GROUP TAB LOCATORIntroduction

0 2 3 5 7 8A 8B 8E 8F 8G 8H 8I 8J 8L 8N 8O 8P 8Q 8R 8W 9 11 13 14 19 21 22 23 24 25

Lubrication & Maintenance Suspension Differential & Driveline Brakes Cooling Audio/Video Chime/Buzzer Electronic Control Modules Engine Systems Heated Systems Horn Ignition Control Instrument Cluster Lamps Power Systems Restraints Speed Control Vehicle Theft Security Wipers/Washers Wiring Engine Exhaust System Frame & Bumpers Fuel System Steering Transmission Tires/Wheels Body Heating & Air Conditioning Emissions Control Component and System Index

Service Manual Comment Forms

(Rear of Manual)

VA

INTRODUCTION

1

INTRODUCTIONTABLE OF CONTENTSpage VEHICLE IDENTIFICATION NUMBER DESCRIPTION . . . . . . . . . . . . . . . . INTERNATIONAL SYMBOLS DESCRIPTION . . . . . . . . . . . . . . . . FASTENER IDENTIFICATION DESCRIPTION . . . . . . . . . . . . . . . . FASTENER USAGE DESCRIPTION - FASTENER USAGE page THREADED HOLE REPAIR DESCRIPTION - THREADED HOLE REPAIR . . . . 6 METRIC SYSTEM DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . 6 TORQUE REFERENCES DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . 9

..........1 ..........2 ..........3 .........6

VEHICLE IDENTIFICATION NUMBERDESCRIPTIONThe Vehicle Identification Number (VIN) plate is located on the lower windshield fence next to the left a-pillar. The VIN contains 17 characters that provide data concerning the vehicle. Refer to the VIN DECODING INFORMATION table to determine the identification of a vehicle.

To protect the consumer from theft and possible fraud the manufacturer is required to include a Check Digit at the ninth position of the Vehicle Identification Number. The check digit is used by the manufacturer and government agencies to verify the authenticity of the vehicle and official documentation. The formula to use the check digit is not released to the general public.

VIN DECODING INFORMATIONPOSITION INTERPRETATION CODE = DESCRIPTION WDX = Incomplete vehicle / Dodge WD1 = Incomplete vehicle / Dodge WD0 = Truck / Dodge WD2 = Truck / Dodge WD5 = Multi-purpose passenger vehicle / Dodge WD8 = Multi-purpose passenger vehicle / Dodge WDW = Bus / Dodge WDP = Incomplete vehicle / Freightliner WDY = Truck / Freightliner WDR = Multi-purpose passenger vehicle / Freightliner WD3 = Truck / Mercedes-Benz WD4 = Multi-purpose vehicle / Mercedes-Benz WD9 = Incomplete vehicle / Mercedes-Benz B = All 4x2 vehicle types / Canada P = All 4x2 vehicle types / USA X = 4x2 Chassis-cab Y = 4x2 Truck W = 4x2 Multi-purpose passenger vehicle

1, 2 & 3

World Manufacturer Code

4

Model

2

INTRODUCTION

VA

POSITION

INTERPRETATION

CODE = DESCRIPTION D1 = Sprinter, 3000 mm (118 lbs. class G D2 = Sprinter, 3550 mm (140 lbs. class G D3 = Sprinter, 4025 mm (158 lbs. class G D4 = Sprinter, 3550 mm (140 14,000 lbs. Class H D5 = Sprinter, 4025 mm (158 14,000 lbs. Class H D6 = Sprinter, 3567 mm (140 Van 8,001 to 9,000 lbs. class D7 = Sprinter, 4042 mm (159 Van 8,001 to 9,000 lbs. class 41 42 43 44 = = = = 2.7L 2.7L 2.7L 2.7L 5 5 5 5 in.) wheelbase, 8,001 up to 9,000 in.) wheelbase, 8,001 up to 9,000 in.) wheelbase, 8,001 up to 9,000 in.) wheelbase, Van 10,001 up to in.) wheelbase, Van 10,001 up to in.) in connection with 16 wheels, G in.) in connection with 16 wheels, G Diesel Diesel Diesel Diesel 612 612 647 647 (ME9) (MF1) (MC0) (MF2)

5 & 6

Model, Cab, Weight

7 & 8

Engine

cyl. cyl. cyl. cyl.

9 10 11 12 Thru 17 Model Year Assembly Plant

Check Digit 6 = 2006 5 = Dsseldorf Plant, Germany Vehicle Build Sequence

INTERNATIONAL SYMBOLSDESCRIPTIONThe graphic symbols illustrated in the following International Control and Display Symbols Chart (Fig. 1) are used to identify various instrument controls. The symbols correspond to the controls and displays that are located on the instrument panel.

VA

INTRODUCTION

3

Fig. 1 INTERNATIONAL CONTROL AND DISPLAY SYMBOLS1 2 3 4 5 6 7 8 9 10 11 12 High Beam Fog Lamps Headlamp, Parking Lamps, Panel Lamps Turn Warning Hazard Warning Windshield Washer Windshield Wiper Windshield Wiper and Washer Windscreen Demisting and Defrosting Ventilating Fan Rear Window Defogger Rear Window Wiper 13 14 15 16 17 18 19 20 21 22 23 24 Rear Window Washer Fuel Engine Coolant Temperature Battery Charging Condition Engine Oil Seat Belt Brake Failure Parking Brake Front Hood Rear hood (Decklid) Horn Lighter

FASTENER IDENTIFICATIONDESCRIPTIONThe SAE bolt strength grades range from grade 2 to grade 8. The higher the grade number, the greater the bolt strength. Identification is determined by the line marks on the top of each bolt head. The actual bolt strength grade corresponds to the number of line marks plus 2. The most commonly used metric bolt strength classes are 9.8 and 10.9. The metric strength class identification number is imprinted on the head of the bolt. The higher the class number, the greater the bolt strength. Some metric nuts are imprinted with a single-digit strength class on the nut face. Refer to the Fastener Identification and Fastener Strength Charts (Fig. 2) and (Fig. 3).

4

INTRODUCTION

VA

Fig. 2 FASTENER IDENTIFICATION

VA

INTRODUCTION

5

Fig. 3 FASTENER STRENGTH

6

INTRODUCTION

VA

FASTENER USAGEDESCRIPTION - FASTENER USAGEWARNING: USE OF AN INCORRECT FASTENER MAY RESULT IN COMPONENT DAMAGE OR PERSONAL INJURY. Fasteners and torque specifications references in this Service Manual are identified in metric and SAE format. During any maintenance or repair procedures, it is important to salvage all fasteners (nuts, bolts, etc.) for reassembly. If the fastener is not salvageable, a fastener of equivalent specification must be used.

METRIC SYSTEMDESCRIPTIONThe metric system is based on quantities of one, ten, one hundred, one thousand and one million. The following chart will assist in converting metric units to equivalent English and SAE units, or vise versa.

THREADED HOLE REPAIRDESCRIPTION - THREADED HOLE REPAIRMost stripped threaded holes can be repaired using a Helicoil . Follow the vehicle or Helicoil recommendations for application and repair procedures.

CONVERSION FORMULAS AND EQUIVALENT VALUESMULTIPLY in-lbs ft-lbs Inches Hg (60 F) psi Inches Feet Yards mph Feet/Sec mph Kilometers/Hr. (Km/h) BY x 0.11298 x 1.3558 x 3.377 x 6.895 x 25.4 x 0.3048 x 0.9144 x 1.6093 x 0.3048 x 0.4470 x 0.27778 TO GET = Newton Meters (Nm) = Newton Meters (Nm) = Kilopascals (kPa) = Kilopascals (kPa) = Millimeters (mm) = Meters (M) = Meters = Kilometers/Hr. (Km/h) = Meters/Sec (M/S) = Meters/Sec (M/S) = Meters/Sec (M/S) Nm Nm kPa kPa mm M M Km/h M/S M/S M/S MULTIPLY BY x 8.851 x 0.7376 x 0.2961 x 0.145 x 0.03937 x 3.281 x 1.0936 x 0.6214 x 3.281 x 2.237 x 3.600 TO GET = in-lbs = ft-lbs = Inches Hg = psi = Inches = Feet = Yards = mph = Feet/Sec = mph Kilometers/Hr. (Km/h)

VA

INTRODUCTION

7

COMMON METRIC EQUIVALENTS1 inch = 25 Millimeters 1 Foot = 0.3 Meter 1 Yard = 0.9 Meter 1 Mile = 1.6 Kilometers Refer to the Metric Conversion Chart to convert torque values listed in metric Newton-meters (Nm). Also, use the chart to convert between millimeters (mm) and inches (in.) (Fig. 4). 1 Cubic Inch = 16 Cubic Centimeters 1 Cubic Foot = 0.03 Cubic Meter 1 Cubic Yard = 0.8 Cubic Meter

8

INTRODUCTION

VA

Fig. 4 METRIC CONVERSION CHART

VA

INTRODUCTION

9

TORQUE REFERENCESDESCRIPTIONIndividual Torque Charts appear within many of the Groups. Refer to the Standard Torque Specifications Chart for torque references not listed in the individual torque charts (Fig. 5).

10

INTRODUCTION

VA

Fig. 5 TORQUE SPECIFICATIONS

VA

LUBRICATION & MAINTENANCE

0-1

LUBRICATION & MAINTENANCETABLE OF CONTENTSpage FLUID TYPES DESCRIPTION PARTS AND LUBRICANT RECOMMENDATIONS . . . . . . . . . . . . . . . . AUTOMATIC TRANSMISSION FLUID - NAG1 AXLE FLUID . . . . . . . . . . . . . . . . . . . . . . . BRAKE FLUID . . . . . . . . . . . . . . . . . . . . . . HOAT COOLANT . . . . . . . . . . . . . . . . . . . . ENGINE OIL - DIESEL ENGINES . . . . . . . . FUEL REQUIREMENTS - DIESEL ENGINE POWER STEERING FLUID . . . . . . . . . . . . OPERATION - AUTOMATIC TRANSMISSION FLUID . . . . . . . . . . . . . . . . . . . . . . . . . . . . FLUID CAPACITIES SPECIFICATIONS - FLUID CAPACITIES . . . . FLUID FILL/CHECK LOCATIONS INSPECTION - FLUID FILL/CHECK LOCATIONS ....................... HOISTING STANDARD PROCEDURE - HOISTING . . . . . JUMP STARTING STANDARD PROCEDURE - JUMP STARTING TOWING STANDARD PROCEDURE - TOWING . . . . . . MAINTENANCE SCHEDULES DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . INTERNATIONAL SYMBOLS DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . page

...5 ...5 ..6 ...7 ...8 ...9

...1 .1 ...2 ...2 ...2 ...3 ...4 ...5 ...5 ...5

FLUID TYPESDESCRIPTION PARTS AND LUBRICANT RECOMMENDATIONSLubricating grease is rated for quality and usage by the NLGI. All approved products have the NLGI symbol (Fig. 1) on the label. At the bottom NLGI symbol is the usage and quality identification letters. Wheel bearing lubricant is identified by the letter G. Chassis lubricant is identified by the latter L. The letter following the usage letter indicates the quality of the lubricant. The following symbols indicate the highest quality.

AUTOMATIC TRANSMISSION FLUID - NAG1NOTE: Refer to Service Procedures in this group for fluid level checking procedures. Use ATF approved to MB 236.10, MB 236.12, such as Shell ATF 3403/M-115, MOPAR part number 05127382AA, Fuchs/Shell ATF 3353, or equivalent. Automatic Transmission Fluid (ATF) is red in color when new. The ATF is dyed red so it can be identified from other fluids used in the vehicle such as engine oil or antifreeze. The red color is not permanent and is not an indicator of fluid condition. As the vehicle is driven, the ATF will begin to look darker in color and may eventually become brown. This is normal.

FLUID ADDITIVESDaimlerChrysler strongly recommends against the addition of any fluids to the transmission, other than those automatic transmission fluids listed above. Exceptions to this policy are the use of special dyes to aid in detecting fluid leaks. Various special additives and supplements exist that claim to improve shift feel and/or quality. These additives and others also claim to improve converter clutch operation and inhibit overheating, oxidation, varnish, and sludge. These claims have not been supported to the satisfaction of DaimlerChrysler and these additives must not be used. The use of transmission sealers should also be avoided, since they may adversely affect the integrity of transmission seals.

Fig. 1 NLGI Symbol1 - WHEEL BEARINGS 2 - CHASSIS LUBRICATION 3 - CHASSIS AND WHEEL BEARINGS

When service is required, DaimlerChrysler Corporation recommends that only MOPAR brand parts, lubricants and chemicals be used. MOPAR provides the best engineered products for servicing DaimlerChrysler Corporation vehicles.

0-2

LUBRICATION & MAINTENANCE

VACoolant with the HOAT inhibitor system. This coolant offers the best engine cooling without corrosion when mixed with 50% anti-freeze and 50% distilled water to obtain a freeze point of -37C (-34F). If it loses color or becomes contaminated, drain, flush, and replace with fresh properly mixed coolant solution. CAUTION: This coolant may not be mixed with any other type of antifreeze. Mixing of coolants other than specified (non-HOAT), may result in engine damage that may not be covered under the new vehicle warranty, and decreased corrosion protection. CAUTION: Do not use coolant additives that are claimed to improve engine cooling.

AXLE FLUIDUse oils approved to MB 235.0 or 235.6, such as Shell Spirax MB90, Caltex Hypoid LD, or MOPAR part number 4874469, or equivalent. An API GL-5/ MIL-2105-E SAE 90 Hypoid Gear Oil may be substituted. Reduced axle durability may result if an unapproved product is used.

BRAKE FLUIDUse brake fluid approved to MB 331.0, such as Intac B026D, MOPAR Brake & Clutch Fluid, part number 04549625AC, or equivalent. If the approved product is not available, use a DOT 4 brake fluid: minimum dry boiling point (ERBP) 500F, minimum wet boiling point (WERBP) 356F, maximum viscosity 1500 mm2/s, conforming to FMVSS 116 and ISO 4925.

HOAT COOLANTWARNING: ANTIFREEZE IS AN ETHYLENE-GLYCOL BASE COOLANT AND IS HARMFUL IF SWALLOWED OR INHALED. IF SWALLOWED, DRINK TWO GLASSES OF WATER AND INDUCE VOMITING. IF INHALED, MOVE TO FRESH AIR AREA. SEEK MEDICAL ATTENTION IMMEDIATELY. DO NOT STORE IN OPEN OR UNMARKED CONTAINERS. WASH SKIN AND CLOTHING THOROUGHLY AFTER COMING IN CONTACT WITH ETHYLENE-GLYCOL. KEEP OUT OF REACH OF CHILDREN. DISPOSE OF GLYCOL BASE COOLANT PROPERLY, CONTACT YOUR DEALER OR GOVERNMENT AGENCY FOR LOCATION OF COLLECTION CENTER IN YOUR AREA. DO NOT OPEN A COOLING SYSTEM WHEN THE ENGINE IS AT OPERATING TEMPERATURE OR HOT UNDER PRESSURE, PERSONAL INJURY CAN RESULT. AVOID RADIATOR COOLING FAN WHEN ENGINE COMPARTMENT RELATED SERVICE IS PERFORMED, PERSONAL INJURY CAN RESULT. CAUTION: Use of Propylene-Glycol based coolants is not recommended, as they provide less freeze protection and less corrosion protection. The cooling system is designed around the coolant. The coolant must accept heat from engine metal, in the cylinder head area near the exhaust valves and engine block. Then coolant carries the heat to the radiator where the tube/fin radiator can transfer the heat to the air. The use of aluminum cylinder blocks, cylinder heads, and water pumps requires special corrosion protection. Use coolant approved to MB 325.0, such as EURO Peak Coolant/Anti-freeze (OLD WORLD INDUSTRIES), Zerex G05 or G48 (The Valvoline Company), Glysantin G05 (BASF AG), MOPAR part number 05066386AA, or an equivalent Extended Life

COOLANT PERFORMANCEThe required ethylene-glycol (antifreeze) and water mixture depends upon climate and vehicle operating conditions. The coolant performance of various mixtures follows: Pure Water-Water can absorb more heat than a mixture of water and ethylene-glycol. This is for purpose of heat transfer only. Water also freezes at a higher temperature and allows corrosion. 100 percent Ethylene-Glycol-The corrosion inhibiting additives in ethylene-glycol need the presence of water to dissolve. Without water, additives form deposits in system. These act as insulation causing temperature to rise. The increased temperature can result in engine detonation. In addition, 100 percent ethylene-glycol freezes at -22C (-8F). 50/50 Ethylene-Glycol and Water-Is the recommended mixture, it provides protection against freezing to -37C (-34F). The antifreeze concentration must always be a minimum of 44 percent, yearround in all climates. If percentage is lower, engine parts may be eroded by cavitation. Maximum protection against freezing is provided with a 68 percent antifreeze concentration, which prevents freezing down to -67.7C (-90F). A higher percentage will freeze at a warmer temperature. Also, a higher percentage of antifreeze can cause the engine to overheat because specific heat of antifreeze is lower than that of water. CAUTION: Richer antifreeze mixtures cannot be measured with normal field equipment and can cause problems associated with 100 percent ethylene-glycol.

VA

LUBRICATION & MAINTENANCEDaimlerChrysler Approved Engine Oil Agip Eurosport Agip Synthetic PC Akron Ultra Clear C1-4 (1) BP Vanellus C6 Global Plus Brad Penn Euro-Diesel LD Castrol Elixion (1) Castrol Tection S (1) Chevron Delo 400 Multigrade Diesel Special Benz M&A Dislub Premium Exxon XD-3 Extra (1) FormulaShell Ultra FormulaShell Ultra AB Gonher Super Fleet MB-III Hydroclear Power-D Engine Oil IDO Premium 15W-40 Kendall GT-1 Full Synthetic Motor Oil SAE Rating

0-3

ENGINE OIL - DIESEL ENGINESSAE VISCOSITY GRADECAUTION: Low viscosity oils must have the proper API quality. Only use engine oils that are labeled on the container as meeting API (American Petroleum Institute) and/or DaimlerChrysler specifications MB 228.3, 228.5, 229.3, and 229.5, such as MOPAR SAE 15W-40 HD Diesel Engine Oil (e.g. MOPAR Part No. 03798231AD), or equivalent. Do not add any materials (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives. When topping off engine oil, only use oil of the same quality grade and SAE classification. Always refer to the following viscosity chart for the proper viscosity grade based on ambient temperature. Select oil viscosity according to the lowest air temperature expected before the next oil change. The temperature limits given for the different SAE classes should be regarded as guidelines which may be exceeded temporarily to avoid excessively frequent engine oil changes.

MB Sheet Number 229.3 229.3 228.3 228.3 228.3 228.5 228.3 228.3 228.3 228.3 228.3 229.3 229.5 228.3 228.3

5W-40 5W-40 15W-40 10W-40 15W-40 5W-40 15W-40 15W-40 15W-40 15W-40 15W-40 5W-40 5W-30 15W-40 15W-40

15W-40 5W-40

228.3 229.3

OIL VISCOSITY CHARTThe following engine oils have been determined to meet DaimlerChrysler requirements: DaimlerChrysler Approved Engine Oil 76 Pure Synthetic Motor Oil 76 Royal Triton QLT Agip All Guard Motor Oil SAE Rating MB Sheet Number 229.3 228.3 228.3

Long Life EF Diesel Engine Oil Multigrade Lubral Super Diesel MB-III Max Raloy Diesel MB Motorenl 000 989 60 01 13 Mexlub CF-4 MB-3P Mobil 1 0W-40

15W-40

228.3

15W-40 5W-30 10W-40

228.3 228.5 228.5

5W-40 15W-40 15W-40

15W-40 0W-40

228.3 229.5

0-4

LUBRICATION & MAINTENANCESAE Rating MB Sheet Number 228.5 228.3 229.5 228.3 DaimlerChrysler Approved Engine Oil Shell Rotella T Multigrade (1) Super Diesel Oil MB-3 Supreme Duty Diesel Engine Oil Multi- grade Unoil GX-7 0W-40 5W-40 5W-40 5W-30 229.3 229.3 229.3 229.5 Ursa Premium TDX Ursa Premium TDX Valvoline SynPower MXL SAE Rating

VAMB Sheet Number 228.3 228.3 228.3

DaimlerChrysler Approved Engine Oil Mobil Delvac 1 Mobil Delvac 1300 Super (1) Mobil SHC Formula MB MOPAR Part No. 04798231AD Motul 8100 ETech 0W-40 Motul 8100 Xcess 5W-40 Panolin Indy SV Pennzoil European Formula Ultra Pennzoil Synthetic European Formula Premium Synthetik Motorenl QS Superfleet Quaker State European Formula Ultra Quaker State Full Synthetic European Formula Quaker State Super Series III (1) Raloy Diesel Turbo MX Raloy Motor Diesel Repsol Turbo UHPD Roshfrans Voltro Diesel (1) Shell Helix Ultra Shell Helix Ultra Shell Rimula X CH-4 Shell Rimula X CH-4

5W-40 15W-40 5W-30 15W-40

15W-40 15W-40 15W-40

5W-40 10W-30 15W-40 0W-30

229.3 228.3 228.3 229.3

5W-40

229.3

(1) Engine oil also meets API classification CI-4. Other oils may meet requirements - see oil label to determine Use of the approved fluid is required if the ASSYST Oil Service Reminder is followed. Use of a lower quality oil on this service schedule may cause severe engine damage.

5W-30 15W-40 5W-30

229.5 228.3 229.5

FUEL REQUIREMENTS - DIESEL ENGINEWARNING: Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel. Use only commercially available vehicular diesel fuels No. 2 or No. 1 (ASTM D 975 No. 2-D or No. 1-D). NOTE: Because of its better quality, the manufacturer recommends the use of commercially available vehicular diesel fuel No. 2.

5W-40

229.3

15W-40

228.3

15W-40 15W-40 10W-40 15W-40 5W-30 5W-40 15W-40 20W-50

228.3 228.3 228.5 228.3 229.3 229.3 228.3 228.3

DIESEL FUELS FOR USE AT VERY LOW TEMPERATUREAt very low temperatures, the fluidity of No. 2 diesel fuel may become insufficient due to paraffin seperation. For this reason, the vehicle comes equipped with a fuel preheater. It permits trouble free engine operation to a temperature of approximately 14F (-10C) when using No. 2 diesel fuel. To avoid malfunctions, No. 2 diesel fuel of a lowered cloud point is marketed during the cold season. At temperatures below 14 F (-10 C) use winterized or No. 1 diesel fuel only.

VADo not blend other specific fuel additives with diesel fuel. They only result in unnecessary cost, and may be harmful to the engine operation.

LUBRICATION & MAINTENANCEDESCRIPTION

0-5

SPECIFICATION

POWER STEERING SYSTEM Power steering fluid capacities are dependent on engine/chassis options as well as steering gear/cooler options. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these capacities may vary. Refer to 19, Steering for proper fill and bleed procedures.

POWER STEERING FLUIDNo fluid service required. Filled with Power Steering Fluid approved to MB 236.3, such as Mobil ATF-D (Exxon Mobil Corporation) or equivalent.

OPERATION - AUTOMATIC TRANSMISSION FLUIDThe automatic transmission fluid is selected based upon several qualities. The fluid must provide a high level of protection for the internal components by providing a lubricating film between adjacent metal components. The fluid must also be thermally stable so that it can maintain a consistent viscosity through a large temperature range. If the viscosity stays constant through the temperature range of operation, transmission operation and shift feel will remain consistent. Transmission fluid must also be a good conductor of heat. The fluid must absorb heat from the internal transmission components and transfer that heat to the transmission case.

FLUID FILL / CHECK LOCATIONSINSPECTION - FLUID FILL / CHECK LOCATIONSThe fluid fill/check locations and lubrication points are located in each applicable group.

HOISTINGSTANDARD PROCEDURE - HOISTINGRefer to the Owners Manual for emergency vehicle lifting procedures. WARNING: THE HOISTING AND JACK LIFTING POINTS PROVIDED ARE FOR A COMPLETE VEHICLE. WHEN A CHASSIS OR DRIVETRAIN COMPONENT IS REMOVED FROM A VEHICLE, THE CENTER OF GRAVITY IS ALTERED MAKING SOME HOISTING CONDITIONS UNSTABLE. PROPERLY SUPPORT OR SECURE VEHICLE TO HOISTING DEVICE WHEN THESE CONDITIONS EXIST.

FLUID CAPACITIESSPECIFICATIONS - FLUID CAPACITIESDESCRIPTION 10 Liters ENGINE OIL 9.0L without Filter Replacement Service Fill - NAG1 O-haul Fill - NAG1 9.5 Quarts with Filter Replacement 5.0 L (10.6 pts.) 7.7 L (16.3 pts.) SPECIFICATION 10.5 Quarts ENGINE COOLANT

AUTOMATIC TRANSMISSION

FLOOR JACKWhen properly positioned, a floor jack can be used to lift a vehicle. Support the vehicle in the raised position with jack stands at the front and rear ends of the frame rails. CAUTION: Do not lift vehicle with a floor jack positioned under: An axle tube. A body side sill. A steering linkage component. A drive shaft. The engine or transmission oil pan. The fuel tank. A front suspension arm.

Dry fill capacity Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. (Refer to appropriate 21 - TRANSMISSION/AUTOMATIC/FLUID - STANDARD PROCEDURE). REAR AXLE .03L (1 oz.) 8 1/2 FUEL TANK Primary Reserve 100 L (26.4 gal.)* 10.5 L (2.8 gal.)* 1.8 L (4.0 pts.)

*Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure

0-6 HOISTA

LUBRICATION & MAINTENANCE

VA IF EQUIPPED, DO NOT JUMP START WHEN MAINTENANCE FREE BATTERY INDICATOR DOT IS YELLOW OR BRIGHT COLOR. DO NOT JUMP START A VEHICLE WHEN THE BATTERY FLUID IS BELOW THE TOP OF LEAD PLATES. DO NOT ALLOW JUMPER CABLE CLAMPS TO TOUCH EACH OTHER WHEN CONNECTED TO A BOOSTER SOURCE. DO NOT USE OPEN FLAME NEAR BATTERY. REMOVE METALLIC JEWELRY WORN ON HANDS OR WRISTS TO AVOID INJURY BY ACCIDENTAL ARCING OF BATTERY CURRENT. WHEN USING A HIGH OUTPUT BOOSTING DEVICE, DO NOT ALLOW BATTERY VOLTAGE TO EXCEED 16 VOLTS. REFER TO INSTRUCTIONS PROVIDED WITH DEVICE BEING USED. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CAUTION: When using another vehicle as a booster, do not allow vehicles to touch. Electrical systems can be damaged on either vehicle.

vehicle can be lifted with: A single-post, frame-contact hoist. A twin-post, chassis hoist. A ramp-type, drive-on hoist.

NOTE: When a frame-contact type hoist is used, verify that the lifting pads are positioned properly. The forward lifting pads should be positioned against the forward flange of the transmission crossmember brackets at the bottom of the frame rail. The real lifting pads should be wedged between the forward flange of the leaf spring bracket and the frame rail. Safety stands should be placed under the frame rails at the front and rear ends.

TO JUMP START A DISABLED VEHICLE:(1) Raise hood on disabled vehicle and visually inspect engine compartment for: Battery cable clamp condition, clean if necessary. Frozen battery. Yellow or bright color test indicator, if equipped. Low battery fluid level. Generator drive belt condition and tension. Fuel fumes or leakage, correct if necessary. CAUTION: If the cause of starting problem on disabled vehicle is severe, damage to booster vehicle charging system can result.

Fig. 2 HOIST LOCATIONS1 - TRANSMISSION CROSSMEMBER SUPPORT 2 - REAR LEAF SPRING MOUNT - FRONT 3 - TRANSMISSION CROSSMEMBER

JUMP STARTINGSTANDARD PROCEDURE - JUMP STARTINGWARNING: REVIEW ALL SAFETY PRECAUTIONS AND WARNINGS IN THE BATTERY SYSTEM SECTION OF THE SERVICE MANUAL. (Refer to 8 ELECTRICAL/BATTERY SYSTEM/BATTERY - STANDARD PROCEDURE) DO NOT JUMP START A FROZEN BATTERY, PERSONAL INJURY CAN RESULT.

(2) When using another vehicle as a booster source, park the booster vehicle within cable reach. Turn off all accessories, set the parking brake, place the automatic transmission in PARK or the manual transmission in NEUTRAL and turn the ignition OFF. (3) On disabled vehicle, place gear selector in park or neutral and set park brake. Turn off all accessories. (4) Connect jumper cables to booster battery. RED clamp to positive terminal (+). BLACK clamp to negative terminal (-). DO NOT allow clamps at opposite end of cables to touch, electrical arc will result. Review all warnings in this procedure. (5) On disabled vehicle, connect RED jumper cable clamp to positive (+) terminal. Connect BLACK jumper cable clamp to engine ground as close to the ground cable attaching point as possible.

VA(6) Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. CAUTION: Do not crank starter motor on disabled vehicle for more than 15 seconds, starter will overheat and could fail. (7) Allow battery in disabled vehicle to charge to at least 12.4 volts (75% charge) before attempting to start engine. If engine does not start within 15 seconds, stop cranking engine and allow starter to cool (15 min.), before cranking again.

LUBRICATION & MAINTENANCE If the Front Axle is Damaged

0-7

Raise the front axle. Observe the same towing restrictions as for engine damage.

If the Rear Axle is Damaged Raise the rear axle. NOTE: Comply with local legal regulations regarding towing vehicles.

SAFETY PRECAUTIONSNOTE: The following safety precautions must be observed when towing a vehicle. Secure loose and protruding parts. Always use a safety chain system that is independent of the lifting and towing equipment. Do not allow towing equipment to contact the disabled vehicles fuel tank. Do not allow anyone under the disabled vehicle while it is lifted by the towing device. Do not allow passengers to ride in a vehicle being towed. Always observe state and local laws regarding towing regulations. Do not tow a vehicle in a manner that could jeopardize the safety of the operator, pedestrians or other motorists. Do not attach tow chains, T-hooks, J-hooks, or a tow sling to a bumper, steering linkage, drive shafts or a non-reinforced frame hole. Remove exhaust pipe tips that interfere with the tow sling and crossbar Padding should be placed between the tow sling/ crossbar and any painted surfaces When placing tow hooks on the rear axle, position them so they do not damage the brake tubing or hoses Do not tow the vehicle by connecting to the front or rear shock absorbers Do not tow a heavily loaded vehicle. Damage to the vehicle may result. Use a flatbed device to transport a loaded vehicle.

DISCONNECT CABLE CLAMPS AS FOLLOWS: Disconnect BLACK cable clamp from engine ground on disabled vehicle. When using a Booster vehicle, disconnect BLACK cable clamp from battery negative terminal. Disconnect RED cable clamp from battery positive terminal. Disconnect RED cable clamp from battery positive terminal on disabled vehicle.

TOWINGSTANDARD PROCEDURE - TOWINGWARNING: Do not tow the vehicle if the key cannot be turned in the ignition lock. If the key cannot be turned, the ignition lock remains locked and the vehicle cannot be steered. With the engine not running there is no power assistance for the braking and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. The vehicle must not be towed with the front axle raised and the key in position 2 in the ignition lock as the drive wheels could then lock due to the acceleration skid control (ASR)

If the Engine is DamagedFor towing distances up to 30 miles (about 50 km) Shift selector lever in N position. Do not exceed a towing speed of 30 m.p.h. (50 km/h). For towing distances greater than 30 mile (about 50 km) Remove the propeller shafts leading to the drive axles. The vehicle can be towed without restriction.

GROUND CLEARANCECAUTION: If vehicle is towed with wheels removed, install lug nuts to retain brake drums. A towed vehicle should be raised until lifted wheels are a minimum 100 mm (4 in) from the ground. Be sure there is adequate ground clearance at the opposite end of the vehicle, especially when towing over rough terrain, steep rises in the road or if the vehicle is equipped with air dams, spoilers, and/or ground

If the Transmission is Damaged Remove the propeller shafts leading to the drive axles. The vehicle can be towed without restriction.

0-8

LUBRICATION & MAINTENANCE

VAYou should have the maintenance performed within the stated period/distance. The service indicator will be reset after an oil service and/or maintenance service has been performed.

effect panels. If necessary, remove the wheels from the lifted end of the vehicle and lower the vehicle closer to the ground, to increase the ground clearance at the opposite end of the vehicle. Install lug nuts on wheel attaching studs to retain brake drums.

REGULAR CHECK - UPS RAMP ANGLEIf a vehicle with flat-bed towing equipment is used, the approach ramp angle should not exceed 15 degrees. To maintain the safe operation of the vehicle, it is recommended that the following tasks be performed on a regular basis (i.e. weekly or whenever the vehicle is refueled). Check: Engine oil level Brake system - fluid level Battery - acid level Windshield washer system and headlamp cleaning system - fluid level Mechanical assemblies (e.g. engine, transmission, etc.) - check for leaks Condition of tires and tires pressures All exterior lights

TOWING WHEN KEYS ARE NOT AVAILABLEWhen the vehicle is locked and keys are not available, use a flat bed hauler. A Wheel-lift or Sling-type device can be used provided all the wheels are lifted off the ground using tow dollies.

MAINTENANCE SCHEDULESDESCRIPTIONThe use of special lubricant additives is not recommended. The use of such additives may affect the warranty rights. With regard to legal stipulations concerning emissions control, please note that engines have to be serviced and adjusted in accordance with special instructions and using special measuring equipment. Modifications to or interference with the emissions control systems are not permissible.

SPECIAL MAINTENANCE REQUIREMENTSIf bodies built by manufacturers other than DaimlerChrysler Corporation are fitted to the vehicle, the maintenance requirements and lubrication intervals specified by the body manufacturer must be adhered to, in addition to all standard maintenance requirements. Coolant Corrosion inhibitor/antifreeze concentration in the coolant should be checked before the onset of winter (once year in countries with high prevailing temperatures). Replace the coolant every five years or 100,000 miles. Dust Filter for Heating / Ventilation Replacement The dust filter and the tailgate interior filter are to be renewed during routine maintenance service. If operating conditions are dusty, these filters should be renewed more frequently.

MAINTENANCE - WITHOUT ASSYST MAINTENANCE COMPUTERMaintenance Intervals Oil service Normal Operation every 10,000 miles or 16,000 km or 12 months. Maintenance service every 30,000 miles or 48,000 km. Additional work must be carried out at yearly intervals.

MAINTENANCE - WITH ASSYST MAINTENANCE COMPUTERASSYST provides information on the best possible timing for maintenance work. When the next maintenance service is due, this will be indicated in the multi-function display with the wrench icon symbol displayed in km/miles or days. One wrench icon showing indicates Oil Service is necessary. Two wrench icons showing indicates Maintenance Service is necessary displayed in km/miles or days. If the display shows the number of days, a clock symbol will also appear in the multi-function display.

ENGINE OIL CHANGE AND FILTER REPLACEMENTAt a minimum, change the engine oil and oil filter once a year even if the vehicle mileage per year is extremely low. For standard oil service schedules refer to the chapter oil service and maintenance service. Once a Year Select the viscosity of the engine oil (SAE classes) according to the outside air temperature. Only use engine oil approved by DaimlerChrysler Corporation if following the ASSYST system guidelines.

VA SCOPE OF WORK FOR MAINTENANCE SERVICEOil Service Engine: Oil change and filter replacement Check fluid levels of the following system, refill as necessary. If fluid is lost, trace and eliminate cause - as a separate order. Power-assisted steering Lubrication work: Trailer tow hitch (original equipment) Maintenance ASSYST maintenance computer reset Function check Signalling system, warning and indicator lamps Headlamps, exterior lighting Windshield wipers, windshield washer system Check for leaks and damage Check for abrasion points and ensure that lines are correctly routed! All lines and hoses, sensor cables Rubber boots on front axle drive shafts, rubber boots on front axle suspension ball joints, shock absorbers Check fluid levels for the following systems, correct as necessary NOTE: Should there be a loss of fluid which cannot be explained by regular use, trace and eliminate the cause. Engine cooling system. Check corrosion inhibitor/antifreeze, refill as necessary. Hydraulic brake system Battery Windshield washer system Engine Fuel filter renewal - Every oil service Air cleaner with maintenance indicator: Check degree of contamination. Air cleaner filter element renewed as necessary. Chassis and body Trailer coupling: Check operation, play and retaining fixtures Secondary rubber springs: Visual check Tire pressures: Correct as necessary, including spare tire Check thickness of brake pads Brake test Check condition of steering mechanism Heating/ventilation dust filter renewal

LUBRICATION & MAINTENANCE ADDITIONAL MAINTENANCE WORK

0-9

Automatic transmission once only at 80,000 miles / 128000 km Oil and filter change During every second maintenance service Air cleaner without maintenance indicator: Air cleaner filter element renewal Check poly-V-belt for wear and signs of damage During every fourth maintenance service Change rear axle fluid

ADDITIONAL MAINTENANCE WORK AFTER YEARSEvery 2 years Change brake fluid. Every 3 years Air cleaner filter element renewal (note installation date) Every 15 years or 100,000 miles Coolant renewal Note coolant composition

INTERNATIONAL SYMBOLSDESCRIPTIONDaimlerChrysler Corporation uses international symbols to identify engine compartment lubricant and fluid inspection and fill locations (Fig. 3).

Fig. 3 INTERNATIONAL SYMBOLS

VA

SUSPENSION

2-1

SUSPENSIONTABLE OF CONTENTSpage FRONT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 WHEEL ALIGNMENT page . . . . . . . . . . . . . . . . . . . . . . 17

FRONTTABLE OF CONTENTSpage FRONT SPECIFICATIONS - TORQUE CHART SPECIAL TOOLS FRONT SUSPENSION . . . . . . . . . BUSHINGS REMOVAL ................... INSTALLATION . . . . . . . . . . . . . . . . HUB / BEARING DIAGNOSIS AND TESTING ..... REMOVAL ................... INSTALLATION . . . . . . . . . . . . . . . . KNUCKLE REMOVAL ................... INSTALLATION . . . . . . . . . . . . . . . . LOWER BALL JOINT REMOVAL ................... INSTALLATION . . . . . . . . . . . . . . . . LOWER CONTROL ARM REMOVAL ................... INSTALLATION . . . . . . . . . . . . . . . . page SPRING REMOVAL .............................7 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SPRING CLAMP PLATES REMOVAL .............................8 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 9 SPRING STOP PLATES REMOVAL .............................9 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 9 STABILIZER BAR DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . 9 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 REMOVAL .............................9 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 9 STABILIZER LINK REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 10 STRUT REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 10

.........1 ..........2 ..........3 ..........3 ..........4 ..........4 ..........5 ..........5 ..........6 ..........6 ..........6 ..........6 ..........7

FRONTSPECIFICATIONS - TORQUE CHARTTORQUE SPECIFICATIONSDESCRIPTION Lower Ball Joint To Steering Knuckle Strut To Steering Knuckle Strut To Body Bottom Spring Clamp Plate To Front Axle M12 X 1.5 Bolt Nm 280 185 100 130 Ft. Lbs. 206 136 74 96 In. Lbs.

2-2

FRONTDESCRIPTION Nm 65 Ft. Lbs. 48 In. Lbs.

VA

Bottom Spring Clamp Plate To Front Axle M10 Bolt Sway Bar Clamp To The Front Axle Hexagon Socket Bolt For Clamping Nut To Adjust Wheel Bearing Play Lower Control Arm To Front Axle Beam Stop Plate For Lower Control Arm Outer Tie Rod End Nut Outer Tie Rod End Nut Jam Nut

30 12

22 9

106

150 60 130 50

110 44 96 37

SPECIAL TOOLS FRONT SUSPENSIONSPECIAL TOOL CROSS REFERENCE CHARTMB TOOL # N/A N/A N/A N/A 730 589 02 33 00 N/A MILLER TOOL # 9288 9294 9302 C-3894-A 9282 C-4212F DESCRIPTION LEAF SPRING WEDGE BLOCK LOWER BALL JOINT REMOVE/INSTALLER BUSHING REMOVER /INSTALLER PULLER TIE ROD BALL JOINT SEPARATOR BALL JOINT PRESS

BALL JOINT PRESS - C-4212F

LOWER BALL JOINT REMOVE / INSTALL - 9294

Puller Tie Rod C-3894-A

VA

FRONT

2-3

(3) Install special tool C-4212F (Press) with special tool 9302-1 (Driver) and 93023 (Receiver) (Fig. 1).

BALL JOINT SEPARATOR - 9282

Fig. 1 LCA BUSHING REMOVAL1 2 3 4 5 SPECIAL TOOL C-4212F (PRESS) SPECIAL TOOL 9302-1 (DRIVER) LOWER CONTROL ARM SPECIAL TOOL 9302-3 (RECEIVER CUP) BUSHING

(4) Press out the old control arm bushing.

LEAF SPRING WEDGE BLOCK - 9288

INSTALLATION(1) Install the new control arm bushing into the control arm. (2) Press the new bushing into the control arm using special tool C-4212F and 9302-1 (Driver) with 9302-2 (Sizer cup) and 9302-4 (Receiver) (Fig. 2). (3) Press the bushing in all the way until the lip is seated properly into the control arm. (4) Install the lower control arm to the vehicle (Refer to 2 - SUSPENSION/FRONT/LOWER CONTROL ARM - INSTALLATION).

BUSHING REMOVER / INSTALLER-9302

BUSHINGSREMOVAL(1) Remove the lower control arm (Refer to 2 SUSPENSION/FRONT/LOWER CONTROL ARM REMOVAL). (2) Install the lower control arm in a vise.

2-4

FRONT

VA

Fig. 2 LCA BUSHING INSTALL1 2 3 4 5 6 SPECIAL TOOL C-4212F (PRESS) SPECIAL TOOL 9302-1 (DRIVER) BUSHING SPECIAL TOOL 9302-2 (SIZER CUP) LOWER CONTROL ARM SPECIAL TOOL 9302-4 (RECEIVER CUP)

Fig. 3 MEASURING & ADJUSTING WHEEL BEARING1 - WHEEL HUB 2 - LOCKING SCREW 3 - DIAL INDICATOR

REMOVAL(1) Raise and support the vehicle. (2) Remove the front wheels (Refer to 22 - TIRES/ WHEELS/WHEELS - REMOVAL). (3) Remove the disc brake caliper adapter (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/DISC BRAKE CALIPER ADAPTER - REMOVAL). (4) Remove the wheel flange ring (if equipped with dual rear wheels) (Fig. 5). (5) Remove the disc brake rotor (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/ROTORS REMOVAL). (6) Remove the grease cap (Fig. 4). (7) Loosen the bolt on the clamping nut and remove the clamping nut (Fig. 4). (8) Remove the thrust washer (Fig. 4). (9) Remove the wheel hub and tapered roller bearing from the stub axle assembly (Fig. 4).

HUB / BEARINGDIAGNOSIS AND TESTING (1) Raise and support the vehicle. (2) Remove the grease cap. (3) Position a dial indicator against the face of the wheel hub (Fig. 3). (4) Tighten the locking screw on the clamping nut (Fig. 3). (5) Pull the wheel hub firmly back and forth and read off the wheel bearing play on the dial gauge. (Wheel bearing play should be 0.02 - 0.04 mm (0.000787 - 0.00158 in.). (6) If necessary, loosen the locking screw and adjust the wheel bearing play by loosing or tightening the clamping nut. (7) Retighten the locking screw and recheck the wheel bearing play.

VA

FRONT

2-5

INSTALLATION(1) Install the wheel hub with the tapered roller bearing on the stub axle (Fig. 4). (2) Grease the outer tapered roller bearing thoroughly and push onto the steering knuckle (Fig. 4). NOTE: The smooth side of the thrust washer must point toward the wheel bearing. (3) Install the thrust washer (Fig. 4). (4) Install the clamping nut (Fig. 4). Tighten to 12 Nm (9 ft. lbs.) and then loosen a half of a turn. (5) Check for wheel bearing end play. End play should be 0.02- 0.04 mm (0.000787 - 0.00158 in.) (Fig. 3) (Refer to 2 - SUSPENSION/FRONT/HUB / BEARING - DIAGNOSIS AND TESTING). (6) Pack the grease cap half with grease and coat at the edge with sealant and install the cap (Fig. 4). (7) Install the disc brake rotor (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/ROTORS INSTALLATION). (8) Install the disc brake caliper adapter (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/DISC BRAKE CALIPER ADAPTER - INSTALLATION). (9) Install the wheel flange ring (if equipped with dual rear wheels) (Fig. 5). (10) Install the front tire & wheels assembly (Refer to 22 - TIRES/WHEELS/WHEELS - INSTALLATION). (11) Lower the vehicle.

Fig. 4 FRONT WHEEL HUB WITH SINGLE REAR WHEELS (SRW)1 - CALIPER ADAPTER BOLT 2 - DISC BRAKE CALIPER 3 - INNER BEARING 4 - WHEEL HUB 5 - DISC BRAKE ROTOR 6 - OUTER BEARING 7 - THRUST WASHER 8 - CLAMPING NUT 9 - GREASE CAP 10 - LOCKING BOLT 11 - GREASE SEAL 12 - STEERING KNUCKLE

KNUCKLEREMOVAL(1) Raise and support the vehicle. (2) Remove the front wheels (Refer to 22 - TIRES/ WHEELS/WHEELS - REMOVAL). (3) Remove the disc brake caliper adapter (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/DISC BRAKE CALIPER ADAPTER - REMOVAL). (4) Remove the hub/bearing (Refer to 2 - SUSPENSION/FRONT/HUB / BEARING - REMOVAL). (5) Separate the outer tie rod from the steering knuckle (Fig. 6) using special tool C-3894A. (6) Raise the lower control arm approximately 10 mm using a jack. In order to eliminate tensile force in the damper strut. (7) Remove the ABS sensor from the knuckle by pulling straight out. (8) Remove the strut at the knuckle (Fig. 6). (9) Separate the lower ball joint from the steering knuckle using special tool 9282 (Fig. 6). (10) Remove the steering knuckle from the vehicle (Fig. 6).

Fig. 5 FRONT WHEEL HUB WITH DUAL REAR WHEELS (DRW)1 - ADAPTER BOLT 2 - DISC BRAKE CALIPER 3 - INNER BEARING RACE 4 - WHEEL HUB 5 - DISC BRAKE ROTOR 6 - LOCKING BOLT 7 - WHEEL FLANGE RING 8 - OUTER BEARING 9 - THRUST WASHER 10 - CLAMPING NUT 11 - GREASE CAP 12 - WHEEL FLANGE RING MOUNTING BOLT 13 - GREASE SEAL 14 - STEERING KNUCKLE

2-6

FRONT

VA(4) Remove the steering knuckle (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - REMOVAL). (5) Remove the lower ball joint using special tool 9294-1 (Driver) with 9294-2 (Reciever) and C-4212F. (Fig. 7).

Fig. 6 STEERING KNUCKLE1 2 3 4 5 6 7 STRUT STRUT BOLT STEERING KNUCKLE LOWER BALL JOINT NUT OUTER TIE ROD END RETAINING NUT INNER TIE ROD END LOWER CONTROL ARM

Fig. 7 LOWER BALL JOINT1 - LOWER CONTROL ARM 2 - LOWER BALL JOINT

INSTALLATION(1) Install the steering knuckle on the lower ball joint stud (Fig. 6). (2) Install the lower ball joint nut (Fig. 6). Tighten to 280 Nm (206 ft. lbs.) (3) Install the strut to the steering knuckle (Fig. 6). Tighten to 185 Nm (136 ft. lbs.). (4) Install the outer tie rod end to the steering knuckle (Fig. 6) and tighten the nut to 130 Nm (96 ft. lbs.). (5) Install the ABS sensor by pushing the sensor all the way into the knuckle and the sensor will self adjust when the wheel is turned. (6) Install the hub/bearing (Refer to 2 - SUSPENSION/FRONT/HUB / BEARING - INSTALLATION). (7) Install the disc brake caliper adapter with the brake caliper (Refer to 5 - BRAKES/HYDRAULIC/ MECHANICAL/DISC BRAKE CALIPER ADAPTER INSTALLATION). (8) Install the front wheels (Refer to 22 - TIRES/ WHEELS/WHEELS - INSTALLATION). (9) Lower the vehicle. (10) Check and set toe if necessary (Refer to 2 SUSPENSION/WHEEL ALIGNMENT - STANDARD PROCEDURE).

INSTALLATION(1) Install the ball joint into the lower control arm using special tool 9294-3 (Installer ring) inserted in 9294-2 (Reciever) and C-4212F (Fig. 7). (2) Install the front strut (Refer to 2 - SUSPENSION/FRONT/STRUT - INSTALLATION). (3) Install the steering knuckle (Refer to 2 - SUSPENSION/FRONT/KNUCKLE - INSTALLATION). (4) Install the tire and wheel assembly (Refer to 22 - TIRES/WHEELS/WHEELS - INSTALLATION). (5) Lower the vehicle. (6) Check the front wheel alignment (Refer to 2 SUSPENSION/WHEEL ALIGNMENT - SPECIFICATIONS).

LOWER CONTROL ARMREMOVAL(1) Insert spring blocks special tool 9288 between the spring and the spring clamp plates, While the vehicles wheels are on the ground. (2) Raise and support the vehicle. (3) Remove the front wheels (Refer to 22 - TIRES/ WHEELS/WHEELS - REMOVAL). (4) Remove the disc brake caliper adapter (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/DISC BRAKE CALIPER ADAPTER - REMOVAL). Hang the caliper. Do not allow brake hose to support the caliper weight. (5) Remove the retaining nut holding the tie rod to the steering knuckle (Fig. 8).

LOWER BALL JOINTREMOVAL(1) Raise and support the vehicle. (2) Remove the front tire and wheel assembly. (3) Remove the front strut (Refer to 2 - SUSPENSION/FRONT/STRUT - REMOVAL).

VA(6) Seperate the tie rod off the steering knuckle (Fig. 8) using special tool C-3894A. NOTE: In order to remove tension from the strut, Raise the lower control arm approximately 10 mm with a jack. (7) Remove the strut bolts from the steering knuckle (Fig. 8). (8) Remove the stop plate bolts and rotate the plate upwards with the stabilizer link attached (Fig. 8). (9) Lower the lower control arm. (10) Remove the lower ball joint nut from the steering knuckle (Fig. 8). (11) Separate the lower ball joint from the knuckle using special tool 9282. (12) Remove the lower control arm nuts and bolts from the frame (Fig. 8). (13) Remove the lower control arm.

FRONT

2-7

(2) Install the lower ball joint into the steering knuckle. Tighten to 280 Nm (206 ft. lbs.). (3) Install the strut bolts to the steering knuckle (Fig. 8). Tighten to 185 Nm (136 ft. lbs.). (4) Install the stop plate (Refer to 2 - SUSPENSION/FRONT/SPRING STOP PLATES - INSTALLATION). (5) Lower the lower control arm. (6) Attach the tie rod to the steering knuckle (Fig. 8). Tighten the nut to 130 Nm (96 ft. lbs.) (7) Install the disc brake caliper adapter (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/DISC BRAKE CALIPER ADAPTER - INSTALLATION) (Fig. 8). (8) Install the front tire & wheel assembly (Refer to 22 - TIRES/WHEELS/WHEELS - INSTALLATION). (9) Lower the vehicle. (10) Remove the spring blocks between the spring and the spring clamp plates, While the vehicles wheels are on the ground. (11) Roll the vehicle approximately 1 mm forwards and the backwards, and rock firmly. (12) Tighten the lower control arm nuts and bolts to the frame to 150 Nm (110 ft. lbs.) (Fig. 8). (13) Apply brake to actuate brake pressure.

SPRINGREMOVAL(1) To do this next step the vehicle must be on the ground. Remove the front and rear bolts on the left and right spring clamp plates (Fig. 9). (2) Raise and support the vehicle. (3) Remove the front wheels. (4) Remove the brake caliper adapter (Refer to 5 BRAKES/HYDRAULIC/MECHANICAL/DISC BRAKE CALIPER ADAPTER - REMOVAL). Do not allow the caliper to hang by the hose, support the caliper accordingly. (5) Remove the ABS sensor from the mounting bore in the steering knuckle (Fig. 9). (6) Remove the outer tie rod retaining nut and separate the tie rod from the knuckle (Fig. 9) using special tool C-3894A. NOTE: In order to remove tension from the strut, Raise the lower control arm approximately 10 mm with a jack. (7) Remove the strut bolts from the steering knuckle. (8) Remove both stop plate bolts and rotate the plates upwards with the stabilizer link attached. (9) Lower the lower control arm. (10) Remove the lower ball joint nut from the steering knuckle.

Fig. 8 LOWER CONTROL ARM1 - STRUT 2 - LOWER CONTROL ARM BOLT 3 - STOP PLATE BOLT 4 - STOP PLATE 5 - CALIPER ADPTER BOLT 6 - DISC BRAKE CALIPER 7 - LOCKING BOLT 8 - DISC BRAKE ROTOR 9 - OUTER TIE ROD END RETAINING NUT 10 - OUTER TIE ROD END 11 - LOWER BALL JOINT NUT 12 - LOWER BALL JOINT 13 - LOWER CONTROL ARM NUTS 14 - STRUT BOLT

INSTALLATION(1) Install the lower control arm to the frame. Hand tighten the nuts and bolts. NOTE: In order to remove tension from the strut, Raise the lower control arm approximately 10 mm with a jack.

2-8

FRONT

VA

(11) Separate the lower ball joint from the knuckle using special tool 9282. (12) Remove the lower control arm nuts and bolts from the frame. (13) Remove the lower control arm from the frame (Fig. 9). NOTE: To avoid damaging the transverse leaf spring, cushion the pad on the jack accordingly. (14) Support the transverse leaf spring in the center with a jack. (15) Remove the left and right spring clamp plates (Refer to 2 - SUSPENSION/FRONT/SPRING CLAMP PLATES - REMOVAL) (Fig. 9). NOTE: The upper spring blocks between the engine cradle and the spring are color coded, Make sure not to mix the blocks per sides. The blocks are different in sizes to accommodate the weight of the vehicle and driver in order for the vehicle to sit level. (16) Lower the jack and remove the transverse leaf spring towards the side.

INSTALLATIONNOTE: To avoid damaging the transverse leaf spring, cushion the pad on the jack accordingly. NOTE: Hand tighten all bolts until vehicle is on the ground, unless the bushings may become distorted. NOTE: The height blocks between the engine cradle and the spring are color coded, Make sure not to mix the blocks per sides. The blocks are different in sizes to accommodate the weight of the vehicle and driver in order for the vehicle to sit level. (1) Install the transverse leaf spring in the center with a jack with all the rubber mounts attached. (2) Install the lower control arm to the frame (Fig. 9). (3) Install the knuckle on the lower ball joint. (4) Raise the lower control arm approximately 10 mm with a jack. (5) Install both stop plate bolts to the lower control arm (6) Install the strut bolts to the steering knuckle. (7) Reinstall the tie rod to the steering knuckle (Fig. 9). Tighten to 150 Nm (110 ft. lbs.). (8) Install the ABS sensor all the way into the steering knuckle, the sensor will adjust automatically when the vehicle is moved (Fig. 9). (9) Install the disc brake caliper adapter (Fig. 9). Tighten to 170 Nm (125 ft. lbs.). (10) Install the front wheels. (11) Lower the vehicle. (12) Install the spring clamp plates (Fig. 9). Tighten (M-10 bolts) to 65 Nm (48 ft. lbs.) (M-12 bolts) to 130 Nm (96 ft. lbs.). (13) Roll the vehicle approximately 1 mm forwards and the backwards, and rock firmly. (14) Tighten the nuts on the lower control arm to the frame to 150 Nm (110 ft. lbs.). (15) Apply brake to actuate brake pressure.

Fig. 9 FRONT SPRING1 - NUT 2 - STRUT 3 - STOP PLATE 4 - STOP PLATE BOLT 5 - CALIPER ADAPTER BOLT 6 - DISC BRAKE CALIPER 7 - OUTER TIE ROD END NUT 8 - ABS SENSOR 9 - SPEED SENSOR 10 - LOWER CONTROL ARM RETAINING NUTS 11 - OUTER TIE ROD END 12 - RUBBER SPRING MOUNT 13 - SHEAR BUSHING 14 - SPRING CLAMP PLATE BOLT 15 - SPRING CLAMP PLATE 16 - LOWER RUBBER SPRING MOUNT 17 - SPRING 18 - STRUT BOLTS 19 - LOWER CONTROL ARM BOLTS

SPRING CLAMP PLATESREMOVAL(1) Raise and support the vehicle. (2) Install a jack under the lower ball joint and lower the weight of the vehicle enough to allow a wrench between the lower control arm and the bracket tighten the nut. (3) Remove the front and rear bolts to the spring clamp plates. (4) Remove the four inner retaining bolts and nuts.

VA(5) Remove the spring clamp plate and rubber block. (6) Remove the shear bushings from the front and rear bolts.

FRONT

2-9

INSTALLATION(1) Install a jack under the lower ball joint and lower the weight of the vehicle enough to allow a wrench between the lower control arm and the bracket tighten the nut. (2) Fit one spring clamp plate together with the lower spring rubber block. (3) Install the bolt with the shear bushing on the rear mounting, Do not tighten yet. (4) Install the four retaining bolts for the spring clamp plate. Tighten to 65 Nm (48 ft.lbs.). (5) Align the holes for the front clamp plate joint using a suitable drift (shear bushing not installed). (6) Remove the alignment drift. (7) Insert the shear bushing and retaining bolt into the hole and tighten to 130 Nm (96 ft.lbs.). (8) Remove the jack and lower the vehicle.

Fig. 10 STABILIZER BAR

OPERATIONThe stabilizer bar is used to minimize vehicle front sway during turns. The bar helps to maintain a flat attitude to the road surface.

REMOVAL

SPRING STOP PLATESREMOVAL(1) Raise and support the vehicle. (2) Remove the tire and wheel assembly. (3) Remove the lower end of the stabilizer link from the stop plate. (4) Remove the three bolts retaining the spring stop plate from the lower control arm.

(1) Raise and support the vehicle. (2) Remove the stabilizer bar clamp bolts at the front axle (Fig. 11). (3) Press the rubber mount outwards out of the brackets (Fig. 11). (4) Remove the stabilizer links from the stabilizer bar (Fig. 11).

INSTALLATION(1) Install the spring stop plate to the lower control arm. Tighten the bolts to 60 Nm (44 ft. lbs.). (2) Install the stabilizer link to the spring stop plate. (3) Install the tire and wheel assembly. (4) Lower the vehicle.

STABILIZER BARDESCRIPTIONThe bar extends across the front underside of the chassis and connects to the frame crossmember. The ends of the bar mount to the lower suspension arm. All mounting points of the stabilizer bar are isolated by bushings (Fig. 10).

Fig. 11 STABILIZER BAR1 2 3 4 5 6 7 RUBBER MOUNT STABILIZER LINK RUBBER MOUNT NUT RUBBER MOUNT CLAMP BRACKET BOLT

INSTALLATION(1) Install the stabilizer links to the stabilizer bar (Fig. 11). (2) Install the stabilizer to the front axle (Fig. 11).

2 - 10

FRONT

VA

(3) Install the stabilizer bar clamp and bolts (Fig. 11). Tighten the bolts to 30 Nm (22 ft. lbs.). (4) Lower the vehicle.

STABILIZER LINKREMOVAL(1) Raise and support the vehicle. (2) Insert a pry bar between the stabilizer link and something solid to pry on. (3) Pry the stabilizer link off the stabilizer bar and the spring stop plate.

INSTALLATION(1) Install a mild detergent soap the to rubber bushings on the stabilizer link. (2) Install the stabilizer links onto the stabilizer bar and spring stop plate by pushing on the link. (3) Lower the vehicle.

Fig. 12 STRUT1 2 3 4 5 6 COVER NUT RUBBER MOUNT STRUT STRUT BOLT LOCKING BOLT

STRUTREMOVAL(1) On the drivers side remove the floor covering off to the side. (2) On the passengers side take off the cover for the tools. (3) Remove the cover for the upper strut mounting (Fig. 12). (4) Remove the nut on the upper strut mounting (Fig. 12). (5) Raise and support the vehicle. (6) Remove the front wheels. (7) Raise the lower control arm approximately 10 mm with a jack to remove the tension from the strut. (8) Remove the strut from the steering knuckle (Fig. 12).

INSTALLATIONNOTE: Hand tighten the strut upper mounting nut until the vehicle is on the ground, otherwise the bushings may become distorted. (1) Install strut to the steering knuckle (Fig. 12). Tighten to 185 Nm (136 ft. lbs.). (2) Raise the lower control to install the upper part of the strut into the footwell. Tighten to 100 Nm (74 ft. lbs.). (3) Install wheels (Refer to 22 - TIRES/WHEELS/ WHEELS - INSTALLATION). (4) Lower the vehicle. (5) Install the nut covers (Fig. 12). (6) Refit the floor covering and the tool cover.

VA

REAR

2 - 11

REARTABLE OF CONTENTSpage REAR DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 11 DIAGNOSIS AND TESTING - SPRING AND SHOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SPECIFICATIONS - TORQUE CHART . . . . . . 12 SHOCK DIAGNOSIS AND TESTING - SHOCK . . . . . . 13 REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 13 SPRING DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 14 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 14 REMOVAL REMOVAL - (SRW) . . . . . . . . . . . . . . . . . . . 14 REMOVAL - (DRW) . INSTALLATION INSTALLATION - (SRW) INSTALLATION - (DRW) SPRING SHACKLE REMOVAL ......... INSTALLATION ..... STABILIZER BAR REMOVAL ......... INSTALLATION ..... STABILIZER LINK REMOVAL ......... INSTALLATION ..... page . . . . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . . . 16 . . . . . . . . . . . . . . . . . . 16

REARDESCRIPTIONThe rear suspension is comprised of: Shock Absorbers Jounce Bumpers Stabilizer Bar Leaf Springs Drive Axle CAUTION: A vehicle should always be loaded so the vehicle weight center-line is located immediately forward of the rear axle. Correct vehicle loading provides proper front tire-to-road contact. This results in maximum vehicle handling stability and safety. Incorrect vehicle weight distribution can cause excessive tire tread wear, spring fatigue or failure, and erratic steering. CAUTION: Suspension components with rubber/urethane bushings (except stabilizer bar) should be tightened with the vehicle at normal ride height. It is important to have the springs supporting the weight of the vehicle when the fasteners are torqued. If springs are not at their normal ride position, vehicle ride comfort could be affected and premature bushing wear may occur.

bushings and metal brackets or attaching components. These noises can usually be stopped by tightening the attaching nuts. If the noise persists, inspect for damaged and worn bushings, and attaching components. Repair as necessary if any of these conditions exist. A squeaking noise from the shock absorber may be caused by the hydraulic valving and may be intermittent. This condition is not repairable and the shock absorber must be replaced. The shock absorbers are not refillable or adjustable. If a malfunction occurs, the shock absorber must be replaced. To test a shock absorber, hold it in an upright position and force the piston in and out of the cylinder four or five times. The action throughout each stroke should be smooth and even. The spring eye and shock absorber bushings do not require any type of lubrication. Do not attempt to stop spring bushing noise by lubricating them. Grease and mineral oil-base lubricants will deteriorate the bushing rubber. If the vehicle is used for severe, off-road operation, the springs should be examined periodically. Check for broken and shifted leafs, loose and missing clips, and broken center bolts. Refer to Spring and Shock Absorber Diagnosis chart for additional information.

DIAGNOSIS AND TESTING - SPRING AND SHOCKA knocking or rattling noise from a shock absorber may be caused by movement between mounting

2 - 12

REARSPRING AND SHOCK ABSORBERCONDITION POSSIBLE CAUSES 1. Broken leaf. 2. Spring fatigue. CORRECTION 1. Replace spring. 2. Replace spring. 1. Tighten to specification. 2. Replace bushings. 3. Replace spring tip inserts. 1. Tighten to specification. 2. Replace shock. 3. Replace shock.

VA

SPRING SAGS

SPRING NOISE

1. Loose spring clamp bolts. 2. Worn bushings. 3. Worn or missing spring tip inserts.

SHOCK NOISE

1. Loose mounting fastener. 2. Worn bushings. 3. Leaking shock.

SPECIFICATIONS - TORQUE CHARTTORQUE SPECIFICATIONSDESCRIPTION Sway Bar Link Sway Bar Clamp To Axle (SRW) Sway Bar Clamp To Axle (DRW) Rear Spring To Front Spring Bracket (SRW) Rear Spring To Front Spring Bracket (DRW) Rear Spring To Rear Spring Bracket (SRW) Rear Spring To Rear Spring Bracket (DRW) Spring Shackle To Rear Spring Bracket (SRW) Spring Shackle To Rear Spring Bracket (DRW) U-Bolt To Spring Plate & Axle (SRW&DRW) Lower Shock Mounting To Rear Axle M12 X 1.5 Bolt Nm 95 25 70 95 Ft. Lbs. 60 18 52 70 In. Lbs.

185

136

85

63

185

136

90

66

185

136

170

125

70

52

VADESCRIPTION Lower Shock Mounting To Rear Axle M14 X 1.5 Bolt (SRW&DRW) Upper Shock Mounting To Frame (SRW) Upper Shock Mounting To Frame (DRW) Nm 110 Ft. Lbs. 81

REARIn. Lbs.

2 - 13

80

59

140

103

SHOCKDIAGNOSIS AND TESTING - SHOCKA knocking or rattling noise from a shock absorber may be caused by movement between mounting bushings and metal brackets or attaching components. These noises can usually be stopped by tightening the attaching nuts. If the noise persists, inspect for damaged and worn bushings, and attaching components. Repair as necessary if any of these conditions exist. A squeaking noise from the shock absorber may be caused by the hydraulic valving and may be intermittent. This condition is not repairable and the shock absorber must be replaced. The shock absorbers are not refillable or adjustable. If a malfunction occurs, the shock absorber must be replaced. To test a shock absorber, hold it in an upright position and force the piston in and out of the cylinder four or five times. The action throughout each stroke should be smooth and even. The shock absorber bushings do not require any type of lubrication. Do not attempt to stop bushing noise by lubricating them. Grease and mineral oilbase lubricants will deteriorate the bushing.

Fig. 1 SHOCK ABSORBER (LEFT SIDE SHOWN)1 - CLIP 2 - WASHER 3 - MOUNTING STUD/BOLT 4 - WASHER 5 - NUT 6 - FRAME 7 - SHOCK ABSORBER 8 - BOLT 9 - NUT 10 - ALB LEVER

INSTALLATION(1) Install the shock absorber (Fig. 1). (2) Install the shock absorber bolt to the frame side (Fig. 1) Tighten to 80 Nm (59 ft.lbs.) for (SRW) or Tighten to 140 Nm (103 ft.lbs.) for (DRW). (3) Install the ALB lever to the upper shock bolt/ stud (left hand side only) (Fig. 1). (4) Snap the clip for the ALB lever (Fig. 1). (5) Install the shock absorber bolt to the rear axle (Fig. 1) Tighten to 70 Nm (52 ft.lbs.) for (M12X1.5 bolt) or Tighten to 110 Nm (81 ft.lbs.) for (M14X1.5 bolt). (6) Lower the vehicle.

REMOVAL(1) Raise and support the vehicle. (2) Remove the shock absorber bolt from the rear axle (Fig. 1). (3) Unsnap the clip for the ALB lever (left hand side) (Fig. 1). (4) Remove the ALB lever from the upper shock bolt/stud (Fig. 1). (5) Remove the shock absorber bolt from the frame side (Fig. 1). (6) Remove the shock absorber (Fig. 1).

2 - 14

REAR

VA

SPRINGDESCRIPTIONThe rear suspension system uses a multi-leaf springs and a solid drive axle. The forward end of the springs are mounted to the body rail hangers through rubber bushings. The rearward end of the springs are attached to the body by the use of shackles. The spring and shackles use rubber bushings.

REMOVAL - (DRW)(1) Raise and support the vehicle. (2) Support the rear axle. (3) Remove the U-bolt and spring plate (Fig. 3). (4) Remove the spring from the front spring bracket (Fig. 3). (5) Remove the rear spring with the spring shackle from the spring bracket (Fig. 3). (6) Lower the rear axle and remove the rear spring. (7) Remove the spring shackle from the spring (if needed) (Fig. 3).

OPERATIONThe springs control ride quality and maintain vehicle ride height. The shackles allow the springs to change their length as the vehicle moves over various road conditions.

REMOVAL REMOVAL - (SRW)(1) Raise and support the vehicle. (2) Support the rear axle. (3) Remove the U-bolt and spring plate (Fig. 2). (4) Remove the spring from the front spring bracket (Fig. 2). (5) Remove the rear spring with the spring shackle from the spring bracket (Fig. 2). (6) Lower the rear axle and remove the rear spring. (7) Remove the spring shackle from the spring (if needed) (Fig. 2).

Fig. 3 REAR LEAF SPRING WITH DUAL REAR WHEELS1 2 3 4 5 6 7 U-BOLTS NUT BOLT SPRING SHACKLE U-BOLT MOUNTING NUT U-BOLT BRACKET ALIGNING PLATE LEAF SPRING

INSTALLATION INSTALLATION - (SRW)NOTE: Larger spring bushing goes toward the front. (1) Install the spring shackle to the spring (if removed) (Fig. 2). Tighten to 90 Nm (66 ft. lbs.). (2) Install the spring to the front spring bracket (Fig. 2). Tighten to 95 Nm (70 ft. lbs.). (3) Install the spring to the rear spring bracket (Fig. 2). Tighten to 85 Nm (63 ft. lbs.). (4) Raise the rear axle and attach the spring plate and U-bolts (Fig. 2). Tighten to 170 Nm (125 ft. lbs.). (5) Lower the vehicle.

Fig. 2 REAR LEAF SPRING WITH SINGLE REAR WHEELS1 2 3 4 5 6 7 8 NUT LEAF SPRING U-BOLTS PLATE SPRING BOLT SHACKLE BOLT SPRING SHACKLE U-BOLT NUTS

VA

REAR

2 - 15

INSTALLATION - (DRW)NOTE: Larger spring bushing goes toward the front. (1) Install the spring shackle to the spring (if removed) (Fig. 3). Tighten to 185 Nm (136 ft. lbs.). (2) Install the spring to the front spring bracket (Fig. 3). Tighten to 185 Nm (136 ft. lbs.). (3) Install the spring to the rear spring bracket (Fig. 3). Tighten to 185 Nm (136 ft. lbs.). (4) Raise the rear axle and attach the spring plate and U-bolts (Fig. 3). Tighten to 170 Nm (125 ft. lbs.). (5) Lower the vehicle.

SPRING SHACKLEREMOVAL(1) Raise and support the vehicle. (2) Support the rear axle. (3) Remove both the rear spring shackles from the spring bracket. (4) Lower the rear axle and remove the rear spring shackle from the spring.

Fig. 4 SWAY BAR WITH SINGLE REAR WHEELS (SRW)1 - M12 NUT 2 - BUSHING 3 - SWAY BAR LINK 4 - M12 BOLT 5 - SWAY BAR 6 - CLAMP 7 - M8 BOLT 8 - BRACKET 9 - FOUR POINT NUT M8 10 - WASHER 11 - M8 NUT 12 - BUSHING 13 - MOUNT

INSTALLATION(1) Install the spring shackle to the spring. Tighten to 90 Nm (66 ft. lbs.). (2) Raise the rear axle while installing the spring shackle to the spring bracket. Tighten to 85 Nm (63 ft. lbs.). (3) Lower the vehicle.

INSTALLATION(1) Install the stabilizer bar to the axle. (2) Install the stabilizer bar clamps and bracket, center the bar then tighten to 25 Nm (18ft. lbs.) (SRW) (Fig. 4) or Tighten to 70 Nm (52 ft. lbs.) for (DRW) (Fig. 5). (3) Install the stabilizer bar to the stabilizer links and tighten to 95 Nm (60 ft. lbs.) (Fig. 4) or (Fig. 5). (4) Lower the vehicle.

STABILIZER BARREMOVAL(1) (2) (3) (Fig. (4) (5) Raise and support the vehicle. Remove the stabilizer links at the bar (Fig. 4). Remove the stabilizer bar clamp at the axle 4). Remove the bracket (Fig. 4) Remove the stabilizer bar from the vehicle.

2 - 16

REAR

VA

Fig. 5 SWAY BAR WITH DUAL REAR WHEELS (DRW)1 2 3 4 5 6 7 STABILIZER LINK SWAY BRA BOLT SWAY BAR NUT SWAY BAR RUBBER MOUNT SWAY BAR CLAMP CLAMP MOUNTING BOLTS

STABILIZER LINKREMOVAL(1) Raise and support the vehicle. (2) Remove the stabilizer links at the bar (Fig. 4). (3) Remove the stabilizer link at the frame.

INSTALLATION(1) Install the stabilizer bar to the stabilizer links and tighten to 95 Nm (60 ft. lbs.) (Fig. 4). (2) Lower the vehicle. (3) Install the stabilizer link to the frame. Tighten to 95 Nm (60 ft. lbs.).

VA

WHEEL ALIGNMENT

2 - 17

WHEEL ALIGNMENTTABLE OF CONTENTSpage WHEEL ALIGNMENT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 17 DIAGNOSIS AND TESTING - PRE-ALIGNMENT INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . 17 page STANDARD PROCEDURE - TOE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . 18 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . 19

WHEEL ALIGNMENTDESCRIPTIONNOTE: Camber and Caster are not adjustable on this vehicle. (TOE ONLY). NOTE: Suspension components with rubber/urethane bushings should be tightened with the vehicle at normal ride height. It is important to have the springs supporting the weight of the vehicle when the fasteners are torqued. If springs are not at their normal ride position, vehicle ride comfort could be affected and premature bushing wear may occur. Wheel alignment involves the correct positioning of the wheels in relation to the vehicle. The positioning is accomplished through suspension and steering linkage adjustments. An alignment is considered essential for efficient steering, good directional stability and to minimize tire wear. The most important measurements of an alignment are caster, camber and toe (Fig. 1). CAUTION: Never attempt to modify suspension or steering components by heating or bending.

Fig. 1 Wheel Alignment Measurements1 2 3 4 FRONT OF VEHICLE STEERING AXIS INCLINATION PIVOT POINT TOE-IN

DIAGNOSIS AND TESTING - PRE - ALIGNMENT INSPECTIONBefore starting wheel alignment, the following inspection and necessary corrections must be completed. Refer to Suspension and Steering System Diagnosis Chart below for additional information. (1) Inspect tires for size, air pressure and tread wear. (2) Inspect front wheel bearings for wear. (3) Inspect front wheels for excessive radial or lateral runout and balance. (4) Inspect ball studs, linkage pivot points and steering gear for looseness, roughness or binding. (5) Inspect suspension components for wear and noise. (6) Road test the vehicle.

2 - 18

WHEEL ALIGNMENTSUSPENSION AND STEERING SYSTEM DIAGNOSISCONDITION POSSIBLE CAUSES 1. Loose or worn wheel bearing. 2. Loose or worn steering or suspension components. 3. Loose or worn steering or suspension components. CORRECTION 1. Replace wheel bearing.

VA

FRONT END NOISE

2. Tighten or replace components as necessary. 3. Tighten or replace components as necessary. 1. Replace wheel bearing. 2. Tighten or replace components as necessary. 3. Replace steering gear. 1. Replace wheel bearing. 2. Tighten or replace components as necessary. 3. Replace or balance tires. 4. Align vehicle to specifications. 1. Replace wheel bearing. 2. Tighten or replace components as necessary. 3. Adjust tire pressure. 4. Align vehicle to specifications. 1. Replace steering gear. 2. Replace coupler. 3. Adjust tire pressure. 4. Align vehicle to specifications. 1. Adjust tire pressure. 2. Criss-Cross Front Tires. 3. Align vehicle to specifications. 4. Tighten or replace components as necessary. 5. Rotate or replace tire as necessary. 6. Repair brake as necessary. 7. Replace spring.

EXCESSIVE PLAY IN STEERING

1. Loose or worn wheel bearing. 2. Loose or worn steering or suspension components. 3. Loose or worn steering gear.

FRONT WHEELS SHIMMY

1. Loose or worn wheel bearing. 2. Loose or worn steering or suspension components. 3. Tires worn or out of balance. 4. Alignment.

VEHICLE INSTABILITY

1. Loose or worn wheel bearing. 2. Loose or worn steering or suspension components. 3. Tire pressure. 4. Alignment.

EXCESSIVE STEERING EFFORT

1. Loose or worn steering gear. 2. Column coupler binding. 3. Tire pressure. 4. Alignment.

VEHICLE PULLS TO ONE SIDE

1. Tire pressure. 2. Tire. 3. Alignment. 4. Loose or worn steering or suspension components. 5. Radial tire lead. 6. Brake pull. 7. Weak or broken spring.

STANDARD PROCEDURE - TOE ADJUSTMENTCAMBER AND CASTER ARE NOT ADJUSTABLE (TOE ONLY).. The wheel toe position adjustment is the final adjustment. (1) Start the engine and turn wheels both ways before straightening the wheels. Secure the steering wheel with the front wheels in the straight-ahead position.

(2) Loosen the tie rod jam nuts. NOTE: Each front wheel should be adjusted for one-half of the total toe position specification. This will ensure the steering wheel will be centered when the wheels are positioned straight-ahead. (3) Adjust the wheel toe position by turning the inner tie rod as necessary.

VA(4) Tighten the tie rod jam nut to 50 Nm (37 ft. lbs.). (5) Verify the specifications (6) Turn off engine.

WHEEL ALIGNMENTREAR SPECIFICATIONSDESCRIPTION Toe-In Max Camber Max Inclination of Rear Wheels (Individual Wheel Toe)= Maximum Inclination of Rear Axle Max

2 - 19

REAR SPECIFICATION 0 (0.25) 0 (-0.66/+0.33) 0 (0.25)

SPECIFICATIONSFRONT SPECIFICATIONSDESCRIPTION Toe-In Camber Camber Left to Right Difference Max Caster Steering Knuckle Inclination Steering Knuckle Inclination Left to Right Difference Max FRONT SPECIFICATION 0 (0.16) 0 (0.75) 1.33

0 (0.5) 0 (0.5) 1

TORQUE SPECIFICATIONSDESCRIPTION Outer Tie Rod End Jam Nut Nm 50 Ft. Lbs. 37 In. Lbs. -

VA

DIFFERENTIAL & DRIVELINE

3-1

DIFFERENTIAL & DRIVELINETABLE OF CONTENTSpage PROPELLER SHAFT .......................1 page REAR AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PROPELLER SHAFTTABLE OF CONTENTSpage PROPELLER SHAFT DIAGNOSIS AND TESTING PROPELLER SHAFT . . STANDARD PROCEDURE SPECIFICATIONS . . . . . . SPECIAL TOOLS ...... page PROPELLER SHAFT REMOVAL .............................7 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 9 CENTER BEARING REMOVAL .............................9 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 10

.. . .. ..

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

.1 .4 .6 .6

PROPELLER SHAFTDIAGNOSIS AND TESTING PROPELLER SHAFTPROPELLER SHAFT VIBRATIONOut-of-round tires or wheels that are out of balance, will cause a low frequency vibration. Driveline vibration can be from loose or damaged engine mounts. Propeller shaft vibration increases with vehicle speed. A vibration within a specific speed is not usually caused by a out of balanced propeller shaft. Worn universal joints or an incorrect propeller shaft angle, usually cause such a vibration.

3-2

PROPELLER SHAFTDRIVELINE VIBRATIONDrive Condition Possible Cause 1) Undercoating or other foreign material on shaft. 2) Loose U-joint clamp screws. 3) Loose or bent U-joint yoke or excessive runout. 4) Incorrect driveline angularity. 5) Rear spring center bolt not in seat. 6) Worn U-joint bearings. 7) Propeller shaft damaged or out of balance. 8) Broken rear spring. 9) Excessive runout or unbalanced condition. 10) Excessive drive pinion gear shaft runout. 11) Excessive axle yoke deflection. 12) Excessive transfer case runout. Correction

VA

Propeller Shaft Noise

1) Clean exterior of shaft and wash with solvent. 2) Install new clamps and screws and tighten to proper torque. 3) Install new yoke. 4) Measure and correct driveline angles. 5) Loosen spring u-bolts and seat center bolt. 6) Install new U-joint. 7) Installl new propeller shaft. 8) Install new rear spring. 9) Re-index propeller shaft, test, and evaluate. 10) Re-index propeller shaft and evaluate. 11) Inspect and replace yoke if necessary. 12) Inspect and repair as necessary. 1) Install new clamps and screws and tighten to proper torque. 2) Replace as U-joints as necessary.

Universal Joint Noise

1) Loose U-joint clamp screws. 2) Lack of lubrication.

PROPELLER SHAFT BALANCENOTE: Removing and indexing the propeller shaft 180 relative to the yoke may eliminate some vibrations. If propeller shaft is suspected of being out of balance, verify with the following procedure: (1) Place vehicle in netrual. (2) Raise and support the vehicle by the axles as level as possible. (3) Clean all foreign material from propeller shaft and universal joints. (4) Inspect propeller shaft for missing balance weights, broken welds, and bent areas. NOTE: If propeller shaft is bent, it must be replaced. (5) Inspect universal joints for wear, properly installed and correct alignment with the shaft. (6) Check universal joint clamp screws torque. (7) Remove wheels and tires. Install wheel lug nuts to retain the brake drums/rotors.

(8) Mark and number propeller shaft six inches from the pinion yoke end at four positions 90 apart. (9) Run and accelerate the vehicle until vibration occurs. Note intensity and speed the vibration occurred. Stop the engine. (10) Install a screw clamp at position 1 (Fig. 1).

VA

PROPELLER SHAFT

3-3

Fig. 1 Clamp Screw At Position 11 - CLAMP 2 - SCREWDRIVER 1 - 12 INCH

Fig. 3 Clamp Screws Separated(14) Increase distance between clamps and repeat test until vibration is at the lowest level. Bend the slack end of the clamps so the screws will not loosen. (15) If vibration remains unacceptable, preform the procedure to the front end of the propeller shaft. (16) Install the wheel and tires. Lower the vehicle.

(11) Start engine and re-check for vibration. If little or no change in vibration is evident, move clamp to the next positions and repeat vibration test. NOTE: If there is no difference in vibration at the other positions, the vibration may not be propeller shaft. (12) If vibration decreased, install a second clamp (Fig. 2) and repeat vibration test.

PROPELLER SHAFT RUNOUT(1) Clean the propeller shaft surface where the dial indicator will contact the shaft. (2) The dial indicator must be installed perpendicular to the shaft surface. (3) Measure runout at the center and ends of the shaft away from weld areas, to ensure weld process will not effect the measurements. (4) Refer to Runout Specifications chart. (5) If propeller shaft is out of specification, remove propeller shaft and index the shaft 180. Install the propeller shaft and measure shaft runout again. (6) If propeller shaft is now within specifications, mark shaft and yokes for proper orientation. (7) If propeller shaft runout is not within specifications, check runout of the transmission and axle. Correct as necessary and repeat propeller shaft runout measurement. (8) Replace propeller shaft if the runout still exceeds the limits.

Fig. 2 Two Clamp Screws At The Same Position(13) If additional clamp causes additional vibration, separate clamps 1/2 inch above and below the mark. Repeat the vibration test (Fig. 3).

3-4

PROPELLER SHAFTRUNOUT SPECIFICATIONS

VARULES Good cancellation of U-joint operating angles should be within 1degree. Operating angles should be less than 3 degrees. At least 1/2 of one degree continuous operating (propeller shaft) angle.

Front of Shaft Center of Shaft Rear of Shaft

0.020 in. (0.50 mm) 0.025 in. (0.63 mm) 0.020 in. (0.50 mm)

note: Measure front/rear runout approximately 76 mm (3 in.) from the weld seam at each end of the shaft tube for tube lengths over 30 inches. For tube lengths under 30 inches, the maximum allowed runout is 0.50 mm (0.020 in.) for the full length of the tube.

STANDARD PROCEDUREPROPELLER SHAFT ANGLEThis procedure applies the front and rear propeller shafts. (1) Place vehicle in netural. (2) Raise and support vehicle at the axles as level as possible. (3) Remove universal joint snap rings if equipped, so Inclinometer 7663 base sits flat. (4) Rotate shaft until transmission case output yoke bearing is facing downward. NOTE: Always make measurements from front to rear and from the same side of the vehicle. (5) Place Inclinometer 7663 on yoke bearing (A) parallel to the shaft. Center bubble in sight glass and record measurement. This measurement will give you the transmission yoke Output Angle (A). (6) Rotate propeller shaft 90 degrees and place inclinometer on yoke bearing parallel to the shaft. Center bubble in sight glass and record measurement. This measurement can also be taken at the rear end of the shaft. This measurement will give you the Propeller Shaft Angle (C). (7) Rotate propeller shaft 90 degrees and place inclinometer on companion flange yoke bearing parallel to the shaft. Center bubble in sight glass and record measurement. This measurement will give you the Pinion Flange Input Angle (B). (8) Subtract smaller figure from larger (C minus A) to obtain Transmission Output Operating Angle. (9) Subtract smaller figure from larger (C minus B) to obtain axle Input Operating Angle. Refer to rules and example in (Fig. 4) for additional information.

VA

PROPELLER SHAFT

3-5

Fig. 4 UNIVERSAL JOINT ANGLE EXAMPLE1 - 4.9 Angle (C) 2 - 3.2 Angle (B) 3 - Input Yoke 4 - 3.0 Angle (A) 5 - Output Yoke

TWO / THREE - PIECE PROPELLER SHAFTThe procedure to measure the propeller shaft angles involved with a two/three-piece (Fig. 5) propeller shaft is the same as those for a one-piece propeller shaft.

3-6

PROPELLER SHAFT

VA

Fig. 5 UNIVERSAL JOINT ANGLE1 - YOKES MUST BE IN SAME PLANE

SPECIFICATIONSTORQUE SPECIFICATIONSDESCRIPTION Propeller shaft to transmission bolt Propeller shaft to axle bolt Retaining bracket to frame floor bolt Center Bearing support to frame floor bolt Center Bearing to support nut Nm 70 70 100 95 105 Ft. Lbs. 52 52 74 70 77 In. Lbs. -

SPECIAL TOOLSSPECIAL TOOL CROSS-REFERENCE CHARTMB TOOL # N/A N/A 387 589 05 15 00 N/A MILLER TOOL # 938 1130 9275 7663 DESCRIPTION BRIGE SPLITTER INSTALLER INCLINOMETER

BRIDGE 938

VA

PROPELLER SHAFT

3-7

SPLITTER 1130

Fig. 6 ALIGNMENT MARKS1 2 3 4 ALIGNMENT MARK BOOT ALIGNMENT MARK CENTER BEARING

INSTALLER 9275

INCLINOMETER 7663

PROPELLER SHAFTREMOVAL(1) Secure vehicle to prevent it from rolling. (2) Make installing reference marks on propeller shaft (Fig. 6) and (Fig. 7).1 2 3 4 -

Fig. 7 ALIGNMENT MARKS 3 PIECE SHAFTREFERNCE MARK CENTER SHAFT REFERENCE MARK REAR SHAFT

(3) Remove retaining bracket bolts (Fig. 8) and (Fig. 9). (4) Remove propeller shaft bolts from rear axle and transmission at the flange. (5) Remove propeller shaft intermediate bearing nuts from retaining bracket and bracket for brake cable. NOTE: The brake cable bracket is only installed in vehicles with wheelbase 3550 mm

3-8

PROPELLER SHAFT

VA

Fig. 8 2 PIECE PROPELLER SHAFT1 2 3 4 5 FLANGE BOLT BEARING PROPELLER SHAFT REAR AXLE CABLE BRACKET 6 - NUT 7 - BRACKET 8 - RETAINING BRACKET 9 - COLLARED BOLT 10 - TRANSMISSION

VA

PROPELLER SHAFT

3-9

Fig. 9 3 PIECE PROPELLER SHAFT1 2 3 4 5 6 FLANGE BOLT INTERMEDIATE BEARING CENTER SHAFT REAR SHAFT REAR AXLE NUT 7 - BRACKET 8 - RETAINING BRACKET 9 - BOLT 10 - FRONT SHAFT 11 - TRANSMISSION

(6) Remove shaft from the vehicle.

INSTALLATION(1) Install propeller shaft intermediate bearing/ bearings to support and tighten nuts to 105 Nm (77 ft. lbs.). (2) Install propeller shaft intermediate bearing support/supports to frame floor and tighten bolts to 95 Nm (70 ft. lbs.). (3) Install propeller shaft intermediate bearing with retaining bracket and bracket for brake cable. NOTE: The bracket is only installed on vehicles with wheelbase 3550 mm. (4) Install propeller shaft to rear axle and transmission flange with installation marks are aligned. Tighten bolts to 70 Nm (66 ft. lbs.). (5) Install retaining bracket and tighten bolts to 100 Nm (74 ft. lbs.).

Fig. 10 ALIGNMENT MARKS1 2 3 4 ALIGNMENT MARK BOOT ALIGNMENT MARK CENTER BEARING

CENTER BEARINGREMOVAL(1) Remove propeller shaft. (2) Mark shafts for installation alignment (Fig. 10).

(3) Loosen both collar clamps (Fig. 11).

3 - 10

PROPELLER SHAFT

VA

Fig. 11 BOOT1 - BOOT 2 - CLAMP 3 - SHAFT

(4) Pull apart propeller shaft. (5) Remove snap-ring (Fig. 12).1 2 3 4 -

Fig. 13 CENTER BEARING REMOVALBRIDGE PLUG BEARING SPLITTER CENTER BEARING

INSTALLATION(1) Press center bearing on propeller shaft with protective caps and washer with Installer 9275 (Fig. 14).

Fig. 12 CENTER BEARING1 2 3 4 5 SNAP-RING CENTER BEARING WASHER SHAFT PROTECTIVE CAP

NOTE: If center bearing is equipped with a round flange remove bolt from the middle of the flange. (6) Pull off center bearing with a Bearing Splitter 1130 and Bridge 938, with a plug on the end of the shaft (Fig. 13). NOTE: The bearing splitter must be positioned behind the thrust washer of the bearing.

Fig. 14 CENTER BEARING INSTALLATION1 - INSTALLER 2 - CENTER BEARING

VANOTE: If center bearing is equipped with a round flange install new bolt in middle of the flange and tighten to 95 Nm (70 ft. bls.). (2) Install snap-ring. (3) Coat propeller shaft spline with universal grease. (4) Push rubber boot onto propeller shaft. (5) Push together propeller shaft. Pay attention to alignment markings for installation position. (6) Ensure rubber seal is correctly installed and attach new collar clamps. (7) Install propeller shaft.

PROPELLER SHAFT

3 - 11

3 - 12

REAR AXLE

VA

REAR AXLETABLE OF CONTENTSpage REAR AXLE DIAGNOSIS AND TESTING . . . . . . . . . . . . . STANDARD PROCEDURE - DRAIN AND FILL REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . SPECIAL TOOLS .................... SHAFT-AXLE SINGLE REAR WHEEL REMOVAL-SINGLE REAR WHEEL . . . . . . . INSTALLATION-SINGLE REAR WHEEL . . . . BEARING/SEAL-AXLE REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . SHAFT-AXLE DUAL REAR WHEELS REMOVAL-DUAL REAR WHEEL . . . . . . . . . INSTALLATION-DUAL REAR WHEEL ..... BEARING/SEAL-AXLE HUB REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . . . . DIFFERENTIAL REMOVAL . . . . . . . . . . . . . . . . . . . . . . . DISASSEMBLY DISASSEMBLY-SINGLE REAR WHEEL DISASSEMBLY-DUAL REAR WHEEL . ASSEMBLY ASSEMBLY-SINGLE REAR WHEEL . . ASSEMBLY-DUAL REAR WHEEL . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . BEARINGS-DIFFERENTIAL CASE REMOVAL . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . SEAL-PINION REMOVAL . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . GEAR-PINION/RING REMOVAL . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION . . . . . . . . . . . . . . . . . . . page

.. . .. .. .. ..

. 12 . 13 . 14 . 16 . 18 . 19

. . . . . . 31 . . . . . 32 . . . . . . 33 . . . . . . 34 . . . . . . 36 . . . . . . 37 . . . . . . 38 . . . . . . 38 . . . . . . 39 . . . . . . 40 . . . . . . 41 . . . . . . 42

. . . 23 . . . 24 . . . 24 . . . 26 . . . 27 . . . 28 . . . 28 . . . 29

REAR AXLEDIAGNOSIS AND TESTINGNOTE: Axle seals, axle bearings, pinion seals and differential cover are the only serviceble components. If differential is damaged/noisy the axle must be replaced.

noise during straight-ahead driving when the gears are unloaded. The side gears are loaded during vehicle turns. A worn pinion shaft can also cause a snapping or a knocking noise.

BEARING NOISEThe axle shaft, differential and pinion bearings can all produce noise when worn or damaged. Bearing noise can be either a whining, or a growling s