If you can't read please download the document
Upload
romeomihaita
View
663
Download
12
Tags:
Embed Size (px)
DESCRIPTION
manual service canon ir 2545
Citation preview
9
99-38
9-38
System Upgrade RAM-C1 Installation Procedure
Checking the Contents
512MB RAM x1.
T-9-3
Points to Note Before Installation Turning Main Power OFF
CAUTION
Perform the following in the order prior to the installation.
1) Turn the main power of the host machine OFF.
2) Confirm the control panel display and the main power lamp have turned OFF and unplug the power cord.
9
99-39
9-39
Installation Procedure
1) Remove the rear cover (right). Screws (3 pcs.) Claws (2 pcs.)
Claws
x3
x2
F-9-86
2) Remove the controller plate. Screws (3 pcs.)
x3
F-9-87
3) Press the SW3 on the controller PCB and confirm LED10 has gone OFF. (This action is to cut the secondary power OFF.)
F-9-88
9
99-40
9-40
4) Release the 2 hooks to detach the 256MB RAM.
F-9-89
5) Insert the system upgrade memory in the slot where the 256MB RAM has been detached.
MEMO: Be sure the upgrade memory has firmly been inserted and the hooks are in the hole of the memory as shown.
F-9-90
9
99-41
9-41
6) Fix the controller plate with 3 screws (TP, M3x6).7) Fix the rear cover (right) with 3 screws (RS-tight, M3x8).8) Connect the power plug of the host machine to the power outlet and
turn its main power switch ON.
9) Checking the Connection
9-1) Have the service mode display by pressing the following keys in order: >2key>8key> In response, [#SSSW] appears.9-2) Use left or right cursor [< / >] key and press [OK] when [REPORT] has appeared.9-3) Use left or right cursor [< / >] key and press [OK] when [REPORT OUTPUT] has appeared.9-4) Use left or right cursor [< / >] key and press [OK] when [SPEC LIST] has appeared.9-5) SPEC REPORT is printed out. Confirm TOTAL MEMORY is [512MB] on the report.
9
99-42
9-42
System Upgrade SD CARD-A1Installation Procedure
Checking the Contents
[1] System Upgrade SD Card x 1
Points to Note before Installation
CAUTION:
Be sure that the eAM_License has been registered. Otherwise, the AM button may not be displayed on UI screen, and System does not become effective.
Turning OFF the Host MachineTurn OFF the main power switch on the host machine, and then remove the power plug from the outlet.
9
99-43
9-43
Installation Procedure
1) Remove the SD Cover.
1 Screw
F-9-91
2) Insert the System Upgrade SD Card.
T-9-4F-9-92
3) Return the SD Card Cover to its original position.
Checking after Installation1) Turn ON the main power.2) Check that the AM button is displayed.
MEMO:If the AM button is displayed, it means that eAM has been recognized. If there is operation failure with the System Upgrade SD Card, E602 will be displayed.
9
99-44
9-44
Cst Heater Kit-J1 Installation Procedure
Checking the Contents
[5]
[6]
[1] [2] [3]
[4]
[7]
Unpack the shipping carton and confirm the following components are contained in the carton.
[1] Heater PCB 1pc.[2] Heater SW harness 1pc.[3] Heater AC harness 1pc.[4] Heater DC harness 1pc.[5]*1 High temperature caution label 1pc.[6]*1 Cassette heater sheet 1pc.
[7] Screw (RS-tight, M3x8) 1pc.
*1:These items are used only when the cassette heater is to be installed in the iR2530/2525/2520 series model with its 1st cassette capacity is 250 sheets. Save them even if the cassette heater is not being installed.
F-9-93
Points to Note Before Installation Turning Main Power OFF
CAUTION
Perform the following in the order prior to the installation.
1) Turn the main power of the host machine OFF.
2) Confirm the control panel display and the main power lamp have turned OFF and unplug the power cord.
9
99-45
9-45
Installation Procedure
1) Remove the rear cover (right). Screws (3 pcs.) Claws (2 pcs.)
Claws
x3
x2
F-9-94
2) Cut off the blindfold cover of the rear cover (right) by a side cutter as shown.
CAUTION:
Finish the surface of the cut part of the rear cover (right) to remove burrs.
F-9-95
3) Remove the left rear blindfold cover. Screw (1 pc.)
F-9-96
4) Remove the left rear cover. Screws (3 pcs.)
x3
F-9-97
9
99-46
9-46
5) Remove the connector cover. Screw (1 pc.)
x1
F-9-98
6) Remove the rear lower cover. Screw (1 pc.) Craw (1 pc)
Claw
x1
x1
F-9-99
7) Remove the left cover and distort it to detach the inner bottom cover. Screw (1 pc.)
x1
F-9-100
9
99-47
9-47
8) Remove the left cover. Screw (1 pc.)
x1
Link Rod
CAUTION:There is the link rod behind the left cover, which is engaged to the switch on the power supply unit. So carefully remove the left cover not to give an excessive lord on the link rod.
F-9-101
MEMO: When reinstalling the left cover, surely insert the link rod in the switch on the power supply unit so the switch does link to the main power switch of the host machine.
x1 x2
F-9-102
9) Install the heater SW harness firmly in the power cord bracket.
MEMO:IInstall the heater SW harness in the correct direction referring to the figure in the power cord bracket.
F-9-103
9
99-48
9-48
10) Put the longer harness out of two through the hole of the rear frame.
F-9-104
11) Joint the connector of the longer harness of the heater SW harness to J108 of the power supply unit.
x1
F-9-105
12) Install the heater PCB. Screw (1 pc.)
x1
F-9-106
9
99-49
9-49
13) Unlock the wire saddles and stretch the folded harness as shown. Then joint the connector to the heater PCB.
x1x2
F-9-107
14) Joint the connector of the heater DC harness, which is closer to the protective tube of the harness to J1102 of the heater PCB.15) Clamp the 3 harnesses as shown in the figure.
x1
CAUTION:
Scatter the slack of the wire and comfirm which the do not touch the part of the primary circuit.
F-9-108
9
99-50
9-50
16) Clamp the harness in the 4 wire saddles.17) Joint the connector of the heater DC harness to J113B on the power supply unit.
x4
CAUTION:Scatter the slack of the wire and comfirm which the do not touch the part of the primary circuit.
F-9-109
18) Install the heater AC harness as shown in the figure. Joint the connector of the longest branch of the heater AC harness to the cassette junction bracket.
F-9-110
9
99-51
9-51
19) In case the cassette heater is not installed, disconnect the connector of the heater AC harness from the heater PCB and clamp it as shown in the figure.
x1
x1
x1
F-9-111
20) Restore the removed parts: Left cover (1 screw) Inner bottom cover (1 screw) Rear lower cover (1 screw) Connector cover (1 screw) Left rear cover (3 screws) Left rear blindfold cover (1 screw) Rear cover (right) (3 screws)
9
99-52
9-52
Reader Heater Unit-H1 Installation Procedure
Checking the Contents
[1]
[3]
[4] [5]
[2]
Confirm the following components with correct quantities are contained in the carton.
[1] Reader heater 2pcs. (FK2-0228)[2] Heater harness 1pc. (FM4-2929)[3] Wire saddle (large) 3pcs. (WT2-5719)[4] Wire saddle (small) 3pcs. (WT2-0507, only for use in iR-2545/2535)[5] Screw 2pcs. (XB2-8400-609)
Get the following service parts ready for installation.
[1] Reader heater 2pcs. (FK2-9468)[2] Heater harness 1pc. (FM4-2929)[3] Wire saddle (large) 3pcs. (WT2-5719)[4] Wire saddle (small) 3pcs. (WT2-0507, only for use in iR-2545/2535)[5] Screw 2pcs. (XB2-8400-609)
F-9-112
Points to Note Before Installation Turning Main Power OFF
CAUTION
Perform the following in the order prior to the installation.
1) Turn the main power of the host machine OFF.
2) Confirm the control panel display and the main power lamp have turned OFF and unplug the power cord.
Confirmation of Heater Driver PCBConfirm that the heater driver PCB has already been installed in the host machine.
9
99-53
9-53
Installation Procedure Installation of Reader Harness
1)Detach the rear cover (right). Screws (3 pcs.) Claws (2 pcs.)
Claws
x3
x2
F-9-113
2) Detach the rear cover (left). Screws (2 pcs.) Claws (2 pcs.)
x2
x2Claws
F-9-114
3) Detach the left rear blindfold cover. Screw (1 pc.)
F-9-115
4) Detach the left rear cover. Screws (3 pcs.)
x3
F-9-116
9
99-54
9-54
5) Detach the connector cover. Screw (1 pc.)
x1
F-9-117
6) Detach the rear lower cover. Screws (1 pc.) Claws (1 pc.)
Claw
x1
x1
F-9-118
7) Install the 3 supplied wire saddle (large) in the frame at rear left side.
F-9-119
9
99-55
9-55
8)Joint 1 connector of the heater harness to J1105 of the heater driver PCB.9)Put 2 connectors through each hole as shown in the figure and set the heater harness in the wire saddles.
x9
x2
J1105
F-9-120
[A]
F-9-121
[B]
F-9-122
[C]
CAUTION:
Pay attention not to give damages on the flexible cable.
F-9-123
9
99-56
9-56
Removal of Parts from Reader
1)Open the ADF (or platen Cover).2)Remove 2 screws to detach the glass retainer (right).3)Remove the platen glass.
x2
F-9-124
Installation of Reader Heater (for iR2530/2525/2520 series)
1)Move the drive belt in the arrow direction to shift the CIS to the center.2)Turn up the sheet.
F-9-125
3)Joint the 1 connector and install the heater (left) with 1 screw.
x1
x1
x1
F-9-126
9
99-57
9-57
4)Joint 1 connector and install the heater (right) with 1 screw.
x1
x1
x1
F-9-127
5)Restore the following parts:
Platen glassGlass retainer (right) 2 screwsRear lower cover 1 screwConnector cover 1 screwLeft rear cover 3 screwsLeft rear blindfold cover
1 screw
Rear cover (left) 3 screwsRear cover (right) 2 screws
6)Turn the switch of the heater power ON.
Installation of Reader Heater (for iR2545/2535 series)
1)Move the drive belt in the arrow direction to shift the D unit to the center.
F-9-128
2)Install the 2 supplied wire saddles (small).3)Joint 1 connector and install the heater (left) with 1 screw.
x2
x1
x1
F-9-129
9
99-58
9-58
4)Install the 1 supplied wire saddle (small), joint 1 connector and install the heater (right) with 1 screw.
x1
x1
x1
F-9-130
5)Restore the following parts:
Platen glassGlass retainer (right) 2 screwsRear lower cover 1 screwConnector cover 1 screwLeft rear cover 3 screwsLeft rear blindfold cover
1 screw
Rear cover (left) 3 screwsRear cover (right) 2 screws
6)Turn the switch of the heater power ON.
9
99-59
9-59
Cassette Heater Unit 37 Installation Procedure
Points to Note before Installation
CAUTION:
Check that the Heater PCB-J1 is installed. If not, install the Heater PCB-J1 before installing the Cassette Heater Unit.
The Cassette Heater Sheet and Warning High Temperature Label used for the 250-sheet Cassette Model is packed with the Heater PCB -J1.
Checking the Contents
[1] Cassette Heater Unit x 1
[5] Screw (P Tight; M3x8) x 1
[2] Heater Connector Cover x 1 [3] Wire Saddle x 1 [4] Screw( Sems Round End; M3X6) x 1
The 2-Cassette Unit does not use. F-9-131
9
99-60
9-60
Turning OFF the Host MachineTurn OFF the main power switch on the host machine, and then remove the power plug from the outlet.
Installation Procedure In case of 550 Sheets Cassette Model
1) Remove the cassette. 2) Remove the Connector cover. 1 Screw 4 Connectors
F-9-132
3) Remove the Lower rear cover.
1 Screw 1 Claw
Claw
F-9-133
9
99-61
9-61
4) Install the wire saddle to Heater Connector Cover.
F-9-134
5) Put the connector of the heater through the Wire Saddle and install the Heater Connector Cover.
1 Screw (P tight; M3x8) 1 Wire saddle
F-9-135
MEMO:If a screw is on the bottom of the Cassette Base, remove the screw. (The removed screw will not be used.)
F-9-136
9
99-62
9-62
6) Install the Cassette Heater Unit by fitting the3 hooks to the holes .At that time, put the connector through the square hole.
Cassette Heater Unit
Cassette Heater Unit
Base plate
F-9-137
7) Connect the Cassette Heater Unit with the stubby driver. 1 Screw (W sems round end; M3x6)
F-9-138
8) Connect the cassette heater connector to the heater relay cable connector.
F-9-139
9) Install the Lower rear cover10) Connect the 4 Connectors.11) Install the Connector Cover.12) Install the removed Cassettes.13) Check that the Environment
Heater switch is ON.14) Plug the power plug of the host
machine to the outlet.15) Turn ON the main power switch.
9
99-63
9-63
In case of 250 Sheets Cassette Model
1) Remove the cassette. 2) Remove the Connector Cover.
2 Screws 4 Connectors
x2 x4
F-9-140
F-9-141
3) Remove the Lower rear cover. 1 Screw 1 Claw
Claw
F-9-142
4) Remove the Rear cover (right). 3 Screws 2 Claws
Claws
x3
x2
F-9-143
9
99-64
9-64
5) Remove the Heater PCB.
4 Connectors J1101 connector (SW side). J1102 connector (PSV side). J1103 connector (E controller side). J1106 connector
(Cassette heater side).x4
F-9-144
1 Screw 1 Claw
F-9-145
6) Open the Front cover.7) Open the Toner supply cover.8) Open the Right cover.
9
99-65
9-65
9) Remove the support cover.
2 Screws
x2
F-9-146
10) Remove the screw on the lower left cover.
F-9-147
11) Remove the Inside base cover.
2 Bosses 2 Hooks 2 protrusions
Protrusion
Boss
Hook
F-9-148
12) Remove the delivery tray.
4 Bosses 1 Hook 1 Screw
Boss
Boss
Hook
F-9-149
9
99-66
9-66
13) Install the Wire Saddle to Heater Connector Cover.
F-9-150
14) Affix the Cassette Heater Sheet on the cassette heater, and put the connector of the heater and install the heater connector cover through the Wire Saddle.
1 Screw (P tight; M3x8) Cassette Heater Sheet
F-9-151F-9-152
MEMO:If a screw is on the bottom of the Cassette Base, put a long screwdriver through the hole on the plate and remove the screw. (The removed screw will not be used.)
F-9-153
9
99-67
9-67
15) Install the Cassette Heater Unit by fitting the3 hooks to the holes .At that time, put the connector through the square hole.
Cassette Heater Unit
Cassette Heater Unit
Base plate
F-9-154
16) After setting the cassette heater into the host machine, secure the heater in place with a long screwdriver by putting it through a hole on the plate. 1 Screw (W sems round end; M3x6)
F-9-155
9
99-68
9-68
17) Connect the connector at the heater side to the Heater Relay Harness.
F-9-156
18) Affix the Warning High Temperature Label to the specified area. (area between screw holes on the Base Plate)
CAUTION:
Label Warning high temp label use a label corresponding to the language.
Warning high temp label
F-9-157
19) Install the Heater PCB.20) Connect 4 connectors to the Heater PCB.21) Install the removed covers. Lower rear cover Connector cover Delivery tray Inside base cover Screw on Left cover Right cover (upper)22) Close the Right cover.23) Close the Toner supply cover.24) Close the Front cover.25) Install the removed Cassettes.26) Check that the Environment Heater switch is ON27) Plug the power plug of the host machine to the outlet.28) Turn ON the main power switch.
9
99-69
9-69
In case of 1-Cassette Unit
1) Remove the cassette. 2) Remove the Connector Cover.
2 Screw 4 Connectors
x2 x4
F-9-158F-9-159
3) Remove the Lower rear cover.
3 Screw
F-9-160
9
99-70
9-70
4) If equipped with the heater connector plate at rear side of the Cassette Module, remove it. (The removed heater connector plate will not be used.)
1 Screw
MEMO:When performing this procedure, it is not necessary to remove the Host Machine. However, the figure shows the picture with out the Host Machine to show easily.
F-9-161
5) Install the Wire Saddle to Heater Connector Cover.
F-9-162
6) Put the connector of the heater through the Wire Saddle and install the Heater Connector Cover.
1 Screw (P tight; M3x8) 1 Wire saddle
F-9-163
9
99-71
9-71
MEMO:If a screw is on the bottom of the Cassette Base, remove the screw. (The removed screw will not be used.)
F-9-164
7) Install the Cassette Heater Unit by fitting the3 hooks to the holes .At that time, put the connector through the square hole.
Cassette Heater Unit
Cassette Heater Unit
Base plate
F-9-165
8) Connect the cassette heater unit with the stubby driver. 1 Screw (W sems round end; M3x6)
F-9-166
9
99-72
9-72
9) AT the rear side of the Cassette Module, pull out the connector at the heater side and the connect the connecter.
MEMO:When performing this procedure, it is not necessary to remove the Host Machine. However, the figure shows the picture with out the Host Machine to show easily.
F-9-167
10) Disconnect the cable of the heater.
2 Wire saddles
x2
F-9-168
11) Put the cable of the heater through a hole of the plate.
F-9-169
12) Install the Lower rear cover.
9
99-73
9-73
13) Connect the connector of the heater to the 1-Cassette Pickup Unit.
F-9-170
14) Connect the 4 Connectors.15) Install the Connector Cover.16) Install the removed Cassettes.17) Check that the Environment Heater switch is ON.18) Plug the power plug of the host machine to the outlet.19) Turn ON the main power switch.
In case of 2-Cassette Unit
1) Remove the cassette. 2) Remove the Heater Connector Cover using a flat-blade screwdriver.
1 Claw 2 Protrusions
MEMO:When performing this procedure, it is not necessary to remove the Host Machine. However, the figure shows the picture with out the Host Machine to show easily.
Claw
Heater Connector Cover
Protrusions
F-9-171
9
99-74
9-74
3) Fit the claws (3 places) on the Cassette Heater Unit into the holes on the Base Plate, and then move it toward the front.
3 Claws
CAIUTION:
Be sure that the claws are fit into the holes of the Base Plate properly.
F-9-172
4) Tighten the removed screw (W sems round end;M3X6) with the stubby driver to connect the connector.
Connector
F-9-173
5) Install the heater Connector Cover.6) Install the removed Cassettes.7) Check that the Environment Heater switch is ON.8) Plug the power plug of the host machine to the outlet.9) Turn ON the main power switch.
9
99-75
9-75
Drum Heater-C1 Installation Procedure
Checking the ContentsConfirm the following components with correct quantities are contained in the carton.
[1]
[2][3]
[1] Drum heater Unit x 1[2] Wire saddle x 2[3] Edge saddle x 1
F-9-174
Points to Note Before Installation Turning Main Power OFF
CAUTION:
Perform the following in the order prior to the installation.
1) Turn the main power of the host machine OFF.
2) Confirm the control panel display and the main power lamp have turned OFF and unplug the power cord.
9
99-76
9-76
Installation Procedure
1) Turn the main power OFF and unplug the power cord from the outlet.
2) Open the front cover.
F-9-175
3) Push the button to open the right cover.
CAUTION:
To avoid any damage on the drum unit, keep the right cover open by 5 cm or more during installation.
F-9-176
4) Turn the lock lever as shown in the figureand remove the waste toner container.
F-9-177
5) Remove 1 screw from the developing pressure lever. The screw does not exist in some machine versions by destination.
6) Turn the developing pressure lever as shown in the figure and release the developing unit.
x1
F-9-178
7) Slowly draw out the drum unit by half as shown while gripping the lever beneath the drum unit handle.
F-9-179
9
99-77
9-77
8) Hold the drum unit as shown in the figure. Pull up the unit a little and draw it out completely.
F-9-180
9) Remove the 2 screws and release the claw to detach the toner replenish cover.
Claw
x2
x1
F-9-181
10) Detach 1 connector and draw the developing unit out.
x1
F-9-182
11) Dismount the harness from the developing stay and remove 2 screws to detach the developing stay. (Removed developing stay is no longer used.)
x2
F-9-183
9
99-78
9-78
12) Remove the rear cover (right). Screws (3 pcs.) Claws (2 pcs.)
Claws
x3
x2
F-9-184
13) Remove the connector cover. Screw (1 pc.)
x1
F-9-185
14) Detach all the connectors at the place shown in the figure. (This is performed only when the optional cassette unit is installed.)
F-9-186
15) Remove 1 screw (RS tight: M3) and release 1 claw to detach the rear cover (lower). Screw (1 pc.) Claw (1 pc.)
Claw
x1
x1
F-9-187
9
99-79
9-79
16) Draw out the paper cassette(s).17) Remove the left cover (lower).
*For the model with the 1st cassette capacity is 550sheets: Screws (2 pcs.)
*For the model with the 1st cassette capacity is 250sheets: Screws (3 pcs.) Claw (1 pc.)
x2
Claw
x3
F-9-188 F-9-189
18) Remove 1 screw from the left cover and distort it to detach the inner bottom cover. Screw (1 pc.)
x1
F-9-190
9
99-80
9-80
19) Remove the left cover to detach it. Screw (1 pc.)
CAUTION:
There is the link rod behind the left cover, which is engaged to the switch on the power supply unit. So carefully remove the left cover not to give an excessive lord on the link rod.
x1
Link rod
F-9-191
MEMO:When reinstalling the left cover, surely insert the link rod in the switch on the power supply unit so the switch does link to the main power switch of the host machine.
x1 x2
F-9-192
9
99-81
9-81
20) Remove 1 screw to detach the blindfold cover. Screw (1 pc.)
F-9-193
21) Remove the left rear cover. Screws (3 pcs.)
x3
F-9-194
22) Detach all the connectors on the power supply unit and remove 3 screws to dismount the power supply unit.
x3
F-9-195
23) Mount 2 supplied wire saddles and 1 supplied edge saddle on the rear frame.
F-9-196
9
99-82
9-82
24) Install the supplied drum heater unit in the host machine with 2 screws.
x2
F-9-197
MEMO:Insert the positioning pins of the drum heater unit to the holes of rear frame.
F-9-198
CAUTION:
Do not damage the pre-transfer guide when installing the drum heater unit.
F-9-199
9
99-83
9-83
25) Fit the harness on the harness guide of the drum heater unit as shown.
F-9-200
26) Fix the drum heater harness in the 2 wire saddles and 1 edge saddle.
x3
F-9-201
27) Joint the connector of the drum heater harness to J1104 on the heater PCB.
x1
F-9-202
9
99-84
9-84
28) Restore the power supply unit with 3 screws and joint all the connectors for it.29) Restore the toner replenish cover, the rear cover (right), the connector cover, the rear lower cover, the left lower cover, the left cover, the blindfold cover and the left rear cover.30) Restore the inner bottom cover and fix 1 screw to the left cover.
x1 x3
F-9-203
31) Restore the developing unit and joint the developing unit connector.32) Hold the drum unit handle and the part shown in the figure. Slowly draw it in till it stops.
CAUTION:
Confirm engagement of the drum unit and the drum unit rail of the host machine.
F-9-204
33) Turn the developing pressure lever to set the developing unit and fix 1 screw. The screw is not necessary if it is not removed at the step 5).
x1
F-9-205
9
99-85
9-85
34) Restore the waste toner container.
F-9-206
35) Lock the waste toner container.36) Close all the external covers.
F-9-207
9
99-86
9-86
Relocating the Machine
Required ArticlesHave the following articles on hand:
Fixing tapeDrum cover removed during installationOptical system fixing screws (2 pcs.) removed during installation (iR2545/2535 Series only)
Preparation for Relocating the MachineWhen moving the machine using stairs (including steps) or transporting the machine to a different place using a truck, go through the steps described below.
CAUTION:
When lifting the machine with a double-cassette pedestal, be sure to remove the double-cassette pedestal in advance.
If the machine is lifted with the double-cassette pedestal installed, they may separate from each other and consequently the machine can damage.
Work Procedure1) Remove the drum unit, and then attach the drum cover removed during installation.
F-9-208
2) For the iR2545/2535 Series, secure the optical system using the two screws removed during installation.
x2
3) Secure the front cover, toner supply cover, delivery section, and cassette with tape.4) Place an A3-size sheet on the document glass, and then secure the document glass cover
(ADF) with tape.
F-9-209
Service Tools General Circuit Diagram
Appendix
9
99-88
9-88
Service Tools Special ToolsTool name Tool No. Rank (*) Shape Uses
Digital multimeter FY9-2002 A For making electrical checks.
Tester extension pin
FY9-3038 A As an addition when making an electrical check.
Tester extension pin (L-shipped)
FY9-3039 A As an addition when making an electrical check.
NA-3 Test Chart FY9-9196 A For checking and adjusting images.
Mirror cleaning tool
FL2-9842 -- Used for cleaning the mirror in the CCD unit.This part is installed in the reader unit.(Not a service tool)
T-9-5
* A: each service engineer is expected to carry one. B: each group of 5 service engineers is expected to carry one. C: each workshop is expected to carry one.
Oils and SolventsName Uses Composition Remarks
Alcohol cleaning;e.g.,glass, plastic, rubber; external covers
fluoride-family hydrocarbonalcoholsurface activating agentwater
Do not bring near fire.Procure locally.IPA (isopropyl alcohol) may be substituted.
Lubricant scanner railstream reading glass
silicone oil KF96SS (300CS)FY9-6011 (50 cc)
T-9-6
9-89
9-89
General Circuit Diagram
General Circuit Diagram (1/7)
GND
GND
+24V
+24V
L-GN
D
+5R
P-G
ND
+24R
P-G
ND
+24U_LO
CK
CTR
L0_0
+3.3
V
DE
TEC
T
CTR
L0_2
CTR
L0_1
PW
M
GN
D
+5V
GN
D
BD
+5V
R
GN
D
1
GND
GND
ECO_DOUT
ECO_DIN
ECO_SCK
GND
ECO_CS
+3.3V
+3.3V
FRAM_WP
SPD_CLK
SPD_DAT
GND
23
GN
D
ES
S1
GN
D
+3.3
V
GN
D
GND
PO
LYG
ON
_M_A
CC
*
PO
LYG
ON
_M_F
G*
UI_
TXD
GN
D
UI_
RX
D
QV
GA
_LC
DE
N
QV
GA
_STA
RTP
+3.3
V
UI_
SO
FTS
W*
BK
LTO
N
QV
GA
_LA
TCH
P
RE
SE
T_U
I*
+3.3
R
GN
D
+5R
GN
D
+5R
GN
D
QV
GA
_XC
LK*
QV
GA
_UD
0
QV
GA
_UD
1
QV
GA
_UD
2
QV
GA
_UD
3
GN
D
GN
D
PO
LYG
ON
_M_D
EC
*
L_GND
DDI_ITOP_OUT*
IMG1L_IMAGE_END*
L_GND
IMG1L_TXD
IMG1L_RXD
L_GND
DDI_LIVEWAKE*
DDI_PI0
DDI_DOWNLOAD*
IMG_SYS_RST*
L_GND
DDI_RESET*
DDI_POWER*
DDI_CPRDY*
DDI_PPRDY*
L_GND
DDI_CTS*
DDI_RTS*
DDI_TXD
DDI_RXD
L_GND
DDI_PPRTST*
LASER_DETECT*
HAND_SET*
POLYGON_M_BD*
L_GND
+5V
C
+24V
R
GN
D
+5V
R
+24VR
CTR
L1_2
CTR
L1_1
CTR
L1_0
GN
D+24R
P_G
ND
Main Controller PCB (1/3)
DE
TEC
T
DA
TA_D
-
DA
TA_D
+
GN
D
DA
TA_A
+
DA
TA_A
-
GN
D
DA
TA_B
+
DA
TA_B
-
GN
D
DA
TA_C
-
DA
TA_C
+
GN
D
1413121110982 3 4 5 61 7
J8143
1413121110982 3 4 5 61 7
J601
21
J110
1
123
J2000
13 12 11 10 9 8 23456 17
J8142
10982 3 4 5 61 7
J602
23
1
J106
12
3
SW211 8 1234567910
J104
21
J107
11 8 1234567910
J8125
SO
LD6
SO
LD7
2
4 3
1
SW4
SO
LD4
SO
LD5
2 31
J108
12
34
56
78
910
1213
1415
1617
1819
2021
2223
2425
2627
11
J811
2
321
12
34
56
J000
1
12
34
56
J8115
12
34
56
78
J990
3
12
34
56
78
J8116
12345678910121314151617181920212223 11
J0003
1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 21 22 2311
J811412
34
56
78
910
1213
1415
1617
1819
2021
2223
2425
2627
11
J210
12345
J1
1 2 3 4 5
J208
1 2 3
J2
3456 12
J201
3456 12
J103
23
41
J507
14
32
J105
Laser Scanner Unit
DC Controller PCB (1/4)
Front Door Switch
Enviorment Switch
Power Supply PCB (1/3)
Heater PCB(1/2)
Reader RelayPCB (1/2)
Control Panel CPU PCB (1/2)
Soft-IDPCB
CounterROMPCB
F-9-210
9-90
9-90
General Circuit Diagram (2/7)
M
SL
M
M
M
2
3
DE
V_A
C_O
N*
P-G
ND
3 2 1 123
1 2 3
PS
U_D
ETE
CT1
*
PS
U_D
ETE
CT2
*
ZER
O_C
RO
SS
RE
LAY
_DR
IVE
*
HE
ATE
R1_
ON
*
HE
ATE
R2_
ON
*
FIX
_M_D
EC
*
FIX
_M_A
CC
*
GN
D
FIX
_M_F
G*
GN
D
GN
D
MA
IN_M
_AC
C*
MA
IN_M
_DE
C*
MA
IN_M
_FG
*
DC
_CLK
DIS
_CTR
L
FIX
_CTR
L
FIX
_N_D
RV
CH
RG
_DC
_CTR
L
DE
V_D
C_C
TRL
TR_C
C_C
TRL
TR_C
HG
HV
T_E
NB
CH
RG
_AC
_DR
V
CH
RG
_DC
_ON
TR_N
_DC
_ON
DIS
_DC
_ON
L-G
ND
+3.3
R
P-G
ND
P-G
ND
PS
U_F
AN
_ON
P-G
ND
PS
U_F
AN
_LO
CK
*
EN
V_H
EA
TER
_PR
INT*
L-G
ND
L_GN
D
+5R
L_GN
D
+5R
L_GN
D
MP
_WID
E_S
NS
+5R
L_GN
D
MP
_PA
PE
R_S
NS
+24R
MP
_SL_O
N
FAN
_F_ON
P-G
ND
FAN
_F_LOC
K*
FAN
_R_O
N
FAN
_R_LO
CK
*
DC Controller PCB (2/4)
+5R
L-GN
D
TON
ER
_CO
VE
R_S
NS
+5R
WA
STE
_TON
ER
_FULL_S
NS
+5R
P-G
ND
N.C
.
TR_P
_DR
V*
DE
V_A
C_D
RV
*
CH
RG
_AC
_CTR
L
CH
RG
_I_S
NS
DE
V_D
C_O
N
DO
OR
_MS
W
+24V
U_L
OC
K
+24V
U_L
OC
K
DE
VE
LOP
_LEV
EL_S
NS
+24R
L-GN
D
L-GN
D
+24R
HO
PP
ER
_LEV
EL_S
NS
HO
PP
ER
_M_O
N
BO
TTLE_M
_ON
P-G
ND
BO
TTLE_M
_LOC
K*
HO
PP
ER
_M_LO
CK
*
N.C
.
1212 3
FRE
E
P_P
OW
ER
_ES
S2
+24U
_LO
CK
+24U
_LO
CK
+24U
_LO
CK
LOO
P_S
NS
DU
PLE
X_S
NS
1
L-GN
D
123
1 2 3J2590
1 2J2008
2 3 4 51
J205
7 6 5 3 2 14
M1
123 J1103
12345678
1 2 3 4 5 6 7 8J2561
1 2
M6
1234 J2015 1234 J2013
1 2 3J2016
1 2 3J2014
18 17 16 15 14 13 12 11 10 9 8 23456 1719
J207
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
J204
12345678910111213141516171819202122232425
J301
1 2 3 4 5 6 7 8
J202
12345678
J101
12345678910121314151617181920 1121
321
S9
J2007
7654321 J2002
12
3
12
3J2
506
321J2009
321J2010
1 2 3 J2006
321 J2005 321 J2004
S6
1 2 3
FAN6
12345678910121314151617181920 1121
J206
1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 2011 21J2501
13121110982 3 4 5 61 7
J203
S8
5 4 3 2 1
M2
12345J2001
S7
2 1
SL2
3 2 1J2003
123
FAN4
123
FAN3
321 J2011321 J2012
9 8 23456 17
982 3 4 5 61 7J2502
21
M7
S17 S16
HVT PCB
Power Supply PCB (2/3)
Power Supply Cooling Fan
Fixing Motor Main Motor
Hopper MotorSub Hopper Toner Sensor Bottle Motor
Developing Unit Toner Sensor
Waste Toner Full Sensor
Toner Cover Open/Closed
Sensor
Exhaust Fan (Rear)
Exhaust Fan (Front)
Manual Feeder Paper Sensor
Manual Feed Pickup Solenoid
Manual Feeder Paper Size Sensor
Duplex Feed Sensor
Loop Sensor
TS1TS2
to Heater PCB
F-9-211
9-91
9-91
General Circuit Diagram (3/7)
CL CL
SL
M
CL
M
M
M
N.C
.
+5R
L-G
ND
RE
GIS
T_S
NS
DU
PLE
X_M
_A
DU
PLE
X_M
_A*
DU
PLE
X_M
_B
DU
PLE
X_M
_B*
MU
LTI_
CL_
ON
+24R
1 221 1 2
L-G
ND
+5R
21
L-G
ND
+3.3
R
EN
V_S
NS
_DA
TA
L-G
ND
EN
V_S
NS
_CLK
EN
V_S
NS
_DE
TEC
T*
3 2 1 1231234
+5R
L-G
ND
C_S
IZE
_L3
L-G
ND
C_S
IZE
_L2
C_S
IZE
_L1
C_S
IZE
_W3
L-G
ND
C_S
IZE
_W2
+5R
L-G
ND
CS
T_FE
ED
_SN
S
+5R
L-G
ND
CS
T_P
AP
ER
_SN
S
+5R
L-G
ND
C_S
IZE
_L4
+24R
+24R
RE
GIS
T_C
L_O
N
+24R
SLE
EV
E_C
L_O
N
DC Controller PCB (3/4)
+5R
L-GN
D
EX
IT1_FULL_S
NS
+5R
L-GN
D
EX
IT1_SN
S
ED
GE
_FAN
_ON
P-G
ND
ED
GE
_FAN
_F_LOC
K*
ED
GE
_FAN
_ON
P-G
ND
ED
GE
_FAN
_R_LO
CK
*
SH
UTTE
R_M
_A
SH
UTTE
R_M
_A*
SH
UTTE
R_M
_B*
+5R
L_GN
D
C_S
IZE
_W1
C_S
IZE
_W4
CS
T_FE
ED
_SL_
ON
PA
PE
R_L
EV
EL_
B_S
NS
PA
PE
R_L
EV
EL_
A_S
NS
SH
UTTE
R_H
P_S
NS
FEE
D_M
_A*
FEE
D_M
_A
FEE
D_M
_B*
FEE
D_M
_B
SH
UTTE
R_M
_B
DO
OR
_SN
S
EX
IT1_M_B
*
EX
IT1_M_B
EX
IT1_M_A
EX
IT1_M_A
*
N.C
.
121110982 3 4 5 61 7
J212
1234567
1 2 3 4 5 6 7J2507
123456
J2026
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
J211
10 9 8 23456 17J2532
13 12 11 10 9 8 23456 17
J215
10 9 8 23456 17
J213
1 2 3J2545 123
654321
M3
1 2 3 4
J2017
1413121110982 3 4 5 61 7
14 13 12 11 10 9 8 23456 17J253310982 3 4 5 61 7
1 2 3
J2033321
J2032
4321
J2031
J20292 12 1
J2028J202712 4 3 2 1
M4
J2030
M9
12 J2025123
J2024
3 2 1
J2023
2 1
J2022
123
J202112345
J2020
12345
J2019
4321
1 2
CL2
982 3 4 5 61 7
J209
123
S18
J2018
4 3 2 1
M8
J2037 J2036 J20351 2 3321
123
FAN1
321
J2039
S10
3 2 1
FAN2
21
SL1
3
S2S1 S3S4
21
CL3
1 2
CL1
S12 S11
8 7 6 5 4 3 2 1
J299
3 2 1
J2034
S5
Enviorment Sensor
Front Cover Open/Closed
Sensor
Pre-Registration Sensor
Cassette 1 Pickup Sensor
Cassette 1 Paper Sensor
Cassette 1 Paper Level
Sensor B
Pickup Solenoid Cassette 1 Pickup Motor
Registration Clutch
Developing Cylinder Clutch
Manual Feed Pickup Clutch
Duplex Feed Motor
HU1
Cassette 1 Paper Level
Sensor A
Shutter HP Sensor
Shutter HP Motor Paper Edge
Cooling Fan (Rear)
No.1 Delivery Sensor
No.1 Delivery Full Sensor
No.1 Delivery Motor
Paper Edge Cooling Fan
(Front)
Cassette Size Detection Switch 1
SW6
Cassette Size Detection Switch 2
SW7
F-9-212
9-92
9-92
General Circuit Diagram (4/7)
TP
OP
1_D
ETE
CT
OP
2_D
ETE
CT
P-GND
+24R
+5R
OP
1_E
X_L
OA
D
OP
1_E
X_S
EN
D
OP
1_E
X_C
LK
L-G
ND
L-G
ND
OP
1_M
1_C
LK
RE
SE
T*
+5R
OP
2_M
2_C
LK
L-G
ND
L-G
ND
L-G
ND
L-G
ND
L-G
ND
FIN
_BIT
FIN
_EN
AB
LE
FIN
_DL_
RE
SE
T
L-G
ND
N
N
H
H
H2
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
HN
N.C
.
N.C
.
CO
M
H1
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
N.C
.
FIN
_TxD
L-G
ND
FIN
_RxD
L-G
ND
FIN
_MO
DE
L-G
ND
P-G
ND
L-G
ND
+24R
OP
2_R
EA
DY
OP
2_E
X_S
EN
D
OP
1_R
EA
DY
RE
SE
T*
L-G
ND
OP
2_M
1_C
LK
L-G
ND
OP
2_E
X_C
LK
+24R
L-GN
D
RE
VE
RS
E_S
NS
EX
IT2_FULL_S
NS
EX
IT2_SN
S
RE
VE
RS
E_M
_CW
CC
W
RE
VE
RS
E_M
_CLK
RE
VE
RS
E_M
_I1
RE
VE
RS
E_M
_I0
M_S
TAN
DB
Y*
EX
IT2_DE
TEC
T*
+3.3R
L-GN
D
L-GN
D
+24R
P-G
ND
P-G
ND
GN
D
ES
S
N.C
.
N.C
.
OP
2_E
X_L
OA
D
+24V
R2
GN
D
+5R
L-GN
D
FIX_O
UT_S
NS
L-GN
D
MA
IN_TH
L-GN
D
SU
B1_TH
L-GN
D
SU
B2_TH
L-GN
D
TH_D
ETE
CT*
+5R
P-G
ND
Option Power Supply PCB
RE
VE
RS
E_S
L_ON
EX
IT2_SL_O
N
MT5
2 1
J9913
23
45
1
J1104
15 14 13 12 11 10 9 8 23456 17
12
J1102
12
J113A12
J113B
1110982 3 4 5 61 7
J22421
J221
21
J99091 2
J704
21
J703
23456 1
J9912
2 1
J9916
J2063
21
J991
4
12345678
1 2 3 4 5 6 7 8
181716151413121110982 3 4 5 61 7 19 J2504
23
1J2
505
23
1
18 17 16 15 14 13 12 11 10 9 8 23456 1719
J220
11 10 9 8 23456 17J9911 J9910
11 10 9 8 23456 17
J9908
1110982 3 4 5 61 7
J226
ET6
ET5
ET4
ET3
ET1
23456 1
J9911
23 1
J110
234567 1
J1106
21
J222
21
J9907D
21 J2101
23 1
J109
2 1 J2100
10 9 8 23456 17
J2510LA
MT6
56 4 123J2510DWH
3 2 146 5J2510LWH
10982 3 4 5 61 7
J2510DA
1 2
J9915
ET2
2 31
J1105
13 2
J701
12
TP1
MT4
7 16 5 4 3 289
J2510LB
MT8
MT3
UNIT1
12
H2
MT2
21 H
1
MT7
982 3 4 5 61 7
J2510DB
1 2 3 J20461
2TH
3
12
TH2
21 TH
1
11 10 9 8 23456 17
J214
S19
151413121110982 3 4 5 61 7
J223
DC Controller PCB (4/4)
Power Supply PCB (3/3)
Fixing Sub Thermistor
(Rear)
Fixing Sub Thermistor
(Front)
Fixing Main Thermistor Fixing Outlet Sensor
Fixing Heater 1
Fixing Heater 2
Finisher Controller PCB
Heater PCB(2/2)
to Cassette Heater
to Cassette 2 to Cassette 1
to 2 Way Unit
to Reader Heater
F-9-213
9-93
9-93
General Circuit Diagram (5/7)
PS
PS
M
PS
PS
GN
D
N.C
N.C
N.C
LED
_BA
R_2
+24V
U
N.C
N.C
N.C
GN
D
GN
D
GND
GND
GN
D
FFC
_OU
T
FFC
_IN
GN
D
GN
D
TCLK
+
TCLK
-
TX2-
GN
D
TX2+
TX1-
GN
D
TX1+
TX0-
GN
D
TX0+
GN
D
SH
_R
AF_
SIO
_CLK
AF_
SIO
_XC
E
AF_
SIO
_DO
AF_
SIO
_DI
EE
P_C
S0
EE
P_C
LK
EE
P_T
X
EE
P_R
X
*RE
SE
T
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
GN
D
TX0+
GN
D
TX0-
TX1+
GN
D
TX1-
TX2+
GN
D
TX2-
TCLK
-
TCLK
+
GN
D
GN
D
GN
D
FFC
_OU
T
GN
D
SIZE0
GND
GND
HP_SENS
+3.3V
GND
CVR_OPEN_S1
+3.3V
+24V
GN
D
MO
T_C
LK
MO
T_C
WM
MO
T_E
MB
OP
M/R
KM
OT_
CLK
OP
M/R
KM
OT_
CW
B
OP
M/R
KM
OT_
EN
B
OP
M/R
KM
OT_
VR
EF1
RK
MO
T_V
RE
F2
MO
T_P
WM
RK
MO
T_S
TB
RIK
AN
_SO
L
STM
P_S
OL
RE
G_C
L
PIC
K_C
L
SE
T_LE
D
GN
D
FAN
FAN
_LO
CK
AD
F_JO
INT
DF_
SIZ
E_W
1
DF_
SIZ
E_W
2
DF_
SIZ
E_L
1
DF_
SIZ
E_L
2
LAS
T
RE
AD
RE
G
TIM
ING
EX
IT
EM
PTY
CO
VE
R
RK
MO
T_H
P
GN
D
+5V
S
+5V
+5V
3.3V
3.3V
DF_
CO
VE
R_S
EN
S
RK
MO
T_H
P
EM
PTY
_SE
NS
EX
IT_S
EN
S
TIM
ING
_SE
NS
RE
G_S
EN
S
RE
AD
_SE
NS
GN
D
LAS
T_S
EN
S
DF_
SIZ
E_L
2
DF_
SIZ
E_L
1
DF_
SIZ
E_W
2
DF_
SIZ
E_W
1
GN
D
AD
F_JO
INT
FAN
_LO
CK
FAN
MO
T_V
RE
F
SE
T_LE
D
RE
G_C
L
PIC
K_C
L
STM
P_S
OL
RIK
AN
_SO
L
RK
MO
T_S
TAN
BY
MO
T_P
WM
GN
D
RK
MO
T_V
RE
F2
OP
M/R
KM
OT_
VR
EF1
OP
M/R
KM
OT_
EN
B
OP
M/R
KM
OT_
CLK
OP
M/R
KM
OT_
CW
B
GN
D
N.C
MO
T_E
NB
MO
T_C
WB
MO
T_C
LK
GN
D
OP
M_S
TAN
BY
24V
_WA
TCH
CV
R_O
PE
N_S
1
CV
R_O
PE
N_S
0
HP
_SE
NS
SIZ
E3
SIZ
E2
SIZ
E1
SIZ
E0
SIZ
E_O
N
5V 5V 5VLED
2_O
N
LED
1_O
N
CLK
_SE
L
GN
D
3.3V
GN
D
5V5VGN
D
GN
D
12V
GN
D
+24V
S
+24V
S
+24V
U
LED
_BA
R_1
LED
_BA
R_1
LED
_BA
R_2
+3.3V
/A
/B
A
B
CVR_OPEN_S0
SIZE1
GND
SIZE1
+5V
+5V
SIZE0
GND
OP
_FFC
_IN
GN
D
GN
D
GN
D
N.C
OP
_FFC
_OU
T
N.C
FFC
_IN
GN
D
*RE
SE
T
EE
P_R
X
EE
P_T
X
EE
P_C
LK
EE
P_C
S0
GN
D
AF_
SIO
_DI
AF_
SIO
_DO
AF_
SIO
_XC
E
AF_
SIO
_CLK
SH
_R
CLK
_SE
L
GN
D
3.3V
N.C
GN
D
5V5VGN
D
GN
D
7 16 5 4 3 28910
J55348 46 44 42
47 45 43 41 39
40 22 14 12
37 35 33 31 29 27 25 23 21 19 17 15 13 11
10
9
8
7
6
5
4
3
2
1
16182026283032343638 24
49
50
J552
32
1
S2932
1
J573
12
3 S28
12
3
J574
12
34
56
J514
65
43
21
J508
34
56
12
J556
23
45
1
J506
65
43
21
M21
64 60
59
58 48 46 44 42
47 45 43 41 39
40 22 14 12
37 35 33 31 29 27 25 23 21 19 17 15 13 11
10
9
8
7
6
5
4
3
2
1
16182026283032343638 24
49
50
51535557
52545662
63 61
J8141
98
23
45
61
7
J505
12
34
56
J509
10982 3 4 5 61 7
J503
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
J554
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
J504
50
49
24 38363432302826201816
1
2
3
4
5
6
7
8
9
10
11 13 15 17 19 21 23 25 27 29 31 33 35 37
12 14 22 40
39 41 43 45 47
42 44 46 48J501
48 46 44 42
47 45 43 41 39
40 22 14 12
37 35 33 31 29 27 25 23 21 19 17 15 13 11
10
9
8
7
6
5
4
3
2
1
16182026283032343638 24
49
50
J8113
61 63
62565452
57555351
50
49
24 38363432302826201816
1
2
3
4
5
6
7
8
9
10
11 13 15 17 19 21 23 25 27 29 31 33 35 37
12 14 22 40
39 41 43 45 47
42 44 46 48 58
59
60 64J512
12
J561
2 1
J5115049
2438 36 34 32 30 28 26 20 18 16
1
2
3
4
5
6
7
8
9
10
1113151719212325272931333537
12142240
3941434547
42444648
J502
32
1
S24
12
3
J569
32
1
J575
12
3
S21
32
1
S26
12
3
J565
32
1
J555
32
1
S22
32
1
J559
12
3 S25
65
43
21
J513
CCD PCB
Main Controller PCB (2/3)
Original Size Sensor 1 (A/INCH)
Original Size Sensor 0 (A/AB)
Original Size Sensor 0 (AB/INCH)
Original Size Sensor 1 (AB/INCH)
CCD HP Sensor
Copyboard Cover Open/Closed Sensor 0
Copyboard Cover Open/Closed Sensor 1
Scanner Motor
Reader Relay PCB (2/2)
ADF Driver PCB
F-9-214
9-94
9-94
General Circuit Diagram (6/7)
USB(H)
J8103 J8110SDcard
J8104USB(D)
J8111LAN
Bat
tery
(+)
(-)
Sec
onda
ry
J812412
N.C
.
GN
D
2022
21 19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
GN
D
GN
D
VH(+)
AG
ND
+12V
SN
OO
P
TX_O
UT
RX
_IN
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
J1
+5V
GN
D
+3.3
V
CIV
S
DC
LIM
SR
D
PR
D
HR
D
CM
LD
LPR
D
CI1
CI2
N.C
.
HO
OK
1
HO
OK
2
CA
IDD
LPL1
LPL2
IPS
EL
N.C
.
+5V
1
VH(-)
CT1
CT2
T2
N.C.
L1
L2
T1
1
GND
GND
GND
CARD_READER_RX
CARD_READER_TX
CARD_READER_COUNT
+5V
B_CRDY
C_CRDY
B_PRDY
C_PRDY
COIN_TX
COIN_RX
VOUT1
VOUT2
GND
VCC(5Vor3.3V)
GND
GND
CCVI_OPTION
CCVI_CL_BW_L
CCVI_KYU_COUNT
CCVI_CP_ENB
+5V
J8149
J8127
J8103
GN
D
CCVI_LARGE_SMALL_B
CIC
NT_
OU
T
+24V
GN
D
J2
USB
USB(H)
+24V
MODEM PCB
123456
J8147
12
34
56
7
J3
FFC3
21
J8134
1 2 3 4
J00121
J002
1110
98
23
45
61
7
J000
21
23
45
67
J990
4
12
34
56
7
J81171
2
J8140
2
1 SP1
98
23
45
61
7
J8118
12
34
5
J990
1
12
34
5
J8119
123
J8146
12
34
56
7
J004
1 2 3 4 5 6
J02
21
J4
23
1
J003
21
J9999
21
J112
12
Modular PCB
NCU PCB
FAX BOX
Main Controller PCB (3/3)
Speaker (Option)
to Power Supply PCB
Card Reader
to Coin Vendor
Control InterfaceCable
USB hub PCB
F-9-215
9-95
9-95
General Circuit Diagram (7/7)
SOLDER
VLC
G
ES
S-K
EY
L-R
TN0
L-D
GT2
L-D
GT1
L-D
GT0
K-R
TN0
K-D
GT2
K-D
GT1
K-D
GT0
PO
WE
R-L
ED
L-D
GT4
L-D
GT3
K-R
TN4
K-R
TN3
K-R
TN2
K-D
GT6
K-D
GT5
K-D
GT4
K-D
GT3
Key Top PCB Assembly
12
3
24
68
1012
14
13
57
911
13
J4
23
12
1 3 5 7 9 11 13 15 17 19 21 23
24
13
1234567891011121314151617181920212223
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
J3
2 4 6 8 10 12 14 16 18 20 22 24
25
26
27
J6
J5J7
BKLT_ON*
J1
J955
-24V
EE
P-G
ND
K-D
GT7
K-R
TN1
L-D
GT5
L-R
TN1
VLC
D
+5R
TTP-L
TTP-D
TTP-R
TTP-U
Contorol Panel
J11
1 2 3 4
SO
LDE
R
N.C.
YD
LP
XSCL
+5R
L-GND
-24VEE
D0
DOFF*
D1
D2
D3
-24VEE
VLCD
1/4 Inverter PCB
Control Panel CPU PCB
to Main Controller PCB
LCD
CCFL
Touch Panel
F-9-216