Higher Precision Longer LifeManualLathesEuropean TUR630-710MTRI-V Lathes

Features25• ” or 28” swing over bed x 78”, 118” or 157” bc20 HP main drive, 21 speeds• BIG 4.1• ” or 5.5” spindle bores with speeds up to 1800 RPM17• ” wide TRI-V bed designFully clutched headstock•Automatic positioning leadscrew and feed shaft supports•Heavy duty tailstock with 4• ” diameter quill and come-along Easy operator’s controls, 4-way rapids, Americanized electronics• Top European quality and design•Higher precision spindle•5.5” bore oil country version with rear nose for • “dual” chucks1-88 TPI available•Feed reversal at apron•Wide range of options including toolpost, chip conveyor, •taper attachment, chucks, steadies, VS, etc.

www.toolmex.com

5.5” spindle bore, D11 series, and TRI-V bedways

Convenient operator controls at carriage with 4-way rapids

TUR630-710S/A European Built Manual Lathes

2015 S. Mitchell Blvd., Schaumburg, IL 60193+1-847-301-3700 • 800-992-4766 • Fax +1-847-301-3703www.toolmex.com

Distributed by

4-999-7006 2-12 2.0

©2012 Toolmex Industrial Solutions. All rights reserved. All specifications on this sheet are subject to change without notice. Photos shown are a general representation of the various models and may include some optional equipment. Toolmex Industrial Solutions, Elektrim, and Elektrimax are trademarks of Toolmex Corporation, Inc.

Scan and Explore

American manual quick change toolpost with T-slot compound

Capacity / Model 25"TUR630S

25"TUR630A

28"TUR710S/A

Swing Over Bed 24.8" 24.8" 28"Swing Over Cross Slide 14.9" 14.9" 17.3"Distance Between Centers 78", 118", 157" 78", 118", 157" 118"

Headstock

Spindle Bore (Option) 4.1" 5.5" 4.1" (5.5)Spindle Nose (Option) D1-8 Dual D1-11 D1-8 (Dual D1-11)Spindle Speeds (24 Speeds) 18-1800 RPM (21 Speeds) 15-1400 RPM (24 Speeds) 14-1400 RPMSpindle Bearings Front - Angular Contact Ball Bearings (SKF), 8.2" O.D.

Feeds & Threads

42 Longitudinal Feeds .002-.121 IPR .002-.121 IPR .002-.121 IPR42 Cross Feeds .001-.060 IPR .001-.060 IPR .001-.060 IPR42 Inch Threads 1-88 TPI 1-88 TPI 1-88 TPI42 Metric Threads 1-88 mm/rev 1-88 mm/rev 1-88 mm/revLeadscrew Diameter 1.6" (4 TPI) 1.6" (4 TPI) 1.6" (4 TPI)

Carriage

Cross Slide Travel 13" 13" 15"Carriage Length Bearing on Ways 24" 24" 24"Cross Slide Width x Length 9" x 31" with Dual T-Slots for Rear FixturingSaddle Length Supporting Cross Slide 36" 36" 38.5"Top Slide Travel 6" 6" 6"4-Way Rapid Traverse (longitudinal/cross) 220 IPM / 110 IPM 220 IPM / 110 IPM 220 IPM / 110 IPM

Tailstock

Quill Diameter 3.9" 3.9" 3.9"Center, Morse Taper MT5 MT5 MT5Quill Travel 8" 8" 8"

General

Main Drive Motor 20 HP 20 HP 20 HPTRI-V Bed, width x depth 17" x 15.2" 17" x 15.2" 17" x 15.2"Number of Legs Supporting Bed (3) 78" bc , (4) 118" bc (3) 78" bc , (4) 118" bc (4) 118" bcMachine Weight, 118" bc 9,900 lbs. 10,200 lbs. 10,700 lbs.