Upload
buiquynh
View
222
Download
0
Embed Size (px)
Citation preview
JN6676 LTE indoor CPE
www.jatontec.com 1
Product Specification
LTE Indoor CPE JN6676
LTE + 4*Gigabit LAN Ports+1*USB 2.0+1*FXS (Optional)+ WLAN 802.11b/g/n 300Mbps
+WLAN 802.11ac 867Mbps
Version 2.0
Copyright © 2015 by Jaton Technology Limited. All rights reserved.
JN6676 LTE indoor CPE
www.jatontec.com
2
1 Overview
1.1 Introduction
JN6676 indoor wireless router is one high performance indoor CPE platform. JN6676 has the
superior wireless access performance and comprehensive routing capabilities, which have
the abilities to bring the mobile operators or the vertical market to rapidly deploy wireless
services, achieve profitability as soon as possible.
1.2 Highlighted Features
LTE comply to 3GPP Release10 CAT6,
LTE TDD Band42/43
WI-FI 802.11b/g/n 2*2 [email protected]
WI-FI 802.11ac 2*2 MIMO@ 5.8GHz
supports a combined Wi-Fi speed of 1167 Mbps,
Support four 1000Mbps Ethernet LAN.
Support one FXS port for desk phone.
External USB port for USB HDD or LTE dongle use
Intuitive and convenient Web-based management.
Built-in LTE bipolar directional high gain antenna.
IPV6/IPV4 Dual Stack.
Support VoIP based upon SIP Protocol.
Support TR069 network management protocol.
User-friendly design of LED indicator.
JN6676 LTE indoor CPE
www.jatontec.com 3
2 Hardware Architecture
2.1 Interface and button
Connectors Description
Mini-PCIe Interface
Comply to mini-PCIe interface standard CEM1.2, the
interface is located inside the CPE, which can be accessed
in a variety of LTE modules
ETH RJ45 Four Giga LAN
POTS-RJ11 (Optional) 1 RJ11 interface, phone / fax / POS, providing VoIP
functions under conditions of software support
USB Type USB 2.0
USIM Slot Support 1.8V/3.0V USIM
Power The Power port is where you connect the enclosed power
adapter
Reset/Reboot Touch reset functions within 1s completed; long press over
5s to restore the factory settings
WPS Touch the WPS Button,WiFi successfully set
WiFi Turn on or off WiFi Function
2.2 Main Chipsets
Item Vendor Model & Edition
AP Chipset MediaTek MT7621+MT7603E+MT7612E
Modem Chipset GCT GDM7243QT
SPI Flash Spansion
MXIC 16MB
DDR2 Winbond
ETRONTECH 64MB
SLIC+Codec SiliconLabs Si32176C
2.3 Appearance
JN6676 LTE indoor CPE
www.jatontec.com
4
2.4 LED definitions
LED Name Description LED Behavior Status Indicator
POWER Power Indicator OFF No Power Supply
Steady On Power On
TEL(Optiona
l)
Voice telephone
interface indicator
OFF Not establish a connection with the
voice server
Blanking(1/sec.) registering with the voice server
Blinking(2
times/sec.)
Connection has been established and
is in a state with a hook or ringing voice
server
Steady On Be connected with voice server
LAN1 ~
LAN4
Gigabit ETH LAN
Indicator
OFF Connection is not established
Blinking Data being transmitted from LAN
Steady On Connection is established
WIFI WIFI Indicator
OFF WIFI function disable
Blanking Data being transmitted from WIFI
Steady On WLAN function enable
WPS WiFi encryption with
one button
OFF WPS disable
Blinking WiFi terminal being accessing
Steady On WPS Enable
MODE Mode Indication
OFF No access in LTE network
Blinking LTE scan, connect, complete LTE
connectivity
Steady On LTE mode, in LTE network
Signal
strength
Signal strength
indication
OFF No access in wireless network
One by one signal
bar display, four
bars
Displays the current LTE wireless
network signal strength, the more
stronger the signal, the more bars on.
JN6676 LTE indoor CPE
www.jatontec.com 5
3 Hardware Features Below table describes hardware features of JN6676.
Item Description
Network Supported
LTE FDD B3/7/20
LTE TDD B40/41/42/43
WIFI 802.11b/g/[email protected]
WIFI [email protected]
Power Class LTE +23dBm
LTE Antenna
Support built-in antenna or external antenna
Support 2T4R
Dual antenna, gain:7dBi for B42
antenna isolation:> 8dB
WiFi Antenna
Frequency:2400MHz~2483MHz;
VSWR: <2
Antenna efficiency: >50%(All frequencies)
Antenna Gain: 2dBi(3D Peak)
Antenna Isolation: >15dB
Support 2T2R
Built in antenna
Frequency:5150MHz~5825MHz;
VSWR: <2
Antenna efficiency: >50%(All frequencies)
Antenna Gain: 3dBi(3D Peak)
Antenna Isolation: >15dB
Support 2T2R
Built in antenna
WiFi Power Output
WiFi Power configuration(Default):
802.11b: 16dBm
802.11g: 14dBm
802.11n: 14dBm
802.11ac: 12dBm
WiFi Sensitivity
-76 dBm@11Mbit/s, typical for 802.11b
-65 dBm@54Mbit/s, typical for 802.11g
-67 dBm@20MHz, typical for 802.11n
-65 dBm@40MHz, typical for 802.11n
-85dBm@80MHz, typical for 802.11ac
-85dBm@160MHz, typical for 802.11ac
Power supply 12V/1.5ADC
SIM/USIM Card Slot Standard SIM card interface, in line with the 3GPP31.101 and
31.102
Reset Button
RJ45 4*Gigabit LAN
LED Power /TEL/LAN(4) /WiFi /WPS/Signal strength(4 bars)
JN6676 LTE indoor CPE
www.jatontec.com
6
4 Software Features Below table describes software features of JN6676.
Spec Description
Functions
Support 802.11 b/g/n/ac
Built in mini-PCIe interface supports a variety of wireless
modules
WAN port packet
forwarding capability:>
80Mbps
WAN port packet forwarding capability:> 80Mbps
Support modify the APN manually by WEB UI
WEB UI support OS: Windows XP above SP3, Window 7,
Vista, Linux。
Security
User Name/Password configuration
L2/L3 Firewall
-Basic firewall
- Port Forwarding
-uPnP
-DMZ
-Remote WAN Ping
-Remote Web Access Control
WIFI Features
1. Users can switch WLAN function through two ways, one is
touch the WLAN button, the second is Web UI.
2. Support configuration WLAN functions through Web UI,
include: SSID, SSID broadcasting turn on/off, AP Isolate
function, Channel, rate and mode
3. Support encryption: Un-encrypted, WEP-OPEN,
WEP-SHARED, WPA-PSK (TKIP), WPA-PSK (AES),
WPA2-PSK (TKIP), WPA2-PSK (AES)
4. Support WPS: Support PBC mode
5. WiFi protocol support:
IEEE WLAN 802.11b/g/n (2.401 – 2.483 GHz)
IEEE WLAN 802.11ac (5.150~5.825GHz)
JN6676 LTE indoor CPE
www.jatontec.com 7
Spec Description
Device Management
Device management:Support TR069
1. Supports upload / download the ACS specified file;
Support download CPE configuration file;
2. Support queries following parameters: PCI / RSRP / RSRQ
/ SINR / Transmit power / DL Packet Error Rate (PER) / MCS
Data rate in downlink and uplink / MIMO mode in progress
3. Support configure the following parameters: Wan
Configuration: Operation Mode, WAN Protocol, Get IP
Method, WAN IP Address, WAN IP Subnet Mask, MTU;
DHCP Server Configuration: DHCP Mode, Start IP, End IP,
Lease Time, Relay IP;
DMZ configuration: DMZ Host;
4. Support remote upgrade: Support batch or for individual
CPE remote version upgrade and rollback operations;
5. Support CPE version update
6. Supports debugging operations: reboot, restore factory
settings, remote PING bag, burn and change ACL address
7. Support cycle monitor: According to the server
instructions, periodically reporting corresponding parameters:
including device performance(Data rate in downlink and
uplink, DL Packet Error Rate (PER), MCS, MIMO mode, etc.)
and RF parameters (PCI, RSRP, RSRQ , SINR, Transmit
power, etc.)
Router Functions
1. Support Router mode and Bridge mode;
2. Users can automatically obtain IP parameters through
static IP or dynamic mode (DNS)
3. Users can automatically obtain IP address through DHCP;
4. Supports user devices via a switch connected to the
Internet by CPE LAN ports, maximum number of connections
no less than 32;
5. Support via a router device connected to the Internet by
CPE LAN ports.
JN6676 LTE indoor CPE
www.jatontec.com
8
Spec Description
Web UI Basic Function
1. Query and display functions:
A) Connection information (connection status, wireless
signal strength, network traffic statistics, connection time);
B) Basic information about the device firmware;
C) Board / Device SN;
D) SIM card information display such as IMEI, business
IP;
E) CPE connection status and parameter display;
2. Parameter configuration features:
A) The default login address 192.168.1.1
username / password: admin / admin;
B) Support modify password after login;
C) Support data traffic display, support clear the traffic
statistics;
D) Support local upgrade by Web UI;
E) Support restart and restore the factory settings;
support import and export configuration files;
F) Support setting WiFi , TR069, network access
parameters, firewall, system time, Router settings, fax, etc.;
G) Supports setup wizard;
Below table shows VOIP Specification (Optional) of JN6676.
No
.
Feature Status Comments
1 Protocol
SIP v2 (RFC 3261)
(SIP:Session Initiation Protocol)
(RFC:Request For Comments )
SDP (RFC2327)
(SDP :Session Description Protocol)
RTP/RTCP (RFC1889/RFC 1890)
(RTP:Realtime Transport Protocol)
( RTCP : Realtime Transport Control
Protocol)
Support 1
2 Codecs
G.711
G.729 a/b
Support 1
3 Echo Cancellation
G.168 Support
JN6676 LTE indoor CPE
www.jatontec.com 9
4 Caller ID Support Caller ID is a feature that
allows you to know who is
calling you before answering
the phone.
5 Call Hold Support
6 Outgoing Caller ID block Support Hide caller name and number
7 Anonymous Incoming Call Rejection Support It prevents anonymous calls
from getting through
8 Call Waiting Indication (tone) Support
9 Call Transfer – Blind Support
10 Call Transfer – Consultive Support
11 Call Forwarding – Unconditional
(Universal)
Support
12 Call Forwarding on No Answer Support
13 Call Forwarding on Busy Support
14 Call Waiting Support
15 Cancel Call Waiting Support
16 Cancel Call Waiting Support
17 Cancel Call Waiting Support
18 Cancel Call Waiting Support
19 Cancel Call Waiting Support
20 Call Waiting Recall Support When user have received call
waiting and then hang up, the
phone will play ringing tone to
indicate that there is another
call on line.
21 Three-way Conference Support Can speak to two other
persons at the same time,
making a three-person
conversation.
22 Dial Plan Support Support Defines the pattern that an
end user can dial to create a
valid phone number. It is
ordered set of regular
JN6676 LTE indoor CPE
www.jatontec.com
10
expressions.
23 Do Not Disturb Support
24 Redial Support
25 Repeat Dialing on Busy Support
26 Automatic Call Return Support Allows you to call back the
number whose call you
missed by simply pressing
some buttons.
27 G.711 fax send an receive Support
28 T.38 fax send an receive Support
29 MWI and VMWI
Support When the user has new
messages waiting for him, an
audible or visible indication is
operated on the phone.
JN6676 LTE indoor CPE
www.jatontec.com 11
4 Specifications and Environmental
4.1 Mechanical
Dimension: 167(H)× 187(W)× 44(T)mm
Package Weight: 400g
Color: Black or other customization color
4.2 Electrical
4.2.1 Power adapter
Input: 220 VAC, 50/60Hz
Output: 12V/1.5ADC
4.2.2 Heat & Power Dissipation
Power: <10W
4.3 Electromagnetic Compatibility
The Mercury is complied with ETSI standards.
4.4 Environmental
Item Description
Temperature Operation Temperature: -10 ºC~45 ºC
Storage Temperature: -20 ºC~70 ºC
Humidity Operation Humidity: 0%~95%
Storage Humidity: 0%~95%
Lightening Protection Differential mode: ±1kV(1.2/50us,differential pairs);
Common mode: ±1.5kV (1.2/50us, 8 line to ground)
Atmospheric Pressure 86kPa ~ 106kPa
Vibration IEC 68-2-36, IEC 68-2-6
Shock IEC 68-2-29
Drop IEC 68-2-32
JN6676 LTE indoor CPE
www.jatontec.com
12
5 Standard Package
Accessories can be customized.
Item Description
JN6676 Indoor CPE 1 PCS
12V/1A Power Adapter(wall mount) 1 PCS
User Manual 1 PCS
Ethernet cable 1 PCS
JN6676 LTE indoor CPE
www.jatontec.com 13
6 Approvals & Certifications
Item Description
Environmental standards RoHS
Certification CCC/CE/FCC( to be certificating)