Embed Size (px)
Yanmar Asia（Singapore）Corp. Pte. Ltd.4 Tuas Lane, S ingapore 638613Tel : 65-6861-3855 Fax : 65-6862-5195
Yanmar Europe B.V.Brugple in 11, 1332 BS Almere -de Vaart , The Netherl andsTel : 31-36-5493200 Fax : 31-36-5493209
Yanmar Marine U.S.A. Corp.101 Internat ional Pa rkway, Ada i rsv ille, GA 30103, U.S. A.Tel : 1-770-877-9894 Fax : 1-770-877-9009
Yanmar Engine（Shanghai）Co., Ltd.18F, North Tower, Shanghai Stock Exchange Bu ild ing, 528 South Pudong Road, Pudong Shanghai, China, P.C.（200120）Tel : 86-21-6880-5090 Fax : 86-21-6880-8090
Yanmar Marine System Co., Ltd.5-3-1, Tsukaguchi-honmachi, Amagasaki, Hyogo, JapanTel : 81-6-7711-6405 Fax : 81-6-6428-0485
Yanmar Co., Ltd.1-32, Chayamachi, Kit a-ku, Osaka, Japan
Note: All data subject to alterat ion without not ice. Photograph may show opt ional equipment.
MARINE DIESEL ENGINEPRODUCT GU IDE
Rating definit ions:hp=0.7355kW Ratings are based on condit ions of 100kPa, 30% relat ivehumidity at 25°C.S=For applicat ions where use of rated power is less than 30 minutes continuous.L=For applicat ions where use of rated power is less than 2 hours continuous.M=For applicat ions where use of rated power is less than 10 hours continuous.H=For applicat ions where use of rated power is less than 24 hours continuous.Fuel rates: Specif ic gravity 0.835g/cc, low calorif ic value 42700kj/kg(10200kcal/kg), Cetane No.45.
..
001M0-G00390 0904 H
MARINE PROPULSION
DIESEL ENGINE
[ 2 ] [ 3 ]
Reliability, Economical efficiency & Comfortfor customersdedicated tomaritime activity.
Our pride is to contribute to
tough and valuable activities
of customers on the sea.
• Pre-combustion chamber. Two cylinders.• 2GMY is equipped with mechanical marine gear.
• 4-cylinder, direct injection, heat exchanger cooling.• Natural aspiration.• Yanmar YX marine gear is standerd.
[ 4 ] [ 5 ]
SpecificationsModelNumber of cylindersBore × strokeDisplacementRated output
Combution systemAspirationStarting systemCooling systemMarine gearDry massDimensions (L×W×H)
mm
lit .
kW (hp) /rpm
kg
mm
2GMY2 in-line72 × 720.586M : 8.8(12.0)/3200L : 9.7(13.2)/3300Special swirl precombution chamberNatural aspiratedElectric motor (12V 1.3kW)Direct sea water coolingMechanical155 with Y-5M712.5×463×598 with Y-5M
SpecificationsModelNumber of cyl indersBore × strokeDisplacementRated output
Combution systemAspi rationStarting systemCooling systemMarine gearDry mass
Dimensions (L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
4JHYE4 in-l ine78 × 861.644M : 25.7(35)/3400L : 29.4 (38)/3600Di rect i njectionNatural aspi ratedElectric motor (12V 1.8kW)Heat exchangerHydaulic243 with YX-10916.3×545×659 with YX-10
2GMYM・L-rating 8.8~9.7kW (12.0~13.2mhp)MARINE
PROPULSIONDIESEL ENGINE
4JHYEM・L-rating 25.7~29.4kW (35~38mhp)MARINE
PROPULSIONDIESEL ENGINE
•Exhaust pipe •Kingston cock •Stop cable 3m •Battery switch•A-type instrument panel •Wiring harness 3m •LO evacuation pump
•Installation parts •Half coupling •Standard tools
Accessories
•Exhaust pipe •Remote control head •Remote control cable 4m•B-type instrument panel •Wiring harness 4m •Standard spare parts
•Standard tools •Installation parts •Battery switch •Kingston cock•LO evacuation pump •FO water separator •Bilge pump
Accessories
Dimensions Unit:mmDimensions Unit:mm
Rear view Right side view Rear view Right side view545
10145
407
119.
5 33.5
4.5
66.5
100
226
433
407.
5
659
278
45°
267140.6
103 450.7558832.25 28.855.25916.3
163
247Water outletφ25
Water inletφ26
329
100
61049
111
6
377
598
221
φ10
0
74
φ60
224
62
100 505
18127.5
695.58 9712.5
170210300454
230463
213 926.5532.5170
• Direct injection, heat exchanger cooling.• Natural aspirated 4- and 6-cylinder.• Durable hydraulic marine gear.
CD E
B
F
G
HI
A
300290280270260250240
80
60
40
20
0
1400 1600 1800 2000 2200 2400 2550 Sp
ecifi
c Fu
el C
onsu
mp
tion
: gr/
kW・h
r
Out
put
: kW
Speed of Crankshaft : rpm
6CHE3
Specific Fuel Consumption (Cubic Curve)
Output
(Cubic
Curve)
Output (Maximum)
60
50
40
30
20
10
0
320310300290280270260250
1400 1600 1800 2000 2200 2400 2550
Out
put
: kW
Sp
ecifi
c Fu
el C
onsu
mp
tion
: gr/
kW・h
r
Speed of Crankshaft : rpm
4CHE3
Output
(Cub
ic Cu
rve)
Specific Fuel Consumption (Cubic Curve)
Output (Maxi
mum)
•Breather hose with fittings •Drain separator •Evacuation hand pump •Fresh water sub-tank •Alternator 600W
•Instrument panel for wheel house (B/D-type) •Half coupling •Standard spare parts kit • Standard tool kit •Operation manual
[ 6 ] [ 7 ]
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated output
Combution systemAspirationStarting systemCooling systemMarine gearDry massDimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
4CHE34 in-line105 × 1254.330M : 57.4(78)/2550 L : 62.5(85)/2600 Direct injectionNatural aspiratedElectric starting motor (24V 4.0 kW)Heat exchangerHydraulic568 1183.5×688×1021with YX20
6CHE36 in-line
6.494M : 84.6(115)/2550 L : 95.6(130)/2600
700 1496.3×690×1018with YX30
Engine model : 4CHE3・6CHE3ModelTypeReduction ratio (Ahead) Direction of rotation (propeller shaft)
Dry weight kg
YX-20Hydraulic multi-disc clutch, wet type2.03Clockwise or counter-clockwise viewed from stem68
YX-30
70
2.55 2.96 3.48
A
1183.5
1496.3
Model
4CHE3×YX-20-1
6CHE3×YX-30-2
B
1021
1018
C
688
690
D
232
232.5
E
292
300
F
734
737
G
9
9
H
234
233
I
510
550
4CHE3/6CHE3M・L-rating 57.4~95.6kW (78~130mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
•Installation parts •Exhaust bellows •Exhaust silencer •Sea water filter•Kingston •Bilge pump •Battery switch
•Remote control head & cable•Pipes for exhaust , sea water, fuel oil
Accessories
Engine only / Front view
With gearbox / Rear view
Engine only / Left side view
With gearbox / Left side view
– Marine gear
233.5
139
912.5
64.5
18222018988
402277
NO.4 CYL CENTERNO.1 CYL CENTER
H
B
F
CE
G
I
D 1201.5
233277.5
88 284
691
189
903
NO.6 CYL CENTER
4CHE3 6CHE3
Specifications
Marine gear specifications
6CH-HTE3/DTE3/UTEM・L-rating 125~206kW (170~280mhp)MARINE
PROPULSIONDIESEL ENGINE
• Direct injection, heat exchanger cooling.• Turbocharger + intercooler.• Durable hydraulic marine gear.• 6CH-DTE3 and 6CH-UTE conform to IMO emissions regulations.
A
1575
1599.5
1599.5
1599.5
6CH-HTE3×YX-50S
6CH-HTE3×YX-71
6CH-DTE3×YX-71
6CH-UTE×YX-71
290280270260250240230
120
100
80
60
40
20
01400 1600 1800 2000 2200 2400 2550 S
pec
ific
Fuel
Con
sum
ptio
n : g
r/kW・h
r
Out
put
: kW
Speed of Crankshaft : rpm
6CH-HTE3
Specific Fuel Consumption (Cubic Curve)
Output
(Cub
ic Cu
rve)
Output
(Max
imum
)
260250240230220
170
150
100
50
01400 1600 1800 2000 2200 2400 2550 S
pec
ific
Fuel
Con
sum
ptio
n : g
r/kW・h
r
Out
put
: kW
Speed of Crankshaft : rpm
6CH-DTE3
Specific Fuel Consumption (Cubic Curve)
Output
(Cubic
Curve
)
Output
(Max
imum
)
260250240230220
200
150
100
50
01400 1600 1800 2000 2200 2400 2550 S
pec
ific
Fuel
Con
sum
ptio
n : g
r/kW・h
r
Out
put
: kW
Speed of Crankshaft : rpm
6CH-UTE
Specific Fuel Consumption (Cubic Curve)
Output
(Cubic
Curve
)
Outp
ut (M
axim
um)
[ 8 ] [ 9 ]
ModelNumber of cylindersBore × strokeDisplacementRated output
Combution systemAspirationStarting systemCooling systemMarine gearDry mass
Dimensions(L×W×H)
mm
lit.
kW(hp)/rpm
kg
mm
6CH-HTE36 in-line105 × 1256.494M : 125(170)/2550 L : 140(190)/2600 Direct injectionTurbocharger + intercoolerElectric starting motor (24V 4.0kW)Heat exchangerHydraulic795 1575×736×1096
6CH-UTE
M : 188(255)/2550 L : 206(280)/2600
940 1599.5×736×1111
6CH-DTE3
M : 154(210)/2550 L: 169(230)/2600
900 1599.5×736×1096
Engine model : 6CH-HTE3, 6CH-DTE3, 6CH-UTEModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YX-50S(or YX-71)Hydraulic multi-disc clutch, wet type2.07Clockwise or counter-clockwise viewed from stem117 (or 214)
YX-71
214
2.58 2.91 3.53
B
1096
1096
1096
1111
C
736
736
736
736
D
193
193
193
193
E
340
340
340
340
F
815
815
815
815
G
9
9
9
9
H
233
233
233
233
I
550
550
550
550
Dimensions Unit:mm
Performance curves
•Breather hose with fittings •Drain separator •Evacuation hand pump •Fresh water sub-tank •Alternator 600W
•Instrument panel for wheel house (D-type) •Half coupling •Standard spare parts kit •Standard tool kit •Operation manual•Exhaust bellows
•Installation parts •Exhaust silencer •Sea water filter •Kingston •Bilge pump •Battery switch
•Remote control head & cable•Pipes for exhaust , sea water, fuel oil
Accessories
C
D E
B
F
G
H
I
A
With gearbox / Front view With gearbox / Left side view
Engine only / Front view Engine only / Left side view
– Marine gear
9
1201.5736
193
233
550
340
815
6CH-
HTE3
: 10
966C
H-DT
E3 :
1096
6CH-
UT3
: 111
1
300
250
200
150
100
50
01400 1600 1800 2000 2200 2400 2600
240230220210
Speed of Crankshaft: rpm
Sp
eific
Fue
l Con
sum
ptio
n: g
/kW
.hr
Out
put
: kW
Output
Specific Fuel Consumption (Cubic Curve)
Output
(Cub
ic Cu
rve)
[ 10 ] [ 11 ]
Specifications
Marine gear specifications
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler.• Durable hydraulic marine gear.• 4-valves per cylinder for higher combustion efficiency.• Conform to IMO emissions regulations.
ModelNumber of cylindersBore × strokeDisplacementRated output
Combution systemAspirationStarting systemCooling systemMarine gearDry mass
Dimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
6CX-GTYE6 in-line110 × 1657.413M : 265(360)/2600L : 294(400)/2700Direct injectionTurbocharger + intercoolerElectric starting motor (24V 4.0kW)Heat exchangerWithout marine gear1060 with YX-71-1 marine gear1586×897×964
Engine model : 6CX-GTYEModelTypeReduction ratio (Ahead) Direction of rotation (propeller shaft)
Dry weight kg
YX-71-1Hydraulic multi-disc clutch, wet type2.07Clockwise or counter-clockwise viewed from stem210
2.58 2.91
6CX-GTYEM・L-rating 265~294kW (360~400mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
•Breather hose with fittings •Exhaust flexible joint for T/C out •Drain separator•Evacuation hand pump •Fresh water sub tank
•A lternator 980W •Instrument panel for wheel house (D-type) •Half coupling •Daily maintenance tool kit •Operation manual •Standard spare parts
•Installation parts •Flex ible mounting •Exhaust silencer •Sea water filter•Kingston •Bilge pump •Battery switch •Remote control head & cable
•Wiring harness •Pipes for exhaust , sea water, fuel oil
Accessories
6CX-GTYE
Engine only / Right side view
With gearbox / Right side view
Engine only / Front view
With gearbox / Rear view
– Marine gear
372
308203
21
38.5
15861026398 162
179
79(9)
141141
250
100
180245
764
)(R
IMOV
ING
PIST
ONM
INIM
UM H
EIGH
T FO
R
357
93
420.6538
897
377.4
165
(25)
543
359
910
0
281
75 75
550
964
583
381
372
20338.5
14961026308 162
Speed of Crankshaft : rpm
Output: kW
Fuel
Con
sum
ptio
n:
L/h
Fuel
Con
sum
ptio
n: g
r/kW・
hr
Out
put
: kW
Torq
ue: N・
m
•Breather hose with fittings •Exhaust flexible joint (T/C out)•Evacuation hand pump •Fresh water sub-tank
•Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Installation parts •FPTO V-pulley •Exhaust silencer •Exhaust flexible joint for piping •Sea water filter •Kingston •Bilge pump •Duplex FO filter •Drain separator
•2 pole wiring •A lternator 980W •Remote control head & cable •2 station instrument panel (C-type) •Stop solenoid •Wiring harness •Pipes for exhaust , sea water, fuel oil
Accessories
Fuel consumption comparison Fuel consumption
Output
Torque
1584.5 B
AD
FE
CI II
I II
6HA2M-HTE H-rating 204kW (278mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
[ 12 ] [ 13 ]
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler models.• Available either with marine gear or without marine gear.• Conform to IMO emissions regulations. • Type approved by BV, GL, RINA .
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry mass (without marine gear)
Dimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
6HA2M-HTE6 in-line130 × 16513.140H : 204(278)/1880 Direct injectionTurbocharger + intercoolerElectric starting motor (24V 6.0kW)Heat exchanger13401584.5×1016×1260
Engine model : 6HA2M-HTEModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YX-120Hydraulic multi-disc clutch2.03Clockwise or counterclockwise310
2.57 3.04 3 .55
YX-120L
4.00
385
4.59
A
2004.5
2038.5
Model
6HA2M-HTE×YX-120
6HA2M-HTE×YX-120L
B
420
454
C
1272
1384
D
1016
1016
E
499
499
F
517
517
Engine only / Front view
With YX120L gearbox / Front view
Engine only / Right side view
With YX120L gearbox / Left side view
– Marine gear
1016499
330171.
5
771
1260
386
874
517
159.
5
836
CRAN
K CE
NTE
R
130
FOR
REM
OVIN
G PI
STON
1991087
271
295
1584.5276.5 438870
CYL.
No.1
CYL.
No.6
Propeller power curve
Propeller power curve
Max. output
Max. output
600
0 50 100 150 200 250
800 1000 1200 1400 1600 1800 20000
500
1000
1500
0
0
20
40
60
50
100
150
200
250
50
100
150
200
250
300
200
210
220
230
240
01000800 1200 1400
Speed of Crankshaft: rpm
Sp
ecifi
c Fu
el C
onsu
mp
tion:
g
r/kW・h
rO
utp
ut: k
W
1600 1800 2000 2200
Output
(Cubic
curve
)Output(M
ax. cu
rve)
6HA2M-HTEM-rating 257kW (350mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
•Breather hose with fittings •Exhaust flexible joint (T/C out)•Evacuation hand pump •Fresh water sub-tank
•Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Installation parts •FPTO V-pulley •Exhaust silencer •Exhaust flexible joint for piping •Sea water filter •Kingston •Bilge pump •Duplex FO filter •Drain separator
•2 pole wiring •Alternator 980W •Remote control head & cable •2 station instrument panel (C-type) •Stop solenoid •Wiring harness •Pipes for exhaust , sea water, fuel oil
Accessories
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler models.• Available either with marine gear or without marine gear.• Conform to IMO emissions regulations.• Type approved by BV, GL, RINA.
[ 14 ] [ 15 ]
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry mass (without marine gear)
Dimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
6HA2M-HTE6 in-line130 × 16513 .140M : 257(350)/1950 Direct injectionTurbocharger + intercoolerElectric starting motor (24V 6.0kW)Heat exchanger13401584.5×1016×1260
Engine model : 6HA2M-HTEModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YX-120Hydraulic multi-disc clutch2.03Clockwise or counterclockwise310
2.57 3 .04 3 .55
YX-120L
4.00
385
4.59
A
2004.5
2038.5
6HA2M-HTE×YX-120
6HA2M-HTE×YX-120L
B
420
454
C
1272
1384
D
1016
1016
E
499
499
F
517
517
Engine only / Front view
With YX120 gearbox / Front view
Engine only / Right side view
With YX120 gearbox / Left side view
– Marine gear
1584.5 B
AD
FE
CI II
I II
1016
49933017
1.5
771
1260
386
874
517
159.
5
836
CRAN
K CE
NTE
R
130
1991087
271
295
1584.5
276.5 438870
CYL.
No.1
CYL.
No.6
Specific fuel consumption(at cubic curve)
•Breather hose with fittings •Exhaust flexible joint (T/C out)•Evacuation hand pump •Fresh water sub-tank
•Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Installation parts •FPTO V-pulley •Exhaust silencer •Exhaust flexible joint for piping •Sea water filter •Kingston •Bilge pump •Duplex FO filter •Drain separator
•2 pole wiring •Alternator 980W •Remote control head & cable •2 station instrument panel (C-type) •Stop solenoid •Wiring harness •Pipes for exhaust , sea water, fuel oil
Accessories
50
100
150
200
250
300
190
200
210
220
230
01000800 1200 1400
Speed of Crankshaft: rpm
Sp
ecifi
c Fu
el C
onsu
mp
tion:
gr/
kW・
hrO
utp
ut: k
W
1600 1800 2000 2200
Outp
ut(M
ax. c
urve
)Outp
ut(C
ubic
curve
)
Specific fuel consumption(at cubic curve)
1584.5 B
AD
FE
C
I II
I II
6HA2M-DTEM-rating 298kW (405mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler models.• Available either with marine gear or without marine gear.• Conform to IMO emissions regulations.• Type approved by BV, GL, RINA.
[ 16 ] [ 17 ]
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry mass (without marine gear)
Dimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
6HA2M-DTE6 in-line130 × 16513.140M : 298(405)/1950Direct injectionTurbocharger + intercoolerElectric starting motor (24V 6.0kW)Heat exchanger13501586×1036.5×1260
2.57 3.04
YX-120L
3.46
385
4.00 4.59
Engine model : 6HA2M-DTEModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YX-120Hydraulic multi-disc clutch2.03Clockwise or counterclockwise310
A
2004.5
2038.5
6HA2M-DTE×YX-120
6HA2M-DTE×YX-120L
B
420
454
C
1272
1384
D
1036
1036
E
519
519
F
517
517
Engine only / Front view
With YX120 gearbox / Front view
Engine only / Left side view
With YX120 gearbox / Left side view
– Marine gear
171.
5
1036
519
771
1260
386
874
517362
159.
5836
130
CRAN
K CE
NTE
R
1584.5
276.5 438870290
271
CYL.
No.1
CYL.
No.6
400
300
200
100
0
kW
2500
2000
1500
1000
500
0
N·m
14001000 1200 1600 1800 2000Speed of Crankshaft: rpm
Output
Torque150
100
50
0
Fuel ConsumptionL/h
6HYM-ETEH-rating 368kW (500mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
•Breather hose with fittings •Fresh water sub-tank •A lternator 980W •2 pole wiring•Instrument panel for wheel house (D-type) •Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Remote control head & cable •Wiring harness •2 station instrument panel (C-type) •Installation parts •FPTO V-pulley •Double walled FO pipes •Duplex FO filter
•Intake air heater •Horizontal exhaust outlet•Mixing elbow •Flex ible mounts •Sea water filter •Kingston •Bilge pump •LO priming pump •LO evacuation pump •Drain separator •Exhaust thermometer
•Flex ible joint at T/C outlet •Flex ible joint for piping •Exhaust silencer •Battery switch •Pipes for sea water, fuel oil
Accessories
• 6-cylinder, direct injection, heat exchanger cooling.• Twin-turbocharger + intercooler.• Available either with marine gear or without marine gear.• 4-valves per cylinder for higher combustion efficiency.• Conform to IMO emissions regulations.• Type approved by NK, ABS, BV, RINA .
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry massDimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
6HYM-ETE6 in-line132.9 × 16513.733368(500)/1950Direct injectionTurbocharger + intercoolerElectric starting motor (24V 6.0kW)Heat exchanger1385(without marine gear)1556×1014×1133
Engine model : 6HYM-ETEModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YXH-160Hydraulic multi-disc clutch1.97Clockwise or counterclockwise390
2.46 3 .05
YX-161L
3 .65
620
4.08 4.55
Performance curves
[ 18 ] [ 19 ]
No.6
No.1
277446
870 352 39
265
18
1556
401
866
119
678
200 63
0
319
311
277 446
870 352 39
265
535
319
812
1947
356
762149
Engine only / Front view
With YX161L gearbox / Rear view
Engine only / Right side view
With YX161L gearbox / Right side view
– Marine gear
Propeller power curveMax.
output
Propeller power curve
Max. ou
tput
119
267
86674
7
790
490524
1014
1133
600
500
400
300
200
100
0
kW
3000
2500
2000
1500
1000
500
0
N·m
14001000 1200 1600 1800 2000 2200 2400
Output
Torque
150
100
50
0
Fuel ConsumptionL/h
600
500
400
300
200
100
0
kW
3000
2500
2000
1500
1000
500
0
N·m
14001000 1200 1600 1800 2000 2200 2400Speed of Crankshaft: rpm
Output
Torque
150
100
50
0
Fuel ConsumptionL/h
6HYM-ETE M-rating 441kW (600mhp) L-rating 478kW (650mhp)
MARINE PROPULSION
DIESEL ENGINE Dimensions Unit:mm
•Breather hose with fittings •Fresh water sub-tank •A lternator 980W •2 pole wiring •Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Remote control head & cable •Wiring harness •2 station instrument panel (C-type) •Installation parts •FPTO V-pulley •Double walled FO pipes •Duplex FO filter
•Intake air heater •Horizontal exhaust outlet•Mixing elbow •Flex ible mounts •Sea water filter •Kingston •Bilge pump •LO priming pump •LO evacuation pump •Drain separator •Exhaust thermometer
•Flex ible joint at T/C outlet •Flex ible joint for piping •Exhaust silencer •Battery switch •Pipes for sea water, fuel oil
Accessories
Performance curves
• 6-cylinder, direct injection, heat exchanger cooling.• Twin-turbocharger + intercooler.• Available either with marine gear or without marine gear.• 4-valves per cylinder for higher combustion efficiency.• Conform to IMO emissions regulations.• Type approved by NK, ABS, BV, RINA .
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated output
Combution systemAspirationStarting systemCooling systemDry massDimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
6HYM-ETE L-rating / M-rating6 in-line132.9 × 16513.733M : 441(600)/2100L : 478(650)/2150Direct injectionTurbocharger + intercoolerElectric starting motor (24V 6.0kW)Heat exchanger1385(without marine gear)1556×1014×1133
Engine model : 6HYM-ETE L-rating / M-ratingModelTypeReduction ratio (Ahead) Direction of rotation (propeller shaft)
Dry weight kg
YXH-160Hydraulic multi-disc clutch1.97Clockwise or counterclockwise390
2.46 3 .05
YX-161L
3 .65
620
4.08 4.55
[ 20 ] [ 21 ]
L-rating M-rating
No.6
No.1
277446
870 352 39
265
18
1556
277 446
870 352 39
265524
233
617
2155
894
1936
401
678
457
119
114
760
233
224
866
Engine only / Front view
With YXH160 gearbox / Rear view
Engine only / Right side view
With YXH160 gearbox / Right side view
– Marine gear
Max. output
Marine cubic curve
Max. output
Marine cubic curve
Max. output
Marine cubic curve
Max. output
Marine cubic curve
119
267
86674
7
790
490524
1014
1133
600
500
400
300
200
100
0
kW
3000
2500
2000
1500
1000
500
0
N·m
14001000 1200 1600 1800 2000 2200 2400Speed of Crankshaft: rpm
Output
Torque150
100
50
0
Fuel ConsumptionL/h
6HYM-ETES-rating 515kW (700mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
•Breather hose with fittings •Fresh water sub-tank •A lternator 980W•Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Remote control head & cable •Wiring harness •2 station instrument panel (C-type) •Installation parts •FPTO V-pulley •Double walled FO pipes •Duplex FO filter
•Intake air heater •Horizontal exhaust outlet•Mixing elbow •Flexible mounts •Sea water filter •Kingston •Bilge pump •LO priming pump •LO evacuation pump •Drain separator •Exhaust thermometer
•Flexible joint at T/C outlet •Flexible joint for piping •Exhaust silencer •Battery switch •Pipes for sea water, fuel oil
Accessories
• 6-cylinder, direct injection, heat exchanger cooling.• Twin-turbocharger + intercooler.• Available either with marine gear or without marine gear.• 4-valves per cylinder for higher combustion efficiency.• Conform to IMO emissions regulations.
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry massDimensions(L×W×H)
mm
lit .
kW(hp)/rpm
kg
mm
6HYM-ETE S-rating6 in-line132.9 × 16513.733515(700)/2200Direct injectionTurbocharger + intercoolerElectric starting motor (24V 6.0kW)Heat exchanger1385(without marine gear)1556×1014×1133
Engine model : 6HYM-ETE S-ratingModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YXH-130Hydraulic multi-disc clutch2.03Clockwise or counterclockwise280
2.57 3 .04
[ 22 ] [ 23 ]
No.6
No.1
277446
870 352 39
265
18
1556
401
119
678
403
89
866
208
195
760
277 446
870 352 39
265
413
690
1825
208
125.5
2076.5
Engine only / Front view
With YXH130 gearbox / Rear view
Engine only / Right side view
With YXH130 gearbox / Right side view
– Marine gear
Max. output
Marine cubic curve
Max. output
Marine cubic curve
119
267
86674
7
790
490524
1014
1133
150
100
50
0
Fuel ConsumptionL/h
6AYM-STEH-rating 485kW (659mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
•Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Remote control head & cable •2 station instrument panel (C-type)•Wiring harness •Air starting motor •Flex ible mounts (for engine) •FPTO V-pulley •Horizontal exhaust •Shallow sump
•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring•Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump
•Flex ible joint for exhaust piping •Exhaust silencer •Battery switch •A lternator 980W •Pipes for exhaust , sea water, fuel oil
Accessories
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler.• 4-valves per cylinder for higher combution efficiency.• Available either with marine gear or without marine gear.• Conform to IMO emissions regulations.• Type approved by NK, ABS, BV, RINA , CCS.
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry mass
mm
lit .
kW(hp)/rpm
kg
6AMY-STE6 in-line155 × 18020.379H : 485(659)/1900Direct injectionTurbocharger + intercoolerE lectric starting motor (24V 7.0kW) Heat exchanger2365
Engine model : 6AYM-STEModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YX-181Hydraulic multi-disc clutch2.08Clockwise or counterclockwise560
2.55 3.03
YX-180L
3.50
680
4.00 4.54
YXH-240L
4.89
1240
5.36 5.91 6.57 6.95
[ 24 ] [ 25 ]
No.1 CYL.
1000520 480
No.6 CYL.
343
2661609541
2364
194 .5
267
293 .5
370 370
195 195
167
100 52
2
75° 75°
With YX181 gearbox / Rear view
With YX180L gearbox / Rear view
With YX181 gearbox / Right side view
With YX180L gearbox / Right side view
– Marine gear
500
400
300
200
100
0
kW
Speed of Crankshaft: rpm
Output
Max
. out
put
Propell
er po
wer cu
rve
900 1100 1300 1500 1700 1900 2100
5000
4000
3000
2000
1000
0
N・m
Engine speed: rpm
Torque
800 1000 1200 1400 1600 1800 2000 2200
4801000343
2661343560
330
No.6 CYL.No.1 CYL.
194.5
5712394
293.5
2316
716
3
640
260260
70°
70°
393 393
200
150
100
500
Fuel ConsumptionL/h
6AYM-ETEH-rating 555kW (755mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
Performance curves
•Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Remote control head & cable •2 station instrument panel (C-type)•Wiring harness •Air starting motor •Flex ible mounts (for engine) •FPTO V-pulley •Horizontal exhaust •Shallow sump
•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring •Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump
•Flex ible joint for exhaust piping •Exhaust silencer •Battery switch •A lternator 980W •Pipes for exhaust , sea water, fuel oil
Accessories
[ 26 ] [ 27 ]
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler.• 4-valves per cylinder for higher combution efficiency.• Available either with marine gear or without marine gear.• Conform to IMO emissions regulations.• Type approved by NK, ABS, BV, RINA, CCS.
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry mass
mm
lit .
kW(hp)/rpm
kg
6AMY-ETE H6 in-line155 × 18020.379H : 555(755)/1840Direct injectionTurbocharger + intercoolerElectric starting motor (24V 7.0kW)Heat exchanger2365
Engine model : 6AYM-ETE HModelTypeReduction ratio (Ahead) Direction of rotation (propeller shaft)
Dry weight kg
YXH-240Hydraulic multi-disc clutch1.95Clockwise or counterclockwise645
2.27 2.56 3.03 3.48
YXH-240L
4.89
1240
5.36 5.91 6.57 6.95
Engine only / Front view
With YXH240L gearbox / Rear view
Engine only / Right side view
With YXH240L gearbox / Right side view
– Marine gear
No.1 CYL .
1000 480
No.6 CYL.
194 .5266
194
279.5343747
414
2570
1609795
834
2130
0
810
302 302
60° 60°
No.1 CYL .
1000 480
No.6 CYL.
194 .5266
194
279.5343
1823
1609
481641 664
1305
171.
581
7
175177962
2238
4.5
167
551.
587
914
30.5
946
CRAN
K CE
NTER
700
600
500
400
300
200
100
0
kW
Speed of Crankshaft: rpm
Output
Max
. out
put
Propell
er po
wer cu
rve
900 1100 1300 1500 1700 1900 2100
5000
4000
3000
2000
1000
0
N・m
Engine speed: rpm
Torque
800 1000 1200 1400 1600 1800 2000 2200
200
150
100
500
Fuel ConsumptionL/h
6AYM-ETEM-rating 610kW (829mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
•Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Remote control head & cable •2 station instrument panel (C-type)•Wiring harness •Air starting motor •Flex ible mounts (for engine) •FPTO V-pulley •Horizontal exhaust •Shallow sump
•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring•Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump
•Flex ible joint for exhaust piping •Exhaust silencer •Battery switch •A lternator 980W •Pipes for exhaust , sea water, fuel oil
Accessories
[ 28 ] [ 29 ]
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler.• 4-valves per cylinder for higher combution efficiency.• Available either with marine gear or without marine gear.• Conform to IMO emissions regulations.• Type approved by NK, ABS, BV, RINA , CCS.
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry mass
mm
lit .
kW(hp)/rpm
kg
6AMY-ETE M6 in-line155 × 18020.379M : 610(829)/1900Direct injectionTurbocharger + intercoolerElectric starting motor (24V 7.0kW)Heat exchanger2365
Engine model : 6AYM-ETE MModelTypeReduction ratio (Ahead) Direction of rotation (propeller shaft)
Dry weight kg
YXH-240Hydraulic multi-disc clutch1.95Clockwise or counterclockwise645
2.27 2.56 3.03 3.48
YXH-240L
4.89
1240
5.36 5.91 6.57 6.95
Performance curves
1305
1430
.587
9
2000
1000 480
194 .5 266
194
313
535 .5 1609
279 .5343651
2474
60819
167
195 195586
65° 65°
Engine only / Front view
With YXH240 gearbox / Rear view
Engine only / Right side view
With YXH240 gearbox / Right side view
– Marine gear
700
600
500
400
300
200
100
0
kW
Speed of Crankshaft: rpm
Output
Max
. out
put
Propell
er po
wer cu
rve
900 1100 1300 1500 1700 1900 2100
5000
4000
3000
2000
1000
0
N・m
Engine speed: rpm
Torque
800 1000 1200 1400 1600 1800 2000 2200
6AYM-GTEL-rating 670kW (911mhp)MARINE
PROPULSIONDIESEL ENGINE Dimensions Unit:mm
•Breather hose with fittings •Exhaust flexible joint (T/C out) •Fresh water sub-tank •Instrument panel for wheel house (D-type)•Standard spare parts •Standard tool kit •Operation manual
•YX gearbox •Remote control head & cable •2 station instrument panel (C-type)•Wiring harness •Air starting motor •Flex ible mounts (for engine) •FPTO V-pulley •Horizontal exhaust •Shallow sump
•Duplex LO filter •Duplex FO filter •Double walled FO pipes •2 pole wiring •Engine-mounted instrument panel •Intake air heater •Exhaust thermometer •Installation parts •Sea water filter •Kingston •Bilge pump
•Flex ible joint for exhaust piping •Exhaust silencer •Battery switch •A lternator 980W •Pipes for exhaust , sea water, fuel oil
Accessories
[ 30 ] [ 31 ]
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputCombution systemAspirationStarting systemCooling systemDry mass
mm
lit .
kW(hp)/rpm
kg
6AMY-GTE6 in-line155 × 18020.379L : 670(911)/1938 Direct injectionTurbocharger + intercoolerElectric starting motor (24V 7.0kW)Heat exchanger2365(without marine gear)
Engine model : 6AYM-GTEModelTypeReduction ratio (Ahead)
Direction of rotation (propeller shaft)
Dry weight kg
YXH-240Hydraulic multi-disc clutch1.95Clockwise or counterclockwise645
2.27 2.56 3.03 3.48
Performance curves
Engine only / Front view
With YXH240 gearbox / Rear view
Engine only / Right side view [Shallow sump]
With YXH240 gearbox / Right side view
– Marine gear
1000 480
194 .5 266
194
313
1330
.587
9
535.5 1609
279 .5343651
2474
20001305
60819
167
195 195
58665° 65°
250200150100500
Fuel ConsumptionL/h
1000 1200 1400 1600 1800 2000
700
600
500
400
300
200
100
0
kW
Engine Speed: rpm
Output
Max
. out
put
Propell
er cu
rve
900 1100 1300 1500 1700 1900 2100
5000
4000
3000
2000
1000
0
N・m
Engine speed: rpm
Torque
800 1000 1200 1400 1600 1800 2000 2200
• 6-cylinder, direct injection, heat exchanger cooling.• Turbocharger + intercooler.• 4-valves per cylinder for higher combution efficiency.• Available either with marine gear or without marine gear.• Conform to IMO emissions regulations.• Type approved by NK, ABS, BV, RINA , CCS.
93 95480
33.5
31.5
6523
7.544
2.568
0
190.5265
4.5
278543
28.8701.3
309.1
180.6
730.1
183.8
JH series (Life Boat Engines)
18.4~24.3kW (25~33mhp)MARINE PROPULSION
DIESEL ENGINE
[ 32 ] [ 33 ]
• Comply with SOLAS'96.• Engine keeps on running after a 360 degree roll.• Engine can run at least five minutes in water up to centerline of crankshaft.• Engine is designed to withstand a free fall (fitted on a life boat).
Specifications
Marine gear specifications
ModelNumber of cylindersBore × strokeDisplacementRated outputMax. output Combution systemAspirationStarting systemCooling systemMarine gearDry weight
mm
lit.
kW(PS)/rpm
kW(PS)/rpm
kg
3JH25A382 × 861.36318.4(25)/320020.2(27.5)/3300Direct injectionNutural aspiratedElectric starting motor (12V 1.8kW)Heat exchanger / Keel coolingMechanical187
3JH30A
22.1(30)/290024.3(33)/3000
Engine model : JHModelTypeReduction ratio Direction of rotation (propeller shaft)
KM35P1Hydraulic multi-disc clutchAhead: 2.36Clockwise or counterclockwise
Astern: 3.16
Dimensions Unit:mm
•Breather hose with fittings •Evacuation hand pump •Charging alternator •Instrument panel for wheel house (B-type)
•Kingston cock •Wiring harness 4m •Half coupling (rough bore type) •Standard spare parts •Standard tool kit •Operation manual
Accessories
MARINE AUXILIARY
DIESEL ENGINE
Rear view Right side view
F G（fo
r Re
mov
ing
Pist
on）
B
E D
A
4CHL series38~62hp / 1500~1800rpm30~50kVA (24~40kW)
MARINE AUXILIARY
DIESEL ENGINE Dimensions Unit:mm
[ 34 ] [ 35 ]
SpecificationsModelNumber of cylindersBore × strokeDisplacementContinuous rated engine speed
Continuous rated outputApplicable generator capacity
FrequencyCombution systemAspirationDry weight (Engine only)Dry weight (Gen. set)
mm
lit.
rpm
hp
kVA(kW)
Hz
kg
kg
4CHL-NIn-line 4105 × 1254.331500
3830(24)
50Direct injectionNutural aspiration500960
4CHL-TN
1500
5040(32)
50
Exhauust Turbocharger5201010
1800
5040(32)
60
1800
6250(40)
60
Model4CHL-N4CHL-TN
A15551567
B922922
D13501350
E522522
F473473
G11641164
Generator set dimensions for your reference Unit:mm
Generator set dimensions shown below depend on generator model
•Instrumental panel (attached to engine) •Cool ing system : Rubber impeller type sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat for fresh water / Emergency use sea water inlet•Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Single type)•Fuel system : Paper filter type fuel strainer / Drain separator to be mounted on vessel•Turbocharging system : Exhaust gas outlet expansion joint from engine (TN)•Electrical equipment : Starter motor (DC24V) 4.0kW / Battery switch / 2 pole wiring•Thermometer : Exhaust gas at outlet of each cylinder (N) / Exhaust gas at inlet of turbocharger (TN) / Cooling water outlet / Lubrication oil at cooler inlet
Accessories
•Cool ing system : Kingston cock•Lubrication system : Manual priming pump / Inlet and outlet joint for semi dry sump•Fuel system : Primary fuel strainer to be mounted on vessel•Electrical equipment : Alternator (DC24V600W) •Generator (and common bed) : Taiyo or Stamford•Thermometer : Lubrication oil at cooler outlet•Electrical governor for parallel operation•Exhaust piping : Expansion joint for piping / Silencer•Compressed air starting device•Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring
• 4-cylinder, direct injection.• Natural aspi rated or turbocharged.• Type approved by BV.
300 4021089
387
φ35
2.425
+0.
08+
0.02
φ39
2
φ40
9.575
+0.
127
0
287
約29
032
553
6
21514064.5
21
192
12575
137.5
11
94
400 400800
287 38
1
691
232295
182
196
700
110
810
1191
172 254
Front view
Engine only (4CHL-TN)
Front view
Left side view
Left side view
– Generator
F G（fo
r Re
mov
ing
Pist
on）
B
E D
A
6CHL series62~120hp / 1500~1800rpm50~100kVA (40~80kW)
MARINE AUXILIARY
DIESEL ENGINE Dimensions Unit:mm
Model6CHL-N6CHL-TN6CHL-HTN
A1885.51945.51965.5
B942942942
D165017001700
E522522522
F474474474
G116511651165
[ 36 ] [ 37 ]
SpecificationsModelNumber of cylindersBore × strokeDisplacementContinuous rated engine speed
Continuous rated outputApplicable generator capacity
FrequencyCombution systemAspiration
Dry weight (Engine only)Dry weight (Gen. set)
mm
lit.
rpm
hp
kVA(kW)
Hz
kg
kg
6CHL-NIn-line 6105 × 1256.4941500
6250(40)
50Direct injectionNutural aspiration
6251170
6CHL-TN
1500
7460(48)
50
Exhauust Turbocharger
6451310
1800
7460(48)
60
1800
10080(64)
60
6CHL-HTN
1500
10080(64)
50
Exhauust Turbocharger with intercooler
6751340
1800
120100(80)
60
• 6-cylinder, direct injection .• Natural aspirated or turbocharged.• Type approved by BV.
189
233
25
1378300
111691 387
214.5
33 884.573
21
28819
2
287
536
325
381
100
281
691
(for
Rem
ovin
g Pi
ston
)
36
295
230
750
461
404942
522 420
110
860
1241
– Generator
Front view Left side view
Left side view
Generator set dimensions for your reference Unit:mm
Generator set dimensions shown below depend on generator model
Front view
Engine only (6CHL-HTN)
•Instrumental panel (attached to engine) •Cooling system : Rubber impeller type sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat for fresh water / Emergency use sea water inlet•Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Single type)•Fuel system : Paper filter type fuel strainer / Drain separator to be mounted on vessel•Turbocharging system : Exhaust gas outlet expansion joint from engine (TN, HTN)•Electrical equipment : Starter motor (DC24V) 4.0kW / Battery switch / 2 pole wiring•Thermometer : Exhaust gas at outlet of each cylinder (N) / Exhaust gas at inlet of turbocharger (TN, HTN) / Cooling water outlet / Lubrication oil at cooler inlet
Accessories
•Cooling system : Kingston cock•Lubrication system : Manual priming pump / Inlet and outlet joint for semi dry sump•Fuel system : Primary fuel strainer to be mounted on vessel•Electrical equipment : Alternator (DC24V600W) •Generator (and common bed) : Taiyo or Stamford•Thermometer : Lubrication oil at cooler outlet•Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer•Compressed starting device•Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring
HTN is not Type approved.
F
D
C
G（fo
r Re
mov
ing
Pist
on）
E
AB
4HAL2 series98~183hp / 1200~1800rpm80~150kVA (64~120kW)
MARINE AUXILIARY
DIESEL ENGINE Dimensions Unit:mm
Generator set dimensions for your reference Unit:mm
Generator set dimensions shown below depend on generator model
[ 38 ] [ 39 ]
• 4-cylinder, direct injection .• Type approved by BV, GL .
SpecificationsModelNumber of cylindersBore × strokeDisplacementContinuous rated engine speed
Continuous rated outputApplicable generator capacity
FrequencyCombution systemAspirationDry weight (Engine only)Dry weight (Gne. set)
mm
lit.
rpm
hp
kVA(kW)
Hz
kg
kg
4HAL2-TN1In-line 4130 × 1658.761200
9880(64)
50Direct injectionExhaust Turbocharger 10301785
1500
121100(80)
60
1855
1800
157130(104)
50
1855
4HAL2-TN
1200
122100(80)
60
1845
1500
156125(100)
50
1855
1800
183150(120)
60
1855Model4HAL2-TN14HAL2-TN
A2070.52070.5
B1116.51116.5
C12641264
D16001600
E559559
F529529
G13121312
No.4 CYL.No.1 CYL.
232
756
111.
5
526.5
1061.5
735
313
229 46
1
1196
535 485.5434
276.5
510
110
1429.5
R294
121
1244
– Generator
Front view
Engine only
Front view
Left side view
Left side view
•Instrumental panel (attached to engine) •Cool ing system : Sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat for fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Single type) / Manual priming pump•Fuel system : Paper filter type fuel strainer / Drain separator to be mounted on vessel•Turbocharging system : Exhaust gas outlet expansion joint from engine•Electrical equipment : Starter motor (DC24V) 5.5kW / Alternator (DC24V600W) / Battery switch / 2 pole wiring•Thermometer : Exhaust gas at outlet of each cylinder / Cooling water outlet / Lubrication oil at cooler inlet
Accessories
•Cool ing system : Kingston cock•Lubrication system : Inlet and outlet joint for semi dry sump•Fuel system : Primary fuel strainer to be mounted on vessel•Generator (and common bed) : Taiyo or Stamford•Thermometer : Exhaust gas at inlet of turbocharger / Lubrication oil at cooler outlet•Electrical governor for parallel operation•Exhaust piping : Expansion joint for piping / Silencer•Compressed air starting device•Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring
J.BOX
C
F G（fo
r Re
mov
ing
Pist
on）
BA
DE
6HAL2 series122~414hp / 1200~1800rpm100~350kVA (80~280kW)
MARINE AUXILIARY
DIESEL ENGINE Dimensions Unit:mm
Generator set dimensions for your reference Unit:mm
Generator set dimensions shown below depend on generator model
[ 40 ] [ 41 ]
• 6-cylinder, direct injection .• Natural aspirated or turbocharged. (with intercooler)• Type approved by NK, BV, GL .
SpecificationsModelNumber of cylindersBore × strokeDisplacementContinuous rated engine speed
Continuous rated outputApplicable generator capacity
FrequencyCombution systemAspiration
Dry weight (Engine only)
Dry weight (Gen. set)
mm
lit.
rpm
hp
kVA(kW)
Hz
kg
kg
6HAL2-NIn-line 6130×16513.141200
122100(80)
60Direct injectionNutural aspiration
13802220
1500
156125(100)
50
6HAL2-TN
1200
163130(104)
60
Exhaust Turbocharger
13952330
1500
204170(136)
50
2380
1800
244200(160)
60
2380
6HAL2-HTN
1200
217180(144)
60
Exhaust Turbocharger with intercooler
14102670
1500
299250(200)
50
2720
1800
360300(240)
60
2720
6HAL2-DTN
1200
271225(180)
60
14202790
1500
346290(232)
50
2820
1800
414350(280)
60
2820
Model6HAL2-N6HAL2-TN6HAL2-HTN6HAL2-DTN
A2388.52498.52573.52683.5
B1163.51163.51163.51163.5
C1344141014101410
D2100210022002200
E495527527527
F544544544544
G1327132713271327
No.1 CYL. No.6 CYL.
292
1331
783
1795
483
866
108
870
276.5
442
330
171.
5
515.5 599.5
1115
465
R370
– Generator
Front view
Engine only (6HAL2-TN, -HTN, -DTN)
Front view
Left side view
Left side view
•Instrumental panel (attached to engine) •Cooling system : Sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat for fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Tandem switch type) / Manual priming pump •Fuel system : Paper filter type fuel strainer / Drain separator to be mounted on vessel•Turbocharging system : Exhaust gas outlet expansion joint from engine•Electrical equipment : Starter motor (DC24V) 6.0kW / Alternator (DC24V600W) / Battery switch / 2 pole wiring •Thermometer : Exhaust gas at outlet of each cylinder / Cooling water outlet / Lubrication oil at cooler inlet
Accessories
•Cooling system : Kingston cock•Lubrication system : Inlet and outlet joint for semi dry sump•Fuel system : Primary fuel strainer to be mounted on vessel•Generator (and common bed) : Taiyo or Stamford•Thermometer : Exhaust gas at inlet of turbocharger (TN, HTN, DTN) / Lubrication oil at cooler outlet•Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer•Compressed air starting device•Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring
G（fo
r Re
mov
ing
Pist
on）
CF
B
D
A
E
6AYL series480~668hp / 1500~1800rpm400~562.5kVA (320~450kW)
MARINE AUXILIARY
DIESEL ENGINE Dimensions Unit:mm
Generator set dimensions for your reference Unit:mm
Generator set dimensions shown below depend on generator model
Engine only
• 6-cylinder, direct injection .• Turbocharged with intercooler.• Type approved by NK, ABS, BV, RINA, CCS.
[ 42 ] [ 43 ]
SpecificationsModelNumber of cylindersBore × strokeDisplacementContinuous rated engine speed
Continuous rated outputApplicable generator capacity
FrequencyCombution systemAspirationDry weight (Engine only)
Dry weight (Gen. set)
mm
lit.
rpm
hp
kVA(kW)
Hz
kg
kg
6AYL-STIn-line 6155 × 18020.3791800
480400(320)
60Direct injectionExhaust Turbocharger with intercooler24354120
6AYL-ET
1500
596500(400)
50
4780
1800
668562.5(450)
60
4300 5300Model6AYL-ST6AYL-ET
A3042.53389.5
B13461346
C15081508
D23802930
E738738
F619619
G15651565
NO.6CYL.
731
400
817
518.
5
177 175
2238
4.5
167
551.
587
9
946
279.5 343513.51000516.5
2030
93.5 214
481701641
1342
1430
.5
– Generator
Front view
Front view
Left side view
Left side view
•Instrumental panel (attached to engine)•Cool ing system : Sea water pump / Centrifugal type fresh water pump / Heat exchanger / Fresh water reservoir / Thermostat for fresh water / Emergency use sea water inlet •Lubrication system : Lubrication oil pump / Lubrication oil cooler / Lubrication oil filter (Tandem switch type) / Manual priming pump •Fuel system : Paper filter type fuel strainer / Drain separator to be mounted on vessel•Turbocharging system : Exhaust gas outlet expansion joint from engine•Electrical equipment : Starter motor (DC24V) 7.0kW / Alternator (DC24V600W) / Battery switch / 2 pole wiring •Thermometer : Exhaust gas at outlet of each cylinder / Cooling water outlet / Lubrication oil at cooler inlet
Accessories
•Cool ing system : Kingston cock•Lubrication system : Inlet and outlet joint for semi dry sump / Large wet sump•Fuel system : Primary fuel strainer to be mounted on vessel•Generator (and common bed) : Taiyo or Stamford•Thermometer : Exhaust gas at inlet of turbocharger / Lubrication oil at cooler outlet•Electrical governor for parallel operation •Exhaust piping : Expansion joint for piping / Silencer•Compressed starting device•Remote control device : Trip panel / Stop solenoid / LO pressure switch / FW temperature switch / Speed relay / Junction box & wiring
