Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
EVALUATION KIT AVAILABLEEVALUATION KIT AVAILABLE
General DescriptionThe MAX16826 high-brightness LED (HB LED) driver isdesigned for backlighting automotive LCD displays andother display applications such as industrial or desktopmonitors and LCD televisions. The MAX16826 integratesa switching regulator controller, a 4-channel linear cur-rent sink driver, an analog-to-digital converter (ADC),and an I2C interface. The IC is designed to withstandautomotive load dump transients up to 40V and canoperate under cold crank conditions.
The MAX16826 contains a current-mode PWM switchingregulator controller that regulates the output voltage tothe LED array. The switching regulator section is config-urable as a boost or SEPIC converter and its switchingfrequency is programmable from 100kHz to 1MHz.
The MAX16826 includes 4 channels of programmable,fault-protected, constant-current sink driver controllersthat are able to drive all white, RGB, or RGB plus amberLED configurations. LED dimming control for each chan-nel is implemented by direct PWM signals for each of thefour linear current sinks. An internal ADC measures thedrain voltage of the external driver transistors and theoutput of the switching regulator. These measurementsare then made available through the I2C interface to anexternal microcontroller (μC) to enable output voltageoptimization and fault monitoring of the LEDs.
The amplitude of the LED current in each linear current-sink channel and the switch-mode regulator output volt-age is programmed using the I2C interface. Additionalfeatures include: cycle-by-cycle current limit, shortedLED string protection, and overtemperature protection.The MAX16826 is available in a thermally enhanced,5mm x 5mm, 32-pin thin QFN package and is specifiedover the automotive -40°C to +125°C temperature range.
ApplicationsLCD Backlighting:
Automotive Infotainment Displays
Automotive Cluster Displays
Industrial and Desktop Monitors
LCD TVs
Automotive Lighting:
Adaptive Front Lighting
Low- and High-Beam Assemblies
Benefits and Features• 4 Channels of Programmable, Fault-Protected, Con-
stant-Current Source-Driver Controllers for All White,
RGB, or RGB Plus Amber LED Configurations
• Drives One to Four LED Strings
• Individual PWM Dimming Inputs per String
• Very Wide Dimming Range
• Configurable as a boost or SEPIC Converter with
Programmable 100kHz to 1MHz Switching Frequency
for Design Flexibility
• Integrated Boost/SEPIC Controller
• External MOSFETs Allow Wide-Range LED
Current with Multiple LEDs per String
• 200kHz to 2MHz Programmable Switching
Frequency for Optimizing Size vs. Efficiency
• External Switching-Frequency Synchronization
• I2C Allows the Current-Sink Drain Voltages to be
Read to Minimize Power Dissipation and Detect LED
String Fault Conditions
• 7-Bit Internal ADC for LED Voltage Monitoring and
Optimization
• Dynamic Adjustment of LED String Currents and
Output Voltage
• Standby Mode
• Protection Features Improve Reliability
• LED Short and Open Detection
• Overvoltage and Overtemperature Protection
Typical Application Circuit and Pin Configuration appear atend of data sheet.
Simplified Diagram
MAX16826
DR4
DR1
DL1
IN DL
BOOST LED DRIVER
CS FB
GND
VIN
DIM1DIM2
SDASCL
DIM3DIM4
I2CINTERFACE
DIMMINGINPUTS
CS1
DL4CS4
Ordering Information appears at end of data sheet.
19-4047; Rev 7; 2/16
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 2www.maximintegrated.com
Absolute Maximum Ratings
Electrical Characteristics(VIN = 12V, R19 = 2kΩ, C33 = 2200pF, R17 = 1.27kΩ, CDL_ = 0.01μF, TJ = -40°C to +125°C, unless otherwise noted. Typical valuesare at TA = +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functionaloperation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure toabsolute maximum rating conditions for extended periods may affect device reliability.
IN to GND (Continuous) .........................................-0.3V to +30VIN Peak Current (≤ 400ms) ...............................................300mAIN Continuous Current ........................................................50mAPGND to GND .......................................................-0.3V to +0.3VAll Other Pins to GND...............................................-0.3V to +6VDL Peak Current (< 100ns)....................................................±3ADL Continuous Current .....................................................±50mADL1, DL2, DL3, DL4 Peak Current ..................................±50mADL1, DL2, DL3, DL4 Continuous Current ........................±20mAVCC Continuous Current .....................................................50mA
All Other Pins Current .......................................................±20mAContinuous Power Dissipation (TA = +70°C)
32-Pin Thin QFN (derate 34.5mW/°C above +70°C)Multilayer Board ..........................................................2759mW
Operating Temperature Range .........................-40°C to +125°CJunction Temperature ......................................................+150°CStorage Temperature Range .............................-65°C to +150°CLead Temperature (soldering, 10s) ........…………………+300°CSoldering Temperature (reflow) .......................................+260°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Power-Supply Voltage VIN VSYNC = 3V 4.75 24 V
Quiescent Current IIN DL_ = unconnected; R19, C33 = open 5 10 mA
Shutdown Current IIN,SD VSYNC = 0V 20 75 μA
Standby Current IIN,SB I2C standby activated 3 mA
I2C-COMPATIBLE I/O (SCL, SDA)
Input High Voltage VIH 1.5 V
Input Low Voltage VIL 0.5 V
Input Hysteresis VHYS 25 mV
Input High Leakage Current IIH VLOGIC = 5V -1 +1 μA
Input Low Leakage Current IIL VLOGIC = 0V -1 +1 μA
Input Capacitance CIN 10 pF
Output Low Voltage VOL IOL = 3mA 0.4 V
Output High Current IOH VOH = 5V 1 μA
I2C-COMPATIBLE TIMING
Serial Clock (SCL) Frequency fSCL 400 kHz
BUS Free Time Between STOPand START Conditions
tBUF 1.3 μs
START Condition Hold Time tHD:STA 0.6 μs
STOP Condition Setup Time tSU:STO 0.6 μs
Clock Low Period tLOW 1.3 μs
Clock High Period tHIGH 0.6 μs
Data Setup Time tSU:DAT 0.3 μs
Data In Hold Time tHD:DATIN 0.03 0.9 μs
Data Out Hold Time tHD:DATOUT 0.3 μs
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 3www.maximintegrated.com
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Maximum Receive SCL/SDA RiseTime
tR CB = 400pF 300 ns
Minimum Receive SCL/SDA RiseTime
tR CB = 400pF 60 ns
Maximum Receive SCL/SDA FallTime
tF CB = 400pF 300 ns
Minimum Receive SCL/SDA FallTime
tF CB = 400pF 60 ns
Transmit SDA Fall Time tF CB = 400pF, IO = 3mA 60 250 ns
Pulse Width of Suppressed Spike tSP 50 ns
INTERNAL REGULATORS (IN, VCC)
VCC Output Voltage VVCC
0V < IVCC < 30mA (Note 2),4.75V < VIN < 24V, DL, DL1 to DL4unconnected
4.5 5.25 5.65 V
VCC Undervoltage Lockout VVCC_UVLO VCC rising 4.5 V
VCC Undervoltage LockoutHysteresis
VVCC_HYS 135 175 205 mV
IN Shunt Regulation Voltage IIN = 250mA 24.05 26.0 27.5 V
PWM GATE DRIVER (DL)
Peak Source Current 2 A
Peak Sink Current 2 A
DL High-Side Driver Resistance IDL = -100mA 2.25 ΩDL Low-Side Driver Resistance IDL = +100mA 1.30 ΩMinimum DL Pulse Width 40 ns
PWM CONTROLLER, SOFT-START (FB, COMP, OVP)
FB shorted to COMP; MAX16826 only 1.230 1.250 1.260FB Voltage Maximum VFB,MAX
FB shorted to COMP; MAX16826B only 1.23 1.25 1.27V
FB shorted to COMP; MAX16826 only 862 876 885FB Voltage Minimum VFB,MIN
FB shorted to COMP; MAX16826B only 735 750 765mV
FB shorted to COMP; MAX16826 only 2.94FB Voltage LSB
FB shorted to COMP; MAX16826B only 3.9mV
FB Input Bias Current IFB 0V < VFB < 5.5V -100 0 +100 nA
Feedback-Voltage LineRegulation
Level to produce VCOMP = 1.25V,4.5V < VVCC < 5.5V
±0.25 %/V
Soft-Start Current ISS VCSS = 0.5VVCC 3.2 6.0 10.4 μA
OVP Input Bias Current IOVP 0V < VOVP < 5.5V -100 0 +100 nA
Slope Compensation ISLOPE 19 26 32 μA/μs
Electrical Characteristics (continued)(VIN = 12V, R19 = 2kΩ, C33 = 2200pF, R17 = 1.27kΩ, CDL_ = 0.01μF, TJ = -40°C to +125°C, unless otherwise noted. Typical valuesare at TA = +25°C.) (Note 1)
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 4www.maximintegrated.com
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
ERROR AMPLIFIER (FB, COMP)
Open-Loop Gain AOL 80 dB
Unity-Gain Bandwidth BW 2 MHz
Phase Margin PM 65 Degrees
Sourcing, VCOMP = 3V 1.9Error-Amplifier Output Current ICOMP
Sinking, VCOMP = 2V 0.9mA
COMP Clamp Voltage VCOMP VFB = 0V 3.25 4.5 V
COMP Short-Circuit Current ICOMP_SC 12 mA
PWM CURRENT LIMIT (CS)
Cycle-by-Cycle Current-LimitThreshold
VCL VDL = 0V 187 200 217 mV
Cycle-by-Cycle Current-LimitPropagation Time To DL
tPROP, CL 10mV overdrive 80 ns
Gross Current-Limit Threshold VGCL VCSS = 0V 250 270 280 mV
Gross Current-Limit PropagationTime To DL
tPROP,GCL 10mV overdrive 80 ns
Input Bias Current 0V < VCS < 5.5V -100 0 +100 nA
PWM OSCILLATOR (RTCT)
RTCT Voltage Ramp (Peak toPeak)
VRAMP 5.5V < VIN < 24V 1.60 1.65 1.80 V
RTCT Voltage Ramp Valley VRAMP_VALLEY 5.5V < VIN < 24V 1.11 1.20 1.27 V
Discharge Current IDIS VRTCT = 2V 7.8 8.4 9.1 mA
Frequency Range fOSC 5.5V < VIN < 24V 100 1000 kHz
SYNCHRONIZATION (SYNC/ENABLE)
Input Rise/Fall Time 200 ns
Input Frequency Range 100 1000 kHz
Input High Voltage 1.5 V
Input Low Voltage 0.5 V
Input Minimum Pulse Width 200 ns
Input Bias Current 0V < VSYNC < 5.5V -100 0 +100 nA
Delay to Shutdown VSYNC = 0V 13 32 65 μs
LED DIMMING (DIM1–DIM4)
Input High Voltage VDIM,MAX 1.5 V
Input Low Voltage VDIM,MIN 0.5 V
Minimum Dimming Frequency fDIM tON = 2μs (Note 3) 45 Hz
Input Bias Current IDIM 0V < VDIM_ < 5.5V -100 0 +100 nA
Electrical Characteristics (continued)(VIN = 12V, R19 = 2kΩ, C33 = 2200pF, R17 = 1.27kΩ, CDL_ = 0.01μF, TJ = -40°C to +125°C, unless otherwise noted. Typical valuesare at TA = +25°C.) (Note 1)
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 5www.maximintegrated.com
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
ADC (DR1–DR4, OVP)
Maximum Error EMAX ±50 mV
ADC Single Bit AcquisitionLatency
(Note 4) 2 μs
DR Channel Sample Time tDR,SMPL 190 ms
OVP Channel Sample Time tOVP,SMPL 20 μs
Full-Scale Input Voltage VFS 1.215 1.24 1.2550 V
Least Significant Bit VLSB 9.76 mV
DR Input Bias Current IDR 0V < VDR_ < 5.5V -100 0 +100 nA
DRAIN FAULT COMPARATORS (DR1–DR4) (Shorted LED String Comparator)
Drain Fault ComparatorThreshold
VDFTH Voltage to drive DL1–DL4 low 1.4 1.52 1.63 V
Drain Fault Comparator Delay tDFD 10mV overdrive 1 μs
LINEAR REGULATORS (DL1–DL4, CS1–CS4)
Transconductance Gm ΔI = -500μA 75 mS
Maximum Output Current IDL Sourcing or sinking 15 mA
CS1–CS4 Input Bias Current ICS 0V < VCS < 5.5V -100 0 +100 nA
CS_ = DL_, FB DAC full scale;MAX16826 only
306 316 324CS1–CS4 Regulation VoltageMaximum
VCS,MAXCS_ = DL_, FB DAC full scale;MAX16826B only
308 318 328
mV
CS_ = DL_, FB DAC minus full scale;MAX16826 only
90 97 105CS1–CS4 Regulation VoltageMinimum
VCS,MINCS_ = DL_, FB DAC minus full scale;MAX16826B only
90 99 109
mV
CS1–CS4 Regulation Voltage LSB VCS,LSB CS_ = DL_, FB DAC 1-bit transition 1.72 mV
Electrical Characteristics (continued)(VIN = 12V, R19 = 2kΩ, C33 = 2200pF, R17 = 1.27kΩ, CDL_ = 0.01μF, TJ = -40°C to +125°C, unless otherwise noted. Typical valuesare at TA = +25°C.) (Note 1)
Note 1: All devices are 100% production tested at TJ = +25°C and TJ = +125°C. Limits to -40°C are guaranteed by design.Note 2: ICC includes the internal bias currents and the current used by the gate drivers to drive DL, DL1, DL2, DL3, and DL4.Note 3: Minimum frequency to allow the internal ADC to complete at least one measurement. tON is the on-time with the LED current
in regulation.Note 4: Minimum LED current pulse duration, which is required to correctly acquire 1 bit.
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 6www.maximintegrated.com
SUPPLY CURRENTvs. SUPPLY VOLTAGE
MAX
1682
6 to
c01
SUPPLY VOLTAGE (V)
SUPP
LY C
URRE
NT (m
A)
20164 8 12
2
4
6
8
10
12
14
16
00 24
CDL = 4700pF
SUPPLY CURRENTvs. OSCILLATOR FREQUENCY
MAX
1682
6 to
c02
OSCILLATOR FREQUENCY (kHz)
SUPP
LY C
URRE
NT (m
A)
900800700600500400300200
10
20
30
40
0100 1000
CDL = 4700pFC33 FROM 680pF TO 8200pF
SUPPLY CURRENTvs. TEMPERATURE
MAX
1682
6 to
c03
TEMPERATURE (°C)
SUPP
LY C
URRE
NT (m
A)
11085603510-15
13
14
15
16
17
12-40
CDL = 4700pF
OSCILLATOR FREQUENCYvs. SUPPLY VOLTAGE
MAX
1682
6 to
c04
SUPPLY VOLTAGE (V)
OSCI
LLAT
OR F
REQU
ENCY
(kHz
)
20.316.612.99.2
310
320
330
340
350
360
3005.5 24.0
OSCILLATOR FREQUENCYvs. TEMPERATURE
MAX
1682
6 to
c05
TEMPERATURE (°C)
OSCI
LLAT
OR F
REQU
ENCY
(kHz
)
11085603510-15
240
280
320
360
400
200-40
LED OUTPUT CURRENTvs. TEMPERATURE
MAX
1682
6 to
c06
TEMPERATURE (°C)
LED
OUTP
UT C
URRE
NT (m
A)
80604020
137
139
141
143
145
1350 100
VCS = 0.32V
Typical Operating Characteristics(VIN = 12V, R19 = 2kΩ, C33 = 2200pF, R17 = 1.27kΩ, CDL_ = 0.01μF. TA = +25°C, unless otherwise noted.)
LED OUTPUT CURRENTvs. INPUT VOLTAGE
MAX
1682
6 to
c07
INPUT VOLTAGE (V)
LED
OUTP
UT C
URRE
NT (m
A)
18126
30
60
90
120
150
00 24
DIM INPUT TO ILED OUTPUT WAVEFORMMAX16826 toc08
2μs/div
5V/div
100mA/div
0mA
0VVDIM
ILED
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 7www.maximintegrated.com
ENABLE AND DISABLE RESPONSEMAX16826 toc09
40ms/div
5V/div
100mA/div
0mA
0VVSYNC/EN
ILED
VCC VOLTAGEvs. LOAD CURRENT
MAX
1682
6 to
c10
LOAD CURRENT (mA)
V CC
VOLT
AGE
(V)
40302010
5.1
5.2
5.3
5.4
5.5
5.00 50
VCC VOLTAGEvs. TEMPERATURE
MAX
1682
6 to
c11
TEMPERATURE (°C)
V CC
VOLT
AGE
(V)
80604020
5.1
5.2
5.3
5.4
5.5
5.00 100
Typical Operating Characteristics (continued)(VIN = 12V, R19 = 2kΩ, C33 = 2200pF, R17 = 1.27kΩ, CDL_ = 0.01μF. TA = +25°C, unless otherwise noted.)
VCC VOLTAGEvs. SUPPLY VOLTAGE
MAX
1682
6 to
c12
SUPPLY VOLTAGE (V)
V CC
VOLT
AGE
(V)
20161284
1
2
3
4
5
6
00 24
SHUNT VOLTAGEvs. SHUNT CURRENT
MAX
1682
6 to
c13
SHUNT CURRENT (mA)
SHUN
T VO
LTAG
E (V
)
20015010050
24.5
25.0
25.5
26.0
26.5
27.0
24.00 250
SHUNT VOLTAGEvs. TEMPERATURE
MAX
1682
6 to
c14
TEMPERATURE (°C)
SHUN
T VO
LTAG
E (V
)
11085603510-15
23
24
25
26
27
28
22-40
SHUNT REGULATOR LOAD DUMP RESPONSEMAX16826 toc15
200ms/div
20V/div
10V/div
0V
0V
VSUPPLY
VSHUNT
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 8www.maximintegrated.com
Pin Description
PIN NAME FUNCTION
1 PGND Power Ground
2, 3 GND Analog Ground
4 RTCTTiming Resistor and Capacitor Connection. A resistor, R19 (in the Typical Application Circuit), from VCC toRTCT and a capacitor C33, from RTCT to GND set the oscillator frequency. See the Oscillator section tocalculate RT and CT component values.
5 SYNC/EN
Synchronization and Enable Input. There are three operating modes: SYNC/EN = LOW: Low current shutdown mode with all circuits shut down except shunt regulator. SYNC/EN = HIGH: All circuits active with oscillator frequency set by RTCT network. SYNC/EN = CLOCKED: All circuits active with oscillator frequency set by SYNC clock input. Conversion cycles initiate on the rising edge of external clock input. The frequency programmed by R19/C33 must be 10% lower than the input SYNC/EN signal frequency.
6 CSSSoft-Start Timing Capacitor Connection. Connect a capacitor from CSS to GND to program the required soft-start time for the switching regulator output voltage to reach regulation. See the Soft-Start (CSS) section tocalculate CCSS.
7 COMPSwitching Regulator Compensation Component Connection. Connect the compensation network betweenCOMP and FB.
8 FBSwitching Regulator Feedback Input. Connect FB to the center of a resistor-divider connected between theswitching regulator output and GND to set the output voltage. FB is regulated to a voltage set by an internalregister. See the Setting Output Voltage section for calculating resistor values.
9 OVP
Switching Regulator Overvoltage Input. Connect OVP to the center of a resistor-divider connected between theswitching regulator output and GND. For normal operation, configure the resistor-divider so that the voltage atthis pin does not exceed 1.25V. If operation under load dump conditions is also required, configure the resistor-divider so that the voltage at OVP is less than 1.25V.
10 RSCSlope Compensation Resistor and PWM Comparator Input Connection. Connect a resistor, R17, from RSC tothe switching current-sense resistor to set the amount of the compensation ramp. See the Slope Compensation(RSC) section for calculating the value.
11 SDA I2C Serial Data Input/Output
12 SCL I2C Serial Clock Input
13 DIM1LED String 1 Logic-Level PWM Dimming Input. A high logic level on DIM1 enables the current sink to operate atthe maximum current as determined by its sense resistor and internal register value. A low logic level disablesthe current source.
14 DIM2LED String 2 Logic-Level PWM Dimming Input. A high logic level on DIM2 enables the current sink to operate atthe maximum current as determined by its sense resistor and internal register value. A low logic level disablesthe current source.
15 DIM3LED String 3 Logic-Level PWM Dimming Input. A high logic level on DIM3 enables the current sink to operate atthe maximum current as determined by its sense resistor and internal register value. A low logic level disablesthe current source.
16 DIM4LED String 4 Logic-Level PWM Dimming Input. A high logic level on DIM4 enables the current sink to operate atthe maximum current as determined by its sense resistor and internal register value. A low logic level disablesthe current source.
17 CS1LED String 1 Current-Sense Input. CS1 is regulated to a value set by an internal register. The regulation voltagecan be set between 97mV and 316mV.
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 9www.maximintegrated.com
Pin Description (continued)
PIN NAME FUNCTION
18 DL1LED String 1 Linear Current Source Output. DL1 drives the gate of the external FET on LED String 1 and hasapproximately 15mA source/sink capability. Connect a minimum capacitor of 4700pF from DL1 to GND tocompensate the internal transconductance amplifier as well as program the rise and fall times of the LED currents.
19 DR1LED String 1 External FET Drain Voltage Sense. The internal ADC uses this input to measure the drain to GNDvoltage of the current sink FET. Drain voltage measurement information can be read back from the I2Cinterface. Connect a voltage-divider to scale drain voltage as necessary.
20 CS2LED String 2 Current-Sense Input. CS2 is regulated to a value set by an internal register. The regulation voltagecan be set between 97mV and 316mV.
21 DL2
LED String 2 Linear Current Source Output. DL2 drives the gate of the external FET on LED String 2 and hasapproximately 15mA source/sink capability. Connect a minimum capacitor of 4700pF from DL2 to GND tocompensate the internal transconductance amplifier, as well as program the rise and fall times of the LEDcurrents.
22 DR2LED String 2 External FET Drain Voltage Sense. The internal ADC uses this input to measure the drain to GNDvoltage of the current sink FET. Drain voltage measurement information can be read back from the I2Cinterface. Connect a voltage-divider to scale drain voltage as necessary.
23 CS3LED String 3 Current-Sense Input. CS3 is regulated to a value set by an internal register. The regulation voltagecan be set between 97mV and 316mV.
24 DL3LED String 3 Linear Current Source Output. DL3 drives the gate of the external FET on LED String 3 and hasapproximately 15mA source/sink capability. Connect a minimum capacitor of 4700pF from DL3 to GND tocompensate the internal transconductance amplifier, as well as program the rise and fall times of the LED currents.
25 DR3LED String 3 External FET Drain Voltage Sense. The internal ADC uses this input to measure the drain to GNDvoltage of the current sink FET. Drain voltage measurement information can be read back from the I2Cinterface. Connect a voltage-divider to scale drain voltage as necessary.
26 CS4LED String 4 Current-Sense Input. CS4 is regulated to a value set by an internal register. The regulation voltagecan be set between 97mV and 316mV.
27 DL4LED String 4 Linear Current Source Output. DL3 drives the gate of the external FET on LED String 4 and hasapproximately 15mA source/sink capability. Connect a minimum capacitor of 4700pF from DL4 to GND tocompensate the internal transconductance amplifier, as well as program the rise and fall times of the LED currents.
28 DR4LED String 4 External FET Drain Voltage Sense. The internal ADC uses this input to measure the drain to GNDvoltage of the current sink FET. Drain voltage measurement information can be read back from the I2Cinterface. Connect a voltage-divider to scale drain voltage as necessary.
29 INPower Supply. IN is internally connected to a 26V shunt regulator that sinks current. In conjunction with anexternal resistor it allows time-limited load dump events as high as 40V to be safely handled by the IC. BypassIN to GND with a minimum 10μF capacitor.
30 CS Current-Sense Input
31 VCC
Gate Driver Regulator Output. Bypass VCC to GND with a minimum 4.7μF ceramic capacitor. Gate drive currentpulses come from the capacitor connected to VCC. Place the capacitor as close as possible to VCC. If IN ispowered by a voltage less than 5.5V, connect VCC directly to IN.
32 DL Switching Regulator Gate Driver Output
— EPExposed Pad. Connect the exposed pad to the ground plane for heatsinking. Do not use this pad as the onlyground connection to the IC.
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 10www.maximintegrated.com
Detailed DescriptionThe MAX16826 HB LED driver integrates a switchingregulator controller, a 4-channel linear current sink dri-ver, a 7-bit ADC, and an I2C interface. The IC isdesigned to operate from a 4.75V to 24V input voltagerange and can withstand automotive load dump tran-sients up to 40V.
The current-mode switching regulator controller is con-figurable as a boost or SEPIC converter to regulate thevoltage to drive the four strings of HB LEDs. Its program-mable switching frequency (100kHz to 1MHz) allows the
use of a small inductor and filter capacitors. The fourcurrent sink regulators use independent external current-sense resistors to provide constant currents for eachstring of LEDs. Four DIM inputs allow a very wide rangeof independent pulsed dimming to each LED string. Aninternal 7-bit ADC measures the drain voltage of theexternal driver transistors to enable output voltage opti-mization and fault monitoring of the LEDs. TheMAX16826 is capable of driving four strings of LEDs.The number of LEDs in each string is only limited by thetopology of choice, the rating of the external compo-nents, and the resolution of the ADC and internal DAC.
Simplified Block Diagram
31
IN
5V
VCC
VCC
PGND
DL
CS
OVP
COMP
FB
RTCT
GND
OVT
CURRENT-MODEPWM
BLOCK
SYNC/EN
CSS
DR47-BIT ADCAND
SHORTEDSTRINGFAULT
DECTECTION
DR3
DR2
DR1
LINEARCURRENT-
SINKDRIVERS
CS4
CS3
CS2
CS1
DL4
DL3
DL2
DL1
I2CSTATE
MACHINE
DOUBLE-BUFFEREDREGISTERAND DACS
DIM4
DIM3
OVTOVT
DIM2
DIM1
SDA
SCL
26VSHUNT
GND
OVT
REF
VCC
GND
RSC
MAX16826
29
28
25
22
19
26
23
20
17
27
24
21
18
16
15
14
13
9
32
1
30
8
10
6
7
4
5
2
3
11
12
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 11www.maximintegrated.com
The MAX16826 provides additional flexibility with aninternal I2C serial interface to communicate with amicrocontroller (μC). The interface can be used todynamically adjust the amplitude of the LED current ineach LED string and the switch-mode regulator outputvoltage. It can also be used to read the ADC drain volt-age measurements for each string, allowing a μC todynamically adjust the output voltage to minimize thepower dissipation in the LED current sink FETs. The I2Cinterface can also be used to detect faults such as LEDshort or open.
Modes of OperationThe MAX16826 has six modes of operation: normalmode, undervoltage lockout (UVLO) mode, thermalshutdown (TSD) mode, shutdown (SHDN) mode,standby (STBY) mode, and overvoltage protection(OVP) mode.
The normal mode is the default state where each cur-rent sink regulator is maintaining a constant currentthrough each of the LED strings. Digitized voltage feed-back from the drains of the current sink FETs can beused to establish a secondary control loop by using anexternal μC to control the output of the switching stagefor the purpose of achieving low-power dissipationacross these FETs.
UVLO mode occurs when VVCC goes below 4.3V. InUVLO mode, each of the linear current sinks and theswitching regulator is shut down until the input voltageexceeds the rising UVLO threshold.
TSD mode occurs when the die temperature exceedsthe internally set thermal limit (+160°C). In TSD mode,each of the linear regulators and the switching regulatoris shut down until the die temperature cools by 20°C.
SHDN mode occurs when SYNC/EN is driven low. InSHDN mode, all internal circuitry with the exception ofthe shunt regulator is deactivated to limit current drawto less than 50μA. SHDN mode disengages whenSYNC/EN is driven high or clocked.
STBY mode is initiated using the I2C interface. In STBYmode, each of the linear current sinks and the switchingregulator is shut down. STBY mode is also deactivatedusing the I2C interface. In STBY mode, the internal VCCregulator and the shunt regulator remain active. Whenever
the MAX16826 enters a mode that deactivates the switch-ing regulator, the soft-start capacitor is discharged so thatsoft-start occurs upon reactivation.
OVP mode occurs when the voltage at OVP is higher thanthe internal reference. In OVP mode, the switching regula-tor gate-drive output is latched off and can only berestored by cycling enable, power, or entering standbymode.
Switching Preregulator StageThe MAX16826 features a current-mode controller thatis capable of operating in the frequency range of100kHz to 1MHz. Current-mode control provides fastresponse and simplifies loop compensation.
Output voltage regulation can be achieved in a two-loop configuration. A required conventional control loopcan be set up by using the internal error amplifier withits inverting input connected to FB. The bandwidth ofthis loop is set to be as high as possible utilizing con-ventional compensation techniques. The noninvertinginput of this amplifier is connected to a reference volt-age that is dynamically adjustable using the I2C inter-face. The optional slower secondary loop consists ofthe external μC using the I2C interface reading out thevoltages at the drains of the current sink FETs andadjusting the reference voltage for the error amplifier.
To regulate the output voltage, the error amplifier com-pares the voltage at FB to the internal 1.25V (adjustabledown by using the I2C interface) reference. The outputof the error amplifier is compared to the sum of the cur-rent-sense signal and the slope compensation ramp atRSC to control the duty cycle at DL.
Two current-limit comparators also monitor the voltageacross the sense resistor using CS. If the primary cur-rent-limit threshold is reached, the FET is turned off andremains off for the reminder of the switching cycle. Ifthe current through the FET reaches the secondary cur-rent limit, the switching cycle is terminated and the soft-start capacitor is discharged. The converter thenrestarts in soft-start mode preventing inductor currentrunaway due to the delay of the primary cycle-by-cyclecurrent limit. The switching regulator controller also fea-tures an overvoltage protection circuit that latches thegate driver off if the voltage at OVP exceeds the inter-nal 1.25V reference voltage.
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 12www.maximintegrated.com
Shunt RegulatorThe MAX16826 has an internal 26V (typ) shunt regula-tor to provide the primary protection against an auto-motive load dump. When the input voltage is below26V, the shunt voltage at IN tracks the input voltage.When the input voltage exceeds 26V, the shunt regula-tor turns on to sink current, and the voltage at IN isclamped to 26V. During a load dump, the input voltagecan reach 40V, and the shunt regulator through theresistor connected to IN is forced to sink large amountsof current for up to 400ms to limit the voltage thatappears at IN to the shunt regulation voltage. The sink-ing current of the shunt regulator is limited by the valueof resistor (R1 in Figure 1) in series with IN. There aretwo criteria that determine the value of R1: the maxi-mum acceptable shunt current during load dump, andthe voltage drop on R1 under normal operating condi-tions with low battery voltage. For example, with typical20mA input current in normal operation, 250mA loaddump current limit, 40V maximum load dump voltage,the R1 value is:
where VINMIN is the minimum operating voltage andVINREG is the minimum acceptable voltage at IN.
Use the following equation to verify that the currentthrough R1 is less than 250mA under a load-dump con-dition:
For stable operation, the shunt regulator requires a min-imum 10μF of ceramic capacitance from IN to GND.
VCC RegulatorThe 5.25V VCC regulator provides bias for the internalcircuitry including the bandgap reference and gate dri-vers. Externally bypass VCC with a minimum 4.7μFceramic capacitor. VCC has the ability to supply up to50mA of current, but external loads should be mini-mized so as not to take away drive capability for inter-nal circuitry. If IN is powered by a voltage less than5.5V, connect VCC directly to IN.
Switch-Mode ControllerThe MAX16826 consists of a current-mode controllerthat is capable of operating in the 100kHz to 1MHz fre-quency range (Figure 2). Current-mode control pro-vides fast response and simplifies loop compensation.The error amplifier compares the voltage at FB to 1.25Vand varies the COMP output accordingly to regulate.The PWM comparator compares the voltage at COMPwith the voltage at RSC to determine the switching dutycycle. The primary cycle-by-cycle current-limit com-parator interrupts the on-time if the sense voltage islarger than 200mV. When the sense voltage is largerthan 270mV, the secondary gross current-limit com-parator is activated to discharge the soft-start capaci-tor. This forces the IC to re-soft-start preventinginductor current runaway due to the delay of the prima-ry cycle-by-cycle current limit.
The switch-mode controller also features a low currentshutdown mode, adjustable soft-start, and thermalshutdown protection.
IV V
RmALD
LD= = =− −261
40 26100
140
RV V
IINMIN INREG
Q1
7 5 5 5
20 10100
3= =
×=− −
−
. . Ω
MAX16826
VININ
R1
C4
5V REFERENCE
Figure 1. Shunt Regulator Block Diagram
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 13www.maximintegrated.com
OVP
CSS
FB
SWR DACI2C BUS
Q
QSET
CLR
S
R
Q
Q
SET
CLR
S
R
6µA
1.25V
COMP
SHDN
STBY
OSCILLATOR
26µA/µs
SYNC
RTCT
RSC
SOFT-START COMPARATOR
OVP COMPARATOR
ERROR AMPLIFIER
PWM COMPARATOR
DL
CS
270mV
200mV
VCC
10µA
MAX16826
CURRENT-RAMP
GENERATOR
VCC
CURRENT-LIMITCOMPARATORS
-
-
+
+
-
+
-
+
-
+
-
+
ANALOGMUX
Figure 2. Switch Regulator Controller Block Diagram
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 14www.maximintegrated.com
OscillatorThe MAX16826 oscillator frequency is programmableusing an external capacitor (C33 in the TypicalApplication Circuit) and a resistor (R19) at RTCT. R19 isconnected from RTCT to VCC and C33 is connectedfrom RTCT to GND. C33 charges through RT until VRTCTreaches 2.85V. CT then discharges through an 8.4mAinternal current sink until VRTCT drops to 1.2V. C33 isthen allowed to charge through R19 again. The periodof the oscillator is the sum of the charge and dischargetimes of C3. Calculate these times as follows:
The charge time is:
tC = 0.55 x R19 x C33
The discharge time is:
where tC and tD is in seconds, R19 is in ohms (Ω), andC33 is in farads (F).
The oscillator frequency is then:
The charge time (tC) in relation to the period (tC + tD)sets the maximum duty cycle of the switching regulator.Therefore, the charge time (tC) is constrained by thedesired maximum duty cycle. Typically, the duty cycleshould be limited to 95%. The oscillator frequency isprogrammable from 100kHz to 1MHz. The MAX16826can be synchronized to an external oscillator throughSYNC/EN.
Slope Compensation (RSC)The MAX16826 uses an internal ramp generator forslope compensation to stabilize the current loop whenthe duty cycle exceeds 50%. A slope compensationresistor (R17 in the Typical Application Circuit) is con-nected between RSC and the switching current-senseresistor at the source of the external switching FET.When the voltage at DL transitions from low to high, aramped current with a slope of 26μA/μs is generatedand flows through the slope compensation resistor. It iseffectively summed with the current-sense signal. Whenthe voltage at DL is low, the current ramp is reset to 0.Calculate R17 as follows:
where VOUT is the switching regulator output and VINMIN is the minimum operating input voltage.
Current Limit (CS)The MAX16826 includes a primary cycle-by-cycle, cur-rent-limit comparator and a secondary gross current-limit comparator to terminate the on-time or switchcycle during an overload or fault condition. The current-sense resistor (R12 in the Typical Application Circuit)connected between the source of the switching FETand GND and the internal threshold, set the currentlimit. The current-sense input (CS) has a voltage triplevel (VCS) of 200mV. Use the following equation to cal-culate R39:
R12 = VCS/IPK
where IPK is the peak current that flows through theswitching FET. When the voltage across R12 exceedsthe current-limit comparator threshold, the FET driver(DL) turns the switch off within 80ns. In some cases, asmall RC filter may be required to filter out the leading-edge spike on the sensed waveform. Set the time con-stant of the RC filter at approximately 100ns and adjustas needed.
If, for any reason, the voltage at CS exceeds the 270mVtrip level of the gross current limit as set by a secondcomparator, then the switching cycle is immediatelyterminated and the soft-start capacitor is discharged.This allows a new soft-start cycle and prevents inductorcurrent buildup.
Soft-Start (CSS)Soft-start is achieved by charging the external soft-startcapacitor (C30 in the Typical Application Circuit) atstartup. An internal fixed 6μA current source chargesthe soft-start capacitor until VCSS reaches VCC. Toachieve the required soft-start timing for the switchingregulator output voltage to reach regulation, the valueof the soft-start capacitor at CSS is calculated as:
C30 = 6μA x tSS/VREF
where tSS is the required time to achieve the switchingregulator output regulation and VREF is the set FB regu-lation voltage. When the IC is disabled, the soft-startcapacitor is discharged to GND.
Synchronization and Enable InputThe SYNC/EN input provides both external clock syn-chronization (if desired) and enable control. WhenSYNC/EN is held low, all circuits are disabled and theIC enters low-current shutdown mode. When SYNC/ENis high, the IC is enabled and the switching regulatorclock uses the RTCT network to set the operating fre-quency. See the Oscillator section for details. TheSYNC/EN can also be used for frequency synchroniza-tion by connecting it to an external clock signal from100kHz to 1MHz. The switching cycle initiates on the
RV V R
LOUT INMIN17
1234 28 1
= ××
−( ).
ft tOSCC D
=+1
t R C R RD = × × ( )− −ln . .19 33 19 281 86 19 487 445( )( )
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 15www.maximintegrated.com
rising edge of the clock. When using external synchro-nization, the clock frequency set by RTCT must be 10%lower than the synchronization signal frequency.
Overvoltage Protection (OVP)OVP limits the maximum voltage of the switching regu-lator output for protection against overvoltage due tocircuit faults, for example a disconnected FB. ConnectOVP to the center of a resistor-divider connectedbetween the switching regulator output and GND to setthe output-voltage OVP limit. Typically, the OVP outputvoltage limit is set higher than the load dump voltage.Calculate the value of R15 and R16 as follows:
R15 = (VOVP/1.25 - 1) x R16
Or to calculate VOVP:
VOVP = 1.25 x (1 + R15/R16)
where R15 and R16 are shown in the Typical ApplicationCircuit. The internal OVP comparator compares the volt-age at OVP with the internal reference (1.25V typ) todecide if an overvoltage error occurs. If an overvoltageerror is detected, switching stops, the switching regula-tor gate-drive output is latched off, and the soft-startcapacitor is discharged. The latch can only be reset bytoggling SYNC/EN, activating the I2C standby mode, orcycling power. The internal ADC also uses OVP to sense the switchingregulator output voltage. Output voltage measurementinformation can be read back from the I2C interface.Voltage is digitized to 7-bit resolution.
Undervoltage Lockout (UVLO)When the voltage at VCC is below the VCC undervolt-age threshold (VVCC_UVLO, typically 4.3V falling), theMAX16826 enters undervoltage lockout. VCC UVLOforces the linear regulators and the switching regulatorinto shutdown mode until the VCC voltage is highenough to allow the device to operate normally. In VCCUVLO, the VCC regulator remains active.
Thermal ShutdownThe MAX16826 contains an internal temperature sensorthat turns off all outputs when the die temperatureexceeds +160°C. The outputs are enabled again whenthe die temperature drops below +140°C. In thermalshutdown, all internal circuitry is shut down with theexception of the shunt regulator.
Linear Current Sources (CS1–CS4, DL1–DL4)The MAX16826 uses transconductance amplifiers to con-trol each LED current sink. The amplifier outputs(DL1–DL4) drive the gates of the external current sink FETs
(Q2 to Q5 in the Typical Application Circuit). The source ofeach MOSFET is connected to GND through a current-sense resistor. CS1–CS4 are connected to the respectiveinverting input of the amplifiers and also to the source ofthe external current sink FETs where the LED string cur-rent-sense resistors are connected. The noninverting inputof each amplifier is connected to the output of an internalDAC. The DAC output is programmable using the I2C inter-face to output between 97mV and 316mV. The regulatedstring currents are set by the value of the current-senseresistors (R28 to R31 in the Typical Application Circuit) andthe corresponding DAC output voltages.
LED PWM Dimming (DIM1–DIM4)The MAX16826 features a versatile dimming scheme forcontrolling the brightness of the four LED strings.Independent LED string dimming is accomplished by dri-ving the appropriate DIM1–DIM4 inputs with a PWM sig-nal with a frequency up to 100kHz. Although thebrightness of the corresponding LED string is proportionalto the duty cycle of its respective PWM dimming signal,finite LED current rise and fall times limit this linearitywhen the dim pulse width approaches 2μs. Each LEDstring can be independently controlled. Simultaneouscontrol of the PWM dimming and the LED string currentsin an analog way over a 3:1 range provides great flexibili-ty allowing independent two-dimensional brightness con-trol that can be used for color point setup and brightnesscontrol.
Analog-to-Digital Converter (ADC)The MAX16826 has an internal ADC that measures thedrain voltage of the external current sink driver FETs(Q2 to Q5 in the Typical Application Circuit) using DR1 - DR4 and the switching regulator output voltageusing OVP. Fault monitoring and switching stage out-put-voltage optimization is possible by using an exter-nal microcontroller to read out these digitized voltagesthrough the I2C interface. The ADC is a 7-bit SAR (suc-cessive-approximation register) topology. It sequential-ly samples and converts the drain voltage of eachchannel and VOVP. An internal 5-channel analog MUXis used to select the channel the ADC is sampling.Conversions are driven by an internally generated1MHz clock and gated by the external dimming sig-nals. After a conversion, each measurement is storedinto its respective register and can be accessedthrough the I2C interface. The digital circuitry that con-trols the analog MUX includes a 190ms timer. If theADC does not complete a conversion within this 190msmeasurement window then the analog MUX wil lsequence to the next channel. For the ADC to completeone full conversion, the cumulative PWM dimming on-time must be greater than 10μs within the 190ms mea-surement window. The minimum PWM dimming on-time
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 16www.maximintegrated.com
is 2μs, so the ADC requires at least 5 of these minimumpulses within the 190ms measurement window to com-plete a conversion. During PWM dimming, LED currentpulse widths of less than 2μs are possible, but the ADCmay not have enough sampling time to complete a con-version in this scenario and the corresponding data maybe incomplete or inaccurate. Therefore, adaptive volt-age optimization may not be possible when the LEDcurrent-pulse duration is less than 2μs. The LED currentpulse duration is shorter than the pulse applied at theDIM_ inputs because of the LED turn-on delay.
Faults and Fault DetectionThe MAX16826 features circuitry that automaticallydetects faults such as overvoltage or shorted LED string.An internal fault register at the address OAh is used torecord these faults. For example, if a shorted LED stringis detected, the corresponding fault register bit is set andthe faulty output is shut down.
Shorted LED strings are detected with fast comparatorsconnected to DR1–DR4. The trip threshold of thesecomparators is 1.52V (typ). When this threshold is
exceeded, the shorted string is latched off and the cor-responding bit of register OAh is set.
After the internal ADC completes a conversion, theresult is stored in the corresponding register and canbe read out by the external μC. The μC then comparesthe conversion data with the preset limit to determine ifthere is a fault.
When an LED string opens, the voltage at the corre-sponding current-sink FET drain node goes to 0V.However, the ADC can only complete a conversion ifthe LED current comes into regulation. If an LED stringopens before the LED current can come into regulation,the ADC cannot complete a conversion and the MSB(eighth bit) is set to indicate an incomplete conversionor timeout condition. Thus, an examination of the MSBprovides an indication that the LED string is open. If theLED string opens after the LED current is in regulation,the ADC can make conversions and reports that thedrain voltage is 0V. Therefore, to detect an open condi-tion, monitor the MSB and the ADC measurement. If theMSB is set and the CS_ on-time is greater than 2μs, orif the ADC measures 0 at the drain, then there is anopen circuit.
Table 1. ADC Response
CONDITION ADC RESPONSE
Shorted string faultLoad full-scale code into register, no conversions on affected channel until power or enable iscycled.
Shorted string fault whileconverting
Immediately load full-scale code into register and cease conversion effort on this channel untilpower or enable is cycled.
ADC register read when it isbeing updated
Previous sample is shifted out through the I2C interface and then the register is updated with thenew measurement.
UVLO Immediately terminate conversions, do not update current register.
STBY Immediately terminate conversions, do not update current register.
SHDN Immediately terminate conversions, do not update current register.
REGISTERFILE UNIT
ADC DAC
POWERMANAGEMENT
OVP
I2C
SYSTEMCLOCK
EXTERNALEVENTS
Figure 3. Digital Block Diagram
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 17www.maximintegrated.com
Maxim Integrated
Overview of the Digital SectionFigure 3 shows the block diagram of the digital section inthe MAX16826. The I2C serial interface provides flexiblecontrol of the IC and is in charge of writing/readingto/from the register file unit. The ADC block is a 7-bit 5-channel SAR ADC. The eighth bit of the ADC data reg-ister indicates an incomplete conversion or timeout hasoccurred. This bit is set whenever the LED current fails tocome into regulation during the DIM PWM on-time. Thisindicates there is either an LED open condition or theCS_ on-time is less than 2μs.
A reason for this among other possibilities is an openLED string condition. This eighth or MSB bit can betested to determine open string faults.
I2C InterfaceThe MAX16826 internal I2C serial interface providesflexible control of the amplitude of the LED current ineach string and the switch-mode regulator output volt-age. It is also able to read the current sink FET drainvoltages, as well as the switching regulator output volt-age through OVP and thus enable some fault detectionand power dissipation minimization. By using an exter-nal μC, the MAX16826 internal control and status regis-ters are also accessed through the standardbidirectional, 2-wire, I2C serial interface.
The I2C interface provides the following I/O functionsand programmability:
• Current sink FET drain and switching regulator out-put-voltage measurement. The measurement foreach channel and the regulator output is stored inits respective register and can be accessedthrough the I2C interface. The SAR ADC measuresthe drain voltage of each current sink FET sequen-tially. This uses one 8-bit register for each channelto store the measurement made by the 7-bit SAR
ADC and 1 bit to indicate a timeout during the ADCconversion cycle.
• Adjustment of the switching regulator output. This isused for adaptive voltage optimization to improveoverall efficiency. The switching regulator output isdownward adjustable by changing its referencevoltage. This uses a 7-bit register.
• Adjustment of the reference voltage of the current-sink regulators. The reference voltage at the nonin-verting input of each of the linear regulator driveamplifiers can be changed to make adjustments inthe current of each LED string for a given senseresistor. The output can be adjusted down from amaximum of 316mV to 97mV in 1.72mV increments.
• Fault reporting. When a shorted string fault or anovervoltage fault occurs, the fault is recorded.
• Standby mode. When a one is entered into thestandby register the IC goes into standby mode.
The 7-bit I2C address is 58h and the 8-bit I2C addressis B1h for a read operation and B0h for a write opera-tion. Address the MAX16826 using the I2C interface toread the state of the registers or to write to the registers.Upon a read command, the MAX16826 transmits thedata in the register that the address register is pointingto. This is done so that the user has the ability to confirmthe data written to a register before the output isenabled. Use the fault register to diagnose any faults.
Serial AddressingThe I2C interface consists of a serial data line (SDA)and a serial clock line (SCL) to achieve bidirectionalcommunication between the master and the slave. TheMAX16826 is a slave-only device, relying upon a mas-ter to generate a clock signal. The master initiates datatransfer to and from the MAX16826 and generates SCLto synchronize the data transfer (Figure 4).
SCL
SDA
tR tF
tBUF
STARTCONDITION
STOPCONDITIONREPEATED START CONDITION START CONDITION
tSU,STO
tHD,STAtSU,STA
tHD,DAT
tSU,DAT tLOW
tHIGH
tHD,STA
Figure 4. 2-Wire Serial Interface Timing Detail
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 18www.maximintegrated.com
I2C is an open-drain bus. Both SDA and SCL are bidi-rectional lines, connected to a positive supply voltageusing a pullup resistor. They both have Schmitt triggersand filter circuits to suppress noise spikes on the bus toensure proper device operation.
A bus master init iates communication with theMAX16826 as a slave device by issuing a START con-dit ion fol lowed by the MAX16826 address. TheMAX16826 address byte consists of 7 address bits anda read/write bit (R/W). After receiving the properaddress, the MAX16826 issues an acknowledge bit bypulling SDA low during the ninth clock cycle.
START and STOP ConditionsBoth SCL and SDA remain high when the bus is notbusy. The master signals the beginning of a transmis-sion with a START (S) condition by transitioning SDAfrom high to low while SCL is high. When the masterhas finished communicating with the MAX16826, itissues a STOP (P) condition by transitioning SDA fromlow to high while SCL is high. The bus is then free foranother transmission (Figure 4). Both START and STOPconditions are generated by the bus master.
Bit TransferEach data bit, from the most significant bit to the leastsignificant bit, is transferred one by one during eachclock cycle. During data transfer, the SDA signal isallowed to change only during the low period of theSCL clock and it must remain stable during the highperiod of the SCL clock (Figure 5).
AcknowledgeThe acknowledge bit is used by the recipient to hand-shake the receipt of each byte of data (Figure 6). Afterdata transfer, the master generates the acknowledgeclock pulse and the recipient pulls down the SDA lineduring this acknowledge clock pulse, such that theSDA line stays low during the high duration of the clockpulse. When the master transmits the data to theMAX16826, it releases the SDA line and the MAX16826takes the control of SDA line and generates theacknowledge bit. When SDA remains high during this9th clock pulse, this is defined as the not acknowledgesignal. The master then generates either a STOP condi-tion to abort the transfer, or a repeated START condi-tion to start a new transfer.
STARTCONDITION
(S)
DATA LINE STABLEDATA VALID
DATA ALLOWEDTO CHANGE
STOPCONDITION
(P)
SCL
SDA
Figure 5. Bit Transfer
SCL
SDABY MASTER
1 2 8 9
S
START CONDITION CLOCK PULSE FOR ACKNOWLEDGMENT
SDABY SLAVE
Figure 6. Acknowledge
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 19www.maximintegrated.com
Accessing the MAX16826The communication between the μC and the MAX16826is based on the usage of a set of protocols defined ontop of the standard I2C protocol definition. They areexclusively write byte(s) and read byte(s).
Write Byte(s)The write byte protocol is as follows:
1) The master sends a START condition.
2) The master sends the 7-bit slave address followedby a write bit (low).
3) The addressed slave asserts an ACK by pullingSDA low.
4) The master sends an 8-bit command code.
5) The slave asserts an ACK by pulling SDA low.
6) The master sends an 8-bit data byte.
7) The slave acknowledges the data byte.
8) The master generates a STOP condition or repeats6 and 7 to write next byte(s).
The command is interpreted as the destination address(register file unit) and data is written in the addressedlocation. The slave asserts a NACK at step 5 if the com-mand is not valid. The master then interrupts the com-munication by issuing a STOP condition. If the addressis correct, the data byte is written to the addressed reg-ister. After the write, the internal address pointer isincreased by one. When the last location is reached, itcycles to the first register.
Read Byte(s)The read sequence is:
1) The master sends a START condition.
2) The master sends the 7-bit slave address plus awrite bit (low).
3) The addressed slave asserts an ACK on the dataline.
4) The master sends an 8-bit command byte.
5) The active slave asserts an ACK on the data line.
6) The master sends a repeated START condition.
7) The master sends the 7-bit slave address plus aread bit (high).
8) The addressed slave asserts an ACK on the dataline.
9) The slave sends an 8-bit data byte.
10) The master asserts a NACK on the data line tocomplete operations or asserts an ACK andrepeats 9 and 10.
11) The master generates a STOP condition.
The data byte read from the device is the content of theaddressed location(s). Once the read is done, the inter-nal pointer is increased by one. When the last location isreached, it cycles to the first one. If the device is busy orthe address is not correct (out of memory map), thecommand code is not acknowledged and the internaladdress pointer is not altered. The master then inter-rupts the communication by issuing a STOP condition.
S ACKSLAVE ADDRESS R/W
7 BITS 0
COMMAND
8 BITS
ACK ACK PDATA
COMMAND BYTE: SELECT REGISTER TO WRITE DATA BYTE DATA GOES INTO THE REGISTERSET BY THE COMMAND BYTE
8 BITS
WRITE BYTE FORMAT
Figure 7. Write Byte Format
S ACKSLAVE ADDRESS R/W
7 BITS 0
ACKSLAVE ADDRESS R/W
7 BITS 1
COMMAND
8 BITS
ACK SR NACK PDATA
COMMAND BYTE: PREPARE DEVICE FORFOLLOWING READ
DATA BYTE DATA COMES FROM THEREGISTER SET BY THE COMMAND BYTE
8 BITS
READ BYTE FORMAT
Figure 8. Read Byte Format
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 20www.maximintegrated.com
Register File UnitThe register file unit is used to store all the control infor-mation from the SDA line and configure the MAX16826for different operating conditions. The register fileassignments of the MAX16826 are in Table 2.
Registers 00h to 03h: String Current ProgrammingThese registers are used to program LED string 1 toLED string 4 current sink values. For each LED string,CS1–CS4 inputs are connected to the source of theexternal current sink FET and internally are connectedto the inverting input of the internal transconductanceamplifier. The noninverting input of this amplifier is con-nected to the output of an internal DAC programmedby these registers. As the DAC is incremented, its out-put voltage decreases from 316mV to 97mV in 1.72mVsteps by the data written in the register 00h to 03h;thus, the steady-state voltage at CS1–CS4 is given bythe following formula:
VCS1,2,3,4 = 316mV - (1.72mV x RegisterValue[6:0])
For example, if 00h is set to 20h, then the CS1 voltage is:
VCS1 = 316mV - 1.72mV x 32 = 265.3mV
Register 04h: Switching RegulatorOutput ProgrammingSet the switching regulator output voltage by connect-ing FB to the center of a resistive voltage-dividerbetween the switching regulator output and GND. VFBis regulated to a voltage from 876mV to 1.25V (typ) setby the register 04h through the I2C interface.
The FB reference voltage can be decreased from 1.25V,its maximum value, by approximately 2.9mV steps. Thesteady-state voltage at FB then is regulated to:
VFB = 1.25V - (2.91mV x 04h[6:0])
Registers 05h to 08h: External Current-Sink FET Drain Voltage ADC ReadingsThese registers store the drain voltages of the externalcurrent sink FETs. For each register, bits 6–0 are theconversion data of the ADC outputs. Bit 7 is used toshow if the conversion is terminated by the ADC (indi-cated by 0) or if there is an internal timeout (indicatedby 1). If the drain voltage exceeds the preset referencevoltage, the corresponding LED string fault bit is assert-ed. See the Faults and Fault Detection section for moreinformation on the internal timeout function.
Register 09h: Switching RegulatorVoltage ADC OutputBits 6-0 of this register store the voltage present atOVP. This voltage is a scaled down version of theswitching regulator output voltage. Bit 7 is not used.
Register 0Ah: Fault Status RegisterThis register stores all the external events or fault infor-mation such as overvoltage and shorted LED stringfaults. The fault events are logged only if the system isnot in standby mode and their active states are longerthan one clock cycle. Cycle enable or power to clear thefault status register. Initiating standby mode using theI2C interface can also be used to clear the fault status
Table 2. Register File Assignments
REGISTERADDRESS
R/WUSED BITRANGE
RESETVALUE
DESCRIPTION
00h R/W [6:0] 00h LED String 1 current programming value.
01h R/W [6:0] 00h LED String 2 current programming value.
02h R/W [6:0] 00h LED String 3 current programming value.
03h R/W [6:0] 00h LED String 4 current programming value.
04h R/W [6:0] 00h Switching regulator output voltage programming value.
05h R [7:0] 00h LED String 1 external FET drain voltage ADC output.
06h R [7:0] 00h LED String 2 external FET drain voltage ADC output.
07h R [7:0] 00h LED String 3 external FET drain voltage ADC output.
08h R [7:0] 00h LED String 4 external FET drain voltage ADC output.
09h R [6:0] 00h OVP voltage, ADC output.
0Ah R [5:0] 00h Fault status register.
0Bh R/W [0] 00h Device standby command.
0Ch R [2:0] — Device revision code.
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 21www.maximintegrated.com
register. First, activate standby mode and then deacti-vate this mode using the I2C interface. Next, perform aread operation on the fault status register. The old faultinformation is reported in this first read operation. Theconclusion of the read operation clears the data con-tained in the register. Subsequent read o perations con-firm that the fault status register has been cleared.
The description of this register is as follows:
Bit 0: Overvoltage sense flag. This flag is set if the volt-age at OVP exceeds 1.25V; switching stops until poweror the enable or standby is cycled.
• Bit 1: Not used.
• Bit 2: LED string 1 shorted flag. A diode short in LEDstring 1 has been detected if this bit is set.
• Bit 3: LED string 2 shorted flag. A diode short in LEDstring 2 has been detected if this bit is set.
• Bit 4: LED string 3 shorted flag. A diode short in LEDstring 3 has been detected if this bit is set.
• Bit 5: LED string 4 shorted flag. A diode short in LEDstring 4 has been detected if this bit is set.
Register 0Bh Bit 0: Device Standby CommandWhen register 0Bh bit 0 is set to 1, the IC enters a low-current standby mode. In this mode, the system clock isoff and no operation is allowed. Set this bit to 0 to leavestandby mode and back to normal operation mode.
Register 0Ch Bit 2-0: Device Revision CodeThese 3 bits are a hardwired value that identifies theIC’s revision.
Applications Information
Programming LED CurrentsThe MAX16826 uses sense resistors (R28, R29, R30,R31 in the Typical Application Circuit) to set the outputcurrent for each LED string. To set the LED current for aparticular string, connect a sense resistor across thecorresponding current-sense input (CS1–CS4) andGND. For optimal accuracy, connect the low-side of thecurrent-sense resistors to GND with short traces. Thevalue needed for the sense resistor for a given currentis calculated with the equation below:
R31 = VCS1/IOUT1
where VCS1 can be set from 97mV to 316mV by theinternal registers through the I2C interface and IOUT1 isthe desired LED string 1 current.
Calculating the Value of Peak Current-Limit ResistorThe value of R12 sets the peak switching current thatflows in the switching FET (Q1). Set the value of resistorR12 using the equation below:
R12 = 0.19/(1.2 x IPK)
where IPK is the peak inductor current at minimum inputvoltage and maximum load.
Boost Inductor ValueThe value of the boost inductor is calculated using thefollowing equation:
where VINMIN is the minimum input voltage, VOUT is thedesired output voltage, and fSW is the switching fre-quency, and ΔIL is the peak-to-peak ripple in the boostinductor. Higher inductor values lead to lower ripple butat a higher cost and size. Choose an inductor value thatgives peak-to-peak ripple current in the order of 30% to40% of the average current in the inductor at low-lineand full-rated load. This choice of inductor is a compro-mise between cost, size, and performance for the boostconverter.
Setting Output VoltageSet the switch regulator output voltage by connectingFB to the center of a resistive voltage-divider betweenthe switching regulator output and GND. VFB is regulat-ed to a voltage from 0.88V to 1.25V (typ) set by aninternal register through the I2C interface. Choose R13and R14 in the Typical Application Circuit for a reason-able bias current in the resistive divider and use the fol-lowing formula to set the output voltage:
VOUT = (1 + R13/R14) x VFB
where VFB is the regulated voltage set by the internalregister.
Adaptive Voltage OptimizationThe availability of the digitized switching regulator outputvoltage and current sink drain voltages and the ability tochange the switching regulator output voltage providethe ability to do adaptive voltage optimization. A slow dig-ital control loop is established with an external μC closingthe loop. Firmware residing in the external μC is tasked toread each one of the current sink FET drain voltages andselect the minimum value of the four LED strings. Theminimum value is subtracted from the scaled output volt-age reading, and then the switching regulator output isforced to maintain the difference required to provide cur-rent regulation in the current sink FETs.
L1 V V V
V f IINMIN OUT INMIN
O SW L=
× ( )× ×
−
UT Δ
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 22www.maximintegrated.com
Switching Noise Effectson ADC ReadingsExcessive switching noise can corrupt the ADC read-ings on the current sink MOSFET drains. Proper PCBlayout is critical to minimize this noise. The output diodeshould be selected appropriately. The capacitance andreverse recovery characteristics of the output diodecontribute to ground noise. Diodes with lower capaci-tance and lower reverse recovery time will result inlower current spikes at the turn on edge of the boostswitch. The lower current spike will result in lowerground noise. Another method to reduce the groundnoise is to add a gate resistor in series with the gate ofthe switching MOSFET. For most applications the gateresistor should be in the range of 4.7 to 10ohms. Caremust be taken in selecting the gate resistor value, dueto power dissipation increase on the boost transistor. Ahigher resistor value reduces the switching noise, butpower dissipation due to switching losses will increase.The ground noise should be measured by measuring
the voltage between the ground of the input capacitorthat is farthest from the IC on the PCB and the groundof the MAX16826. The pins 1,2 and 3 are the groundpins of the MAX16826. To prevent problems on theADC readings of the MAX16826 the ground noise mea-sured from the IC ground to the input capacitor groundshould be less than 0.5V peak to peak on a wide band-width scope using a wide bandwidth probe. A widebandwidth scope must have a bandwidth greater than150MHz.
SEPIC TopologyThe SEPIC power topology is very useful when theinput voltage is expected to be higher or lower than theoutput voltage of the switching regulator stage asrequired by the number of LEDs used in a single string.
The SEPIC topology is more complex than the simpleboost topology and it requires the use of two additionalenergy storage components, L2 and C25, in Figure 9.
MAX16826
Q2
R26
R28
C41R21R23R25R27
Q1
R12R17
Q3
R24
R29
C42
Q4
R22
R30
C43
Q5
R20R18C29
R31
CS1DL1
C44
GNDGND
PGND
GND
GND
GND
VCC
R19
GND
RTCT
GNDGND GND
CSS
CS4
C33 C32
DL4CS3DL3CS2DL2
DR1DR2DR3DR4
C30
GNDGND
D1
L2
GND
C27
OVPFB
C25
COMPRSCIN CSDL
DIMMING INPUTS
SYST
EM IN
TERF
ACE
R16
R15
GND
R14
R13
GND
R11
VOUTL1
GND
C26
VIN
SCLI2C INTERFACE
SDA
SYNC/EN
DIM4DIM3DIM2DIM1
SCLSDA
ENABLE
DIM
GND
SYSTEMµC
GND
C28R35R32 R33 R34
Figure 9. SEPIC-Based LED Driver
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 23www.maximintegrated.com
PCB Layout and RoutingCareful PCB layout is important for proper operation.Use the following guidelines for good PCB layout:
• Minimize the area of the high current-switching loopof the rectifier diode, switching FET, sense resistor,and output capacitor to avoid excessive switchingnoise. Use wide and short traces for the gate-driveloop from DL, to the FET gate, and through the cur-rent-sense resistor, then returning to the IC PGNDand GND.
• Connect high-current input and output componentswith short and wide connections. The high-currentinput loop is from the positive terminal of the inputcapacitor to the inductor, to the switching FET, tothe current-sense resistor, and to the negative ter-minal of the input capacitor. The high-current outputloop is from the positive terminal of the input capac-itor to the inductor, to the rectifier diode, to the posi-tive terminal of the output capacitor, reconnectingbetween the output capacitor and input capacitorground terminals. Avoid using vias in the high-cur-rent paths. If vias are unavoidable, use multiple viasin parallel to reduce resistance and inductance.
• Place the feedback and even voltage-divider resis-tors as close to FB and OVP as possible. Thedivider center trace should be kept short. Placingthe resistors far away causes the sensing trace tobecome antennas that can pick up switching noise.Avoid running the sensing traces near drain con-nection of the switching FET.
• Place the input bypass capacitor as close to thedevice as possible. The ground connection of thebypass capacitor should be connected directly toGND with a wide trace.
• Minimize the size of the switching FET drain nodewhile keeping it wide and short. Keep the drainnode away from the feedback node and ground. Ifpossible, avoid running this node from one side ofthe PCB to the other. Use DC traces as shields, ifnecessary.
• Provide large enough cooling copper traces for theexternal current sink FETs. Calculate the worst-casepower dissipation and allocate sufficient area forcooling.
• Refer to the MAX16826 Evaluation Kit for an exam-ple of proper board layout.
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 24www.maximintegrated.com
Typical Application Circuit
MAX
1682
6
Q2
R26
R28
C41
R21
R23
R25
R27
Q1
R12
R17
Q3
R24
R29
C42
Q4
R22 R3
0
C43
Q5
R20
R18
C29
R31
CS1
DL1
C44
GND
GND
PGND
GND
GND
GND
V CC
R19
GND
RTCT
GND
GND
GND
CSS
CS4
C33
C32
DL4
CS3
DL3
CS2
DL2
DR1
DR2
DR3
DR4
C30
GND
GND
D1 C28
GND
C27
OVPFB
COM
PRS
CIN
CSDL
SYSTEM INTERFACE
R16
R15
GND
R14
R13
GND
R11
V OUT
L1
GND
C26
V IN
(40V
LOA
DDU
MP
OK) SC
LSD
A
SYNC
/EN
DIM
4DI
M3
DIM
2DI
M1
SCL
SDA
ENAB
LEDIM
GND
SYST
EMµ
CDI
MM
ING
INPU
TS
I2 C IN
TERF
ACE
R35
R32
R33
R34
BOOS
T LE
D DR
IVER
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated | 25www.maximintegrated.com
Chip InformationPROCESS: BiCMOS
MAX16826
TQFN(5mm x 5mm)
TOP VIEW
29
30
28
27
12
11
13
GND
RTCT
SNYC
/EN
CSS
COM
P
14
PGND
CS3
DL2
CS2
DL3
DR1
DL1
1 2
DR4
4 5 6 7
2324 22 20 19 18
IN
CS
DIM2
DIM1
SCL
SDA
GND
DR2
3
21
31 EP
EXPOSED PAD.
10VCC RSC
32 9DL OVP
DL4
26 15 DIM3CS4
25 16 DIM4
FBCS
1
8
17
DR3
PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
32 TQFN-EP T3255-4 21-0140
Pin Configuration
+Denotes a lead(Pb)-free/RoHS-compliant package.*EP = Exposed pad./V denotes an automotive qualified part.
Package InformationFor the latest package outline information and land patterns (foot-prints), go to www.maximintegrated.com/packages. Note that a“+”, “#”, or “-” in the package code indicates RoHS status only.Package drawings may show a different suffix character, but thedrawing pertains to the package regardless of RoHS status.
Ordering Information
PART TEMP RANGE PIN-PACKAGE
MAX16826ATJ+ -40°C to +125°C 32 TQFN-EP*
MAX16826ATJ/V+ -40°C to +125°C 32 TQFN-EP* MAX16826AGJ/VY+ -40°C to +125°C 32 QFN-EP*
MAX16826BATJ+ -40°C to +125°C 32 TQFN-EP*
MAX16826BATJ/V+ -40°C to +125°C 32 TQFN-EP*
MAX16826 Programmable, Four-String HBLED Driver with Output-Voltage
Optimization and Fault Detection
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patentlicenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min andmax limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. © 2016 Maxim Integrated Products, Inc. | 26
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Revision History
REVISION NUMBER
REVISION DATE DESCRIPTION PAGES
CHANGED
0 8/08 Initial release —
1 3/09 Added automotive version, updated Features, EC table, Typical Operating Characteristics, Switching Preregulator Stage, Oscillator, Analog-to-Digital (ADC), Faults and Fault Detection sections
1, 2, 5, 6, 11, 14–17, 20
2 12/09 Improve definition of minimum on-time for proper ADC operation 5, 10, 16
3 6/10 Added MAX16826B part 2–5, 25
4 12/11 Added MAX16826AGJ/VY+ to data sheet 25
5 10/13 Added Switching Noise Effects on ADC Readings section 22
6 2/15 Updated Benefits and Features section 1
7 2/16 Added missing lead(Pb)-Free designations in Ordering Information table 25
7.12525
Corrected revision date 261,