Lumin Smart Panel INSTALLATION MANUAL · ELECTRICIAN INTRODUCTION Welcome! The Lumin Smart Panel (LSP) is a stand-alone product that extends the capability of an existing circuit

Lumin Smart Panel

WWW.LUMINSMART.COM

INSTALLATION MANUAL

V3.2

® U.S. Registered Trademark. Patents pending. Copyright © 2020 Coulomb, Inc. (DBA Lumin). All rights reserved.

Lumin Smart Panel INSTALLATION MANUAL

TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Read Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Pre-Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Items In the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Tools You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Configuration & Account Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Limited Warranty for Lumin Smart Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

WARNING: HIGH VOLTAGE.

THE LUMIN SMART PANEL MUST BE INSTALLED BY A LICENSED ELECTRICIAN

INTRODUCTION Welcome! The Lumin Smart Panel (LSP) is a stand-alone product that extends the capability of an existing circuit breaker panel (or “electrical panel”) by providing measurement, control and automation of up to twelve (12) circuits in a home or building. The function of the circuit breaker panel remains the same and is not impacted. The LSP securely and safely transmits real-time consumption information to the cloud via Ethernet connection or customer Wi-Fi. The information can be accessed through a mobile or web app (software) for home/building owners. The Lumin app gives customers insights into their energy consumption and energy costs, as well as provides the user with the ability to control or automate their energy use remotely. This manual describes the physical installation of the LSP hardware. LSP registration and commissioning is typically done via the Lumin mobile app, which should be downloaded from the Apple App Store or Google Play Store prior to installation. Additional information regarding account configuration steps and options can be found at https://luminsmart.com/accountsetup. Need help? For installation assistance please contact Lumin by e-mail at [email protected] or by phone at 1-888-421-0616 (North America).

1

READ BEFORE USE The LSP is compatible with both flush-mounted (i.e. set within drywall) existing electrical panels and surface-mounted electrical panels. Please determine which electrical panel type the LSP will be connecting to and follow the corresponding installation steps outlined in this manual. The LSP must be installed indoors. Please review the product’s technical ratings and specifications (pg. 26) to confirm it is suitable for your application prior to installation. NOTE: The LSP Circuit Label & CT Table (provided with the LSP) must be completed and delivered to the home/building owner upon the successful installation of the LSP. A completed LSP Circuit Label & CT Table is required in order for users to set up their Lumin account. Warnings The LSP connects to dangerous voltages. The improper use or installation of the device can lead to serious or fatal injuries. Please observe the following safety precautions when installing the LSP: •  The product must be installed by a licensed electrician •  Review all the instructions before you start the installation •  Personal protective equipment should be worn when installing the product •  Do not use the product in any way other than its intended use •  Do not install or operate the product outdoors or in damp/wet conditions •  Do not install or operate the product in extreme temperatures •  Do not open, attempt to access or touch any internal product parts •  Do not use the product if it is damaged or appears to be damaged •  Use only the wires and cables supplied with the product •  Do not connect the product to circuit breakers rated higher than 60 amps •  Do not connect the product to any loads that exceed 1.5 horsepower •  Adhere to all local and national safety regulations for installation and use

2


PRE-INSTALLATION CHECKLIST Items in the Box

1 LSP with Conduit, Conduit Bushings & Wire Whips Attached

2 Mounting Brackets (Surface-mounted Installation)

NOTE: Additional items include an antenna, installation hardware, a LSP Circuit Label & CT Table, an Account Setup Guide and an Installation Overview.

3

1 Pair of 200A Current Transformers (A second pair is optional)

Drill Manual knockout

Phillips screwdriver

Tape measure Drywall Saw (optional)

Flathead screwdriver Level (optional)

Wire nuts

Wire stripper

PRE-INSTALLATION CHECKLIST Tools You’ll Need

4


NOTE: A supply-side connection (line-side tap) may be required for the LSP’s Grid Voltage Detector. Additional supplies may be required. See pg. 21 for more details.

INSTALLATION Installation Overview STEP 11. Connect a LSP wire labeled

“Line # Breaker” to the circuit breaker STEP 12. Connect a LSP wire labeled “Line # Load” to the load & turn circuit on STEP 13. Record circuit breaker name and phase (A or B) with corresponding LSP wire number STEP 14. Repeat steps 10-13 until all LSP Line # wires are connected STEP 15. Connect & then attach the 200A CTs to the main service lines STEP 16. Connect the LSP’s grid voltage wires to a portion of the electrical system that will be de-energized in a grid outage STEP 17. Replace the electrical panel cover

STEP 1. Turn off main feed & remove the electrical panel cover STEP 2 (Flush-mount Only). Cutout & remove drywall for LSP access STEP 3. Knock out a 2” hole in the electrical panel STEP 4. Measure & mark hole locations for mounting the LSP STEP 5 (Surface-mount Only). Secure mounting brackets to the wall STEP 6. Attach the LSP”s antenna and guide the LSP’s wire whip through the electrical panel STEP 7. Secure the LSP to the wall/bracket & electrical panel STEP 8. Connect the LSP ground wire to the ground bar STEP 9. Connect the LSP power cable harness STEP 10. Select a circuit breaker, turn it off & disconnect the load

5

Tools: Screwdriver

Installation Steps STEP 1.

6



Turn Off Main Feed and Remove Electrical Panel Cover

STEP 2 (Flush-Mount Only). Cutout and Remove Drywall

Tools: Tape measure, level (optional) and drywall saw or suitable alternative NOTE: Cut and remove enough drywall to accommodate the LSP’s wire whips. Consider drywall cutout “Option B” if additional space is required to accommodate the LSP’s wire whips and to properly access the electrical panel to complete Step 3.

Drywall Cutout Option A Drywall Cutout Option B

7

STEP 3.

Tools: Knockout punch or suitable alternative NOTE: Exact hole location in electrical panel may very depending on spacing constraints; place the hole location below, above or to either side of the electrical panel as needed to avoid any existing obstructions.


8


Knock Out One 2” Hole in Electrical Panel for 2” Conduit

STEP 4. Measure and Mark Hole Locations for Mounting the LSP

Tools: Tape measure and level (optional) NOTE: Ensure to mark the applicable hole locations for your installation type (flush-mount vs. surface-mount mounting brackets). Exact hole locations may vary depending on existing conditions.

Surface-mounted installation Flush-mounted installation

9

STEP 5 (Surface-mount Only). Secure Mounting Brackets to Wall

Tools: Drill, screws (x4) and washers (x4)

10


STEP 6.

NOTE: Attach the LSP’s antenna (provided with your LSP) and then guide the wire whip through the hole in the electrical panel. Remove the conduit bushing before guiding the wire whip through the hole.


11


Attach the LSP’s Antenna and Guide the LSP’s Wire Whip Through the Electrical Panel

Attach Antenna

Attach Antenna

STEP 7. Secure the LSP to the Wall/Bracket and Electrical Panel

Tools: Drill, screws (x4), washers (x4) and nuts (x4: surface-mount only) NOTE: Lift the LSP to align with the mounting holes and secure it directly to the wall (flush-mount installation) or mounting brackets (surface-mount installation) utilizing the hardware provided. Secure the LSP to the electrical panel with the 2” conduit bushing provided.


12



STEP 8. Connect the LSP Ground Wire to the Ground Bar

Tools: Screwdriver NOTE: Connect the bare copper ground wire from the LSP to the existing ground bar in the electrical panel (exact location of ground bar may vary).

13


Ground Wire

STEP 9. Connect the LSP Power Cable Harness

14


Neutral (white)

Line A (black) to Phase A Breaker

Line B (red) to Phase B Breaker

Tools: Screwdriver and wire stripper NOTE: Connect the LSP wire labeled “Neutral” to the existing neutral bar in the electrical panel; connect LSP wires labeled “Line A” and “Line B” to phase A and phase B breakers, respectively via a spare 2-pole breaker, a three-way wire nut (pigtail) to existing wiring, or double-tap the breaker if the breaker is listed for such use (DO NOT USE GFCI BREAKERS). The LSP draws ~5 watts and can be accommodated on almost any circuit breaker.


STEP 10.

Tools: Screwdriver

15


Disconnect Load

Select A Circuit Breaker to Connect to the LSP, Turn it Off and Disconnect Load

Turn Off Circuit

STEP 11.

Line # Breaker

Tools: Screwdriver and wire stripper NOTE: All LSP wires labeled “Line # Breaker” must connect to a breaker. Lines 1-6 (6 AWG wire) can connect to circuit breakers rated up to 60 amps and lines 7-12 (10 AWG wire) can connect to circuit breakers rated up to 30 amps. DO NOT connect the LSP to loads that exceed 1.5 horsepower.

16



Connect a LSP Wire Labeled “Line # Breaker” to the Circuit Breaker

STEP 12.

Line # Load

Tools: Wire stripper and wire nut NOTE: All LSP wires labeled “Line # Load” must connect to a load wire via a wire nut. The LSP wire number should match the wire number used in the previous step (ex. “Line 3 Breaker” connects to a breaker & “Line 3 Load” connects to that breaker’s load wire).

17


Connect a LSP Wire Labeled “Line # Load” to the Load and Then Turn the Circuit Breaker Back On

LSP LINE

#

PHASE (circle one)

CIRCUIT BREAKER LABEL/NAME

LSP LINE

#

PHASE (circle one)

CIRCUIT BREAKER LABEL/NAME

1 A

7 A

B B

2 A

8 A

B B

3 A

9 A

B B

4 A

10 A

B B

5 A

11 A

B B

6 A

12 A

B B

CURRENT TRANSFORMER (CT) CURRENT TRANSFORMER (CT)

Line A/B CTs Aux. A/B CTs (Optional)

STEP 13.

NOTE: Record the circuit label/name and phase (A or B) with the corresponding LSP line number in the LSP Circuit Label & CT Table provided (ex. record “Refrigerator” next to LSP Line 1 and circle Phase A if the circuit labeled “refrigerator” is on phase A and is connected to the LSP’s Line 1). Dual pole circuit breakers will require two LSP line numbers.

18


Refrigerator

Record Circuit Label/Name and Phase (A/B) With the Corresponding LSP Wire Number

STEP 14. Repeat Steps 10-13 Until All LSP Line # Wires Are Connected

Tools: Screwdriver, wire stripper and wire nuts NOTE: The LSP can connect to up to 12 single-pole (or six dual-pole) circuit breakers.

X 12


19

STEP 15.

NOTE: Connect the CTs labeled “Line A/B CT” to their corresponding LSP connector and then attach to the main service lines. The CT marked with “A” should attach to phase A and the CT marked with “B” should attach to phase B. Make sure “K” on the CT is facing toward the grid. The configuration above is only for installations without auxiliary CTs. If you ordered a second set of CTs, please contact Lumin Support or open the menu in the Lumin mobile app and navigate to “Quick Tips” to get information about appropriate auxiliary CT configurations.



Line B CT

Line A CT

20

Phase B Phase A

Connect the 200A Current Transformers (CTs) Labeled “Line A/B CT” and then Attach to The Electrical Panel’s Main Service Lines

WARNING: To Avoid Equipment Damage, CTs Must Be Connected to the LSP Before Clamping to Live Wires.

STEP 16.

21


Grid Line (black)

Grid Neutral (white)

Connect black wire to a portion of the electrical system that will lose power in a grid outage

Connect the LSP’s Grid Voltage Detector Wires to the Grid Side of an Automatic Transfer Switch (ATS), Microgrid Interconnection Device (MID) or Main Distribution Panel

Tools: Wire stripper and wire nuts NOTE: The GVD monitors the presence of grid power. The GVD must be installed so that it is not backed up by storage. Land the Grid Neutral wire at the most upstream neutral bar or terminal possible. Extend the Grid Line wire via wire nut (or suitable alternative) and land it on non-backed-up circuit breaker or perform a supply-side connection (or “line-side tap”) on a wire that will lose power in a grid outage. Information about proper supply-side connections is available in the Quick Tips section of the Lumin mobile app.

STEP 17.


Tools: Screwdriver NOTE: Please make any necessary drywall repairs (if applicable) and clean up the area around the circuit breaker panel once the LSP installation is completed. Make sure the LSP’s antenna is securely attached prior to powering on the device.



22

Replace the Electrical Panel Cover

CONFIGURATION & ACCOUNT SETUP Once the installation of your LSP is completed, please utilize the Lumin mobile app, consult the Account Setup Guide provided with your LSP or go to https://luminsmart.com/accountsetup to establish a user account and set up the Lumin software for use with your LSP. You will need the completed LSP Circuit Label & CT Table to complete the account setup process. For account setup assistance or troubleshooting, please call 1-888-421-0616 (North America) or e-mail [email protected].

23

PRODUCT SPECIFICATIONS

ENVIRONMENTAL SPECIFICATIONS COMPATABILITY & COMPLIANCE

Operating Temperature -20°C to 60°C (-4°F to 140°F)

Panel

Any manufacturer

Enclosure Type Rittal KL 1511.510 Breakers Any manufacturer

RoHS Compliant Yes Compliance UL 916/61010

PHYSICAL SPECIFICATIONS INSTALLATION

Dimensions 40.0cm x 40.0cm x 12.0cm Licensed electrician Required

Weight 15.2kg Type Indoor wall mount

Conductor Length 50.8cm Time 2-3 hours

PERFORMANCE SPECIFICATION SUPPORTED CIRCUIT BREAKERS & LOADS

AC Voltage 120/240V Amperage 6 channels up to 60A 6 channels up to 30A

Feed-In Type Single & Dual Phase # of Circuit Breakers Up to 12

Warranty 10 Year Limited Warranty Up to 4 Split Core Current Transformers

2 x 200A (main service) 2 x 200A or 50A (auxiliary)

Energy Measurement Revenue Grade Connected Loads Up to 1.5HP

CONNECTIVITY & SECURITY ENERGY MEASUREMENT SPECIFICATIONS

Wi-Fi: 802.11b/g/n @ 2.4GHz with Internet access Each dedicated circuit metered separately

WEP 64, WEP 128, WPA and WPA2 encryption methods Dual phase voltage measurement

DHCP (dynamic) or static IP addressing ANSI C12.20 0.5 Accuracy Class

X.509 certificate encryption Ability to determine loads less than 1.0W

Cryptographic protocol: TLS RFC 6176 20 kHz sampling frequency per circuit

AWS Multi-Region High Availability Class 3 PCB Assembly


24

LIMITED WARRANTY FOR LUMIN SMART PANEL This Limited Warranty gives you specific legal rights and you may also have other rights, which vary from state to state. The Limited Warranty can also be found online at https://luminsmart.com/legal/warranty and in the documentation we provide with the product. We warrant that during the warranty period, the product will be free from defects in materials and workmanship. We limit the duration and remedies of all implied warranties, including without limitation the warranties of merchantability and fitness for a particular purpose to the duration of this express limited warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Our responsibility for defective goods is limited to repair, replacement, or refund as described below in this warranty statement. Who May Use This Warranty? Coulomb Inc. (d/b/a Lumin), a Delaware corporation located at address 212 East Main Street, Suite 202, Charlottesville, VA 22902 (“we”) extends this limited warranty only to the consumer who originally activated the product and connected it to a Lumin Account (through https://www.luminsmart.com/) and to any subsequent owner or other transferee of the product (“you”). What Does This Warranty Cover? This limited warranty covers defects in materials and workmanship of the Lumin Smart Panel (the “product”) for the Warranty Period as defined below. What Does This Warranty Not Cover? This limited warranty does not cover any damage due to: (a) transportation; (b) storage; (c) improper installation; (d) improper use; (e) failure to follow the product instructions or to perform any preventive maintenance; (f) failure to adhere to the product’s technical and performance specifications, including the product’s acceptable operating temperature and humidity ranges of -20 degrees Celsius to 60 degrees Celsius and 10-90% humidity, respectively; (g) modifications; (h) opening the Lumin Smart Panel or tampering with its internal components; (i) unauthorized repair; (j) normal wear and tear; or (k external causes such as accidents, abuse, flooding, lightning strikes, storms, or other actions or events beyond our reasonable control. This limited warranty also does not apply to the software, mobile applications, technology and services provided by Lumin which enable you to remotely access and view data that is collected, stored and transmitted by the product concerning electricity consumption and/or to remotely control electrical circuits which the product is connected to (the “Lumin Service”). Use of the Lumin Service is subject to and governed by the terms of the Lumin Service User Agreement, a copy of which can be accessed at www.lumin.com/legal/useragreement. Any warranties provided by Lumin with respect to the Lumin Service are only those warranties expressly set forth in the Lumin Service User Agreement What Is The Period Of Coverage? The “Warranty Period” for this limited warranty starts on the date the product is first activated and connected to a Lumin Account through https://www.luminsmart.com/) and lasts (a) for two years for the product’s sensor boards and the processor board, including the individual components that makeup the sensor boards and processor board, and (b) for ten years for all other components of the product. The Warranty Period is not extended if we repair or replace the product. We may change the availability of this limited warranty at our discretion, but any changes will not be retroactive. What Are Your Remedies Under This Warranty? With respect to any defective product during the applicable Warranty Period, we will, in our sole discretion, either: (a) repair or replace such product (or the defective part) free of charge or (b) refund the purchase price of such product. We will also pay for shipping and handling fees to return the repaired or replacement product to you if we elect to repair or replace the defective product. How Do You Obtain Warranty Service? To obtain warranty service, you must call 1-888-421-0616 or e-mail [email protected] during the Warranty Period to obtain a Defective Merchandise Authorization (“DMA”) number. No warranty service will be provided without a DMA number. Limitation of Liability. The remedies descried above are your sole and exclusive remedies and our entire liability for any breach of this limited warranty. Our liability shall under no circumstances exceed the actual amount paid by you for the defective product, nor shall we under any circumstances be liable for any consequential, incidental, special or punitive damages or losses, whether direct or indirect. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

25

This page intentionally left blank.



® U.S. Registered Trademark. Patents pending. Copyright © 2020 Coulomb, Inc. (DBA Lumin). All rights reserved.

[email protected]

1-888-421-0616

WWW.LUMINSMART.COM

Documents

Lumin Smart Panel INSTALLATION MANUAL · ELECTRICIAN INTRODUCTION Welcome! The Lumin Smart Panel (LSP) is a stand-alone product that extends the capability of an existing circuit