Technical documents

/DES

IGN

ELEGANTO SPA

General dataOrder. Nr. R2012

Short descriptionHeterogeneous, rigid Design-Vinyl laying elements with an ISO10582-compliant connection profile free from adhesive on allsides

Type of installation Floating installation Full spread gluing

Area of application

Suitable for living spaces with an average indoor climate with40 to 60 % relative humidity and between 16 and 24° C, anddamp locations with temporary damp conditions up to 80 %relative humidity and occasional water splashes. Not suitablefor wet locations, such as shower rooms or similar(permanently damp, permanently wet, standing wetness). It isparticularly important to take into consideration the suitabilityof the subsurface for damp locations. Anhydrite is conditionallysuitable, wood materials are unsuitable.

Marble Macarena

/DES

IGN

Area of applicationsubsurface

Conforming to standards, ready for installation, dry, load-bearing subsurface with a flatness tolerance in conformity withDIN 18202 ÖNORM Table 3 Row 4 is required (for furtherInformation, see "TI_110 Information_Pruefpflichten_en.pdf") The material and work site must be sufficiently acclimatised,the inspection obligations as per DIN 18365 or thecorresponding standards and requirements of the respectivecountry must be met; readiness for installation must beestablished; it is particularly important to take intoconsideration the suitability of the subsurface for damplocations (anhydrite is suitable in certain circumstances, woodmaterials are unsuitable). On-site expansion joints must beused; an edge distance of approx. 5 mm is recommendedduring the installation; the rules of the trade and theinstallation guidelines included with the product must beadhered to.

Care instructions

Only factory-recommended care and cleansing agents shouldbe used; routine cleaning depends on the level of use and dirt,clean while damp and care in accordance with the careinstructions enclosed with the product

Dimensions ISO 24342 610,00 x 305,00

Commercial thickness ISO 24346 5,50

Top layer Vinyl suitable for use in damp locations

Grading/décor stone design

Wear layer 0,55 mm

Bevelled edge bevelled (4V)

Surface wave

construction 5-layer

Finish Twist PLUS varnished

Connection simpleFIX

Edge profiling Length profiling tiloFIX Angle System, cross profiling tilosimpleFix fold down

Technical dataWear group classification NKL 33 ISO 10582

Suitablity for castor wheels

Suitable with W typecastors - no debonding,minor changes to thesurface possible

EN 425

Flame class Bfl-s1 EN-ISO 9239-1

Formaldehyde E1 EN ISO 717-1

/DES

IGN

PCP free CEN/TR 14823

Impactsound reduction 17 dB EN ISO 717-2

Thermal resistance 0,020 m²K/W EN 12664

Slip resistance DS EN 13893

Dimensional stability ≤ 0,15 % ISO 23999

Resistance to chemicals 0 = very good ISO 26987

Light fastness >6 ISO 105-B02

Slip resistance R9 DIN 51130

Window areas

Please note that in rooms with large windows in particular,changes in colour caused by UV light cannot be ruled outcompletely and are therefore product-specific. Shading maybe necessary.

Delivery contentBoards per package 8,00 st

Packages per pallet 78 packages

Area per package 1,4880 m2

Area per pallet 116,06 m²

Weight per package 16,080 kg

Weight per pallet 1254,24 kg

Further informationEnvironmental sustainability

CE Declaration of Performance; REACH Declaration;Declaration of No-Objection

Underfloor heating When the heating is on, gaps may appear due to the dryambient air.

Floating installation in damplocations

When using this product, we recommend installingappropriate impact sound insulation. We recommend tiloNeutra underlay mat. Underlay that is too soft or that is notsuitable for damp/wet locations must not be used. Pleaseobserve the mat installation guidelines.

/DES

IGN

Full spread gluing

In order to smooth out any unevenness and maintain an evenlyabsorbent subsurface, smooth out pronounced roughness orremove sinter layers or sandy layers, the subsurface should besanded and vacuumed or, if necessary, built up to a suitablethickness with the appropriate precoats and fillers. Pleaseobserve the instructions of the products required and of therelevant building material suppliers.

Adhesive recommendation Apply tilo "EC1 PLUS adhesive for vinyl floors" using thenotched trowel recommended in the application instructions.

Tools requiredInstallation wedges, tapping block, pull bar (we recommendthe tilo installation set, order number Z1043), hammer,bracket, hand or electric saw (jigsaw, circular saw or chop saw).

Warning notice Store in a place that is protected from moisture, heat anddirect sunlight

This information is provided with the intention of offering you advice based on the best of our knowledge, on the basis of ourtrials, experiences, tests carried out, applicable standards and the rules of the trade. Should you require any additionalinformation, our technical and commercial advisors will be happy to assist you. Always consult our advisors for advice beforestarting any large-scale projects. We assume no liability for any errors and reserve the right to carry out technical modifications.

Please visit www.tilo.com for further information and updates.

Version : 1.00.052020

tilo GmbH | Magetsham 19 | A-4923 Lohnsburg+43 7754 400-0 | office@tilo.com | www.tilo.com