Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Made to Measure Window Furnishings
Innovative Solutions to Add Value for your Customer
Sales Product Training Module 10.8.1 MotorMax for Motorised Internal Blinds
Revision G 7th November 2013
jpm-speed.com
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– Motormax Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMax Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Roller Blinds Overview Operation & Advantages
– MotorMax motor FITS 45mm Min. dia. tube & will LIFT 8m2 of blinds
– Fast & easy to program with stepping adjustment for easier leveling
– A cord-free solution where child safety is paramount
– Quiet operation, emitting less noise than almost all other similar motors
– Motorisation increases
• Lifting mechanism life as it is not exposed to daily incorrect use
• Fabric life as it is not exposed to daily incorrect handling
• Energy efficiency if Home Automation used to program automatic closing of
blinds during hot sunny times of day
• Home Security if Home Automation used to randomly program opening &
closing of blinds when customer is away on holidays
– The MotorMax motor can be wired for either of the following 2 operating systems;
1. R.T.S. Remote - Radio Transmitted Signal = RTS Remote
2. Home Automation - Microprocessor Computer Controlled
- THIS MOTOR CANNOT BE WIRED DIRECTLY ACROSS A 240 VOLT WALL SWITCH
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motors are a Cost Effective & Add Value to a Solution
A Motorised Blind provides ease of operation, increased security, energy
efficiency & comfort to a home.
10% of industry blind sales are typically motorised & this segment of the
market is growing.
Motorised blinds offer a superior solution by removing unsightly chains for
blinds over wide sliding doors and are a child safe solution.
Add value to your offer & differentiation with motorised blinds.
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Internal Blinds Motorisation MotorMax Motor Technical Specifications
o Australian Designed & Patented Motor – CE Approved
- 5 year warranty on motor parts & 2 year warranty on remote transmitter
o Electrical Specifications
- 240 Volt x 0.6 Amps x 50 Hz
- Total Power = 144Watts
- 4 minutes maximum running time with thermal cut off
o Motor Dimensions
- Motor is 35mm Outside Diameter x 585mm long – to suit a 45mm tube
- Motor head thickness is 11mm
- Motor weight is 1.5Kgs
o Blind Lifting Capacity
- Approximately 28kilograms of lifting power will lift up to 8 sq. metres of linked blinds
- Output speed = 28 RPM
- Maximum Torque = 6Nm
o Motor Modes of Operation
- 433.92 MHz Radio Controlled
- 5 volt Home Automation hardwired dry contact switch input
- Simultaneous Radio and Home Automation - without extra hardware interface boxes
- Electronic Limits set by remote
Remote Transmitter - 1 or up to11 Channel Remote with an indoors transmitting range up to 30metres
- Battery life is approximately 2 years if the handset is only used a few times per day.
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMax Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motor Operating Systems Remote Control Operation by Radio Transmitted Signal (R.T.S.)
The MULTI CHANNEL Remote Control Handset features 5 control buttons; UP, DOWN,
LEFT, RIGHT & STOP.
The Up & DOWN buttons control the blind’s vertical movement .
The LEFT & RIGHT buttons are for channel selection or settings.
The RIGHT button is for channel selection of channels 1 to 6, & the LEFT button is for
channels 7 to 11.
One handset is capable of numerous operations. It can;
Operate up to 11 motors individually; one on each channel
Operate up to 10 motors individually on channels 1 to 10. Channel 11 can be
programmed to operate all 10 motors as a group together.
Operate up to 11 GROUPS of motors; each group is operated independently of each
other. Each group can contain any number of motors & all motors within the group
operate simultaneously.
Each motor can be programmed onto 24 different channels. The last transmitted
channel will be retained by the handset for the next transmission. Remote Transmitter with Wall Holder
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motor Operating Systems Home Automation Operation
A Home Automation Systems(HAS) is a microprocessor controlled operating system that is programmed to allow you to
operate various electrical appliances in your home from one master controller.
e.g. Burglar alarms, lighting, entertainment, garden watering & air conditioning systems, blinds, curtains & awnings
The use of an iPhone, iPad or other portable device as a master controller is becoming popular so the HAS can be
operated away from the home when people are away.
In addition to 240 volt power cables, separate special 5 volt, low voltage, twisted pair cabling is required, and in most
cases the HAS wiring is installed at the time a new house is built.
MotorMax motors have a separate HAS cable port & optional data cable
Well known manufacturers of HAS are;
C-Bus
Dynalite
Crestron
X10 & A 10 (Wireless system - tends to be D.I.Y. & not compatible with MotorMax)
240V
Cable
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
• Home Automation is usually installed by two (2) separate companies
– An electrician to run & connect the wires
– A 3rd party programmer to write the software, test & commission (CHECK)
• The customer needs to be made aware that they are responsible for checking
the wires are connected correctly, interlocking relays are installed (to
prevent the blind motor being accidentally programmed to operate up & down
at the same time) & software is correct – any damaged to blinds or motors as a
result of Home Automation malfunctions will Void Warranty.
• On installation our installer will test the operation of each blind & check the top
& bottom limits are set correctly using a test lead connected into the Molex
connector & an RTS transmitter
• Strongly recommend a letter be sent to the customer advising of precautions to
be taken using Home Automation & special Warranty conditions.
• In most cases it is simpler to keep the motorised blinds separate to the Home
Automation system & just use a Multi Channel Transmitter with Group Control
programming functions.
Motor Operating Systems Home Automation Operation – Key Installation Issues
Recommend to use dry contact
relay modules if working with
other Home Automation Systems
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Important Information Electrical safety
ELECTRICAL SAFETY
• It is important for the safety of persons to follow these instructions, as incorrect installation can lead to severe injury. Keep these
instructions for future reference.
• Electrical work must be installed by a licensed electrician in compliance with current safety regulations and these instructions
• Before installing the system, remove any unnecessary cords and disable any equipment not needed for powered operation.
• The motor must not be subject to crushing, impact, dropping or contact with any kind of liquid. Do not puncture or penetrate any part
of the motor housing.
• The motor has been designed for the automation of Roman & roller blinds in residential and commercial environments; any other
use is considered improper and is not recommended.
• The supply cable attached to the system can not be replaced. If the cable is damaged, the appliance must be returned to after sales
department in order to avoid danger.
• Before carrying out any form of maintenance, switch off the power to the motor.
• Use only approved accessories, such as power leads, brackets and transmitters.
• Examine the installation at regular intervals. Do not use the installation until any faults have been rectified and adjustments made.
• Do not allow children to play with any controls. Keep remote controls away
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Important Information Electrical Isolation Switches
ELECTRICAL ISOLATION SWITCHES
• Isolation switches allow you to isolate the power
to each motor
• Isolation switches are highly recommended to
have installed
• Speak to your electrician regarding the isolation
switches prior to wiring.
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Important Information Draft Letter for Customers Using Home Automation
Dear xxxxxxx
RE: Connection of Motors to the Home Automation System
Thank you for choosing Our Company to supply Motorized Blinds or your new home
The specification for the Blinds at the above address is that they be connected to the Home Automation System. The purpose of this letter is to outline the requirements for connecting any
motors used in the Blinds to the Home Automation System.
Whilst it is physically possible to wire motors directly into Home Automation System this should not be done. We recommend that motor manufacturer’s controllers designed specifically to allow
control of Motors by a Home Automation System be installed.
These controls ensure that the motor is correctly switched and give the following functionalities:
No possibility of an Up and a Down power feed at the same time. An Up and a Down power feed simultaneously will lead to failure of the motor.
Correct Operation of the Limit Switch of the Motor. This ensures the motor only runs to preset positions. Failure of a limit can lead to damage to the Blind/Awning.
Time out function. After three minutes the power supply to the motor is automatically cut. This increases the lifespan of the motor whilst still allowing enough time for the blind/awning to run
through its full drop/extension.
Parallel Wiring: Under no circumstances must motors be wired in parallel i.e., more than one motor connected to a relay.
Should the building specification require that motors be switched off one relay in a group operation then a motor manufacturers “Motor Group Controller” must be used.
Motors wired in parallel will lead to failure of the motor and possible damage to the Blind/Awning and is not covered under warranty.
To ensure many years of trouble free operation of your motors Our Company requests that your Home Automation System Electrician / Integrator use proprietary controllers in your new home
Our Company would also like to take this opportunity to request that you acknowledge receipt of this letter and attached technical information supplied to Our Company by the motor
manufacturer and that this technical information will be forwarded to the Home Automation System Integrator and Electrician.
Should the Home Automation System Integrator and Electrician choose not to use the recommended motor manufacturer’s controllers Our Company takes no responsibility for the operation of,
or any subsequent failure or damage to either, the motors or the Blinds that are controlled through the Home Automation System.
Should you require any further information on any of the above please do not hesitate to contact us.
Best Regards,
Xxxxxx xxxxxx
I acknowledge that I have received this letter and attached technical information and fully understand and accept the information contained herein.
……………………………………… …………………………..
CUSTOMER NAME DATE
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMax Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Product Information Component Information
Roller Blinds
45mm Motor Tube Adaptors (Crown & Wheel)
Dependant Linked Blinds
Double Linked Bracket Blinds
Roman Blinds
Molex Connectors – RTS
Transmitters – 1 channel & 11 channel
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
45mm Dia. Tube
Product Information 45mm Diameter Tube Adaptors - Crown & Wheel
Wheel Bracket & Adaptor Plate 45mm Dia. Tube Crown
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Control System Options Dependent Linked Blinds
• Control system where up to 3 Blinds are linked together &
operated together by 1 motor
• Maximum blind area that may be linked together is 8 sq. metres.
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Control System Options Double Brackets - 2 Blinds installed on one set of brackets
• Control system where 2 Blinds , using 45mm diameter
tube, are installed on one set of 38mm tube brackets
1. Viewscreen blind for the daytime
2. Block out blind for night time privacy – fit closest to
the window for smaller light gaps
• Suited for installation in deeper reveals
• For shallow reveals consider single brackets.
– Reveal fit block out blind
– Face fit sunscreen blind
• 45mm tube adaptors available to fit 38mm brackets.
• Double linked blinds may also be motorized, using
45mm diameter tube
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Control Systems Options Motorised Roman Blinds
• Motorisation System is practically the same
concept as a motorised Roller Blind.
• A motor is fitted inside a 45mm dia. tube
system & attached to a 70mm headboard
using 45mm Roller Blind brackets.
• The blind is lifted from the cord that winds
itself around the 45mm system as it is raised
and lowered; just like fabric would on a Roller
Blind.
• Motor is supplied fitted with a Molex
connector. A separate Molex “Tail” is
supplied to the client for their electrician to
install ready for the blind
• Maximum motorised blind area is 6sq.mtrs
Retrousse & Façade Roman blinds may be motorised
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motorised R.T.S. Roller Blind Electrical Installation – Molex Connector
• Motorised roller blinds are supplied fitted with a
motor cable.
• End of motor cable is supplied fitted with a
“Molex” plug.
• “Molex” plugs are suitable for internal use only.
• A separate loose “construction cable” fitted with a
“Molex” plug is supplied. After installation of the roller
blind this can be connected to the motor plug
• This loose “construction cable” is supplied separate to
the blinds & MUST ONLY BE CONNECTED to the
HOUSE ELECTRICAL SYSTEM by a LICENSED
ELECTRICIAN
• Electrician should NOT coil up loose motor cable as the
earth wire also acts as an RTS antenna
Molex Connector
Construction Cable
& Motor Cable after
connection
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motorised Roller Blinds Recommended Molex Cable Safety Cover
• Molex cover be fitted as part of the installation
• All cables as supplied with safety label which must not be
removed
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Control System Options MotorMax RTS Transmitters
Single Channel Transmitter Multi (11) Channel Transmitter
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMax Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motorisation Installation Guidelines – 240Volt Wiring
It is important for the safety of persons to follow these instructions, as incorrect
installation can lead to severe injury.
Before installing the system , remove any unnecessary cords & disable any
equipment not needed for powered operation
Electrical work must be installed by a licensed electrician in compliance with
current safety regulations & these instructions
The motor must not be subject to crushing, impact, dropping or contact with any
kind of liquid. Do not puncture or penetrate any part of the motor housing
The motor has been designed for the automation of roller blinds & Roman blinds in residential & commercial environment: any
other use is considered improper & not recommended
The supply cable attached to the motor cannot be replaced. If the cable is damaged, the appliance must be replaced
Loading weight & operating time must be compatible with the system specifications
Before carrying out any form of maintenance, switch off the power to the motor
Only use approved accessories, such as power leads, brackets & transmitters
Examine the installation at regular intervals. Do not use the installation until any faults have been rectified & adjustments made
Do not allow children to play with any remote controls. Keep remote controls away from children.
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motorisation Installation Guidelines – Home Automation Wiring
Separate C-Bus Wiring & Connection
240V Cable Motor Head Cable Port
Control Cable Connector
Motor Head
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motorisation
Installation Guidelines - Motorised Blinds Cable Entry
80mm
150mm long motor lead with Molex connector
•Drill 30mm Min. dia. To positioned Molex
connection & cover above ceiling off set to
the window corner of the architrave to cable
is well clear of the blind fabric
Molex Connector Tail & Safety Cover
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Child Safety - Corded Internal Window Coverings
Trade Practices Regulations 2010
Important for Safe Installation & Operation
In the sales process inform each customer of December 2010
ACCC National Safety Standards & our requirement to fit safety
labels and for our installer to fit safety cleats.
– We PROVIDE a warning label on the chain or cord to highlight
the risk of strangulation to children.
– Sales consultant should recommend to keep cots and furniture
away from window coverings, cords/chains, to install & use
safety devices that remove the cord loop or reduce access to
cords
– Motorised blinds are child safe as there are no chains.
– It is not necessary to drill holes to screw safety cleats
onto the window frame or wall.
X a
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMax Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Motorisation MotorMax Programming Overview
Easy programming methodology with the option to reassign channels without the need to reset limits
Full electronic limit setting. Can reset limits without the need to access the motor
Individual or group motor control with up to 11 channels remote
Group and channel control can be deleted and modified without deleting limit settings.
Micro-Stepping adjustment of approx 1-2mm increments ensures quick and easy levelling for perfect
alignment of bottom bars at the top and bottom positions
CBus / hard wired ready. Can be used simultaneously with Radio Remote control & CBus without
added hardware interface boxes.
The factory will set the limit 5 - 10mm shorter than the drop so blind stops before hitting sill or floor.
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Single Remote Programming Example
1. If you use a Single Remote all 4 blinds will
operate at the same time.
Multi Remote Programming Example
1. If you use a Multi Remote you are able to set UP TO
11 motorised blinds to operate individually, using
separate channels.
2. Using a separate (unused) channel to Group all 4
blinds to operate at the same time.
Blind A Blind B
Blin
d D
Blin
d C
(Ch 5)
Group Control
(Ch 4) (Ch 3)
(Ch 2) (Ch 1) Blind A Blind B
Blin
d D
Blin
d C
One Channel
Receiver
Group Control
Motorisation MotorMax Programming Options
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Programming Options Multi Channel Remote to Individually Control 3 Windows
INDIVIDUAL CONTROL
Channel 1 – left hand window
Channel 2 – centre window
Channel 3 – right hand window
GROUP CONTROL
Channel 4 – All 3 widows together
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
MotorMax Programming Options Enabling & Disabling of Channels
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
MotorMax Programming Options Allocating (“Pairing”) a Remote Channel to a Motor
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
MotorMax Programming Options Changing Motor Rotation Direction
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Programming - Setting Limits for First Installation
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
MotorMax Programming Options Adjusting Individual Limit Positions
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
MotorMax Programming Options Restoring Factory Modes
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
MotorMax Programming Options one2one Programming Key
!
- Second, the remote can be entered into a special UNIVERSAL PROGRAMMING CHANNEL (UPC), which enables a unique
programming channel available with single channel remote controls.
Once you enter the special "one2one" UPC as below, you can perform all the normal programming functions on the motor.
Once motors in the room will not respond to the programming commands as they cannot hear the UPC without the one2one
key being inserted. When you exit the "one2one" mode, all motors that are linked to your remote control will be back in
normal operating mode.During one2one operation, please check that you are staying on the "one2one" programming channel which is indicated by
the fact that BOTH channel indicators 2+5 are lit. If you accidentally move away from this channel, use LEFT or RIGHT buttons to
NOTE: one2one keys are available on request
USING THE "one2one" PROGRAMMING KEY
The patent pending "one2one" system, is a unique time saving technology, which allows installers and programmers or re-
program individual RF controlled motors without the need to power-down the motor being programmed, or any other motors
in the building. It uses a specially designed access key, available to installers and programmers, which provides two seperate
- First, insertion of the key, simulates turning the power to the motor OFF then ON again. This allows access to all the normal
functions available after power up of the motor as explained on Pages 1 & 2 above.
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Programming Options - one2one Programming
o2o-1
Insert the "one2one" progrmming key into the dry contact digital switching connector on the
motor. Be careful not to force the key, which may damage the contacts inside the connector.
Note: appearance of key may vary from picture shown on the right. The motor should emit one
long beep.
NO
TE
o2o-2BRIEFLY press button inside the small round hole on the back of the hand held remote control.
Use a paper clip or similar.
020-3Simultaneously press UP and DOWN - you will see both the channel 2 and channel 5 indicator
lights come on simultaaneously on the screen of the remote control.
o2o-4 Press STOP while channel indicators are still glowing red.
o2o-5Simultaneously press UP and DOWN again - the motor will "jog" to confirm it is in "one2one"
programming mode.
!
See programming
steps as referred
See programming
steps as referred
See programming
steps as referred
See programming
steps as referred
TO EXIT "ONE2ONE' MODE: REMOVE THE KEY - WAIT 45 SECONDS - MOTOR IS BACK IN NORMAL MODE. On the REMOTE:
ensure you are on the 2 + 5 channels (use LEFT or RIGHT button until both lamps light up), then push hidden button on back,
then press UP + DOWN simultaneously, and finally press STOP to de-activate the "one2one" mode on the remote.
DELETING CHANNELS: You can now execute steps DC2 - DC3 (but without step DC1)
DELETING LIMIT SETTING: You can now execute steps DL2 - DL3 (but without steps DL1)
DELETING CHANNELS and LIMITS: You can now execute steps DCL2 - DCL3 (but without step DCL1)
REVERSING MOTOR DIRECTION: You can now exectute steps CD1 - CD2 (CAUTION: REVERSING DIRECTION
ALSO DELETES LIMITS!)
AT THIS POINT THE REMOTE IS NOW COMMUNICATING EXCLUSIVELY WITH THE MOTOR WITH THE KEY INSERTED. ALL NORMAL
PROGRAMMING FUNCTIONS CAN BE PERFORMED, BUT WITHOUT HAVING TO REMOVE POWER TO THIS OR ANY OTHER
MOTOR.
See programming
steps as referred
See programming
steps as referred
ENTERING "ONE2ONE" PROGRAMMING MODE
Once you enter the special "one2one" UPC as below, you can perform all the normal programming functions on the motor.
Other motors in the room will not respond to the programming commands as they canot hear the UPCwithout the one2one
key being inserted.When you exit the "one2one" mode, all motors that are linked to your remote control will be back in
normal operating mode.
See programming
steps as referred
ADDING CHANNELS OR REMOTES: You can now execute programming steps A2 - A5 (but without step A1)
SETTING LIMITS: You can now execute programming steps L2 - L15 (but without step L1
ADJUSTING INDIVIDDUAL LIMITS - ENSURE BLIND IS IN POSITION TO BE ADJUSTED FIRST: You can now
execute any of the steps L4 to L7, L8 to L11 or L12 to L15 as required.
SIMULTANEOUS
Press Briefly
SIMULTANEOUS
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMAX Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Common Problems, Causes & Solutions
Problem Possible Cause Possible Solution
Motor operating properly when installer
tested using test lead but not working
after electrician wired cables into house
When electrician turns power off to
wire & then turns power back on after
wiring the motor is in program mode for
30 seconds & pressing buttons during
this time will change the program
For single channel remote press UP &
DOWN pushbuttons simultaneously to
pair remote with motor. Motor will jog &
emit a beeps to confirm pairing
Remote not working properly after
electrical installation
Motor cable acts as antenna & will not
function properly if loose cable is
bunched or coiled up
Check loose cable is not bunched up. If
so uncoil & layout the cable in a loop
2 motors installed with both motors in
middle (head to head ) do not operate
using RTS transmitter
Electrical magnetic fields interfering
with radio waves
Install motors on opposite end of roller
blinds so they are as far away from
each other as possible
One of two (2) blinds 1,900mm wide x
2,200mm drop installed with 1 motor
does not work
Total blind area is 8.36sq. metres
exceeds maximum lift specification
area of 8 sq. metres & connecting link
may be snapped
Install separate motors for each blind
Motors wired up to a CBus system are
not working.
Possible programming malfunction,
may have resulted in UP & DOWN
electrical signals at the same time,
resulting in the motor being burnt out.
Customer CBus electrical contractor
should install interlocking relays.
Motor damage not covered by warranty
& new motors will be required
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMax Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Roller Blinds Review of This Modules Key Issues
Innovative Solutions to Add Value for your Customer
• High Quality MotorMax motor with a 5 year manufacturers parts warranty
• 10% + of the blind market is motorized & growing at +10% per year.
• MotorMax motor is very competitively priced to help us add value & grow our share of this market
• Unique motor that may be wired for – R.T.S. & Home Automation Systems (with separate data cable)
• Wide range of 45mm diameter tube operating systems that can be motorized
– Roller Blinds
• Dependant Linked systems – child safe solution as loose chains eliminated over sliding doors
• Dual brackets
– Roman Blinds
• Installation Guidelines - where to drill holes for cable & wiring guidelines
• Programming options – easy to program & has unique one2one programming feature
• Child safe solution – not necessary to drill holes to screw safety cleats onto the window frame or wall.
• Common problems
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Sales Product Training Contents for Module 10.8.1 – MotorMax Motorised Blinds
1. Overview
– MotorMAX Operation & Advantages
– Technical Specifications
2. Motor Operating Systems Options
– RTS Remote
– Home Automation
– Important Information
3. Product Information
4. Installation & Child Safety Guidelines
5. Programming
6. Common Problems, Causes & Solutions
7. Summary
8. Knowledge & Learning Assessment Test
Structured Product Education & Evaluation Development - eLearning
jpm-speed.com
Knowledge & Learning Assessment Test Certificate of Achievement