Upload
tranmien
View
228
Download
0
Embed Size (px)
Citation preview
1
Maize silage LINK Project Consortium
PROJECT H5105200
REPORT
Prediction of the in vivo metabolisable energy value and the in situ degradability of maize silage
from near infrared reflectance spectroscopy and determining the relationship between in situ
and in vitro determinations of degradability:
Measurement of digestibility and degradability
C. Rymer and D.J. Humphries
Food Production and Quality Division
School of Agriculture, Policy and Development
University of Reading
READING
RG6 6AR
2
SUMMARY
A total of 90 samples of maize silage (MS) were collected from commercial farms in the UK over a
two year period (2009/10 and 2010/11). The objective of the project was to determine the ability of
near infrared reflectance spectroscopy (NIRS) to predict digestible organic matter (DOMD) and
metabolisable energy (ME) contents as measured in vivo using sheep at maintenance, and the in situ
degradability (measured using cows) of MS dry matter (DM), nitrogen (N) and starch. In this report,
the measurement of the in vivo and in situ data are described. Silage dry matter (DM) contents ranged
from 211 to 436 g/kg, crude protein contents from 64 to 112 g/kg DM , starch contents from 98 to 367
g/kg DM and neutral detergent fibre contents from 349 to 646 g/kg DM. The predicted metabolisable
energy (ME) contents ranged from 9.1 to 12.0 MJ/kg DM. Silages collected in the second year of the
study were slightly (approx 2%) more digestible than those collected in year 1, and had a slightly
higher crude protein content and pH although this was not related to the increased digestibility. The in
situ rate of dry matter degradation was slow compared with the silages currently in the Feed into Milk
(FiM) database, and the calculated effectively rumen degraded dry matter content (using the FiM
model) was also much lower. However, if the ‘a’ fraction was considered soluble, the effectively
rumen degraded dry matter content was similar. It is proposed that for maize silage this is a more
rational approach as to assume that small starch particles degrade at the same rate as large NDF
particles is erroneous. The estimation of the effectively degraded N content of the silage was not
improved by fitting more than a single curve, described by N degradability = 73.2+11.4(1-e-0.021t
)
where t is time (h). Although mean N solubility was similar to the FiM database, it was very variable
(ranging from 30 to 73%). Determining starch degradability was complicated by the heterogenous
nature of the maize silage, and the difficulty of accurately analysing starch content in forage samples.
Starch was completely degraded and the rate of starch degradation was rapid (0.096/h). If the FiM
model was used to estimate the effective degradability of starch, only 55% was degraded which is
unlikely. The modified FiM model predicts a more realistic effective starch degradability of 81%, and
the maize silage samples studied would then supply between 86 and 306 g effectively degraded
starch/kg DM.
3
INTRODUCTION
Maize silage is a major feed for ruminants, particularly dairy cows, where as much as 75% of the
forage can be fed as maize silage. The area dedicated to forage maize has increased substantially from
35 000 ha in 1990 to approximately 132 000 ha in the latest DEFRA survey (DEFRA, 2011), so that
approximately 2 million cattle are now fed maize silage. Maize is also a flexible alternative to wheat
and can either be harvested for forage maize or diverted to grain maize production, including its use as
a biofuel. Climate change, with a projected increase in ambient temperature of 2oC during the 21
st
century, may significantly increase the amount of forage maize grown, as the ambient temperature
zone for successful cultivation will move further north.
The use of maize silage fed with grass silage, or as a buffer feed with high protein spring grass, can
reduce methane production and nitrogen pollution. Substituting grass silage with maize silage
increased N retention (Browne et al., 2005), increased the efficiency of N utilisation (Burke et al.,
2007), and reduced N and methane excretion (Dijkstra et al., 2009). When fed with red clover silage,
maize silage increased the partitioning of dietary N to milk N rather than urinary N (Dewhurst et al.,
2010).
A system (be it dairy, beef or sheep) that uses maize silage needs to have accurate data on the
chemical composition and nutritive value of that silage if it is to be used efficiently. Indeed, all diet
formulation systems, such as the Feed into Milk system adopted in the UK, rely on accurate estimates
of the energy and nutrient content of forage feeds produced on farm. This involves both the
determination of the total amount of energy and nitrogen available, and also the rate at which nutrients
supplying energy and N are degraded in the rumen.
Maize silage ring test studies completed by the UK Forage Analytical Assurance (FAA) group showed
very poor agreement in the estimate of energy by different silage laboratories (ranging from 10.6 to
12.0 MJ ME/kg DM for a single sample) and poor relationships with the FAA master laboratory (R2
range of 0.25 to 0.62). Modern dairy feeding models now recognise the importance of balancing the
supply of energy and protein both within the rumen (rumen energy to protein ratios) and within the
cow (Metabolisable Protein to ME) ratios. The determination of the rate and extent of rumen
degradable dry matter and N are key inputs required by the Feed into Milk system, as well as a reliable
estimate of the feed’s ME content. Clearly, this requires the ability to predict nutritive values using
rapid techniques such as near infrared reflectance spectroscopy (NIRS).
The FAA group has successfully applied wet NIRS techniques to estimate the nutrient values of grass
silage. A previous LINK project (LK0658), introduced new NIRS equations for whole crop wheat and
barley silages during 2006. For maize silage, there are standard industry equations for the prediction
of dry matter, crude protein, NCGD, starch, ash and NDF content, but there are no agreed methods to
predict the ME or dry matter, starch and nitrogen degradabilities. Currently, individual silage
4
laboratories use different methods to predict ME (for example by using equations based on NCGD)
and degradability values are based on fixed values derived for the FiM model.
In addition to the lack of consistent prediction of the ME content of maize silage, there is no means of
reliably predicting its rumen degradability characteristics. There is no UK published work on a large
scale survey of maize silage degradabilities for dry matter, nitrogen or starch, and the feed industry
currently has to rely on fixed estimates of these important characteristics. The objective of this project
was therefore to determine the ME content and the rate and extent of rumen dry matter, nitrogen and
starch degradability for a wide range of maize silages. These silage samples were then submitted to
Eurofins to derive wet scanning NIRS predictions.
MATERIALS AND METHODS
Sample identification, collection and processing
The Maize Growers Association (MGA) and other commercial partners combined their databases to
assist in the identification and collection of 90 maize silages of known variety, harvest date and
harvest treatment (i.e. rolling/chopping/silage additive etc). The silages were collected from various
UK farm sites over a period of two years. Ten of the samples with differing maturities and
physiological characteristics were provided by Syngenta Seeds. In Appendix 1, Table A.1 summarises
the UK region of origin and cereal varieties. A map showing the sites where the silage samples were
taken from is presented in Figure 1; the large star indicates where the ten (Syngenta) samples were
located. The main criterion when selecting samples was to ensure that as wide a range of sample dry
matter contents as possible were obtained. This was on the basis that this should also result in as wide
a range of ME contents as possible were obtained, to improve the accuracy of ME prediction. In the
first year, most of the samples were collected from the south west of England, and along the M4
corridor. This geographical bias was addressed in the second year, to ensure that samples were also
collected from other major maize growing regions in the country.
A single sample of around 400 kg fresh weight was removed mechanically from a clean area of the
maize silage clamp face. The sample was placed in a large plastic bag and sealed in a 1000 l plastic
container for transport to Reading. Samples were numbered sequentially at source to aid identification.
At the point of collection a photograph was taken of the clamp face and area the sample was taken
from and a close up image was taken of the silage sample showing visually the physical form of the
maize silage. Each sample consisted of approximately 110 kg dry matter, and, collectively, the aim
was to acquire samples ranging in DM content from <250g/kg to >400g/kg. On the day of arrival at
Reading, each sample was mixed for five minutes in a clean diet mixer (Dataranger). The Penn State
Forage and TMR Particle Separator was used to determine forage particle length and particle size
distribution in a representative 1.8 kg sample of each maize (Kononoff et al., 2003). Dry matter
content was determined initially by microwave oven then confirmed by drying triplicate samples (400
g fresh weight) at 100°C for 23 hours.
5
A sample of each silage was submitted to Eurofins for analysis of chemical composition and by NIRS
(using both wet and dry materials). Samples of each silage were also submitted to Bioparametrics for
determination of in vitro gas production profile.
Sample analysis
Digestibility
Digestible organic matter content (DOMD) values were determined to predict the ME content of the
silage. Digestibility of individual maize silages were measured in vivo using 12 mature wether sheep,
of similar breed, liveweight and condition score. Samples were characterised in batches of three (i.e.
using three sheep) using a balanced Latin square design to reduce between animal variation. The
allocation of sheep to forages and weeks of the study is shown in Figure 2a.
In vivo digestibility was estimated by making complete collections of faeces in metabolism cages over
a 5 day period following a 16 day adaptation to the diet (Figure 2b). Maize silage was fed as the sole
diet, supplemented with a sheep mineral/vitamin supplement (17 g/d) and 2 g urea per animal per day
applied in solution (diluted in 20ml water) sprinkled on top of the forage. The amount of maize silage
fed to each sheep was calculated to be sufficient to maintain liveweight (24 g DM/kg liveweight). The
sheep were weighed on a weekly basis and any necessary adjustments in the diets were made. All diets
(including the mineral/vitamin supplement and the urea solution) were fed in equal portions two times
per day.
Following the introduction of the test diet (day 1) the sheep were housed in individual pens with a
plastic mesh lying area to allow drainage. Each pen was fitted with a self-fill water bowl and a feed
trough, and was hosed clean on a daily basis at feeding time. The sheep were fed twice daily at 0900
and 1600 h, with any refused feed being removed prior to the morning feed and recorded. After 16 d
adaptation to the test feed the sheep were placed in metabolism cages for the commencement of faeces
collection (timescale summarised in Figure 2b).
Complete collections of faeces were made at the same time each day during the collection period.
Each day the faeces were placed into individual plastic bags labelled with the sheep identity, the
forage number and the day number. The contents of the five bags collected per sheep over the trial
period were stored at 3-4oC. At the end of the collection period the total faeces were weighed and then
thoroughly mixed. Three representative samples of approximately 400g were taken for dry matter
determinations. A further sample of mixed faeces was stored frozen. Refused feed was bulked over
the collection period for determination of dry matter and ash contents.
During the course of the study it was noticed that there appeared to be diet selection occurring and that
the refused feed removed from the feed trough was of a different physical composition from the feed
offered. If this feed selection was biased toward certain nutrients (such as starch) then this might affect
the estimation of the silage’s ME content. To determine whether this apparent selection did affect the
estimation of nutrient intake, six samples of refused feed from individual sheep periods with a visually
6
different appearance from the original maize silage sample were selected at random and analysed for
dry matter, ash, crude protein and starch.
In situ degradability
Monofilamentous polyester bags (40-45µm pore size, 110-230 mm flat plus 6mm hem) were attached
to a curtain ring and suspended inside the cows’ rumens on a 400 g snap shackle, which in turn was
attached to the rumen cannula. Dry matter content of the sample was determined prior to filling the
bags, with sample sizes standardised at 10 g DM and duplicate bags being prepared for each cow and
time period. Bags were incubated inside the rumen of three cows for 3, 6, 12, 24, 48 and 72 h, with 0 h
bags being processed immediately. Post-incubation all bags (including 0 h bags) were immersed in
cold water to inhibit microbial activity. The bags were then gently rinsed to remove any extraneous
materials from the exterior, gently squeezed of excess moisture and frozen. Once a complete set of
samples was obtained, the bags were defrosted, placed in a net bag and cold washed in a detergent-free
washing machine. The bags were then dried at 60oC for 72 h. Once cooled the samples were
reweighed. The samples were then ground in a Cyclotec mill (1mm screen) for laboratory analysis.
Feeds and residues were analysed for dry matter, nitrogen, starch and ash. The mean in situ
degradability of each maize silage and its composite fractions of nitrogen, organic matter and starch
were then calculated.
Chemical analysis
Dry matter
To determine the dry matter content, 400 g of each maize sample was placed in triplicate in a 100oC
oven for 23 hours (DM = (mass of dried sample – mass of fresh sample) x 100).
Dry matter content was also estimated using a microwave oven technique. Two 100 g samples of fresh
maize were placed into duplicate trays of equal mass. Fresh samples with a dry appearance were
placed in microwave set at full power (850 W) for two minutes prior to being reweighed and the
weight recorded. The sample was then placed in the microwave for one minute three times, with the
weights obtained being recorded after each treatment. The sample was then placed in the microwave
for 30 s and reweighed. This was repeated until constant weights (within 0.1 g) were obtained.
Samples were turned after each treatment to ensure even drying, and were rested for two minutes
between each treatment to allow the evaporation of water vapour and to prevent over-heating. Any
moisture inside the microwave was removed with a paper towel between each drying period. Initially
very dry samples were found to reach a stable weight with fewer drying periods. Some wet samples
required several two minute microwave treatments to remove the initial moisture.
7
Organic matter
A previously dried and milled sample was dried (60oC) in an oven for 1 h to remove residual moisture.
A sample (3 g) was then weighed into a crucible and ashed in a muffle oven at 500oC for 18 h. Once
cool the crucible was reweighed, and organic matter content (OM, g/kg DM) was calculated as:
OM = ((sample weight in – ash weight out)/sample weight in) X 1000
Nitrogen
Nitrogen content was determined using the Kjeldahl method. Samples were prepared by drying at
60oC, grinding and milling to a fine powder in a planetary ball mill. The homogenous sample was then
boiled in concentrated sulphuric acid with Kjeltab catalyst to decompose the nitrogen resulting in an
ammonium sulphate solution. The addition of concentrated sodium hydroxide solution liberated
ammonia gas (through conversion of NH4+ to NH3), which was driven off by steam distillation and
condensed into a boric acid based indicator solution. This receiving solution was then subjected to a
back titration to quantify the amount of ammonia ions in the solution, and hence the nitrogen content.
Starch
Starch content can be defined as the total available carbohydrate less water soluble carbohydrate. Total
available carbohydrate is soluble in hot water, and is broken down to reducing sugars by incubation
with amyloglucosidase and mild acid hydrolysis. To determine total available carbohydrate, the
sample was again dried, ground and milled in a planetary ball mill, prior to being boiled for two hours
and simultaneously mixed every 15 minutes. Amyloglucosidase solution (0.2% w/v in acetate buffer,
pH 4.5) was added, and the solution incubated at 55oC for 1.5 h, and mixed as before. The solution
was then filtered, and the filtrate, and a range of reducing sugar standards, incubated with 0.133M
sulphuric acid at 70oC for 30 minutes. When cooled, the hydrolysate was analysed for reducing sugar
concentration on a continuous flow autoanalyser system.
(a) The carbohydrate content of the sample was calculated as:
CHO =
W
where CHO is the total carbohydrate, D is the dilution factor, which is the extract volume prior to
hydrolysis (ml), C is the concentration of reducing sugar in the hydrolysate (mg/l ) and W is the
weight of sample taken (mg).
(b) The starch content of the sample was then calculated as:
Starch =(0.9 (TC WC) 100)/SR
where Starch is the starch content, a factor of 0.9 is applied to correct for water gained on hydrolysis,
TC is the Total Carbohydrate content as obtained from (a), WC is the Water Soluble Carbohydrate
C D 100
W 1000
8
content as obtained from (a) in a separate sample that was not subjected to the amyloglucosidase
hydrolysis, and SR is the starch recovery (%)
Soluble dry matter and nitrogen
The soluble dry matter and nitrogen contents of each silage were determined to correct for losses of
small particles at 0 h in the in situ technique. A sample (1 g dry matter) was weighed out and soaked
in 100 ml of distilled water for 1 h, swirling every 15 minutes. The sample was then filtered through a
pre weighed filter paper and oven dried at 100oC overnight and then re weighed.
Kjeldahl nitrogen analysis was then performed on the residue.
Soluble DM content (%) = (wt sample*DM/100)-(wt residue)*100
Wt sample* DM/100
Nitrogen solubility (%) = ((( DM in * N% of control) – (Wt of residue * N % of residue))
100 100
/(DM in*N% residue))*100)
100
Statistical analysis
The means, standard deviations, minimum and maximum values were determined for parameters for
the entire sample set (n=90) and also for the two years of sampling (year 1, n=48, year 2 n=42).
Differences between the years were determined by analysis of variance.
DOMD and ME
The dry matter content of the silage was corrected for volatile fermentation products in the calculation
of digestible organic matter in the dry matter (DOMD). This was done using the correction proposed
by Haigh (1979) for maize silage:
Corrected dry matter (CDM) = (0.95 x oven dry matter) + 3.3
where dry matter is expressed as a percentage. The DOMD on a true dry matter basis (DOMDTDM,
g/kg CDM) was then calculated from:
DOMDTDM = 100 – {(100-DOMD) x (ODM/CDM)}
where ODM is oven dry matter (%) and CDM is corrected dry matter. The METDM (MJ/kg CDM)
content of the silage was then predicted from (AFRC, 1993):
METDM = 15.7 x DOMDTDM
9
In situ degradability data
The Ørskov and McDonald (1979) model was fitted to the in situ degradability data,
Degradabilityt (%) = a + b(1-e-ct
)
Where Degradabilityt is degradability at time t, a is the fraction ‘instantaneously’ available, b is the
slowly degraded material and c is the rate of degradation of b. For dry matter degradability, best
subsets and then stepwise regression was used to determine whether there was any relationship
between the chemical composition of maize silage and the rate of dry matter degradation and the
effective degradability of dry matter using the proposed modified FiM model (see below).
Dry matter and N degradability was corrected for material that was ‘lost’ at 0 h by determining the
solubility of dry matter and N. In the FiM model, the degradable material that is available at 0 h is
then determined as the soluble material (s) and a proportion (Bd) of the remaining ‘a’ material:
Bd=b(a-s)/(100-a)
The effective degradability of soluble material and small particles (EDssp) is then calculated as:
EDssp=(0.9s)/(0.9+kliq) + (Bd.c/(c+kliq))
Where kliq is the fractional outflow rate of liquid (0.077 for a 700 kg cow consuming 25 kg DM/d of a
diet comprising 400 g/kg forage).
The effective degradability of large particles (EDlp) was calculated as:
EDlp= bc/c+kf
Where kf is the fractional outflow rate of large forage particles (0.047 for a 700 kg cow consuming 25
kg DM/d of a diet comprising 400 g/kg forage).
The effective degradability of dry matter or N may then be calculated as the sum of EDssp and EDlp.
This approach resulted in unrealistically low estimates of the amount of material degraded in the
rumen. This is a particular issue with a forage such as maize silage, in which small particles (mostly
starch) are ascribed a degradation rate derived from the large particles (mostly NDF). The effective
degradability of material (dry matter, N, organic matter and starch) was therefore also calculated as:
EDDM(a=s) = ((0.9a/(0.9+kliq))+((bc/(c+kf))
thus assuming that the soluble and small particles in maize silage have a common degradation rate of
0.9, and are subject to the liquid outflow rate. This is an adaptation of the FiM approach, rather than
reverting to the earlier estimation of effective degradability (a + (bc/(c+k))), in which it was assumed
that the ‘a’ fraction was completely and instantaneously available.
The analysis of starch degradability is complex as the heterogenous nature of the silage makes it
extremely difficult to obtain truly representative samples of silage for use in the in situ technique. The
analysis of starch in the residues is also complicated by the various stages involved in the analysis. In
10
some cases, this resulted in more than 100% of the degraded organic matter being accounted for, after
taking account of losses from determined degraded N, starch and neutral detergent soluble materials.
In these instances, the estimated starch degradability was corrected, being calculated as the degraded
organic matter content after subtraction of losses from degraded crude protein and neutral detergent
solubles. The Ørskov and McDonald (1979) model was then fitted to individual silage samples.
RESULTS AND DISCUSSION
Sample description
The sites from which samples were collected is summarised in Table A1 of Appendix 1. A range of
varieties were represented in this study, although some farmers did not know or did not report which
variety was used. Five of the silages were reported to have been exposed to frost before harvest, but as
with the variety, this was not always known. Plastic had been used with four of the silage samples.
Chemical and physical composition
A summary description of the chemical composition and particle size of the silages is presented in
Table 1, with values for individual silages presented in Appendix Table A.2. A good range in silage
dry matter was achieved, from 211 to 436 g/kg fresh weight, although these extremes represented very
few silages because of the difficulty in sourcing extremely wet or extremely dry silage. The
distribution of samples of different dry matter ranges that was achieved is illustrated in Figure 3. Most
samples had dry matter contents between 301 and 350 g/kg, reflecting perhaps the norm for maize
silage production in the UK. 78% of the silages used in this study had dry matter contents between
251 and 350 g/kg, and this increases the confidence in prediction equations generated to characterise
silages that are typically produced in the UK. The remaining samples mostly had dry matter contents
between 351 and 400 g/kg. Dry matter content was the criterion for silage selection because of its
indication of plant maturity before ensilage. A large range was required so as to increase the accuracy
of the prediction equations, but to achieve this some atypical silages had to be identified. These
comprised the two extreme groups (n=5 and n=4), which had dry matter contents between 201-250
and 401-450 g/kg respectively.
There was no significant difference in the chemical composition of the silages between the two years,
with the exception of crude protein. The crude protein content of silages in Year 2 was slightly higher
than in Year 1, but in both years the crude protein content was low (approximately 86 g/kg DM), as
would be expected for maize silage. Both starch and NDF content varied considerably (with ranges of
98-367 and 349-646 g/kg DM respectively), reflecting great variation in the maturity of the maize that
was harvested. Dry matter content was positively related to starch and negatively related to NDF
content, with the DM content of the silage accounting for 23.4% of the variation in starch content
17.8% of the variation in NDF content. The relationship between dry matter content and the starch
and dry matter content of maize silage is illustrated in Figure 4. As observed by Givens and Deaville
(2001), the relationship between NDF and DM content was non-linear, although the quadratic
11
equation derived with the samples in this study accounted for less of the variation than in the study
reported by Givens and Deaville (2001). The equation in this study was:
NDF = 1360 - 5.12 DM + 0.00720 DM2, R
2=34.2% (R
2=63.6% for Givens and Deaville, 2001)
The relationship between dry matter and starch was not improved by introducing a quadratic term in
this study.
The chemical composition of these silages was similar to that in the FiM database except for ash
(which was much higher in the FiM database, 60 g/kg compared with 39 g/kg in these samples). The
silages characterised by Givens and Deaville (2001) were also similar, but those reported by De
Boever et al. (2002) had a lower NDF and higher starch content, perhaps reflecting different climatic
conditions between Belgium and the UK.
There was a wide range in the geometric mean particle size of the silage samples, assessed using the
Penn State Particle Separator, with a minimum of 8.3 and a maximum of 19.1 mm. There was a small
negative relationship between particle size and silage dry matter content, with particle size accounting
for 17.8% of the variation in dry matter, but no relationship between particle size and pH (R2=10.5%).
Digestibility
The mean, and the ranges observed, of the digestibility of dry matter, organic matter, DOMD and
predicted ME are presented in Table 2. The silages in year 2 were more digestible (P<0.01) than those
in year 1, even though the silages in year 2 represented a greater range with lower minimum values
than those observed in year 1. This difference in digestibility between the two years (approximately
2.5%) was not reflected in any difference in the in situ rumen degradability, and regression analysis
showed that it was not related to the increased crude protein content observed in year 2 silages
(relationship between dry matter digestibility and silage crude protein content, R2=0.003, P=0.606).
Digestibility values for the individual silages, with their coefficients of variation, are presented in the
Appendix in Table A.3. Determining whole tract apparent digestibility in mature wethers is a robust
and reproducible determination, reflected by the coefficients which were generally below 5%.
The range of DOMD values (and therefore calculated ME values) were similar to those used in the
study by Givens and Deaville (2001), suggesting that there has not been a substantial change in the last
ten years in the composition and nutritive value of maize silages, and also that the silages
characterised by Givens and Deaville (2001) can be included in this database for the prediction of
DOMD and ME.
With regard to the selection by sheep of the forage, the analysis of the original feed and the refused
feed sample are presented in Table 3. Differences in composition between feed offered and refused
can be explained in the main by study practice, the dry matter content in refused feed being lower
(<20%) than offered feed because of water introduced to the feed trough from the drinking bowl.
Paired sample t-test suggested no significant (P=0.223) difference in the starch content of offered and
12
refused feed, which would indicate that the sheep were not preferentially selecting the starchier
fractions of the silage. The only significant (P=0.003) difference between the composition of feed
offered and refused was the ash content which was 27.2% higher in the refused feed (Table 3). In
terms of overall average nutrient intake the differences observed in nutrient composition between feed
offered and refused affected intake by -3.5%, 1.7% and -1.4% for ash, starch and protein respectively
(mean of the six samples analysed).
Degradability and solubility of dry matter
Data for in situ rumen degradability of dry matter are summarised in Table 4. These provide the mean
and range of the estimates of a, b and c, and the solubility of dry matter which is used in the Feed into
Milk diet formulation system to correct for the loss of small particles from the in situ system at 0 h.
The effectively degraded dry matter content (for a 700 kg cow consuming 25 kg/d of a diet comprising
400 g/kg forage), and correcting for the loss of small particles, is also presented. No significant
differences were observed in these parameters between Years 1 and 2. In Appendix Table A.4, the
mean (n=3) in situ degradability determined at each time point, determination of solubility and the
estimated values of a, b and c for each individual silage is presented. The R2 values for these fitted
curves were high (>0.9) indicating that the Ørskov and McDonald (1979) model was appropriate for
these data. The coefficients of variation for the determination of degradability are also presented, and
show that this method has similar repeatability to the determination of whole tract apparent
digestibility. The use of the in situ technique is problematical for a material such as maize silage that
is highly heterogenous, but for the determination of dry matter degradability this did not result in
especially high coefficients of variation.
Compared with the FiM database, the mean values for a and b are similar, but the estimated solubility
of dry matter was lower in these samples compared with the FiM database (14 compared with 31%)
and the rate of degradability was also slower (0.02 compared with 0.1). Using the FiM model, the
calculated mean effective degradability of dry matter (EDDM) was very low (313 g/kg), which seems
unrealistic, particularly when the DOMD values of the silages are considered. This is a consequence
of the relatively low solubility and degradation rate, but as explained in the Materials and Methods,
this seems to be more of a shortcoming of the FiM model when characterising a feed such as maize
silage, rather than the silage itself. When EDDM is calculated assuming that a=s much more realistic
estimates of EDDM are produced, equivalent to 78% of the whole tract apparent dry matter
digestibility (rather than 46%, as was the case with the FiM model). The values in the FiM database
are also more realistic using this modified model, as the estimate of EDDM is then 645 g/kg (similar
to that observed as the mean of this dataset) rather than 936 g/kg.
The rate of degradability (‘c’) was not related to any of the chemical composition parameters
(R2<0.16). However, the ‘c’ value is dependent on the relative values of ‘a’ and ‘b’, so that a highly
degradable silage with a high ‘a’ value can have a relatively low ‘c’ value. The estimate of EDDM is
therefore a better indicator of degradability as it takes account of the three terms that describe the
13
kinetics of degradability. EDDM (calculated using the modified FiM model) was regressed using best
subsets regression with the parameters describing silage chemical composition, and also the mean
particle size. The terms selected from this regression were then tested using stepwise regression.
EDDM was related (R2=0.433, P=0.003, s=30.4) to the silage’s NDF, CP and DM content with the
equation:
EDDM = 568 - 0.431NDF + 1.18CP + 0.200DM
Insofar as silage DM content is an indicator of plant maturity, this relationship suggests that the more
mature a silage (with a higher DM content, lower NDF content and higher starch content, although
starch content was not related to EDDM per se) is more degradable.
Degradability and solubility of N.
The estimation of dry matter degradability for all of the 90 silage samples yielded curves to which the
Ørskov and McDonald (1979) equation could be fitted, which could allow for the prediction of
kinetics of rumen dry matter degradability for individual silages. The same was not the case for the
rumen degradability of N, which was probably because of the low N content of maize silage. Any
contamination with rumen microbial material, especially in the early stages of incubation, potentially
constituted a relatively large proportion of the N detected in the residues. In addition, the
heterogeneity of maize silage, coupled with its low N content, resulted in any errors in the
determination of the N content of in situ residues producing atypical degradation curves. The N
degradability data from most of the silage samples could therefore not be fitted to the Ørskov and
McDonald (1979) equation, and it would not be possible to produce reliable predictions of the N
degradability kinetics for individual silages.
However, the Feed into Milk model for the prediction of N supply requires that all feeds be ascribed
estimates of a, b and c for both DM and N. To determine whether all the samples of maize silage
could have their N degradability described by a single set of parameters, or whether there were distinct
populations within the study set, a single curve was fitted to all the data. The silage samples were then
divided into quintiles, on the basis of DM content, N solubility, soluble N content and washable N loss
(0 h degradability). The estimates of a, b and c for each of these quintiles, together with the measured
N content and N solubility, were then used to calculate the predicted effectively degraded N content
for each silage, using both the Feed into Milk model and the modified model (proposed for maize
silage, in which all ‘a’ material is treated as soluble), assuming a 700 kg cow was fed 25 kg DM/d
comprising 400 g/kg forage. A t test was then used to compare the predicted effectively degraded N
content of the maize silages when either the single, fixed model was used, or the models based on
segregating the silages on the basis of nitrogen solubility or 0 h degradability.
The mean and range of values for N solubility and soluble N content are summarised in Table 5. N
solubility ranged from 29.8 to 72.5%, with maize silage samples taken in year 1 being significantly
(P<0.001) more soluble than those in year 2. The lower N content of year 1 silage samples, however,
14
meant that there was no significant difference (P=0.085) in the soluble N content of silages in the two
years. These data for the individual silage samples are presented in Appendix Table A.6. The
parameters describing the curves fitted for the mean of all data, and for the different quintiles based on
dry matter content, N solubility, soluble N content and 0 h N degradability are summarised in Table 6.
The Ørskov and McDonald (1979) model could not be fitted to the data with the highest 0 h N
degradabilities, and so an effective degradability of N of 0.9 was assumed for these samples. The
Ørskov and McDonald (1979) model was also unsuitable for the silage samples with a high soluble N
content.
There was no evidence, on the basis of mean values for a, b and c and the standard errors, that
separating maize silages on the basis of dry matter content produced degradability curves that were
different from the single curve produced using all the samples of maize silage. This was also the case
for intermediate quintiles for N solubility and soluble N content. However, the silages with the lowest
and highest N solubility, lowest soluble N content, and 0 h N degradability did appear to have lower
‘a’ and higher ‘b’ and ‘c’ values. The mean EDN contents for these silages using the different models
are presented in Table 7. With the FiM model, there were no significant differences in the estimates of
EDN. With the modified FiM model, statistically significant differences (P<0.001, P=0.005
respectively) were observed for the estimates of EDN content for silages with N solubility between 29
and 45%, and for silages with a soluble N content between 3 and 6 g/kg. However, the difference in
the EDN content using the two alternative models was extremely small (approximately 1 g EDN/kg)
which is unlikely to be of any nutritional significance. On the basis of this evidence, therefore, there
would be no benefit in using more than single, fixed, values for a, b and c (with a=73.2, b=11.4 and
c=0.021). The actual estimate of effectively degraded N content of maize silage would then be
moderated by variation in its N content and N solubility.
The mean N solubility and fitted ‘a’ value of these samples was similar to the FiM database value.
However, the ‘b’ values of the FiM database and that of De Boever et al. (2002) were 19 and 22%
respectively, whereas the ‘b’ value for the pooled population of silages in this study was just 11.4%.
The rate of degradation of N, however, was similar for the silages in this study and that reported by De
Boever et al. (2002) and lower than that in the FiM database (0.06).
Degradability of OM and starch.
The curve parameters describing organic matter degradability for the silage samples are summarised in
Table 8. The determination of the effectively degraded organic matter content is derived somewhat
differently than the estimate of ‘fermentable’ organic matter calculated by De Boever et al. (2002), but
the values obtained are somewhat similar, although the maize silages show a greater range in EDOM.
The mean EDOM content of the silages (determined in situ in cows) was 72% of the DOMD content
(determined across the whole tract in sheep).
15
The parameters describing the degradability of starch are summarised in Table 9. The degradability
curves for individual silages were generally such that the Ørskov and McDonald (1979) model could
be fitted, although in many cases it had to be constrained to make a+b≤100. Although there was
variation in the degradability parameters (with ‘a’ ranging from 33 to 92%, ‘b’ from 8 to 66%, and c
from 0.02 to 0.27), the starch in the maize silages was highly degradable. High values of ‘c’ were
associated with samples in which the ‘b’ value was relatively high, so that in all cases the effective
degradability of starch was high. Starch degradability parameters are not included in the FiM
database, so these values cannot be compared.
De Boever et al. (2002) assumed that all starch was potentially degradable, and certainly after 24 h
incubation in the rumen virtually no starch was detected in the residues of the samples used in this
study. Even after 12 h, most starch had been degraded. As with the estimate of effectively degraded
dry matter, the estimate of the effective degradability of starch using the FiM model resulted in very
low values being obtained, which in some instances were lower than the estimated ‘a’ values. The
soluble starch content was not determined in this study, and so correcting for small particle loss of the
starch fraction was difficult (and the very low values of effective degradability were obtained when it
was assumed that starch solubility was zero). The modified FiM model, however (in which the ‘a’
fraction is treated as soluble, and so s=a) produced much more realistic estimates. The true effective
degradability of maize silage starch probably lies somewhere between the two estimates, but is more
likely to be closer to the estimate produced by assuming s=a. The estimates of effective degradability
(calculated by assuming s=a) are summarised in Table 9, and indicate that between 70 and 90% of the
starch would be degraded in the rumen, with a mean (for the 90 silage samples) of 81%. By this
calculation, the amount of degraded starch supplied by these UK silages varies between 86 and 306
g/kg DM (with a mean of 187 g/kg DM, and moderated by the silage’s starch content). This
encompasses the calculated value of the Belgian maize silages characterised by De Boever et al.
(2002), where the mean degraded starch content was 229 g/kg DM.
Relationship between microwave and oven DM
At sample reception and following mixing sample dry matter was initially determined by microwave
oven. The microwave method of determining sample dry matter provided results similar to those
obtained by oven dry matter. Dry matter values obtained by microwave method were on average
(n=90) higher at 322 g/kg (SD 46.1) than oven dry matter (309 g/kg, SD 44.5). Variation between the
two methods was similar at maize silage dry matters from 20 to 45% DM (Figure 4).
CONCLUSIONS
Samples of maize silage, typical of those currently produced in the UK, have been characterised. The
90 samples of maize silage ranged in predicted ME value from 9.1 to 12.0 MJ/kg DM. Using the FiM
model to determine the effective degradability of dry matter, organic matter and starch produced
unrealistic estimates of the amount of material degraded in the rumen. This is because of the
16
heterogenous nature of maize silage, with small starch particles being treated (in the model) like large
fragments of NDF. It is proposed that, for maize silage, the correction for small particle loss is
modified and that the ‘a’ fraction is treated like the soluble fraction (with a degradation rate of 0.9, and
an outflow rate equivalent to the liquid outflow rate. N degradability is best described by a single
curve, with no significant difference in estimated effectively degraded N content when silages were
segregated on the basis of N solubility or soluble N content.
ACKNOWLEDGEMENTS
This work was funded within the LINK Sustainable Livestock Production Programme by DEFRA, and
the support from all members of the Project Management Committee is gratefully acknowledged.
Thanks are also due to staff in the Metabolism and the Meat and Growth Research Unit, especially
Miss D Cockman, Mr D Cox, Mr C Green, Mr P Kirton and Mr R Pilgrim.
REFERENCES
Burke, F. Murphy, J. J. O'Donovan, M. A. O'Mara, F. P. Kavanagh, S. Mulligan, F. J., 2007.
Comparative evaluation of alternative forages to grass silage in the diet of early lactation dairy
cows. J. Dairy Sci.. 90: 2, 908-917
De Boever, J.L., Vanacker, J.M., De Brabander, D.L., 2002. Rumen degradation characteristics of
nutrients in maize silage and evaluation of laboratory measurements and NIRS as predictors.
Anim. Feed Sc. Technol. 101,73-86.
DEFRA (2011) http://www.defra.gov.uk/statistics/files/defra-stats-foodfarm-landuselivestock-june-
statsrelease-englandcropslivestocklabour-111024.pdf
Dewhurst, R. J. Davies, L. J. Kim, E. J., 2010. Effects of mixtures of red clover and maize
silages on the partitioning of dietary nitrogen between milk and urine by dairy cows. Animal.
4, 732-738.
Dijkstra, J. France, J. Ellis, J. L. Kebreab, E. Lopez, S. Reijs, J. W. Bannink, A., 2009. Effects of
nutritional strategies on simulated nitrogen excretion and methane emission in dairy cattle. 7th
International Workshop on Modelling Nutrient Digestion and Utilisation in Farm Animals, Paris,
France, 10-12 September, 2009.pp 394-402.
Givens, D.I., Deaville, E.R., 2001. Comparison of major carbohydrate fractions and cell wall
digestibility in silages made from older and newer maize genotypes grown in the UK. Anim. Feed
Sci. Technol. 89, 69-82.
Haigh, P.M., 1979. A short note on the relationship between oven and toluene dry matter in maize
silage. J. Sci. Food Agric. 30,543-545.
17
Kononoff, P.J., Heinrichs, A.J., Buckmaster, D.R. , 2003. Modification of the Penn State Forage and
Total Mixed Ration Particle Separator and the effects of moisture content on its measurements. J.
Dairy Sci. 86, 1858-1863.
Ørskov, E.R., McDonald, I., 1979. The estimation of protein degradability in the rumen from
incubation measurements weighted according to rate of passage. J. Agric. Sci. 92, 499-503.
18
Figure 1. Map showing the sites of sample collection. (The large star indicates where ten samples
were taken from the same site (Syngenta Seeds)).
19
Wee
Sheep
Week 1 2 3 4 5 6
1 A B C D E F Sheep
2 A B C D E F Week 7 8 9 10 11 12
3 A B C D E F 1 G H I J K L
4 C A B F D E 2 G H I J K L
5 C A B F D E 3 G H I J K L
6 C A B F D E 4 I G H L J K
7 B C A E F D 5 I G H L J K
8 B C A E F D 6 I G H L J K
9 B C A E F D 7 H I G K L J
8 H I G K L J
9 H I G K L J
Figure 2a. Allocation of sheep to forages and the organisation of diet changeovers for the first 12 maize
silage samples. This sequence was repeated a further 6.5 times to complete the study.
Sa Su Mo Tu We Th Fr Sa Su Mo Tu We Th Fr Sa Su Mo Tu We Th Fr
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Diet change Acclimatisation Into crate Collection period
Figure 2b. A timetable of sheep management during the experimental period
20
Figure 3. Distribution of the dry matter contents of the silages used in the study
0
5
10
15
20
25
30
35
40
45
200-250 251-300 301-350 351-400 401-450
Nu
mb
er
of
sam
ple
s
Range of dry matter content (g/kg fresh weight
21
Figure 4. The relationship between starch and neutral detergent fibre and dry matter content for
maize silages used in this study
22
Figure 4. Relationship between the dry matter content of silage when determined by oven or
microwave.
y = 0.932x + 0.9247 R² = 0.9307
20.0
25.0
30.0
35.0
40.0
45.0
50.0
20.0 25.0 30.0 35.0 40.0 45.0 50.0
Ove
n D
M %
Microwave DM%
Dry Matter %
23
Table 1. Chemical composition of the silage samples used in this study (n=90)
Overall Year 1 (n=48) Year 2 (n=42) P1
Mean SD Min Max Mean SD Min Max Mean SD Min Max
Dry matter (g/kg
fresh weight)
313 42.8 211 436 318 43.9 211 426 308 41.4 218 436 0.287
Chemical composition, g/kg dry matter
Organic matter 961 5.9 939 975 961 5.9 939 970 960 6.0 949 975 0.568
Ash 39 5.9 25 61 39 5.9 30 61 40 6.0 25 51 0.568
Crude protein 83 8.8 64 112 81 9.3 64 107 86 7.5 72 112 0.013
Starch 233 56.9 98 367 237 56.1 107 339 227 58.0 98 367 0.411
Neutral detergent
fibre
476 51.3 349 646 474 53.4 349 586 479 49.3 351 646 0.664
pH 3.7 0.19 3.3 4.2 3.6 0.15 3.3 4.1 3.8 0.20 3.4 4.2 <0.001
Mean particle size
(mm)2
12.1 2.25 8.3 19.1 12.2 1.88 9.9 17.6 12.0 2.62 8.3 19.1 0.652
1Significance of the difference between the mean values for the two years.
2Geometric mean particle size determined using the Penn State Particle Separator.
24
Table 2. The mean, minimum and maximum digestibility of dry and organic matter of the maize silage samples used in the study.
Digestibility Overall Year 1 (n=48) Year 2 (n=42) P1
(g/kg) Mean SD Min Max Mean SD Min Max Mean SD Min Max
Dry matter 675 43.8 523 796 668 38.7 550 760 685 48.1 523 796 0.003
Organic matter 688 44.0 532 810 681 38.4 568 766 697 48.9 532 810 0.002
DOM in corrected
dry matter
(DOMDTDM)2
682 35.3 578 763 674 25.4 613 720 691 39.3 578 763 0.017
Predicted ME
(MJ/kg DMcorrected)3
10.7 0.53 9.1 12.0 10.6 0.40 9.6 11.3 10.8 0.62 9.1 12.0 0.017
1Significance of the difference between the mean values for the two years.
2Corrected for losses from fermentation products, with corrected dry matter calculated as (0.95*oven dry matter+3.3)
3Calculated as 0.0157*DOMD
25
Table 3. Analysis of feed offered (maize silage) and refused from individual sheep periods
Chemical composition (g/kg)
Dry Matter Ash Starch Crude protein
Feed 3553 416 40.4 305 77.9
Refs 4603 334 53.4 67 85.0
Feed 3535 257 30.3 186 63.7
Refs 4606 220 40.8 128 65.3
Feed 3585 297 48 178 85.2
Refs 4779 189 74.1 163 114.4
Feed 3587 334 42 156 90.0
Refs 4755 273 52.1 197 101.6
Feed 3586 362 31 146 8.17
Refs 4767 266 55 170 10.14
Feed 3508 293 46 193 6.76
Refs 4507 286 51 156 6.63
Feed (average) 327 39.6 194 7.8
Refs (average) 261 54.4 147 8.9
26
Table 4. The mean, minimum and maximum data describing the in situ rumen degradability of dry matter of the maize silage samples used in the study.
Overall Year 1 (n=48) Year 2 (n=42) P1
Mean SD Min Max Mean SD Min Max Mean SD Min Max
Solubility (%) 13.8 5.41 3.2 28.1 14.2 5.52 3.2 26.6 13.2 5.28 3.3 28.1 0.375
a (%)2
41.7 5.65 25.3 54.1 42.0 6.02 25.3 54.1 41.3 5.24 31.2 51.8 0.560
b (%)3
46.7 6.47 34.4 65.0 46.3 6.02 35.6 64.7 47.2 7.00 34.4 65.0 0.543
c (/h)4
0.021 0.0068 0.009 0.042 0.021 0.0075 0.009 0.042 0.021 0.0060 0.012 0.038 0.825
EDDMFIM (g/kg)5
313 45.3 214 475 314 46.9 215 393 312 43.9 214 475 0.827
EDDMa=s (g/kg)6
524 39.7 391 604 524 40.0 391 600 523 39.8 400 604 0.870
1Significance of the difference between the mean values for the two years.
2’Instantly’ degradable material, comprising both soluble material and small particles
3Slowly degradable material, comprising large particles
4Rate of degradation of ‘b’
5Effectively degraded dry matter content, for a 700 kg cow consuming 25 kg DM/d of a diet comprising 400 g/kg forage using the FIM model.
6Effectively degraded dry matter content, for a 700 kg cow consuming 25 kg DM/d of a diet comprising 400 g/kg forage using the modified FIM model assuming
a=s.
27
Table 5. The mean, minimum and maximum observed solubility of N and soluble N contents of the maize silage samples used in the study.
Overall Year 1 (n=48) Year 2 (n=42) P1
Mean SD Min Max Mean SD Min Max Mean SD Min Max
N solubility (%) 54.3 9.98 29.8 72.5 57.8 7.51 41.1 70.3 50.2 10.95 29.8 72.5 <0.001
Soluble N content
(g/kg DM)
7.3 1.69 3.6 11.3 7.6 1.52 4.7 11.3 6.9 1.82 3.6 11.2 0.085
1Significance of the difference between the mean values for the two years.
28
Table 6. The estimates of N degradability parameters (a, b and c)1 for all samples of maize silage, and for different quintiles based on dry matter content, N
solubility and soluble N content.
Estimated value
SE
P R2
a b c
a b c
a b c
Mean of all samples 73.2 11.4 0.021
0.68 3.48 0.0137
<0.001 0.031 0.194 0.951
Quintiles based on dry matter content 210-280 g/kg 70.6 9.5 0.031
0.52 1.34 0.0110
<0.001 0.002 0.055 0.971
280-300 g/kg 73.0 16.9 0.012
0.61 11.01 0.0113
<0.001 0.199 0.366 0.961
300-320 g/kg 72.6 11.8 0.020
1.01 5.99 0.0202
<0.001 0.121 0.382 0.897
320-340 g/kg 73.6 13.1 0.019
0.83 5.63 0.0154
<0.001 0.080 0.293 0.937
>340 g/kg 76.2 8.9 0.033
1.05 2.44 0.0245
<0.001 0.022 0.253 0.881
Quintiles based on nitrogen solubility 29-45% 64.3 19.9 0.017
1.11 8.87 0.0140
<0.001 0.088 0.288 0.946
45-53% 70.5 13.5 0.027
0.68 2.25 0.0108
<0.001 0.004 0.068 0.972
53-56% 76.5 15.5 0.006
0.61 45.26 0.0208
<0.001 0.749 0.794 0.876
56-61% 74.6 8.6 0.043
1.17 1.90 0.0283
<0.001 0.011 0.201 0.873
62-73% 80.1 12.6 0.008
0.49 17.24 0.0155
<0.001 0.506 0.617 0.929
Quintiles based on soluble N content 3.6-5.7 g/kg 65.0 17.6 0.024
0.75 3.11 0.0094
<0.001 0.005 0.065 0.977
5.7-6.8 g/kg 71.7 12.3 0.027
0.80 2.60 0.0139
<0.001 0.009 0.124 0.954
6.8-7.7 g/kg 77.1 8.1 0.021
0.99 5.29 0.0284
<0.001 0.202 0.502 0.818
7.7-8.7 g/kg 74.8 35.2 0.003
1.04 227.87 0.0247
<0.001 0.885 0.898 0.831
8.7-11.3 g/kg 54.6 27.4 0.612
0.00 0.00 0.0000
<0.001 <0.001 <0.001 0
Quintiles based on 0 h losses 0 h loss 50-60% 57.6 20.1 0.041
1.39 2.38 0.0144
<0.001 0.001 0.046
0 h loss 60-70% 66.4 16.1 0.012
0.89 3.17 0.0120
<0.001 0.007 0.098 0 h loss 70-80% 75.5 17.4 0.006
0.78 50.0 0.0217
<0.001 0.730 0.783
0 h loss 80-90% 85.0 3.5 0.018
0.20 1.38 0.0137
<0.001 0.063 0.252 0 h loss >90% No fit possible
29
Table 7. Comparison of different models with single, fixed values derived from mean of all silage samples used in the study (a=73.2, b=11.4, c=0.021) for
describing the degradability of N in maize silage.
Basis of separating silage samples Mean value for effectively degraded N
content of silage1 (g/kg DM)
SEM Significance (P)
of difference
Fixed value Alternative model between models
Using FiM model
N solubility 29-45%, a=64.3, b=19.9, c=0.017 7.1 7.1 0.20 0.956
N solubility 62-73%, a=80.1, b=12.6, c=0.008 8.8 8.6 0.26 0.535
Soluble N content 22-36 g/kg, a= 65.0, b=17.6, c=0.024 5.1 5.4 0.13 0.117
0 h degradability 7.2 7.6 0.20 0.130
Using modified FiM model
N solubility 29-45%, a=64.3, b=19.9, c=0.017 9.1 8.3 0.12 <0.001
N solubility 62-73%, a=80.1, b=12.6, c=0.008 9.8 10.4 0.29 0.115
Soluble N content 22-36 g/kg, a= 65.0, b=17.6, c=0.024 8.9 8.2 0.16 0.005
0 h degradability 9.5 9.3 0.14 0.151
1Effectively degraded N content calculated using FiM model or modified FiM model (where all ‘a’ is treated as soluble) and outflow rates for liquid and particles
based on a 700 kg cow consuming 25 kg DM/d of a diet consisting of 400 g/kg forage.
30
Table 8. The mean, minimum and maximum data describing the in situ rumen degradability of organic matter of the maize silage samples used in the study.
Overall Year 1 (n=48) Year 2 (n=42) P1
Mean SD Min Max Mean SD Min Max Mean SD Min Max
a (%)2
40.6 5.84 24.6 54.1 41.1 6.15 24.6 54.1 40.1 5.49 29.8 51.2 0.441
b (%)3
47.6 6.77 34.7 66.7 47.2 6.53 36.0 66.1 48.1 7.09 34.7 66.7 0.528
c (/h)4
0.023 0.0144 0.009 0.141 0.024 0.0189 0.009 0.141 0.022 0.0063 0.012 0.038 0.446
EDOMa=s (%)5
52.0 5.15 38.9 80.8 52.5 5.86 38.9 80.8 51.5 4.20 39.1 60.0 0.395
EDOMa=s (g/kg DM)6
491 45.3 373 740 495 51.4 373 740 487 37.4 375 562 0.400
1Significance of the difference between the mean values for the two years.
2’Instantly’ degradable material, comprising both soluble material and small particles
3Slowly degradable material, comprising large particles
4Rate of degradation of ‘b’
5Effective degradability organic matter content of the silage calculated using the modified FiM model (assuming a=s) and assuming an outflow rate of 0.047/h (for
the rage portion of a diet consumed by a 700 kg cow consuming 25 kg DM/d of a diet comprising 400 g/kg forage)
6 Effectively degraded organic matter content of the silage calculated using the modified FiM model, assuming a=s, and assuming an outflow rate of 0.047/h (for the
forage portion of a diet consumed by a 700 kg cow consuming 25 kg DM/d of a diet comprising 400 g/kg forage)
31
Table 9. The mean, minimum and maximum data describing the in situ rumen degradability of starch of the maize silage samples used in the study.
Overall Year 1 (n=48) Year 2 (n=42) P1
Mean SD Min Max Mean SD Min Max Mean SD Min Max
a (%)2
66.1 15.82 33.1 91.9 59.9 14.60 33.1 88.6 73.2 14.22 42.8 91.9 <0.001
b (%)3
33.3 15.59 7.7 65.6 39.5 14.40 11.0 65.6 26.1 13.86 7.7 55.7 <0.001
c (/h)4
0.096 0.0480 0.021 0.269 0.096 0.0434 0.021 0.198 0.096 0.0534 0.034 0.269 0.963
EDSTAFiM (%)5
54.9 11.5 22.1 76.6 56.2 12.77 22.1 72.8 53.4 9.81 33.3 76.6 0.264
EDSTAa=s (%)6
80.8 4.64 70.4 89.7 79.1 3.88 70.4 88.4 82.7 4.71 72.1 89.7 <0.001
[EDSTA]a=s (g/kg)7
187 45.0 86 306 187 44.7 91 279 187 45.9 86 306 0.971
1Significance of the difference between the mean values for the two years.
2’Instantly’ degradable material, comprising both soluble material and small particles
3Slowly degradable material, comprising large particles
4Rate of degradation of ‘b’
5Effectively degradable starch using the FiM model, for a 700 kg cow consuming 25 kg DM/d of a diet comprising 400 g/kg forage assuming no soluble organic
matter present.
6Effectively degradable starch using the modified FiM model (where a=s), for a 700 kg cow consuming 25 kg DM/d of a diet comprising 400 g/kg forage assuming
no soluble organic matter present.
7Effectively degraded starch content calculated using the modified FiM model (where all ‘a’ is treated as soluble), as for (6).