TECHNICAL DATA SHEETM8686

Continuous Filament Mat Designed for Phenolic Pultrusion

Description

This is a family of con�nuous filament reinforcing mats designed for phenolic pultrusion processes. They are treated with a suitable bonding resin and coupling agent and has good handling proper�es and weight uniformity.

This document is for reference only. Contact your sales manager for further informa�on.

This con�nuous filament mat is designed primarily for reinforcing pultruded shapes. This mat is characterized as having fast wet-through, good wet-out, and medium mat strength. This mat is normally used for pultrusion unless special requirements dictate using the following modifica�on.

Use

Available Products

Products

M8686

WeightAvailable Standard Weights *

Trimmed WidthAvailable Standard Widths *

Oz./Sq. Ft.

1.01.5

G/m2300450

Inches50.6850.68

Cen�meters127.172127.172

*All combination of non-standard weights and widths including any combinations not reflected in this table may be available only with prior approval of the product engineer.

Product Acceptance Limits & Test Methods

WEIGHT - Values stated are based on 12" x 12" or 30.48 cm x 30.48 cm test specimens.

Page 1/3

EDGE WEIGHT - Values stated are based on 2” x 12” or 5.08 cm x 30.48 cm test specimens.

1.001.50

Weight Per SquareFoot (Ounces)

Nominal Individual (Grams)

28.442.5

Tolerance (Grams)

+/- 2.98+/- 4.56

Test Method

W-01Fc

1.001.50

Weight Per SquareFoot (Ounces)

Nominal Individual (Grams)

4.87.0

Tolerance (Grams)

+/- 1.20+/- 1.75

Test Method

W-01-Fg-T

Page 2/3

TECHNICAL DATA SHEETM8686

This document is for reference only. Contact your sales manager for further informa�on.

Continuous Filament Mat Designed for Phenolic Pultrusion

TENSILE - Values stated are based on 3" x 12" or 7.62 cm x 30.48 cm test specimens.

Weight Per Square Foot

(Ounces)

1.001.50

Nominal

4044

------

Minimum Individual (Pounds)

2020

Test Method

S-01-AG-T

Maximum Individual (Pounds)

IGNITION LOSS (%)

WeightAll

Minimum Individual2.25

Maximum Individual6.75

Test MethodW-05-Ec-T

Weight Per Square Inches (Ounces)

As specified on the order +/- 1/8 +/- 3.175 D-03Aa

Nominal(Inches)

Tolerance(Inches)

Tolerance(Millimeters)

Test Method

All

WIDTH

ROLL-UP & TELESCOPING REQUIREMENTSThe mat is wound on a 4" (10.2 cm) inside diameter paper tube, having a single tube with a length the same as the mat width with the following tolerances:

For rolls 68” (172.7 cm) and greater, the tube length tolerances are plus 0", minus 1/2" (-1.27 cm) For rolls less than 68” (172.7 cm), the tube length tolerances are plus 0”, minus 1” (-2.54 cm)

*The mat will be so wound that the maximum length of mat telescoping will not exceed 1/4” (0.64 cm). Telescoping is described as the condi�on where successive wraps of mat are not perfectly aligned one upon the other, bringing about a concave effect on one end of the roll and a convex effect on the other.

No tube will protrude past the product.

Preparation for Shipment

Special Precautionary Note

In the event that Superior Hun�ngdon Composites or the customer has reason to suspect that a shipment may contain a contamina�on in any form, the party first suspec�ng such condi�on will no�fy the other and Superior Hun�ngdon Composites assumes responsibility for ini�a�ng appropriate ac�on. The use of the suspect material should be discon�nued, pending an inves�ga�on of the facts.

Significant Visual Properties

The con�nuous filament mat shall meet requirements as set forth in the visual standards maintained by the facility.

Page 3/3This document is for reference only. Contact your sales manager for further informa�on.

TECHNICAL DATA SHEETM8686

Continuous Filament Mat Designed for Phenolic Pultrusion

Product Identification

Cores will be printed on the inside to iden�fy type, ounces, and tracking.

A content label will adequately iden�fy each roll.

WRAPPINGThe rolls are wrapped in polyethylene.

Standard Packing Method

PACKAGINGThe rolls are mul�ple packed, twelve (individual or common) rolls for widths less than or equal to 42” (106.68 cm) or six (individual or common) rolls for other widths up to 84” (213.36 cm), on a 66” (167.64 cm) x 44” (111.76 cm) varying height pallet. Greater than 84” (213.36 cm) are on a 116” (294.6 cm) x 44” (111.76 cm) varying height pallet. Also, may be heat treated or block.

PALLETIZATIONThe rolls of mat will be palle�zed with pallet stretch packaging.

CONTINUOUS LENGTH ROLLSAll rolls will be con�nuous, one-piece lengths with no wrap-ins permi�ed.

APPROXIMATE FULL ROLL WEIGHT & LENGTH

Weight Per Square Foot (Ounces)

1.001.50

Approximate Full Weight (Kilograms)

1.32 x inches of mat width1.32 x inches of mat width

Approximate Full Roll Length (Feet)

550357

ROLL DIAMETERAll full rolls are manufactured to a diameter range of 19" (48.26 cm) to 22" (55.88 cm).

Note: A maximum of one (1) roll per pallet may be under 19" (48.26 cm), but not less than 9" (22.86 cm).

header tobottom of

title

Title to top of table

table bottom to asterisk text

bottom of textto bottom of title below

Subtitle to top of table

Bottom of title to bottomof subtitle below

bottom of text to bottomof subtitle below

space betweenphotos