MA1707-EB © 2017 CASIO COMPUTER CO., LTD. Operation Guide …

ContentsBasic Operations

Watch Face Items

Navigating Between Modes

Mode Overview

Using the Crown

Hands and the Day Indicator Movement

Solar Charging

Using Mobile Link with a MobilePhone

Getting Ready

A Installing applicationsB Configuring Bluetooth SettingsC Pairing the watch with a phone

Auto Time Adjustment

Configuring World Time Settings

Configuring Stopwatch Settings

Viewing Stopwatch Data

Setting the Alarm

Adjusting Hand and Day Indicator Alignment

Phone Finder

Configuring Watch Settings

Returning the Watch to Its Factory DefaultSettings

Changing the Home City Summer Time Setting

Checking the Watch Charge Level

ConnectionConnecting with a PhoneDisconnecting from a PhoneUsing the Watch in a Medical Facility orAircraftUnpairingAfter Purchasing Another Phone

MA1707-EB © 2017 CASIO COMPUTER CO., LTD.

Watch SettingsSetting the Time and Date

Configuring Dual Time Settings

Swapping Your Current Location Time andDual Time Settings

StopwatchSplit Times and Lap Times

Measuring Elapsed Time

Taking a Split Time Reading

Checking the Difference between a Lap Timeand the Target Time

Target Value Type

Enabling or Disabling Alert Sounds

Example: Recording a Race Lap Time

AlarmConfiguring Alarm Settings

Turning the Alarm On or Off

Stopping an Alarm

Adjusting Hand and Day IndicatorAlignment

Adjusting Hand and Day Indicator Alignment

International Travel

Other InformationSummer Time Switching

Supported Phone Models

Specifications

Mobile Link Precautions

Copyrights and Registered Copyrights

Troubleshooting

Operation Guide 5512

1

Basic OperationsThis section provides an overview of the watchand its operations.

Note

● The illustrations included in thisoperation guide have been createdto facilitate explanation. Anillustration may differ somewhatfrom the item it represents.

Watch Face Items

30

②

④

⑦⑧

⑨

⑥①

③

⑤

A Lap evaluation areaWhen the watch is in the Stopwatch Mode, themode hand indicates the difference betweenthe lap time being measured and the targettime.

B F / T marksWhen setting a target lap time in theStopwatch Mode for calculating the differencebetween a lap time and the target value, thesecond hand will point to the current target laptime type.“F”: FASTEST (Fastest)“T”: TARGET (Target)C R markThe retrograde dial hand points to “R” whilethe watch is standing by for connection with aphone.

D Charge levelIn the Calendar Mode and Alarm Mode, theretrograde dial hand indicates the currentbattery charge level.

E e markThe retrograde dial hand points to e while thewatch is connected with a phone.F AL markIn the Alarm Mode, the mode hand points to“AL”.

G Alarm setting, stopwatch alert beepersetting

In the Alarm Mode, the second hand indicatesif the alarm is enabled or disabled.“ON”: Alarm enabled“OFF”: Alarm disabledIn the Stopwatch Mode the second handindicates if the stopwatch alert beeper isenabled or disabled.“ON”: Alert enabled“OFF”: Alert disabledH Day of weekThe mode hand points to the current day of theweek.

I A / P marksWhen configuring time settings in your currentlocation (Home City), the second handindicates whether it is an a.m. time or a p.m.time.“A”: AM“P”: PM

Navigating Between ModesYour watch has the modes shown below.

30

A

A

A

C *

Bluetooth connection

Alarm Mode Stopwatch Mode

Calendar Mode

Any button(Approximately 2 seconds)

Use (A) to navigate between modes. Holddown (A) for about two seconds to enter theCalendar Mode. To connect with a phone,hold down (C) for about 2 seconds.* The watch cannot connect with a phonewhile a stopwatch time measurementoperation is in progress.

Mode Overview● Calendar ModeIn this mode, the main hour and minute handsindicate the current time in your currentlocation (Home City), while the dial hour andminute hands show another time (Dual Time).

30

③ ④⑤⑥

②

①

Phone Finder(Hold down about 1.5 seconds.)

Current location time/World Time swapping (Hold down about 3 seconds.)

A Current day of the week in your currentlocation (Home City)

B Charge level

C Current second in your current location(Home City)

D Dual Time hour

E Dual Time minute

F Dual Time 24-hour handThe A-side of the dial indicates an a.m. time,while the P-side indicates a p.m. time.● Stopwatch ModeIn this mode, the main hour and minute handsindicate the current time in your currentlocation (Home City), while the other handsshow elapsed time as measured by thestopwatch.

30

④ ⑤⑥

③

① ②

Split/Reset

Start/Stop

A Lap evaluationl Checking the Difference between a Lap

Time and the Target Time

B Stopwatch seconds

C Stopwatch 1/20 (0.05) second

D Stopwatch hours

E Stopwatch minutes

F Stopwatch 24-hour handThe A-side of the dial indicates hours 0through 12, while the P-side indicates hours12 through 24.


2

● Alarm ModeIn this mode, the main hour and minute handsindicate the current time in your currentlocation (Home City), while the dial hour andminute hands show the alarm time setting.

30

③ ④⑤

① ② Enabling/Disabling the Alarm

A Mode

B Alarm enable/disableThe second hand will point to “ON” while thealarm is turned on, and to “OFF” while it isturned off.

C Alarm minute

D Alarm hour

E Alarm 24-hour handThe A-side of the dial indicates an a.m. time,while the P-side indicates a p.m. time.

Using the CrownThe watch’s crown is a screw-in (screw lock)type. To use the crown, you first need to rotateit towards you (leftwards) to loosen it.

Loosen

Crown

● Pulling Out and Pushing In the CrownTo perform a crown operation, pull it out to thefirst or second click and then rotate it. Do notpull the crown with too much force.First click

Normal timekeeping

Second click

Important!

● To prevent loss of water resistanceand/or damage due to impact, besure to screw the crown in by rotatingit away from you as you push it in.

Screw in

● When pushing the crown back in,take care not to apply too muchforce.

● Fast Forward/Fast ReverseAfter pulling out the crown, rotating it quicklyin succession in either direction will cause thehands to move forward or back at high speed.While the hands are moving forward at highspeed, quickly rotating the crown insuccession again will increase the speed evenfurther.

● Stopping Fast Forward/Fast ReverseRotate the crown in the direction opposite thatof the ongoing operation or press any button.

Note

● If you do not perform any operationfor about two minutes after pullingout the crown, crown operations willautomatically become disabled. Ifthat happens, push the crown backin and then pull it out again.

Hands and the Day IndicatorMovement

30

Mode hand

Day indicator

● Mode Hand and Day IndicatorMovement

Changing the day setting of the watch will alsocause the mode hand to move.

● Day● It can take anywhere from about 15 to 30

seconds for the day indicator to change aftertimekeeping reaches midnight. The modehand moves as the day indicator changes.

● The day indicator will not change while astopwatch time measurement operation isin progress.

Solar ChargingThis watch runs on power supplied from arechargeable (secondary) battery that ischarged by a solar panel. The solar panel isintegrated into the face of the watch, andpower is generated whenever the face isexposed to light.

● Charging the WatchWhen you are not wearing the watch, put it ina location where it is exposed to bright light.

While you are wearing the watch, make surethat its face (solar panel) is not blocked fromthe light by the sleeve of your clothing. Powergeneration efficiency is reduced even whenthe face of the watch is blocked only partially.

NOYES

Important!

● Depending on light intensity andlocal conditions, the watch maybecome hot to the touch whenexposed to light for charging. Takecare to avoid burn injury aftercharging. Also, avoid charging thewatch under high-temperatureconditions like the ones describedbelow.ー On the dashboard of a vehicle

parked in the sunー Near an incandescent light bulb or

other source of heatー Under direct sunlight or in other

hot areas for long periods


3

● Checking the Charge LevelYou can determine the watch’s current chargelevel by checking the position of theretrograde dial hand.

③

②

④

①

Charge LevelA: Good (High)Charge LevelB: Good (Medium)Charge LevelC: Good (Medium)Charge LevelD: Low

● Remaining Charge and Dead BatteryYou can determine if the charge level is low bychecking the hand movement. Functionsbecome disabled as battery power goes low.

Important!

● Should battery go low or go dead,expose the face (solar panel) to lightas soon as possible.

Note

● Exposing the watch face to light afterthe battery goes dead will cause thesecond hand to revolvecounterclockwise until it stops atsecond 57. This indicates charginghas started.

Low Battery PowerThe second hand jumps at two-secondintervals.

30

Second hand

Dead BatteryAll hands and the day indicator are stopped.

1

● Charging Time GuidelinesThe table below shows guidelines forapproximate charging times.Required Charging Time for 1-day UseLight Intensity Approximate Charging Time

Highp

Low

A 8 minutesB 30 minutesC 48 minutesD 8 hours

Time Required to Achieve Next ChargeLevel

Light IntensityApproximate Charging TimeCharge Level

1Charge Level

2

Highp

Low

A 2 hours 23 hoursB 6 hours 85 hoursC 8 hours 137 hoursD 93 hours -

Charge Level 1 :Time from dead battery until hand movementstartsCharge Level 2 :Time from hand movement starts until a fullcharge

Light Intensity

A Sunny day, outdoors (50,000 lux)

B Sunny day, near a window (10,000 lux)

C Overcast day, near a window (5,000 lux)

D Indoor fluorescent lighting (500 lux)

Note

● Actual charging time depends on thelocal charging environment.

● Power SavingLeaving the watch in a dark location for aboutone hour between the hours of 10 p.m. and 6a.m. will cause the second hand to stop, andthe watch to enter Level 1 power saving. If thewatch is left in this condition for six or sevendays, all hands will stop at 12 o’clock and thewatch will enter Level 2 power saving.Level 1 :Second hand stops to save power.Level 2 :The following operations are stopped to savepower: all hand movement (excluding the dayindicator), Bluetooth connection, and alarmalerts.Recovering from Power Saving OperationPress any button or place the watch in a well-lit area to recover from power saving.

Using Mobile Link witha Mobile Phone

While there is a Bluetooth connectionbetween the watch and phone, the watch timesetting is adjusted automatically inaccordance with the phone’s time setting. Youcan also change the watch’s time settings.

Note

● This function is available only whileCASIO WATCH+ is running on thephone.

● This section describes watch andphone operations.X : Watch operationY : Phone operation

Getting Ready

A Installing applicationsTo use the watch with a phone, first tap one ofthe links below and install the “CASIO WATCH+” app on the phone.

● iOS (iPhone) Usershttps://itunes.apple.com/us/app/id760165998?ls=1&mt=8

● AndroidTM (GALAXY, etc.) Usershttps://play.google.com/store/apps/details?id=com.casio.watchplus

B Configuring Bluetooth SettingsEnable the phone’s Bluetooth.

Note

● For details about settingprocedures, see your phonedocumentation.


4

https://itunes.apple.com/us/app/id760165998?ls=1&mt=8

https://play.google.com/store/apps/details?id=com.casio.watchplus

C Pairing the watch with a phoneBefore you can use the watch in combinationwith a phone, you first need to pair them.

1. Move the phone to be paired with close to(within one meter of) the watch.

2. Y On the Home Screen, tap the “CASIOWATCH+” icon.

3. Y Perform the operation shown on thescreen of the phone to be paired with.

● If a pairing prompt message appears,perform the operation shown on thephone screen.

● When pairing starts, the retrograde dialhand will point to the “R” mark. Whenpairing is complete, the retrograde dialhand will move to e.

Bluetooth mark

Auto Time AdjustmentThe watch can be set to adjust its time settingautomatically each day in accordance with thephone time.To have the watch perform auto timeadjustment, put it into the Calendar Mode.

● Using Auto AdjustYour watch adjusts its time setting four timesa day according to a preset schedule. Itperforms the adjustment operationautomatically as you go about your daily life,without any operation required by you.

12:30

Important!

● Note that the watch will not performauto time adjustment if it enters theCalendar Mode while any one of theconditions below exists.ー The stopwatch is performing a

time measurement operation.ー Watch battery power is low

(retrograde dial hand pointing to“E”).

ー Watch is in Level 2 power saving.ー While it is too far away from its

paired phoneー When communication is not

possible due to radio interference,etc.

ー While the phone is updating itssystem

Note

● If the watch does not indicate thecorrect time even if is able to connectwith a phone, correct the hand anddate indicator positions.l Adjusting Hand and Day Indicator

Alignment● If there is a World Time City specified

with CASIO WATCH+, its time willalso be synchronized automatically.

● The watch will connect with thephone and perform auto timeadjustment at around 12:30 a.m.,6:30 a.m., 12:30 p.m. and 6:30 p.m.The connection is automaticallyterminated after auto timeadjustment is complete.

● Summer TimeOnce the watch is connected with a phone andits time is adjusted with the phone time, itsHome City time and World Time willautomatically switch between standard timeand summer time as required, even if thewatch is no longer connected with the phone.l Summer Time Switching● Adjusting the time setting manually with a

watch operation will cancel auto standardtime/summer time switching.

● A CASIO WATCH+ screen showsinformation about summer time periods.

● Triggering Immediate Time AdjustmentThe watch will synchronize its time setting tothat of the phone immediately when they areconnected with each other. Whenever youwant to adjust the watch’s time setting basedon your phone's time, perform the procedurebelow to connect with a phone.

1. X Press (C).This causes the retrograde dial hand tomove to “R”. The retrograde dial hand willmove to e when a connection isestablished between the watch andphone, and the time setting of the watchwill synchronize with the phone’s timesetting.● The watch will disconnect from the

phone automatically after timesynchronization is complete.

30

Configuring World TimeSettings

Specifying a World Time City with CASIOWATCH+ causes the city’s time to beindicated by the small hour and minute hands.Watch settings can be configured for autosummer time switching for the World TimeCity.

30

Note

● CASIO WATCH+ World Time letsyou select from amongapproximately 300 cities as theWorld Time City.


5

● Selecting a World Time City

1. Y Tap the “CASIO WATCH+” icon.2. X Hold down the (C) button for about 2

seconds.● This causes the second hand to move

to 12 o’clock. Keep (C) depressed atthis time until the second handcompletes one full rotation.

● The retrograde dial hand will move from“R” to e when a connection isestablished between the watch andphone.

3. Y Perform the operation shown on thephone screen. The World Time setting willbe reflected on the watch.The dial hour and minute hands, and thesmall 24-hour hand indicate the currenttime in the selected city and time zone.● You can determine whether a World

Time is a.m. or p.m. by checking theposition of the small 24-hour hand.

30

World Time hour (24-hour)World Time hour and minute

● Configuring the Summer Time Setting





3. Y Perform the operation shown on thephone screen to configure the summertime setting.

Note

● When “Auto” is selected forstandard/summer time switching,the watch will switch betweenstandard time and summer timeautomatically. Do not need tochange the time setting manually forchanges between summer time andstandard time. Even if you are in anarea that does not observe summertime, you can leave the watch’ssummertime setting as “Auto”.

● Changing the time setting manuallywith a watch operation will cancelauto standard time/summer timeswitching.

● A CASIO WATCH+ screen showsinformation about summer timeperiods.

● Swapping Your World Time and HomeTime





3. Y Perform the operation shown on thephone screen to swap your Home Timewith your World Time.

30 30

After swappingBefore swapping

World Time

World TimeHome Time

Home Time

Note

● Auto time adjustment is notperformed for 24 hours afterswapping of the Home Time andWorld Time.


6

Configuring StopwatchSettings

You can specify a target value for comparisonwith lap times measured in the StopwatchMode. You can also enable or disable an alertthat sounds when your current lap timematches the target value.l Checking the Difference between a Lap

Time and the Target Timel Split Times and Lap Times

● Specifying the Target Value TypeYou can specify one of the target valuesdescribed below, which are used to calculatethe difference between your target and actuallap time measurements.FASTEST (Fastest) :Your fastest lap time during the currentsession is automatically set for this targetvalue. This setting is refreshed each time yourachieve a new fastest lap. Resetting thestopwatch to all zeros will also clear this targetvalue.TARGET (Target) :This is a fixed value that you specify usingCASIO WATCH+.





3. Y Perform the operation shown on thephone screen to specify a target valuetype.

Note

● If you specified TARGET (Target) asthe target value type, you shouldalso specify the target value.l Specifying the TARGET (Target)

Value● Changing the target value type while

a stopwatch measurementoperation is stopped will reset thestopwatch measurement value to allzeros.

● Specifying the TARGET (Target) ValueIf you specified TARGET (Target) as the targetvalue type, perform the procedure below tospecify the target value.● The TARGET (Target) value setting cannot

be less than 15 seconds.





3. Y Perform the operation shown on thephone screen to specify the TARGET(Target) value.

Note

● Changing the TARGET (target)value while a stopwatchmeasurement operation is stoppedwill reset the stopwatchmeasurement value to all zeros.

● Enabling or Disabling Alert SoundsYou can configure a setting so the watchsounds a tone when the lap time reaches thetarget value during measurement.





3. Y Perform the operation shown on thephone screen to enable or disable the alertsound.

Note

● Changing the alert sound settingwhile a stopwatch measurementoperation is stopped will reset thestopwatch measurement value to allzeros.


7

Viewing Stopwatch DataThis section explains how to send lap timesand split times (up to 100 records) stored inwatch memory, and other data to your phonefor viewing with CASIO WATCH+.

● Sending Stopwatch Data to a PhoneUse the procedure below to send data fromthe watch to a phone.





3. Y Perform the operation shown on thephone screen to transfer data measuredby the watch to the phone.After data transfer is complete, a list of themeasurement data will appear on thephone display.● Tapping a stopwatch data item displays

its details.

● Checking a Lap TimeUse CASIO WATCH+ to check the data yousent to the phone.

1. Y Tap the “CASIO WATCH+” icon.2. Y Perform the operation shown on the

phone screen to view the measurementdata you want.

Note

● Tapping “Edit” displays a screen thatyou can use to change the data itemtitle and to delete lap time data.

Setting the Alarm





3. Y Perform the operation shown on thephone screen to configure alarm timesettings.

Adjusting Hand and DayIndicator Alignment

If the hands and/or date indicator are out ofalignment even though auto time adjustmentis being performed, use CASIO WATCH+ toadjust them.





3. Y Perform the operation shown on thephone screen to correct hand alignment.

Phone FinderYou can use phone finder to trigger a tone onthe phone to make it easy to find. The tone isforced to sound even if the phone is in themanner mode.

Important!

● Do not use this function in areaswhere phone call tones arerestricted.

● The tone sounds at a high volume.Do not use this function whenlistening to phone output overearphones.

1. X If the watch is connected with a phone,press any button to terminate theconnection.

30 30

After disconnectionConnected

2. X Hold down the (A) button for about 2seconds.This will cause the watch to enter theCalendar Mode.

3. X Hold down the (D) button for about 1.5seconds until the second hand points to“R”.The retrograde dial hand will move to ewhen a connection is establishedbetween the watch and phone, and thenthe phone will sound a tone.● It will take a few seconds before the

phone tone sounds.

4. X Press any button to stop the tone.● You can press any watch button to stop

the phone tone only during the first 30seconds after it starts to sound.


8

Configuring Watch SettingsYou can use CASIO WATCH+ to specify theamount of time until a Bluetooth connection isautomatically terminated, to enable or disablethe watch operation tone, and to configureother settings.





3. Y Select the setting you want to changeand then perform the operation shown onthe phone screen.

Returning the Watch to ItsFactory Default Settings

Using CASIO WATCH+ to reset the watchreturns to the settings below.● Stopwatch

ー TARGET (Target) value: Offー Target value type: FASTEST (Fastest)ー Lap time data: All deleted

● Alarmー Alarm time: 0:00ー Alarm setting: Off

● Mute setting: Off● Connection time: 3 minutes● Auto adjust: Off

1. X Pull out the crown to the second click.2. X Hold down (C) for about 5 seconds.

This will cause the second hand to moveto 12 o’clock and then to “A” or “P” andreset settings.

30

Minutes

HoursMode hand

3. Push the crown back in.

Changing the Home CitySummer Time Setting


2. X Hold down the (C) button for about 2seconds.

● This causes the second hand to moveto 12 o’clock. Keep (C) depressed atthis time until the second handcompletes one full rotation.


3. Y Perform the operation shown on thephone screen to change the summer timesetting.

Checking the Watch ChargeLevel

Use the procedure below to check the currentcharge level with CASIO WATCH+.





3. Y Use CASIO WATCH+ to check thecharge level.


9

Connection

Connecting with a PhoneThis section explains how to establish aBluetooth connection between a phone that ispaired with the watch.● If the watch is not paired with the phone you

want to connect with, perform the procedureunder “C Pairing the watch with a phone” topair them.

1. Move the phone close to (within one meterof) the watch.

2. X While the second hand is not pointing toe, hold down the (C) button for about 2seconds.



Important!

● The watch cannot connect with aphone while a stopwatch timemeasurement operation is inprogress.

● If you have problems establishing aconnection, it could mean thatCASIO WATCH+ is not running onthe phone. On the phone’s homescreen, tap the “CASIO WATCH+”icon. After the app starts up, holddown the watch’s (C) button forabout 2 seconds.

Note

● The connection will be terminated ifyou do not perform any operation onthe watch or phone for a fixedamount of time.To specify the connection limit time,perform the following operation with:use CASIO WATCH+ to select“Watch settings” n “Connectiontime”, and then specify a setting of 3minutes, 5 minutes, or 10 minutes.

Disconnecting from a PhonePressing any button terminates the Bluetoothconnection and returns the second hand to itsnormal operation.

30 30


Using the Watch in a Medical Facilityor Aircraft

Whenever you are in a hospital, on an aircraft,or in any other location where auto signalreceive or connection with a phone may causeproblems, you can perform the procedurebelow to disable it. To re-enable auto timeadjustment, perform the same operationagain.





3. Y Perform the operation shown on thephone screen to enable or disable autotime adjustment.

Unpairing

1. X If the watch is connected with a phone,press any button to terminate theconnection.

30 30



3. Y Perform the operation shown on thephone screen to unpair.

Note

● If you are unable to re-pair the watchwith a phone after unpairing them,use the procedure below to deletepairing information from the watchand then perform the pairingoperation again.A X Pull out the crown to the secondclick.

30

Crown

B X Hold down (D) for about 5seconds.This causes the second hand toperform one revolution and deletes thepairing information.C X Push the crown back in.


10

After Purchasing Another PhoneYou need to perform the pairing operationwhenever you want to establish a Bluetoothconnection with a phone for the first time.lC Pairing the watch with a phone

Note

● If your previous phone is near thewatch while you are trying to pair witha new phone, the watch will pair withthe previous phone, which makes itimpossible to pair with the newphone. If this happens, use theprocedure below to delete theprevious pairing information from thewatch. Also, unregister the watchfrom the CASIO WATCH+ of thephone you will no longer connectwith.A X Pull out the crown to the secondclick.

30

Crown

B X Hold down the (D) button for about5 seconds.This deletes the pairing information.The second hand will point to “0”.C X Push the crown back in.

Watch SettingsUse the procedure below to configure currentlocation time and Dual Time settingsmanually.Getting readyPerform this procedure in the Calendar Mode.l Navigating Between Modes

30

Calendar Mode

Setting the Time and DateWhile the watch is connected to a phone, it willautomatically adjust its day and time settingsto those of the phone. If the watch is notconnected to a phone, use the procedurebelow to adjust its day and time settings.

1. Pull out the crown to the second click.This causes the second hand to move to“A” of the watch’s current time setting isa.m., or “P” if it is p.m., and enables thehour and minute setting operation.

30

MinutesHours

Crown

2. Rotate the crown to adjust the hour andminute settings.

● The Dual Time setting also changes inaccordance with the current timesetting. Crown operation is disabledwhile the Dual Time hour and minutehands are moving.

3. Press (A).This enables the month and day settingoperation.

4. Press (B) to change the month.

30

8

9

10

3

4

2

57

11 1

6

12

DayMonth

5. Rotate the crown to change the day.6. Press (A).

This enables the year 10’s digit settingoperation.

7. Rotate the crown to change the year 10’sdigit.

80

90 30

40

20

5070

10

60

00Year (10’s digit)

8. Press (A).This enables the year one’s digit settingoperation.

9. Rotate the crown to change the year one’sdigit.

8

9 3

4

2

57

1

6

0

Year (one’s digit)

10. On a time signal at the top of a minute,push the crown back in.

Note

● The day of the week is setautomatically in accordance with theyear, month, and day settings.


11

Configuring Dual TimeSettings

Dual Time lets you keep track of the currenttime in another time zone in addition yourcurrent location time.

30

Dual Time

Dual Time 24-hour

1. Pull out the crown to the first click.This causes the second hand to move to12 o’clock.

2. Rotate the crown to change the Dual Timesetting.

● You can set the Dual Time in 15-minuteincrements.

＋

－Crown

Dual Time 24-hour hand

Dual Time minute hand

Dual Time hour hand


Swapping Your CurrentLocation Time and Dual TimeSettings

You can swap the time in your current locationwith the Dual Time by holding down (B) forabout three seconds.

30 30


Dual Time

Dual Time

Current location time

Current location time

Note

● If you are using the small hour andminute hands for Dual Time, only thetime in your current location will beswapped with Dual Time. Dates arenot swapped.

StopwatchThe stopwatch can measure elapsed time upto 23 hours, 59 minutes, 59.95 seconds.In addition to normal elapsed timemeasurements, the stopwatch also lets youtake lap time readings. You can also specify atarget value and have the watch indicate thedifference between a lap time reading and thetarget value (lap time).l Checking the Difference between a Lap

Time and the Target Time

Note

● If an ongoing elapsed timemeasurement operation continuesfor 24 hours, the measurement willstop and the stopwatch will reset toall zeros automatically.

Getting readyPerform this procedure in the StopwatchMode.l Navigating Between Modes

30

Stopwatch Mode

Split Times and Lap Times● Split timeA split time is the time elapsed from the start,up to any point along the course of an event.You can use the operation shown below totake split time readings.

B

D

D

B Goal

Split 3

Split 2

Split 1

Start

● Lap timeA lap time shows the time elapsed during aspecific lap. As with split times, the watchcontinues performing elapsed timemeasurement internally while a lap time orsplit time reading is indicated. The watchcalculates and indicates the differencebetween a lap time reading and the targetvalue.

B

D

D

B Goal

Lap 3

Lap 2

Lap 1

Start

Note

● Lap times can be viewed with CASIOWATCH+ after measurement iscomplete.l Viewing Stopwatch Data

Measuring Elapsed Time

30

Lap evaluation

24-hourMinutesHours

Seconds

1/20 (0.05) second

1. Use the operations below to measureelapsed time.

● The retrograde dial acts as a secondhand for about 30 seconds after a timemeasurement operation is started.

B

B

B

B Stop

Resume

Stop

Start

2. Press (D) to reset the elapsed time to allzeroes.

3. Press (A) twice to return to the CalendarMode.


12

Taking a Split Time Reading

30

Lap evaluation

24-hourMinutesHours

Seconds

1/20 (0.05) second

1. Use the operations below to measureelapsed time.

● Each press of (D) causes the elapsedtime up to that point (split time) to beindicated for 5 seconds.

● The retrograde dial acts as a secondhand for about 30 seconds after a timemeasurement operation is started orafter a split time is indicated.

B

D

B Stop

Split

Start

2. Press (D) to reset the elapsed time to allzeroes.


Note

● Up to 100 split times can be measureduring a single elapsed timeoperation.

● Starting a new stopwatchmeasurement operation causes allthe split time data of the previousoperation to be deleted. If you wantto keep a copy of the previousoperation’s data, transfer it to aphone before starting a newmeasurement operation.l Viewing Stopwatch Data● Taking a split time reading also takes

a lap time reading. You can viewrecorded lap times with CASIOWATCH+.

Checking the Differencebetween a Lap Time and theTarget Time

You can view the difference between the laptime measured internally by the watch and thetarget value. When you start a split timereading operation, the mode hand to move asdescribed below.l Split Times and Lap Timesl Using CASIO WATCH+ to Change the

Target Value Typel Using Watch Operations to Change the

Target Value Typel Specifying the TARGET (Target) Value● The mode hand points to A before

measurement starts.

①

② ③

A

B D

C

A As the lap time approaches the targetvalue, the mode hand moves towards theright from the A position. When the laptime is 10 seconds before the target value,the mode hand will point to B.

B As the lap time progresses towards thetarget value from the point 10 secondsbefore the target value, the mode hand willmove to the right in one-secondincrements. When the lap time is reachesthe target value, the mode hand will pointto C.If the alert tone is enabled, the tone willsound when the lap time reaches thetarget value.

C If the lap time exceeds the target value, themode hand will move towards the right inone-second increments. If the lap timeexceeds the target value by 10 seconds,it will stop at D.

Note

● During an elapsed timemeasurement, pressing (D) to starta split time measurement causes themode hand to indicate the differencebetween the new lap time value andthe target value (and return to stepA of the above procedure).

● When the target value type isFASTEST (Fastest), the mode handwill not move from the A position untilthe first lap time is measured.

Target Value TypeYou can specify one of the target valuesdescribed below, which are used to calculatethe difference between your target and actuallap time measurements.FASTEST (Fastest) :Your fastest lap time during the currentsession is automatically set for this targetvalue. This setting is refreshed each time yourachieve a new fastest lap. Resetting thestopwatch to all zeros will also clear this targetvalue.TARGET (Target) :This is a fixed value that you specify usingCASIO WATCH+.l Specifying the TARGET (Target) Value

1. Pull out the crown to the first click.This will cause the mode hand to move “T”or “F”.● Pulling out the crown while a

measurement operation is in progressin the stopwatch mode will stop theoperation and reset the stopwatch to allzeros.

30

Crown

Target

Fastest

2. Rotate the crown to switch between targetvalue types.




13

Enabling or Disabling AlertSounds

You can configure a setting so the watchsounds a tone when the lap time reaches thetarget value during measurement.

1. Pull out the crown to the first click.This will cause the mode hand to move “T”or “F”.● Pulling out the crown while a

measurement operation is in progressin the stopwatch mode will stop theoperation and reset the stopwatch to allzeros.

2. Hold down (B) for about two seconds.This will toggle alert tone betweenenabled and disabled.● Pressing (B) in place of step 2 will cause

the second hand to indicate the currentsetting.

30

OFFON



Example: Recording a RaceLap Time

This section explains how to measure laptimes in watch memory while watching a race,and check the difference between a lap timeand target value. It also shows how you canview lap times with CASIO WATCH+ after therace is over.l Split Times and Lap Times

30

Before a raceAt this time, you should specify the targetvalue type. If you specify TARGET (Target) asthe target value type, you should also specifythe TARGET (Target) value.l Using CASIO WATCH+ to Change the

Target Value Typel Using Watch Operations to Change the

Target Value Typel Specifying the TARGET (Target) ValueDuring a raceDuring the race, you measure split times. Laptimes are also measured internally by thewatch.

1. X Hold down (A) for about 2 seconds.This will cause the watch to enter theCalendar Mode.

30

2. X Press (A) once.This will cause the watch to enter theStopwatch Mode.

30

Lap evaluation

24-hourMinutesHours

Seconds

3. X Use the operations below to measureelapsed time.

B

D

D

B Stop

Start

Pressing (D) at the end of each lap willrecord each lap time in watch memory.● Lap times are recorded in units of

1/1000 seconds.● You can also use the mode hand to

determine the difference between thelap time measured internally by thewatch and the target value.l Checking the Difference between a

Lap Time and the Target Time4. X Press (D) to reset the elapsed time to

zero.5. X Press (A) twice to return to the Calendar

Mode.After a raceAfter the race is finished, you can view themeasure lap times with CASIO WATCH+.l Sending Stopwatch Data to a Phonel Checking a Lap Time

AlarmThe watch will beep when the alarm time isreached.● The beeper is muted in the cases described

below.ー When battery power is lowー When watch is at Level 2 power savingl Power Saving

Getting readyPerform this procedure in the Alarm Mode.l Navigating Between Modes

30

Alarm Mode


14

Configuring Alarm Settings

1. Pull out the crown to the first click.This turns on the alarm.

30

Crown

24-hourMinutesHours

Alarm on

2. Rotate the crown to change the alarm timesetting.

3. Push the crown back in.4. Press (A) once to return to the Calendar

Mode.

Turning the Alarm On or OffEach press of (B) toggles the alarm betweenon and off.

30

OFFON

Stopping an AlarmWhile the alarm is sounding, press any buttonto stop it.

Adjusting Hand andDay Indicator

AlignmentStrong magnetism or impact can cause thehands and/or the day indicator to go out ofalignment. If this happens, adjust hand andday indicator alignment.

Adjusting Hand and DayIndicator Alignment

1. Pull out the crown to the first click.2. Hold down (D) for about five seconds.

This causes the second hand to performone full revolution and enablesadjustment of second hand alignment.

30

3. Rotate the crown to align the second handwith 12 o’clock.

4. Press (A).This enables adjustment of hour andminute hand alignment.

30

Minute hand Hour hand

5. Rotate the crown to align the hour andminute hands with 12 o’clock.

6. Press (A).This enables adjustment of the retrogradedial hand alignment.

30

7. Rotate the crown to align the retrogradedial hand with “0”.

8. Press (A).This enables adjustment of small hourhand, small minute hand, and small 24-hour hand alignment.

30

Small Hour Hand (24-hour)

Small minute handSmall hour hand

9. Rotate the crown to align the small hourhand, small minute hand, and small 24-hour hand with 12 o’clock.

10. Press (A).This enables adjustment of mode handalignment.

30

Mode hand

11. Rotate the crown to align the mode handwith 0.

12. Press (A).This enables adjustment of day indicatoralignment.

1

Day indicator

13. Rotate the crown to align “1” in the centerof the day indicator.



15

International TravelUse the procedure below to easily change dayand time settings of the watch to a destinationlocation.

● Before Boarding

1. Configure the World Time (Dual Time) tothe current time at your destination.

30

Destination time

Current time

l Configuring World Time Settingsl Configuring Dual Time Settings

2. Disable auto time adjustment.

30

l Using the Watch in a Medical Facility orAircraft

● After Arriving

1. Swap the origin time zone time with thedestination time zone time.

30 30


Destination time

Destination time

l Swapping Your Current Location Timeand Dual Time Settings

2. Enable auto time adjustment.l Using the Watch in a Medical Facility or

Aircraft

Other InformationThis section provides non-operationalinformation you also need to know. Refer tothis information as required.

Summer Time Switching● Connecting with a Phone to SwitchAfter the watch is connected with a phone,summer time switching of Home City time andWorld Time is performed in accordance withthe CASIO WATCH+ setting (Auto/ON/OFF)as described below.Auto :After the watch is connected with a phone,summer time is displayed for the currentlocation time or World Time when it is withinthe summer time period. Otherwise standardtime is displayed.ON :The watch always displays summer time.OFF :The watch always displays standard time.

● Auto Summer Time SwitchingWhen the watch is connected to a phone, it issent summer time period information for yourHome City. If there is a World Time Cityspecified with CASIO WATCH+, informationfor that city will also be sent. If the CASIOWATCH+ summer time setting is “Auto”, thewatch will automatically keep track of thesummer time period and perform summer timeswitching automatically, even if it is notconnected with the phone.

Supported Phone ModelsFor information about supported phonemodels, visit the CASIO Website.http://world.casio.com/os_mobile/wat/

SpecificationsAccuracy at normal temperature :

±15 seconds a monthTimekeeping :

Hour and minute (move at 10-secondintervals), second, day (2000 to 2099 fullauto calendar), day of the week

Dual Time :Hour, minute, 24-hour hand, swapping withHome City time

Stopwatch :Measuring unit: 1/20 (0.05) secondMeasuring capacity: 23:59’59.95” (24hours)Measurement functions: Elapsed time, splittimes, lap/target time difference

Alarm :Setting Units: Hour, minuteBeeper: 10 seconds

Mobile Link :Auto Time Correction

Time setting adjusted automatically atpreset time.

One-touch Time CorrectionManual connection and time adjustment

Phone finderWatch operation sounds the alert soundof the mobile phone.

World TimeCurrent time for a selection ofapproximately 300 citiesHome Time/World Time swapping

Auto Summer Time SwitchingAutomatic switching between standardtime and summer time.

Stopwatch SettingsTarget time; difference between targettime and fastest time or target time

Stopwatch data transfer1/1000-second Stopwatch:100 lap/split time records (date and time,lap/split time, lap number)

Alarm SettingsHand alignment correctionData Communication Specifications

Bluetooth®

Frequency Band: 2400MHz-2480MHzMaximum Transmission: 0 dBm (1 mW)Communication range: Up to 2 meters(depends on environment)


16

Other :Power saving, low battery alert, battery levelindication (battery indicator)

Power Supply :Solar panel and one rechargeable battery

Approximate Battery Life :Approximately 5 monthsConditions

Auto Time Adjustment: 4 times/dayAlarm: Once (10 seconds)/dayPower Saving: 6 hours/day

Mobile Link Precautions● Legal Precautions● This watch complies with or has received

approval under the radio laws of variouscountries and geographical areas. Usingthis watch in an area where it does notcomply with or has not received approvalunder applicable radio laws may be acriminal offense. For details, visit the CASIOWebsite.http://world.casio.com/ce/BLE/

● Use of this watch inside of aircraft isrestricted under the aviation laws of eachcountry. Be sure to follow the instructions ofairline personnel.

● Precautions when using Mobile Link● When using this watch in combination with

a phone, keep the watch and phone closeto each other. A range of two meters isrecommended as a guideline, but the localenvironment (walls, furniture, etc.), thestructure of a building, and other factors mayrequire a much closer range.

● This watch can be affected by other devices(electrical devices, audio-visual equipment,office equipment, etc.) In particular, it can beaffected by operation of a microwave oven.The watch may not be able to communicatenormally with a phone if a microwave ovenis operating nearby. Conversely, this watchmay cause noise in radio reception and thevideo image of a TV.

● Bluetooth of this watch uses the samefrequency band (2.4 GHz) as wireless LANdevices, and use of such devices in closeproximity of this watch may result in radiointerference, slower communication speedsand noise for the watch and the wirelessLAN device, or even communication failure.

● Stopping Radio Wave Emission by ThisWatch

The watch is emitting radio waves wheneverthe second hand is pointing to e (Bluetoothconnected) or “R” (Bluetooth connectionstandby).Even if the second hand is not pointing at e or“R”, the watch will automatically attempt toconnect with a phone four times a day to adjustits time settings.When in a hospital, on an aircraft, or in anyother area where the use of radio waves is notallowed, use the operations below to stopradio wave generation.● Disabling Auto Time Adjustment

Configure CASIO WATCH+ settings todisable synchronization between the watchand phone.l Using the Watch in a Medical Facility or

Aircraft

Copyrights and RegisteredCopyrights

● The Bluetooth® word mark and logos areregistered trademarks owned by theBluetooth SIG, Inc. and any use of suchmarks by CASIO Computer Co., Ltd. isunder license.

● iPhone and App Store are registeredtrademarks of Apple Inc. in the UnitedStates and other countries.

● iOS is a trademark or registered trademarkof Cisco Systems, Inc.

● GALAXY, GALAXY Note, and GALAXY Sare registered trademarks of SamsungElectronics Co., Ltd.

● Android and Google PlayTM are registeredtrademarks of Google Inc.

● Other company names and product namesused herein are trademarks or registeredtrademarks of their respective companies.

Troubleshooting

I can’t pair the watch with aphone.

Q1 I’ve never been able to establish a(pairing) connection between thewatch and phone.

Are you using a supported phone model?Check if the phone model and itsoperating system are supported by thewatch.For information about supported phonemodels, visit the CASIO Website.http://world.casio.com/os_mobile/wat/

Is CASIO WATCH+ installed on yourphone?

The CASIO WATCH+ needs to beinstalled in order to connect with thewatch.lA Installing applications

Are your phone’s Bluetooth settingsconfigured correctly?

Configure the phone’s Bluetooth settings.For details about setting procedures, seeyour phone documentation.iPhone Users● “Settings”n“Bluetooth”n On● “Settings” n “Privacy” n “Bluetooth

Sharing” n “CASIO WATCH+” n OnAndroid Users● Enable Bluetooth.

Is the stopwatch performing a timemeasurement operation?

The watch cannot pair with a phone whilea stopwatch time measurement operationis in progress. Stop the measurementoperation and then pair with a phone.

Other than the above.Some phones need to have BT Smartdisabled to use CASIO WATCH+. Fordetails about setting procedures, see yourphone documentation.On the Home Screen, tap: “Menu” n“Settings” n “Bluetooth” n “Menu” n “BTSmart settings” n “Disable”.


17

I can’t reconnect the watchand phone.

Q1 The watch will not re-connect with thephone after they are disconnected.

Is CASIO WATCH+ running on yourphone?

The watch cannot re-connect with thephone unless CASIO WATCH+ is runningon the phone. On the phone’s HomeScreen, tap the CASIO WATCH+ icon.Then on the watch, hold down theCONNECT button (C) for about 2seconds.

30

Have you tried turning your phone off andthen back on again?

Turn the phone off and then back on, andthen tap the CASIO WATCH+ icon. Next,on the watch, hold down the CONNECTbutton (C) for about 2 seconds.

30

Is the watch’s battery charged sufficiently?The watch cannot connect with a phonewhile retrograde dial hand is pointing to“E”. Charge the watch and then connectwith the phone.


The watch cannot connect with a phonewhile a stopwatch time measurementoperation is in progress. Exit the watch’sAirplane Mode. Then hold down theCONNECT button (C) for about 2seconds.

30

Q2 I changed the phone’s Bluetoothfrom enabled to disabled, and now Ican’t connect anymore.

On the phone, re-enable Bluetooth, and thengo to the Home Screen and tap the “CASIOWATCH+” icon. Next, on the watch, holddown the CONNECT button (C) for about 2seconds.

30

Q3 I can’t connect after turning off thephone.

Turn on the phone and tap the CASIO WATCH+icon. Then on the watch, hold down theCONNECT button (C) for about 2 seconds.

30

Phone-Watch Connection

Q1 I can’t establish a connectionbetween the phone and watch.

Have you tried turning your phone off andthen back on again?

Turn on the phone and tap the CASIOWATCH+ icon. Then on the watch, holddown the CONNECT button (C) for about 2seconds.

30

Has the watch been re-paired with thephone?

After unpairing the watch and phone, re-pair them again.l Unpairing

If you are unable to establish aconnection...

Delete the pairing information from thewatch, and then re-pair the watch andphone.l See "Unpairing".

Changing to a DifferentPhone Model

Q1 Connecting the current watch toanother phone.

Pair the watch with the phone.lC Pairing the watch with a phone

Phone Finder

Q1 Phone Finder does not work.

Are the phone and watch disconnected?Phone Finder does not work duringBluetooth connection.

Is CASIO WATCH+ running on yourphone?

Phone Finder will not work unless CASIOWATCH+ is running. On the HomeScreen, tap the CASIO WATCH+ icon.

Other than the above.If the phone does not respond after a fewseconds, it could mean that the phone islocated too far from the watch. Change toa different location and try again.

Q2 It takes some time before the phoneresponds.

The phone will emit a tone when a connectionis established with the watch, which takes afew seconds.

Q3 The phone cannot be found evenwhen it is close to the watch.

Since communication is performed usingradio waves, the watch may not be able to findthe phone even if it is within two meters.Certain environments may make theallowable communication range very short.


18

Auto Time Adjustment

Q1 When does the watch sync its timesetting with the phone?

The watch will connect with the phone andperform auto time adjustment at around 12:30a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. Theconnection is automatically terminated afterauto time adjustment is complete.

Q2 Auto time adjustment is performed,but the time setting is not correct.

Is auto time adjustment not beingperformed according to its normalschedule?

Note that auto time adjustment is notperformed for 24 hours after swapping ofthe Home Time and World Time, or afterthe time setting is adjusted manually onthe watch. Auto time adjustment willresume 24 hours after either of the aboveoperations is performed.

Is auto time adjustment enabled?Auto time adjustment will not beperformed at the scheduled times unlessit is enabled. Establish a connectionbetween the watch and phone, and thenuse CASIO WATCH+ to enable auto timeadjustment.l Using the Watch in a Medical Facility or

Aircraft

Is the watch’s battery charged sufficiently?The watch cannot connect with a phonewhile retrograde dial hand is pointing to“E”. Charge the watch.


Auto time adjustment will not start at thescheduled times if a stopwatch timemeasurement operation is in progress.Stop the measurement operation.

Q3 Time is not displayed correctly.The phone’s time setting may be incorrectbecause it is unable to connect with itsnetwork due to being out of range, etc. If thishappens, connect the phone to its networkand then adjust the time setting.

World Time

Q1 The time for a World Time City is notcorrect.

The summer time start date and time, end dateand time, or other rules were changed byauthorities.

Q2 After swapping your current location(Home City) time with the WorldTime, the World Time City time is notcorrect.

Use the CASIO WATCH+ to specify a WorldTime City.

Alarm

Q1 The alarm does not sound.

Is the watch’s battery charged?Keep the watch exposed to light until itrecharges sufficiently.l Solar Charging

The crown is pulled out.The alarm will not sound while the crownis pulled out. Push the crown back in to itsnormal position.

Is the alarm enabled?Enable the alarm.l Turning the Alarm On or Off

Hand Movement andIndications

Q1 I don’t know what mode the watch isin.

You tell which mode the watch is currently inby checking the position of the mode hand.l Navigating Between Modes● Hold down (A) for about two seconds to

enter the Calendar Mode.

30

Q2 Why can’t I perform any buttonoperations while high-speed handmovement is in progress?

Except for the mode navigation button, buttonoperation is disabled while high-speed handmovement is in progress after a watch settingis changed, etc. Wait until the hands stopmoving before performing button operations.

Q3 The second hand is jumping at two-second intervals.

Battery power is low. Keep the watch exposedto light until it recharges sufficiently.l Solar Charging

Q4 All hands are stopped at 12 o’clockand buttons do not work.

The battery is dead. Keep the watch exposedto light until the battery recharges sufficiently.l Solar Charging

Q5 The hands suddenly start moving athigh speed.

This is due to one of the reasons below, anddoes not indicate malfunction. Simply waituntil normal hand movement resumes.● The watch is recovering from a power

saving state.l Power Saving● Establish a connection with the phone and

correct the time setting.l Auto Time Adjustment

Q6 Hands are stopped and buttons donot work.

The watch is in the charge recovery mode.Wait until the recovery process is complete(for about 15 minutes). The watch will recovermore quickly if you place it in a brightly litlocation.

Q7 The indicated current time and dateare not correct.

Strong magnetism or impact can cause thehands and/or the indicator to go out ofalignment. Adjust hand and/or day indicatoralignment.l Adjusting Hand and Day Indicator

Alignment

Q8 The time setting is correct, but theday indicator is between days.

The day is in the process of changing. Forinformation about how the day changes, seethe section below.l Hands and the Day Indicator Movement


19

Crown Operations

Q1 Nothing happens when I rotate thecrown.

If you do not perform any operation for abouttwo minutes after pulling out the crown(approximately 30 minutes in the case of handand day indicator alignment), crownoperations will automatically becomedisabled. Push the crown back in to its normalposition and then pull it out again to re-enablecrown operations.l Using the Crown

Q2 Crown operation does not work.Crown operation is disabled while high-speedhand movement is in progress after a watchsetting is changed, etc. Wait until the handsstop moving before performing crownoperations.

Charging

Q1 The watch does not work eventhough it is exposed to light.

The watch stops operating whenever thebattery goes dead. Keep the watch exposedto light until it recharges sufficiently.l Solar Charging


20

Documents

MA1707-EB © 2017 CASIO COMPUTER CO., LTD. Operation Guide …