manual de servicio haier l42f6

7/26/2019 manual de servicio haier l42f6

1/31

LCD TV

OWNER'S MANUALMODEL: L32F6/L42F6

Please READ this manual carefully before

operating your TV, and retain it for future

reference

loaded from www.Manualslib.commanuals search engine
http://www.manualslib.com/http://www.manualslib.com/


2/31



3/311

Know these safety symbols

This bolt of lightning indicates uninsulated material within your unit may cause anelectrical shock. For the safety of everyone in your household, please do not removeproduct covering.

The exclamation point calls attention to features for which you should read theenclosed literature closely to prevent operating and maintenance problems.

placed on this apparatus.CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.

local regulations.

WARNING : To reduce the risk of fire or electric shock, this apparatus should not beexposed to rain or moisture and objects filled with liquids, such as vases, should not be

Please be sure to dispose of this set in accordance with all state and

End of life directives - Recycling

companies can dismantle and recycle this set. This will minimize the amount of materials being disposed of.

for new uses. At the end of it s life,specializedYour new TV contains several materials that can be recycled



4/312

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any of the ventilation openings.

Install in accordance with the manufacturers instructions.

Do not Install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

Do not defeat the safe ty purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and third grounding prong. The wide blade or third

prong are provided for your safety. When the provided

for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles , and the

point where they exit from the apparatus.

manufacturer.

Use only with a cart, stand, tripod, bracket, or

the apparatus. When a cart is used. Use caution when

moving the cart/apparatus combination to avoid injury

from tip-over.

Unplug this apparatus during lightning storms or when

unused for long periods of time.

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, li quid

has been spilled or objects have fallen into apparatus, t he

apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Damage Requiring Service- The appliance should be

A. The power supply cord or the plug has been damaged;

B. Objects have fallen, or liquid has been spilled into the

appliance;

C. The appliance has been exposed to rain

D. The appliance does not appear to operate normally or

exhibits a marked change in performance;

E. The appliance has been dropped, or the enclosure

damaged.

Tilt/Stability- All televisions must comply with

recommended international global safety standards for

tilt and stability properties of its cabinet design.

applying excessive pull force to the front , or top, of

the cabinet which could ultimately overturn the

product.

placing electronic equipment/toys on the top of the

cabinet. Such items could unsuspectingly fall from

the top of the set and cause product damage and/or

personal injury.

Wall or Ceiling Mounting- The appliance should be

mounted to a wall or ceil ing only as recommended by

the manufacturer.

Power Lines- An outdoor antenna should be located

away from power lines.

Outdoor AntennaGrounding- If an outside anten-

na is connected to the receiver, be sure the antenna

system is grounded so as to provide some protection

against voltage surges and built up static charges.

Object and Liquid Entry- Care should be taken so

that objects do not fall and liquids are not spilled into

the enclosure through openings.

Battery Usage CAUTION- To prevent battery

leakage that may result i n bodily injury, property dam-

age, or damage to the unit:

marked on the unit.

alkaline, etc.).

long time.

For ventilation, leave at least 4 to 6 free all around

the TV. Do not place the TV on a carpet.

The equipment shall not be exposed to dripping or

splashing.

The equipment shall not be exposed to rain or mois-

be placed on the apparatus.

The apparatus must be connected to a mains socket

outlet with a protected earthed connection.

The appliance coupler is used as the disconnect device

of this apparatus, the disconnect device shall remain

readily operable.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

amplifiers) that produce heat.

plug does not fit into your outlet, consult an electrician

Only use attachments/accessories specified by the

table specified by the manufacturer, or sold with

Refer all servicing to qualified service personnel. Servicing

serviced by qualified service personnel when:

ture and objects filled with liquids, such as vases, shall



5/313

ADDITIONAL SAFETY PRECAUTIONS

Ensure that LCD TV stand is tightened properly to the set on the right way of tightening of

the screw of the stand to the set. Improper tightening of screw may render the set unsafe.

If LCD TV is Installed on the wall, Installation should be carried out by qualified servicemen. Improper or incorrect

Installation may render the set unsafe.

Disconnect main plug when : cleaning the TV screen, never use abrasive cleaning agents .

there is a l ightning storm.

the set is left unattended for a prolonged period of time.

Do not shift or move the LCD TV around when it is powered on.

Do not touch, push or rub the surface of the LCD screen with any sharp or hard objects.

When the surface of the LCD screen becomes dusty, wipe it gently with an absorbent cotton cloth or

other soft material like chamois. DO NOT USE acetone, toluene or alcohol to clean the surface of the screen.

These chemicals will cause damage to the surface.

Wipe off water or saliva as soon as possible. These liquids can cause deformation and color fading of the

LCD screen when left exposed for some time.

Be careful of condensation when temperature changes occur. Condensat ion can cause damage to the LCD

screen and electrically part s. After condensation fades, spots or blemishes will be present on the LCD screen.

POSITIONING THE LCD TELEVISION

Place the LCD TV on a solid, sturdy base or stand. Be sure the stand is strong enough to handle the weight of

the LCD TV.

Try to leave at least 6 of space around each side of the LCD TV cabinet to allow for proper ventilation.

Do not place the LCD TV near a radiator or other sources of heat.

Do not place the LCD TV where it can be exposed to rain or excessive moisture.

RECYCLING PROCEDURE/END OF LIFE DISPOSAL

To minimize harm to the environment, the batteries supplied with the LCD TV do not contain mercury or

nickel cadmium. If possible, when disposing of batteries, use recycling means available in your area.

The LCD TV uses materials that can be recycled. To minimize the amount of waste in the environment, check

your area for companies that wi ll recover used televisions for dismant ling and collection of reusable mater ials,

or contact your dealer for TV recycling tips.

Please dispose of the carton and packing material through the proper waste disposal management in yourarea.

Precaution



6/314

Contents

Guide for Preparatory Work

IMPORTANT SAFETY INSTRUCTIONS .................................................. 2

Read before operating equipment ............................................................ 2Precaution ................................................................................................. 3

Panel control and rear terminal control ..................................................... 5

Preparation of remote control ................................................................... 7

Descriptions of remote control function .................................................... 8

Connection and preparation of the TV set ................................................ 9

Backboard singal source interfaces ........................................................ 10

Side signal source interfaces ...................................................................11

Preset and watch TV

Power On/Off .......................................................................................... 12

Selecting input signal for TV program ..................................................... 12

Using Menu functions

Menu operation ....................................................................................... 13

PICTURE MENU .................................................................................... 14

AUDIO MENU ......................................................................................... 15

FEATURE MENU .................................................................................... 15

INSTALLATION MENU ........................................................................... 16

VGA MENU ............................................................................................. 17

Multimedia feature setting(USB) ............................................................. 18

Establish and use the channel favorite list .............................................. 19

Others

Troubleshooting ...................................................................................... 20

Glossary .................................................................................................. 21

Care And Cleaning .................................................................................. 22

Product specications ............................................................................. 23

** Due to the product improvement, the screen display and illustrationsmay differ from the actual ones.



7/315

Explanations:The following illustration is for your convenience to recognize where all terminals are

located and to connect peripheral equipment; due to the product improvement, the

indications may be different from the actual one. The actual indications shall prevail.

Side control panelSide control panel

6

2

3

4

1

5

Explanations on the keys on the side of the TV set and theirfunctions

1 INPUT:Press to select the input source,then Press VOL+ or the ok of RC to

change the input source; while in standby mode, the input may be

used to turn on the TV set.

2 MENU:Press to open or exit the on-screen menu.

3 VOL+/-:

In TV mode: Press to increase (+) or decrease (-) the volume;

In TV menu: Move right (+) or move left (-) in the options.

4 CH+/-:

In TV mode: Press to increase (+) or decrease (-)the channel number ;

In TV menu: Move up (+) and down (-) in the options; while in standbymode, the

Channel +/- may be used to turn on the TV set.

5 POWER:Press to turn on / off (standby) the TV set.

6 : Switch it on before use TV.

Panel control and rear terminal control



8/316

Side and rear terminals

541

7 6

32

98 107

VIDEOLR

AV IN 2

USB

HDMI 3

Explanations on the rear terminals and their functions:

1 COMPONENT: Color aberration component (YCbCr, YPbPr) Video/

Audio Input Terminal

2 AUDIO IN: VGA audio input terminal

3 PC IN: VGA video input terminal

4 AV IN 1: AV IN 1 audio/video input terminal

5 AV OUT: AV audio/video output terminal

TV ANTENNA: Antenna input terminal

HDMI1/HDMI2/HDMI3 input terminal

AV IN 2: AV IN 2 audio/video input terminal

Earphone output socket

USB

Panel control and rear terminal control

32

6

7

8

9

10



9/317

Preparation of remote control

Installation of remote control batteries

As shown in the following diagram, put the remote control upside down and push open thebattery chamber.

Insert 2 AAA batteries as shown in the following diagram.(The positive and negative polesmust correspond to the indication).

Put back the battery chamber cover in place.

31 2

Never use rechargeable batteries, such as nickel-cadmium batteries.Suchbatteries are different in shape and performance, proper operation is thereforehard to be ensured.Please properly dispose the waste batteries in a environmentally friendly way.

Precautions for the use of batteries:Improper use of batteries may cause battery leakage, which may corrode the remote controlor cause battery explosion.The following precautions must be obeyed:Always replace batteries in pairs, i.e. replace a pair of old batteries with a pair of new

ones.Never use a new batteries together with an old one.Never use batteries of different types together, e.g. use a "zinc carbonate" battery together

with an "alkaline" battery.Never recharge, short circuit, reassemble, heat or burn used batteries.It is necessary to change batteries only when the remote control operates well or bad

occasionally or fails to control the operation of the TV set.If you don't use the remote control for a long period, take the batteries out of the remote

control so as not to cause battery leakage thus damaging the remote control.

Precautions while using remote controlEnsure no other objects are between the remotecontrol and the remote receiver of the TV set.

The remote control can not be kept in hot orhumid environment, otherwise violent impactmay cause the remote control failure.

Sunlight or other strong light may interfere

the signal sent by the remote control.In this

case, please turn the TV set towards the other

direction.

Use two AAA (7#) 1.5V alkaline batteries. Donot use different types of batteries together.Mount the batteries as per correct polarity.



10/318

Descriptions of remote control function

Using remote control

?

SCAN

F REEZ E P .M ODE S.M ODE ARC

H.LOCK

SOURCE

OK

DISPLAY

USB BACK

REC

REV FWD PREV NEXT

TEXT MIX SUBCODE HOLD

PIP SWAP MOVE ZOOM

TIMESHIFT PLAY/PAUSE HELP

INDEX

SLEEP FAVORITE

HDMI

/

KEY Introduction

POWER Press to turn on/off the TV.

HDMI Press to choose HDMI source mode.

FREEZE Freeze or unfreeze a piece of screen.

P.Mode Press to choose the Auto picture Mode.

S.Mode Press to choose the Auto sound Mode.

SLEEPPress to set sleep timer, setting amount of time beforeyour TV turn off automatically.

I/IISwitch stereo or mono mode in Stereo program, selectDual I or Dual II in dual language program.

0-9 Press to enter TV channel number to select channel.

RECALLPress to display the previous channel or source, orreturn the previous menu when the menu is displaying.

VOL+/- Press + or - to adjust the volume.

SOURCE The Source List should be activated and show on OSD.

MUTE Switch the sound ON/OFF.CH / V Press or V to browse through the TV channels.

/

/ /

Press the keys to navigate OSD menu.

OK1. Press button to activate the setting/selection of OSD.2. Press to return previous level.

MENU1. Press to activate OSD menu or back to previous

level of OSD.2. Exit OSD.

USB Press to choose USB source mode.

PLAY/PAUSE Start or stop a Music/picture/video of playing.

REV Fast Reverse(only for USB).

FWD Fast Forward(only for USB).

PREV Select previous Music/picture/video (only for USB).

NEXT Select next Music/picture/video (only for USB).ARC Press this key to select the screen display proportion.

Display Display or close the current input source information.

EXIT Exit current menu.

SCAN No available

ZOOM No available

H.LOCK No available

FAVORITE No avai lable

BACK No available

REC No available

TIMESHIFT No available

HELP No available

TEXT No available

MIX No available

SUBCODE No available

HOLD No available

PIP No available

SWAP No available

MOVE No available



11/319

Connection and preparation of the TV set

Mounting the seat

Take the TV set and its seat out of the carton, and assemble them with

the screws in the accessory box as shown in the following diagram:

1. Put the TV set on the soft cloth or cushion on the desktop with the

face downwards.Place the seat on a secure plane surface.

2. Insert the seat into the clipgroove on the bottom of the TV set.

3. Attach the screws into the seat and screw them down.



12/3110

Backboard singal source interfaces

There are a lot of signal sources that can be connected to your TV set. Thefollowing diagram shows how to connect them.

Friendly tips:

If you want to hang the TV set on a wall, all connecting lines must be inserted

into the ports of the TV set in advance.Whenever a peripheral equipment is connected to the TV set, be sure the TVset is powered off.

While connecting peripheral equipment, connect the cable to the terminal withthe same color as its own.

HDMI 2

COMPONENT

HDMI 1

AUDIO

IN

PC IN

Y Pb Pr L L

AV OUT

VIDEO

VIDEO

AV IN 1

L

R

R

R

TV

ANTENNA

Antenna input:

Insert the antenna terminal into the TV set's antenna socket. This socket is a75 coaxial cable input.

AV IN 1 input:

Connect the VIDEO outputs of DVD player, LCD player, video recorder orvideo camera, etc. to the VIDEO input of the TV set.

Audio input: Connect the audio signal source (PC, DVD player, LCD player,video recorder or video camera, etc.) to the audio input port.

AV output :

This interface can be used to output the TV signal of the unit to another TVset.

Component input:

Connect the audio / video of the component signal source (PC, DVD player,

LCD player, video recorder or video camera, etc.) to the component signalinput port.

PC signal and PC audio input:

Connect the PC signal line to the PC and the PC interface of the TV set.

Connect the audio line to the PC audio input interface of a PC or a TV set.

HDMI:

It refers to "high denitiion multimedia interface". It connects the HDMI signalconnecting line to DVD player, etc.



13/3111

Side signal source interfaces

VIDEOLR

AV IN 2

USB

HDMI 3

Earphone socket:

The user may use the earphone via the earphone socket.

AV IN 2input:

Connect the VIDEO outputs of DVD player, LCD player, video

recorder or video camera, etc. to the VIDEO input of the TV set.

Audio input:

Connect the audio signal source (PC, DVD player, LCD player,

video recorder or video camera, etc.) to the audio input port.



14/3112

Preset and watch TV

The following is how to use the On/Off key ( ) on the TV remote control to turn on/off the TV set. (Press the key Channel +/- in standby mode may power on the unit,its the same for the side panel and the remote control.

Power On/Off

1. While switching on the AC power supply, the red indicator lamp stands for standbymode, while no indicator lamp stands for power on and switch off.

2. If the TV set is in standby mode, press the On/Off key on the remote control topower on.

3. Pressing on the On/Off key on the remote control may enter standby mode again.

4. If you don't use the TV set for a long period, unplug the power cord of the TV setfrom the socket to save electric energy, because the TV set consumes electricityeven in standby mode.

Selecting input signal for TV programIf the TV set is not in the TV mode, the following methods may be used to select TVprogram:

1. Press source key on the remotecontrol to pop out signal source menuon the TV screen (as shown in the rightdiagram).

Press the / key and SOURCE key toselect the option TV, and then press >key or OK key to conrm switching to TVinput terminal. After such switching, thesignal source selection menu disappears,and the information on the current signalsource is displayed on the up right corner

of the screen. If no other operationsare made, the signal source menu willdisappear in nearly 5 seconds.

2. Pressing the CH/V key or number key may also return toTV mode.

How to select TV programSelecting TV program1. Selecting with number key directly

Press the number key directly to select the desired numberof channel.

2. Selecting with the CH/V key Press CH key to select the channel number in the

increasing direction.

Press CHV key to select the channel number in thedecreasing direction.

Selecting TV volumePress the VOL+/- key to adjust to the desired volume.

?

SCAN

F RE EZ E P .M OD E S . MO DE A RC

H.LOCK

SOURCE

OK

DISPLAY

USB BACK

REC

REV FWD PREV NEXT

TEXT MIX SUBCODE HOLD

PIP SWAP MOVE ZOOM

TIMESHIFT PLAY/PAUSE HELP

INDEX

SLEEP FAVORITE

HDMI

/



15/3113

Menu operation

TO USE THE MENU

1. Press the Menu key to display the main menu.

2.

3. Press (right) or OK key to enter the sub-menu, to start or adjust the

selected function item.4. Press Menu button to return to previous menu or to exit.

5.

Picture: Adjust picture parameter setting.

Audio: Adjust audio parameter setting.

Features: Set different functions, timerTV-locketc.

Installation: Setting OSD language, channel search, TV reset to factory

setting, etc.

Use / key to select the function item that needs to be adjusted.

Press (left) key to return to previous menu.

Source Menu

1. Press Source key to display Source Menu, and re-press the button

to change input source.

2.

3. Press (right) or OK key for entry.

Press / (up/down) key to select input source.



16/3114

PICTURE MENU

1. Auto Picture: Select smart picture modes, if you select modes except personal mode,

the preset value will apply to those items: Contrast, brightness, colour, tint, sharpness,

noise reduction, Color Temp, dynamic contrast, dynamic backlight, color enhancement, etc.

2. Contrast: Adjust black and white level for

picture, for suitable contrast makes

picture clear and bright.3. Brightness: Video brightness adjustment,

usually used together with contrast.

4. Colour: Video color saturation adjustment.

5. Tint: Video tint adjustment.

6. Sharpness: Video sharpness adjustment.

Auto picture

Contrast

Brightness

Colour

Sharpness

Noise reduction

Color Temp Normal

Personal

100

100

50

4

Medium

Move Select Exit

Picture

7. Noise reduction: Video noise signal reduction.

8. Color Temp: Provide different color temperature modes.

9. (Advanced Pic): Adjust picture appearance to the best contrast, color and sharpness

through digital method.

Dynamic contrast: Auto-enhance video contrast.

Dynamic backlight: Adjust backlight to get the best visual effect according to

brightness.

Colour enhancement: Make color much brighter and clearer in detail.

10. Picture format: Switch the picture proportion.

Notes: 1. Some picture settings would not be available or some items would show

differently due to different signal.

2. When the source is HDMI, there would be a item named PC MODE in

Picture page, and the HDMI picture mode could be selected throught the item.



17/3115

AUDIO MENU

1. Auto sound: Select audio mode. If you select modes except

personal mode, the preset value will apply to those items:

bass, treble, surround, auto volume, etc.

2. Bass : Bass tone adjustment.

3. Treble : Treble tone adjustment.

4. Volume : Audio volume adjustment.5. Balance: Adjust audio balance of speakers.

6. (Dual I/II) : Select Dual I or Dual II.

7. (Mono/Stereo)Select mono or stereo.

8. Surround : Turn on/off Surround.

9. Headphone volume : Headphone volume adjustment.

10. Auto volume : Adjust volume automatically.

11. Delta volume : Balance volume differentia between channels.

Notes : Some audio settings would not be available due to

different signal.

FEATURE MENU

1. Sleep timer : TV sleep timer setting. If you

set sleep timer to be 0 minutes,

the sleep timer is off.2. TV Time :

After you press TV Time into

sub-menu, press / / / key

and then press OKkey to confirm.

Display current time:

Press Menukey to exit main menu and press OK key;

Select TV Time and press OK or key, and current TV

time will show on top right corner of the screen.

3. On Timer :You can turn on TV and switch to appointed channel from standby

mode automatically at the appointed time with setting on timer.

Activate: Set Daily, Once, Off and other items.While select Off, you

can turn off On timer, and now only activate item is available.

Please set TV Time before you activate On timer.

Time: Set timing time.

Channel No.: Set input source or channel for timing switch.

4. TV Lock : Lock or unlock all channels and devices. After entering TV lock sub-menu,

press / key to select lock or unlock and press OK key.

5. Set code : Set or modify password. Before entering TV Lock sub-menu, user has to key

in the password first (the default password is: 8888) or to set a new password.

If the password is valid, a new dialog box will guide you to finish the operation.

Notes : TV Lock will work only when you restart TV.

and number key to input time

Auto sound

Bass

Treble

Volume

Balance

Surround

Headphone volume

Standard

0

0

1

0

Off

30

Move Select Exit

Audio

Sleep timer

TV Time

On timer

TV lock

Set code

0

Activate

Unlock

Move Select Exit

Features



18/31


19/3117

VGA MENU

(The following settings only apply to VGA mode.)

3. Channel Swap:

Channel exchange action.

Factory settings: To restore factory settings of TV.

1. PIP: Turn on/off PIP.2. PIP Source: Choose video source for PIP.

3. PIP Sound: Choose sound source for PIP.

4. Phase: Adjust signal phase.

5. PC Clock: Adjust signal clock .

6. Auto Adjust: Adjust the signal settings automatically.

7. Reset: Reset part of computer settings.

Notes: Some items are only available for TV in signal

condition. PIP are also available when HDMI input DVI

signal.

Channel number: Use together with Store new channel to preset the serial number of

the new channel.

Fine-tune:Use to change the channels frequency.

Operation steps as follows:

Press or OK to enter fine-tune sub-menu.

Press / to adjust frequency, and press OK key to confirm.

Press / to select store current channel or store new channel.

Press OK key to pop-up new menu, and press / key to decide whether to

store the channel or not.

Store current channel: Store the current modification to current channel.

Store new channel: Store the current modification to current channel and store it in the

definite channel.

Menu, then press / key to decide whether to skip current channel or

not. When one channel is skipped, this channel will not be available by

pressing remote control CH / key but could be available by pressing

relevant number.

Skip channel: Press / key to select, and press OK" or key to enter skip channel

Current Channel: TV current channel, and the channel can be switched.

Target Channel: Channel to be exchanged, and the channel can be switched.

Swap

7.6. Local updates: Use to update software.

.hctiwsdnanoitisops''lebal-EteS.pohsotseilppaylnO

4. Preferences:

Location: Optimize TV Settings to fit your location: H me or Shop.

Volume bar: Hide or show volume bar when volume adjusting.

E-label '

5. Current software: Shows software version.

VGA setting in Picture menu:

1. H.Position: Picture horizontal position adjustment.

2. V.Position: Picture vertical position adjustment.

VGA setting in Features menu:

o

Contrast

Brightness

Color Temp

Picture format

H.Position

V.Position

40

100

Warm

Wide screen

-50

-50

Move Select Exit

Picture

PIP

PIP Source TV

PIP Sound

Sleep timer

TV Time

Off

VGA

0

Move Select Exit

Features

On timer Activate

TV lock Unlock



20/3118

Multimedia feature setting (USB)

You could get music, picture, and video document from USB

devices through the TV. Operation steps as follows:

1. Press Source key.

2. Choose USB to show multimedia menu.

3. Press / key to choose USB devices.

4. Press / key to choose browse way.

5. After entering menu, press / key to select music/ picture/ video page.

6.

Remarks:

1. USB interface of digital multimedia player is not all-purpose. So when some USB devices could

not be recognized, the problem is always not the model malfunction but due to device driver.

2. Because USB devices and memory capability are different, the time needs for multimedia player

to read information are also different. So the information reading speed of the player temporarily

getting slow are not the model malfunction.

3. The voltage supplied to USB interface is 5V, and the most electrical current is 500mA. When some

interface criteria of USB devices are different from standard USB protocol, digital multimedia player

may be unable to recognize USB devices correctly, which is normal.

4. USB could be used as an interface to update software.

5. If some files source could not play because of the parameter decoding-limited problem, the problem is not the model malfunction.

6. The system only applies to memory medium with FAT32 format.

Press / / / key to select target file and press OK to play.

Choose USB Stick

None

File BrowseCategory Browse



21/3119

Establish and use the channel favorite list

You could establish your favorite TV channel and broadcasting station list, so

that you could find these channels easily.

Notes:

You are able to establish and store at most four favorite lists.

Choose favorite list

Add channel to Favorite list

1. While watching TV, switch to the channel you

would like to add to favorite list.

2. Press OK to show channel option menu.

3. Press / key to select Mark as favorite .

4. Press OK or key to show favorite list.

5. Press / to select favorite list you would like

to add new channel.

6. Press OK key to finally add channel to the

favorite list.

Move channel from favorite listNotes: Please select favorite list of the channel before

you move the channel away.

In addition, in channel option menu, Rename channel has the function

to rename the current channel; Lock channel has the function to lock

the current channel.

1. While watching TV, press OK to show channel option menu;

2. Press OK to choose Show favorite ch. and you will find favorite list;

3. Press / key to select favorite list;

4. Press OK to show favorite channel in the list.

1. While watching TV, press OK key to show channel option menu.

2. Press OK to choose Show favorite ch.

3. Press / key to select favorite list and press OK for entry.

4. Press / key to select the channel you would like to move the

channel away from the list.

5. Press OK to choose.

6. Press OK again to show channel option menu.7. Press / key to choose Unmark as fav.

Favorites 2

Favorites 3

Favorites 4

Favorites 1

Mark as favourite

Rename channel

Lock channel

TV Time

Show favorite ch.

Mark as favourite

Rename channel

Lock channel

TV Time

Show favorite ch.

Mark as favourite

Unmark as fav.

Rename channel

Lock channel

TV Time

Show favorite ch.



22/3120

Symptoms Items to Check and Actions to follow

Ghost or double

images

Using a highly directional antenna may improve the picture.

No power

and turn on the television again.

No picture

No picture and power

switched on

clearance around the vent s of the device to be certain there are no blocking walls or

cabinets which would limit the air ow.

Picture position

adjustment

will need to be adjusted.

No photo, music orvideo play or in poor

quality only

No sound

operation and does not indicate a malfunction.

Good sound but poor

color or no picture

Snowish picture andnoise

Television not

responding to

remote control

Control of accessory

devices

PC modes do not

work

Standby

After improper

shutdown TV again will take a longer time than usual.

Miscellaneous See Extras, Specifications on this user manual.

Most High Definition receiver boxes also have picture-positioning controls in their menu systems. If the

TV cursor controls run out of range before the picture is correctly positioned, the receiver box controls

within a radius of approximately four feet.

replace the batteries of the remote control of other devices. E.g. keep away a wireless headphone from

If your TV has been shutdown in an improper way (e.g. power drop, power cord plug out), starting up the

Your TV consumes energy less than 1w in the standby mode.

Troubleshooting



23/3121

Glossary

Aspect Ratio The ratio between the width and height of the TV picture on the screen. In a normal TV set the aspect

ratio is 4 to 3 (4:3). The new aspect ratio in HDTV is 16:9 which resembles the aspect ratio in a movie

theatre (Widescreen). New TV systems support both 4:3 and 16:9 aspect ratio and can automatically

switch between them.

Audio Video (A/V) A term often used when discussing a channel on a TV receiver or on video equipment, which has been

especially designed to accept VCR audio-video signals. This channel automatically activates special cir-

cuitry within the TV set to prevent picture distort ion and skewing. It is also used for audio-video proces-sors, which handle both types of signals.

CVBS Composi te Video Baseband S igna l. In broadcast te levi sion th is re fers to the v ideo signal , inc luding the

colour information and syncs.

Component Video

Input (Y Pb Pr)

Component Video Input is a type of connection that uses a cinch-type connector to allow set top boxes

or analog DVD players to connect a signal to the TV. By offering the cinch-type input (YPbPr) the pri-

mary colors, red, green and blue are connected from a set top box directly into the TV allowing for the

signal to display on the screen.

HDTV

resolution of todays NTSC TV, which essentially makes the picture twice as sharp. HDTV also has a

screen ratio of 16:9 as compared with most of todays TV screens, which have a screen ratio of 4:3.

HDTV offers reduced motion artifacts (i.e. ghosting, dot crawl).

Progressive Scan In Progressive Scanning all the horizontal scan lines are scanned on to the screen at one time. The HDTVStandards accept both Interlaced Scan and Progressive Scan broadcast and display methods.

Resolution

may be expressed as number of pixels in an image; or more commonly, As total number of (horizontally

scanned) Lines used to create the image.

Standard Digital TV Resolutions:

SDTV: 576i - The picture is 720x576 pixels, 576p - The picture is 720x576 pixels.

HDTV: 720p - The picture is 1280x720 pixels, 1080 i/p - The picture is 1920x1080 pixels,

The generally agreed upon de finition of HDTV is approximately twice the vertical and horizontal picture

Resolution: A measurement of the finest (smallest) detail that is visible in a video image. TV Resolutions

(AV Video)



24/3122

WARNINGconcerning stationary images on the TV

of the LCD panel. Normal use of the TV should involve viewing of programs that have constantly moving

or changing images. Do not leave moving images on screen for extended periods of time. Do not display

the same images too frequently; if you do, subtle ghost images can be left on the LCD screen. Sources of

stationary images may be Laser discs, video games, Compact Discs Interactive (CD-i), paused Digital VideoDiscs (DVDs) or video tapes.

Here are some common examples of stationary images:

movie is viewed on a TV with standard (4:3) aspect ratio. This occurs with some DVDs.

graphics are less likely to damage the picture tube.

news.

These usually appear in the same location on the TV screen.

TV Location

the TV where temperatures can become excessively hot -- for example, in direct sunlight or near a

heating appliance.

Cleaning

or using anything abrasive. Do not use household cleaners. Wipe the screen with a clean cloth dampened

with water. Use even, easy, vertical strokes when cleaning.

blemish the cabinet.

Care And Cleaning

Screen: Do not leave fixed images on the screen for extended periods of time. This can cause uneven aging



25/3123

Product specifcations

FunctionPC input function,Support TV, AV(CVBS),Component(YPbPr), HDMI inputs, USB

input,Earphone Output function.

Item L32F6 L42F6

TV function TV standardColor system: PAL/NTSC/SECAMSound system: B/G, I, D/K, M

Video input

Rear connector

COMPONENTx1

AVx1

HDMIx2

Side connectorHDMIx1

AVx1

Video output Rear connector AVx1

PC input Rear connector PCx1

AUDIO INx1

Audio outputAudio output:L/R

Speaker (built-in): 2 x 10W

For stereo earphone mini socket

Power supply

Power supply 100-240V~, 50-60Hz

Power consumption


26/3124


This unit supports COMPONENT(YPbPr) formats:

SN Signal format Refresh frequency (Hz)

1 480i/480p 602 576i/576p 50

3 720p 50/60

4 1080i 50/60

Input format of supported PC interface:

Number ResolutionRefresh frequency

(Hz)

1 640*480 60

2 640*480 75

3 720*400 70

4 800*600 56

5 800*600 60

6 800*600 72

7 800*600 75

8 1024*768 60

9 1024*768 70

10 1024*768 75

111360*768

(recommended)60

12

1920*1080

(only for L42F6) 60



27/31


Input format of supported HDMI interface:

SN Name of signalRefresh frequency

(Hz)1 480i/480p 60

2 576i/576p 50

3 720p 50/60

4 1080i/1080p 50/60

5 720*400 70

6 640*480 60/75

7 800*600 56/60/72/75

8 1024*768 60/70/75

9 1360*768 60

26loaded from www.Manualslib.commanuals search engine


28/31



29/31



30/31



31/31

Documents

manual de servicio haier l42f6