2
MC-Top Primer S Two component primer for Reparoxyd Substrate Preparation The cement based substrate must be at least 14 days old, dry and free from anti-adhesive sub- stances (e.g. oil, fat, release agent, loose particles etc.). At sub-zero temperatures the substrate must be defrosted and dried. Please refer to the data sheet „General Handling Information; Reparoxyd- Substrate preparation“. Mixing Mix the liquid component, using a trowel or spatu- la, with the powder component to a homogenous mixture. Even for small quantities (e.g. approx. 156 g liquid : 10 g powder) the mixing ratio of 100 : 6 must be observed. Application The cement based substrate is primed with MC- Top Primer S using roller or brush. For best results Reparoxyd should be applied after the primer has hardened, approx. after 1 - 2 hours. Special Information Colour changes may appear during processing because of chemical impact and influence of light. It doesn’t affect the usability. Chemical and mechanical impact areas are affected by wear. Regularly monitoring and routine maintenance are recommended. Further Information The hazard warnings and the safety advice on the packaging as well as the safety data sheet must be observed. Product Properties Areas of Application • Primer for Reparoxyd-Systems for repair of small scale concrete areas • Assesed by REACH exposure scenarios: to be inhaled only periodically during application • Two component • Based on special acrylate • Can be recoated immediately • Workable at temperatures below 0 °C Application Notes MC-Bauchemie • Am Kruppwald 1-8 • 46238 Bottrop • Tel. +49 (0) 2041-101 50 • Fax: +49 (0)2041-101 588 [email protected]www.mc-bauchemie.de

MC-Top Primer S

Embed Size (px)

DESCRIPTION

fisa tehnica

Citation preview

Page 1: MC-Top Primer S

MC-Top Primer STwo component primerfor Reparoxyd

Substrate PreparationThe cement based substrate must be at least 14days old, dry and free from anti-adhesive sub-stances (e.g. oil, fat, release agent, loose particlesetc.). At sub-zero temperatures the substrate mustbe defrosted and dried. Please refer to the datasheet „General Handling Information; Reparoxyd-Substrate preparation“.

MixingMix the liquid component, using a trowel or spatu-la, with the powder component to a homogenousmixture. Even for small quantities (e.g. approx.156 g liquid : 10 g powder) the mixing ratio of100 : 6 must be observed.

ApplicationThe cement based substrate is primed with MC-

Top Primer S using roller or brush. For best resultsReparoxyd should be applied after the primer hashardened, approx. after 1 - 2 hours.

Special InformationColour changes may appear during processingbecause of chemical impact and influence of light.It doesn’t affect the usability. Chemical andmechanical impact areas are affected by wear.Regularly monitoring and routine maintenance arerecommended.

Further InformationThe hazard warnings and the safety advice on thepackaging as well as the safety data sheet mustbe observed.

Product Properties

Areas of Application

• Primer for Reparoxyd-Systems for repair of small scale concrete areas • Assesed by REACH exposure scenarios: to be inhaled only periodically during application

• Two component• Based on special acrylate • Can be recoated immediately• Workable at temperatures below 0 °C

Application Notes

MC-Bauchemie • Am Kruppwald 1-8 • 46238 Bottrop • Tel. +49 (0) 20 41-101 50 • Fax: +49 (0) 20 41-101 [email protected] • www.mc-bauchemie.de

Page 2: MC-Top Primer S

Characteristic Unit Value Comments

Mixing Ratio 100 : 6 liquid : powder

Density g/cm³ approx. 0.98

Processing Time minutes approx. 7 at 20 °C

Consumption g/m² 250 - 300 cement based substrate

Processing conditions °C ≥ -10; ≤ 25 air and substrate temperature% ≤ 85 relative humidityK 3 above the dew point

Note: The information on this data sheet is based on our experiences and correct to the best of our knowledge. It is, however, not binding. It has tobe adjusted to the individual structure, application purpose and especially to local conditions. Our data refers to the accepted engineering rules,which have to be observed during application. This provided we are liable for the correctness of this data within the scope of our terms and conditi-ons of sale-delivery-and-service. Recommendations of our employees which differ from the data contained in our information sheets are only bindingif given in written form. The accepted engineering rules must be observed at all times.

Edition 06/13. Some technical changes have been made to this print medium. Older editions are invalid and may not be used anymore. If a techni-cally revised new edition is issued, this edition becomes invalid.

MC-Bauchemie • Am Kruppwald 1-8 • 46238 Bottrop • Tel. +49 (0) 20 41-101 50 • Fax: +49 (0) 20 41-101 [email protected] • www.mc-bauchemie.de

Technical Data for MC-Top Primer S

Product Characteristics for MC-Top Primer S

Equipment cleaning agent MC-Reinigungsmittel U

Standard colour transparent

Form of delivery Carton 6 x 1 kg

Storage Can be storaged for at least 6 months in closed packs under dryand frost free conditions.

Disposal To protect our environment please empty the packs completely.