LP-Gas EquiPmEnt and accEssoriEs - Emerson · Your local LP-Gas Equipment Distributor can assist you in selecting the proper regulators and ... Male ACMe Adaptor Female ACMe Filler

157

LP-Gas EquiPmEnt and accEssoriEs

Completing the hardware needs of an LP-Gas installation is a variety of accessories and tools. Regulators and relief valves often require vents assemblies and vent protectors. Installing a system can require many connection couplings, adaptors with or without screens, filters, swivels, plugs, test blocks, test gauges, tees, and mounting brackets. Also, level gauges and thermometers are required on some installations.

The following Accessory section provides descriptions and selection information for accessories available for regulators and valves. Your local LP-Gas Equipment Distributor can assist you in selecting the proper regulators and accessories for your system.

158


RegulatoR accessoRies

pRoduct/function selection infoRmation

tYpical tYpe numBeR

50

Page 165

J500

Page 166

Y602

Page 167

p499

Page 167

p400

Page 168

Test Pressure Gauge for Appliance Line Pressure

1/4-Inch NPT or Female Hose

1/4-Inch MNPT; 0 to 300 psi; Ranges in

MPa, kg/cm2, BarPressure Gauge

Screened Vents for Regulators

Adaptor with Screen

3-Way Tee Blocks

1/4-Inch FNPT to 1-Inch MNPT

1/4-Inch Flare by 1/4-Inch MNPT for Regulators

such as 912 and 67C Series Regulators

POL or 1/4-Inch MNPT

159


RegulatoR accessoRies

pRoduct/function selection infoRmation

tYpical tYpe numBeR

p413

Page 168

p100

Page 168

p500

Page 169

p520l

Page 169

Tee Checks for 3-Way POL with Internal Check Disk

Female POL or 1/4-Inch Inverted Flare by Male POL or 1/4-Inch MNPT

Plug and Filter Assembly

Triangular, Bowtie, or Strap Design

Drill Size No. 80 through No. 50

1/4-Inch Inverted Flare

Regulator Mounting Brackets

Adjustable Orifice Reamer

160


BulK stoRage tanK and ValVe

accessoRies

pRoduct/function selection infoRmation tYpical tYpe numBeR

J31

Page 170

J400

Page 171

J700

Page 172

m455

Page 172

m270, m536

Page 173

m100, m631

Page 174

m140, m150, m160, m394, m640, m646

Page 175

Rotary Level Gauge for Stational or Mobile Tank

68 to 140-Inch (1727 to 3556 mm)

Lengths

3/4-Inch MNPT for FNPT Connection; with or

without Pressure GaugeLiquid Level Vent Valves

Container (Tank) Thermometer

Liquid Transfer Valve

Male ACMe Adaptor

Female ACMe Filler Couplings

Female ACMe Vapor Return Couplings

1/2-Inch MNPT; -40° to 120°F (-40° to 49°C)

3/4 by 3/4-Inch MNPT

1-1/4 by 1-1/4-Inch through 4-1/4 by 4-1/4-Inch

Male ACMe

1-1/4-Inch Female ACMe by 3/8-Inch MNPT through 4-1/4-Inch Female ACMe

by 3-Inch MNPT

1-1/4-Inch Female ACMe by 3/8-Inch MNPT through 2-1/4-Inch Female ACMe

by 1-1/4-Inch MNPT

161



accessoRies


m498, m529

Page 176

m498, m520

Page 177

t12655t0012 /1H291706562

Page 177

m611

Page 178

m390

Page 178

m301

Page 179

m450a

Page 180

Male ACMe By Female NPT Adaptors

1-1/4 through 4-1/4-Inch Male ACMe by 1/4 through

3-Inch FNPT

1-1/4 through 4-1/4-Inch Male ACMe by 1/2 through

3-Inch FNPT

O-Ring for Male Adaptors

Male ACMe by Male NPT Adaptors

Adaptor Caps

POL Filler Coupling

Single-Piece POL Adaptors

Filler Valve Adaptor

For 2-1/4 or 3-1/4-Inch Adaptors to Give a Better

Seal than Washers

2-1/4 through 4-1/4-Inch Female ACMe by

1-3/4 through 3-1/4-Inch Male ACMe

Soft-Nose Male POL by 1/4-Inch MNPT

Female or Male POL by 1/4 through 3/4-Inch NPT, by 3/8 or 1/2-Inch

SAe Flare

For Filler Valves with 1-3/4-Inch Male ACMe Filler Connection and a 3/4-Inch FNPT Outlet

m570

Page 180

1-3/4-Inch Female ACMe by 1-3/4-Inch Male ACMe

Filler Hose Adaptor with Back Check Valve

162



accessoRies


p104-24, p174

Page 180

m318a

Page 181

m318

Page 182

p306, p193

Page 184

p163a

Page 185

p313

Page 186

p650

Page 187

p314

Page 188

Relief Valve Pipeaway Adaptor for DOT

For Use with Types H282, H5112, H135, H160, H148,

and H173 Valves

With or without Wing Nut; 1/4-Inch MNPT or 9/16-Inch

UNF Left-Hand Thread

Swivel POL Adaptorwith Metal Seats

Soft-Nose POL Adaptor

Air Interlock Systems

Auxiliary Remote Cable Release for Internal Valves

Handle- or Cable-Operated Latch/Remote Release for

Internal Valves

Primary Cable Control for Internal Valves

Cable Control, Release Mechanism, and Cable

Assembly for Internal Valves

Straight or Angle Male POL by 1/4-Inch MNPT

For Bobtail or Transport Trucks

With 25 or 50 Foot (7,6 or 15,2 m) Cable

or without Cable

Built-In Fusible Link to Close Valve in

Case of Fire

4, 5, or 6-Inch (102, 137, or 152 mm)

Travel

For 1-1/4, 2, 3, and 4-Inch (DN 32, 50, 80, and 100)

Internal Valves

163



accessoRies


p613

Page 192

Pneumatic ActuatorFor Types C404-24 and

C414-24 Single Flanged Valve(s)

p539

Page 191

For Closing and Opening of N550 Series Snappy Joe®

emergency Shutoff Valves (eSVs)

Pneumatic Actuator

Pneumatic Actuator

For Types C407, C421, and C427 Valves

(2 and 3-Inch NPT Sizes)p639

Page 192

p623

Page 192

For Types C403-24 andC413-24 Double Flanged Valve(s)

Pneumatic Actuator

Pneumatic Actuator p326

Page 189

For All Fisher® 2 and 3-Inch NPT and 3-Inch

(DN 80) Flanged Internal Valves

p389

Page 189

Pneumatic ActuatorFor Use with

Type C407-10 Only

Pneumatic ActuatorFor Types C404-32 and

C804-32 4-Inch (DN 100) Single Flanged Valve(s)

p614

Page 194

p312

Page 189

Pneumatic Actuator For Type C404-32

Pneumatic ActuatorFor C407-10 Series

1-1/4-Inch NPT Internal Valves

p631

Page 195

164



accessoRies


p120B

Page 197

Spanner Wrench for Large Female ACMe Caps

and Couplings

For Use with 2-1/4through 4-1/4-Inch

ACMe Threads

m3162

Page 196

Swivel or Standard: 1/2-Inch MNPT through

4-1/4-Inch Female ACMe for 1/2 through

3-Inch Hose

Clamp Hose Couplings

Ring and Chain Assemblies

For 1-1/4 through 4-1/4-Inch ACMe Caps

or Dust Sealsp147

Page 198

p206

Page 197

For Types H110 through H732 Valves

Protective Caps for Relief Valves

Seals and Plugs for Female ACMe Threads m178, m239

Page 183

1-1/4 to 4-1/4-Inch Male ACMe, MPOL, or FPOL

m108

Page 183

Female ACMe Caps Hand or Wrench Installation

Fuse Plug

208º to 220ºF (98º to 104ºC) Melting

Temperature Available in 1/8 and 1/4-inch MNPT Sizes

t1140399982/t1033699982

Page 173

p327c, p327d

Page 190

Air CylinderFor N550 Series Snappy Joe®

(eSVs) Close and/or Open Positions

t1139599012

Page 185

For Primary Control (Open or Close the eSV) or an Auxiliary Remote Release (Close only)

4-Way Control Valve

165


introduction

50 Series test gauges are used to check appliance line pressure after a regulator has been installed.

Test Gauge Assembly Ordering Information

Type number rAnGe InleT cOnnecTIOn HOse plAsTIc ApprOxImATe weIGHT,

pOunds (kg)

50-20 to 35-inches w.c.

(0 to 87 mbar)

1/4-Inch MNPT No No 1 (0,5)

50P-2Female hose

Yes Yes 2 (0,9)

50P-5 Yes No 1.2 (0,5)

50 series test gauge assemblies

tYpe 50p-5tYpe 50-2

tYpe 50p-2

ordering guide

To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:

www.emersonprocess.com/regulators/lp

166


pressure Gauge Ordering InformationType number cOnnecTIOn lOcATIOn rAnGe

J500

Bottom

0 to 15 psig, 0.1 MPa, 1,0 bar

J501 0 to 30 psig, 0 to 2 kg/cm2

J502 0 to 60 psig, 0.4 MPa, 4,0 bar

J504 0 to 160 psig, 1.1 MPa, 11,0 bar

J505 0 to 300 psig, 2 MPa, 20,0 bar

J510

Back


J511 0 to 30 psig, 0.2 MPa, 2,0 bar

J512 0 to 60 psig, 0.4 MPa, 4,0 bar

J514 0 to 160 psig, 1.1 MPa, 11,0 bar

J516 0 to 300 psig, 2.0 MPa, 20,0 bar

J518 0 to 2 kg/cm2, 30 psig

J519 0 to 4 kg/cm2, 60 psig

J531Top


J532 0 to 160 psig, 1.1 MPa, 11,0 bar

J537

Back

0 to 30 psig, 0 to 2 kg/cm2

J539 0 to 11 kg/cm2, 160 psig

J541 0 to 60 psig (0 to 27,6 bar) for anhydrous ammonia (NH3) service

J542Bottom

0 to 400 psig (0 to 4,14 bar) (stainless steel) for LP-Gas and

anhydrous ammonia (NH3) service

J551 0 to 30 psig, 0.2 MPa, 2,0 bar

introduction

J500 Series pressure gauges for LP-Gas service are available with either a bottom, back, or top connection. Connection is 1/4-inch MNPT. The back connection makes a more compact assembly on installations where space is limited. Gauges with a top connection also are available. All gauges have a 2-inch (100 mm) diameter face and a steel case.

J500 series pressure gauges

tYpe J501 tYpe J510

ordering guide



167


introduction

Attached directly to the regulator vent connection to a regulator vent line, vent assemblies should be pointed downward on outdoor installations to avoid moisture build-up in the regulator spring case. Units with a stabilizer assembly are intended for regulators with stability problems. The stabilizer gives a restricted breathing rate under normal conditions, opening for rapid discharge when necessary.

Y602 series Vent assemblies

tYpe Y602-1 (umBRella tYpe) tYpe Y602-13 (angle tYpe)

Vent Assembly Ordering InformationsIze, IncHes sTAbIlIzer umbrellA Type AnGle Type

1/4 FNPTNo - - - - Type Y602-13

Yes - - - - Type Y602-14

Drive fit in 1/4 FNPT No Type Y602-12 - - - -

1/4 MNPT

No Type Y602-1 - - - -

Yes Type Y602-2 - - - -

No Type Y602-11 - - - -

3/8 FNPTNo - - - - Type Y602-5

Yes - - - - Type Y602-6

1/2 FNPT

No - - - - Type Y602-7

Yes - - - - Type Y602-8

No Type Y602-15 - - - -

3/4 FNPT No - - - - Type Y602-9

3/4 MNPTNo - - - - Type Y602-23

No Type Y602-10 - - - -

1 MNPT No - - - - TYpe Y602-25

type p499 adaptor with screen

introduction

Used to convert a 1/4-inch NPT inlet on regulators such as Types 912 and 67C Series to an inverted flare. The Type P499 is available in a 1/4-inch (6,4 mm) inverted flare x 1/4-inch MNPT.

tYpe p499

Adaptor with screen Ordering Information

Type number descrIpTIOn ApprOxImATe weIGHT,pOunds (g)

P499 1/4-inch I.F. x 1/4-inch MNPT adaptor with screen 0.06 (27,2)

ordering guide

To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:


168


types p400, p403, p410, p413, and p414 tee Blocks and checksintroduction

Tee blocks are a 3-way POL connection that allows connection of two containers to a regulator inlet.

Tee checks allow the connection of two containers to a regulator inlet. A check disk inside the Tee check body permits flow only from the container with the highest vapor pressure.

tYpe p400 tee BlocK tYpe p414 tee cHecK

Tee blocks and checks Ordering InformationpIGTAIl Or

pIpInG cOnnecTIOn, IncHes

reGulATOrcOnnecTIOn,

IncHes

Type Of mAnIfOldTee block

(without check) Tee check

Female POL

Female POL P403 - - - -

Male POL P400 P410

1/4 MNPT - - - - P413

1/4 Inverted Flare 1/4 MNPT - - - - P414

introduction

Mounting brackets are used to mount regulators securely to the container or to the side of a building.

mounting brackets Ordering Information

reGulATOr TypesbrAckeT sTyle Type number

Triangular bowtie strap

R622, R632, R642, and R622H P100A P100C - - - -

R122H, R222, and R232 P100A - - - - - - - -

912 P100A - - - - P102A

types p100a, p102a, and p100c mounting Brackets

tYpe p100atYpe p100c

ordering guide



169


introduction

The Type P500 plug keeps dirt and foreign material from entering change over assemblies like the Type R110. It has a 1/4-inch (6,4 mm) inverted flare. The Type P501 is intended for the inlet of the 67C Series regulators. The Type P501 prevents foreign material from reaching the regulator’s valve disk.

plug and filter Assembly Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (g)

P500 1/4-inch I.F. Male Plug 0.2 (90,7)

P501 1/4-inch NPT inlet filter for Type 67C Series 0.5 (227)

tYpe p500

types p500 and p501 plug and filter assembly

type p520l adjustable orifice Reamer

introduction

The Type P520L tapered reamer is calibrated for propane vapor by drill size. Use Type P520L to enlarge or clean out orifices on LP-Gas appliances ranging from drill size No. 80 to 50.

tYpe p520l

ordering guide



Orifice Reamer Ordering InformationType number drIll sIze ApprOxImATe weIGHT, pOunds (g)

P520L No. 80 to 50 0.5 (227)

170


introduction

Rotary gauges can be used on stationary or mobile tanks to visually indicate the amount of LP-Gas or Anhydrous ammonia (NH3) in the container. They are also used in filling the tank to the proper liquid level. On mobile applications and some large stationary storage tanks, hangers are recommended to support the horizontal length of the dip tube.

The gauge is operated by opening the small bleed orifice when the tube is in the vapor space of the tank. Moving the pointer on the dial causes the end of the tube to move until it contacts liquid in the container. At that point, discharge from the bleed orifice turns from vapor to liquid and the rotary gauge dial gives the volume percentage of liquid in the tank.

rotary Gauge Ordering Information

lenGTH, IncHes (mm)

lpG dIAl>1200

GAllOn

lpG dIAl≤1200

GAllOn

nH3 dIAl>1200

GAllOn

nO dIAl>1200

GAllOn

68(1,727) J31L-1 J31S-1 J31A-1 J31X-1

69 to 92(1,753 to 2,337) J31L-2 J31S-2 J31A-2 J31X-2

93 to 108 (2,362 to 2,743) J31L-3 J31S-3 J31A-3 J31X-3

109 to 140(2,769 to 3,556) J31L-3L J31S-3L J31A-3L J31X-3L

Dial only P323 P322 P324 - - -

J31 series Rotary gauges

J31 seRies

J31 Series consist of heavy duty gauges that minimize vibration effects (swaying, bouncing) by a long 68-inch (173 cm) stem tube extension. Gauges fit 1-inch (2,54 mm) coupling container connections.

All gauges have stem and dip tubes with an extra large inside diameter. This assures that the correct liquid level can be obtained quickly.

A nylon packing sleeve and a friction ring for the pointer indicator gives smooth rotation and long service life. Steel and stainless steel materials resist rust or corrosion.

ordering guide



171


liquid level Vent Valves

J415 Series with steel construction are for use on either LP-Gas or Anhydrous ammonia (NH3) service. Installed on large bulk storage tanks at the maximum filling level. Standard valve comes with a 3/4-inch MNPT container connection and two 1/4-inch FNPT side outlets.

Type J415-1 features the addition of a Type J402S liquid level vent valve and Type J542 [0 to 400 psig (0 to 27,6 bar)] pressure gauge installed.

Vent Valves and fixed maximum liquid level gauges

Used in all kinds of LP-Gas containers to give positive visual indication of liquid reaching the maximum allowable liquid level.

Types J402S and J403S do not have dip tubes and must be used in containers where a dip tube has been welded in. Stainless steel constructions are for corrosive service.

J400 series level Vent Valves Ordering InformationType number descrIpTIOn

J402S Stainless steel liquid level vent valve

J403S Stainless steel liquid level vent valve with dial

J408S Stainless steel fixed liquid level vent valve

J409S Stainless steel fixed liquid level vent valve with dial

J415 3/4-inch MNPT angle valve with 1/4-inch FNPT outlets

J415-1 3/4-inch FNPT angle valve with liquid level vent valve and 0 to 400 psig (0 to 27,6 bar) pressure gauge

J415-2 3/4-inch FNPT angle valve with liquid level vent valve and 0 to 300 psig (0 to 20,7) pressure gauge for LP-Gas

J400 series Vent Valves

tYpe J415

tYpe J403stYpe J402s

ordering guide



172


introduction

Suitable for any tank size in LP-Gas and Anhydrous ammonia (NH3) service, the 2-inch (51 mm) diameter dial reads from –40° to 120°F (–40° to 49°C). They are dustproof and waterproof. Specify Type J700 for a 1/2-inch threaded MNPT by a 4-inch (102 mm) length or Type J701 for a 1/2-inch threaded MNPT by 6-inch (152 mm) length.

container Thermometer block Ordering Information


J700 Thermometer with 4-inch (102 mm) stem0.05 (22,7)

J701 Thermometer with 6-inch (152 mm) stem

J700 series container thermometers

type m455 liquid transfer Valve

introduction

The Type M455 is a special 3/4-inch MNPT inlet by 3/4-inch MNPT outlet valve. It opens the tank’s liquid withdrawal valve the correct distance to permit transfer operations. A nylon gasket is supplied for a tight seal with the withdrawal valve.

liquid Transfer Valve Ordering Information


M455 3/4-inch MNPT x 3/4-inch MNPT for Type N456 inlet 0.3 (136)

tYpe J700

tYpe m455

ordering guide



173


male acme adaptors

male Acme Adaptor Ordering Information

mAle Acme, IncHes wAsHer drAwInG number

Type number

brass steel

1-1/4 x 1-1/4 1E8122 M270 - - -

1-3/4 X 1-3/4 1E8124 M273 M536-14

2-1/4 X 2-1/4 1E8126 - - - M536-18

3-1/4 X 3-1/4 1E8128 - - - M536-26

4-1/4 X 4-1/4 T10948 - - - M536-34

tYpe m270

ordering guide

introduction

Fuse Plugs, when installed in the actuator piping at the valve, will allow the pneumatic pressure to vent closing the valve if the plug is exposed to temperature above 208° to 220° F (98° to 104° C). Fuse plugs are available in two sizes, 1/8-inch NPT (T1140399982) and 1/4-inch NPT (T1033699982).

fuse plugs

fuse plug Ordering InformationpArT number sIze melTInG TemperATure

T1140399982 1/8-inch NPT208º to 220ºF (98º to 104ºC)

T1033699982 1/4-inch NPT



introduction

These adaptors are male ACME to male ACME in sizes 1-1/4 by 1-1/4-inch through 4-1/4 by 4-1/4-inch. Brass or steel construction.

174


female acme filler couplings

female Acme filler coupling Ordering Information

femAle Acme, IncHes OTHer cOnnecTIOn, IncHes lenGTH, IncHes (mm) fIGure reference

Type number

brass steel

1-1/43/8 MNPT 3 (76,0) 1 M100 - - -

1/2 MNPT 2-1/2 (64,0) 1 M101 - - -

1-3/4

1/2 MNPT 3 (76,0) 1 M110 - - -

3/4 MNPT3 (76,0) 1 M111 M631-6

6-1/8 (156) 2 - - - M635-6

1 MNPT3 (76,0) 1 M112 M631-8

7 (178) 2 - - - M635-8

2-1/4 1-1/4 MNPT 3-1/4 (83,0) 3 M120(1) M121

3-1/41-1/4 FNPT 1-1/2 (38,0) 4 M442 - - -

2 MNPT 3-3/4 (95,0) 3 M130(1) M133

4-1/4 3 MNPT 4-1/2 (114) 3 M664-24 M634-24

1. Steel nipple.

1 2

3 4

ordering guide



introduction

These couplings allow connection of ACME threads to NPT. One side is 1-1/4 through 4-1/4-inch female ACME. The other side is 3/8 through 3-inch NPT. Available in brass or steel.

175


female acme Vapor Return couplings

female Acme Vapor return coupling Ordering InformationfemAle Acme,

IncHes mAle npT, IncHes lenGTH, IncHes (mm) fIGurereference

Type number

brass steel

1-1/43/8

2-1/2 (76,0) 5 M140 - - -

6-1/4 (159) 6 M394 - - -

1/2 2-1/2 (64,0) 5 M141 M640-4

1-3/4

3/43-3/8 (86,0) 5 M150 - - -

7 (178) 6 - - - M646-6

13-1/4 (83,0) 5 M151 M641-8

7-3/8 (187) 6 - - - M646-8

2-1/4 1-1/4 3-3/8 (86,0) 7 M160 - - -

5

6

7

ordering guide



introduction

Vapor return couplings are available with 1-1/4 through 2-1/4-inch female ACME threads on one side and 3/8 through 1-1/4-inch male NPT threads on the other. Brass or steel construction.

176


male Acme by female npT Adaptors Ordering Information

mAle Acme, IncHes femAle npT, IncHes fIGurereference

wAsHer drAwInG number

Type number

brass steel

1-1/4

1/4 9 1E8122 M498-4/2 - - -

3/8 9 1E8122 M498-6/3 - - -

1/2 9 1E8122 M192 - - -

3/4 8 1E8122 M193 - - -

1-3/4

1/4 8 1E8124 M210 - - -

3/8 8 1E8124 M211 - - -

1/2 8 1E8124 M212 - - -

3/4 8 1E8124 M213 M526-6

1 8 1E8124 M214 M526-8

2-1/4

1 9 1E8126 M502-12/8 - - -

1-1/4 9 1E8126 M502-16/10 M522-16/10

1-1/2 9 1E8126 M502-16/12 - - -

3-1/4

1-1/4 8 1E8128 M250 - - -

2 8 1E8128 M252 M528-16

3 8 1E8128 M508-24 M528-24

4-1/4 3 8 T10948 M509-24 M529-24

male acme by female npt adaptors

98

ordering guide



introduction

These adaptors provide 1-1/4 through 4-1/4-inch male ACME on one side and 1/4 through 3/4-inch female NPT threads on the other side. Brass or steel construction.

177


male acme by male npt adaptors

male Acme by male npT Adaptors Ordering Information

mAle Acme, IncHes mAle npT, IncHes wAsHer drAwInG numberType number

brass steel

1-1/4

1/2 1E8122 M498-4/2 - - -

3/4 1E8122 M498-6/3 - - -

1 1E8122 - - - M520-8

1-3/4

1/2 1E8124 - - - M521-4

3/4 1E8124 M215 M521-6

1 1E8124 M216 M521-8

1-1/4 1E8124 M217 M521-10

2-1/4

1-1/4 1E8126 M233 M236

1-1/2 1E8126 M502-12/8 - - -

2 1E8126 M502-16/10 M522-16/10

3-1/42 1E8128 M503-16 M263

3 1E8128 M262 M523-24

4-1/4 3 T10948 M504-24 M524-24

o-Rings for male adaptorsintroduction

The 2-1/4 and 3-1/4-inch male adaptors listed above can be supplied with replacement O-rings instead of the conventional washer type of gasket. In most cases, O-rings give a tighter seal than the washers.

O-ring Ordering InformationO-rInG fOr mATerIAl pArT number

2-1/4-inch adaptors Nitrile (NBR) T12655T0012

3-1/4-inch adaptors Nitrile (NBR) 1H291706562

tYpe m498-4/2

ordering guide



introduction

Adaptors are 1-1/4-inch through 4-1/4-inch male ACME on one side and 1/2 through 3-inch male NPT on the other. Available in brass or steel.

178


adaptor caps

Adaptor cap Ordering Information

femAle Acme, IncHes mAle Acme, IncHesType number

brass ductile Iron

2-1/4 1-3/4 M611 - - -

3-1/4 1-3/4 M612 M622

4-1/4 3-1/4 M613 M623

tYpe m612

type m390 pol filler coupling

pOl filler coupling Ordering InformationreplAcemenT O-rInG mAle pOl mAle npT, IncHes lenGTH, IncHes (mm) Type number

T12945T0012 Soft nose 1/4 6 (152) M390

tYpe m390

ordering guide



introduction

6-inch (152 mm) male POL to 1/4-inch NPT male filler coupling. Brass construction. Replacement O-rings are available.

introduction

These caps are 2-1/4 through 4-1/4-inch female ACME on one side and 1-3/4 through 3-1/4-inch male ACME on the other. Available in brass or ductile iron.

179


m series single-piece pol adaptors

single-piece pOl Adaptor Ordering InformationpOl cOnnecTIOn OTHer cOnnecTIOn, IncHes fIGure reference Type number, brAss

Female POL

1/4 FNPT 1 M301

1/2 FNPT 1 M303

1/4 MNPT 2 M284

3/8 MNPT 2 M285

1/2 MNPT 2 M286

3/4 MNPT 2 M287

Male POL

1/2 FNPT 3 M357

3/8 SAE Flare 4 M353

1/2 SAE Flare 4 M355

1

3

2

4

ordering guide



introduction

These single-piece brass POL adaptors are available in four styles. Connections are 1/4 through 3/4-inch threaded NPT, 3/8-inch flare, and 1/2-inch NPT flare. Brass construction.

180


type m450a filler Valve adaptorintroduction

The Type M450A allows methanol to be added through conventional-design double back check filler valves with a 1-3/4-inch male ACME filler connection and a 3/4-inch FNPT outlet.

filler Hose Adaptor Ordering Information

Type number, brAss

fIller VAlVe cOnnecTIOn,

IncHes

fIller VAlVe cOnnecTIOn,

IncHes

ApprOxImATe weIGHT,

pOunds (kg)

M570 1-3/4 female ACME 1-3/4 male ACME 1.1 (0,5)

type m570 filler Hose adaptor with Back checkintroduction

Intended for the outlet of a bobtail truck filling hose, the Type M570 enables the filling hose to be removed if the filler valve fails to close. An integral back check in the adaptor prevents gas from escaping in the event of a failure of the filler valve. The filler valve should be repaired as soon as possible and the Type M570 removed from the filler valve.

relief Valve pipeaway Adaptor Ordering InformationpIpeAwAy AdApTOr sTyle Type number VAlVe Type

P104-24H282

H5112

P174

H135

H160

H148

H173

types p104-24 and p174 Relief Valve pipeaway adaptorsintroduction

DOT cylinder relief valves must be installed with a pipeaway adaptor to ensure that any discharge is directed away to a safe location.

tYpe m450a

tYpe m570

tYpe p104-24

filler Valve Adaptor Ordering Information

Type number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)

M450A 1 3/4-inch ACME x 3/4-inch NPT adaptor 2.1 (0,95)

ordering guideTo order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies

your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp

181


introduction

Three different soft nose (O-ring) POLs with or without a plastic wing nut are available. The wing nut attaches to the POL nut, giving a convenient way of connecting and disconnecting the regulator from the cylinder valve without the bother of a separate wrench.

types m318a, m318aW, and m388 soft-nose pol adaptors

pOl Adaptor Ordering InformationType

number

buIlT-Inexcess-flOw

VAlVe

OuTleT cOnnecTIOn,

IncHeswInG nuT

ApprOxImATe weIGHT,

pOunds (g)M318A

No1/4 MNPT

No 0.3 (136)

M388 No 0.5 (227)

M318AW 9/16 UNF LH Yes 0.3 (136)

Soft nose, replacement O-ring T12945T0012.

tYpe m318aW tYpe m318a

tYpe m388

ordering guide



182


introduction

POL adaptors with metal seats provide connections between the cylinder valve and the regulator inlet. A wrench is required to generate the required torque to create a metal to metal seal on the POL nose.

types m318, m322, and m345 swivel pol adaptors

swivel pOl Adaptor Ordering Information

Type number pOlcOnnecTIOn

OTHer cOnnecTIOn, IncHes

lenGTH,IncHes (mm)

ApprOxImATe weIGHT, pOunds (g)

M318 Straightmale POL 1/4 MNPT

2-3/8 (60)0.3 (136)

M322 3-1/2 (89)

M345 Angle male POL 1/4 MNPT 3 (76) 0.4 (181)

tYpe m318 tYpe m322

tYpe m345

ordering guide



183


introduction

ACME caps of various sizes and materials are used on male ACME threads to keep debris out of the piping systems. Small sizes are designed for hand tightening. Larger sizes are intended to be either tightened by hand or with the use of the Type P120B spanner wrench.

m108, m219, m431 series female acme caps

female Acme cap series Ordering Information

femAle Acme sIze, IncHesType number

plastic(1) brass steel

1-1/4 M108 - - - - - - - -

1-3/4 M109 M229(2) M219(2)

2-1/4 - - - - M431 M432

3-1/4 - - - - M441 M443

4-1/4 - - - - M605-34 M625-34

1. For LP-Gas only. 2. Add 1 suffix for Type P147 ring and chain.

tYpe m108 oR m109

tYpe m431

introduction

ACME plugs of various sizes and materials are used in female ACME threads to keep debris out of the piping systems.

seals and plugs

plug and seal Ordering InformationsIze, IncHes pluG dusT seAl

1-1/4 Male ACME - - - - Type M178 Plastic

1-3/4 Male ACME Type M239 Aluminum Type M179 Plastic



4-1/4 Male ACME Type M535-34 Steel - - - -

MPOL Type M412 Brass - - - -

FPOL Type M420 Brass - - - -

tYpe m229tYpe m219

tYpe m605-34

tYpe m178 tYpe m239 tYpe m412

ordering guideTo order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies

your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp

184


aiR inteRlocK HooK-up on tRanspoRt tRucK

air interlock systemsintroduction

An air interlock system can be configured for transport and bobtail trucks with air brakes by using air cylinder actuated internal valves. This system simultaneously interlocks the internal operation with the truck air brakes without affecting normal air brake operation. It complies with DOT MC331 and NFPA 58

requirements regarding thermal and remote release feasibility.

The air interlock system permits the air brakes to set before the internal valve opens – even if the truck operator forgets to set the brakes. The brakes cannot be released until the internal valve is closed.

Air Interlock system for Transport Trucks Ordering Information

number OfInTernAl VAlVes

IncludesType number4-way Hand Valves

T1007499982fuse plugs

T1033699982Vent screens0l078343062

2-way check ValveT1045699982

backpressure ValveT1045399012

1 2 3 2 1 1 P306

2 4 4 4 1 1 P307

3 5 5 5 1 1 P308

Air Interlock system for bobtail Trucks Ordering Information

Type OfbObTAIl Truck

number OfInTernAl VAlVes

IncludesType number4-way Hand Valves

T1139599012fuse plugs

T11403999822-way check Valve

T1045699982backpressure Valve

T1045399012<3500 gallons (13 249 liters) 1 1 2 1 1 P193

>3500 gallons(13 249 liters) 1 2 3 1 1 P194

Twin Barrel 2 3 3 1 1 P195

In addition, a 4–way actuating valve can be used with Type C404A-32 to pressure both sides of the air cylinder depending upon the position of the operating handle. This allows air pressure to close as well as to open the internal valve.

aiR inteRlocK sYstems foR BoBtail tRucKs

Brakeactuators(part of

brake system)

Relayvalve

Two-waycheck valve

Backpressurevalve Fuse

plugCylinderactuator

Service line

Internalvalve

Fuse plug

Emergency valve(hand valve)

Fuseplug

Four-wayactuating valve

For:

ZM GRAPHICS • 214-906-4162 • [email protected](c) 2007, ZM Graphics Usage: Unlimited within Emerson & Fisher

File name:

Placed file(s):

For page:

Updated by:

GCG, 817-332-4600

Last updated:

Fisher Tank / Emerson

Production notes:

2007 FISHER-TransportTruck.ai

None

Carol Zuber-Mallison09/24/2007

For:

ZM GRAPHICS • 214-906-4162 • [email protected](c) 2007, ZM Graphics Usage: Unlimited within Emerson & Fisher

File name:

Placed file(s):

For page:

Updated by:

GCG, 817-332-4600

Last updated:

Fisher Tank / Emerson

Production notes:

2007 FISHER-BobtailTruck.ai

None

Carol Zuber-Mallison09/24/2007

Brake actuators(part of truck

air brakesystem)

Reservoir(part of truck air brake system)

To Port 1 connectionon actuating valve

Line fromcompressor

(supply)

Brake line(service)

Relayvalve

Two-waycheck valve

Backpressurevalve

Cylinderactuator Internal

valve

Fuse plug

Emergencyvalve

(hand valve)

Four-wayactuating valve

Fuse plug

Fuseplug

185


type p163a and p164 series auxiliary Remote Releaseintroduction

Type P163A or P164A Auxiliary Remote Release – These units allow the internal valve to be closed from a location other than the primary control point (Type P650 or P651). Pulling the auxiliary release handle trips the release mechanism on the primary control to close the internal valve.

The two assemblies are identical except for the length. Type P163A has an untrimmed length of 25 feet (7,6 m) and Type P164A has an untrimmed length of 50 feet (15,2 m). Both cables can be trimmed to any length. Both releases can be installed through mounting brackets up to 3/8-inch (9,5 mm) thick.

tYpe p163a

tYpe p164c

ordering guide

t1139599012 4-Way control Valveintroduction

Fisher® makes available a control valve that can be used as primary control (open or close the ESV) or an auxiliary remote release (close only).

Placing the valve’s button in the upward position permits pressure to the cylinder. Pushing the button down exhausts pressure to close all valves connected to the system.

Type P164B — a release assembly that uses 50 ft (15 m) of cable housing which does not require elaborate guiding like uncovered cables.

Type P164C — an Auxiliary Remote Release without cable is also available.



Auxiliary remote release Ordering Information

Type number AuxIlIAry remOTe releAse fOr: lenGTH, feeT (m)

P163A P650 or P651 25 (7,6)

P164A P650 or P651 50 (15)

P164B N550 50 (15)

P164C - - - - No cable

4-way control Valve Ordering InformationType/pArT number TypIcAl use descrIpTIOn

T1139599012Control double-acting cylinder

or two single-acting on a selective basis

4-way push button valve

186


tYpe p313

p313 and p340 series latch/Remote Release mechanismsintroduction

With the exception of the 3-inch (DN 80) flanged sizes, all Fisher® brand internal valves can be fitted with a manual latch/remote release mechanism. When the internal valve’s operating lever is manually moved to the open position, the lever can be latched in the open position. The lever can be released from a remote location by pulling on the cable attached to a pull ring, thus closing the internal valve. A built-in fusible element in the latch/release melts if exposed to fire allowing the operating lever to return to the closed position.

Type P313– available factory installed, on the Type C404M32. The Type P315 remote release should be used with this release.

Type P340– easily installed in the field by removing two of the three gland cap screws.

Type P341 – available factory installed on the Type C407M10.

Type P342 – bi-directional latch/remote release allows operation from two directions.

tYpe p340

ordering guide



latch/remote release mechnisms Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)

P313 Manual lever and release for C404-32 12 (5,4)

P340 Fuse latch for internal valve 0.3 (0,1)

P341 Latch/Remote release for C407-10 1 (0,5)

P342 Dual latch/remote release for C407-10 1 (0,5)

187


p650 series primary cable controlintroduction

Type P650 or P651 Primary Cable Control is capable of actuating all Fisher® internal valves except the 4-inch (DN 100) Type C404-32, the Type P650 or P651 opens and closes the valve from a remote point, usually the rear of the bobtail or transport. Pulling the handle of the primary control opens the internal valve; pushing the handle closes the valve. There are three notches on the primary control that give a travel of 4, 5, or 6-inch (102, 127, or 152 mm) depending upon the travel required by the valve’s operating lever.

tYpe p650

Included with each Type P650 primary control is a 20 feet (6,1 m) cable, Type P134 fusible links, a return spring and mounting hardware. If just the primary cable control is needed, order Type P651, which is available without any of the other accessories.

primary cable control Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)

P650 Cable control assembly for 2 and 3-inch disk valves, 20 feet (6,1 m) 5 (2,27)

P651 Primary cable control only 3 (1,36)

ordering guide



188


tYpe p315

types p314 cable assembly and p315 auxiliary Remote Release

introduction

Type P314 – This cable assembly is used as an attachment from the Type C404-32 operating lever to the primary cable control. The assembly includes a 40 feet (12,2 m) cable, a special bushing with a fusible element and clamp. The bushing fits in the valve-operating lever and has a built-in fusible element that will melt if exposed to fire, allowing the Type C404-32 to close. The cable connects to the bushing and the clamp permits the other end of the cable to be attached to the fusible link (not furnished) at the primary cable control.

Internal Valve Accessories Ordering InformationInTernAl VAlVe sIze,

IncHes (dn) prImAry cAble cOnTrOl AuxIlIAry remOTe releAse cAble Assembly lATcH/releAse mecHAnIsm

1-1/4, 2, and 3 (32, 50, and 80)(Threaded or Flanged) Type P650 or P651(1) Type P163A or P164A Included with Type P650 Types P341, P342 (Type C407-10),

P340 (C400 Series)

4 (100) Flanged Use Allegheny orWheaten Control Type P315 Type P314 Type P313(2)

1. Type P651 is a primary control only, no accessories. 2. Use with Type P315 remote release mechanism.

ordering guide



Type P315 – On manually actuated 4-inch (DN 100) valves (Type C404M32), Type P315 remote handle release can be used to close the internal valve from a remote location. Cable linkage [30 feet (9,1 m)] and mounting hardware are included.

189


types p312, p389, and p326 series pneumatic actuatorsintroduction

All Fisher® internal valves can be ordered with an air cylinder that permits the valve to be opened and closed from a remote location. When air pressure is applied to the cylinder, it moves the cylinder’s rod and internal valve operating lever to the open position. Upon loss of air pressure, the valve’s operating lever returns to the closed position. Besides air pressure, nitrogen or carbon dioxide can also be used to pressure the cylinder.

Use of an air cylinder type of actuator permits the opening and closing of the internal valve to be tied into the air brake of the transport or bobtail. Air cylinders can also provide a convenient way to remotely operate a number of internal valves on stationary storage tanks at bulk plants.

Type P389 (1-1/4-Inch Size) – This cylinder can only be used with the Type C407-10 valve. All necessary hardware for installing the cylinder is included.

tYpe p389

Type P326-5 – For Type C403-24 double flanged valves.

Type P326-6 – for Type C401, C407, C421 and C427 valves (2 and 3-inch sizes).

Type 326-7 – for Type C404-24 and C413-24 single flanged valves.

The P326 kits feature a spring return design which eliminates the need for an air return. The “rolled” cylinder diaphragm has a special seal that prevents air leakage and minimizes friction. A bellows covers the cylinder rod to prevent build-up of foreign material around the rod, and a filter in the cylinder vent keeps out dust.

Type P312 (4-Inch Size) – Also available factory installed (C404A32), the cylinder attaches directly to the valve after removal of the cable-operating lever. Included in each assembly is an operating lever and mounting hardware.

pneumatic cylinder Actuators Ordering InformationInTernAl VAlVe Type numbers

pneumATIc cylInder AcTuATOr Type number

mAxImum InleT pressure TO cylInder,psIG (bar)

mAxImum OperATInG pressure TOAcTIVATe InTernAl VAlVe, psIG (bar)

C403-24 P326-5 125 (8,6) 20 (1,4)

C407, C421 and C427 P326-6 125 (8,6) 20 (1,4)

C404-24 P326-7 125 (8,6) 20 (1,4)

C404-32 P312 250 (17,2) 60 (4,1)

C407-10 P389 250 (17,2) 60 (4,1)

tYpe p326

tYpe p312

ordering guide



190


types p327c and p327d air cylinders introduction

Type P327C—Opening and closing of Snappy Joe® ESVs from a remote location can be done by using Type P327C air cylinder. Depending upon valve inlet pressure, a minimum supply pressure of 30 to 70 psig (2,07 to 4,83 bar) to the cylinder opens the valve. Air, nitrogen, or CO2 can be used for the cylinder supply source. Maximum inlet pressure to the cylinder is 125 psig (8,6 bar). Operating temperature range is -65° to 225°F (-54° to 107°C).

Upon loss of pressure, the valve closed, assisted by the spring in the pneumatic cylinder. All necessary installation hardware for Type P327C is furnished.

Type P327D—Remote pneumatic closure is available with Type P327D release. Depending upon valve inlet pressure, a minimum supply pressure of 30 to 70 psig (2,07 to 4,83 bar) on the Type P327D allows the valve to be latched in the open position with manual closure possible at the valve. Loss of supply pressure to the cylinder permits the ESV to close. Air, nitrogen, or CO2 can be used for the cylinder supply source. Maximum inlet pressure to the cylinder is 125 psig (8,6 bar). Operating temperature range is -40° to 212°F (-40°C to 100°C).

tYpe n550 WitH tYpe p327c

tYpe n550 WitH tYpe p327d

ordering guide



Air cylinder Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)

P327C Air cylinder kit for N550 (open and close)1 (0,5)

P327D Air cylinder kit for N550 (close only)

191


introduction

Type P539 pneumatic actuator permits opening and closing Fisher® N550 Series Snappy Joe® emergency shutoff valves (ESVs) both at the valve with the use of a pneumatic 4-way valve and from a remote location. The actuator opens the valve when pressure is applied.

Upon loss of pressure, the N550 Series closes, assisted by the spring in the pneumatic actuator.

internal Valve end connection size and style

2 and 3-inch threaded NPT

Actuator pressure limits

Minimum: 20 psig (1,38 bar)Maximum: 100 psig (6,90 bar)Recommended Operating Pressure: 20 to 25 psig (1,38 to 1,72 bar)

Return mechanism

Internal Spring, no air

temperature capabilities

-20° to 150°F (-29° to 66°C)

melt point

212°F (100°C)

approximate Weight

4.8 pounds (2,198 kg)

additional technical data

For more technical information, contact your local LP-Gas and Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp

Figure 1. Type P539 Pneumatic Actuator shown on an N550 Series Emergency Shutoff Valvefeatures

• Provide a Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder

Table 1. construction materials

mOunTInG brAckeT flAT wAsHer And lOck sprInG wAsHer spAcer leVer pusH In fITTInG

304 Stainless steel Carbon plated steel Aluminum 410/416 Stainless steel Brass

type p539 pneumatic actuator

P1136

Figure 2. Dimensions

1/4-incH npt212°f (100°f)fuse plug

1/4-incH mnpt

incHes(mm)

GE31238_C

4.49(114)

5.12(130)

3.71(94,2)

0.79(20,1)

ordering guide

To order this product, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp

192


introduction

All Fisher® 2 and 3-inch threaded NPT, 3-inch (DN 80) single and double flanged internal valves can be fitted with an air operated actuator that can be used to open and close the internal valves at the valve or from a remote location. A 3-way valve installed at the valve or at the desired remote location allows air or nitrogen pressure to be applied to the actuator. The pressure supply moves the actuator rod and the internal valve’s operating lever, opening the valve. Upon loss of air pressure, the valve’s operating lever immediately returns to the closed position.

Type 613—For Types C404-24 and C414-24 single flanged valves.

Type P623—For Types C403-24 and C413-24 double flanged valves.

Type P639—For Types C407, C421, and C427 valves (2 and 3-inch threaded NPT sizes).


2 and 3-inch (DN 50 and 80) threaded NPT, single, or double flanged



Return mechanism

Spring only, no air

thermal Release

1/4-inch threaded NPT fuse plug installed in center port of actuator housing


-20° to 150°F (-29° to 66°C)

melt point

212°F (100°C)

approximate Weight

5.6 pounds (2,552 kg)


For more technical information, contact your local LP-Gas Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp

Figure 1. Type P613 Pneumatic Actuator

types p613, p623, and p639 pneumatic actuators

features

• Provide a Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder

Table 1. construction materialsmOunTInG brAckeT lOck sprInG wAsHer cOTTer pIn leVer pusH In fITTInG

304 Stainless steel Zinc plated steel Steel Ductile iron Brass



P1131

P1132

P1134

193


types p613, p623, and p639 pneumatic actuators

ordering guide


incHes(mm)

GE29523

GE31237

3.15(80,0)

5.79(147)


1/4 (6,35)tuBing

1/4-incH mnpt

p613 pneumatic actuatoR

5.24(133)

5.63(143)

5.63(143)

1/4 (6,35)tuBing

1/4-incH mnpt



0.79(20,1)


GE31236

5.63(143)

3.15(80)

5.63(143)

1/4 (6,35)tuBing

1/4-incH mnpt


0.79(20,1)

To order, specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:


194


type p614 pneumatic actuatorintroduction

Type P614 can only be used for Types C404-32 and C804-32 single flanged valves. Fisher® 4-inch (DN 80) single flanged internal valves can be fitted with an air operated actuator that can be used to open and close the internal valves at the valve or from a remote location. A 3-way valve installed at the valve or at the desired remote location allows air or nitrogen pressure to be applied to the actuator. The pressure supply moves the actuator rod and the internal valve’s operating lever, opening the valve. Upon loss of air pressure, the valve’s operating lever immediately returns to the closed position.


4-inch (DN 100) single Flanged



Return mechanism

Spring only, no air

thermal Release

1/4-inch threaded NPT fuse plug installed in center port of actuator housing


-20° to 150°F (-29° to 66°C)

melt point

212°F (100°C)

approximate Weight

9.6 pounds (4,344 kg)


For more technical information, contact your local LP-Gas and Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp

features

• Provide Aa Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder


Table 1. construction materialsmOunTInG brAckeT lOck sprInG wAsHer rOll pIn leVer pusH In fITTInG

304 Stainless steel Carbon plated steel Carbon plated steel Ductile iron Brass

ordering guide


incHes(mm)

GE31240

6.02(153)

3.15(80)

6.26(159)

1/4 (6,35)tuBing

1/4-incH mnpt


0.79(20,1)


195


type p631 pneumatic actuator

introduction

Type P631 Pneumatic Actuator can only be used with C407-10 Series valves, it permits the valve to be opened and closed from a remote location. When air pressure is applied to the cylinder, it moves the cylinder’s rod and internal valve operating lever to the open position. Upon loss of air pressure, the valve’s operating lever returns to the closed position.


1-1/4-inch threaded NPT




-20° to 150°F (-29° to 66°C)

approximate Weight

4.1 pounds (1,842 kg)


For more technical information, contact your local LP-Gas Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp

features

• Can only be used for C407-10 Series Internal Valves• Provide a Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder


Table 1. construction materialsbrAckeT, bAse,

And cOVerHex HeAd screw,

rOll pInlOck sprInG wAsHer,

JAm Hex nuT leVer And rOd sprInG seAT sprInG cOTTer pIn

304 Stainless steel Carbon plated steel 18-8 Stainless steel 410/416 Stainless steel Aluminum 302 Stainless steel Stainless steel

P1133

ordering guide


2.31(58,7)

5.0(127)

4.02(102)

GE30288

incHes(mm)


196


introduction

M3162 Series Clamp Hose Couplings, for use on LP-Gas or Anhydrous ammonia (NH3), are designed to be compact yet rugged for long, dependable service. A small boss on the clamp portion of the coupling keeps the bolt from turning when installing, making installation much easier. Each ductile iron unit receives a coat of electrodeposition paint. Larger size clamp hose couplings can be furnished with a swivel nut female ACME outlet that reduces weight and space.

m3162 series clamp Hose couplings

clamp and coupling Ordering Information

cOuplInG sTyle sIze, IncHes HOse I.d. , IncHes (mm) ApprOxImATe HOse O.d., IncHes (mm) Type number(1)

Clamp Type, Standard Outlet

1/2 MNPT 1/2 (12,7) 15/16 (23,8) M3162-08

3/4 MNPT 3/4 (19,1) 1-1/4 (31,8) M3162-12

1 MNPT 1 (25,4) 1-1/2 (38,1) M3162-16

1-1/4 MNPT 1-1/4 (31,8) 2 (50,8) M3162-20

1-1/2 MNPT 1-1/2 (18,1) 2-1/4 (23,8) M3162-24

2 MNPT 2 (50,8) 2-3/4 (57,2) M3162-32

3 MNPT 3 (76,2) 3-3/4 (95,3) M3162-48

Clamp Type,Swivel Nut Outlet

1-3/4 Female ACME 3/4 (19,1) 1-1/4 (31,8) M3162-12S(2)

3-1/4 Female ACME 2 (50,8) 2-3/4 (57,2)M3162-32S(2)

M3162-32B(3)

4-1/4 Female ACME 3 (76,2) 3-3/4 (95,3)M3162-48S(2)

M3162-48B(3)

1. Maximum allowable working pressure 350 psig (24,1 bar).2. Has a steel swivel nut with ductile iron nipple.3. Has a brass swivel nut with ductile iron nipple. DO NOT USE WITH ANDHYROUS AMMONIA (NH3).

tYpe m3162-08

ordering guide



197


type p120B spanner Wrenchintroduction

Used to tighten and loosen large female ACME caps and couplings in the 2-1/4, 3-1/4, and 4-1/4-inch ACME thread sizes.

tYpe p120B

spanner wrench Ordering Information

Type number OVerAll lenGTH,IncHes (mm)

cOnsTrucTIOn mATerIAl

ApprOxImATe weIGHT,pOund (kg)

P120B 18 (457) Aluminium 1 (0,45)

ordering guide

To order, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:


introduction

Types P206, P297, and P298 protective caps are used to keep moisture and foreign materials from entering the valves. These units are mounted the outside the protective hood on the tank.

types p206, p297, and p298 protective caps for Relief Valves

relief protective cap Ordering InformationVAlVe Type prOTecTIVe cAp Type

H110

P206

H135

H160

H148

H173

H123

H120

H124

H144

H174

H722 P297

H732 P298

tYpe p298

198


introduction

Ring and chain assemblies prevent loss of caps and seals. Available for 1-1/4-inch ACME caps or dust seals.

ring and chain Assembly Ordering Information

Type number fOr cAp Or dusT seAlsIze, IncHes fOr fIsHer® brAnd Type

P147 1-1/4 ACME M108 M178

P147(1)

1-3/4 ACMEM109 or M219 - - - -

P148(2) M109 M179

P1482-1/4 ACME

- - - - M180

P167 M431 or M432 - - - -

P1833-1/4 ACME

- - - - M181

P167 M441 or M443 - - - -

P167 4-1/4 ACME M605-34, M625-34M, and M535-34 - - - -

1. Type P147 fits 3/4-inch (19,1 mm) pipe size. 2. Type P148 fits 1-1/4-inch (31,8 mm) pipe size.

p147 oR p148 p167

types p147, p148, and p167 Ring and chain assemblies

ordering guide



Documents

LP-Gas EquiPmEnt and accEssoriEs - Emerson · Your local LP-Gas Equipment Distributor can assist you in selecting the proper regulators and ... Male ACMe Adaptor Female ACMe Filler