Upload
sarwar-sayeed
View
2.767
Download
3
Embed Size (px)
Citation preview
AUTOMATIC BRAKING SYSTEM&
PATH FINDER
A MAJOR PROJECTSUBMITTED IN THE FULFILLMENT OF THE REQUIREMENT
FOR THE AWARD OF THE DEGREE OF
BACHELOR OF TECHNOLOGYIN
MECHANICAL ENGINEERINGOF
KURUKSHETRA UNIVERSITY, KURUKSHETRA
BY NAVNEET KUMAR (1504284) NARENDER KUMAR (1504285)
HAPPY YADAV (1504286)
UNDER THE GUIDANCE OF Mr. SACHIN WADHWA
DEPARTMENT OF MECHANICAL ENGINEERINGN.C. COLLEGE OF ENGINEERING
ISRANA (PANIPAT)JUNE 2008
ACKNOWLEDGEMENT
To execute a project honestly is the cherished desire of any would be
engineer and to do this we are no exception that we have managed to achieve
this at all.
We thank the INKOTECH Pvt. Ltd for helping in the Research Experiences for
Undergraduates (REU) program and providing this educational opportunity.
We also thank Mr. SACHIN WADHWA for his guidance & helping us in all the
possible ways. We express our sincere thanks towards our guide for his
unstinted support & commitment to make our project see light of today and
the college for use of their facilities.
CERTIFICATE
This is to certify that the dissertation report entitled “AUTOMATIC BRAKING AND PATH FINDER” being submitted by: -
a) NAVNEET KUMAR (1504284)
b) NARENDER KUMAR (1504285)
c) HAPPY YADAV (1504286)
In fulfillment for the award of degree of bachelor in technology in
Mechanical Engineering at the department of Mechanical Engineering,
NEMI CHAND COLLEGE Of ENGG.ISRANA is a record of students own work
carried by them under my supervision & guidance.
MR. SACHIN WADWA
(Sr.lecturare)
Mechanical Deptt.
CHAPTER 1: INTRODUCTION
To find auto break when enter accident area by proximity system when
the two disciplines (Mechanical &Electronic) are brought together, a whole
new world of interesting possibilities opens up. Here is a very simple and
useful circuit for security purposes.
Any vehicle when entered without break in proximity area become
safe, one can seek the help of security proximity system. The project has two
main parts an intruder sensor cum transmitter and a receiver.
IR transmitter and receiver pair can be used to realize a proximity
detector. The circuit presented here enables you to detect any object capable
of reflecting the IR beam and moving in front of the IR LED photo detector pair
up to a distance of about 5 meter from it.
Here is a illustrative project, where a simple hardware circuit is directly
interfaced to other vehicle. It can object counter for an assembly line
conveyer belt, and so on. With a little modification of the hardware.
Braking system of vehicles:-
The hybrid vehicle brake system includes both standard hydraulic brakes
during this phase of braking; the hydraulic brakes are not used. When more
rapid deceleration is required, the
hydraulic brakes are activated to provide additional stopping power.
The sensors can become contaminated with metallic dust and fail to detect
wheel slip; this is not always picked up by the internal ABS controller
diagnostic.
Here, two more sensors are added to help the system work: these are a wheel
angle sensor, and a gyroscopic sensor. The theory of operation is simple:
when the gyroscopic sensor detects that the direction taken by the car doesn't
agree with what the wheel sensor says, the ESC software will brake the
necessary wheel(s) (up to three with the most sophisticated systems) so that
the car goes the way the driver intends. The wheel sensor also helps in the
operation of CBC, since this will tell the ABS that wheels on the outside of the
curve should brake more than wheels on the inside, and by how much.
Typical System (No ABS):-
Typical Layout of System (with ABS) :-Typical System (ABS):-
Components:-Components:-
Sliding Caliper
Fixed Caliper
Pressure Control Valves
HARDWARE DESCRIPTION
The transmitter part consists of two 555 timers (IC1, IC2 for driving an
infrared LED. the infrared detector to sense the transmission; To save power,
the duty cycle of the 38kHz a stable multi vibrator is maintained at 10 per
cent.
The receiver part have an infrared detector comprising (IC3, IC4, IC5,
IC7 ) wired for operation and timer, followed by (T1) & (T2) transistor. Upon
reception of infrared signals to pin-2 of IC-4, the 555 (IC4) timer (mono) is
turned ‘on’ and it remain ‘on’ as long as the infrared signals are being
received.
Effectiveness
A 2003 Australian study by Monash University Accident Research Centre found
that ABS:
Reduced the risk of multiple vehicle crashes by 78 percent.
Reduced the risk of run-off-road crashes by 35 percent.
On high-traction surfaces such as bitumen, or concrete many ABS-equipped
cars are able to attain braking distances better (i.e. shorter) than those that
would be easily possible without the benefit of ABS. Even an alert, skilled
driver without ABS would find it difficult, even through the use of techniques
like threshold braking, to match or improve on the performance of a typical
driver with an ABS-equipped vehicle, in real world conditions. ABS reduces
chances of crashing, and/or the severity of impact. The recommended
technique for non-expert drivers in an ABS-equipped car, in a typical full-
braking emergency, is to press the brake pedal as firmly as possible and,
where appropriate, to steer around obstructions. In such situations, ABS will
significantly reduce the chances of a skid and subsequent loss of control.
In gravel and deep snow, ABS tends to increase braking distances. On these
surfaces, locked wheels dig in and stop the vehicle more quickly. ABS
prevents this from occurring. Some ABS calibrations reduce this problem by
slowing the cycling time, thus letting the wheels repeatedly briefly lock and
unlock. The primary benefit of ABS on such surfaces is to increase the ability
of the driver to maintain control of the car rather than go into a skid — though
loss of control remains more likely on soft surfaces like gravel or slippery
surfaces like snow or ice. On a very slippery surface such as sheet ice or
gravel it is possible to lock multiple wheels at once, and this can defeat ABS
(which relies on detecting individual wheels skidding). Availability of ABS
relieves most drivers from learning threshold braking.
When drivers do encounter an emergency that causes them to brake hard and
thus encounter this pulsing for the first time, many are believed to reduce
pedal pressure and thus lengthen braking distances, contributing to a higher
level of accidents than the superior emergency stopping capabilities of ABS
would otherwise promise. Some manufacturers have therefore implemented
Mercedes-Benz's "brake assist" system that determines that the driver is
attempting a "panic stop" and the system automatically increases braking
force where not enough pressure is applied. Nevertheless, ABS significantly
improves safety and control for drivers in most on-road situations
The ABS equipment may also be used to implement traction control on
acceleration of the vehicle. If, when accelerating, the tire loses traction with
the ground, the ABS controller can detect the situation and take suitable
action so that traction is regained. Manufacturers often offer this as a
separately priced option even though the infrastructure is largely shared with
ABS. More sophisticated versions of this can also control throttle levels and
brakes simultaneously.
Design and selection of components
Given the required reliability it is illustrative to see the choices made in the
design of the ABS system. Proper functioning of the ABS system is considered
of the utmost importance, for safeguarding both the passengers and people
outside of the car. The system is therefore built with some redundancy, and is
designed to monitor its own working and report failures. The entire ABS
system is considered to be a hard real-time system, while the subsystem that
controls the self-diagnosis is considered soft real-time. As stated above, the
general working of the ABS system consists of an electronic unit, also known
as ECU (electronic control unit), which collects data from the sensors and
drives the hydraulic control unit, or HCU, mainly consisting of the valves that
regulate the braking pressure for the wheels.
How Automatic-Braking System Work
The communication between the ECU and the sensors must happen quickly
and at real time. A possible solution is the use of the CAN bus system, which
has been and is still in use in many ABS systems today (in fact, this CAN
standard was developed by Robert Bosch GmbH, for connecting electronic
control units!). This allows for an easy combination of multiple signals into one
signal, which can be sent to the ECU. The communication with the valves of
the HCU is usually not done this way. The ECU and the HCU are generally very
close together. The valves, usually solenoid valves, are controlled directly by
the ECU. To drive the valves based on signals from the ECU, some circuitry
and amplifiers are needed (which would also have been the case if the CAN-
bus was used).
The sensors measure the position of the tires, and are generally placed on the
wheel-axis. The sensor should be robust and maintenance free, not to
endanger its proper working, for example an inductive sensor. These position
measurements are then processed by the ECU to calculate the wheel-spin.
The hydraulic control unit is generally located right next to the ECU (or the
other way around), and consists of a number of valves that control the
pressure in the braking circuits. All these valves are placed closely together
and packed in a solid block. This makes for a very simple layout, and is thus
very robust.
The central control unit generally consists of two microcontrollers, both active
simultaneously, to add some redundancy to the system. These two
microcontrollers interact, and check each other's proper working. These
microcontrollers are also chosen to be power-efficient, to avoid heating of the
controller which would reduce durability. The software that runs in the ECU
has a number of functions. Most notably, the algorithms that drive the HCU as
a function of the inputs, or control the brakes depending on the recorded
wheel spin. This is the obvious main task of the entire ABS-system. Apart from
this, the software also needs to process the incoming information, e.g. the
signals from the sensors. There is also some software that constantly tests
each component of the ABS system for its proper working. Some software for
interfacing with an external source to run a complete diagnosis is also added.
As mentioned before the ABS system is considered hard real-time. The control
algorithms, and the signal processing software, certainly fall in this category,
and get a higher priority than the diagnosis and the testing software. The
requirement for the system to be hard real-time can therefore be reduced to
stating that the software should be hard real-time. The required calculations
to drive the HCU have to be done in time. Choosing a microcontroller that can
operate fast enough is therefore the key, preferably with a large margin. The
system is then limited by the dynamic ability of the valves and the
communication, the latter being noticeably faster. The control system is thus
comfortably fast enough, and is limited by the valves.
Parts of automatic braking system:-
There are four main components to an ABS system:
Speed sensors
Pump
Valves
Controller
Speed Sensors
The braking system needs some way of knowing when a wheel is about to lock
up. The speed sensors, which are located at each wheel, or in some cases in
the differential, provide this information
Valves
There is a valve in the brake line of each brake controlled by the ABS. On
some systems, the valve has three positions:
In position one, the valve is open; pressure from the master cylinder is
passed right through to the brake.
In position two, the valve blocks the line, isolating that brake from the
master cylinder. This prevents the pressure from rising further should
the driver push the brake pedal harder.
In position three, the valve releases some of the pressure from the brake.
Pump
Since the valve is able to release pressure from the brakes, there has to be
some way to put that pressure back. That is what the pump does; when a
valve reduces the pressure in a line, the pump is there to get the pressure
back up.
Controller
The controller is a computer in the car. It watches the speed sensors and
controls the valves.
methodology for the interpretation of sensor data, route planning,
and vehicle control
Radar Signal processing software provided with the Epsilon Lambda Electronics
ELSC71-1A 3D radar will produce a data map of the field of view with the
range, azimuth, elevation, velocity, and signal amplitude for each object
detected. The azimuth is known as a function of time because the radar
antenna is mechanically scanned across the field of view by a stepper motor.
The range
is found from a beat signal with amplitude. The velocity is found by Doppler
frequency, and the elevation angle is found by taking the phase difference
between two IF channels. Range resolution is approximately 1 meter, azimuth
resolution is 1.8 degrees, and elevation resolution is about 1 degree.
We will interpret abrupt changes of elevation as obstacles for the vehicle to
avoid. Targets which seem to be moving relative to most of the field of view
will be interpreted as moving obstacles, probably other Challenge Vehicles,
and given an especially wide berth. We may be able to use the amplitude of a
signal return to further classify objects (e.g., a stronger return would be
expected from a metal vehicle than from a desert plant).
Vision The vision system will consist of several video cameras, each rigidly mounted
to the vehicle. We will know the rigid transformations describing the position
and orientation of each camera and the radar system with respect to the
vehicle coordinate system and the other cameras, at every instant of time. We
also know the internal parameters of each camera, which can be obtained
using standard rig calibration techniques [Bouguet].
In this case, a point in space, X, projects onto each camera. Most points will be attached to the same rigid surface, the terrain. Some will be on opposing vehicles, which can be modeled as separate rigid bodies moving in an independent manner. Still other points in space will belong to miscellaneous objects which may or may not be rigid, such as birds or clouds. For objects within the range and field of view of the radar, the vision system will know the approximate depth and velocity of locations in space. This greatly simplifies various vision tasks, since the relative change in pose between two instants of time is known. This provides a great deal of information for tasks such as feature tracking, motion estimation/segmentation, and geometric reconstruction. Objects beyond radar range will also need to be detected, tracked, and potentially identified, but since geometric information may not be easily obtained, we will use image-based techniques, such as
color segmentation and 2D recognition. We will also investigate the efficacy of more advanced Level Set tracking methods [Cremers]. Detection of Other Challenge Vehicles The initial detection of a potential vehicle will occur in both the vision and radar systems. The radar will indicate the presence of an obstructing object in its depth map, assuming the object falls within the field and depth of view. Simultaneously, the vision system will detect the presence of one or more lights of the specified alert-light color in an invariant color space (such as HSV). When this occurs, the car-detection software module will attempt to find periodic flashing, which will positively indicate the presence of an opposing vehicle. The other vehicle’s position in space can be updated by tracking the image-plane coordinates of its lights and other areas-of-interest on the image of the vehicle, as well as by using radar data if any.
Detection of Miscellaneous Objects The radar system should detect most medium and large positive obstacles in
its field of view. We rely on the vision system to detect negative obstacles,
positive obstacles which are significant but too small for the radar to resolve,
and obstacles which are outside of the radar’s field of view or which could not
be seen until they were inside the radar’s minimum range.
In the environment we will be traveling through, there are many regions of the
image with very regular appearances. Rocky and sandy surfaces will present a
difficult problem for image feature
tracking due to the similarity of appearance of many nearby areas in the
images. Hence, traditional structure-from-motion schemes will likely fail for
the task of detecting dangerous objects. Luckily, we can exploit other
information about the structure of the environment and a priori knowledge.
Since the system will know the time of day, its orientation, and the lighting
conditions, it can employ a shape-from-shading and shape-from-shadow
system to determine the approximate position and dimensions of obstacles
like large rocks or craters.
Classification of Terrain Understanding of the type of surface on which the vehicle is traveling is
essential for determining a safe speed and control technique. Paved roads or
dry lakebeds will allow aggressive control at high speed, while rocky or
uneven terrain must be traversed with more care. The radar system might
provide some information regarding the terrain type from the amplitude of the
signal return, but generally we expect better data from the vision system. Our
terrain classification system will use Bayesian sensor fusion techniques,
whereby the signals from the cameras and the radar are jointly interpreted to
provide an estimate of the terrain type in the field of view. A statistical model
will be trained using recorded data from the cameras and radar, and the
parameters of the Bayesian network will be learned in a supervised manner.
Other inputs to the model will be time of day and weather, both of which will
influence the lighting conditions of the environment.
Determination of Local Road Geometry While the GPS system and maps will provide medium and long-range path
planning goals (waypoints), knowledge of the local upcoming road geometry
can only be determined by on-board sensing. This information is crucial for
short-range control and path generation. In particular, the control system will
need to know the boundaries of the beaten trail, which will provide the safest
route through the terrain in the absence of other obstacles. Determining these
boundaries will be difficult due to the similarity of appearance of most parts of
the images. From initial experiments with off-road trail video, we have
determined that a distinguishable characteristic of the path is its relatively low
spatial frequency. In general, a beaten path will be smoother since it will have
fewer jagged rocks, little or no vegetation, and a somewhat consistent
material.
Route Planning After the Route Definition Data File is provided, a nominal minimum-cost route
from each waypoint to the next will be computed based on map data using a
wavefront-propagation path planner. The output of this planner will be
nominal desired headings and target speed as a piecewise-polynomial
function of latitude and longitude across the permitted corridor between and
around each waypoint pair, and this information will be stored for
consideration at the appropriate point in the Route.
At all times after the vehicle passes the Departure Line, it should have an
estimate of its current location and heading, and nominal desired headings
version of the wavefront-propagation path planner to find the optimal
obstacle-free trajectory that will take it to a point on the sensor horizon with
as close as possible to the precomputed nominal desired heading and speed.
This second algorithm will be adapted to the local planning problem in that it
will more finely differentiate (x,y,theta) space and take more account of the
vehicle kinematics and dynamics (e.g., steering linkage position, turning
radius as a function of speed).
If there is no unobstructed path to the nominal computed route within the
vehicle’s field of view, the vehicle will slow down, in anticipation that the route
might be blocked and it might be about to receive an E-Stop signal. If space
permits, the vehicle will turn to shift its field of view and possibly find another
route. If the vehicle can neither turn nor progress forward, it will come to a
stop and wait for an E-Stop, or for the route to clear.
In any case, at each instant the planner should provide a desired speed and
heading. PID control loops for the steering and accelerator/brake will then
attempt to correct the current speed and heading. The planner is responsible
for providing the PID controller with a “desired” trajectory that is within the
limits of the actuators and the vehicle dynamics, e.g. the planner should not
demand a turn which is unsafe at either the current or desired speeds.
CHAPTER 2: LITERATURE REVIEW
Though lot of literature survey has been done for this work. Problem was the
industry generated and for its solution a thorough literature survey has been
done, from that we find out that there is lot of scope of improvement in
industrial productivity by Work Study techniques. Some of the main papers
are as follows:
Edward C. Francis (1986) explained that Automatic Vehicle Control
Overview
PRT 2000™ operates with a highly responsive control system, custom
developed by Raytheon to provide reliable and safe transit of passengers,
delivering maximum system capacity by operating with a minimum distance
between vehicles. This Automatic Vehicle Control (AVC) system has been
developed based on the principles common to all Automatic Train Control
(ATC) systems, following the new American Society of Civil Engineers (ASCE)
Automatic People Mover (APM) standards, and specific requirements unique to
this application. PRT 2000™ response times are fractions of a second, allowing
vehicles to operate at headways as short as 2.5 seconds at 30 mph. Vehicle
motion is continuously monitored and adjusted in real time to safely and
efficiently merge streams of traffic where guideway sections join, and to
properly switch vehicles toward their destination where a single guideway
section diverges into two. Empty vehicles are automatically routed to stations
where passenger demand exists.
PRT2000's™ AVC system is constructed in a three-level hierarchy. Every
vehicle carries an on-board controller. These vehicle controllers receive
direction from and report status to stationary wayside controllers, responsible
for coordinating vehicle activities within fixed regions of the guideway. An RF
data link mounted within the guideway structure allows continuous, high-
bandwidth communications between the vehicle and wayside. The following
figures depict a typical alignment and the partitioning of the control function
to the distributed waysides.
The wayside controllers are connected to each other via a high-speed fiber-
optic network to coordinate vehicles transitioning from one region of guideway
to the next. The fiber network extends to a central System Control Center
(SCC), providing the System Control Operators with comprehensive status and
oversight of the system's behavior. Within this modular, three-level computing
hierarchy, PRT 2000's™ AVC system provides the functions required for the
safe, automated control of vehicles. Automatic Vehicle Protection (AVP),
Automatic Vehicle Operation (AVO) and Automatic Vehicle Supervision (AVS)
functions are provided, in accordance with ASCE standards.
Automatic Vehicle Protection
AVP protects passengers, personnel and equipment from potentially
hazardous situations; it has precedence over AVO and AVS functions. By
reliably monitoring vehicle movement and equipment status within the
system, AVP is able to revert the system to a safe state whenever a
potentially hazardous condition is detected.
AVP autonomously monitors the position and speed of each vehicle, the state
of its doors and door locks, and the state of its in-vehicle switch. The AVP
system is based on a principle of permissive action; no action is permitted
unless AVP can ensure it is safe. Continuous, positive action by AVP is required
to allow vehicles to proceed along the guideway. As shown in the inset, a
complete set of AVP functions is provided.
All processing associated with AVP is performed in parallel by a pair of
redundant safety processors which are cross-checked for agreement. This
agreement is a condition for any vehicle motion. A fail-safe hardware
watchdog module on each vehicle keeps propulsion disabled and emergency
braking engaged unless it receives periodic indication that its processors are
operating correctly and the suite of safety checks they perform are all
satisfied. In addition, the watchdog must receive regular assurance that
communications with the wayside controller is functioning properly. In the
wayside controller, a similar fail-safe architecture uses a hardware watchdog
module to inhibit communications with vehicles unless it receives periodic
indication that its safety processors are operating correctly and that their
safety checks are satisfied.
All devices vital to safety are handled directly by AVP hardware and software.
Safety-critical equipment sensors are triple redundant; a majority voting
scheme provides for safe and reliable operation. AVO access to the door locks,
the in-vehicle switch, and the parking brakes is via request to AVP. AVP
satisfies a request only if it is safe to do so.
Automatic Vehicle Operation
AVO controls vehicles to provide automatic origin to destination passenger
service between all stations in the system. This requires commanding the
propulsion system to move the vehicle along the mainline guideway and
within the stations, operating the in-vehicle switch to pursue a route to the
vehicle's destination, and operating vehicle doors for boarding and
deboarding. Vehicle movement is performed such that system capacity is
maximized while observing all necessary constraints for safety and ride
comfort. In particular, AVO operates the vehicles so that hazard protections
are not invoked within AVP, which serves as the fail-safe monitor for the PRT
2000 control system.
AVO moves vehicles throughout the system in accordance with their
destinations. Each vehicle carries its current destination with it as it travels,
supplying it to the wayside controllers as part of its regularly reported status.
Vehicle destinations change automatically as passenger trips begin and end,
as empty vehicles are distributed, or as vehicles are added to or recalled from
active service. The System Control Operator can also change vehicle
destinations via manual intervention.
AVO controls the route that a vehicle takes to reach its destination by
commanding its in-vehicle switch assembly either left or right each time the
vehicle travels through a diverge region. Routing tables distributed by AVS to
the wayside controllers provide the basis for AVO's positioning of the switch.
PRT 2000's off-line passenger stations allow vehicles to travel directly from
their origin to their destination, bypassing all intermediate stations along the
way. As the vehicle approaches its destination station, AVO manages its
entrance to the station, assigns it a berth and precision aligns it. AVO applies
the parking brake and holds the vehicle at zero speed until passenger
boarding completes, then coordinates the exit of the vehicle from the station
back out onto the mainline.
AVS provides automatic and System Control Operator (SCO) initiated system-
wide monitoring and control capabilities. There are three sets of related
responsibilities.
First, AVS compares system performance against established levels of service
and automatically adjusts or controls the system to meet varying patron
demands. Routing tables are distributed to each of the wayside controllers to
specify the current best path to reach each destination. In most cases, all
vehicles are given the same direction for a given destination, corresponding to
the quickest path. However, in situations where there are multiple paths to
the destination that may be traversed in approximately equal time, the
system may specify that a percentage goes one way and the remaining
percentage goes the other. Empty vehicle management instructions are
specified for each station, based on demand. AVS controls audible and visual
interfaces with patrons throughout the course of their interaction with the
system, and controls the attendant ticket processing to initiate trips.
Second, AVS monitors vehicle traffic and equipment health, maintaining an
active log of vehicle status, trip summary data, faults, and alarms. To the
degree it can, AVS may also initiate certain automated fault recovery
operations in response to unexpected events. For example, if one of the two
redundant traction motors fail, AVS will automatically recall the vehicle from
service after completing the current trip. As part of its system monitoring
responsibility, AVS provides statistical accounting of trips and equipment
usage to support ridership analysis and maintenance activities.
Finally, based on monitored system behavior and performance, AVS provides
information to and accepts controls from the SCO to modify the automatic
operations of the system or manually intervene in extraordinary
circumstances. The SCO's role is primarily one of monitoring stations for
safety and security, and responding to patron requests for assistance. At the
same time, when an abnormal situation arises, AVS provides "human- in-the-
loop" controls for fault management.
AVC Hardware Components
AVC computer and data communications hardware is distributed between the
System Control Center, the wayside and the vehicles, providing the platform
for AVP, AVO, and AVS functions. This hardware operates in conjunction with
resident software and interfaces with other equipment to provide the required
system level performance.
Vehicle Controller
One vehicle controller resides in each vehicle in a dual-redundant
configuration; it is automatically reconfigured to continue to operate through
hardware and software faults. The vehicle controller monitors and controls a
myriad of subsystems in the vehicle, as depicted in the figure below:
Each vehicle controller can sense and drive a vehicle's switches, annunciators,
display, sensors and actuators and other supporting control/communication
equipment by way of resident real-time operating software. The vehicle
controller interfaces to the local wayside controller using its Vehicle
Communications (VCOM) RF communication antennas. Two antennas mount
on the chassis for bi-directional communication via the guideway antenna
located on the left or right side.
The vehicle controller has a dual redundant architecture, containing two
independent Vehicle Control Sets (VCS). Each VCS is an independent
computer with a complete complement of I/O. Only one VCS is active at a
time, with the active VCS controlling actuators and VCOM communication. The
non-active VCS operates in a standby mode, ready to takeover if the active
VCS goes down.
Within a VCS, a cross-checking pair of safety processors provides a safety-
critical computing environment. Each member of the pair communicates with
the other and issues a heartbeat at regular intervals to a watchdog module
only after insuring its own health and that of its partner. If either both VCSs or
the VCOM is deemed unhealthy, the watchdog module will stop the vehicle
using the vehicle's propulsion / brake interlock.
Each vehicle carries a permanent unique code as a Vehicle ID which is
accessible by software. This code is contained in an assembly that is
permanently mounted in the cabin and is separate from the Controller.
Within the vehicle controller there is also a set of non-redundant hardware for
non-safety-critical functions including controlling the vehicle doors and
interfacing to the passengers with a text display and audio board.
Wayside Controller
A wayside controller is configured to communicate to vehicles utilizing up to
four separate communications antennas. Each single antenna spans a
separate region of the guideway. Redundant hardware allows controllers to
operate through single hardware failures. Interfaces to ticketing equipment,
station signs, audio and other building equipment are provided, as depicted in
the following figure.
Eight processors typically reside in a wayside controller. Four of the
processors provide two redundant pairs that manage all the AVO and AVS
functions. An additional four processors are used to provide safety-critical
operations, configured as two cross-checking pairs. Each member of a safety
pair communicates with the other and issues a heartbeat at regular intervals
to a watchdog module only when it considers both itself and its corresponding
processor to be healthy.
The watchdog module monitors the heartbeats from the four safety
processors, and selects one pair to monitor the safe operation of the system.
If, through the absence of heartbeats, the watchdog module determines that
neither processor pair is healthy, the watchdog shuts down the VCOM region
controlled by the wayside controller. The vehicle controller is designed to
ensure that when VCOM messages cease, the vehicle is brought to a stop,
guaranteeing a safe state.
Data Communications
Two distinct data communications services are provided by the PRT 2000™
AVC system. Data exchange between the vehicle controller and wayside
controller is provided by an RF link that affords a non-contact mechanism for
exchange between the moving vehicle and stationary wayside. Wayside to
wayside communication is provided by a fiber-optic link that features the
range and high-speed data rates required to manage the system. This fiber-
optic link is also used by the System Control Center to communicate with all
the waysides.
Timothy A. Springer (1991) examined the initial step in leukocyte
accumulation in inflamed tissue is a rolling interaction on the vessel wall. The
driving force for rolling is the hydrodynamic force of the bloodstream acting on
the adherent cell; rapid formation and breakage of adhesive bonds are
required for the adhesive contact between the leukocyte and the vessel wall
to be maintained and to be translated along the vessel wall during
rolling .Rolling occurs in a series of steps or jerks that appear to represent
receptor-ligand dissociation events From measurements of the dimension of
the adhesive contact zone in the direction of flow and the average step
distance, it has been estimated that as few as two adhesive bonds between
the cell and the substrate are sufficient to support rolling .
The selectin glycoproteins are limited in expression to vascular cells and are
specialized to mediate rolling. L-selectin is expressed on leukocytes and binds
to carbohydrate ligands on endothelium and other leukocytes; E-selection and
P-selectin are expressed on endothelium and bind carbohydrate ligands on
leukocytes. The structures of several of these molecules are known from
crystals or electron micrographs and equilibrium constants, kinetics, and effect
of applied force on kinetics are known for several of the molecular interactions
Rolling should be an inherently unstable transition state, delicately poised
between firm adhesion and lack of adhesion. However, rolling through
selectins is highly stable to alterations in selectin density and hydrodynamic
force acting on the cell this force is proportional to and can be calculated from
the shear stress at the vessel wall. The velocity of rolling cells varies little in
vivo or in vitro despite wide variation in wall shear stress). This stability in the
velocity of rolling leukocytes is likely to be important in the postulated
function of rolling as a checkpoint in the process of leukocyte accumulation in
inflammation. Rolling enables leukocytes to survey endothelium for signs of
inflammation, including chemoattractants that can activate firm adhesion
through integrins, and provide directional cues for transendothelial migration
Particularly in early or in mild inflammation, leukocytes may roll through a
postcapillary venule without developing firm adhesion, and thereby reenter
the circulation . It appears that a threshold level of activation must be
exceeded before firm adhesion is stimulated. Rolling velocity will determine
the time duration of exposure of a leukocyte to activating stimuli on the vessel
wall, and hence should be of key importance in determining whether
activation occurs. Therefore, for proper control of activation of rolling
leukocytes, it may be important for rolling velocity to be relatively
independent of wall shear stress, which varies widely depending on tissue and
physiologic and inflammatory state. Even for different postcapillary venules
within a single tissue, wall shear stress can vary markedly; e.g., it ranges from
3-36 dyn/cm2 for 30-40-µm venules in cat mesentery
Recently, a number of constants critical to an understanding of rolling at the
cellular and molecular level have been measured. Most measurements come
from studies of the dissociation rate constants for "transiently tethered" cells.
Transient tethers occur when leukocytes in a hydrodynamic flow chamber
interact with a substrate, i.e., the lower wall of the flow chamber, that bears
selectins or ligands at densities too low to enable rolling . Under these
conditions, leukocytes moving at the hydrodynamic flow velocity will
momentarily bind to the substrate and remain almost motionless, then
dissociate and resume movement at the hydrodynamic velocity. Transient
tethers have first-order dissociation kinetics and may reflect unimolecular
binding and dissociation events.
Gregson K. (1993) suggested how to judge between competing work-study
projects in order that efforts were wisely and profitably directed. Showed that
factor analysis could be a useful technique to determine which of a number of
possible paths of an investigation were likely to yield the best results.
Described factor analysis by citing a specific example.
CHAPTER 3: WORKING
3.1 PROCESS IN SENSOR
This project was based on photo diodes and photo transistor. Photo diodes
had been used as a transmitter and photo transistor as a receiver. This project
had been divided in two part, First part transmitter section and second part
receiver section.
TRANSMISSION SECTION:- Transmitter module uses IC-555 as a stable
multivibrator operating at a frequency of around 1 KHz with a PNP transistor in
IRED (photo diode) driver stage at the output. This module emits modulated
infrared light. IRED is connected in series for more range and wider directivity.
The module can transmit IR rays up to few meters without use of any external
lens.
FIG. TRANSMISSION COMPONENT
When a vehicle comes nearly person, circuit is energized. The output of IC-555
is square wave from Pin No. 3. T1 gets biasing current to out put of IC-555 and
the IR-LED is connected to T1 collector with R5. The transmit IR beams
modulated at same frequency 1KHz. The oscillator frequency can be shifted
by adjusting preset VR-1. The receiver uses infrared module. The IR- signal
form the transmitter is sensed by the receiver sensor. The same automatically
turns ‘off’, as the person moves away.
RECEIVER SECTION:- Block diagram of the circuit is shown in transmitter
section consists of a power supply, an oscillator, and an output sage, whereas
the receiver section comprises power supply, an infra-red detector module,
time delay circuit, op-amp with noise filter, and an output section. The
complete schematic diagrams of the transmitter and receiver sections are
shown in circuit diagram respectively.
FIG. RECEIVER COMPONENT
This section is divided in a three part, witch pe-amp., amp. and switching
section. The receiver uses infrared modules IR-signal from the transmitter is
sensed by the sensor and its output PIN 1 goes low and switched IC-3. IC-3 is
worked on astable pulse which receives at Pin No. 2. Its output at Pin No 6
troughs high, witch amplifier to weak signals.
The receiver part have an infrared detector comprising (IC3,IC4,IC5,IC7 )
wired for operation in Amp.mode and timer, followed by pnp (T1) & npn (T2)
transistor. Upon reception of infrared signals to pin-2 of IC-4, the 555 (IC4)
timer (mono) is turned ‘on’ and it remain ‘on’ as long as the infrared signals
are being received.
The op-amp are in the set state. Pin 6 of IC-5 are high. The computer reads its
parallel port, to see if pin number 11 is low. Remember, whenever a aeroplane
passes in front of the radar, IC-3 are received input pulse, and pin 6 of IC-3
goes high and IC-4 receives input pin-2 form T2. IC-4 is worked as a power
amp, Pin-3 of IC-4 is A burst output of 38 kHz, modulated at 100 Hz. IC-5
works as a switching, collector of T4 is low , IC-5 take input plus at pin-2 and
output goes at pin-6 (high). As soon as The computer reads its collector of
T5, a software inside the computer starts ticking. After a are checked to see if
the aeroplane has crossed without information to IR beam also. This fact is
displayed on the screen. Pin-2 of PC is high output, The computer is switched
the gun. If, aeroplane is passed signal, second receiver is switched to
proximity system.
The same arrangement can be turned into a burglar alarm by just modifying
the software.
3.2 WORKING PRINCIPLE
Any vehicle when entered without break in proximity area become
safe, one can seek the help of security proximity system. The project has two
main parts an intruder sensor cum transmitter and a receiver.
IR transmitter and receiver pair can be used to realize a proximity
detector. The circuit presented here enables you to detect any object capable
of reflecting the IR beam and moving in front of the IR LED photo detector pair
up to a distance of about 5 meter from it.
Here is a illustrative project, where a simple hardware circuit is directly
interfaced to other vehicle. It can object counter for an assembly line
conveyer belt, and so on. With a little modification of the hardware.
Braking system of vehicles:-
The hybrid vehicle brake system includes both standard hydraulic brakes
during this phase of braking; the hydraulic brakes are not used. When more
rapid deceleration is required, the hydraulic brakes are activated to provide
additional stopping power.
The sensors can become contaminated with metallic dust and fail to detect
wheel slip; this is not always picked up by the internal ABS controller
diagnostic.
Here, two more sensors are added to help the system work: these are a wheel
angle sensor, and a gyroscopic sensor. The theory of operation is simple:
when the gyroscopic sensor detects that the direction taken by the car doesn't
agree with what the wheel sensor says, the ESC software will brake the
necessary wheel(s) (up to three with the most sophisticated systems) so that
the car goes the way the driver intends. The wheel sensor also helps in the
operation of CBC, since this will tell the ABS that wheels on the outside of the
curve should brake more than wheels on the inside, and by how much.
Given the required reliability it is illustrative to see the choices made in the
design of the ABS system. Proper functioning of the ABS system is considered
of the utmost importance, for safeguarding both the passengers and people
outside of the car. The system is therefore built with some redundancy, and is
designed to monitor its own working and report failures. The entire ABS
system is considered to be a hard real-time system, while the subsystem that
controls the self-diagnosis is considered soft real-time. As stated above, the
general working of the ABS system consists of an electronic unit, also known
as ECU (electronic control unit), which collects data from the sensors and
drives the hydraulic control unit, or HCU, mainly consisting of the valves that
regulate the braking pressure for the wheels.
3.2 PURPOSE OF AUTOMATIC BRAKING SYSTEM
A preceding vehicle following control apparatus includes a sensor sensing an
actual vehicle speed, a sensor sensing an actual vehicle spacing from a
controlled vehicle to a preceding vehicle ahead, and an actuator for regulating
a driving/braking force of the controlled vehicle. A controller controls the
vehicle speed or the vehicle spacing in a following control mode with the
actuator, and starts a deceleration control if an anti-lock brake control is
started in the following control mode. The controller cancels the deceleration
control when the vehicle spacing becomes greater than a predetermined
spacing value
3.2.1 BETTER CONTROL
A vehicle speed sensor to sense an actual vehicle speed of the controlled
vehicle. Vehicle spacing sensor to sense actual vehicle spacing from the
controlled vehicle to a preceding vehicle; a vehicle speed controller to vary
the actual vehicle speed of the controlled vehicle in accordance with a desired
vehicle speed; anti-lock brake controller to perform an anti-lock brake control
for preventing wheel locking; and
vehicle speed controller to determine the desired vehicle speed in accordance
with the actual vehicle speed and the actual vehicle spacing, the controller
comprising,
following control section to perform a preceding vehicle following control by
setting a desired vehicle spacing from the controlled vehicle to a preceding
vehicle in accordance with the actual vehicle speed and actual vehicle spacing
and determining the desired vehicle speed to bring actual vehicle spacing
closer to desired spacing,
deceleration control section to perform a deceleration control determining the
desired vehicle speed to decrease the actual vehicle speed of the controlled
vehicle, and mode change control section to cancel the following control of
the following control section and instead compulsorily initiating the
deceleration control of the deceleration control section in response to a start
of the anti-lock brake control of the anti-lock brake controller.
3.2.2 CUT CAR CRASHES
it detects the risk of a crash, and automatically applies the brakes if it judges
that the car may have trouble avoiding an object. The Collision Mitigation
Brake System (CMS), a world first, also automatically tightens seatbelts just
before a collision. Honda has fitted it to its new top-of-the-range sedan, the
Inspire, which went on sale in June. The Ministry of Land, Infrastructure, and
Transport has taken the lead in encouraging domestic carmakers to develop
advanced safety vehicles (ASVs), and some of these are now approaching the
stage where they are ready for practical use. Automakers are looking to
develop and commercialize a wide range of safety systems to reduce road
risks.
3.2.3 STABLIZATION IN DRIVING
Wall shear stress in postcapillary venules varies widely within and between
tissues and in response to inflammation and exercise. However, the speed at
which leukocytes roll in vivo has been shown to be almost constant within a
wide range of wall shear stress, i.e., force on the cell. Similarly, rolling
velocities on purified selections and their legends in vitro tend to plateau. This
may be important to enable rolling leukocytes to be exposed uniformly to
activating stimuli on endothelium, independent of local homodynamic
conditions. Wall shear stress increases the rate of dissociation of individual
selectin-ligand tether bonds exponentially (, ) thereby destabilizing rolling. We
find that this is compensated by a shear-dependent increase in the number of
bonds per rolling step. We also find an increase in the number of microvillus
tethers to the substrate. This explains (a) the lack of firm adhesion through
selections at low shear stress or high legend density, and (b) the stability of
rolling on selections to wide variation in wall shear stress and legend density,
in contrast to rolling on antibodies (). Furthermore, our data successfully
predict the threshold wall shear stress below which rolling does not occur. This
is a special case of the more general regulation by shear of the number of
bonds, in which the number of bonds falls below one.
3.2.4 FOR MAX. WINDING EFFICENCY
The Automatic Braking System (ABS) supplies the advanced tool required for
efficiently locating and correcting defects. It increases winder or re-reeler
capacity by optimizing the time to locate the defects to be patched or culled.
When manual control is used, the unwinding rate must be reduced to crawl
speed well in advance of suspected problem areas in order to avoid missing
the defect. This often leads to the winder/re-reeler function becoming a bottle-
neck in the paper production line.
Automatic Braking can be effectively utilized in virtually any paper type or
grade.
By taking into consideration both the location of the defect and the limitations
of the customer specific winder drive, Automatic Braking calculates the
optimal speed curve to the defect. It then automatically slows down the drive
to crawl speed or alternately stops the winder or re-reeler at the precise
selected defect location. The status of the unwinding, e.g. the length to the
next stopping position, is continuously updated on the display. With Automatic
Braking, the operators have the additional facility of virtually unwinding the
reel in advance. With the help of the defect classification and high resolution
images, operators are able to easily determine the severity of the defects and
thus minimize unnecessary stops..
3.2.5 PATH FOLLOWER
A Path Follower is an invisible thing that follows a path of Interpolation Points
and can provide something for a camera to aim it if you want the camera to
follow a path with a complicated aiming sequence.
The Path Follower (9071) takes three parameters:
1. low byte: low byte of tid of first Interpolation Point in path.
2. high byte: high byte of tid of first Interpolation Point in path.
3. options: (Add any of the following values; i.e. for options 2 and 4, this
parameter would be 6):
o 1: path is linear instead of curved.
o 2: Camera will adjust its angle to match those of the points it
passes.
o 3: Camera will adjust its pitch to match those of the points it
passes.
o 4: When used with 2 and/or 4, the camera faces in the direction of
movement instead of the direction the Interpolation Points are facing
.
An obstacle detection device for a vehicle includes an area determining section for determining a detection area extended forward of a running vehicle and provided for detecting an obstacle, a split section for splitting the area into a plurality of small split zones, a detecting section for detecting an obstacle in each of the small split zones, inferring section for an inferring a path of the vehicle in the obstacle detection area, and a judging section for judging a rank of danger of an obstacle in the detection area. The obstacle can be properly detected so that the vehicle can take a responsive and appropriate action for avoiding the obstacle.
Path-finder would bear a strong family resemblance to the full-size Armada SUV, we were afraid. Very afraid. The old Path-finder was a good-looking truck, whereas the Armada is the Shrek of its field.
Fortunately, the new Pathfinder has real character, even though the styling is hardly beautiful. Like every new mid-size SUV, it is bigger inside and out, more powerful, and heavier, and it features a third-row seat.
Unlike the old Pathfinder, the new one uses body-on-frame construction. It has upper- and lower-control-arm front and rear suspension, with coil springs and antiroll bars at both ends. Ground clearance varies between 8.5 and 9.2 inches, depending on the model.
The Pathfinder is the first recipient of the latest VQ V-6 engine. Displacing 4.0 liters (in-stead of 3.5), it has been tuned to produce good midrange torque, with 80 percent of the peak 291 pound-feet being available below 2000 revs. It also makes 270 horsepower and mates to a five-speed automatic transmission.
Nissan expects that around 30 percent of Pathfinders will be rear-wheel-drive, but there's a choice of two all-wheel-drive systems: a part-time system that can be shifted on the fly and an on-demand version that shunts up to 50 percent of the torque to the front wheels in case of wheel slippage. All Pathfinders have a standard skid-control system and antilock brakes; all-wheel-drive models also have "Active Braking Limited Slip," which uses the traction-control system to move up to 50 percent of the engine torque to any one wheel. SE Off-Road models with 4wd have hill-descent control and hill-start assist, plus skid plates, Rancho performance dampers, adjustable pedals, and rear A/C. Pathfinders can tow up to 6000 pounds, and a receiver-type hitch is neatly integrated into the rear bumper.
The base XE comes reasonably well equipped, but the SE adds running boards, an easy-clean cargo area, and an eight-way power driver's seat. A six-disc in-dash CD changer, a moonroof, and dual-zone climate control are included in options packages. The upscale LE has cheesy wood-grain trim, leather seats, a power passenger's seat, and full length curtain air bags. A navigation system and DVD entertainment system are optional.
This impressive mid-size SUV rides nicely, steers well, and has good passing performance, although the V-6 lacks the low-down steam of a big American V-8. The five-speed automatic is well matched to the engine, and it's pretty good on back roads. You'll definitely notice the 4400-to-4800-pound bulk as it pummels into deep dips. Off-road, the awd systems will conquer most The mid-size-SUV market is crowded, but the Pathfinder is up near the top. The
CHAPTER 4: Future scope of AUTOMATIC BRAKING AND PATH FINDER
When we heard that the new Path-finder would bear a strong family Fortunately, the new Pathfinder has real character, even though the styling is hardly beautiful. Like every new mid-size SUV, it is bigger inside and out, more powerful, and heavier, and it features a third-row seat.
Pathfinder, the new one uses body-on-frame construction. It has upper- and lower-control-arm front and rear suspension, with coil springs and antiroll bars at both ends. Ground clearance varies between 8.5 and 9.2 inches, depending on the model.
The Pathfinder is the first recipient of the latest VQ V-6 engine. Displacing 4.0 liters (in-stead of 3.5), it has been tuned to produce good midrange torque, with 80 percent of the peak 291 pound-feet being available below 2000 revs. It also makes 270 horsepower and mates to a five-speed automatic transmission.
Pathfinders will be rear-wheel-drive, but there's a choice of two all-wheel-drive systems: a part-time system that can be shifted on the fly and an on-demand version that shunts up to 50 percent of the torque to the front wheels in case of wheel slippage. All Pathfinders have a standard skid-control system and antilock brakes; all-wheel-drive models also have "Active Braking Limited Slip," which uses the traction-control system to move up to 50 percent of the engine torque to any one wheel. Inside, the Pathfinder is spacious and versatile