Marley Eternit Lincoln Clay Pantile Brochure

CI/SfB (47) Ng2

March 2016

LincolnClay pantiles

2 Lincoln clay pantiles

Lincoln combines the bold and beautiful curves of traditional clay pantiles with all the installation simplicity and speed required for today’s roofs.

This means that Lincoln affords the rich appeal of natural, clay pantiled roofs, a thin leading edge and a beauty that matures over time.

As well as quick and easy installation, Lincoln can be installed to meet the latest fixing requirements of BS 5534 and the NHBC technical standards, without compromising tradition.

Lincoln clay pantiles

All factories certified to ISO 9001, ISO 14001

Lincoln pantiles are available with a comprehensive range of clay fittings and accessories to give a traditional finish. Additionally, many of these components can be combined with our Universal range of accessories and fittings to offer a complete dry fix and maintenance-free solution.

For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 3

For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 54 Lincoln clay pantiles

Lincoln Rustic RedSemi-sanded finish

Lincoln Natural RedSmooth finish


Tile features and technical data

Lincoln key features> traditional profile> easy to install (open-gauge design)> low minimum pitch 17.5°> BS 5534 compatible

Key Raised and protected blind nail hole

Raised and protected head and side locks

SoloFix clip recess

Extended weather bars over the roll for low pitch protection

Wide channel for water run-off

Raised ridge to guard against wind-driven rain

Open-gauge design for a flexible fit

Traditional s-curve profile

Thin leading edge

Hidden/cloaked interlock

The Lincoln clay pantile features a completely open-gauge design, making it quick and easy to install.For full technical data and advice, please contact our Technical Advisory Service on 01283 722588

A

D

B

E

C

Key SoloFix clip ‘pocket’ for a flush fit

Batten locator to avoid rocking

Deep nibs for ease of setting out and fixing

Double anti-capillary bars to prevent water ingress

K

N

L

ML

M

F

G

H

I

I

J

Technical dataSize of tile 370 x 247mm

Minimum pitch* 17.5° (120mm headlap) 22.5° (75mm headlap)

Maximum pitch 70°

Minimum headlap 75mm

Maximum gauge 295mm

Cover width 222mm (nominal)

Covering capacity 15.3 tiles/m2 at 75mm headlap (net) 18.0 tiles/m2 at 120mm headlap

Weight of tiling 43.0 kg/m2 at 75mm headlap (approx.) 50.4 kg/m2 at 120mm headlap

Battens required 3.4 lin.m/m2 at 75mm headlap (net) (net) 4.0 lin.m/m2 at 120mm headlap (net)

Batten size 38 x 25mm for rafters/supports recommended not exceeding 450mm centres (fixed to BS 5534) 50 x 25mm for rafters/supports not exceeding 600mm centres

Tile nails 38 x 3.35mm

Fixing clips Eaves, verge and tile clips

Authority BS EN 1304

* The minimum recommended pitch and lap may be influenced by special circumstances, please contact the Technical Advisory Service.

370

247

A

B

DE

F

C G

J

H

K

N

375

80

240


Half round ridge tile

Third round hip tile Third round hip end tile

Left hand verge tile

Dentil slip

Half round ridge end tile

Ventilation tile

Lincolnclay fittings and accessories

• Universal HipFast system (6m)

• Universal HipFast support tray (6m)

• RidgeFast/HipFast union pack (6 No. unions)

• Universal 10mm eaves vent system (6m)

• Universal 25mm eaves vent system (6m)

• Comb filler strip

• Continuous rafter roll (2 x 6 m)

• Gutter spacers (20 per pack)

• Lead support strip (1.5m)

• Dry ridge batten section (3m)

• Dry ridge batten section (3m)

• Lincoln filler unit vented

• High profile GRP valley trough (3m)

• Accommodates up to 20° pitch difference either side of valley

• Suitable on rafter pitches from 17.5° to 60°

• Universal RidgeFast system (6m)

• RidgeFast blanking tape (2 x 2 m)

• RidgeFast/HipFast union pack (6 No. unions)

Dry fix ventilation and accessoriesThe following products and accessories can be used with Lincoln clay fittings. Our website also contains further information about dry fix and ventilation solutions: www.marleyeternit.co.uk/dryfix Note: Minimum and maximum pitches may vary – please contact our Technical Advisory Service for more information.

Universal eaves vent system

Top abutment ventilation systemUniversal GRP dry valley

Universal RidgeFast system Universal HipFast system

• Mortar bedded security hip kit

• Watch a quick video on mortar bedded security fixing at marleyeternit.co.uk/securityhip or scan the QR code shown

• Mortar bedded security ridge kit

• Watch a quick video on mortar bedded security fixing at marleyeternit.co.uk/securityridge or scan the QR code shown

Security fixingMortar bedded security ridge and hip fixing kits are available to meet the latest British Standards and NHBC guidelines.Note: Minimum and maximum pitches may vary – please contact our Technical Advisory Service for more information.

Mortar bedded security ridge Mortar bedded security hip

375

120

270

370

247

370

247

90

150

385

120

270

80

385

240

All dimensions in mm.


LincolnDesign detailing

Universal eaves ventilation> eaves ventilation to satisfy 10mm or 25mm conditions

> eaves to ridge ventilation for pitches of 17.5°-70°

> continuous rafter roll compresses insulation to allow free air passage (use two rolls to compress deep insulation)

> strip ventilator has discreet ventilation grille and is nailed to fascia or timber fillet

> suitable with or without soffit board

> use comb filler strip with deep profiled tiles

> mechanically fix all tiles at eaves

Lincoln clay pantile

10/25mm over fasciastrip ventilator

Continuous rafterroll (2 No.)

Maximum gauge 295mm

Tiling fillet

Bedded verges> ensure undercloak does not tilt towards gable

> verge overhang should be a maximum of 50mm

> use Lincoln left hand verge tile for left hand verges

> mechanically fix all verge tiles in accordance with BS 5534

Lincoln verge clip

Fibre cement undercloak

Tiling batten

Underlay


Mortar bedding

Third round hip tile

Ridge union clamp

Ridge union

Ridge roll flashing


Ridge batten bracket

Hip batten brackets

Mortar bedded hips> maximum rafter pitch 45°

> fix hip units to hip tree using ridge clamp and 100mm stainless steel screw

> complete hip at ridge apex with three way mitre

Universal HipFast system> provides additional ventilation to the roof void when a 5mm gap in the underlay is used in conjunction with either eaves or ridge ventilated systems or ventilation tiles

> use one or two thicknesses of 50mm x 25mm batten to fit batten brackets

> use hip end hip tile at eaves

> mechanically fix each hip tile via hip unions and clamps

> complete hip at ridge with soaker flashing

For more information on security hip fixing kits, including installation videos, you can scan the QR code or visit: marleyeternit.co.uk/securityhip

Tiling batten

Underlay

Lincoln clay pantileLincoln left hand verge tile

Fibre cement undercloak

Lincoln verge clip

Mortar bedding


Universal GRP dry valley> minimum rafter pitch 17.5°, maximum 60°

> maximum valley length 8m

> suitable for all plan angles and where the pitch either side of the valley varies by a maximum of 20°

> provide continuous support for valley trough using 19mm timber ply boards inset between rafters or 6mm continuous ply boards laid over rafters

> tightly butt tiles or slates to central upstand of valley units to prevent ingress of birds or vermin

> provide metal apron at foot of valley and dress into gutter at eaves. For rafter pitches below 25° cut fascia board to maintain valley pitch

> nail or clip adjacent tiles to the valley

> complete top of valley with a lead saddle

Battens at max 295mm gauge Lincoln clay pantiles cut to angle of valley


Underlay

Rafter

19mm (min) timber valley board

High profile dry valley trough

Tiling batten

Design detailing

Universal RidgeFast system> provides 5,000mm2/m free vent area at ridge apex

> ensure gap is provided in roof underlay to vent roof void

> use one or two thicknesses of 50mm x 25mm batten to fit

batten brackets

> mechanically fix all top course tiles

> use ridge end tile

Half round ridge tile

Ridge union clamp

Ridge union

Ridge roll flashing


Ridge batten bracket

Underlay cut to provide insulation

Mortar bedded ridges> security ridge fixing kits are available for Lincoln clay ridges

> maximum rafter pitch 50°

> fix ridge units to ridge batten using ridge clamp and 100mm stainless steel screw

> mechanically fixes ridge tile in line with BS 5534 fixing guidelines

For more information on security ridge fixing kits, including installation videos, you can scan the QR code or visit: marleyeternit.co.uk/securityridge

14 Lincoln clay pantiles

Resources

Technical adviceOur Technical Advisory Service is staffed by a qualified team with specialist knowledge. Call 01283 722588 or e-mail [email protected]

Fixing instructions and literature Comprehensive sitework, fixing and installation literature and videos: marleyeternit.co.uk/resources

All current product and technical literature can be downloaded: marleyeternit.co.uk/downloads

SamplesSamples of clay interlocking and plain tiles, fibre cement slates and concrete tiles are available on request. Tel 01283 722588 marleyeternit.co.uk/samples

Stockist informationTo find details for stockists of Marley Eternit products, visit: marleyeternit.co.uk/stockists

Customer servicesKnowledgeable and friendly staff are available to offer quotations, expert advice, deal with orders and all other enquiries. Call 08705 626400 or e-mail [email protected]

Sales supportOur Area Sales Managers have in-depth knowledge of your local area. They are available to visit your site to carry out a roof survey, and to offer specific solutions for both new build and refurbishment projects. marleyeternit.co.uk/localcontacts

TilefixTo request a fixing specification based on the geographical location and building dimensions of specific building projects. Call 01283 722588 or e-mail [email protected]

EstimatorTo request a complete bill of materials for your roofing project: Call 01283 722588 or e-mail [email protected]

Training centreWe have a purpose-built training centre where we are able to impart our expertise through a range of practical and classroom courses. To find out more about our courses, visit: marleyeternit.co.uk/training

Health and SafetyIn line with the requirements of the Health and Safety at Work Act, The Consumer Protection Act and The Chemicals (Hazard Information and Packaging for Supply) Regulations and the Control of Substances Hazardous to Health Regulations, please download and view copies of our COSHH data sheets at marleyeternit.co.uk/coshh

Design detailing

Abutment> maximum rafter pitch 45° (55° using steep pitch batten section)

> provides 5,000mm2/lin.m ventilation

> ensure air passage from roof void is not obstructed

> mechanically fix all top course tiles

> use minimum 1.5m length of lead flashing with 150mm side laps

Underlay

Code 4 lead

Lead support strip

Lincoln ventilatedfiller unit


Dry ridgebatten section

Underlay cut back5mm min. to provideventilation

Min.75mm

Batten

Lincoln clay tile vent> locate clear of rafters

> use spigot-soaker tray to weather the offset hole in underlay

> locate at 1.3-1.5m centres for 5,000mm2/lin.m ventilation and 565-765mm centres for 10,000mm2/lin.m ventilation

Underlay

Nailed fixing to back of batten

‘V’ cut in felt with flap nailed to batten

Battens at max. 295mm gauge


Lincoln clay tile vent

50mm air gap maintained over insulation

For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 15

Call 01283 722588 Email [email protected] Or visit www.marleyeternit.co.uk

Marley Eternit Lichfield Road Branston Burton upon Trent DE14 3HD

Documents

Marley Eternit Lincoln Clay Pantile Brochure