Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
L u m i n a r y S e r v o M o t i o n S e r i e s
Luminary Series Servo Drives provide the OEM market with a low cost but high performance servo drive for use in applications such as x-y tables, actuators, roll feeders, or any requirement where true position, velocity and torque control are desired. The Luminary Series is a cost competitive alternative to stepper control systems.
The versatile Luminary drives, LD-330 and the LD-500, are digitally controlled and will drive low cost servomotors up to 1000 watts. A standard analog input interface with encoder feedback provide the basic needs of a servomotor drive system. Input selectable velocity or torque mode provides real-time dynamic control. Optional adaptor cards can piggy-back onto the drive to provide various standard or custom digital control schemes. Currently the IIS drive network option card is available for multi-axis connectivity.
A development port connector, for access by the OEM, uses the ISOCOMM1 interface adapter. The ISOCOMM1 provides an isolated Rs232 connection to your PC.
Easy to use PC based L-Drive software for commissioning the system, available at no extra cost, is used for setting up motor/drive parameters and tuning the motor response to the load. Once set, the configuration firmware resides on the board giving the board the correct personality for the motor it will drive.
LD-330 and LD-500 Drive Features
Two Drive Sizes: 3.3 amp and 5.0 amp rms √continuous at 45 ° C
Integral Power Supply - Line input voltage range: √100 – 240vac
+/- 10v analog control input with sinusoidal drive √output for smooth torque and velocity control
Option card interface for customized OEM digital √drive communications
Four optically isolated 24vdc digital inputs √
Two optically isolated 24vdc digital outputs √
Motor encoder input, 5vdc, quadrature, ABZ/UVW √
Repeater output of encoder feedback for interfacing √to an analog position controller
Easy setup for your motor and drive configuration √
Optional: ISOCOMM1 - Factory communication √interface for updating firmware and motor parameters
Luminary Servo Drive
Choose from a variety of servomotor styles ranging from 30 watts to 1000 watts. Call now for free pre-sales motor sizing and selection support.
Industrial Indexing Systems, Inc. (585) 924-9181626 Fishers Run www.iis-servo.comVictor, NY 14564 [email protected]
AC Input Power
BUS Regen
Motor Encoder
Feedback
Motor Armature
Encoder Output
Analog 10 volt Input
Digital NetworkInterface
Setup Access Port --- J7
1
2
3
4
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
10
11
1
2
3
4
5
6
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
3
Inputs
Cons
ult F
acto
ry
LD-XXX/YYYYY
J8
J4
J6
J5
J3
J1
J2
Outputs
L2
L1
Earth
R
R
12
UVW
GND
U–
B–
A–
Z–
W–
A
B
Z
U
V
W
A–
B–
Z–
B
A
Z
Shield
+5VDC5v RET
Shield
Shield
In1+In1-In2+In2-In3+In3-In4+In4-
Out2+Out2-
Out1+Out1-
In1+In1-
Motor
Motor Encoder
V–
0.6001.800
4.3254.6005.330
0.200
0.250 1.8652.329
2.6033.270
4.1104.28
5.50 M3 TAP (8)
1.171
Mounting dimensions for board and power section.Mount to a metal structure for proper heat dissipation and lowest cost. Standard and custom mounting plates are also available.Interconnect diagram for the LD-330 and LD-500 drive
Industrial Indexing Systems, Inc. Version 1.2 www.iis-servo.com
Motor Encoder Feedback Connector
Analog input
Encoder output
Development port connection for drive setup and firmware updates
Motor Armature Connector
AC power input and BUS Regen Connector
Option Board Connector
I/O InterfaceFour 24vdc inputsTwo 24vdc outputs
Option Board Mounting Studs (3)
Connector layout of the LD-330 and LD-500 Luminary Drive
Overall Dimensions Width: 4.28 in Length: 5.50 in LD-330 Height: 2.00 in LD-500 Height: 2.40 in Mounting Standoff: M3 x 8mm Top Clearance: 0.5 in Side Clearance: 0.5 in