Manual: Rosemount® 1595 Conditioning Orifice · PDF fileReference Manual 00809-0100-4828, Rev EB iii Rosemount® 1595 Conditioning Orifice Plate NOTICE Read this manual before working

  • Upload
    buidan

  • View
    233

  • Download
    0

Embed Size (px)

Citation preview

  • Reference Manual00809-0100-4828, Rev EB

    May 2014

    Rosemount 1595 Conditioning Orifice Plate

  • Reference Manual 00809-0100-4828, Rev EB

    Rosemount 1595 Conditioning Orifice Plate

    NOTICE

    Read this manual before working with the product. For personal and system safety, and for optimum product performance, make sure you thoroughly understand the contents before installing, using, or maintaining this product.

    The United States has two toll-free assistance numbers and one International number.

    Customer Central1-800-999-9307 (7:00 a.m. to 7:00 P.M. CST)

    International1-(952) 906-8888

    National Response Center1-800-654-7768 (24 hours a day)Equipment service needs

    The products described in this document are NOT designed for nuclear-qualified applications. Using non-nuclear qualified products in applications that require nuclear-qualified hardware or products may cause inaccurate readings.

    For information on Rosemount nuclear-qualified products, contact your local Emerson Process Management Representative.

    iii

  • iv

    Reference Manual00809-0100-4828, Rev EB

  • v

    Reference Manual 00809-0100-4828, Rev EB

    Table of ContentsMay 2014

    Table of Contents

    1Section 1: Introduction1.1 Using this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

    1.2 Receiving and inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

    1.3 Returning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

    2Section 2: Installation2.1 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

    2.1.1 Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

    2.2 Location and orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

    2.2.1 Horizontal pipe installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

    2.2.2 Vertical pipe installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

    2.2.3 1595 straight pipe requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

    2.3 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    2.3.1 Rosemount 1595 types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    2.3.2 Rosemount 1496 types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

    AAppendix A: Reference DataA.1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

    A.1.1 Performance specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

    A.1.2 Functional specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

    A.1.3 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

    A.2 Dimensional drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

    A.3 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

    BAppendix B: Product CertificationsB.1 Approved Manufacturing Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

    B.2 European Directive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

    B.2.1 European Pressure Equipment Directive (PED) (97/23/EC) . . . . . . . . . . . .25

    B.3 Hazardous Locations Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

    Table of Contents

  • vi

    Reference Manual00809-0100-4828, Rev EB

    Table of ContentsMay 2014

    Table of Contents

  • Reference Manual 00809-0100-4828, Rev EB

    Section 1: IntroductionMay 2014

    Section 1 Introduction

    Using this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1Receiving and inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1Returning the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1

    1.1 Using this manual

    This product manual provides installation, configuration, calibration, troubleshooting, and maintenance instructions for the Rosemount 1595 Conditioning Orifice Plate.

    Section 1: Introduction

    Section 2: Installation

    Appendix A: Reference Data

    Appendix B: Product Certifications

    1.2 Receiving and inspection

    Flowmeters are available in different models and with different options, so it is important to inspect and verify that the appropriate model was delivered before installation.

    Upon receipt of the shipment, check the packing list against the material received and the purchase order. All items are tagged with a model number, serial number, and customer tag number. Report any damage to the carrier.

    1.3 Returning the product

    To expedite the return process, call the Rosemount National Response Center toll-free at 800-654-7768. This center, available 24 hours a day, will assist you with any needed information or materials.

    The center will ask for the following information:

    Product model

    Serial numbers

    The last process material to which the product was exposed

    1Introduction

  • Reference Manual00809-0100-4828, Rev EB

    Section 1: IntroductionMay 2014

    The center will provide

    A Return Material Authorization (RMA) number

    Instructions and procedures that are necessary to return goods that were exposed to hazardous substances

    NoteIf a hazardous substance is identified, a Material Safety Data Sheet (MSDS), required by law to be available to people exposed to specific hazardous substances, must be included with the returned materials.

    2 Introduction

  • Reference Manual 00809-0100-4828, Rev EB

    Section 2: InstallationMay 2014

    Section 2 Installation

    Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3Location and orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8

    2.1 Safety messages

    Instructions and procedures in this section may require special precautions to ensure the safety of the personnel performing the operations. Please refer to the following safety messages before performing any operation in this section.

    2.1.1 Checklist

    The following is a summary of the steps required to complete a 1595 installation.

    If this is a new installation, begin with Step 1.

    If the mounting is already in place, verify that the orifice flange size and rating match the recommended specification and begin with Step 4.

    1. Determine where the 1595 is to be placed within the piping system.

    2. Establish the proper orientation as determined by the intended service for the orifice plate.

    3. Orient the 1595 Conditioning Orifice Plate so the pressure taps are centered between any two (of four) orifice bore holes. In addition, the pressure taps should be located at 90 to the plane of the last elbow.

    4. Review Location and orientation on page 4.

    5. Measure the pipes internal diameter (I.D.), preferably at 1 x I.D. from the orifice flange (upstream or downstream).

    Failure to follow these installation guidelines could result in death or serious injury:

    Make sure only qualified personnel perform the installation. Remove pressure and drain the pipe assembly prior to installing or removing the

    orifice plate. If the process fluid is caustic or otherwise hazardous, follow the instruction closely to

    prevent mishap.

    3Installation

  • Reference Manual00809-0100-4828, Rev EB

    Section 2: InstallationMay 2014

    NoteProviding the pipes I.D. at the time of purchasing the 1595 is necessary to maintain published orifice plate accuracy.

    6. Install the orifice plate.

    7. Check for leaks.

    8. Commission the orifice plate.

    9. Confirm the 1595 is installed so that it is centered in the pipes as recommended by ISO-5167.

    2.2 Location and orientation

    The orifice plate electronics must be installed in the proper orientation relative to the pipe and the fluid measured.

    2.2.1 Horizontal pipe installation

    Operating temperature limits

    For line sizes 2-in. (50 mm) to 24-in. (600mm)

    Temperature Range:

    -320 to 800 F (-196 to 427 C) and differential pressure up to 800 inH2O.

    800 to 1200 F (427 to 649 C) and differential pressure up to 400 inH2O.

    Pressure tap orientation

    Orient the 1595 Conditioning Orifice Plate so that the pressure taps are centered between any 2 (of 4) orifice bore holes. In addition, the pressure taps should be located at 90 to the plane of the last elbow.

    The following figures show paddle style conditioning orifice plate, but orienta