Luxury Vinyl FlooringTechnical Information

Revolutionary, quick and easy flooring with the natural beauty of wood and stone

2 Clever Click

General Guidelines

Storage and transportationCartons should be stored and transported on a flat surface in neat stacks. Always store the cartons flat and never put them upright. Do not store the cartons in very cold (less than 2°C/35°F) or very warm (more than 40°C/104°F) or humid places.

Prior to fittingGeneral conditionsThe installation of Clever Click is straight forward and follows the same guidelines that apply to all quality resilient tile floors. Good preparation is essential for a trouble-free installation. Clever Click can be laid on concrete, timber, stone and many other subfloors, which have been suitably prepared.

Site conditions must comply with the relevant national regulations. Clever Click is not suitable for external installation or unheated locations but it can be used with under-floor heating providing it is switched off for 24 hours before and after laying (the maximum permitted surface temperature is 28C/81°F).

Following installation, Clever Click should be protected from heavy traffic for 24 hours and must not be washed for 24 hours. Always follow other manufacturers’ recommendations when using their proprietary materials for sub-floor preparation.

Visual inspectionPlease inspect product prior to installation. Check that the colours correspond to those ordered, the quantities are correct and there is no visible damage to the boxes. Check the vinyl planks or tiles during installation for any visible defects. Check that the tongue and groove of the click profile is free from dirt and undamaged. Do not install any planks or tiles that display any imperfections.

SuitabilityClever Click can be laid on concrete, cementitious screed, anhydrite (calcium sulphate), timber and ceramic tiles, which have been suitably prepared.

Clever Click can be used with traditional water based underfloor heating and cooling systems. If using electric wire systems please contact the manufacturer for correct installation methods.

Welcome to your brand new Clever Click design floor.

Clever Click is designed to offer all the stunning detail and outstanding beauty of natural materials, but with quick and easy installation.

For areas that are subject to extreme temperatures or to excessive direct heat source as fully glazed sun facing windows or conservatories we recommend that the Clever Click is installed with XtraFloor Flex Pro.

Moisture content of the subfloor Unheated cementitious screeds

less than 2.0CM%.

Underfloor heated cementitious screeds less than 1.8CM%.

Unheated anhydrite (calcium sulphate) screeds less than 0.5CM%.

Underfloor heated anhydrite (calcium sulphate) less than 0.3CM%.

Direct-to-earth concrete and stone subfloors must have an effective damp proof membrane (DPM). Follow manufacturer’s detailed instructions for the installation of a surface DPM and the use of levelling compound.

Temperature conditions before, during and after installationClever Click is best installed with a room temperature of between 18°C/64°F and 27°C/81°F and a floor temperature of above 15°C/59°F. Installations in areas colder than recommended will influence the convenience friendly installation properties of Clever Click.

The planks or tiles could be less easy to handle and less flexible, whilst cutting could be heavierwith small pieces difficult to cut out. The lower the temperature, the more difficult to handle.

For installation in areas warmer than recommended, we advise consultation with your local installer on how to create the appropriate installation conditions.

A constant temperature, fluctuating no more than 5°C per day and not below the required 18°C room temperature and 15°C floor temperature, should be maintained 24 hours before, during and 72 hours after installation.

AcclimatisationClever Click must acclimatise in the room of installation, or an equivalent area for at least 24 hours prior to installation, or until such time as the product has achieved an ambient temperature. Again, this is a minimum temperature of 18°C/64°F and a maximum of 27°C/81°F.

Unpack the Clever Click and check all planks or tiles in daylight for possible defects or discrepancies in colour.

Stack the plank or tiles in straight piles away from heating, cooling or windows with direct intense sunlight. This is to achieve a gradual acclimatisation.

Underfloor heatingClever Click can be used with traditional water based underfloor heating systems, provided there is a constant room temperature of 18°C/64°F for the acclimatisation period, installation and 72 hours after installation.

The underfloor heating must be gradually increased by increments of 5°C/41°F until it reaches the standard operating temperature conditions, with a maximum temperature of 27°C/81°F.

For suitability of the system please check the manufacturer’s instructions.

Contact with waterPrevent the floor from coming into contact with a large amount of water, or from being submerged,as the click connection is not fully waterproof.

4 Clever Click

General Guidelines

1 2

Step-by-step fitting instructionsThe surface beneath the floor must be sufficiently prepared in advance to guarantee successful fitting of the floor covering. In particular, it must be clean, dry, smooth, firm, level, free from defects and not contaminated with grease, oil or chemicals.

Clever Click is a “floating” floor. Never glue or fix the panels to the surface below. The flooring can be installed wall-to-wall, however in large areas (greater than 50m²) or where the floor may be exposed to unusually wide temperature ranges (such as where under floor heating is used, in a conservatory or areas adjacent to a south facing window), then it is advisable to use a 5mm space around the edge, as appropriate.

For surfaces larger than 50m², we advise that an expansion joint of 5mm is created around the perimeter of the room. In addition, should a single wall or run be longer than 10 linear metres, then a 5mm expansion joint should be allowed around the perimeter. If you are uncertain of the requirements, please contact your retailer who can confirm the exact requirements.

Fitting instructionsInstallation from one batchFor best results, mix at least two packs when fitting to avoid repetitions in the pattern. We recommend that you always use materials from a single production batch for each installation, as a match between batches cannot be guaranteed

Easy to cutClever Click planks or tiles are easily cut using a straight blade in a utility knife. Cut the printside of the plank or tile several times and snap along the line.

RECOMMENDED TOOLS Broom and / or vacuum

cleaner Tape measure Pencil Set square and ruler Utility knife Rubber mallet Tapping block

The Clever Click system panels can be joined in two different ways; either tongue-in-groove or groove-in-tongue. The simplest procedure, however, is groove-in-tongue. The advantage of the Clever Click system is that it allows you to choose your own starting position.

Moreover, you may work either from left to right or from right to left, whichever is best for you. Depending on the direction in which you work, you are advised to begin from either a corner or a door. It is advisable to begin with the groove side of the plank towards the wall and work from left to right.

1) Measure the room carefully todetermine the central axis, fromwhich the first row to be laid isoutlined.

2) Check whether the first row ofpanels needs to be narrowed.If not, the lower groove lip of thefirst row of panels need to beremoved. Use a utility knife toneatly cut off the lower groove lip.

3) Begin by laying the first row inthe corner of the room on yourleft hand side as you are lookingat the wall. Always work fromleft to right and with the tonguetowards yourself. (Figure 1).

4) Lay the first row in a straightline and click the head endstogether. Put the short side ofthe profile into head end ofthe previous panel and pressthe panel downwards. It isrecommended to use a rubbermallet for connecting thehead ends so that the joint fitssecurely. Continue laying the firstrow in the same way until youget to the last piece. (Figure 2).

5) For the last piece, measure thelast plank to ensure a tight fitto the wall. Then cut away themarked piece and fit the endpanel in the same way as theprevious panels. When cuttingthe panel with a utility knife,make sure that you cut throughthe wear layer before breakingthe panel. (Figure 3).

6) For an attractive and naturalappearance, we advise you to usethe piece left over from row 1 asthe first piece in the next row, aslong as the remaining piece is atleast 1/3 of the total plank length.Repeat for all subsequent rows.

7) Fit the second row as you didfor the first: start on the left sideand slide the groove of the panelunder an angle of about 25°overthe tongue of the previous rowand click the groove into thetongue by laying down the panelwhile pushing it firmly againstthe first row. (Figure 4).

8) Then fit the second panel bysliding the groove under at anangle of 25° into the tongueof the previous row. Positionthe corner of the head endagainst the previous panel andthen drop the short side of theprofile into the head end ofthe previous panel and pushdownwards. Use a rubber malletfor connecting the head ends sothat the joint fits securely.Repeat until you reach the endof the row.

9) To ensure a firm Click installation,it is recommended that theplanks are tapped togetheralong the long edge with atapping block and a rubbermallet. This will ensure that theClick mechanism is firmly lockedduring installation, providing asecure joint and avoiding anymovement after the installationhas been completed. (Figure 5)

10) To fit the last row of panelsyou will usually need to narrowthem. Do this as follows: lay apanel on top of the previousrow with the groove towards thewall, lay another panel upsidedown up to the edge of the walland mark the panel underneath.Cut the panel to size and fit thelast row. (Figure 6)

11) Door posts and heating pipesalso need to be individuallyfitted. First cut the panel to theright length. Then place thepanel next to the object anddraw the correct fitting. Next, cutthe panel to size. Doorposts canalso be sawn to size if necessaryto lay the floor beneath them.For cutting around difficult areassuch as door posts, heating pipesand other interior furniture; theuse of a Jigsaw with the correctplastic cutting blades is suitableand will avoid unsightly cuts atthe perimeter of the room.

Congratulations!You have just installed a Clever Click design floor. Your new floor has been produced in accordance with the highest standards and will give you years of pleasure in your home.

Although Clever Click design floors are one of the easiest floors to take care of, it is best to follow the recommendations, provided on page 6, for optimal protection of the factory finish and to keep your floor looking fresh.

3 4 5 6

6 Clever Click

All floors should be swept and dust mopped daily, following which soiling and marking can be removed using the appropriate method described here.

Before commencing work, put out signs to warn people that cleaning is in progress.

Daily sweeping and dust mopping1) Pick up litter and thoroughly

sweep the floor area.

2) Pick up debris with dustpan andbrush or vacuum.

3) Vacuum walk-off mats andcrevices at entrance(s).

Manual mopping – Ideal for small or congested areas.Manual mopping is used for soil removal in small or congested areas (including within large floors) and some mark removal. Spray cleaning may be required for heavier surface marking. (Note: In conditions of heavy soiling, perform a pre-wash by preparing a solution of Xtrafloor Cleaner Maintainer diluted in accordance with the label and pre-wash heavily soiled areas).

1) Using a two-bucket moppingsystem, apply solution usingwell-wrung mop to removesoiling.

2) Mop using overlapping strokes.

3) Rinse the mop frequently andchange the solution as necessary.

4) Allow entire floor area to drythoroughly.

5) Remove “Caution” signs.Ensure all equipment iscleaned thoroughly after useand stored safely.

Tips – Dealing with spills1) Spills of water, grease, food,

chemicals and other foreignmatter may cause the floor tobecome slippery.

2) Wipe up spills immediately withan absorbent cloth and thenwash thoroughly using XtrafloorSpot Remover as directed on thelabel or properly diluted XtrafloorCleaner Maintainer until the spillarea is completely clean.

3) Allow the floor to dry thoroughly.

Notes1) Clever Click products should not

be buffed with any pad moreabrasive than a red 3M pad (orequivalent).

2) Entrance mats, when properlyserviced, can effectively removeany abrasive and foreignmaterials from foot traffic andcut down on tracked in water.Clever recommend a minimumof two full strides of entrancematting.

Preventative maintenance1) Place non-rubber doormats at

entrances to stop large amountsof dirt from getting indoors.

2) Use felt under furniture andchair legs. Rolling office chairsshould be fitted with non-rubbercasters.

3) Clean the floor at least once aweek with a vacuum cleaner ormop. You will need to do thismore often if you use the floorintensively.

4) We advise that you only userecommended cleaningproducts, as aggressive cleaningproducts may damage the floor.

5) Stiletto heels can also damagethe floor.

6) Avoid long-lasting exposure todirect sunlight. Use curtains orblinds at peak times to minimisethe effect of direct sunlight.Most types of floor discolourunder the influence of directsunlight. To avoid colourdiscrepancies, you should movethe floor coverings present witha certain degree of regularity.

Starter KitThe starter kit is designed to keep your luxury vinyl floor looking its best for years to come.

Contents

1L cleaner maintainer

500ml floor spill cleaner, flat cap loose trigger

1 pack of felt pads

1 non-abrasive sponge/scourer

6 blue cleaning cloths

Promotional literature

Instruction sheet

General Floor Maintenance

Xtrafloor Cleaner MaintainerOur concentrated cleaner has a fresh aroma for routine cleaning. Suitable for use with all cleaning methods including manual, spray buffing and scrubber-drying. Availability: 1 ltr / 2.5 ltr.

Xtrafloor Spot RemoverA ready to use cleaner with a fresh aroma and formulated for removal of spills and other deposits. Availability: 500ml.

White Wash Pine 24115

Technical Information

Wood Stone

Product Information

Level of use EN 685 23 - 33 - 42 23 - 33 - 42Total thickness EN 428 ca. 4.50mm ca. 4.50mmWear layer EN 429 ca. 0.55mm ca. 0.55mmWear layer PUR treatment Superguard® Superguard®

Total weight kg/m2 EN 430 ca. 7.680 ca. 7.680

Size and Packaging

Planks A EN 427 191mm x 1316mm 324mm x 655mmBox Planks A 7 pcs / box 1.76m2 / box 1.49m2 / box

Test Results

Inflammability EN 13501 Bfl-S1 Bfl-S1Scratch resistance EN 660-2 Class T Class TSquareness & straightness EN 427 ≤ 0.35mm (Planks A) ≤ 0.35mm (Tiles)Slip resistance EN 13893 DS DSSlip restraint DIN 51130 R9 / R10 R9 / R10Residual indentation EN 433 ≤ 0.10 mm ≤ 0.10 mmFurniture leg resistance EN 424 No cracks, no damage No cracks, no damageCurling EN 434 ≤ 2mm ≤ 2mmElectrical resistance EN 1081 ≤ 109hm ≤ 109hmDimensional stability EN 434 Norm: ≤ 0.25%, average Norm: ≤ 0.25%, average

result measured: ≤ 0.05% result measured: ≤ 0.05%Heat insulation EN 12524 0.25w/(m.K) 0.25w/(m.K)Thermal resistance R ISO 8302 0.0159m2.K/W 0.0159m2.K/WElectrostatic performance EN 1815 < 2kV < 2kVFomaldehyde group EN 717-1 E1 E1Acoustic insulation ISO 717-1 4dB 4dB Castor chair resistance EN 425 No damage to wearlayer, No damage to wearlayer,

no de-lamination no de-laminationStain resistance EN 423 Very good Very goodLight fastness ISO 105-B02 ≥ 6 ≥ 6Underfloor heating EN 12524 Suitable, max 27°C Suitable, max 27°CResistance to chemicals EN 423 Very good Very goodWarranty 20 year Residential 20 year Residential

10 year Commercial 10 year Commercial