Range: .................................... BCarrying Capacity: ........................... 780 lbs.

MC1200 shown with ramp extended.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003326REV A 11/29/04

Assembly Instructions on Page 4.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003326REV A 11/29/04

Assembly Instructions:

Remove all small parts from the frame by cutting the bands. Re-move the bolt bag and sort all nuts and bolts by size.

Tongue:Remove tongue assembly from the frame bundle. Insert into the tongue channel and slide into the front cross member of the frame. Secure with two (2) 3/8” X 4” carriage bolts and 3/8” flange lock nuts. Tighten.

Thread the tongue wire harness through the front top hole in the tongue and pull out the hole provided in the left side of the tongue towards the rear. Connect to the frame harness with the plugs pro-vided. Install grommets.

Safety Chains:Insert a 3/8” X 1-1/4” hex bolt into a 3/8” flat washer, safety chain and then through the lower hole on the front of the tongue. Place on a 3/8” flat washer on the inside of the tongue and secure with 3/8” flange lock nuts.

Repeat procedure on the opposite side of the tongue. Tighten.

Coupler:Mount the coupler onto the tongue with a 1/2” X 4” hex bolt trough the rear mounting holes of the coupler. Using two (2) 1/2” X 1” hex bolt attach the coupler to the tongue using the front mounting holes. Secure with flange lock nuts. Tighten.

Axle:Attach the spring busing in the rear spring shackles with 1/2” X 3-1/4” hex bolts and 1/2” flange lock nuts.

Position the axle under the trailer with spring eye to the front of the trailer. Slip the flat end of the spring in the rear spring shackle above the bushing just installed. Secure the front spring eye to the front spring shackle with 98/16” X 3-1/4” hex bolts and 9/16” hex lock nuts. Tighten.

Mount the tire and rim assemblies to the axle assembly with 1/2” lug nuts and tighten to 80-90 ft./lbs. of torque using the rotation pat-tern as shown in the ShoreLand’r Owners Manual. Retorque the lug nuts after 50 miles of driving and then periodically thereafter.

Ramps:Locate the loading ramp. Note that one end has two holes punched in the bottom of the channel. (See parts drawing) Insert a 3/8” X 1-1/2” full threaded carriage bolt into one of these holes. Secure in this position using a 3/8” flange lock nut. Tighten Place a second 3/8” flange lock nut onto the same bolt only until the threads of the bolt are exposed through the nut locking it in place. Repeat the above process on the second bolt.

Note that the second nut installed on the bolt is used when loading and unloading your bikes. The ramp is attached to the bike chan-nels by dropping the two (2) bolts and nuts through the key hole slots provided in the rear of the bike channels. The nuts becomes locked in the slot when the ramp is moved either forward or back-ward. This will keep the ramp from becoming unhooked or rotating sideways when loading your bikes.

Secure the ramp under the trailer frame in the mounting brackets using the safety pin and 3/16” lynch pin provided.

Bike Support Channel:Mount the middle bike support channel to the tongue using a 3/8” x 3-7/16” x 4-1/8” square u-bolt, mounting strap and secure with two (2) 3/8” flange lock nuts. Secure the rear of the middle bike support channel to the rear cross channel on the frame using a 3/8” X 1” hex bolt, 3/8” flat washer and 3/8” flange lock nut.

Mount the two (2) outside bike support channels to the frame in the designated area on the frame using 3/8” hex bolts, 3/8” flat washers and 3/8” flange lock nuts.

Refer to the parts drawing for placement.

CAUTION:

The law requires that the white wire on both the tongue and the tow vehicle wire harness be grounded to the trailer and towing vehicle.

The ramp and all fasteners must be secure before towing.

Secure the motorcycle (s) with tie down straps firmly before tow-ing.

Tires must be inflated to the manufacturer’s standards. (Refer to the tire sidewall for PSI.)

Wheel bearings must have adequate grease. (Refer to the ShoreLand’r Owners Guide.)

The trailer coupler and coupler ball must be 2” diameter.

The coupler must be attached to the towing vehicle properly.

The trailer safety chains must be crossed under the tongue and attached to the towing vehicle.

All lights must be operational.

The trailer tongue jack must be in an up position or travel position when being towed.

DO NOT ride motorcycle (s) on loading ramp or trailer.