Upload
hoanglien
View
269
Download
8
Embed Size (px)
Citation preview
Material Safety Data Sheet (MSDS) Inventory
Product Name Product Description Catalog #’s
Absorbent Sheet Scapa Polymerics L-525, L-525S, and L528 Superabsorbent Laminate
1102-36
Blood Culture Vial Standard BACTEC Standard/10 Aerobic/F Culture Vials
442260
Blood Culture Vial Lytic BACTEC Lytic/10 Aerobic/F Culture Vials
442265
Blue (Light) Top Tube (Protime)
Greiner Vacuette® 9NC Coagulation Tube with Sodium Citrate 3, 2%
454351
Culture Swab Starplex Starswab II Bacteriology Culture Collection and Transport, Product Code SP130X
14211-754
Green. Light Green, Post Green
GreinerVacuette® LH Lithium Heparin Separator 454247, 454447
Green Top BD Vacutainer Plasma Separator Tube with Lithium Heparin Separator
367962
Ice Pack 12 oz Koolit Gel Paks, Series 600
89049-358
Ice Pack 3 oz Polar Pack® Reusable Refrigerant Pack
16000-068
Lavender Top Tube – Greiner
Greiner Vacuette® K3E K3EDTA 454222
Para-Pak® Stool Bottle 10% Formalin
Meridian Bioscience Para-Pak® 10% Formalin Para-Pak® 10% Formalin ULTRA
900612
Para-Pak® LV PVA Fixative Meridian Bioscience Para-Pak®LV-PVA Fixative (Low Viscosity Polyvinyl Alcohol Fixative)
301012
Red Top – Greiner
Greiner Vacuette® Z Serum Separator Clot Activator
456073
Royal Blue Top Tube – Greiner
Greiner Vacuette® NH Trace Elements Sodium Heparin
456275
White Top Tube – Greiner
Greiner Vacuette® K2E K2EDTA Sep 456024
Note: If you receive a product from Satellite Laboratory Services that is not listed above it is because it presents
no hazards and there is no MSDS published for the product.
031511
1 of 6
MSDS Material Safety Data Sheet
Scapa North America • 609 Barnet Blvd • Renfrew, Ontario
(613) 432-8545 • Fax: (613) 432-9434 • www.scapana.com
DATE: September 5, 2007
1. IDENTIFICATION:
• Product Name: Cable tape • Product Numbers: L513, L515, L525, L525S & L528 • Description: A lamination of cellulose non woven fabric and super absorbent polymer
2. COMPOSITION / INGREDIENTS:
• Cellulose based non woven fabric • Super absorbent polymer, a sodium salt of polyacrylic acid, CAS # 9033-79-8
3. HAZARDS IDENTIFICATION:
• Eye(s): Dust can be a temporary eye irritant. • Skin Contact: Prolonged contact should be avoided, may cause redness and/or irritation. • Skin Absorption: Not likely to be absorbed. • Ingestion: Not likely to be a problem because of physical form. • Inhalation: Acute (short term) inhalation of dust may cause mild irritation of upper respiratory tract
(nose and throat) and lungs. • Systematic & Other Effects: None known. • HMIS Rating:
o Health: 0 o Flammability: 1 o Reactivity: 0
MSDS Contact Phone Numbers
Regular Business Hours: Technical Department at: (613) 432-8545
2 of 6
MSDS Material Safety Data Sheet
Scapa North America • 609 Barnet Blvd • Renfrew, Ontario
(613) 432-8545 • Fax: (613) 432-9434 • www.scapana.com
4. FIRST AID MEASURES:
• Eye(s): Dust; Flush eyes with water, if irritation persists, obtain medical assistance. Mechanical injury;
obtain medical assistance • Skin Contact: No first aid measures normally required. Wash skin with soap and water. • Ingestion: No first aid measures normally required. • Inhalation: No first aid measures normally required.
5. FIRE FIGHTING MEASURES:
• Flash Point: N/A • Method Used: N/A • Extinguishing Media: Water fog, foam, dry chemical, Carbon Dioxide • Flammable Limits: N/A • LFL: N/A • UFL: N/A • Special Fire Fighting Equipment and Hazards: Recommend self-contained breathing apparatus
for serious fires. Products of combustion same as ordinary combustibles. Carbon, carbon dioxide, carbon monoxide; emits dense smoke when burned. Above 200C thermal decomposition giving toxic byproducts, organic derivatives, carbon oxides, can occur. CAUTION: The material becomes slippery if flushed or in contact with water.
6. ACCIDENTAL RELEASE MEASURES:
• Sweep up and collect for disposal. See Section 8 and Section 13. • CAUTION: The material becomes slippery if flushed or in contact with water.
7. HANDLING AND STORAGE:
• Handling: Observe normal industrial hygiene. • Storage: Keep material in dry location and sealed to minimize water absorption before use. Avoid
storing near strong oxidizers. Avoid sources of ignition. Use caution when stacking to avoid unstable conditions. Store at temperatures below 140F. Store in a sprinklered warehouse.
3 of 6
MSDS Material Safety Data Sheet
Scapa North America • 609 Barnet Blvd • Renfrew, Ontario
(613) 432-8545 • Fax: (613) 432-9434 • www.scapana.com
8. EXPOSURE CONTROLS / PERSONAL PROTECTION:
• Protective Provisions: Ensure adequate room ventilation and / or exhaust in work areas. • Control parameters: Keep free respirable dust (<10 micron) below 0.05 mg/m3 • PPE
• Respiratory Protection: Use mask appropriate for your operation to protect from any dust and
respiratory particles. • Eye Protection: Not normally necessary. Safety glasses or goggles are recommended. • Hand: gloves as necessary • Protective Cloths: non skid boots as necessary • Hygiene Measures: avoid contact with skin. Prohibit inhalation of dust. Keep dust out of eyes.
9. PHYSICAL AND CHEMICAL PROPERTIES:
• Boiling Point: N/A • VAP Press: N/A • VAP Density (Air = 1): N/A • Appearance and Odor: Rolls or spools of white tape • Sol. In Water: swell in water • % Volatile by Wt.: 1.0% or less
10. STABILITY AND REACTIVITY:
• Stability: Stable • Incompatibility: Strong oxidizing agents • Hazardous Decomposition Products: Temperatures above 200C will result in thermal
decomposition giving toxic byproducts; organic vapors, carbon monoxide. CO, CO2, unknown hydrocarbons
• Hazardous Polymerization: Will not occur • Additional: swells in contact with water. Store protected from moisture.
4 of 6
MSDS Material Safety Data Sheet
Scapa North America • 609 Barnet Blvd • Renfrew, Ontario
(613) 432-8545 • Fax: (613) 432-9434 • www.scapana.com
11. TOXOLOGICAL INFORMATION:
• Fabric: • None.
• Super Absorbent: • Corrosiveness: none • Acute Toxicity: Oral rat LD50: 2000 mg/kg • Skin irritation: Not an irritant (Human, Rabbit) • Eye irritation: Not an irritant (Rabbit) • Ames Mutagenicity Test: non-mutagenic • Skin contact sensitization: non-sensitizing (Rat) • Symptoms of exposure: Dust may cause eye, nasal or bronchial irritation • Cytotoxicity: non-cytotoxic (L929 cell)
12. ECOLOGICAL INFORMATION:
• Persistence / Degradability: Not readily biodegradable.
13. DISPOSAL CONSIDERATIONS:
• Action to Take for Spills: In the event of a spill, or need to dispose of unwanted material, place in an approved solid waste disposal area in accordance with existing environmental regulation.
• Disposal Method: Landfill or incineration per local, state or federal EPA regulations. Be aware that state and local requirements may differ widely depending on location and may in many cases be different from federal rules.
14. TRANSPORT INFORMATION:
• DOT Classification: Not regulated • Dot Hazard Class: N/A
5 of 6
MSDS Material Safety Data Sheet
Scapa North America • 609 Barnet Blvd • Renfrew, Ontario
(613) 432-8545 • Fax: (613) 432-9434 • www.scapana.com
15. REGULATORY INFORMATION:
OSHA: This MSDS is provided to comply with provisions of hazard Communication Standard (29CFR1910.1200) TSCA: All components of this product are in compliance with the inventory listing requirements of the U.S. Toxic Substances Control Act Chemical substances Inventory.
SARA Title III: This product does not contain a chemical which is listed in Section 313 at or above de minimis
concentrations.
FDA: This product is not registered with the FDA. This product is not approved for use as articles or components of articles intended for repeated contact with food. USDA: This product has not been evaluated by USDA for use in packaging material in direct contact with meat or poultry food products prepared under federal inspection. State Regulations: • none
6 of 6
MSDS Material Safety Data Sheet
Scapa North America • 609 Barnet Blvd • Renfrew, Ontario
(613) 432-8545 • Fax: (613) 432-9434 • www.scapana.com
16. OTHER INFORMATION:
• Refer to product technical data sheet for information on specific product characteristics and applications.
• All statements, technical information and recommendations set forth herein are based on information or tests which Scapa North America believes to be reliable as of the date of this material safety data sheet. However, nothing contained in this information is to be taken as a representation, guarantee or warranty for which Scapa North America bears any legal responsibility. Scapa North America urges persons receiving this information to make their own determination as to the information’s suitability and completeness for their particular application(s).
• The data in this material safety data sheet relates only to the specific material designated herein and does not relate to use in combination with any other material or process.
Form Template: REN 403A
Page 1/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 01/07/2008
DR
1 Identification of substance:
· Product name: BACTEC Standard/10 Aerobic/F Culture Vials· Catalog number: 442260
· Manufacturer/Supplier:BD Diagnostic Systems7 Loveton CircleSparks, MD 21152Telephone: (410) 771 - 0100 or (800) 638 - 8663
· Information department: Technical Services· Emergency information:
In case of a chemical emergency, spill, fire, exposure, or accident contact BD Diagnostic Systems (410) 771-0100or (800)-638-8663, or ChemTrec at (800) 424-9300.
2 Composition/Data on components:
· Chemical characterization:· CAS No. Description:
Not applicable
3 Hazards identification
· Hazard description:This product contains no hazardous constituents, or the concentration of all chemical constituents are below theregulatory threshold limits described by Occupational Safety Health Administration Hazard CommunicationStandard 29 CFR 1910.1200, the Canada's Workplace Hazardous Materials Information System (WHMIS) andthe European Directive 91/155/EEC, and 93/112/EC.
· NFPA ratings (scale 0-4)
00
0Health = 0Fire = 0Reactivity = 0
· HMIS ratings (scale 0-4) HEALTH
FIRE
REACTIVITY
0
0
0
Health = 0Fire = 0Reactivity = 0
4 First aid measures
· General information No special measures required.· After inhalation Seek medical treatment in case of complaints.· After skin contact Immediately wash with water and soap and rinse thoroughly.· After eye contact
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.· After swallowing If symptoms persist consult doctor.· Information for doctor Show this product label or this MSDS.
USA
(Contd. on page 2)
Page 2/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 01/07/2008
Product name: BACTEC Standard/10 Aerobic/F Culture Vials
(Contd. of page 1)
DR
5 Fire fighting measures
· Suitable extinguishing agentsCO2, ABC multipurpose dry chemical or water spray. Fight larger fires with water spray or alcohol resistantfoam.
· Protective equipment: No special measures required.
6 Accidental release measures
· Person-related safety precautions: Not required.· Measures for environmental protection: Wipe up with damp sponge or mop.· Measures for cleaning/collecting: No special measures required.· Additional information: No dangerous substances are released.
7 Handling and storage
· Handling· Information for safe handling: No special measures required.· Information about protection against explosions and fires: No special measures required.
· Storage· Requirements to be met by storerooms and receptacles: No special requirements.· Information about storage in one common storage facility: Store away from oxidizing agents.· Further information about storage conditions: None.
8 Exposure controls and personal protection
· Additional information about design of technical systems: No further data; see item 7.
· Components with limit values that require monitoring at the workplace: Not required.· Additional information: The lists that were valid during the creation were used as basis.
· Personal Protective Equipment· General protective and hygienic measures
The usual precautionary measures for handling chemicals should be followed.· Breathing equipment:
In case of brief exposure, use a chemical fume hood or a NIOSH/MSHA-approved respirator.· Protection of hands:
Chemical resistant gloves (i.e. nitrile, or equivalent).
· Eye protection: Safety glasses· Body protection: Protective work clothing (lab coat).
9 Physical and chemical properties:
· General Information
Form: Liquid(Contd. on page 3)
USA
Page 3/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 01/07/2008
Product name: BACTEC Standard/10 Aerobic/F Culture Vials
(Contd. of page 2)
DR
Color: Yellow tintOdor: Sulphurous
· Change in conditionMelting point/Melting range: Not determinedBoiling point/Boiling range: Not determined
· Flash point: Not applicable
· Danger of explosion: Product does not present an explosion hazard.
· Density: Not determined
· Solubility in / Miscibility withWater: Soluble
10 Stability and reactivity
· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.· Materials to be avoided:· Dangerous reactions No dangerous reactions known· Dangerous products of decomposition: No dangerous decomposition products known.
11 Toxicological information
· Acute toxicity:· Primary irritant effect:· on the skin: No irritating effect.· on the eye: No irritating effect.· Sensitization: No sensitizing effects known.· Additional toxicological information:
The product is not subject to OSHA classification according to internally approved calculation methods forpreparations.When used and handled according to specifications, the product does not have any harmful effects according toour experience and the information provided to us.The substance is not subject to classification.
12 Ecological information:
· Ecotoxical effects:· Other information:
The ecological effects have not been thoroughly investigated, but currently none have been identified.· Additional ecological information:· General notes: Generally not hazardous for water.
13 Disposal considerations
· Product:· Recommendation
Smaller quantities can be disposed of with solid waste.Dispose of material in accordance with federal (40 CFR 261.3), state and local requirements.
(Contd. on page 4) USA
Page 4/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 01/07/2008
Product name: BACTEC Standard/10 Aerobic/F Culture Vials
(Contd. of page 3)
DR
This product is not considered a RCRA hazardous waste.
· Uncleaned packagings:· Recommendation: Disposal must be made according to state and federal regulations.· Recommended cleansing agent: Water, if necessary with cleansing agents.
14 Transport information
· DOT regulations:
· Hazard class: -
· Land transport ADR/RID (cross-border)· ADR/RID class: -
· Maritime transport IMDG:· IMDG Class: - · Marine pollutant: No
· Air transport ICAO-TI and IATA-DGR:· ICAO/IATA Class: -
· Transport/Additional information:If a dashed line appears in the Hazard Class section for the type of transportation, this indicates the product isnot regulated for transportation.
15 Regulations· SARA Section 355 (extremely hazardous substances)
Substance is not listed.
· SARA Section 313 (specific toxic chemical listings)Substance is not listed.
· TSCA (Toxic Substances Control Act)Substance is not listed.
· California Proposition 65 - Chemicals known to cause cancerSubstance is not listed.
· California Proposition 65 - Chemicals known to cause reproductive toxicity for females:Substance is not listed.
· California Proposition 65 - Chemicals known to cause reproductive toxicity for males:Substance is not listed.
· California Proposition 65 - Chemicals known to cause developmental toxicity:Substance is not listed.
· Carcinogenic categories· NTP (National Toxicology Program)
Substance is not listed.
· TLV (Threshold Limit Value established by ACGIH)Substance is not listed.
· Product related hazard information:Observe the general safety regulations when handling chemicals
(Contd. on page 5) USA
Page 5/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 01/07/2008
Product name: BACTEC Standard/10 Aerobic/F Culture Vials
(Contd. of page 4)
DR
The substance is not subject to classification according to the sources of literature known to us.The product is not subject to identification regulations pertaining to regulations on hazardous materials.
· National regulations
· Water hazard class: Generally not hazardous for water.
16 Other information:To the best of our knowledge, the information contained herein is accurate. However, neither Becton, Dickinsonand Company or any of its subsidiaries assumes any liabilities whatsoever for the accuracy or completeness ofthe information contained herein. Final determination of suitability of any material is the sole responsibility of theuser. All materials may present unknown hazards and should be used with caution. Although certain hazards aredescribed herein, we can not guarantee that these are the only hazards that exist.
· Department issuing MSDS:Safety and Environment DepartmentMSDS created by Michael J. Spinazzola
· Contact: Technical Service Representative USA
Page 1/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 12/21/2007
DR
1 Identification of substance:
· Product name: BACTEC Lytic/10 Anaerobic/F Culture Vials· Catalog number: 442265
· Manufacturer/Supplier:BD Diagnostic Systems7 Loveton CircleSparks, MD 21152Telephone: (410) 771 - 0100 or (800) 638 - 8663
· Information department: Technical Services· Emergency information:
In case of a chemical emergency, spill, fire, exposure, or accident contact BD Diagnostic Systems (410) 771-0100or (800)-638-8663, or ChemTrec at (800) 424-9300.
2 Composition/Data on components:
· Chemical characterization· Description: Mixture consisting of the following components.
· Dangerous components: Void
3 Hazards identification
· Hazard description:This product contains no hazardous constituents, or the concentration of all chemical constituents are below theregulatory threshold limits described by Occupational Safety Health Administration Hazard CommunicationStandard 29 CFR 1910.1200, the Canada's Workplace Hazardous Materials Information System (WHMIS) andthe European Directive 91/155/EEC, and 93/112/EC.
· NFPA ratings (scale 0-4)
00
0Health = 0Fire = 0Reactivity = 0
· HMIS ratings (scale 0-4) HEALTH
FIRE
REACTIVITY
0
0
0
Health = 0Fire = 0Reactivity = 0
4 First aid measures
· General information No special measures required.· After inhalation Seek medical treatment in case of complaints.· After skin contact Immediately wash with water and soap and rinse thoroughly.· After eye contact
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.· After swallowing If symptoms persist consult doctor.· Information for doctor Show this product label or this MSDS.
USA
(Contd. on page 2)
Page 2/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 12/21/2007
Product name: BACTEC Lytic/10 Anaerobic/F Culture Vials
(Contd. of page 1)
DR
5 Fire fighting measures
· Suitable extinguishing agentsCO2, ABC multipurpose dry chemical or water spray. Fight larger fires with water spray or alcohol resistantfoam.
· Protective equipment: No special measures required.
6 Accidental release measures
· Person-related safety precautions: Not required.· Measures for environmental protection: Wipe up with damp sponge or mop.· Measures for cleaning/collecting: No special measures required.· Additional information: No dangerous substances are released.
7 Handling and storage
· Handling· Information for safe handling: No special measures required.· Information about protection against explosions and fires: No special measures required.
· Storage· Requirements to be met by storerooms and receptacles: No special requirements.· Information about storage in one common storage facility: Store away from oxidizing agents.· Further information about storage conditions: None.
8 Exposure controls and personal protection
· Additional information about design of technical systems: No further data; see item 7.
· Components with limit values that require monitoring at the workplace:The product does not contain any relevant quantities of materials with critical values that have to be monitored atthe workplace.
· Additional information: The lists that were valid during the creation were used as basis.
· Personal Protective Equipment· General protective and hygienic measures
The usual precautionary measures for handling chemicals should be followed.· Breathing equipment:
In case of brief exposure, use a chemical fume hood or a NIOSH/MSHA-approved respirator.· Protection of hands:
Chemical resistant gloves (i.e. nitrile, or equivalent).
· Eye protection: Safety glasses· Body protection: Protective work clothing (lab coat).
USA
(Contd. on page 3)
Page 3/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 12/21/2007
Product name: BACTEC Lytic/10 Anaerobic/F Culture Vials
(Contd. of page 2)
DR
9 Physical and chemical properties:
· General Information
Form: LiquidColor: Light yellowOdor: Sulphurous
· Change in conditionMelting point/Melting range: Not determinedBoiling point/Boiling range: Not determined
· Flash point: Not applicable
· Danger of explosion: Product does not present an explosion hazard.
· Density: Not determined
· Solubility in / Miscibility withWater: Soluble
10 Stability and reactivity
· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.· Materials to be avoided:· Dangerous reactions No dangerous reactions known· Dangerous products of decomposition: No dangerous decomposition products known.
11 Toxicological information
· Acute toxicity:· Primary irritant effect:· on the skin: No irritating effect.· on the eye: No irritating effect.· Sensitization: No sensitizing effects known.· Additional toxicological information:
The product is not subject to OSHA classification according to internally approved calculation methods forpreparations.When used and handled according to specifications, the product does not have any harmful effects according toour experience and the information provided to us.This product or product container contains dry natural rubber latex.
12 Ecological information:
· Ecotoxical effects:· Other information:
The ecological effects have not been thoroughly investigated, but currently none have been identified.· Additional ecological information:· General notes: Generally not hazardous for water.
USA
(Contd. on page 4)
Page 4/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 12/21/2007
Product name: BACTEC Lytic/10 Anaerobic/F Culture Vials
(Contd. of page 3)
DR
13 Disposal considerations
· Product:· Recommendation
Smaller quantities can be disposed of with solid waste.Dispose of material in accordance with federal (40 CFR 261.3), state and local requirements.This product is not considered a RCRA hazardous waste.
· Uncleaned packagings:· Recommendation: Disposal must be made according to state and federal regulations.· Recommended cleansing agent: Water, if necessary with cleansing agents.
14 Transport information
· DOT regulations:
· Hazard class: -
· Land transport ADR/RID (cross-border)· ADR/RID class: -
· Maritime transport IMDG:· IMDG Class: - · Marine pollutant: No
· Air transport ICAO-TI and IATA-DGR:· ICAO/IATA Class: -
· Transport/Additional information:If a dashed line appears in the Hazard Class section for the type of transportation, this indicates the product isnot regulated for transportation.
15 Regulations· SARA Section 355 (extremely hazardous substances)
None of the ingredients is listed.
· SARA Section 313 (specific toxic chemical listings)None of the ingredients is listed.
· TSCA (Toxic Substances Control Act)7732-18-5 water8013-01-2 yeast extract
50-99-7 dextrose113-24-6 sodium pyruvate
73049-73-7 meat peptone52993-95-0 SPS
68-04-2 Sodium citrate16009-13-5 hemin
58-27-5 menadione
· California Proposition 65 - Chemicals known to cause cancerNone of the ingredients is listed.
(Contd. on page 5) USA
Page 5/5Material Safety Data Sheet
acc. to ISO/DIS 11014Date Prepared: 01/07/2010 Reviewed On: 12/21/2007
Product name: BACTEC Lytic/10 Anaerobic/F Culture Vials
(Contd. of page 4)
DR
· California Proposition 65 - Chemicals known to cause reproductive toxicity for females:None of the ingredients is listed.
· California Proposition 65 - Chemicals known to cause reproductive toxicity for males:None of the ingredients is listed.
· California Proposition 65 - Chemicals known to cause developmental toxicity:None of the ingredients is listed.
· Carcinogenic categories· NTP (National Toxicology Program)
None of the ingredients is listed.
· TLV (Threshold Limit Value established by ACGIH)None of the ingredients is listed.
· Product related hazard information:Observe the general safety regulations when handling chemicalsThe product is not subject to identification regulations pertaining to regulations on hazardous materials.
16 Other information:To the best of our knowledge, the information contained herein is accurate. However, neither Becton, Dickinsonand Company or any of its subsidiaries assumes any liabilities whatsoever for the accuracy or completeness ofthe information contained herein. Final determination of suitability of any material is the sole responsibility of theuser. All materials may present unknown hazards and should be used with caution. Although certain hazards aredescribed herein, we can not guarantee that these are the only hazards that exist.
· Department issuing MSDS:Safety and Environment DepartmentMSDS created by Michael J. Spinazzola
· Contact: Technical Service Representative USA
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 1 / 4 VACUETTE® 9NC Coagulation Sodium Citrate 3,2%
AH AA 04.03.02-042 Rev.01Valid from: 03/23/2009
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
• Product Name: VACUETTE® 9NC Coagulation Sodium Citrate 3,2% • Manufacturer/Supplier:
AUSTRIA Greiner Bio-One GmbH Bad Haller Strasse 32 4550 Kremsmünster Austria Tel: (++43) 7583 6791-0 Fax: (++43) 7583 114 Email: [email protected]
USA Greiner Bio-One North America Inc. 4238 Capital Drive Monroe, NC 28110 USA Tel: (++1) 888-286-3883 FAX: (++1) 800-726-0052 Email: [email protected]
BRASIL Greiner Bio-One Brasil Produtos Médicos Hospitalares Ltda. Av. Affonso Pansan no. 1.967 13473-620 Vila Bertini Americana, São Paulo - Brasil Tel: +55 (19) 3468-9600 Fax: +55 (19) 3468-9601 Email: [email protected]
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
• Description: VACUETTE PET Tube (Polyethyleneterephthalate) and optionally Inner PP Tube with • Chemical name: Citric Acid Monohydrate
Citric Acid Trisodium Dihydrate • CAS No. Citric Acid Monohydrate 5949-29-1
Citric Acid Trisodium Dihydrate 6132-04-03 • Quantity of substances: < 10 % • Exposure limits: N/A
SECTION 3: HAZARDS IDENTIFICATION
• Hazard description: My cause eye irritation.
• Acute exposure effect: May cause eye irritation.
SECTION 4: FIRST AID MEASURES
• Skin: Wash with soap and copious amounts of water. • Eyes: Flush eyes with copious amounts of water for at least 15 minutes. Get medical
attention. • Inhalation: Remove to fresh air. If breathing is difficult, get medical attention. • Ingestion: Wash out mouth with water provided person is conscious. Call a physician.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 2 / 4 VACUETTE® 9NC Coagulation Sodium Citrate 3,2%
AH AA 04.03.02-042 Rev.01Valid from: 03/23/2009
SECTION 5: FIRE-FIGHTING MEASURES
• Suitable extinguishing media: Water spray, carbon dioxide, dry chemical powder or appropriate foam.
• Unusual fire and explosion hazards: Emits toxic fumes under fire conditions. This material, like most materials in powder form, is capable of creating a dust explosion.
• Protective equipment: Firefighters should wear proper protective clothing to prevent contact with skin and eyes and self-contained NIOSH approved breathing apparatus operated in positive pressure mode.
SECTION 6: ACCIDENTAL RELEASE MEASURES
• Personal precautions: Avoid overexposure. Wear protective equipment, including NIOSH approved respirator.
• Environmental precautions: N/A • Methods for cleaning up: Do not dry-sweep. Wet down to minimize airborne dust. Place in an
appropriate disposal container. Flush area with water. SECTION 7: HANDLING AND STORAGE
• Handling: Advice for safe handling: Do not breathe dust. Avoid dust generation or accumulation. Use adequate ventilation and dust collection. Information about protection against explosions and fires: N/A
• Storage: Requirements to be met by storerooms and receptacles: Use suitable containers. Keep tightly closed when not in use. Store in a cool, dry, well-ventilated area. Information about storage in one common storage facility: Store away from incompatible materials, such as strong bases and strong oxidizing agents.
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
• Additional information about design of technical systems: Use sufficient local or general exhaust. • Personal protective equipment:
General protective and hygienic measures: Wash thoroughly after handling. Remove contaminated and wash before reuse. Avoid contact with eyes, skin and clothing. Avoid ingestion and inhalation. Use with adequate ventilation. Provide eye bath and safety shower. Breathing equipment: NIOSH-approved respirator Hand protection: Wear appropriate protective gloves to prevent skin exposure. Eye protection: Use chemical safety goggles Body protection: Wear appropriate protective clothing to prevent skin exposure.
• Hygiene measures: N/A SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
• General information Form: Solid Color: White Odor: Odorless
• PH-value: Citric Acid Monohydrate: 1,85 (5%, 25°C) Citric Acid Trisodium Dihydrate: 7,5 – 9,0
• Change in condition Melting point/Melting range: Citric Acid Monohydrate: 135 – 152 °C Citric Acid Trisodium Dihydrate: 300 °C Boiling point/Boiling range: not determined
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 3 / 4 VACUETTE® 9NC Coagulation Sodium Citrate 3,2%
AH AA 04.03.02-042 Rev.01Valid from: 03/23/2009
• Flash point: Citric Acid Monohydrate: 345 °C Citric Acid Trisodium Dihydrate: N/A
• Flammability (solid, gaseous): N/A • Danger of explosion: Product does not present an explosion hazard • Vapor pressure: Not determined • Density: Citric Acid Monohydrate: 1,4 g/cm3
Citric Acid Trisodium Dihydrate: N/A • Solubility in/Miscibility w/H2O: Soluble • Organic solvents: N/A • Solids content: N/A
SECTION 10: STABILITY AND REACTIVITY
• Thermal decomposition / conditions to avoid: None identified • Materials to avoid: Strong bases, strong oxidizing agents and reducing agents. • Dangerous reactions: Stable, none known • Hazardous decomposition products: none identified
SECTION 11: TOXICOLOGICAL INFORMATION
• Acute toxicity (LD 50 oral rat > 200 mg/kg) Eye: May cause irritation Skin: May cause irritation Inhalation: Inhalation of large amounts of dust may be irritating to the upper respiratory tract. Ingestion: May cause nausea and vomiting if ingested in large quantities. May also cause hypernoia and convulsing. Primary irritant effect: On the skin: Not established On the eye: Not established
• Sensitization: Not established • Additional toxicological information: None identified
SECTION 12: ECOLOGICAL INFORMATION
• Ecotoxilogical effects: No data is available on the adverse effects of this material on the environment. • Other information: N/A • General notes: N/A
SECTION 13: DISPOSAL CONSIDERATION
• Product: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. Disposal must be made according to the regulations found in 40 CFR 261. This product is not a hazardous waste according to local regulations.
• Packaging: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. This product is not a hazardous waste according to local regulations. Recommended cleansing agent: Water if necessary with cleansing agents
SECTION 14: TRANSPORT INFORMATION
• DOT regulations: Not regulated • Land transport ADR/RID: Not regulated • Maritime transport IMDG: Not regulated • Air transport ICAO-TI and IATA-DGR: Not regulated
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 4 / 4 VACUETTE® 9NC Coagulation Sodium Citrate 3,2%
AH AA 04.03.02-042 Rev.01Valid from: 03/23/2009
SECTION 15: REGULATORY INFORMATION
• EC directives: 91/155/EEC, 93/112/EC, 88/379/EEC • National regulations: Chemical (Hazard Information and Packaging) Regulations: ChemG
(Austria) • Water hazard class: N/A • Note: Please note that there may be additional legal provisions to be observed. We recommend that
you keep yourself informed about all applicable international, national and local regulations. SECTION 16: OTHER INFORMATION To the best of our knowledge, the information contained herein is accurate. However, neither Greiner Bio-One nor any of its subcontractors or suppliers assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 1 / 4 VACUETTE® LH Lithium Heparin Sep
AH AA 04.03.02-015 Rev.03Valid from: 03/23/2009
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
• Product Name: VACUETTE® LH Lithium Heparin Sep • Manufacturer/Supplier:
AUSTRIA Greiner Bio-One GmbH Bad Haller Strasse 32 4550 Kremsmünster Austria Tel: (++43) 7583 6791-0 Fax: (++43) 7583 114 Email: [email protected]
USA Greiner Bio-One North America Inc. 4238 Capital Drive Monroe, NC 28110 USA Tel: (++1) 888-286-3883 FAX: (++1) 800-726-0052 Email: [email protected]
BRASIL Greiner Bio-One Brasil Produtos Médicos Hospitalares Ltda. Av. Affonso Pansan no. 1.967 13473-620 Vila Bertini Americana, São Paulo - Brasil Tel: +55 (19) 3468-9600 Fax: +55 (19) 3468-9601 Email: [email protected]
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
• Description: VACUETTE PET Tube (Polyethyleneterephthalate) with • Chemical name: Lithium Heparin
Gel (proprietary) • CAS No. Lithium Heparin 9045-22-1
Gel N/A • Quantity of substances: Lithium Heparin < 1%
Gel 10 – 15 % • Exposure limits: N/A
SECTION 3: HAZARDS IDENTIFICATION
• Hazard description: EU: The chemical constituent in this product has not been classified as hazardous under European Directive 91/155/EEC, and 93/112EC. US: Inhalation may cause nosebleeds. Avoid contact.
• Health effects: Acute exposure effect: Inhalation: May cause nosebleeds Repeated Exposure Effects: Inhalation: May cause nosebleeds Primary route of entry: Inhalation Medical conditions which might be aggravated: None identified
• Physical Hazards: Avoid generation and accumulation of dusts.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 2 / 4 VACUETTE® LH Lithium Heparin Sep
AH AA 04.03.02-015 Rev.03Valid from: 03/23/2009
SECTION 4: FIRST AID MEASURES
• Skin: Wash thoroughly with water. • Eyes: Wash thoroughly with water. • Inhalation: Move the exposed person to fresh air. Consult a physician. • After swallowing: Dilute with large amounts of water. Consult a physician. • Information for doctor: Show this label
SECTION 5: FIRE-FIGHTING MEASURES
• Suitable extinguishing media: Water spray; dry chemical; carbon dioxide • Protective equipment: Wear self-contained breathing apparatus and suitable protective clothing.
SECTION 6: ACCIDENTAL RELEASE MEASURES
• Personal precautions: Avoid overexposure. Wear suitable protective clothing. • Environmental precautions: N/A • Methods for cleaning up: If amount is small, wash area with water. If amount is large, material
should be contained in a clean, dry container and covered. Avoid inhalation during cleanup. SECTION 7: HANDLING AND STORAGE
• Handling: Advice for safe handling: Avoid inhalation of dusts. Information about protection against explosions and fires: This material may cause a dust explosion. Avoid dust generation.
• Storage: Requirements to be met by storerooms and receptacles: Product is moisture-sensitive. Store in dark-colored glass or metal containers in a cool, dry place. Information about storage in one common storage facility: N/A
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
• Additional information about design of technical systems: Use local or general ventilation to keep dust levels as low as possible.
• Control parameters: N/A • Personal protective equipment:
General protective and hygienic measures: Wash thoroughly after handling. Remove contaminated and wash before reuse. Avoid contact with eyes, skin and clothing. Avoid ingestion and inhalation. Use with adequate ventilation. Provide eye bath and safety shower. Breathing equipment: Use OSHA-approved particle/dust mask Hand protection: Use sterile gloves. Eye protection: Use safety goggles Body protection: Wear appropriate protective clothing to prevent skin exposure.
• Hygiene measures: N/A
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 3 / 4 VACUETTE® LH Lithium Heparin Sep
AH AA 04.03.02-015 Rev.03Valid from: 03/23/2009
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
• General information Form: Lithium Heparin: Crystalline powder Gel: Paste mixture Color: Lithium Heparin: White Gel: semitransparent, pale yellow, milky white Odor: Almost odorless
• PH-value: N/A • Change in condition
Melting point/Melting range: Not determined Boiling point/Boiling range: Not determined Flash point: N/A
• Flammability (solid, gaseous): N/A • Danger of explosion: Generation and accumulation of dusts may cause an explosion. • Vapor pressure: N/A • Density: not determined • Solubility in/Miscibility w/H2O: Lithium Heparin: Soluble
Gel: Insoluble • Organic solvents: N/A • Specific gravity: N/A
SECTION 10: STABILITY AND REACTIVITY
• Thermal decomposition / conditions to avoid: Avoid generation and accumulation of dusts. • Materials to avoid: None identified. • Dangerous reactions: Stable • Hazardous decomposition products: None identified
SECTION 11: TOXICOLOGICAL INFORMATION
• Acute toxicity (LD 50 oral, rat > 200 mg/kg) Eye: None identified Skin: None identified Inhalation: May cause irritation Ingestion: None identified
• Primary irritant effect: On the skin: Not established On the eye: Not established
• Sensitization: Not established • Additional toxicological information: None identified
SECTION 12: ECOLOGICAL INFORMATION
• Ecotoxilogical effects: No data is available on the adverse effects of this material on the environment. • Other information: N/A • General notes: N/A
SECTION 13: DISPOSAL CONSIDERATION
• Product: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. Disposal must be made according to the regulations found in 40 CFR 261. This product is not a hazardous waste according to local regulations.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 4 / 4 VACUETTE® LH Lithium Heparin Sep
AH AA 04.03.02-015 Rev.03Valid from: 03/23/2009
• Packaging:
Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. Disposal must be made according to the regulations found in 40 CFR 261. This product is not a hazardous waste according to local regulations. Recommend cleansing agent Water, if necessary with cleansing agents
SECTION 14: TRANSPORT INFORMATION
• DOT regulations: Not regulated • Land transport ADR/RID: Not regulated • Maritime transport IMDG: Not regulated • Air transport ICAO-TI and IATA-DGR: Not regulated
SECTION 15: REGULATORY INFORMATION
• EC directives: 91/155/EEC, 93/112/EC, 88/379/EEC • National regulations: Chemical (Hazard Information and Packaging) Regulations: ChemG
(Austria) • Water hazard class: N/A • Note: Please note that there may be additional legal provisions to be observed. We recommend that
you keep yourself informed about all applicable international, national and local regulations. SECTION 16: OTHER INFORMATION To the best of our knowledge, the information contained herein is accurate. However, neither Greiner Bio-One nor any of its subcontractors or suppliers assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
Page 1 of 2
MATERIAL SAFETY DATA SHEET (MSDS)
Product: Polar Pack® Reusable Refrigerant Pack
Date: 10-04-07
SECTION I Identification and Description
Company ThermoSafe Brands, Contact Elizabeth Nichols, Product Manager
a part of Tegrant Corporation Phone 847-632-9648
Address 3930 Ventura Drive, Suite 450 Fax 847-632-0653
Arlington Heights, Illinois 60004 E-mail [email protected]
SECTION II Hazardous Ingredients
Ingredient % TLV Units Solvents % TLV Units
Pigments NA NA
Catalyst NA NA
Vehicle NA NA
Others: rigid, cellular phenolic foam
NA NA
SECTION III Physical Data
Boiling Point: liquid only 203°F / 95°C Specific Gravity 1.15 @ 75°F
Vapor Pressure NA % Volatile by Volume NA
Vapor Density NA Appearance/Odor Clear, odorless gel
Water Soluble 100% Evaporation Rate 4.8
SECTION IV Fire and Explosion Hazard Data
Flash Point NA
Flammable Limits NA
Special Fire Fighting Procedures NA
Unusual fire & Explosion Hazards NA
SECTION V Health Hazard Data
Threshold Limit Value NA
Effects of Overexposure NA
Emergency First Aid Procedures NA
Page 2 of 2
THERMOSAFE BRANDS MATERIAL SAFETY DATA SHEET (MSDS) – page 2
Product: Polar Pack® Reusable Refrigerant Pack
SECTION VI Reactivity Data
Incompatibility (avoid these materials) NA
Hazardous Decomposition Products None
Conditions to Avoid NA
SECTION VII Spill or Leak Procedures
Waste Disposal Method:
Dispose with ordinary solid waste or dilute with water and dispose via sewage system in conformance with federal, state and local regulations.
Steps to be taken if material is spilled or leaked:
Collect as much leaked material as possible; use of sand or other absorbent materials may be helpful. Wash floors and other walking surfaces with water and abrasive cleaners to remove all slippery residues.
SECTION VIII Special Protection Information
Respiratory Protection Not Necessary
Protective Gloves Recommended when handling frozen product; otherwise not necessary.
Eye Protection Not Necessary
Ventilation Not Necessary
Other None
SECTION IX Special Precautions
Precautions to be taken in handling and storing:
NOTE: Careless handling of frozen Polar Pack products may damage the film pouch material, resulting in leakage of the pcm gel during thaw. Before refreezing, examine film material for tears, punctures, etc.
Other precautions: None
Tegrant Corporation ThermoSafe Brands 3930 Ventura Drive, Suite 450 Arlington Heights, IL 60004 www.thermosafe.com (t) 800-323-7442 (f) 847-398-0653
MSDS Polar Pack Reusable Refrigerant Pack 10/04/07 ©2007 ThermoSafe
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 1 / 4 VACUETTE® K3E K3EDTA
AH AA 04.03.02-032 Rev.04Valid from: 03/23/2009
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
• Product Name: VACUETTE® K3E K3EDTA • Manufacturer/Supplier:
AUSTRIA Greiner Bio-One GmbH Bad Haller Strasse 32 4550 Kremsmünster Austria Tel: (++43) 7583 6791-0 Fax: (++43) 7583 114 Email: [email protected]
USA Greiner Bio-One North America Inc. 4238 Capital Drive Monroe, NC 28110 USA Tel: (++1) 888-286-3883 FAX: (++1) 800-726-0052 Email: [email protected]
BRASIL Greiner Bio-One Brasil Produtos Médicos Hospitalares Ltda. Av. Affonso Pansan no. 1.967 13473-620 Vila Bertini Americana, São Paulo - Brasil Tel: +55 (19) 3468-9600 Fax: +55 (19) 3468-9601 Email: [email protected]
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
• Description: VACUETTE PET Tube (Polyethyleneterephthalate) with • Chemical name: Ethylenediaminetetraacetic Acid Tripotassium Dihydrate K3EDTA • CAS No. 65501-24-8 • Quantity of substances: < 1% • Exposure limits: N/A
SECTION 3: HAZARDS IDENTIFICATION
• Hazard description: My cause eye and skin irritation. Causes respiratory tract irritation and gastrointestinal irritation. Avoid generating dust or dust accumulation.
• Acute exposure effect: May cause skin and eye irritation. Inhalation causes respiratory tract irritation. Ingestion causes gastrointestinal irritation with nausea, vomiting and diarrhea.
SECTION 4: FIRST AID MEASURES
• Skin: Wash with soap and copious amounts of water. • Eyes: Flush eyes with copious amounts of water for at least 15 minutes. • Inhalation: Remove to fresh air. If breathing is difficult, give oxygen. • Ingestion: Victim should drink copious amounts of water to dilute. Get medical attention.
SECTION 5: FIRE-FIGHTING MEASURES
• Suitable extinguishing media: Use extinguishing media appropriate for surrounding fire. • Protective equipment: Firefighters should wear proper protective equipment and self-contained
breathing apparatus with full-face piece operated in positive pressure mode.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 2 / 4 VACUETTE® K3E K3EDTA
AH AA 04.03.02-032 Rev.04Valid from: 03/23/2009
SECTION 6: ACCIDENTAL RELEASE MEASURES
• Personal precautions: Avoid overexposure. Wear suitable protective clothing. • Environmental precautions: N/A • Methods for cleaning up: Carefully sweep up and remove. Flush area with water.
SECTION 7: HANDLING AND STORAGE
• Handling: Advice for safe handling: Keep container tightly closed. Suitable for any general chemical storage area. Information about protection against explosions and fires: Avoid contact with incompatible material, minimize dust generation and accumulation.
• Storage: Requirements to be met by storerooms and receptacles: Keep container tightly closed. Information about storage in one common storage facility: Suitable for any general chemical storage area.
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
• Control parameters: N/A • Personal protective equipment:
General protective and hygienic measures: Wash thoroughly after handling. Remove contaminated and wash before reuse. Avoid contact with eyes, skin and clothing. Avoid ingestion and inhalation. Use with adequate ventilation. Respiratory protection: None required, where adequate ventilation conditions exist. If airborne concentration is high, use an appropriate dust mask. Hand protection: Wear proper gloves. Eye protection: Use safety goggles Body protection: Wear appropriate protective clothing to prevent skin exposure.
• Hygiene measures: N/A SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
• General information Form: Crystalline powder Color: White Odor: Odorless
• PH-value: N/A • Change in condition
Melting point/Melting range: not determined Boiling point/Boiling range: not determined
• Flash point: N/A • Flammability (solid, gaseous): N/A • Danger of explosion: Product does not present an explosion hazard • Vapor pressure: Not determined • Density: N/A • Solubility in/Miscibility w/H2O: Soluble • Organic solvents: N/A • Solids content: N/A
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 3 / 4 VACUETTE® K3E K3EDTA
AH AA 04.03.02-032 Rev.04Valid from: 03/23/2009
SECTION 10: STABILITY AND REACTIVITY
• Thermal decomposition / conditions to avoid: No decomposition if used according to specifications.
• Materials to avoid: None identified. • Dangerous reactions: No dangerous reactions known • Hazardous decomposition products: Oxides of nitrogen, carbon monoxide, carbon dioxide.
SECTION 11: TOXICOLOGICAL INFORMATION
• Acute toxicity (LD 50 oral rat > 200 mg/kg) Eye: May cause irritation Skin: May cause irritation Inhalation: May cause irritation Ingestion: Not established Primary irritant effect: On the skin: Not established On the eye: Not established
• Sensitization: Not established • Additional toxicological information: None identified
SECTION 12: ECOLOGICAL INFORMATION
• Ecotoxilogical effects: No data is available on the adverse effects of this material on the environment. • Other information: N/A • General notes: N/A
SECTION 13: DISPOSAL CONSIDERATION
• Product: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. This product is not a hazardous waste according to local regulations.
• Packaging: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. This product is not a hazardous waste according to local regulations.
SECTION 14: TRANSPORT INFORMATION
• DOT regulations: Not regulated • Land transport ADR/RID: Not regulated • Maritime transport IMDG: Not regulated • Air transport ICAO-TI and IATA-DGR: Not regulated
SECTION 15: REGULATORY INFORMATION
• EC directives: 91/155/EEC, 93/112/EC, 88/379/EEC • National regulations: Chemical (Hazard Information and Packaging) Regulations: ChemG
(Austria) • Water hazard class: N/A • Note: Please note that there may be additional legal provisions to be observed. We recommend that
you keep yourself informed about all applicable international, national and local regulations.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 4 / 4 VACUETTE® K3E K3EDTA
AH AA 04.03.02-032 Rev.04Valid from: 03/23/2009
SECTION 16: OTHER INFORMATION To the best of our knowledge, the information contained herein is accurate. However, neither Greiner Bio-One nor any of its subcontractors or suppliers assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
Para-Pak® Ultra Zn-PVA/10% Formalin MSDS Sheet
Product Catalog > Para-Pak® Parasitology Products > Para-Pak® Two-Vial Stool Transport Systems > List of Products > Para-Pak® Ultra Zn-PVA/10% Formalin > MSDS Sheets > MSDS Sheet
MATERIAL SAFETY DATA SHEET Additional Product info
IDENTIFICATIONManufactured for: Meridian Bioscience, Inc. Name: Para-Pak® 10% Formalin
Para-Pak® 10% Formalin ULTRA Catalog#: 900412, 300112, 300812, 301012, 330184,
330284, 331084, 331184, 980412, 380112, 381012
Formula: Mixture CAS#: N/AEPA Hazardous Waste ID #: Formaldehyde EPA Hazardous Waste Class: Formaldehyde T-Toxic Waste HAZARDOUS COMPONENTS
Component % CAS# ACGIH TLV CLASSIFICATION
Formaldehyde 4 50-00-0 0.75ppm TWA 1ppm
PEL
Corrosive, Irritant, Sensitizer, Toxic,
Potential Carcinogen
Methyl Alcohol 1 67-56-1 200ppm TWA
Irritant, Toxic
Mixture not tested as a whole. The mixture is assumed to present the same health hazards as do the components present at >1.0% (0.1% for carcinogens).
PHYSICAL AND CHEMICAL DATAAPPEARANCE: Colorless liquid pH: 7.00 +/- 0.2 ODOR: PungentVAPOR PRESSURE: NDVOLATILE COMPONENTS: NDEVAPORATION RATE: NDSOLUBILITY IN WATER: Unlimited FIRE AND EXPLOSION HAZARD DATAFLASH POINT: >200 ° F EXTINGUISHING MEDIA: Media appropriate for surrounding fire
conditions.FIRE FIGHTING PROCEDURES:
Wear self-contained breathing apparatus and protective clothing.
FIRE HAZARDS: May produce hazardous decomposition products.
Date of Preparation : 8/25/98Revision Date : 7/8/05 IdentificationHazardous Components Physical and Chemical Data Fire and explosion data
file:///C|/Documents%20and%20Settings/hemmendinger...Ultra%20Zn-PVA-10%25%20Formalin%20MSDS%20Sheet.htm (1 of 2)4/15/2009 9:21:11 AM
Para-Pak® Ultra Zn-PVA/10% Formalin MSDS Sheet
REACTIVITY DATASTABILITY: StableINCOMPATIBILITY: Strong oxidizing agents, strong bases.HAZARDOUS POLYMERIZATION:
None
HEALTH HAZARDEXPOSURE LIMITS: NDEXPOSURE EFFECTS:EYE: Irritant SKIN: Irritant INHALATION: Headache, unconsciousness INGESTION: Nausea, vomiting, death FIRST AID DATAFIRST AID: Obtain medical attention EYE: Flush with water for 15 minutes.SKIN: Flush with water for 15 minutes.INHALATION: Removed to fresh air immediately. If breathing stops,
give artificial respiration. INGESTION: Contact a physician immediately to obtain the
appropriate emergency treatment. HANDLING AND STORAGEWear chemical safety goggles, chemical resistant gloves and protective clothing. Use OSHA approved respirator if TLV exceeded. General mechanical ventilation is usually adequate under normal use. Do not exceed TLV. Containers potentially hazardous when empty. Do not reuse. SPILL AND DISPOSAL PROCEDURESSPILL: Absorb on paper, vermiculite, etc.WASTE DISPOSAL: Consult federal, state, and local regulations.
NA = Not Applicable ND = Not Determined
The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. Meridian Bioscience, Inc. shall not be held liable for any damage resulting from handling or from contact with the above product.
© Copyright 2008 Meridian Bioscience, Inc. Meridian Bioscience, Inc. 3471 River Hills Drive, Cincinnati, OH 45244 (513) 271-3700
file:///C|/Documents%20and%20Settings/hemmendinger...Ultra%20Zn-PVA-10%25%20Formalin%20MSDS%20Sheet.htm (2 of 2)4/15/2009 9:21:11 AM
Para-Pak® LV-PVA Bulk MSDS Sheet
Product Catalog > Para-Pak® Parasitology Products > Para-Pak® One-Vial Stool Transport Vial > List of Products > Para-Pak® LV-PVA Bulk > MSDS Sheets > MSDS Sheet
MATERIAL SAFETY DATA SHEET Additional Product info
IDENTIFICATIONManufactured for: Meridian Bioscience, Inc. Name: Para-Pak® LV-PVA Fixative
(Low Viscosity Polyvinyl Alcohol Fixative)
Catalog#: 900112, 300112, 300312, 380112, 338112, 330184, 330284, 400212
Formula: Mixture CAS#: N/AEPA Hazardous Waste ID #: Mercury 0009 EPA Hazardous Waste Class: Mercuric Chloride; EP Toxic waste (E) HAZARDOUS COMPONENTS
Component % CAS# ACGIH TLV CLASSIFICATION
Isopropanol 28 67-63-0 400ppm TWA
Flammable
Acetic Acid 5 64-19-7 10ppm TWA 15ppm STEL
Corrosive
Poly Vinyl Alcohol
5 9002-89-5 ND Irritant
Mercuric Chloride
3.4 7487-94-7 100mg/m 3 (skin) TWA
Corrosive
Glycerol 1.8 56-81-5 ND Irritant
Hydrochloric Acid
1.4 7647-01-0 250ml/in Corrosive
PHYSICAL AND CHEMICAL DATAAPPEARANCE: Colorless liquid pH: ND ODOR: Alcohol VAPOR PRESSURE: NDVOLATILE COMPONENTS: NDEVAPORATION RATE: NDSOLUBILITY IN WATER: Unlimited
Date of Preparation : 1/12/98 Revision Date : 7/12/05 IdentificationHazardous Components Physical and Chemical Data Fire and explosion data
file:///C|/Documents%20and%20Settings/hemmending...SDS/Para-Pak®%20LV-PVA%20Bulk%20MSDS%20Sheet.htm (1 of 3)4/15/2009 9:20:39 AM
Para-Pak® LV-PVA Bulk MSDS Sheet
FIRE AND EXPLOSION HAZARD DATAFLASH POINT: 66 ° F (19 ° C), Boiling point 183 ° F (84 ° C) EXTINGUISHING MEDIA: Media appropriate for surrounding fire
conditions.FIRE FIGHTING PROCEDURES:
Wear self-contained breathing apparatus and protective clothing.
FIRE HAZARDS: May produce hazardous decomposition products.
REACTIVITY DATASTABILITY: StableINCOMPATIBILITY: Strong oxidizing agents, strong bases. HAZARDOUS POLYMERIZATION:
None
HEALTH HAZARDEXPOSURE LIMITS: NDEXPOSURE EFFECTS:EYE: Irritant, burning sensation SKIN: Irritation INHALATION: Coughing, wheezing, laryngitis, shortness of breath,
headache INGESTION: Nausea, vomiting, pain, death FIRST AID DATAFIRST AID: Obtain medical attention. EYE: Flush with water for 15 minutes.SKIN: Flush with water for 15 minutes.INHALATION: Remove to fresh air immediately. If breathing stops, give
artificial respiration. INGESTION: Contact a physician immediately to obtain the
appropriate emergency treatment. HANDLING AND STORAGEWear chemical safety goggles, chemical resistant gloves and protective clothing. Use OSHA approved respirator if TLV exceeded. General mechanical ventilation is usually adequate under normal use. Do not exceed TLV. Containers potentially hazardous when empty. Do not reuse. SPILL AND DISPOSAL PROCEDURESSPILL: Absorb on paper, vermiculite, etc.WASTE DISPOSAL: Consult federal, state, and local regulations.
file:///C|/Documents%20and%20Settings/hemmending...SDS/Para-Pak®%20LV-PVA%20Bulk%20MSDS%20Sheet.htm (2 of 3)4/15/2009 9:20:39 AM
Para-Pak® LV-PVA Bulk MSDS Sheet
TRANSPORTATION INFORMATIONDOT Flammable Liquid, Corrosive, n.o.s., UN2924, Hazard
Class 3, Pkg. Group II, Technical Name: (Contains Isopropanol, Acetic Acid).
IATA Flammable Liquid, Corrosive, n.o.s., UN2924, Hazard Class 3, Pkg. Group II, Technical Name: (Contains Isopropanol, Acetic Acid).
Note 1 – Per 49 CFR – when shipping 30ml or less per inner packaging and the gross weight does not exceed 64lbs. use the 173.4 small quantity exception.
Note 2 – Per catalog #400212 – 5 liters is the maximum volume that can be shipped per package on a cargo aircraft.
NA = Not Applicable ND = Not Determined
The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. Meridian Bioscience, Inc. shall not be held liable for any damage resulting from handling or from contact with the above product.
© Copyright 2008 Meridian Bioscience, Inc. Meridian Bioscience, Inc. 3471 River Hills Drive, Cincinnati, OH 45244 (513) 271-3700
file:///C|/Documents%20and%20Settings/hemmending...SDS/Para-Pak®%20LV-PVA%20Bulk%20MSDS%20Sheet.htm (3 of 3)4/15/2009 9:20:39 AM
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 1 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
• Product Name: VACUETTE® NH Trace Elements Sodium Heparin • Manufacturer/Supplier:
AUSTRIA Greiner Bio-One GmbH Bad Haller Strasse 32 4550 Kremsmünster Austria Tel: (++43) 7583 6791-0 Fax: (++43) 7583 114 Email: [email protected]
USA Greiner Bio-One North America Inc. 4238 Capital Drive Monroe, NC 28110 USA Tel: (++1) 888-286-3883 FAX: (++1) 800-726-0052 Email: [email protected]
BRASIL Greiner Bio-One Brasil Produtos Médicos Hospitalares Ltda. Av. Affonso Pansan no. 1.967 13473-620 Vila Bertini Americana, São Paulo - Brasil Tel: +55 (19) 3468-9600 Fax: +55 (19) 3468-9601 Email: [email protected]
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
• Description: VACUETTE PET Tube (Polyethyleneterephthalate) with • Chemical name: Sodium Heparin • CAS No. 9041-08-1 • Quantity of substances: < 1% • Exposure limits: N/A
SECTION 3: HAZARDS IDENTIFICATION
• Hazard description: EU: The chemical constituent in this product has not been classified as hazardous under European Directive 91/155/EEC, and 93/112EC. US: Inhalation may cause nosebleeds. Avoid contact.
• Health effects: Acute exposure effect: Inhalation: May cause nosebleeds Repeated Exposure Effects: Inhalation: May cause nosebleeds Primary route of entry: Inhalation Medical conditions which might be aggravated: None identified
• Physical Hazards: Avoid generation and accumulation of dusts.
SECTION 4: FIRST AID MEASURES
• Skin: Wash thoroughly with water. • Eyes: Wash thoroughly with water. • Inhalation: Move the exposed person to fresh air. Consult a physician. • After swallowing: Dilute with large amounts of water. • Information for doctor: Show this label
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 2 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 5: FIRE-FIGHTING MEASURES
• Suitable extinguishing media: Water spray; dry chemical; carbon dioxide • Protective equipment: Wear self-contained breathing apparatus and suitable protective clothing.
SECTION 6: ACCIDENTAL RELEASE MEASURES
• Personal precautions: Avoid overexposure. Wear suitable protective clothing. • Environmental precautions: N/A • Methods for cleaning up: If amount is small, wash area with water. If amount is large, material
should be contained in a clean, dry container and covered. Avoid inhalation during cleanup. SECTION 7: HANDLING AND STORAGE
• Handling: Advice for safe handling: Keep container tightly closed. Avoid inhalation of dusts. Information about protection against explosions and fires: This material may cause a dust explosion. Avoid dust generation.
• Storage: Requirements to be met by storerooms and receptacles: Product is moisture-sensitive. Store in dark-colored glass or metal containers in a cool, dry place. Information about storage in one common storage facility: N/A
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
• Additional information about design of technical systems: Use local or general ventilation to keep dust levels as low as possible.
• Control parameters: N/A • Personal protective equipment:
General protective and hygienic measures: Wash thoroughly after handling. Remove contaminated and wash before reuse. Avoid contact with eyes, skin and clothing. Avoid ingestion and inhalation. Use with adequate ventilation. Provide eye bath and safety shower. Breathing equipment: Use OSHA-approved particle/dust mask Hand protection: Use sterile gloves. Eye protection: Use safety goggles Body protection: Wear appropriate protective clothing to prevent skin exposure.
• Hygiene measures: N/A SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
• General information Form: Crystalline powder Color: White Odor: Odorless
• PH-value: N/A • Change in condition
Melting point/Melting range: Not determined Boiling point/Boiling range: Not determined Flash point: N/A
• Flammability (solid, gaseous): N/A • Danger of explosion: Generation and accumulation of dusts may cause an explosion. • Vapor pressure: N/A • Density: Not determined • Solubility in/Miscibility w/H2O: Soluble • Organic solvents: N/A • Specific gravity: N/A
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 3 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 10: STABILITY AND REACTIVITY
• Thermal decomposition / conditions to avoid: Avoid generation and accumulation of dusts. • Materials to avoid: None identified. • Dangerous reactions: Stable • Hazardous decomposition products: None identified
SECTION 11: TOXICOLOGICAL INFORMATION
• Acute toxicity (LD 50 oral rat > 200 mg/kg) Eye: None identified Skin: None identified Inhalation: May cause irritation Ingestion: None identified
• Primary irritant effect: On the skin: Not established On the eye: Not established
• Sensitization: Not established • Additional toxicological information: None identified
SECTION 12: ECOLOGICAL INFORMATION
• Ecotoxilogical effects: No data is available on the adverse effects of this material on the environment. • Other information: N/A • General notes: N/A
SECTION 13: DISPOSAL CONSIDERATION
• Product: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. Disposal must be made according to the regulations found in 40 CFR 261. This product is not a hazardous waste according to local regulations.
• Packaging: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. Disposal must be made according to the regulations found in 40 CFR 261. This product is not a hazardous waste according to local regulations. Recommend cleansing agent Water, if necessary with cleansing agents
SECTION 14: TRANSPORT INFORMATION
• DOT regulations: Not regulated • Land transport ADR/RID: Not regulated • Maritime transport IMDG: Not regulated • Air transport ICAO-TI and IATA-DGR: Not regulated
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 4 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 15: REGULATORY INFORMATION
• EC directives: 91/155/EEC, 93/112/EC, 88/379/EEC • National regulations: Chemical (Hazard Information and Packaging) Regulations: ChemG
(Austria) • Water hazard class: N/A • Note: Please note that there may be additional legal provisions to be observed. We recommend that
you keep yourself informed about all applicable international, national and local regulations. SECTION 16: OTHER INFORMATION To the best of our knowledge, the information contained herein is accurate. However, neither Greiner Bio-One nor any of its subcontractors or suppliers assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 1 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
• Product Name: VACUETTE® NH Trace Elements Sodium Heparin • Manufacturer/Supplier:
AUSTRIA Greiner Bio-One GmbH Bad Haller Strasse 32 4550 Kremsmünster Austria Tel: (++43) 7583 6791-0 Fax: (++43) 7583 114 Email: [email protected]
USA Greiner Bio-One North America Inc. 4238 Capital Drive Monroe, NC 28110 USA Tel: (++1) 888-286-3883 FAX: (++1) 800-726-0052 Email: [email protected]
BRASIL Greiner Bio-One Brasil Produtos Médicos Hospitalares Ltda. Av. Affonso Pansan no. 1.967 13473-620 Vila Bertini Americana, São Paulo - Brasil Tel: +55 (19) 3468-9600 Fax: +55 (19) 3468-9601 Email: [email protected]
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
• Description: VACUETTE PET Tube (Polyethyleneterephthalate) with • Chemical name: Sodium Heparin • CAS No. 9041-08-1 • Quantity of substances: < 1% • Exposure limits: N/A
SECTION 3: HAZARDS IDENTIFICATION
• Hazard description: EU: The chemical constituent in this product has not been classified as hazardous under European Directive 91/155/EEC, and 93/112EC. US: Inhalation may cause nosebleeds. Avoid contact.
• Health effects: Acute exposure effect: Inhalation: May cause nosebleeds Repeated Exposure Effects: Inhalation: May cause nosebleeds Primary route of entry: Inhalation Medical conditions which might be aggravated: None identified
• Physical Hazards: Avoid generation and accumulation of dusts.
SECTION 4: FIRST AID MEASURES
• Skin: Wash thoroughly with water. • Eyes: Wash thoroughly with water. • Inhalation: Move the exposed person to fresh air. Consult a physician. • After swallowing: Dilute with large amounts of water. • Information for doctor: Show this label
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 2 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 5: FIRE-FIGHTING MEASURES
• Suitable extinguishing media: Water spray; dry chemical; carbon dioxide • Protective equipment: Wear self-contained breathing apparatus and suitable protective clothing.
SECTION 6: ACCIDENTAL RELEASE MEASURES
• Personal precautions: Avoid overexposure. Wear suitable protective clothing. • Environmental precautions: N/A • Methods for cleaning up: If amount is small, wash area with water. If amount is large, material
should be contained in a clean, dry container and covered. Avoid inhalation during cleanup. SECTION 7: HANDLING AND STORAGE
• Handling: Advice for safe handling: Keep container tightly closed. Avoid inhalation of dusts. Information about protection against explosions and fires: This material may cause a dust explosion. Avoid dust generation.
• Storage: Requirements to be met by storerooms and receptacles: Product is moisture-sensitive. Store in dark-colored glass or metal containers in a cool, dry place. Information about storage in one common storage facility: N/A
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
• Additional information about design of technical systems: Use local or general ventilation to keep dust levels as low as possible.
• Control parameters: N/A • Personal protective equipment:
General protective and hygienic measures: Wash thoroughly after handling. Remove contaminated and wash before reuse. Avoid contact with eyes, skin and clothing. Avoid ingestion and inhalation. Use with adequate ventilation. Provide eye bath and safety shower. Breathing equipment: Use OSHA-approved particle/dust mask Hand protection: Use sterile gloves. Eye protection: Use safety goggles Body protection: Wear appropriate protective clothing to prevent skin exposure.
• Hygiene measures: N/A SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
• General information Form: Crystalline powder Color: White Odor: Odorless
• PH-value: N/A • Change in condition
Melting point/Melting range: Not determined Boiling point/Boiling range: Not determined Flash point: N/A
• Flammability (solid, gaseous): N/A • Danger of explosion: Generation and accumulation of dusts may cause an explosion. • Vapor pressure: N/A • Density: Not determined • Solubility in/Miscibility w/H2O: Soluble • Organic solvents: N/A • Specific gravity: N/A
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 3 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 10: STABILITY AND REACTIVITY
• Thermal decomposition / conditions to avoid: Avoid generation and accumulation of dusts. • Materials to avoid: None identified. • Dangerous reactions: Stable • Hazardous decomposition products: None identified
SECTION 11: TOXICOLOGICAL INFORMATION
• Acute toxicity (LD 50 oral rat > 200 mg/kg) Eye: None identified Skin: None identified Inhalation: May cause irritation Ingestion: None identified
• Primary irritant effect: On the skin: Not established On the eye: Not established
• Sensitization: Not established • Additional toxicological information: None identified
SECTION 12: ECOLOGICAL INFORMATION
• Ecotoxilogical effects: No data is available on the adverse effects of this material on the environment. • Other information: N/A • General notes: N/A
SECTION 13: DISPOSAL CONSIDERATION
• Product: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. Disposal must be made according to the regulations found in 40 CFR 261. This product is not a hazardous waste according to local regulations.
• Packaging: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. Disposal must be made according to the regulations found in 40 CFR 261. This product is not a hazardous waste according to local regulations. Recommend cleansing agent Water, if necessary with cleansing agents
SECTION 14: TRANSPORT INFORMATION
• DOT regulations: Not regulated • Land transport ADR/RID: Not regulated • Maritime transport IMDG: Not regulated • Air transport ICAO-TI and IATA-DGR: Not regulated
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 4 / 4
VACUETTE® NH Trace Elements Sodium Heparin
AH AA 04.03.02-087 Rev.03Valid from: 03/23/2009
SECTION 15: REGULATORY INFORMATION
• EC directives: 91/155/EEC, 93/112/EC, 88/379/EEC • National regulations: Chemical (Hazard Information and Packaging) Regulations: ChemG
(Austria) • Water hazard class: N/A • Note: Please note that there may be additional legal provisions to be observed. We recommend that
you keep yourself informed about all applicable international, national and local regulations. SECTION 16: OTHER INFORMATION To the best of our knowledge, the information contained herein is accurate. However, neither Greiner Bio-One nor any of its subcontractors or suppliers assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 1 / 4 VACUETTE® K2E K2EDTA Sep
AH AA 04.03.02-031 Rev.03Valid from: 03/23/2009
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
• Product Name: VACUETTE® K2E K2EDTA Sep • Manufacturer/Supplier:
AUSTRIA Greiner Bio-One GmbH Bad Haller Strasse 32 4550 Kremsmünster Austria Tel: (++43) 7583 6791-0 Fax: (++43) 7583 114 Email: [email protected]
USA Greiner Bio-One North America Inc. 4238 Capital Drive Monroe, NC 28110 USA Tel: (++1) 888-286-3883 FAX: (++1) 800-726-0052 Email: [email protected]
BRASIL Greiner Bio-One Brasil Produtos Médicos Hospitalares Ltda. Av. Affonso Pansan no. 1.967 13473-620 Vila Bertini Americana, São Paulo - Brasil Tel: +55 (19) 3468-9600 Fax: +55 (19) 3468-9601 Email: [email protected]
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
• Description: VACUETTE PET Tube (Polyethyleneterephthalate) with • Chemical name: Ethylendiaminetetraacetic Acid Dipotassium Dihydrate K2EDTA
Gel (proprietary) • CAS No. K2EDTA 25102-12-9
Gel N/A • Quantity of substances: K2EDTA < 1%
Gel 10 – 15 % • Exposure limits: N/A
SECTION 3: HAZARDS IDENTIFICATION
• Hazard description: My cause eye and skin irritation. Causes respiratory tract irritation and gastrointestinal irritation. Avoid generating dust or dust accumulation.
• Acute exposure effect: May cause skin and eye irritation. Inhalation causes respiratory tract irritation. Ingestion causes gastrointestinal irritation with nausea, vomiting and diarrhea.
SECTION 4: FIRST AID MEASURES
• Skin: Wash with soap and copious amounts of water. • Eyes: Flush eyes with copious amounts of water for at least 15 minutes. • Inhalation: Remove to fresh air. If breathing is difficult, give oxygen. • Ingestion: Victim should drink copious amounts of water to dilute. Get medical attention.
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 2 / 4 VACUETTE® K2E K2EDTA Sep
AH AA 04.03.02-031 Rev.03Valid from: 03/23/2009
SECTION 5: FIRE-FIGHTING MEASURES
• Suitable extinguishing media: Use extinguishing media appropriate for surrounding fire. • Protective equipment: Firefighters should wear proper protective equipment and self-contained
breathing apparatus with full-face piece operated in positive pressure mode. SECTION 6: ACCIDENTAL RELEASE MEASURES
• Personal precautions: Avoid overexposure. Wear suitable protective clothing. • Environmental precautions: N/A • Methods for cleaning up: Carefully sweep up and remove. Flush area with water.
SECTION 7: HANDLING AND STORAGE
• Handling: Advice for safe handling: Keep container tightly closed. Suitable for any general chemical storage area. Information about protection against explosions and fires: Avoid contact with incompatible material, minimize dust generation and accumulation..
• Storage: Requirements to be met by storerooms and receptacles: Keep container tightly closed. Information about storage in one common storage facility: Suitable for any general chemical storage area.
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
• Control parameters: N/A • Personal protective equipment:
General protective and hygienic measures: Wash thoroughly after handling. Remove contaminated and wash before reuse. Avoid contact with eyes, skin and clothing. Avoid ingestion and inhalation. Use with adequate ventilation. Respiratory protection: None required, where adequate ventilation conditions exist. If airborne concentration is high, use an appropriate dust mask. Hand protection: Wear proper gloves. Eye protection: Use safety goggles Body protection: Wear appropriate protective clothing to prevent skin exposure.
• Hygiene measures: N/A SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
• General information Form: K2EDTA Crystalline powder Gel Paste mixture Color: EDTA K2 white Gel semitransparent, pale yellow, milky white Odor: Almost odorless
• PH-value: N/A • Change in condition
Melting point/Melting range: 255 – 280 °C Boiling point/Boiling range: not determined
• Flash point: N/A • Flammability (solid, gaseous): N/A • Danger of explosion: Product does not present an explosion hazard • Vapor pressure: Not determined • Density: N/A
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 3 / 4 VACUETTE® K2E K2EDTA Sep
AH AA 04.03.02-031 Rev.03Valid from: 03/23/2009
• Solubility in/Miscibility w/H2O: K2EDTA soluble
Gel insoluble • Organic solvents: N/A • Solids content: N/A
SECTION 10: STABILITY AND REACTIVITY
• Thermal decomposition / conditions to avoid: No decomposition if used according to specifications.
• Materials to avoid: None identified. • Dangerous reactions: No dangerous reactions known • Hazardous decomposition products: Oxides of nitrogen, carbon monoxide, carbon dioxide.
SECTION 11: TOXICOLOGICAL INFORMATION
• Acute toxicity (LD 50 oral rat > 200 mg/kg) Eye: May cause irritation Skin: May cause irritation Inhalation: Causes respiratory tract irritation Ingestion: Causes digestive tract irritation
• Primary irritant effect: On the skin: Not established On the eye: Not established
• Sensitization: Not established • Additional toxicological information: None identified
SECTION 12: ECOLOGICAL INFORMATION
• Ecotoxilogical effects: No data is available on the adverse effects of this material on the environment. • Other information: N/A • General notes: N/A
SECTION 13: DISPOSAL CONSIDERATION
• Product: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. This product is not a hazardous waste according to local regulations.
• Packaging: Recommendation Disposal should be done in accordance with all federal, state and local environmental regulations. This product is not a hazardous waste according to local regulations.
SECTION 14: TRANSPORT INFORMATION
• DOT regulations: Not regulated • Land transport ADR/RID: Not regulated • Maritime transport IMDG: Not regulated • Air transport ICAO-TI and IATA-DGR: Not regulated
MATERIAL SAFETY DATA SHEET acc. to ISO 11014
Page 4 / 4 VACUETTE® K2E K2EDTA Sep
AH AA 04.03.02-031 Rev.03Valid from: 03/23/2009
SECTION 15: REGULATORY INFORMATION
• EC directives: 91/155/EEC, 93/112/EC, 88/379/EEC • National regulations: Chemical (Hazard Information and Packaging) Regulations: ChemG
(Austria) • Water hazard class: N/A • Note: Please note that there may be additional legal provisions to be observed. We recommend that
you keep yourself informed about all applicable international, national and local regulations. SECTION 16: OTHER INFORMATION To the best of our knowledge, the information contained herein is accurate. However, neither Greiner Bio-One nor any of its subcontractors or suppliers assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.