Maintenance and Service Guide · Document Part Number: 416630-003. ... Intel® Core™ Duo and Celeron® and AMD Turion™ 64 Mobile Technology and Mobile AMD Sempron™ processors,

b

Maintenance and Service GuideCompaq Presario V6000 Notebook PC

Document Part Number: 416630-003

April 2007

This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures.

© Copyright 2006, 2007 Hewlett-Packard Development Company, L.P.

Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Intel, Core, and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries and regions. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. AMD, the AMD Arrow logo and combinations thereof are trademarks of Advanced Micro Devices, Inc.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Maintenance and Service GuideCompaq Presario V6000 Notebook PCThird Edition: April 2007First Edition: August 2006Document Part Number: 416630-003

Safety warning notice

ÅWARNING: To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC 60950).

Contents

Contents

1 Product Description

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–21.2 Resetting the Computer. . . . . . . . . . . . . . . . . . . . . . . 1–41.3 Power management . . . . . . . . . . . . . . . . . . . . . . . . . . 1–51.4 External Components . . . . . . . . . . . . . . . . . . . . . . . . 1–61.5 Design overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–22

2 Troubleshooting

2.1 Setup Utility in Windows XP . . . . . . . . . . . . . . . . . . 2–1Using the Setup Utility . . . . . . . . . . . . . . . . . . . . . . . 2–1Setup Utility Menus . . . . . . . . . . . . . . . . . . . . . . . . . 2–5

2.2 Setup Utility in Windows Vista . . . . . . . . . . . . . . . . 2–8Using the Setup Utility . . . . . . . . . . . . . . . . . . . . . . . 2–8Setup Utility Menus . . . . . . . . . . . . . . . . . . . . . . . . 2–11

2.3 Troubleshooting Flowcharts . . . . . . . . . . . . . . . . . . 2–15

Maintenance and Service Guide v

Contents

3 Illustrated Parts Catalog

3.1 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . 3–13.2 Computer Major Components. . . . . . . . . . . . . . . . . . 3–23.3 Display Assembly Components . . . . . . . . . . . . . . . 3–213.4 Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . . 3–233.5 Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–253.6 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–273.7 Sequential Part Number Listing . . . . . . . . . . . . . . . 3–30

4 Removal and Replacement Preliminaries

4.1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14.2 Service Considerations . . . . . . . . . . . . . . . . . . . . . . . 4–2

Plastic Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . . 4–2

4.3 Preventing Damage to Removable Drives . . . . . . . . 4–34.4 Preventing Electrostatic Damage . . . . . . . . . . . . . . . 4–44.5 Packaging and Transporting Precautions . . . . . . . . . 4–54.6 Workstation Precautions . . . . . . . . . . . . . . . . . . . . . . 4–64.7 Grounding Equipment and Methods . . . . . . . . . . . . . 4–7

Maintenance and Service Guide vi

Contents

5 Removal and Replacement Procedures

5.1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–25.2 Disassembly Sequence Chart . . . . . . . . . . . . . . . . . . 5–35.3 Preparing the Computer For Disassembly . . . . . . . . 5–45.4 Hard Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–65.5 Computer Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–105.6 Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–115.7 RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–145.8 Mini Card Module. . . . . . . . . . . . . . . . . . . . . . . . . . 5–155.9 Optical Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–205.10 Switch Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–225.11 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–255.12 Power Button Board . . . . . . . . . . . . . . . . . . . . . . . 5–295.13 Display Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 5–315.14 Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–425.15 Audio Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–485.16 Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . 5–505.17 ExpressCard Assembly . . . . . . . . . . . . . . . . . . . . . 5–525.18 USB/Power Connector Board . . . . . . . . . . . . . . . . 5–555.19 System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–575.20 Fan/Heat Sink Assembly. . . . . . . . . . . . . . . . . . . . 5–615.21 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–64

Maintenance and Service Guide vii

Contents

6 Specifications

A Screw Listing

B Backup and Recovery in Windows XP

C Backup and Recovery in Windows Vista

D Display Component Recycling

E Connector Pin Assignments

F Power Cord Set Requirements

Index

viii Maintenance and Service Guide

1Product Description

The Compaq Presario V6000 Notebook PC offers advanced modularity, Intel® Core™ Duo and Celeron® and AMD Turion™ 64 Mobile Technology and Mobile AMD Sempron™ processors, and extensive multimedia support.

Compaq Presario V6000 Notebook PC

Maintenance and Service Guide 1–1

Product Description

1.1 FeaturesThe following features vary by computer model:

■ Intel Core Duo T7200 (2.00-GHz)■ Intel Core Duo T1350 (1.86-GHz)■ Intel Core Duo T5600 (1.83-GHz)

■ Intel Core Duo T2350 (1.86-GHz)

■ Intel Core Duo T2250 (1.73-GHz)■ Intel Core Duo T5500 (1.66-GHz)■ Intel Core Duo T5200 (1.66-GHz)■ Intel Core Duo T2060 (1.60-GHz)■ Intel Core Duo T2050 (1.60-GHz)■ Intel Celeron 440 (1.86-GHz)■ Intel Celeron 430 (1.73-GHz)■ Intel Celeron 420 (1.60-GHz)■ AMD Turion ML-60 (2.0-GHz)■ AMD Turion ML-56 (1.8-GHz)■ AMD Turion ML-52 (1.6-GHz)■ AMD Turion ML-50 (1.6-GHz)■ Mobile AMD Sempron 3500+ (1.8-GHz)■ Mobile AMD Sempron 3400+ (1.8-GHz)■ Mobile AMD Sempron 3200+ (1.6-GHz)■ 15.4-inch WXGA (1280 × 768) TFT display with over

16.7 million colors, varying by computer model■ 200-, 160-, 120-, 100-, 80-, 60-, and 40-GB high-capacity

hard drive, varying by computer model■ 256-MB DDR synchronous DRAM (SDRAM) at 667 MHz,

expandable to 2.0 GB■ Microsoft® Windows Vista™ Business, Windows Vista

Home Basic, and Windows® XP Professional■ Full-size Windows keyboard with embedded numeric keypad

1–2 Maintenance and Service Guide

Product Description

■ TouchPad pointing device with on/off button and dedicated two-way scroll zone

■ Integrated 10/100 BASE-T Ethernet local area network (LAN) network interface card (NIC) with RJ-45 jack

■ Integrated high-speed 56K modem with RJ-11 jack■ Integrated wireless support for Mini Card IEEE 802.11b and

802.11b/g WLAN device■ Support for ExpressCard■ External 90- or 65-watt AC adapter with 3-wire power cord■ 6-cell or 12-cell Li-Ion battery■ Stereo speakers with volume up and down buttons■ Integrated microphones (select models only)■ Support for the following optical drives:

❏ DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe

❏ DVD±RW/R and CD-RW Double-Layer Combo Drive

❏ DVD/CD-RW Combo Drive

■ Connectors:

❏ Audio-in (microphone)

❏ Audio-out (headphone)

❏ Consumer infrared lens

❏ Docking (select models only)

❏ ExpressCard

❏ External monitor

❏ IEEE 1394 digital (select models only)

❏ Memory Reader (select models only)

❏ Power

❏ RJ-11 (modem)

❏ RJ-45 (network)

❏ S-Video-out (select models only)

❏ Universal Serial Bus (USB) v. 2.0


Product Description

1.2 Resetting the ComputerIf the computer you are servicing has an unknown password, follow these steps to clear the password. These steps also clear CMOS:

1. Prepare the computer for disassembly (refer to Section 5.3, “Preparing the Computer For Disassembly,” for more information).

2. Remove the real-time clock (RTC) battery (refer toSection 5.7, “RTC Battery,” for more information).

3. Wait approximately 5 minutes.

4. Replace the RTC battery and reassemble the computer.

5. Connect AC power to the computer. Do not reinsert any batteries at this time.

6. Turn on the computer.

All passwords and all CMOS settings have been cleared.


Product Description

1.3 Power managementThe computer comes with power management features that extend battery operating time and conserve power. The computer supports the following power management features:

■ Standby

■ Hibernation

■ Setting customization by the user

■ Hotkeys for setting the level of performance

■ Battery calibration

■ Lid switch standby/resume

■ Power button

■ Advanced Configuration and Power Management (ACPM) compliance


Product Description

1.4 External ComponentsThe external components on the front of the computer are shown below and described in Table 1-1.

Front Components

Table 1-1

Front Components

Item Component Function

1 Power light On: The computer is on.Blinking: The computer is in standby.Off: The computer is off or in hibernation.

2 Battery light On: A battery is charging.Blinking: A battery that is the only available power source has reached a low-battery condition. When the battery reaches a critical low-battery condition, the battery light begins blinking rapidly.Off: If the computer is plugged into an external power source, the light is turned off when all batteries in the computer are fully charged. If the computer is not plugged into an external power source, the light stays off until the battery reaches a low-battery condition.


Product Description

3 Drive light Blinks when the hard drive or optical drive is being accessed.

4 Wireless switch Turns the wireless feature on or off, but does not create a wireless connection.

✎ A wireless network must be set up to establish a wireless connection.

5 Wireless light Blue: An integrated wireless device, such as a wireless local area network (LAN) device and/or a Bluetooth® device, is turned on.Amber: All wireless devices are turned off.

6 Consumer infrared lens (select models only)

Receives a signal from the HP Remote Control.

7 Audio-in (microphone) jack

Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.

8 Audio-out (headphone) jack

Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio.

Table 1-1

Front Components (Continued)



Product Description

The external components on the left side of the computer are shown below and described in Table 1-2.

Left-Side Components

Table 1-2

Left-Side Components


1 S-Video-out jack Connects an optional S-Video device such as a television, VCR, camcorder, overhead projector, or video capture card.

2 External monitor port Connects an external VGA monitor or projector.

3 Expansion port 3 Connects the computer to an optional expansion product.

✎ The computer has only one expansion port. The term expansion port 3 describes the type of expansion port.


Product Description

4 RJ-45 (network) jack Connects a network cable.

5 RJ-11 (modem) jack Connects a modem cable.

6 HDMI port (select models only)

Connects an optional audio or video device, such as a high definition television, set-top box, DVD player, or any compatible digital or audio device.

7 USB ports (2) Connect optional USB devices.

8 1394 port (select models only)

Connects an optional IEEE 1394 or 1394a device, such as a camcorder.

9 Memory Reader (select models only)

Supports the following optional digital card formats: Secure Digital (SD) Memory Card, MultiMediaCard (MMC), Secure Digital Input/Output (SD I/O), Memory Stick (MS), Memory Stick Pro (MSP), xD-Picture Card (XD), xDPicture Card (XD) Type M.

Table 1-2

Left-Side Components (Continued)



Product Description

The external components on the right side of the computer are shown below and described in Table 1-3.

Right-Side Components


Product Description

Table 1-3

Right-Side Components


1 ExpressCard slot Supports optional ExpressCard/54 cards.

2 Optical drive Reads an optical disc.

3 USB port (select models only)

Connects an optional USB device.

4 Power connector Connects an AC adapter.

5 Security cable slot Attaches an optional security cable to the computer.

✎ The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.


Product Description

The computer keyboard components are shown below and described in Table 1-4.

Keyboard Components


Product Description

Table 1-4

Keyboard Components


1 Function keys Execute frequently used system functions when pressed in combination with the fn key.

2 caps lock key Enables caps lock and turns on the caps lock light.

3 fn key Executes frequently used system functions when pressed in combination with a function key or the esc key.

4 Windows logo key Displays the Microsoft Windows Start menu.

5 Windows applications key

Displays a shortcut menu for items beneath the pointer.

6 Arrow keys Move the cursor around the screen.

7 Embedded numeric keypad keys

Can be used like the keys on an external numeric keypad.

8 num lock key Enables numeric lock, turns on the embedded numeric keypad, and turns on the num lock light.


Product Description

The computer top components are shown below and described in Table 1-5.

Top Components, Part 1


Product Description

Table 1-5



1 Internal microphones (2, select models only)

Record sound.

✎ If there is a microphone icon next to each microphone opening, your computer has internal microphones.

2 Power button When the computer is

■ Off, press to turn on the computer.

■ On, press to enter hibernation.

■ In standby, briefly press to exit standby.

■ In hibernation, briefly press to exit hibernation.

If the computer has stopped responding and Microsoft® Windows® shutdown procedures cannot be used, press and hold the power button for at least 5 seconds to turn off the computer.

3 Speakers (2) Produce sound.


Product Description

The computer top components are shown below and described in Table 1-6.



Product Description

Table 1-6



1 Media button If QuickPlay is not installed and the computer is

■ On, opens the music program or Media menu, which allows you to select a multimedia program.

■ Off, does not function.

■ In standby, resumes from standby into Windows.

If QuickPlay is installed and the computer is

■ On, opens the music program or Media menu, which allows you to select a multimedia program.

■ Off, opens the music program or the Media menu, which allows you to select a multimedia program.

■ In standby, resumes from standby into Windows.

✎ The media button does not affect the procedure for restoring from hibernation.

2 Volume mute button Mutes and restores speaker sound.

3 Volume scroll zone Adjusts speaker volume. Slide your finger to the left to decrease volume and to the right to increase volume. You can also tap the minus sign on the scroll zone to decrease volume, or you can tap the plus sign on the scroll zone to increase volume.


Product Description

The computer TouchPad components are shown below and described in Table 1-7.

TouchPad Components


Product Description

Table 1-7

Touchpad Components


1 TouchPad light Blue: TouchPad is enabled.Amber: TouchPad is disabled.

2 TouchPad Moves the pointer and selects or activates items on the screen.

3 TouchPad horizontal scroll zone

Allows you to scroll left or right.

4 Left and right TouchPad buttons

Function like the left and right buttons on an external mouse.

5 TouchPad on/off button

Enables/disables the TouchPad.

6 TouchPad vertical scroll zone

Allows you to scroll up or down.


Product Description

The external components on the bottom of the computer are shown below and described in Table 1-8.

Bottom Components

Table 1-8

Bottom Components


1 Battery bay Holds the battery.

2 Battery release latch Releases the battery from the battery bay.

3 Optical drive Reads an optical disc.


Product Description

4 Memory module compartment

Contains the memory module slots, the Mini Card WLAN slot, and the RTC battery.

5 Vents (5) Enable airflow to cool internal components.

✎ The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.

6 Hard drive bay Holds the hard drive.

Table 1-8

Bottom Components (Continued)



Product Description

1.5 Design overviewThis section presents a design overview of key parts and features of the computer. Refer to Chapter 3, “Illustrated Parts Catalog,” to identify replacement parts, and Chapter 5, “Removal and Replacement Procedures,” for disassembly steps.

The system board provides the following device connections:

■ AMD Turion and Mobile AMD Sempron processors

■ Audio

■ Display

■ ExpressCard

■ Fan

■ Hard drive

■ Intel Core Duo and Celeron processors

■ Keyboard and TouchPad

■ Memory module

■ Mini Card module

ÄCAUTION: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left and right sides of the computer.

The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist. These conditions are affected by high external temperatures, system power consumption, power management/battery conservation configurations, battery fast charging, and software. Exhaust air is displaced through the ventilation grill located on the left side of the computer.


2Troubleshooting

ÅWARNING: Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board. Improper repairs can create a safety hazard. Any indication of component replacement or printed wiring board modification may void any warranty or exchange allowances.

2.1 Setup Utility in Windows XPThe Setup Utility is a ROM-based information and customization utility that can be used even when your Windows operating system is not working or will not load.

The utility reports information about the computer and provides settings for startup, security, and other preferences.

1. Turn on or restart the computer in Windows.

2. Before Windows opens and while the “Press <F10> to enter setup” prompt is displayed in the lower-left corner of the screen, press f10.

Using the Setup Utility

Changing the Language of the Setup UtilityThe following procedure explains how to change the language of the Setup Utility. If the computer is not in the Setup Utility, begin at step 1. If the computer is in the Setup Utility, begin at step 2.


Troubleshooting

1. To open the Setup Utility, turn on or restart the computer in Windows, and then press f10 while the prompt, “Press <F10> to enter setup,” is displayed in the lower-left corner of the screen.

2. Use the arrow keys to select System Configuration > Language, and then press enter.

3. Press f5 or f6 (or use the arrow keys) to select a language, and then press enter to select a language.

4. When a confirmation prompt with your preference selected is displayed, press enter to save your preference.

5. To set your preferences and exit the Setup Utility, press f10 and then follow the instructions on the screen.

Your preferences go into effect when the computer restarts in Windows.

Navigating and Selecting in the Setup UtilityBecause the Setup Utility is not Windows-based, it does not support the TouchPad. Navigation and selection are by keystroke.

■ To choose a menu or a menu item, use the arrow keys.

■ To choose an item in a drop-down list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or f5 or f6.

■ To select an item, press enter.

■ To close a text box or return to the menu display, press f1.

■ To display additional navigation and selection information while the Setup Utility is open, press f1.

Displaying System InformationThe following procedure explains how to display system information in the Setup Utility. If the Setup Utility is not open, begin at step 1. If the Setup Utility is open, begin at step 2.


Troubleshooting

1. To start the Setup Utility, turn on or restart the computer in Windows, and then press f10 while the prompt, “Press <F10> to enter setup,” is displayed in the lower-left corner of the screen.

2. Access the system information by using the Main menu.

3. To close the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding Changes, and then press enter. (The computer restarts in Windows.)

Restoring Default Settings in the Setup UtilityThe following procedure explains how to restore the Setup Utility default settings. If the computer is not in the Setup Utility, begin at step 1. If the computer is in the Setup Utility, begin at step 2.

1. To start the Setup Utility, turn on or restart the computer in Windows, and then press f10 while the prompt, “Press <F10> to enter setup,” is displayed in the lower-left corner of the screen.

2. Select Exit > Load Setup Defaults, and then press f10.

3. When the Setup Confirmation is displayed, press enter to save your preferences.

4. To set your preferences and exit the Setup Utility, press f10, and then follow the instructions on the screen.

The Setup Utility default settings are set when you exit the Setup Utility and go into effect when the computer restarts.

✎ Your password, security, and language settings are not changed when you restore the factory default settings.


Troubleshooting

Using Advanced Setup Utility FeaturesThis guide describes the Setup Utility features recommended for all users. For more information about the Setup Utility features recommended for advanced users only, refer to the Help and Support Center, which is accessible only when the computer is in Windows.

The Setup Utility features available for advanced users include a hard drive self-test, a Network Service Boot, and settings for boot order preferences.

The “<F12> to boot from LAN” message that is displayed in the lower-left corner of the screen each time the computer is started or restarted in Windows or restored from hibernation is the prompt for a Network Service Boot.

The “Press <ESC> to change boot order” message that is displayed in the lower-left corner of the screen each time the computer is started or restarted in Windows or restored from hibernation is the prompt to change the boot order.

Closing the Setup UtilityYou can close the Setup Utility with or without saving changes.

■ To close the Setup Utility and save your changes from the current session, use either of the following procedures:

❏ Press f10, and then follow the instructions on the screen.

– or –

❏ If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Saving Changes, and then press enter.

When you use the f10 procedure, you are offered an option to return to the Setup Utility. When you use the Exit Saving Changes procedure, the Setup Utility closes when you press enter.


Troubleshooting

■ To close the Setup Utility without saving your changes from the current session:

If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Discarding Changes, and then press enter.

After the Setup Utility closes, the computer restarts in Windows.

Setup Utility Menus

The menu tables in this section provide an overview of Setup Utility options.

✎ Some of the Setup Utility menu listed in this chapter may not be supported by your computer.

Main Menu

Table 2-1

Main Menu

Select To Do This

System Information ■ View and change the system time and date.

■ View identification information about the computer.

■ View specification information about the processor, memory size, system BIOS, and keyboard controller version (select models only).


Troubleshooting

Security Menu

System Configuration Menu

Table 2-2

Security Menu

Select To Do This

Administrator password Enter, change, or delete an administrator password.

Power-on password Enter, change, or delete a power-on password.

Table 2-3


Select To Do This

Language Support Change the Setup Utility language.

Embedded WLAN Device Radio

Enable/disable an embedded wireless LAN device.

Embedded Bluetooth Device (select models only)

Enable/disable an embedded Bluetooth device (select models only).

Enhanced SATA support (select models only)

Enable/disable enhanced SATA mode.


Troubleshooting

Diagnostics Menu

Boot Options Set the following boot options:

■ f10 and f12 Delay (sec.)—Set the delay for the f10 and f12 functions of the Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).

■ CD-ROM boot—Enable/disable boot from CD-ROM.

■ Floppy boot—Enable/disable boot from Floppy.

■ Internal Network Adapter boot—Enable/disable boot from Internal Network Adapter.

■ Boot Order—Set the boot order for:

❐ USB Floppy❐ ATAPI CD/DVD ROM Drive

❐ Hard drive❐ USB Diskette on Key❐ USB Hard drive

❐ Network adapter

Table 2-4

Diagnostics Menu

Select To Do This

Hard Disk Self Test Run a comprehensive self-test on the hard drive.

Table 2-3

System Configuration Menu (Continued)

Select To Do This


Troubleshooting

2.2 Setup Utility in Windows VistaThe Setup Utility is a ROM-based information and customization utility that can be used even when your Windows® operating system is not working or will not load.

✎ The fingerprint reader (select models only) does not work when accessing the Setup Utility.

The utility reports information about the computer and provides settings for startup, security, and other preferences.

To start the Setup Utility:

1. Turn on or restart the computer.

2. Before Windows opens and while “Press <F10> to enter setup” is displayed in the lower-left corner of the screen, press f10.

Using the Setup Utility

Changing the Language of the Setup UtilityThe following procedure explains how to change the language of the Setup Utility. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.

1. To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press <F10> to enter setup” is displayed in the lower-left corner of the screen.

2. Use the arrow keys to select System Configuration > Language, and then press enter.

3. Press f5 or f6 (or use the arrow keys) to select a language, and then press enter to select a language.

4. When a confirmation prompt with your preference selected is displayed, press enter to save your preference.


Troubleshooting

5. To set your preferences and exit the Setup Utility, press f10 and then follow the instructions on the screen.

Your preferences go into effect when the computer restarts in Windows.

Navigating and Selecting in the Setup UtilityBecause the Setup Utility is not Windows-based, it does not support the TouchPad. Navigation and selection are by keystroke.

■ To choose a menu or a menu item, use the arrow keys.

■ To choose an item in a drop-down list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or f5 or f6.

■ To select an item, press enter.

■ To close a text box or return to the menu display, press esc.

■ To display additional navigation and selection information while the Setup Utility is open, press f1.

Displaying System InformationThe following procedure explains how to display system information in the Setup Utility. If the Setup Utility is not open, begin at step 1. If the Setup Utility is open, begin at step 2.


2. Access the system information by using the Main menu.

3. To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding Changes, and then press enter. (The computer restarts in Windows.)


Troubleshooting

Restoring Default Settings in the Setup UtilityThe following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.


2. Select Exit > Load Setup Defaults, and then press enter.

3. When the Setup Confirmation is displayed, press enter to save your preferences.

4. To set your preferences and exit the Setup Utility, press f10, and then follow the instructions on the screen.

The Setup Utility default settings are set when you exit the Setup Utility and go into effect when the computer restarts.

✎ Your password, security, and language settings are not changed when you restore the factory default settings.

Using Advanced Setup Utility FeaturesThis guide describes the Setup Utility features recommended for all users. For more information about the Setup Utility features recommended for advanced users only, refer to Help and Support, which is accessible only when the computer is in Windows.

The Setup Utility features available for advanced users include a hard drive self-test, a Network Service Boot, and settings for boot order preferences.

The “<F12> to boot from LAN” message that is displayed in the lower-left corner of the screen each time the computer is started or restarted in Windows is the prompt for a Network Service Boot.


Troubleshooting

The “Press <ESC> to change boot order” message that is displayed in the lower-left corner of the screen each time the computer is started or restarted in Windows is the prompt to change the boot order.

Closing the Setup UtilityYou can close the Setup Utility with or without saving changes.

■ To close the Setup Utility and save your changes from the current session, use either of the following procedures:

❏ Press f10, and then follow the instructions on the screen.

– or –

❏ If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Saving Changes, and then press enter.

When you use the f10 procedure, you are offered an option to return to the Setup Utility. When you use the Exit Saving Changes procedure, the Setup Utility closes when you press enter.

■ To close the Setup Utility without saving your changes from the current session:

If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow keys to select Exit > Exit Discarding Changes, and then press enter.

After the Setup Utility closes, the computer restarts in Windows.

Setup Utility Menus

The menu tables in this section provide an overview of Setup Utility options.

✎ Some of the Setup Utility menu items listed in this chapter may not be supported by your computer.


Troubleshooting

Main Menu

Security Menu


Table 2-1

Main Menu

Select To Do This

System Information ■ View and change the system time and date.

■ View identification information about the computer.

■ View specification information about the processor, memory size, system BIOS, and keyboard controller version (select models only).

Table 2-2

Security Menu

Select To Do This

Administrator password Enter, change, or delete an administrator password.

Power-on password Enter, change, or delete a power-on password.

Table 2-3


Select To Do This

Language Support Change the Setup Utility language.

Enhanced SATA support (select models only)

Enable/disable enhanced SATA mode.


Troubleshooting

Boot Options Set the following boot options:

■ f10 and f12 Delay (sec.)—Set the delay for the f10 and f12 functions of the Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).

■ CD-ROM boot—Enable/disable boot from CD-ROM.

■ Floppy boot—Enable/disable boot from Floppy.

■ Internal Network Adapter boot—Enable/disable boot from Internal Network Adapter.

■ Boot Order—Set the boot order for:

❐ USB Floppy❐ ATAPI CD/DVD ROM Drive

❐ Hard drive❐ USB Diskette on Key❐ USB Hard drive

❐ Network adapter

Button Sound (select models only)

Enable/disable the Quick Launch Button tapping sound.

Video memory up to (select models only)

Select the amount of video memory.

Table 2-3


Select To Do This


Troubleshooting

Diagnostics Menu

Table 2-4

Diagnostics Menu

Select To Do This

Hard Disk Self Test Run a comprehensive self-test on the hard drive.

✎ On models with two hard drives, this menu option is called the Primary Hard Disk Self Test.

Secondary Hard Disk Self Test (select models only)

Run a comprehensive self-test on a secondary hard drive.


Troubleshooting

2.3 Troubleshooting Flowcharts

Table 2-5

Troubleshooting Flowcharts Overview

Flowchart Description

2.1 “Flowchart 2.1—Initial Troubleshooting”

2.2 “Flowchart 2.2—No Power, Part 1”




2.6 “Flowchart 2.6—No Video, Part 1”

2.7 “Flowchart 2.7—No Video, Part 2”

2.8 “Flowchart 2.8—Nonfunctioning Docking Device (if applicable)”

2.9 “Flowchart 2.9—No Operating System (OS) Loading”

2.10 “Flowchart 2.10—No OS Loading, Hard Drive, Part 1”



2.13 “Flowchart 2.13—No OS Loading, Diskette Drive”


Troubleshooting

Flowchart Description

2.14 “Flowchart 2.14—No OS Loading, Optical Drive”

2.15 “Flowchart 2.15—No Audio, Part 1”

2.16 “Flowchart 2.16—No Audio, Part 2”

2.17 “Flowchart 2.17—Nonfunctioning Device”

2.18 “Flowchart 2.18—Nonfunctioning Keyboard”

2.19 “Flowchart 2.19—Nonfunctioning Pointing Device”

2.20 “Flowchart 2.20—No Network/Modem Connection”

Table 2-5

Troubleshooting Flowcharts Overview (Continued)


Troubleshooting

Flowchart 2.1—Initial Troubleshooting

Connectingto networkor modem?

Begintroubleshooting.

Is therepower?

Is the OSloading?

Is there video?(no boot)

Is theresound?

Beeps,LEDs, or errormessages?

Keyboard/pointingdevice

working?

Go to“Flowchart

2.17—Nonfunc-tioning Device.”

Go to“Flowchart

2.2—No Power, Part 1.”

Go to“Flowchart

2.6—No Video, Part 1.”

All drivesworking?

Y

Y

Y

Y

Y

Y

Y

Y

N

N

N

N

N

End

N

N

N

Go to“Flowchart

2.9—No Operating System (OS)

Loading.”

Go to“Flowchart

2.15—No Audio, Part 1.”

Go to“Flowchart

2.18—Nonfunc-tioning Keyboard”

or “Flowchart 2.19—Nonfunc-tioning Pointing

Device.”

CheckLED board,

speakerconnections.

Go to“Flowchart 2.20—No

Network/Modem Connection.”


Troubleshooting

Flowchart 2.2—No Power, Part 1

1. Reseat the power cables in the docking device and at the AC outlet.

2. Ensure the AC power source is active.3. Ensure that the power strip is working.

Done

Remove fromdocking device(if applicable).

Power upon battery

power?

Power upon AC

power?

Power up in docking device?

Power upon battery

power?

Power upin docking

device?

Done

Reset power.*

Reset power.*

Power upon AC power?

N

Y

Y

N

N

Y

N

N

Y

Y

Y N

1. On select models, there is a separate reset button.

2. On select models, the computer can be reset using the standby switch and either the lid switch or the main power switch.

*NOTES

Go to“Flowchart


Go to“Flowchart


Go to“Flowchart

2.8—Nonfunctioning Docking Device (if

applicable).”

No power (power LED

is off).


Troubleshooting


Continued from“Flowchart


Visually check fordebris in batterysocket and clean

if necessary.

Done

N

Y

Power on?

Check battery byrecharging it,moving it to

another computer,or replacing it.

Power on?

Done

Y

Replacepower supply(if applicable).

N

Power on?

Done

Y

NGo to

“Flowchart 2.4—No Power,

Part 3.”


Troubleshooting




Reseat AC adapterin computer andat power source.

Internal orexternal ACadapter?

Done

Done

DoneDone

Power on?

Power on?

Power on?

Plug directlyinto AC outlet.

Power LEDon?

Power outletactive?

Try differentoutlet.

Replace externalAC adapter.

Replacepower cord.

Y

N

Y

Y

Y

Y

N

N

N

N

External

InternalGo to

“Flowchart 2.5—No Power,

Part 4.”


Troubleshooting


Y

N



Reseat loosecomponents and

boards and replace damaged

items.

Opencomputer.

Loose ordamaged

parts?

Y

Closecomputer and

retest.

Power on?

Done

N

Replace the following items (if applicable). Check computer operation after each replacement:1. Internal DC-DC converter*2. Internal AC adapter3. Processor board*4. System board*

*NOTE: Replace these items as a set to prevent shorting out among components.


Troubleshooting

Flowchart 2.6—No Video, Part 1

A

N

Stand-aloneor docking

device?

No video.

Replace the following one at a time. Test after each replacement.1. Cable between computer and computer display (if applicable)2. Display3. System board

Internal orexternaldisplay*?

Adjustbrightness. Video OK? Done

Docking Device

Internal

Stand-alone

External

Adjustbrightness.

Video OK? Done

Y

Press lidswitch to ensure

operation.

Video OK? Done

Y

N

Video OK?

Done Done

N

Check for bentpins on cable.

Tryanotherdisplay.

Internal andexternal

video OK?

Replacesystemboard.

Y Y

NN

*NOTE: To change from internal to external display, use the hotkey combination.

Y

Go to“Flowchart



Troubleshooting

Flowchart 2.7—No Video, Part 2

Y

N



Done

Adjust externalmonitor display.

Video OK?

Adjustdisplay

brightness.

Video OK?

Video OK?

Done

Done

Check that computer is properlyseated in docking device,

for bent pins on cable,and for monitor connection.

Go to “A” in“Flowchart


Check brightnessof externalmonitor.

Try anotherexternalmonitor.

Internaland externalvideo OK?

Go to“Flowchart

2.8—Nonfunctioning Docking Device (if

applicable).”

Y

Y

Y

N

N

N

Remove computer from docking device,

if connected.


Troubleshooting

Flowchart 2.8—Nonfunctioning Docking Device(if applicable)

Y

N

Reseat power cord in docking

device andpower outlet.

N

Check voltagesetting on docking

device.

Reset monitorcable connector at

docking device.

Reinstallcomputer into

docking device.

Docking device

operating?

Docking device

operating?Done

Done

Y

Nonfunctioningdocking device.

Remove computer, replace docking

device.

Test replacement docking device with

new computer.


Troubleshooting

Flowchart 2.9—No Operating System (OS) Loading

No OS loading from hard drive,go to “Flowchart 2.10—No OS Loading,

Hard Drive, Part 1.”

Reseat powercord in docking

device andpower outlet.

No OSloading.*

*NOTE: Before beginning troubleshooting, always check cable connections, cable ends, and drives for bent or damaged pins.

No OS loading from diskette drive,go to “Flowchart 2.13—No OS Loading,

Diskette Drive.”

No OS loading from optical drive,go to “Flowchart 2.14—No OS Loading,

Optical Drive.”

No OS loading from network,go to “Flowchart 2.20—No Network/Modem

Connection.”


Troubleshooting

Flowchart 2.10—No OS Loading, Hard Drive, Part 1

Go to“Flowchart

2.17—Nonfunctioning Device.”

Y

Done

N

OS notloading fromhard drive.

Nonsystemdisk message?

Go to“Flowchart

2.11—No OS Loading,


Reseatexternal

hard drive.

OS loading? Done

BootfromCD?

Go to“Flowchart


Diskette Drive.”

Bootfrom

hard drive?

Bootfrom

diskette?

Change bootpriority throughthe Setup Utility

and reboot.

Bootfrom

hard drive?

Y

Y

Y

Y

Y

N

N

N

N

N

Check the Setuputility for correct

booting order.


Troubleshooting


Load OS using Operating System disc

(if applicable).



Hard Drive, Part 1.”Reseat

hard drive.

Done

Disc ordiskette in

drive?

1. Replace hard drive.

2. Replace system board.

Go to“Flowchart


Diskette Drive.”

Format hard driveand bring toa bootableC:\ prompt.

Create partition, and then format

hard drive to bootable

C:\ prompt.

Bootfrom diskette

drive?

Remove disc ordiskette and

reboot.

Y

N

Bootfrom

hard drive?

Y

N

Y

N

Hard drive accessible?

Y

N

Hard driveaccessible?

Done

Run FDISK.

Y

N

Hard drivepartitioned?

Hard driveformatted?

Y

N

Y

N

Computerbooted?

Done

Y

NGo to

“Flowchart 2.12—No OS

Loading, Hard Drive, Part 3.”

Go to“Flowchart




Troubleshooting


Y

Systemfiles on hard

drive?




Clean virus. Done

N

Install OSand reboot.

Viruson

hard drive?

OSloading fromhard drive?

Y

N

Y

N

Y

N

Diagnostics on disc or diskette?

Replacehard drive.

Run diagnosticsand follow

recommendations.

Run SCANDISK and check for

bad sectors.

Can badsectors

be fixed?

Replacehard drive.

Y

N

Y

N

Fix badsectors.

Boot fromhard drive?

Replacehard drive.

Done


Troubleshooting

Flowchart 2.13—No OS Loading, Diskette Drive

Replace the following components individually, retesting after each replacement:■ Diskette drive■ System board

Done

Y

N

Reseatdiskette drive.

OS not loadingfrom

diskette drive.

Done

Y

Y

YY

Y Y

YN

N

N

N

N

N

N

OSloading?

Nonsystemdisk message?

Bootablediskettein drive?

Install bootablediskette and

reboot computer.

Check diskettefor system files.

Try differentdiskette.

Nonsystemdisk error?

OSloading?

Bootfrom another

device?

Enable driveand cold boot

computer.

Is diskettedrive boot

order correct?

Change bootpriority using

the Setup Utility.

Go to“Flowchart

2.17—Nonfunc-tioning Device.”

Diskettedrive enabledin the Setup

utility?

Go to“Flowchart


Reset the computer. Refer to

Section 1.2, “Resetting the Computer,” for

instructions.


Troubleshooting

Flowchart 2.14—No OS Loading, Optical Drive

Y

Done

N

Bootabledisc indrive?

Discin drive?

No OSloading fromCD-ROM or

DVD-ROM drive.

Install bootabledisc andreboot

computer.

Go to“Flowchart


Go to“Flowchart


Installbootable disc.

Boots fromCD or DVD?

Boots fromCD or DVD?

Try anotherbootable disc.

Bootingfrom another

device?

Bootingorder

correct?

Correct bootorder using

the Setup Utility.

DoneReseatdrive.

Y

Y

Y

Y

Y

N

N

N

N

N

Reset the computer. Refer to

Section 1.2, “Resetting the Computer,” for

instructions.


Troubleshooting

Flowchart 2.15—No Audio, Part 1

No audio.

N

Computer indocking device(if applicable)?

Internalaudio?

Audio? Done

Undock

Audio? Done

Turn up audiointernally orexternally.

Go to“Flowchart


Go to“Flowchart


Y

Y

Y

Y

N

N

N

Go to“Flowchart


Replace the docking device.


Troubleshooting

Flowchart 2.16—No Audio, Part 2

Y N

Continued from “Flowchart


Reloadaudio drivers.

Audiodriver in OSconfigured?

Audio?

Y

Y

YN

N

N

Correctdrivers for

application?

Connect toexternalspeaker.

Load drivers andset configuration

in OS.

Audio? Done

Replace audioboard andspeaker

connectionsin computer

(if applicable).

Replace the following components individually, retesting after each replacement:■ Internal speakers■ Audio board (if applicable)


Troubleshooting

Flowchart 2.17—Nonfunctioning Device

Done

Any physicaldevice detected?

Y

N

Unplug the nonfunctioning device from the computer and inspect cables and plugs for bent or broken pins

or other damage.

Reseat device.

ClearCMOS.

Done

Fix orreplace

broken item.

Nonfunctioningdevice.

Reattach device.Close computer,plug in power,

and reboot.

Deviceboots

properly?

Go to“Flowchart 2.9—No

Operating System (OS) Loading.”

Deviceboots

properly?

Replace hard drive.

Replace diskette drive.

Replace NIC.If integrated NIC,replace system

board.Y

N

Y

N


Troubleshooting

Flowchart 2.18—Nonfunctioning Keyboard

Y

N

Keyboardoperatingproperly?

Keyboardnot operating

properly.

Externaldeviceworks?

Replacesystemboard.

Replacesystemboard.

Connect computerto good external

keyboard.

Reseat internal keyboardconnector

(if applicable).

Replace internalkeyboard or

cable.

Y

N

Y

N

Done DoneKeyboardoperatingproperly?


Troubleshooting

Flowchart 2.19—Nonfunctioning Pointing Device

Y

N

Pointing devicenot operating

properly.

Externaldeviceworks?

Replacesystemboard.

Replacesystemboard.

Connect computerto good externalpointing device.

Reseat internalpointing device

connector (if applicable).

Replace internalpointing device

or cable.

Y

N

Y

N

Done Done

Pointing deviceoperatingproperly?

Pointing deviceoperatingproperly?


Troubleshooting

Flowchart 2.20—No Network/Modem Connection

Y

Disconnect allpower from

the computerand open.

No networkor modem

connection.

N

Done

Digitalline?

Networkor modem jack

active?

Replace jack or have jack activated.

Connectto nondigital

line.

NIC/modem configured

in OS?

Reloaddrivers and reconfigure.

Reseat NIC/modem(if applicable).

ReplaceNIC/modem

(if applicable).

Replacesystemboard.

Done

N

N

N

N

Y

Y

Y

Y

Networkor modem connection working?

Networkor modem connection working?


3Illustrated Parts Catalog

This chapter provides an illustrated parts breakdown and a reference for spare part numbers and option part numbers.

3.1 Serial Number LocationWhen ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer.


Illustrated Parts Catalog

3.2 Computer Major Components

Computer Major Components



Table 3-1

Spare Parts: Computer Major Components

Item DescriptionSpare Part Number

1 Display assemblies (include wireless antenna transceivers and cables)

For use with full-featured computer models (includes microphones)

15.4-inch, WXGA, TFT with BrightView15.4-inch, WXGA, TFT Antiglare

432304-001432305-001

For use with defeatured computer models (does not include microphones)


432302-001432303-001

✎ Refer to Section 3.3, “Display Assembly Components,” for display assembly internal component spare part number information.

2 Switch covers (include LED board and LED board cable)

For use with full-featured computer modelsFor use with defeatured computer models

431425-001431424-001

3 Power button board (includes power button board cable)

431438-001

4 Keyboards

For use with all computer models in the following countries or regions:

FranceFrench Canada

ItalyThe Netherlands

441428-051441428-121

441428-061441428-331

SpainThe United Kingdom

The United States

441428-071441428-031

441428-001






Table 3-1

Spare Parts: Computer Major Components (Continued)


4 Keyboards (Continued)

For use only with computer models using Intel processors in the following countries or regions:

Latin AmericaSaudi Arabia

441428-161441428-171

TaiwanThailand

441428-AB1441428-281

For use only with computer models using AMD processors in the following countries or regions:

Denmark, Finland, Norway, and Sweden

441428-DH1 Korea 441428-AD1

For UK OTC ID only 443689-001

5 Top covers (include speakers, TouchPad and TouchPad cable)


438186-001438187-001

6 Fan/heat sink assemblies (include thermal pads)

For use only with computer models using Intel processors

434746-001

For use only with computer models using AMD processors

431450-001

7 ExpressCard assembly 431440-001



Plastics Kit 438469-001

8a

8b8c

Includes:ExpressCard slot bezelHard drive cover (includes 2 captive screws, secured by C-clips)Memory module compartment cover (includes 3 captive screws, secured by C-clips)

9 Processors (include thermal pad)

Intel Core Duo T7200 (2.00-GHz)Intel Core Duo T1350 (1.86-GHz)Intel Core Duo T5600 (1.83-GHz)Intel Core Duo T2350 (1.60-GHz), for V6200 modelsIntel Core Duo T2250 (1.73-GHz)Intel Core Duo T5500 (1.66-GHz)Intel Core Duo T5200 (1.66-GHz), for V6200 modelsIntel Core Duo T2060 (1.60-GHz), for V6200 modelsIntel Core Duo T2050 (1.60-GHz)

434730-001430896-001434731-001441762-001430897-001436157-001436900-001441763-001430898-001

Intel Celeron 440 (1.86-GHz), for V6200 modelsIntel Celeron 430 (1.73-GHz)Intel Celeron 420 (1.60-GHz)

441761-001436159-001434735-001

AMD Turion ML-60 (2.0-GHz)AMD Turion ML-56 (1.8-GHz)AMD Turion ML-52 (1.6-GHz)AMD Turion ML-50 (1.6-GHz)

436257-001431373-001

431372-001431371-001

Mobile AMD Sempron 3500+ (1.8-GHz)Mobile AMD Sempron 3400+ (1.8-GHz)

Mobile AMD Sempron 3200+ (1.6-GHz)

434414-001431375-001

431374-001

Table 3-1








Table 3-1



10 Bluetooth module (includes Bluetooth module cable)

412766-001

11 System boards

945GM, for use only with full-featured computer models using Intel processors940GML, for use only with defeatured computer models using Intel processors943GM - for use only with defeatured models945PM - for Germany only

434725-001

434726-001

444479-001441677-001

For use only with full-featured computer models using AMD processorsFor use only with defeatured computer models using AMD processors

431364-001

431365-001

12 USB/power connector boards (include USB/power connector board cable)

For use with 90-W AC adaptersFor use with 65-W AC adapters

431446-001431445-001

13 Audio boards

For use with full-featured computer models (includes infrared lens)For use with defeatured computer models (does not include infrared lens)

431443-001

431444-001

14 Batteries

12-cell, 8.8-Ahr6-cell, 4.0-Ahr

432307-001

432306-001






Table 3-1



15 Base enclosures (include wireless switch)

For use with full-featured computer models For use with defeatured computer models

431427-001438316-001

16 Optical drives (include bezel)

DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribeDVD±RW/R and CD-RW Double-Layer Combo DriveDVD/CD-RW Combo Drive

431413-001

431412-001431411-001

17 Hard drives (all 5400-rpm, include bracket and connector)

For use with all computer models:

200-GB (4200-rpm)160-GB (5400-rpm)120-GB100-GB80-GB60-GB

441424-001

438485-001431407-001431406-001

431405-001431404-001

40-GB hard drive for use only with computer models using Intel processors

434743-001

40-GB hard drive for use only with computer models using AMD processors

434415-001






Table 3-1



18 Mini Card modules

802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the countries or regions listed below. These countries or regions are categorized as most of the world 1 (MOW1).

407674-001

Antigua & Barbuda

ArgentinaAustraliaBahamasBarbadosBrunei

CanadaChileDominican Republic

GuamGuatemalaHong Kong

PanamaIndiaIndonesiaMalaysiaMexicoNew Zealand

ParaguaySaudi ArabiaTaiwanThe United States

Vietnam

802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the countries or regions listed below. These countries or regions are categorized as most of the world 2 (MOW2).

407674-002

ArubaAustriaAzerbaijanBahrainBelgiumBermudaBulgariaCayman IslandsColumbiaCroatiaCyprusThe Czech Republic

Denmark

EgyptEl SalvadorEstoniaFinlandFranceGeorgiaGermanyGreeceHungaryIcelandIrelandItalyLatviaLebanon

The PhilippinesPolandPortugalRomaniaRussiaSerbia and Montenegro

SingaporeSlovakiaLiechtensteinLithuaniaLuxembourgMaltaMonaco

The Netherlands

NorwayOmanSloveniaSouth AfricaSpainSri LankaSwedenSwitzerlandTurkeyThe UnitedKingdomUzbekistan






Table 3-1



18 Mini Card modules (Continued)

802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the countries or regions listed below. These countries or regions are categorized as the rest of the world (ROW).

407674-003

ChinaEcuador

Haiti

HondurasPakistan

Peru

QatarSouth Korea

UruguayVenezuela

802.11b/g WLAN Mini Card module for use in Costa Rica, Israel, Kuwait, Thailand, UAE, Ukraine.

407674-004

802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan

407674-291






Table 3-1




802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the MOW countries or regions listed below:

407160-001

Antigua & Barbuda

ArgentinaAruba

AustraliaAustriaAzerbaijan

BahamasBahrainBarbados

BelgiumBermudaBrunei

BulgariaCanadaCayman Islands

Czech RepublicChile

ColumbiaCroatia

CyprusDenmark

Dominican Republic

EgyptEl SalvadorEstonia

FinlandFranceGeorgia

GermanyGreeceGuam

GuatemalaHong KongHungary

IcelandIndia

IndonesiaIreland

ItalyLatvia

LebanonLiechtensteinLithuania

LuxembourgMalaysiaMalta

MexicoMonacoThe Netherlands

New ZealandNorwayOman

PanamaParaguayThe Philippines

PolandPortugal

Romania

RussiaSaudi Arabia

Serbia and Montenegro

SingaporeSlovakiaSlovenia

South AfricaSpainSri Lanka

SwedenSwitzerlandTaiwan

TurkeyUnited Kingdom

United States

Uzbekistan

Vietnam






Table 3-1




802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the ROW countries or regions listed below:

407160-002

ChinaEcuadorHaiti

HondurasPakistanPeru

QatarSouth Korea

UruguayVenezuela

802.11b/g WLAN Mini Card module for use with all computer models in the MOW countries or regions listed below:

407159-001

Antigua & Barbuda

ArgentinaArubaAustraliaAustriaAzerbaijanBahamasBahrainBarbadosBelgiumBermudaBruneiBulgariaCanadaThe Cayman Islands

The Czech Republic

ChileColumbia

CroatiaCyprusDenmarkThe Dominican Republic

EgyptEl SalvadorEstoniaFinlandFranceGeorgiaGermanyGreeceGuamGuatemalaHong KongHungaryIcelandIndiaIndonesia

IrelandItalyLatviaLebanonLiechtensteinLithuaniaLuxembourgMalaysiaMaltaMexicoMonacoThe NetherlandsNew ZealandNorwayOmanPanamaParaguayThe PhilippinesPolandPortugalRomania

RussiaSaudi ArabiaSerbia and Montenegro

SingaporeSlovakiaSloveniaSouth AfricaSpainSri LankaSwedenSwitzerlandTaiwanTurkeyThe United Kingdom

The United States

UzbekistanVietnam






Table 3-1




802.11b/g WLAN Mini Card module for use with all computer models in the ROW countries or regions listed below:

407159-002

ChinaEcuadorHaiti


QatarSouth Korea

UruguayVenezuela

802.11b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan

407159-291

19 RTC battery (includes 2-sided tape) 431436-001

20 Memory modules, PC2-5300, 667-MHz, 1-DIMM


1024-MB512-MB256-MB

434742-001434741-001434740-001


1024-MB512-MB256-MB

431403-001431402-001431401-001

Cable Kit (not illustrated) 434984-001



3.3 Display Assembly Components

Display Assembly Components

Table 3-2


Spare Part Number Information


1 Display bezels

For use with full-featured computer models (includes microphone openings)For use with defeatured computer models (does not include microphone openings)

433283-001

433284-001

2 Display inverter 431391-001



3 Display Hinge Kit (includes left and right display hinges)

433288-001

4 Display panels

15.4-inch, WXGA, SVA display panel with BrightView15.4-inch, WXGA, SVA display panel AntiGlare

431386-001431387-001

5 Wireless antenna transceivers and cables 431398-001

6 Microphone 431393-001

7 Display enclosures


431390-001432920-001

Display Screw Kit (includes screws and rubber screw covers, not illustrated)

431400-001

Display Cable Kit (not illustrated) 433287-001

Table 3-2


Spare Part Number Information (Continued)




3.4 Mass Storage Devices

Mass Storage Devices



Table 3-3

Mass Storage Devices



1 Hard drives (all 5400-rpm, include bracket and connector)

For use with all computer models

200-GB (4200-rpm)160-GB (5400-rpm)120-GB100-GB80-GB60-GB

441424-001438485-001431407-001431406-001431405-001431404-001


434743-001


434415-001

Hard Drive Bracket Kit (includes hard drive bracket and screws used to secure the bracket to the hard drive)

436156-001

2 Optical drives


431413-001

431412-001431411-001

USB digital drive (not illustrated) 364727-001



3.5 Plastics Kit

Plastics Kit Components



Table 3-4

Plastics Kit



Plastics Kit 438669-001

123

Includes:ExpressCard slot bezelHard drive cover (includes 2 captive screws, secured by C-clips)Memory module compartment cover (includes 3 captive screws, secured by C-clips)



3.6 Miscellaneous

Table 3-5

Spare Parts: Miscellaneous

DescriptionSpare Part Number

AC adapters

HP 90-W PFC AC AdapterHP 90-W non-PFC AC AdapterHP 65-W AC Adapter

432309-001432310-001402018-001

Analog TV tuner 407941-001

DVB-T TV tuner 412175-001

Composite S-Video and audio input cable 407939-001

Headset 371693-001

Backpack 405527-001

HP Remote Control 407313-001

HP Remote Control 435743-001

Remote control, ExpressCard 439128-001

Remote control, ExpressCard (EMEA) 439254-001

Infrared emitter 439129-001

Logo Kit 431435-001

RF cable 408485-001

RF input adapter cable 407940-001

TV tuner - ExpressCard 439130-001

TV tuner remote control 408479-001

USB infrared receiver 408483-001

USB travel mouse 435836-001

Wireless laser mouse 430958-001



Antenna adapter - DVB-T 412176-001

Carrying case 418162-001

Wired optical mouse 436238-001

Power cords

For use with all computer models in the following countries or regions::

Australia and New Zealand 394279-011

Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and Sweden

394279-021

Canada, French Canada, Latin America, Thailand, and the United States

394279-001

Denmark 394279-081

Israel 394279-BB1

Italy 394279-061

Switzerland 394279-111

The United Kingdom and Hong Kong 394279-031


Japan 394279-291

The People’s Republic of China 394279-AA1

Taiwan 394279-AB1


India 394279-D61

Korea 394279-AD1

Table 3-5

Spare Parts: Miscellaneous (Continued)




Screw Kits (include the screws listed below; refer to Appendix A, “Screw Listing,” for more information on screw specifications and usage)

For use only with computer models using Intel processors 434983-001

For use only with computer models using AMD processors 431433-001

■ Phillips PM3.0×3.0 screw





■ Phillips PM2.0×6.0 Screw■ Phillips PM2.0×5.0 captive screw



Table 3-5

Spare Parts: Miscellaneous (Continued)




3.7 Sequential Part Number Listing

Table 3-6

Spare Parts: Sequential Part Number Listing

Spare Part Number Description

364727-001 USB digital drive

371693-001 Headset

394279-001 Power cord for use in Canada, French Canada, Latin America, Thailand, and the United States

394279-011 Power cord for use in Australia

394279-021 Power cord for use in Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and Sweden

394279-031 Power cord for use in the United Kingdom and Hong Kong

394279-061 Power cord for use in Italy

394279-081 Power cord for use in Denmark

394279-111 Power cord for use in Switzerland

394279-291 Power cord for use in Japan only on computer models using Intel processors

394279-AA1 Power cord for use in the People’s Republic of China only on computer models using Intel processors

394279-AD1 Power cord for use in Korea

394279-AB1 Power cord for use in Taiwan

394279-BB1 Power cord for use in Israel

394279-D61 Power cord for use in India only on computer models using AMD processors

402018-001 HP 65W PFC AC Adapter




405527-001 Backpack

407159-001 802.11b/g WLAN Mini Card module for use with all computer models in the MOW countries or regions listed below:

Antigua & Barbuda


The Czech Republic

ChileColumbia


EgyptEl SalvadorEstoniaFinlandFranceGeorgiaGermanyGreeceGuamGuatemalaHong KongHungaryIcelandIndiaIndonesiaIreland

ItalyLatviaLebanonLiechtensteinLithuaniaLuxembourgMalaysiaMaltaMexicoMonacoThe NetherlandsNew ZealandNorwayOmanPanamaParaguayThe PhilippinesPolandPortugalRomania

407159-002 802.11b/g WLAN Mini Card module for use with all computer models in the ROW countries or regions listed below:

ChinaEcuadorHaiti


QatarSouth Korea

Table 3-6

Spare Parts: Sequential Part Number Listing (Continued)




407159-291 802.11b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan

407160-001 802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the MOW countries or regions listed below:

Antigua & Barbuda


The Czech Republic

ChileColumbia


EgyptEl SalvadorEstoniaFinlandFranceGeorgiaGermanyGreeceGuamGuatemalaHong KongHungaryIcelandIndiaIndonesiaIreland

ItalyLatviaLebanonLiechtensteinLithuaniaLuxembourgMalaysiaMaltaMexicoMonacoThe NetherlandsNew ZealandNorwayOmanPanamaParaguayThe PhilippinesPolandPortugalRomania

Table 3-6





407160-002 802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the ROW countries or regions listed below:

ChinaEcuadorHaiti


QatarSouth Korea

407313-001 HP Remote Control

407674-001 802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the MOW1 countries or regions listed below:

Antigua & Barbuda

ArgentinaAustraliaBahamasBarbadosBruneiCanadaChile

Dominican Republic

GuamGuatemalaHong KongPanamaIndiaIndonesia

MalaysiaMexicoNew ZealandParaguaySaudi ArabiaTaiwanThe United StatesVietnam

Table 3-6






ArubaAustriaAzerbaijanBahrainBelgiumBermudaBulgariaCayman IslandsColumbiaCroatiaCyprusThe Czech Republic

DenmarkEgyptEl SalvadorEstoniaFinlandFrance

GeorgiaGermanyGreeceHungaryIcelandIrelandItalyLatviaLebanonThe PhilippinesPolandPortugalRomaniaRussiaSerbia and Montenegro

SingaporeSlovakia

LiechtensteinLithuaniaLuxembourgMaltaMonacoThe NetherlandsNorwayOmanSloveniaSouth AfricaSpainSri LankaSwedenSwitzerlandTurkeyThe United Kingdom

Uzbekistan


ChinaEcuadorHaiti


QatarSouth Korea

Table 3-6





407674-004 802.11b/g WLAN Mini Card module for use in Costa Rica, Israel, Kuwait, Thailand, UAE, Ukraine.

407674-291 802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan

407939-001 Composite S-Video and audio input cable

407940-001 RF input adapter cable

407941-001 Analog TV tuner

408479-001 TV tuner remote control

408483-001 USB infrared receiver

408485-001 RF cable

412175-001 DVB-T TV tuner

412766-002 Bluetooth module (includes Bluetooth module cable)

418162-001 Carrying case

430896-001 Intel Core Duo T1350 (1.86-GHz) processor


430898-001 Intel Core Duo T2050 (1.1.60-GHz) processor

430958-001 Wireless laser mouse

431364-001 System board for use only with full-featured computer models using AMD processors

431365-001 System board for use only with defeatured computer models using AMD processors

431371-001 AMD Turion ML-50 1.60-GHz processor (includes thermal pad)

Table 3-6






431374-001 Mobile AMD Sempron 3200+ 1.60-GHz processor (includes thermal pad)


431386-001 15.4-inch, WXGA, SVA display panel with BrightView for use only with computers using AMD processors

431387-001 15.4-inch, WXGA, SVA AntiGlare display panel for use only with computers using AMD processors

431390-001 Display enclosure for use with full-featured computer models

431391-001 Display inverter

431393-001 Microphone (includes microphone receivers and cables)

431398-001 Wireless antenna transceivers and cables for use only with computers using AMD processors

431400-001 Display Screw Kit (includes screws and rubber screw covers)

431401-001 256-MB memory module for use only with computers using AMD processors (PC2-5300, 667-MHz, 1-DIMM)



431404-001 60-GB hard drive (5400-rpm, includes bracket and connector)



Table 3-6






431411-001 DVD/CD-RW Combo Drive

431412-001 DVD±RW/R and CD-RW Double-Layer Combo Drive

431413-001 DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe

431424-001 Switch cover for use with defeatured computer models (includes LED board and LED board cable)

431425-001 Switch cover for use with full-featured computer models (includes LED board and LED board cable)

431427-001 Base enclosure for use with full-featured computer models (includes wireless switch)

431431-001 Rubber Feet Kit (includes computer feet, not illustrated)

431433-001 Screw Kit for use only with computer models using AMD processors

431435-001 Logo Kit

431436-001 RTC battery (includes 2-sided tape)

431438-001 Power button board (includes power button board cable)

431440-001 ExpressCard assembly

431443-001 Audio board for use with full-featured computer models (includes infrared lens)

Table 3-6





431444-001 Audio board for use with defeatured computer models (does not include infrared lens)

431445-001 USB/power connector board for use with 65W AC adapters (includes USB/power connector board cable)

431446-001 USB/power connector board for use with 90W AC adapters (includes USB/power connector board cable)

431450-001 Fan/heat sink assembly for use only with computer models using AMD processors (includes thermal pads)

432302-001 15.4-inch, WXGA, TFT display assembly with BrightView for use with defeatured computer models (includes wireless antenna transceivers and cables; does not include microphones)

432303-001 15.4-inch, WXGA, TFT Antiglare display assembly for use with defeatured computer models (includes wireless antenna transceivers and cables; does not include microphones)

432304-001 15.4-inch, WXGA, TFT display assembly with BrightView for use with full-featured computer models (includes microphones and wireless antenna transceivers and cables)

432305-001 15.4-inch, WXGA, TFT Antiglare display assembly for use with full-featured computer models (includes microphones and wireless antenna transceivers and cables)

432306-001 6-cell, 4.0-Ahr battery

432307-001 12-cell, 8.8-Ahr battery

432309-001 HP 90W PFC AC Adapter

432310-001 HP 90W non-PFC AC Adapter

432920-001 Display enclosure for use with defeatured computer models

432922-001 Base enclosure for use with defeatured computer models (includes wireless switch)

Table 3-6





433283-001 Display bezel for use with full-featured computer models (includes microphone openings)

433284-001 Display bezel for use with defeatured computer models (does not include microphone openings)

433287-001 Display Cable Kit

433288-001 Display Hinge Kit (includes left and right display hinges)


434415-001 40-GB hard drive for use only with computer models using AMD processors (5400-rpm, includes bracket and connector)

434725-001 945GM system board for use only with full-featured computer models using Intel processors

434726-001 940GML system board for use only with defeatured computer models using Intel processors



434735-001 Intel Celeron 420 (1.6-GHz) processor

434740-001 256-MB memory module for use only with computer models using Intel processors (PC2-5300, 667-MHz, 1-DIMM)



434743-001 40-GB hard drive for use only with computer models using Intel processors (5400-rpm, includes bracket and connector)

434746-001 Fan/heat sink assembly for use only with computer models using Intel processors (includes thermal paste)

Table 3-6





434983-001 Screw Kit for use only with computer models using Intel processors

434984-001 Cable Kit

435743-001 HP Remote Control Ii Plus

435836-001 USB travel mouse

436156-001 Hard Drive Bracket Kit


436159-001 Intel Celeron 430 (1.73-GHz) processor

436238-001 Wired optical mouse


436900-001 Intel Core Duo T5200 (1.66-GHz) processor, for use with V6200 models

438186-001 Top cover for use with full-featured computer models (includes speakers, TouchPad, and TouchPad cable)

438187-001 Top cover for use with defeatured computer models (includes speaker, TouchPad, and TouchPad cable)

438316-001 Base enclosure for use with defeatured computer models (includes wireless switch)


438669-001 Plastics Kit

439128-001 Remote control, ExpressCard

439129-001 Infrared emitter

439130-001 TV tuner

439131-001 TV tuner antenna

Table 3-6





439254-001 Remote control - ExpressCard (EMEA)

441424-001 200-GB hard drive (4200-rpm, includes bracket & connector)

441428-001 Keyboard for use in the United States

441428-031 Keyboard for use in the United Kingdom

441428-051 Keyboard for use in France

441428-061 Keyboard for use in Italy

441428-071 Keyboard for use in Spain

441428-121 Keyboard for use in French Canada

441428-161 Keyboard for use in Latin America only on computer models using Intel processors

441428-171 Keyboard for use in Saudi Arabia only on computer models using Intel processors

441428-281 Keyboard for use in Thailand only on computer models using Intel processors

441428-331 Keyboard for use in the Netherlands

441428-AB1 Keyboard for use in Taiwan only on computer models using Intel processors

441428-AD1 Keyboard for use in the Korea

441428-DH1 Keyboard for use only on computer models using AMD processors in Denmark, Finland, Norway, and Sweden

441677-001 945PM system board - EMEA (for Germany only)

441761-001 Intel Celeron 440 (1.86-GHz) processor, for use with V6200 models

Table 3-6






444479-001 943GM system board - for use only with defeatured models

Table 3-6



4Removal and Replacement

Preliminaries

This chapter provides essential information for proper and safe removal and replacement service.

4.1 Tools RequiredYou will need the following tools to complete the removal and replacement procedures:■ Magnetic screwdriver■ Phillips P0 and P1 screwdrivers■ Flat-bladed screwdriver


Removal and Replacement Preliminaries

4.2 Service ConsiderationsThe following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures.

✎ As you remove each subassembly from the computer, place the subassembly (and all accompanying screws) away from the work area to prevent damage.

Plastic Parts

Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.

Cables and Connectors

ÄCAUTION: When servicing the computer, ensure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer.

Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Ensure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.



4.3 Preventing Damage to Removable DrivesRemovable drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a removable drive, or loss of information, observe the following precautions:■ Before removing or inserting a hard drive, shut down the

computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system.

■ Before removing a diskette drive or optical drive, ensure that a diskette or disc is not in the drive and ensure that the optical drive tray is closed.

■ Before handling a drive, ensure that you are discharged of static electricity. While handling a drive, avoid touching the connector.

■ Handle drives on surfaces covered with at least one inch of shock-proof foam.

■ Avoid dropping drives from any height onto any surface.■ After removing a hard drive, CD-ROM drive, or a diskette

drive, place it in a static-proof bag.■ Avoid exposing a hard drive to products that have magnetic

fields, such as monitors or speakers.■ Avoid exposing a drive to temperature extremes or liquids.■ If a drive must be mailed, place the drive in a bubble pack

mailer or other suitable form of protective packaging and label the package, “FRAGILE: Handle With Care.”



4.4 Preventing Electrostatic DamageMany electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.

A sudden discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry. Often the spark is neither felt nor heard, but damage occurs.

An electronic device exposed to electrostatic discharge might not be affected at all and can work perfectly throughout a normal cycle. Or the device might function normally for a while, then degrade in the internal layers, reducing its life expectancy.



4.5 Packaging and Transporting PrecautionsUse the following grounding precautions when packaging and transporting equipment:■ To avoid hand contact, transport products in static-safe

containers, such as tubes, bags, or boxes.■ Protect all electrostatic-sensitive parts and assemblies with

conductive or approved containers or packaging.■ Keep electrostatic-sensitive parts in their containers until

the parts arrive at static-free workstations.■ Place items on a grounded surface before removing items

from their containers.■ Always be properly grounded when touching a sensitive

component or assembly.■ Store reusable electrostatic-sensitive parts from assemblies

in protective packaging or nonconductive foam.■ Use transporters and conveyors made of antistatic belts and

roller bushings. Ensure that mechanized equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.



4.6 Workstation PrecautionsUse the following grounding precautions at workstations:■ Cover the workstation with approved static-shielding material

(refer to Table 4-2, “Static-Shielding Materials”).■ Use a wrist strap connected to a properly grounded work

surface and use properly grounded tools and equipment.■ Use conductive field service tools, such as cutters,

screwdrivers, and vacuums.■ When using fixtures that must directly contact dissipative

surfaces, only use fixtures made of static-safe materials.■ Keep the work area free of nonconductive materials, such

as ordinary plastic assembly aids and Styrofoam.■ Handle electrostatic-sensitive components, parts, and

assemblies by the case or PCM laminate. Handle these items only at static-free workstations.

■ Avoid contact with pins, leads, or circuitry.■ Turn off power and input signals before inserting or removing

connectors or test equipment.



4.7 Grounding Equipment and MethodsGrounding equipment must include either a wrist strap or a foot strap at a grounded workstation.■ When seated, wear a wrist strap connected to a grounded

system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.

■ When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at standing workstations and are compatible with most types of shoes or boots. On conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the operator and ground. To be effective, the conductive strips must be worn in contact with the skin.

Other grounding equipment recommended for use in preventing electrostatic damage includes■ Antistatic tape.■ Antistatic smocks, aprons, and sleeve protectors.■ Conductive bins and other assembly or soldering aids.■ Nonconductive foam.■ Conductive tabletop workstations with ground cords of

one megohm resistance.■ Static-dissipative tables or floor mats with hard ties to

the ground.■ Field service kits.■ Static awareness labels.■ Material-handling packages.■ Nonconductive plastic bags, tubes, or boxes.■ Metal tote boxes.■ Electrostatic voltage levels and protective materials.



Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.

Table 4-2 lists the shielding protection provided by antistatic bags and floor mats.

Table 4-1

Typical Electrostatic Voltage Levels

Relative Humidity

Event 10% 40% 55%

Walking across carpet 35,000 V 15,000 V 7,500 V

Walking across vinyl floor 12,000 V 5,000 V 3,000 V

Motions of bench worker 6,000 V 800 V 400 V

Removing DIPS from plastic tube 2,000 V 700 V 400 V

Removing DIPS from vinyl tray 11,500 V 4,000 V 2,000 V

Removing DIPS from Styrofoam 14,500 V 5,000 V 3,500 V

Removing bubble pack from PCB 26,500 V 20,000 V 7,000 V

Packing PCBs in foam-lined box 21,000 V 11,000 V 5,000 V

✎ A product can be degraded by as little as 700 V.

Table 4-2

Static-Shielding Materials

Material Use Voltage Protection Level

Antistatic plastic Bags 1,500 V

Carbon-loaded plastic Floor mats 7,500 V

Metallized laminate Floor mats 5,000 V


5Removal and Replacement

Procedures

This chapter provides removal and replacement procedures.

There are as many as 84 screws, in 9 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.

Refer to Appendix A, “Screw Listing,” for detailed information on screw sizes, locations, and usage.


Removal and Replacement Procedures

5.1 Serial NumberReport the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer.

Serial Number Location



5.2 Disassembly Sequence ChartUse the chart below to determine the section number to be referenced when removing computer components.

Disassembly Sequence Chart

Section Description # of Screws Removed

5.3 Preparing the Computer For Disassembly

Battery 0

5.4 Hard Drive 2 loosened to remove the hard drive cover6 removed to disassemble the hard drive

5.5 Computer Feet 0

5.6 Memory Module 3 loosened to remove the memory module compartment cover

5.7 RTC Battery 0

5.8 Mini Card Module 2

Ä To prevent an unresponsive system and the display of a warning message, install only a Mini Card device authorized for use in your computer by the governmental agency that regulates wireless devices in your country or region. If you install a device and then receive a warning message, remove the device to restore computer functionality. Then contact technical support by selecting Start > Help and Support > Contact support.

5.9 Optical Drive 1 to remove the optical drive2 to remove the optical drive bracket

5.10 Switch Cover 2 to remove the switch cover1 to remove the num lock board

5.11 Keyboard 3



5.3 Preparing the Computer For DisassemblyBefore you begin any removal or installation procedures:

1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system.

2. Disconnect all external devices connected to the computer.

3. Disconnect the power cord.

Section Description # of Screws Removed

5.12 Power Button Board 1

5.13 Display AssemblyDisplay bezelDisplay inverterDisplay panelDisplay hingesWireless antenna transceiversMicrophones

4804422

5.14 Top Cover 22

5.15 Audio Board 2

5.16 Bluetooth Module 2

5.17 ExpressCard Assembly 4

5.18 USB/Power Connector Board 2

5.19 System Board 2

5.20 Fan/Heat Sink Assembly 4

5.21 Processor 1 loosened

Disassembly Sequence Chart (Continued)



4. Remove the battery by following these steps:

a. Turn the computer upside down with the front panel toward you.

b. Slide and hold the battery release latch 1 to the left. (The front edge of the battery disengages from the computer.)

c. Lift the front edge of the battery 2 and swing it back.

d. Remove the battery.

Removing the Battery

Reverse the above procedure to install the battery.

Battery Spare Part Number Information

12-cell, 8.8-Ahr6-cell, 4.0-Ahr

432307-001432306-001



5.4 Hard Drive

Hard Drive Spare Part Number Information

For use with all computer models

200-GB160-GB120-GB100-GB80-GB60-GB

441424-001438485-001431407-001431406-001431405-001431404-001


434743-001


434415-001

Hard Drive Bracket Kit (includes hard drive bracket and screws used to secure the bracket to the hard drive)

436156-001



1. Prepare the computer for disassembly (refer to Section 5.3).

2. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the hard drive cover to the computer.

3. Lift the right side of the cover 2 and swing it to the left.

4. Remove the hard drive cover.

✎ The hard drive cover is included in the Plastics Kit, spare part number 438669-001.

Removing the Hard Drive Cover



5. Use the mylar tab 1 to lift the hard drive 2 until it disconnects from the computer.

6. Remove the hard drive from the hard drive bay.

Removing the Hard Drive



7. Remove the six Phillips PM3.0×3.0 screws 1 that secure the hard drive bracket to the hard drive.

8. Lift the bracket 2 straight up to remove if from the hard drive.

Removing the Hard Drive Bracket

Reverse the above procedure to install and reassemble the hard drive.



5.5 Computer FeetThe computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Feet Kit, spare part number 431431-001. The feet attach to the base enclosure in the locations illustrated below.

Computer Feet Locations



5.6 Memory Module


Memory Module Spare Part Number Information


1024-MB512-MB256-MB

434742-001434741-001434740-001


1024-MB512-MB256-MB

431403-001431402-001

431401-001



2. Loosen the three Phillips PM2.0×5.0 screws 1 that secure the memory module compartment cover to the computer.

3. Lift the left side of the memory module compartment cover 2, and then swing it to the right.

4. Remove the memory module compartment cover.

✎ The memory module compartment cover is included in the Plastics Kit, spare part number 431429-001.

Removing the Memory Module Compartment Cover



5. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the module opposite the socket rises away from the computer.)

6. Slide the module 2 away from the socket at an angle.

✎ Memory modules are designed with a notch 3 to prevent incorrect installation into the memory module socket.

Removing a Memory Module

Reverse the above procedure to install a memory module.



5.7 RTC Battery


2. Remove the memory module compartment cover(Section 5.6).

3. Disconnect the RTC battery cable 1 from the system board.

4. Remove the RTC battery 2.

✎ The RTC battery is secured to the computer by 2-sided tape. All replacement RTC battery spare part kits include 2-sided tape.

Removing the RTC Battery

Reverse the above procedure to install the RTC battery.

RTC Battery Spare Part Number Information

RTC battery (includes 2-sided tape) 431436-001



5.8 Mini Card Module

Mini Card Module Spare Part Number Information


802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the MOW1 countries or regions listed below:

407674-001

Antigua & Barbuda

ArgentinaAustraliaBahamasBarbadosBrunei

CanadaChileDominican Republic

GuamGuatemalaHong Kong

PanamaIndiaIndonesiaMalaysiaMexicoNew Zealand

ParaguaySaudi ArabiaTaiwanThe United StatesVietnam

802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the MOW2 countries or regions listed below:

407674-002

Aruba

AustriaAzerbaijanBahrain

BelgiumBermudaBulgaria

Cayman IslandsColumbiaCroatia

CyprusThe Czech Republic

Denmark

Egypt

El SalvadorEstoniaFinland

FranceGeorgiaGermany

GreeceHungaryIceland

IrelandItaly

LatviaLebanon

The Philippines

PolandPortugalRomania

RussiaSerbia and Montenegro

SingaporeSlovakia

LiechtensteinLithuania

LuxembourgMaltaMonaco

The Netherlands

NorwayOman

SloveniaSouth AfricaSpain

Sri LankaSwedenSwitzerland

TurkeyThe United

KingdomUzbekistan



802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in the ROW countries or regions listed below:

407674-003

ChinaEcuadorHaiti


QatarSouth Korea

UruguayVenezuela

802.11b/g WLAN Mini Card module for use in Costa Rica, Israel, Kuwait, Thailand, UAE, Ukraine.

407674-004

802.11a/b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan

407674-291

802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the MOW countries or regions listed below:

407160-001

Antigua & Barbuda


The Czech Republic

ChileColumbia


EgyptEl SalvadorEstoniaFinlandFranceGeorgiaGermanyGreeceGuamGuatemalaHong KongHungaryIcelandIndiaIndonesia

IrelandItalyLatviaLebanonLiechtensteinLithuaniaLuxembourgMalaysiaMaltaMexicoMonacoThe NetherlandsNew ZealandNorwayOmanPanamaParaguayThe PhilippinesPolandPortugalRomania

RussiaSaudi ArabiaSerbia and Montenegro

SingaporeSlovakiaSloveniaSouth AfricaSpainSri LankaSwedenSwitzerlandTaiwanTurkeyThe United Kingdom

The United StatesUzbekistanVietnam

Mini Card Module Spare Part Number Information (Continued)



802.11a/b/g WLAN Mini Card module for use only with computer models using AMD processors in the ROW countries or regions listed below:

407160-002

ChinaEcuadorHaiti


QatarSouth Korea

UruguayVenezuela

802.11b/g WLAN Mini Card module for use with all computer models in the MOW countries or regions listed below:

407159-001

Antigua & Barbuda

ArgentinaArubaAustralia

AustriaAzerbaijanBahamas

BahrainBarbadosBelgium

BermudaBruneiBulgaria

CanadaThe Cayman Islands

The Czech Republic

Chile

Columbia

CroatiaCyprusDenmark

The Dominican Republic

EgyptEl SalvadorEstonia

FinlandFranceGeorgia

GermanyGreeceGuam

GuatemalaHong KongHungary

IcelandIndia

Indonesia

IrelandItalyLatvia

LebanonLiechtensteinLithuania

LuxembourgMalaysiaMalta

MexicoMonacoThe Netherlands

New ZealandNorwayOman

PanamaParaguayThe Philippines

PolandPortugal

RomaniaRussiaSaudi Arabia

Serbia and Montenegro

SingaporeSlovakiaSlovenia

South AfricaSpainSri Lanka

SwedenSwitzerlandTaiwan

TurkeyThe United Kingdom

The United States

UzbekistanVietnam




1. Prepare the computer for disassembly (Section 5.3).

2. Remove the memory module compartment cover(Section 5.6).

802.11b/g WLAN Mini Card module for use with all computer models in the ROW countries or regions listed below:

407159-002

ChinaEcuadorHaiti


QatarSouth Korea

UruguayVenezuela

802.11b/g WLAN Mini Card module for use only with computer models using Intel processors in Japan

407159-291




3. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card module before disconnecting the cables. Then disconnect the cables 1 from the module.

4. Remove the two Phillips PM2.0×3.0 screws 2 that secure the Mini Card module to the computer. (The edge of the module opposite the socket rises away from the computer).

5. Remove the module 3 by pulling it away from the socket at an angle.

✎ Mini Card WLAN modules are designed with a notch 4 to prevent incorrect installation into the Mini Card module socket.

Removing a Mini Card Module

Reverse the above procedure to install a Mini Card module.



5.9 Optical Drive


2. Remove the Phillips PM2.5×7.0 screw 1 that secures the optical drive to the computer.

3. Insert a thin tool, such as a paper clip 2, into the media tray release hole. (The optical drive media tray releases from the optical drive.)

4. Use the media tray frame to slide the optical drive 3 out of the computer.

5. Remove the optical drive.

Removing the Optical Drive

Optical Drive Spare Part Number Information


431413-001

431412-001431411-001



6. Position the optical drive with the optical drive bracket toward you.

7. Remove the two Phillips PM2.0×3.0 screws 1 that secure the optical drive bracket to the optical drive.

8. Remove the optical drive 2.

Removing the Optical Drive Bracket

Reverse the above procedure to reassemble and install the optical drive.



5.10 Switch Cover


2. Close the computer.

3. Turn the computer upside down with the front panel toward you.

4. Remove the two Phillips PM2.5×10.0 screws that secure the switch cover to the computer.

Removing the Switch Cover Screws

Switch Cover Spare Part Number Information


431424-001431425-001



5. Turn the computer display-side up with the front toward you.

6. Open the computer as far as possible.

7. Lift the rear edge of the switch cover and swing it forward until it rests on the keyboard.

Releasing the Switch Cover



8. Release the zero insertion force (ZIF) connector 1 to which the LED board cable is connected and disconnect the cable 2 from the LED board.

9. If it is necessary to replace the num lock board, disconnect the num lock board cable 3 from the LED board.

10. Remove the Phillips PM2.0×3.0 screw 4 that secures the num lock board to the switch cover and remove the num lock board 5.

11. Remove the switch cover.

Removing the Num Lock Board

Reverse the above procedure to install the switch cover and num lock board.



5.11 Keyboard


2. Remove the switch cover (Section 5.10).

Keyboard Spare Part Number Information

For use with all computer models in the following countries or regions:

FranceFrench CanadaItaly

The Netherlands

441428-051441428-121441428-061

441428-331

SpainThe United KingdomThe United States

441428-071441428-031441428-001


Latin AmericaSaudi Arabia

441428-161441428-171

TaiwanThailand

441428-AB1441428-281


Denmark, Finland, Norway, and Sweden

441428-DH1 Korea 441428-AD1

For UK OTC ID only 443689-001



3. Remove the three Phillips PM2.5×7.0 screws that secure the keyboard to the computer.

Removing the Keyboard Screws



4. Turn the computer display-side up with the front panel toward you.

5. Open the computer as far as possible.

6. Lift the rear edge of the keyboard 1 until it rests at an angle.

7. Slide the keyboard 2 back to disengage the tabs on the front edge of the keyboard from the top cover.

8. Swing the keyboard 3 forward until it rests on the palm rest.

Releasing the Keyboard



9. Release the ZIF connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board.

Disconnecting the Keyboard Cable

10. Remove the keyboard.

Reverse the above procedure to install the keyboard.



5.12 Power Button Board



3. Remove the keyboard (Section 5.11).

4. Remove the Phillips PM2.0×3.0 screw 1 that secures the power button board to the computer.

5. Release the power button board 2 from the computer as far as the cables will allow.

Releasing the Power Button Board

Power Button Board Spare Part Number Information

Power button board (includes power button board cable) 431438-001



6. Disconnect the microphone cable 1 and the speaker assembly cable 2 from the power button board.

7. Release the ZIF connector 3 to which the power button board cable is connected and disconnect the cable.

8. Remove the power button board 4.

Removing the Power Button Board

Reverse the above procedure to install the power button board.



5.13 Display Assembly


2. Disconnect the Mini Card WLAN antenna cables from the Mini Card WLAN module (Section 5.8).


4. Remove the keyboard (Section 5.11).

Display Assembly Spare Part Number Information

For use with full-featured computer models (includes microphones)


432304-001432305-001

For use with defeatured computer models (does not include microphones)


432302-001432303-001



5. Disconnect the display cable 1 from the system board.

6. Disconnect the microphone cable 2 from the power button board.

7. Remove the wireless antenna cables 3 from the clips in the top cover.

Disconnecting the Display Cables



ÄCAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other computer components.

8. Remove the four Phillips PM2.5×7.0 screws 1 that secure the display assembly to the computer.

9. Remove the display assembly 2.

Removing the Display Assembly



10. Remove the eight rubber screw covers from the display bezel.

✎ There are three different sizes of rubber screw covers on the display bezel:

1 Four covers on the top edge of the bezel

2 Two covers on the lower bezel corners

3 Two covers on the lower-inside edge

The display rubber screw covers are included in the Display Screw Kit, spare part number 431400-001.

Removing the Display Bezel Screw Covers



11. Remove the eight Phillips PM2.5×7.0 screws that secure the display bezel to the display assembly.

Removing the Display Bezel Screws



12. Flex the inside edges of the left and right sides 1 and the top and bottom sides 2 of the display bezel until the bezel disengages from the display enclosure.

13. Remove the display bezel 3.

Removing the Display Bezel

Display Assembly Subcomponents


Display bezels

For use with full-featured computer models (includes microphone openings)For use with defeatured computer models

433283-001

433284-001



14. Remove the inverter 1 from the display enclosure.

15. Disconnect the display cable 2 and the backlight cable 3 from the display inverter.

Removing the Display Inverter



Display inverter 431391-001



16. Remove the four Phillips PM2.5×5.0 screws 1 that secure the display panel to the display enclosure.

17. Remove the display panel 2.

Removing the Display Panel



Display panels

15.4-inch, WXGA, SVA display panel with BrightView15.4-inch, WXGA, SVA display panel AntiGlare

431386-001431387-001



18. Remove the two Phillips PM2.0×3.0 screws 1 that secure each hinge to the display enclosure.

19. Remove the display hinges 2.

Removing the Display Hinges



Display Hinge Kit 433288-001



20. If it is necessary to replace the wireless transceivers and cables, remove the Phillips PM2.0×4.0 screw 1 that secures each transceiver to the display enclosure.

21. Remove the wireless antenna cables from the clips 2 built into the display enclosure.

22. Detach the wireless antenna transceivers 3 from the display enclosure.

23. Remove the wireless antenna cables 4.

Removing the Wireless Antenna Transceivers and Cables



Wireless antenna transceivers and cables 431398-001



24. If it is necessary to replace the microphones and cables, release the retention tabs 1 built into the display enclosure that secure the microphones and cables to the display enclosure.

25. Remove the microphones 2 from the clips in the display enclosure.

26. Remove the microphone cables 3 from the display enclosure.

Removing the Microphones

Reverse the above procedure to reassemble and install the display assembly



Microphone Kit (includes microphone receivers and cables) 431393-001



5.14 Top Cover

1. Prepare the computer for disassembly (Section 5.3) and remove the following components:

❏ Hard drive (Section 5.4)

❏ Memory module compartment cover (Section 5.6)

❏ Optical drive (Section 5.9)

❏ Switch cover (Section 5.10)

❏ Keyboard (Section 5.11)

❏ Display assembly (Section 5.13)

Top Cover Spare Part Number Information

Top covers (include speakers, TouchPad, and TouchPad cable)


438186-001431419-001



2. Turn the computer upside down with the front toward you.

3. Remove the nine Phillips PM2.5×7.0 screws that secure the top cover to the computer.

Removing the Top Cover Screws, Part 1



4. Remove the three Phillips PM2.5×4.0 screws 1 and the six Phillips PM2.5×5.0 screws 2 that secure the top cover to the computer.




5. Turn the computer right-side up with the front toward you.

6. Release and disconnect the following ZIF cables from the system board:

1 Power button board cable

2 LED board cable

3 TouchPad cable

Disconnecting the Top Cover Cables



7. Remove the two Phillips PM2.0×6.0 screws 1 and the two Phillips PM2.5×5.0 screws 2 that secure the top cover to the computer.




8. Lift the front edge of the top cover 1 until it disengages from the computer.

9. Remove the top cover 2.

Removing the Top Cover

Reverse the above procedure to install the top cover.



5.15 Audio Board








❏ Top cover (Section 5.14)

Audio Board Spare Part Number Information

For use with full-featured computer models (includes infrared lens)For use with defeatured computer models (does not include infrared lens)

431443-001

431444-001



2. Remove the two Phillips PM2.5×5.0 screws 1 that secure the audio board to the computer.

3. Slide the audio board 2 back to disengage the audio connectors from the base enclosure.

4. Remove the audio board 3.

5. Disconnect the audio board cable 4 from the audio board.

Removing the Audio Board

Reverse the above procedure to install the audio board.



5.16 Bluetooth Module









Bluetooth Module Spare Part Number Information

Bluetooth module (includes Bluetooth module cable) 412766-002



2. Disconnect the Bluetooth module cable 1 from the system board.

3. Remove the two Phillips PM2.0×3.0 screws 2 that secure the Bluetooth module to the system board.

4. Remove the Bluetooth module 3.

Removing the Bluetooth Module

Reverse the above procedure to install the Bluetooth module.



5.17 ExpressCard Assembly









ExpressCard Assembly Spare Part Number Information

ExpressCard assembly 431440-001



2. Push in on the ExpressCard bezel 1 to release the bezel from the ExpressCard slot.

3. Remove the ExpressCard bezel 2 from the ExpressCard slot.

✎ The ExpressCard bezel is included in the Plastics Kit, spare part number 438669-001.

Removing the ExpressCard Slot Bezel



4. Remove the four Phillips PM2.5×4.0 screws 1 that secure the ExpressCard assembly to the system board.

5. Slide the ExpressCard assembly 2 to the right to disconnect it from the system board.

6. Remove the ExpressCard assembly 3.

Removing the ExpressCard Assembly

Reverse the above procedure to install the ExpressCard assembly.



5.18 USB/Power Connector Board









USB/Power Connector Board Spare Part Number Information

USB/power connector boards (include USB/power connector board cable)

For use with 90-W AC adaptersFor use with 65-W AC adapters

431446-001431445-001



2. Remove the two Phillips PM2.5×5.0 screws 1 that secure the USB/power connector board to the computer.

3. Release the USB/power connector board 2 as far as the USB/power connector board cable will allow.

4. Disconnect the USB board cable 3 and the power connector board cable 4 from the USB/power connector board.

Removing the USB/Power Connector Board

5. Remove the USB/power connector board.

Reverse the above procedure to install the USB/power connector board.



5.19 System Board

✎ When replacing the system board, ensure that the following components are removed from the defective system board and installed on the replacement system board:■ Memory modules (Section 5.6)■ RTC battery (Section 5.7)■ Mini Card module (Section 5.8)■ Bluetooth module (Section 5.16)■ ExpressCard assembly (Section 5.17)■ Fan/heat sink assembly (Section 5.20)■ Processor (Section 5.21)


❏ Hard drive (Section 5.4)❏ Optical drive (Section 5.9)❏ Switch cover (Section 5.10)❏ Keyboard (Section 5.11)❏ Display assembly (Section 5.13)❏ Top cover (Section 5.14)

System Board Spare Part Number Information

945GM - For use only with full-featured computer models using Intel processors940GML - For use only with defeatured computer models using Intel processors943GM - For use only with defeatured computer models945PM - EMEA (Germany) only

434725-001

434726-001

444479-001441677-001

For use only with full-featured computer models using AMD processorsFor use only with defeatured computer models using AMD processors

431364-001

431365-001



❏ Audio board (Section 5.15)❏ USB/power connector board (Section 5.18)

2. Remove the USB/power connector board cable 1 from the clips in the base enclosure.

3. Remove the two Phillips PM2.5×4.0 screws 2 that secure the system board to the base enclosure.

Removing the System Board Screws



4. Use the optical drive connector 1 to lift the right side of the system board 2 until it rests at an angle.

5. Slide the system board 3 to the right until the connectors on the left side of the system board disengage from the base enclosure.

6. Remove the system board.

Removing the System Board



7. If it is necessary to replace the USB/power connector board cable or the audio board cable, turn the system board upside down with the front toward you.

8. Disconnect the USB/power connector board cable 1 and the audio board cable 2 from the system board.

Removing the System Board Cables

Reverse the above procedure to install the system board, USB/power connector board cable, and audio board cable.



5.20 Fan/Heat Sink Assembly

✎ When replacing the fan/heat sink assembly, be sure the power button board is removed from the defective fan/heat sink assembly and installed on the replacement fan/heat sink assembly. Refer to Section 5.12, “Power Button Board,” for power button board removal information.









❏ System board (Section 5.19)

2. Turn the system board upside down with the expansion port 3 and external monitor port toward you.

Fan/Heat Sink Assembly Spare Part Number Information

Fan/heat sink assembly for use only with computer models using AMD processorsFan/heat sink assembly for use only with computer models using Intel processors

431450-001

434746-001



3. Disconnect the fan cable 1 from the system board.

4. Remove the four Phillips PM2.5×5.0 screws 2 that secure the fan/heat sink assembly to the system board.

5. Remove the fan/heat sink assembly 3.

Removing the Fan/Heat Sink Assembly



✎ The thermal pads and thermal paste should be thoroughly cleaned from the surfaces of the fan/heat sink assembly 1, 2, and 3, the system board components 4 and 6, and the processor 5 each time the fan/heat sink assembly is removed. Thermal pads and thermal paste should be installed on all surfaces before the fan/heat sink assembly is reinstalled. Thermal pads and thermal paste are included with all fan/heat sink assembly, system board, and processor spare part kits.

Thermal Pad and Thermal Paste Locations

Reverse the above procedure to install the fan/heat sink assembly.



5.21 Processor

Processor Spare Part Number Information

Intel Core Duo T7200 (2.00-GHz)Intel Core Duo T1350 (1.86-GHz)Intel Core Duo T5600 (1.83-GHz)Intel Core Duo T2350 (1.60-GHz), for use with V6200 modelsIntel Core Duo T2250 (1.73-GHz)Intel Core Duo T5500 (1.66-GHz)Intel Core Duo T5200 (1.66-GHz), for use with V6200 modelsIntel Core Duo T2060 (1.60-GHz), for use with V6200 modelsIntel Core Duo T2050 (1.60-GHz)

434730-001430896-001434731-001441762-001430897-001436157-001436900-001441763-001430898-001

Intel Celeron 440 (1.86-GHz), for use with V6200 modelsIntel Celeron 430 (1.73-GHz)Intel Celeron 420 (1.60-GHz)

441761-001436159-001434735-001

AMD Turion ML-60 (2.0-GHz)AMD Turion ML-56 (1.8-GHz)AMD Turion ML-52 (1.6-GHz)AMD Turion ML-50 (1.6-GHz)

436257-001431373-001431372-001431371-001

Mobile AMD Sempron 3500+ (1.8-GHz)Mobile AMD Sempron 3400+ (1.8-GHz)Mobile AMD Sempron 3200+ (1.6-GHz)

434414-001431375-001431374-001











❏ System board (Section 5.19)

❏ Fan/heat sink assembly (Section 5.20)



2. Turn the processor locking screw 1 one-half turn counterclockwise until you hear a click.

3. Lift the processor 2 straight up and remove it.

✎ The gold triangle 3 on the processor should be aligned with the triangle icon 4 embossed on the processor socket when you install the processor.

Removing the Processor

Reverse the above procedure to install the processor.


6Specifications

This chapter provides physical and performance specifications.

Table 6-1

Computer

Dimensions

LengthWidthHeight (varies front to rear)

35.7 cm25.7 cm4.1 cm

14.05 in10.12 in1.57 in

Weight (varies by configuration) 2.7 kg 5.8 lb

Stand-alone power requirements

Operating voltageOperating current

18.5 V dc —19.0 V dc3.5 A or 4.74 A

Temperature

Operating*Nonoperating

5°C to 35°C-20°C to 60°C

41°F to 95°F-4°F to 140°F

Relative humidity (noncondensing)

OperatingNonoperating

10% to 90%5% to 95%, 38.7°C (101.6°F) maximum wet bulb temperature

Maximum altitude (unpressurized)

Operating (14.7 to 10.1 psia)Nonoperating (14.7 to 4.4 psia)

-15 m to 3,048 m-15 m to 12,192 m

-50 ft to 10,000 ft-50 ft to 40,000 ft


Specifications

Shock


125 g, 2 ms, half-sine200 g, 2 ms, half-sine

Random Vibration

Operating

Nonoperating

0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate

*Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures.

Table 6-1

Computer (Continued)


Specifications

Table 6-2

15.4-inch, WXGA, SVA Display

Dimensions

HeightWidthDiagonal

20.7 cm33.1 cm39.1 cm

8.15 in13.03 in15.39 in

Number of colors Up to 16.8 million

Contrast ratio 200:1

Brightness 160 nits typical

Pixel resolution

PitchFormatConfiguration

0.259 × 0.259 mm1280 × 800RGB vertical stripe

Backlight Edge lit

Character display 80 × 25

Total power consumption 4 W

Viewing angle +/-65° horizontal, +/-50° vertical typical


Specifications

Table 6-3

Hard Drives

200-GB* 160-GB*

Dimensions

HeightWidthWeight

9.5 mm70 mm99 g

9.5 mm70 mm102 g

Interface type ATA-7 ATA-7

Transfer rate

Synchronous (maximum)Security

150 MB/secATA security


Seek times (typical read, including setting)

Single trackAverageMaximum

2 ms12ms22 ms

2 ms12 ms21 ms

Logical blocks† 390,721,968 312,581,808

Disk rotational speed 4200 rpm 5400 rpm

Operating temperature 0°C to 60°C (32°F to 140°F)

5°C to 60°C (41°F to 140°F)

✎ Certain restrictions and exclusions apply. For details, consult technical support by selecting Start > Help and Support > Contact support.

*1 GB = 1 billion bytes when referring to hard drive storage capacity. Accessible capacity is less. Actual drive specifications may differ slightly.


Specifications

120-GB* 100-GB*

Dimensions

HeightWidthWeight

9.5 mm70 mm102 g

9.5 mm70 mm102 g

Interface type ATA-5 ATA-5

Transfer rate






3 ms13 ms24 ms

3 ms13 ms24 ms

Logical blocks† 234,433,260 195,364,233

Disk rotational speed 5400 rpm




Table 6-3

Hard Drives (Continued)


Specifications

80-GB* 60-GB* 40-GB*

Dimensions

HeightWidthWeight

9.5 mm70 mm99 g

9.5 mm70 mm99 g

9.5 mm70 mm99 g

Interface type ATA-5 ATA-5 ATA-5

Transfer rate


100 MB/sec

ATA security

100 MB/sec

ATA security

100 MB/sec

ATA security



3 ms13 ms24 ms

3 ms13 ms24 ms

3 ms13 ms24 ms

Logical blocks† 156,301,488 117,210,240 78,140,160

Disk rotational speed 5400 rpm




Table 6-3

Hard Drives (Continued)


Specifications

Table 6-4

Primary 6-cell, Li-Ion Battery

Dimensions

HeightWidthDepthWeight

2.00 cm9.40 cm13.40 cm0.34 kg

0.79 in3.70 in5.28 in0.75 lb

Energy

VoltageAmp-hour capacityWatt-hour capacity

11.1 V4.4 Ah48 Wh

Temperature


5°C to 45°C0°C to 60°C

41°F to 113°F32°F to 140°F


Specifications

Table 6-5

DVD/CD-RW Combo Drive

Applicable disc Read:DVD-R, DVD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18),CD-ROM (Mode 1 and 2)CD Digital AudioCD-XA ready (Mode 2, Form 1 and 2)CD-I ready (Mode 2, Form 1 and 2)CD-R, CD-RWPhoto CD (single and multisession)CD-Bridge

Write:CD-R and CD-RW

Center hole diameter 1.5 cm (0.59 in)

Disc diameter

Standard discMini disc

12 cm (4.72 in)8 cm (3.15 in)


Specifications

Disc thickness 1.2 mm (0.047 in)

Track pitch 0.74 µm

Access time CD media DVD media

RandomFull stroke

< 110 ms< 210 ms

< 130 ms< 225 ms

Audio output level Line-out, 0.7 V rms

Cache buffer 2 MB

Data transfer rate

CD-R (24X)CD-RW (10X)CD-ROM (24X)DVD (8X)Multiword DMA mode 2

3600 KB/s (150 KB/s at 1X CD rate)1500 KB/s (150 KB/s at 1X CD rate)3600 KB/s (150 KB/s at 1X CD rate)10,800 KB/s (1352 KB/s at 1X DVD rate)16.6 MB/s

Startup time < 15 seconds

Stop time < 6 seconds

Table 6-5

DVD/CD-RW Combo Drive (Continued)


Specifications

Table 6-6

DVD±RW/R and

CD-RW Double-Layer Combo Drive

Applicable disc Read:DVD-R, DVD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18),CD-ROM (Mode 1 and 2)CD Digital AudioCD-XA ready (Mode 2, Form 1 and 2)CD-I ready (Mode 2, Form 1 and 2)CD-R, CD-RWPhoto CD (single and multisession)CD-Bridge

Write:CD-R and CD-RWDVD-R and DVD-RW

Center hole diameter 1.5 cm (0.59 in)

Disc diameter

Standard discMini disc

12 cm (4.72 in)8 cm (3.15 in)


Specifications

Disc thickness 1.2 mm (0.047 in)

Track pitch 0.74 µm

Access time CD media DVD media

RandomFull stroke

< 175 ms< 285 ms

< 230 ms< 335 ms

Audio output level Audio-out, 0.7 Vrms

Cache buffer 2 MB

Data transfer rate

CD-R (16X)CD-RW (8X)CD-ROM (24X)DVD (8X)DVD-R (4X)DVD-RW (2X)Multiword DMA mode 2

2,400 KB/s (150 KB/s at 1X CD rate)1,200 KB/s (150 KB/s at 1X CD rate)3,600 KB/s (150 KB/s at 1X CD rate)10,800 KB/s (1,352 KB/s at 1X DVD rate)5,400 KB/s (1,352 KB/s at 1X DVD rate)2,700 KB/s (1,352 KB/s at 1X DVD rate)16.6 MB/s

Startup time < 15 seconds

Stop time < 6 seconds

Table 6-6

DVD±RW/R and

CD-RW Double-Layer Combo Drive (Continued)


Specifications

Table 6-7

System DMA

Hardware DMA System Function

DMA0 Not applicable

DMA1 Not applicable

DMA2 Not applicable

DMA3 Not applicable

DMA4 Direct memory access controller

DMA5 Available for ExpressCard

DMA6 Not assigned

DMA7 Not assigned


Specifications

Table 6-8

System Interrupts

Hardware IRQ System Function

IRQ0 System timer

IRQ1 Quick Launch buttons

IRQ2 Cascaded

IRQ3 USB2 Enhanced Host Controller—24CD

IRQ4 COM1

IRQ5* Conexant AC—Link AudioSMBus Controller—24C3Data Fax Modem with SmartCP

IRQ6 Diskette drive

IRQ7* Parallel port

IRQ8 System CMOS/real-time clock

IRQ9* Microsoft ACPI-compliant system

IRQ10* USB UHCI controller—24C2GM/GME Graphic ControllerRealtek RTL8139 Family PCI fast Ethernet Controller

IRQ11 USB EHCI controller—24CDUSB UHCI controller—24C4USB UHCI controller—24C7Pro/Wireless 2200BGTI OHCI 1394 host controllerTI PCI1410 CardBus controller

*Default configuration

✎ ExpressCard may assert IRQ3, IRQ4, IRQ5, IRQ7, or IRQ20.


Specifications

Hardware IRQ System Function

IRQ12 Synaptics PS/2 port pointing device

IRQ13 Numeric data processor

IRQ14 Primary IDE channel

IRQ15 Secondary IDE channel

IRQ17 Conexant AC -Link Audio

IRQ17 Soft V90 Data Fax Modem with SmartCP

IRQ17 ATi Mobility Radeon Xpress 200 Series

IRQ19 Standard Enhanced PCI to USB Host Controller

IRQ19 Standard OpenHCD USB Host Controller

IRQ19 Standard OpenHCD USB Host Controller

IRQ20 TI 6411 PCIxx21/x515 Cardbus Controller

IRQ20 TI OHCI Compliant IEEE 1394 Host Controller

IRQ21 TI Integrated PCIxx21 FlashMedia Controller

IRQ21 Broadcom 802.11b/g WLAN

IRQ21 Microsoft ACPI-compliant system

IRQ22 Realtek RTL8100CL Family PCI fast Ethernet Controller

IRQ23 SDA Standard Compliant SD Host Controller

*Default configuration

✎ ExpressCard may assert IRQ3, IRQ4, IRQ5, IRQ7, or IRQ20.

Table 6-8

System Interrupts (Continued)


Specifications

Table 6-9

System I/O Addresses

I/O Address (hex) System Function (shipping configuration)

0x00000000-0x00000CF7 PCI bus

0x00000000-0x00000CF7 Direct memory access controller

0x00000020-0x00000021 Programmable interrupt controller

0x0000002E-0x0000002F System board resources

0x00000040-0x00000043 System timer

0x00000060-0x00000060 Quick Launch Buttons

0x00000061-0x00000061 System speaker

0x00000062-0x00000062 Microsoft ACPI-Compliant Embedded Controller

0x00000064-0x00000064 Quick Launch Buttons

0x00000066-0x00000066 Microsoft ACPI-Compliant Embedded Controller

0x00000070-0x00000071 System CMOS/real time clock

0x00000072-0x00000073 System board resources

0x00000080-0x0000008F Direct memory access controller


0x000000A0-0x000000A1 Programmable interrupt controller

0x000000B0-0x000000B1 System board resources

0x000000C0-0x000000DF Direct memory access controller

0x000000F0-0x000000FE Numeric data processor

0x00000170-0x00000177 Secondary IDE Channel


Specifications


0x000001F0-0x000001F7 Primary IDE Channel

0x00000220-0x0000022F System board resources

0x00000274-0x00000277 ISAPNP Read Data Port

0x00000279-0x00000279 ISAPNP Read Data Port


0x00000376-0x00000376 Secondary IDE Channel

0x000003B0-0x000003BB PCI standard PCI-to-PCI bridge

0x000003B0-0x000003BB ATI MOBILITY RADEON Xpress 200 Series

0x000003C0-0x000003DF PCI standard PCI-to-PCI bridge

0x000003C0-0x000003DF ATI MOBILITY RADEON Xpress 200 Series

0x000003F6-0x000003F6 Primary IDE Channel

0x0000040B-0x0000040B System board resources

0x000004D0-0x000004D1 System board resources

0x000004D6-0x000004D6 System board resources



0x00000A79-0x00000A79 ISAPNP Read Data Port

0x00000C00-0x00000C01 System board resources



0x00000C6C-0x00000C6C System board resources

Table 6-9

System I/O Addresses (Continued)


Specifications


0x00000C6F-0x00000C6F System board resources

0x00000CD4-0x00000CD5 System board resources

0x00000CD6-0x00000CD7 System board resources

0x00000CD8-0x00000CDF System board resources

0x00000D00-0x0000FFFF PCI bus

0x00000F40-0x00000F47 System board resources



0x00008100-0x000081FF System board resources

0x00008400-0x0000840F ATI SMBus

0x00008410-0x0000841F Standard Dual Channel PCI IDE Controller

0x00009000-0x00009FFF PCI standard PCI-to-PCI bridge

0x00009000-0x00009FFF ATI MOBILITY RADEON Xpress 200 Series

0x0000A000-0x0000A0FF Realtek RTL8139/810x Family Fast Ethernet NIC

0x0000F000-0x0000FFFF PCI standard PCI-to-PCI bridge

0x0000FD00-0x0000FDFF Texas Instruments PCIxx21/x515 Cardbus Controller

0x0000FE00-0x0000FEFF Texas Instruments PCIxx21/x515 Cardbus Controller

Table 6-9

System I/O Addresses (Continued)


Specifications

Table 6-10

System Memory Map

Memory Map Address (hex) System Function (shipping configuration)

0xD4100000-0xD41FFFFF PCI standard PCI-to-PCI bridge

0xD4100000-0xD41FFFFF ATI MOBILITY RADEON Xpress 200 Series

0xD8000000-0xDBFFFFFF PCI standard PCI-to-PCI bridge

0xD8000000-0xDBFFFFFF ATI MOBILITY RADEON Xpress 200 Series

0xFAC00000-0xFEBFFFFF PCI standard PCI-to-PCI bridge

0xF6C00000-0xFABFFFFF PCI standard PCI-to-PCI bridge

0xD4000000-0xD4000FFF Standard OpenHCD USB Host Controller

0xD4001000-0xD4001FFF Standard OpenHCD USB Host Controller

0xD4002000-0xD4002FFF Standard Enhanced PCI to USB Host Controller

0xD4003000-0xD40033FF ATI SMBus

0xFFF80000-0xFFFFFFFF System board

0xE0000000-0xE03FFFFF System board

0xE0000000-0xE03FFFFF System board resources

0x0000-0x0FFF System board

0xD4208000-0xD42087FF Texas Instruments OHCI Compliant IEEE 1394 Host Controller

0xD4200000-0xD4203FFF Texas Instruments OHCI Compliant IEEE 1394 Host Controller

0xD4204000-0xD4205FFF Broadcom 802.11b/g WLAN

0xFFEFF000-0xFFEFFFFF Texas Instruments PCIxx21/x515 Cardbus Controller

0xFFEFE000-0xFFEFEFFF Texas Instruments PCIxx21/x515 Cardbus Controller


Specifications

Memory Map Address (hex) System Function (shipping configuration)

0xF2C00000-0xF6BFFFFF Texas Instruments PCIxx21/x515 Cardbus Controller

0xD4206000-0xD4207FFF Texas Instruments PCIxx21 Integrated FlashMedia Controller

0xD4209000-0xD42090FF SDA Standard Compliant SD Host Controller

0xD4208C00-0xD4208CFF SDA Standard Compliant SD Host Controller

0xD4208800-0xD42088FF SDA Standard Compliant SD Host Controller

0xD4209400-0xD42094FF Realtek RTL8139/810x Family Fast Ethernet NIC

0xD4003400-0xD40034FF Conexant AC-Link Audio

0xD4003800-0xD40038FF SoftV90 Data Fax Modem with SmartCP

0xFEC00000-0xFEC00FFF System board resources

0xFEE00000-0xFEE00FFF System board resources

0xA0000-0xBFFFF PCI bus

0xA0000-0xBFFFF PCI standard PCI-to-PCI bridge

0xA0000-0xBFFFF ATI MOBILITY RADEON Xpress 200 Series

0xD6000-0xD7FFF PCI bus

0xDC000-0xDDFFF PCI bus

0xDD000-0xDDFFF Texas Instruments PCIxx21/x515 Cardbus Controller

0xE0000-0xFFFFF System board

0x40000000-0xFFFFFFFF PCI bus

Table 6-10

System Memory Map (Continued)


AScrew Listing

This appendix provides specification and reference information for the screws used in the computer.

The four Phillips PM3.0×3.0 screws (Table A-1) used to secure the hard drive bracket to the hard drive.

The remainder of the screws listed in this appendix are available in the Screw Kits, spare part numbers 434983-001 (for use with computers using Intel processors) and the Display Screw Kit, spare part number 431400-001.

Maintenance and Service Guide A–1

Screw Listing

Phillips PM3.0×3.0 Screw Locations

Table A-1

Phillips PM3.0×3.0 Screw

Color Qty. Length ThreadHead Width

Silver 6 3.0 mm 3.0 mm 5.0 mm

Where used:6 screws that secure the hard drive bracket to the hard drive (documented in Section 5.4)

mm

A–2 Maintenance and Service Guide

Screw Listing

Phillips PM2.0×5.0 Captive Screw Locations

Table A-2

Phillips PM2.0×5.0 Captive Screw


Black 5 5.0 mm 2.0 mm 5.0 mm

Where used:1 Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C-clips; documented in Section 5.4)2 Three screws that secure the memory module compartment cover to the computer (screws are captured on the cover by C-clips; documented inSection 5.6)

mm


Screw Listing


Table A-3




Where used:2 screws that secure the Mini Card module to the computer (documented in Section 5.8)

mm


Screw Listing


Table A-3

Phillips PM2.0×3.0 Screw (Continued)



Where used:2 screws that secure the optical drive bracket to the optical drive (documented in Section 5.9)

mm


Screw Listing

Phillips PM2.0×3.0 Screw Location

Table A-3




Where used:One screw that secures the num lock board to the switch cover (documented in Section 5.10)

mm


Screw Listing


Table A-3




Where used:One screw that secures the power button board to the computer (documented in Section 5.12)

mm


Screw Listing


Table A-3




Where used:4 screws that secure the display hinges to the display panel (documented in Section 5.13)

mm


Screw Listing


Table A-3




Where used:2 screws that secure the Bluetooth module to the system board (documented in Section 5.16)

mm


Screw Listing


Table A-4



Black 25 7.0 mm 2.5 mm 5.0 mm

Where used:1 One screw that secures the optical drive to the computer (documented in Section 5.9)2 Three screws that secure the keyboard to the computer (documented in Section 5.11)

mm


Screw Listing


Table A-4



Black 25 7.0 mm 2.5 mm 5.0 mm

Where used:4 screws that secure the display assembly to the computer (documented in Section 5.13)

mm


Screw Listing


Table A-4



Black 25 7.0 mm 2.5 mm 5.0 mm

Where used:8 screws that secure the display bezel to the display assembly (documented in Section 5.13)

mm


Screw Listing


Table A-4



Black 25 7.0 mm 2.5 mm 5.0 mm

Where used:9 screws that secure the top cover to the computer (documented inSection 5.14)

mm


Screw Listing


Table A-5



Black 2 10.0 mm 2.5 mm 5.0 mm

Where used:2 screws that secure the switch cover to the computer (documented inSection 5.10)

mm


Screw Listing


Table A-6




Where used:4 screws that secure the display panel to the display enclosure (documented inSection 5.13)

mm


Screw Listing


Table A-6




Where used:6 screws that secure the top cover to the base enclosure (documented inSection 5.14)

mm


Screw Listing


Table A-6




Where used:2 screws that secure the top cover to the base enclosure (documented inSection 5.14)

mm


Screw Listing


Table A-6




Where used:1 Two screws that secure the audio board to the base enclosure (documented in Section 5.15)2 Two screws that secure the USB/power connector board to the base enclosure (documented in Section 5.18)

mm


Screw Listing


Table A-6




Where used:4 screws that secure the fan/heat sink assembly to the system board (documented in Section 5.20)

mm


Screw Listing


Table A-7




Where used:2 screws that secure the wireless antenna transceivers to the display enclosure (documented in Section 5.13)

mm


Screw Listing


Table A-8




Where used:3 screws that secure the top cover to the base enclosure (documented in Section 5.14)

mm


Screw Listing


Table A-8




Where used:1 4 screws that secure the ExpressCard assembly to the system board (documented in Section 5.17)2 2 screws that secure the system board to the computer (documented in Section 5.19)

mm


Screw Listing


Table A-9



Black 2 6.0 mm 2.0 mm 5.0 mm

Where used:2 screws that secure the top cover to the base enclosure (documented in Section 5.14)

mm


BBackup and Recovery in

Windows XP

Recovering System InformationTools provided by the operating system and PC Recovery software are designed to help you with the following tasks for safeguarding your information and restoring it in case of a system failure:

■ Backing up your information regularly to protect your important system files.

■ Making a set of recovery discs (PC Recovery software feature). Recovery discs are used to start up (boot) your computer and restore the operating system and software programs to factory settings in case of system failure or instability.

■ Creating system restore points (operating system feature). System restore points allow you to reverse undesirable changes to your computer by restoring the computer to an earlier state.

■ Recovering a program or driver (PC Recovery software feature). This feature helps you reinstall a program or driver without performing a full system recovery.

■ Performing a full system recovery (PC Recovery software feature). With PC Recovery, you can recover your full factory image if you experience system failure or instability. PC Recovery works from a dedicated recovery partition on the hard drive or from recovery discs you create.

Maintenance and Service Guide B–1

Backup and Recovery in Windows XP

Backing Up Your Information

When to Back Up■ On a regularly scheduled basis

✎ Set reminders to back up your information periodically.

■ Before the computer is repaired or restored

■ Before you add or modify hardware or software

Backup Suggestions■ Create system restore points using Windows XP Professional

System Restore feature.

■ Store personal files in the My Documents folder and back up these folders periodically.

■ Back up templates stored in their associated programs.

■ Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.

The screen shot can be a time saver if you have to reset your preferences.

To copy the screen and paste it into a Word document:

a. Display the screen.

b. Copy the screen:

To copy only the active window, press alt+fn+prt sc.

To copy the entire screen, press fn+prt sc.

c. To paste the copied images into a document, open Word, and then select Edit > Paste.

B–2 Maintenance and Service Guide


Using System Restore PointsWhen you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system.

✎ Recovering to an earlier restore point does not affect data files saved or e-mails created since the last restore point.

You also can create additional restore points to provide increased protection for your system files and settings.

When to Create Restore Points■ Before you add or extensively modify software or hardware.

■ Periodically, whenever the system is performing optimally.

✎ If you revert to a restore point and then change your mind, you can reverse the restoration.

Creating a System Restore Point1. Select Start > Help and Support > System Restore.

The System Restore window opens.

2. Click Create a restore point, and then click Next.

3. Follow the on-screen instructions.



Restoring to a Previous Date and TimeTo revert to a restore point (created at a previous date and time), when the computer was functioning optimally:

1. Select Start > Help and Support > System Restore.


2. Click Restore my computer to an earlier time, and then click Next.


Creating Recovery DiscsPC Recovery Disc Creator creates a set of recovery CDs or DVDs for the computer. Use recovery discs to restore the operating system and software programs to factory settings, in case of system failure or instability.

✎ Handle these discs carefully and keep them in a safe place. The software allows the creation of only one set of recovery discs.

Note the following guidelines before creating recovery discs:

■ You will need high quality CD-R, DVD-R, or DVD+R media (purchased separately).

✎ DVD±RW/R and double-layer DVD±RW are not compatible with the PC Recovery Disc Creator software.

■ The computer must be connected to AC power during this process.

■ Only one set of recovery discs can be created per computer.



■ Number each disc before inserting it into the computer optical drive.

■ If necessary, you can exit the program before you have finished creating the recovery discs. The next time you open PC Recovery Disc Creator, you will be prompted to continue the disc creation process.

To create a set of recovery discs:

1. Select Start > All Programs > System Recovery > PC Recovery Disc Creator.

The PC Recovery Disc Creator tool opens.

2. Click Next.

✎ If you are operating the computer on battery power, you will be prompted to connect to AC power before you can go to the next step.

3. Select the type of disc you want to use and click Next.

✎ The software examines the image and displays the number of blank discs needed to create your recovery discs.

4. Insert the first disc and follow the on-screen instructions to complete the creation of the recovery discs.



Reinstalling Software Programs and DriversIf a program or driver preinstalled at the factory is accidentally erased or is damaged, the Application and Driver Recovery tool allows you to reinstall it.

✎ Software not provided with this computer must be reinstalled from the disc provided by the manufacturer or downloaded from the manufacturer's Web site.

✎ Before reinstalling the program, be sure it is fully uninstalled.

The Application and Driver Recovery tool replaces corrupted system files and reinstalls deleted system files within the program.

■ In most cases, if the program you are reinstalling is still on your computer, the reinstallation process does not affect your personal settings.

■ In all cases, if a program has been deleted from your computer, the reinstallation process reinstalls the program or utility to the factory image but cannot restore your personal settings.

Reinstalling Preinstalled Programs and Drivers

1. Remove the program or driver:

✎ In some cases, drivers are not listed in the Add or Remove Programs list. If the driver is not listed, it does not need to be removed.

a. Select Start > Control Panel > Add or Remove Programs.

b. Click the program or driver you want to remove, and then click Change/Remove.



2. Select Start > All Programs > System Recovery > Application and Driver Recovery.

The Application and Driver Recovery tool opens.

3. Select Application Installation or Driver Installation, and then click Next.

4. Follow the on-screen instructions to complete the program or driver recovery.

5. Restart the computer if prompted.

Reinstalling Programs from Discs1. Insert the disc into the optical drive.

2. When the installation wizard opens, follow the installation instructions on the screen.


Performing a RecoveryPC Recovery software allows you to repair or restore the system if you experience system failure or instability. PC Recovery works from recovery discs that you create or from a dedicated recovery partition on the hard drive.

✎ Microsoft Windows XP has its own built-in repair features, such as System Restore and driver roll-back capabilities. If you have not already tried these features, try them before using PC Recovery.

✎ PC Recovery only recovers software that was preinstalled at the factory. Software not provided with this computer must be reinstalled from the disc provided by the manufacturer or downloaded from the manufacturer's Web site.



Recovering from the Recovery DiscsTo restore the system from the recovery discs:

1. Back up all personal files.

2. Insert the first recovery disc into the optical drive and restart the computer.


Recovering from the Partition on the Hard DriveYou can perform a recovery from the partition on the hard drive from either the Start button or f11.

To restore the system from the partition:

1. Access the PC Recovery tool:

❏ To access PC Recovery from the Start button, select Start > All Programs > System Recovery > PC Recovery.

❏ To access PC Recovery from f11, restart the computer and press f11 while the “Press <F11> for recovery” message is displayed on the screen.

The PC Recovery tool opens.

2. Select PC Recovery and click Next.

The computer restarts and the PC Recovery tool opens.

3. Click OK.

4. Follow the on-screen instructions to complete the system recovery.



If you want to perform a destructive recovery:

✎ A destructive recovery formats the hard drive and restores the computer to its factory state. Select this option only as a last resort.

a. Click Advanced Options on the System Recovery screen.

b. Select Destructive Recovery and follow the on-screen instructions.

Deleting the Recovery Partition on the Hard Drive

The PC Recovery Advanced Options menu provides the option of deleting the recovery partition, which will increase space on the hard drive. Delete the recovery partition only if you have already created recovery discs.

ÄCAUTION: After you create the recovery discs, you can increase space on the hard drive by deleting the recovery partition. However, doing this is not recommended. If you delete this partition, you will lose any information that is on the partition, including the PC Recovery software. Thereafter, you must use the recovery discs to access PC Recovery software.

To delete the recovery partition:

1. If you have not already created recovery discs, create them now.

2. Select Start > All Programs > System Recovery > PC Recovery.

The PC Recovery tool opens.

3. Select PC Recovery and click Next.

The computer restarts and the PC Recovery tools opens.



4. Click OK.

5. At the System Recovery screen, click Advanced Options.

6. Select Delete Recovery Partition (not recommended) and follow the on-screen instructions.

Updating Reinstalled SoftwareAfter you perform a system recovery, connect to the Internet to update all reinstalled software.

To access update links for the operating system and other software provided on your computer:

» Select Start > Help and Support.

To update optional software, follow the instructions provided by the software manufacturer. Some programs include an update feature you can access from a Help button or menu within the program.


CBackup and Recovery in

Windows Vista

Recovering System InformationTools provided by the operating system and Recovery Manager software are designed to help you with the following tasks for safeguarding your information and restoring it in case of a system failure:

■ Back up your information regularly to protect your important system files.

■ Make a set of recovery discs (Recovery Manager software feature). Recovery discs are used to start up (boot) your computer and restore the operating system and software programs to factory settings in case of system failure or instability.

■ Create system restore points (operating system feature). System restore points allow you to reverse undesirable changes to your computer by restoring the computer to an earlier state.

■ Recover a program or driver (Recovery Manager software feature). This feature helps you reinstall a program or driver without performing a full system recovery.

■ Perform a full system recovery (Recovery Manager software feature). With Recovery Manager, you can recover your full factory image if you experience system failure or instability. Recovery Manager works from a dedicated recovery partition on the hard drive or from recovery discs you create.

Maintenance and Service Guide C–1

Backup and Recovery in Windows Vista

Backing up Your Information

When to Back Up■ On a regularly scheduled basis.

✎ Set reminders to back up your information periodically.

■ Before the computer is repaired or restored.

■ Before you add or modify hardware or software.

Backup Suggestions■ Create system restore points using the Windows System

Restore feature.

■ Store personal files in the Documents folder and back up these folders periodically.

■ Back up templates stored in their associated programs.

■ Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.

The screen shot can be a time saver if you have to reset your preferences.

To copy the screen and paste it into a word-processing document:

a. Display the screen.

b. Copy the screen:

To copy only the active window, press alt+fn+prt sc.

To copy the entire screen, press fn+prt sc.

c. Open a word-processing document, and then select Edit > Paste.

C–2 Maintenance and Service Guide


Using System Restore PointsWhen you back up your system, you are creating a system restore point. A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system.

✎ Recovering to an earlier restore point does not affect data files saved or e-mails created since the last restore point.

You also can create additional restore points to provide increased protection for your system files and settings.

When to Create Restore Points■ Before you add or extensively modify software or hardware.

■ Periodically, whenever the system is performing optimally.

✎ If you revert to a restore point and then change your mind, you can reverse the restoration.

Creating a System Restore Point1. Select Start > Control Panel > System and Maintenance >

System.

2. In the left pane, click System protection.

3. Click the System Protection tab.

4. Under Automatic restore points, select the disk for which you want to create a restore point.

5. Click Create.

The System Protection window opens.




Restoring to a Previous Date and TimeTo revert to a restore point (created at a previous date and time), when the computer was functioning optimally, follow these steps:

1. Select Start > Control Panel > System and Maintenance > System.

2. In the left pane, click System protection.

3. Click the System Protection tab.

4. Click the System Restore button, and then click Next.



Creating Recovery DiscsRecovery Manager creates a set of recovery CDs or DVDs for the computer. Use recovery discs to restore the operating system and software programs to factory settings, in case of system failure or instability.

✎ Handle these discs carefully and keep them in a safe place. The software allows the creation of only one set of recovery discs.

Note the following guidelines before creating recovery discs:

■ You will need high quality CD-R, DVD-R, or DVD+R discs (purchased separately).

✎ Formatted DVD±RW discs and DVD±RW double-layer discs are not compatible with the Recovery Manager software.

■ The computer must be connected to AC power during this process.

■ Only one set of recovery discs can be created per computer.

■ Number each disc before inserting it into the computer optical drive.



■ If necessary, you can exit the program before you have finished creating the recovery discs. The next time you open Recovery Manager, you will be prompted to continue the disc creation process.

To create a set of recovery discs:

1. Select Start > All Programs > Recovery Manager > Recovery Manager.

Recovery Manager opens.

2. Click Advanced Options.

✎ If you are operating the computer on battery power, you will be prompted to connect to AC power before you can go to the next step.

3. Click Recovery disc creation, and then click Next.


Reinstalling Software Programs and DriversIf a program or driver preinstalled at the factory is accidentally erased or is damaged, Recovery Manager allows you to reinstall it.

✎ Software not provided with this computer must be reinstalled from the disc provided by the manufacturer or downloaded from the manufacturer's Web site.

✎ Before reinstalling the program, be sure it is fully uninstalled.

Recovery Manager replaces corrupted system files and reinstalls deleted system files within the program.

■ In most cases, if the program you are reinstalling is still on your computer, the reinstallation process does not affect your personal settings.



■ In all cases, if a program has been deleted from your computer, the reinstallation process reinstalls the program or utility to the factory image but cannot restore your personal settings.

Reinstalling Preinstalled Programs and Drivers

1. Remove the program or driver:

✎ In some cases, drivers are not listed in the Programs and Features list. If the driver is not listed, it does not need to be removed.

a. Select Start > Control Panel > Programs > Uninstall a program.

b. Right-click the program or driver you want to remove, and then click Uninstall.

2. Reinstall the program or driver:

a. Select Start > All Programs > Recovery Manager > Recovery Manager.


b. Click Advanced Options.

c. Click either Software program re-installation or Hardware driver re-installation, and then click Next.

d. Follow the on-screen instructions.

e. Restart the computer if prompted.

Reinstalling Programs from Discs1. Insert the disc into the optical drive.

2. When the installation wizard opens, follow the installation instructions on the screen.




Performing a RecoveryRecovery Manager software allows you to repair or restore the system if you experience system failure or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery partition on the hard drive.

✎ Windows has its own built-in repair features, such as System Restore and driver rollback capabilities. If you have not already tried these features, try them before using Recovery Manager.

✎ Recovery Manager only recovers software that was preinstalled at the factory. Software not provided with this computer must be reinstalled from the disc provided by the manufacturer or downloaded from the manufacturer's Web site.

Recovering from the Recovery DiscsTo restore the system from the recovery discs:

1. Back up all personal files.

2. Insert the first recovery disc into the optical drive and restart the computer.


Recovering from the Partition on the Hard DriveYou can perform a recovery from the partition on the hard drive from either the Start button or f11.

To restore the system from the partition, follow these steps:

1. Access Recovery Manager in either of the following ways:

❏ Select Start > All Programs > Recovery Manager > Recovery Manager.



❏ Restart the computer and press f11 while the “Press <F11> for recovery” message is displayed on the screen. Then select Recovery Manager.



3. Click System recovery, and then click Next.


Deleting the Recovery Partition on the Hard Drive

The Recovery Manager Advanced Options menu provides the option of deleting the recovery partition, which will increase space on the hard drive. Delete the recovery partition only if you have already created recovery discs.

ÄCAUTION: After you create the recovery discs, you can increase space on the hard drive by deleting the recovery partition. However, doing this is not recommended. If you delete this partition, you will lose any information that is on the partition, including Recovery Manager software. Thereafter, you must use the recovery discs to access Recovery Manager software.

To delete the recovery partition:

1. If you have not already created recovery discs, create them now.

2. Select Start > All Programs > Recovery Manager > Recovery Manager.



4. Click Remove recovery partition, and then click Next.




Updating Reinstalled SoftwareAfter you perform a system recovery, connect to the Internet to update all reinstalled software.

To access update links for the operating system and other software provided on your computer:

» Select Start > Help and Support.

To update optional software, follow the instructions provided by the software manufacturer. Some programs include an update feature you can access from a Help button or menu within the program.


DDisplay Component Recycling

ÅWARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury.

ÄCAUTION: The procedures in this appendix can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. Careful handling should be exercised when removing these components.

✎ Materials DisposalThis HP product contains mercury in the display assembly backlight and may require special handling at end-of-life.

Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities or visit the Electronic Industries Alliance (EIA) at http://www.eiae.org.

Maintenance and Service Guide D–1

http://www.eiae.org

http://www.eiae.org

http://www.eiae.org

Display Component Recycling

This appendix provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight 1 and the LCD panel 2.

✎ Disassembly procedures differ from one display assembly to another. The procedures provided in this appendix are general disassembly instructions. Specific details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.

Refer to Section 5.13, “Display Assembly,” for display assembly disassembly steps.

D–2 Maintenance and Service Guide


Perform the following steps to disassemble the display assembly:

1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.

Removing the Display Bezel Screw Covers and Screws



2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly.

3. Remove the display bezel 3.

Removing the Display Bezel



4. Disconnect all LCD panel cables 1 from the display inverter board and remove the inverter board 2.

Removing the Display Inverter Board



5. Remove all screws 1 that secure the LCD panel to the display enclosure.

6. Remove the LCD panel 2 from the display enclosure.

Removing the LCD Panel



7. Turn the LCD panel upside down.

8. Remove all screws that secure the LCD panel frame to the LCD panel.

Removing the LCD Panel Frame Screws



9. Use a sharp-edged tool to cut the tape 1 that secures the side of the LCD panel to the LCD panel frame.

10. Remove the LCD panel frame 2 from the display panel.

Removing the LCD Panel Frame



11. Remove the screws 1 that secure the backlight cover to the LCD panel.

12. Lift the top edge of the backlight cover 2 and swing it forward.

13. Remove the backlight cover.

Removing the Backlight Cover



14. Turn the LCD panel right-side up.

15. Remove the backlight cables 1 from the clip 2 in the LCD panel.

Releasing the Backlight Cables



16. Turn the LCD panel upside down.

17. Remove the backlight frame from the LCD panel.

Removing the Backlight Frame



ÅWARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury.

18. Slide the backlight out of the backlight frame.

Removing the Backlight



19. Disconnect the display cable 1 from the LCD panel.

20. Remove the screws 2 that secure the LCD panel to the LCD rear panel.

21. Release the LCD panel 3 from the LCD rear panel.

22. Release the tape 4 that secures the LCD panel to the LCD rear panel.

Releasing the LCD Panel



23. Remove the LCD panel.

Removing the LCD Panel

24. Recycle the backlight and LCD panel.


EConnector Pin Assignments

Table D-1

Universal Serial Bus

Pin Signal Pin Signal

1 +5 VDC 3 Data +

2 Data – 4 Ground

Maintenance and Service Guide E–1

Connector Pin Assignments

Table D-2

RJ-45 (Network)


1 Transmit + 5 Unused

2 Transmit – 6 Receive –

3 Receive + 7 Unused

4 Unused 8 Unused

E–2 Maintenance and Service Guide


Table D-3

S-Video-Out


1 TV-Ground 5 TV-CD

2 TV-CVBS 6 TV-Ground

3 TV-Ground 7 TV-YD

4 TV-Ground



Table D-4

External Monitor


1 Red analog 9 +5 VDC

2 Green analog 10 Ground

3 Blue analog 11 Monitor detect

4 Not connected 12 DDC 2B data

5 Ground 13 Horizontal sync

6 Ground analog 14 Vertical sync

7 Ground analog 15 DDC 2B clock

8 Ground analog



Table D-5

RJ-11 (Modem)


1 Unused 4 Unused

2 Tip 5 Unused

3 Ring 6 Unused



Table D-6

Audio-In (Microphone)


1 Audio signal in 3 Ground

2 Audio signal in

Table D-7

Audio-Out (Headphone)


1 Audio out, left channel 3 Ground

2 Audio out, right channel


FPower Cord Set Requirements

3-Conductor Power Cord SetThe wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC.

The power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.

Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.

Maintenance and Service Guide F–1

Power Cord Set Requirements

General RequirementsThe requirements listed below are applicable to all countries and regions.

■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft).

■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used.

■ The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or 250 V AC, as required by each country or region’s power system.

■ The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer.

F–2 Maintenance and Service Guide


Country/Region-Specific Requirements

3-Conductor Power Cord Set Requirements

Country/Region Accredited Agency Applicable Note Number

Australia EANSW 1

Austria OVE 1

Belgium CEBC 1

Canada CSA 2

Denmark DEMKO 1

Finland FIMKO 1

France UTE 1

Germany VDE 1

Italy IMQ 1

Japan METI 3

✎ NOTES:

1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm²

conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.

Maintenance and Service Guide F–3


Korea ek 4

The Netherlands keMa 1

Norway NEMKO 1

People’s Republic of China

ccc 5

Sweden SEMKO 1

Switzerland SEV 1

Taiwan bsmi 4

United Kingdom BSI 1

United States UL 2

✎ NOTES:

1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm²

conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.

4. The flexible cord must be Type RVV, 3-conductor, 0.75 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

5. The flexible cord must be Type VCTF, 3-conductor, 0.75 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

3-Conductor Power Cord Set Requirements (Continued)

Country/Region Accredited Agency Applicable Note Number

F–4 Maintenance and Service Guide

Index

Index

1394 port 1–9

AAC adapter, spare part

numbers 3–27, 3–30, 3–38analog TV tuner, spare part

number 3–27, 3–35Antenna Adapter - DVB-T,

spare part numbers 3–28arrow keys 1–13audio board

removal 5–48spare part numbers 3–8,

3–37, 3–38, 5–48audio board cable, removal

5–60audio troubleshooting 2–31audio-in (microphone) jack

location 1–7pin assignments D–6

audio-out (headphone) jacklocation 1–7pin assignments D–6

Bbackpack, spare part number

3–27, 3–31Backup and Recovery

Windows Vista C–1Windows XP B–1

backup suggestions B–2, C–2

base enclosure, spare part numbers 3–10, 3–37, 3–38, 3–40

batteryremoval 5–5spare part numbers 3–8,

3–38, 5–5specifications 6–7

battery bay 1–20battery light 1–6battery release latch 1–20Bluetooth module

removal 5–50spare part number 3–8,

3–35, 5–50bottom components 1–20

CCable Kit, spare part number

3–20, 3–40cables, service considerations

4–2caps lock key 1–13carrying case, spare part

number 3–28, 3–35CMOS clearing 1–4components

bottom 1–20front 1–6keyboard 1–12left-side 1–8rear 1–8

Maintenance and Service Guide Index–1

Index

right-side 1–10top 1–14, 1–16, 1–18

composite S-Video and audio input cable, spare part number 3–27, 3–35

computer feet, locations 5–10Computer Setup

Advanced Menu 2–7, 2–14File Menu 2–5, 2–12Security Menu 2–6, 2–12Tools Menu 2–6, 2–12

computer specifications 6–1connector pin assignments

external monitor D–4headphone D–6microphone D–6monitor D–4RJ-11 (modem) D–5RJ-45 (network) D–2S-Video-out D–3Universal Serial Bus (USB)

D–1connectors, service

considerations 4–2consumer infrared lens 1–7creating

recovery discsWindows Vista C–4Windows XP B–4

system restore pointWindows Vista C–3Windows XP B–3

Ddeleting

recovery partitionWindows Vista C–8Windows XP B–9

design overview 1–22disassembly sequence chart

5–3diskette drive, OS loading

problems 2–29display assembly



display bezelremoval 5–34, 5–36spare part numbers 3–21,

3–39, 5–36Display Cable Kit, spare part

number 3–22, 3–39display enclosure, spare part

numbers 3–22, 3–36, 3–38display hinge


5–39Display Hinge Kit, spare part

number 3–22, 3–39, 5–39display panel


3–36, 5–38Display Screw Kit, spare part

number 3–22, 3–36docking device,

troubleshooting 2–24


Index

drive light 1–7drives, preventing damage 4–3DVB-T TV Tuner, spare part

numbers 3–35DVBTV tuner, spare part

number 3–27DVD/CD-RW Combo Drive

OS loading problems 2–30precautions 4–3removal 5–20spare part number 3–10,

3–24, 3–37, 5–20specifications 6–8

DVD±RW/R and CD-RW Combo Drive

OS loading problems 2–30precautions 4–3removal 5–20spare part numbers 3–10,

3–24, 3–37, 5–20specifications 6–10

Eelectrostatic discharge 4–4,

4–8expansion port 3 1–8ExpressCard assembly


3–37, 5–52ExpressCard slot 1–11ExpressCard slot bezel

illustrated 3–25removal 5–53

external monitor portlocation 1–8pin assignments D–4

Ffan/heat sink assembly


3–38, 3–39, 5–61features 1–2feet, locations 5–10flowcharts, troubleshooting

no audio 2–31, 2–32no network/modem

connection 2–36no OS loading 2–25no OS loading from

diskette drive 2–29no OS loading from hard

drive 2–26, 2–27, 2–28no OS loading from optical

drive 2–30no power 2–18, 2–20, 2–21no video 2–22, 2–23nonfunctioning device

2–33nonfunctioning docking

device 2–24nonfunctioning keyboard

2–34nonfunctioning pointing

device 2–35fn key 1–13front components 1–6function keys 1–13

Ggrounding equipment and

methods 4–7


Index

Hhard drive

OS loading problems 2–26precautions 4–3removal 5–6spare part numbers 3–10,

3–24, 3–36, 3–37, 3–39, 3–40, 3–41, 5–6

specifications 6–4hard drive bay 1–21Hard Drive Bracket Kit, spare

part number 3–24, 3–40, 5–6hard drive bracket, removal

5–9hard drive cover

illustrated 3–25removal 5–7

HDMI port 1–9headphone jack


headset, spare part number 3–27, 3–30

hingeremoval 5–39spare part number 3–22,

3–39, 5–39

II/O address specifications

6–15infrared receiver

spare part numbers 3–40infrared receiver, spare part

numbers 3–27interrupt specifications 6–13

inverterremoval 5–37spare part number 3–21,

3–36, 5–37

Kkeyboard


3–5, 3–41, 5–25troubleshooting 2–34

keyboard components 1–12keypad keys 1–13

Lleft-side components 1–8Logo Kit, spare part number

3–27, 3–37

Mmass storage devices, spare

part numbers 3–23media button 1–17memory module


3–36, 3–39, 5–11memory module compartment

1–21memory module compartment

coverillustrated 3–25removal 5–12

Memory Reader 1–9microphone

location 1–15removal 5–41spare part number 3–22,

3–36, 5–41


Index

microphone jacklocation 1–7pin assignments D–6

Mini Card moduleremoval 5–15spare part numbers 3–12,

3–14, 3–16, 3–18, 3–20, 3–31, 3–32, 3–33, 3–34, 3–35, 5–15

modem jacklocation 1–9pin assignments D–5

modem, troubleshooting 2–36monitor port


mouse, spare part number 3–27, 3–28, 3–40

Nnetwork jack


network, troubleshooting 2–36nonfunctioning device,

troubleshooting 2–24, 2–33num lock board, removal 5–24num lock key 1–13

Ooptical drive

location 1–11, 1–20OS loading problems 2–30precautions 4–3removal 5–20spare part numbers 3–10,


optical drive bracket, removal 5–21

Ppacking precautions 4–5password clearing 1–4performing a recovery


plastic parts 4–2Plastics Kit

contents 3–26spare part number 3–6,

3–26, 3–40pointing device,

troubleshooting 2–35power button 1–15power button board


3–37, 5–29power connector 1–11power cord

set requirements E–2spare part numbers 3–28,

3–30power light 1–6power management features

1–5power, troubleshooting 2–18processor


3–35, 3–36, 3–39, 3–40, 3–41, 3–42, 5–64


Index

Rrear components 1–8recovering from partition on

hard driveWindows Vista C–7Windows XP B–8

recovering from the recovery discs


remote controlspare part numbers 3–40,

3–41remote control, spare part

numbers 3–27, 3–33, 3–40removal

preliminaries 4–1procedures 5–1

replacementpreliminaries 4–1procedures 5–1

RF cable, spare part number 3–27, 3–35

RF input adapter cable, spare part number 3–27, 3–35

right-side components 1–10RJ-11 (modem) jack


RJ-45 (network) jacklocation 1–9pin assignments D–2

RTC batteryremoval 5–14spare part number 3–20,

3–37, 5–14

Rubber Feet Kit, spare part number 3–37

SScrew Kit, spare part numbers

3–29, 3–37, 3–40screw listing A–1security cable slot 1–11serial number 3–1, 5–2service considerations 4–2Setup Utility 2–1speakers 1–15specifications

battery 6–7computer 6–1display 6–3DVD/CD-RW Combo

Drive 6–8DVD±RW/R and CD-RW

Combo Drive 6–10hard drive 6–4I/O addresses 6–15interrupts 6–13optical drive 6–8system DMA 6–12

static shielding materials 4–8S-Video-out jack


switch coverremoval 5–22spare part numbers 3–3,

3–37, 5–22system board

removal 5–57


Index

spare part numbers 3–8, 3–35, 3–39, 3–41, 3–42, 5–57

system DMA 6–12

Ttools required 4–1top components 1–14, 1–16,

1–18top cover


3–40, 5–42TouchPad 1–19TouchPad buttons 1–19TouchPad horizontal scroll

zone 1–19TouchPad light 1–19TouchPad on/off button 1–19TouchPad vertical scroll zone

1–19transporting precautions 4–5troubleshooting

audio 2–31docking device 2–24flowcharts 2–15keyboard 2–34modem 2–36network 2–36nonfunctioning device

2–24, 2–33OS loading 2–25overview 2–1pointing device 2–35power 2–18video 2–22

TV tunerspare part numbers 3–40

TV tuner antennaspare part numbers 3–40

TV tuner remote control, spare part number 3–27, 3–35

TV tuner, spare part numbers 3–27

UUniversal Serial Bus (USB)

portlocation 1–9, 1–11pin assignments D–1

unknown password 1–4USB digital drive, spare part

number 3–24, 3–30USB infrared receiver, spare

part number 3–27, 3–35USB/power connector board


3–38, 5–55USB/power connector board

cable, removal 5–60using system restore points

B–3, C–3

Vvents 1–21video troubleshooting 2–22volume mute button 1–17volume scroll zone 1–17

WWindows applications key

1–13Windows logo key 1–13


Index

wireless antennaremoval 5–40spare part number 3–22,

3–36, 5–40wireless laser mouse, spare

part numbers 3–27, 3–35wireless light 1–7wireless switch 1–7workstation precautions 4–6


Index


Index


Index
