Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011 1
Installation InstructionsIQL16/xxx, /AHU
LONMARK® Terminal Unit Controllers
Important: Retain these instructions
3 Installation - Mounting
CONTENTS
1 Unpacking................................................12 Storage ....................................................1
1 Unpacking
IQL16/xxx, /AHU Installation Instructions TG200453
H O2
+50 °C(122 °F)
0-10 °C(14 °F)
90 %RH
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
129
mm
(5.0
8”)
75 mm (3”)
205 mm (8.07”)
Dimensions
63 mm (2.48”)
1
3 Installation - Mounting .............................14 Installation-Configuration ......................65 Disposal .................................................12
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
ba
Requirements2
Note that this product may involve LONWORKS ® system integration as referred to in section 4 step 4: this procedure should only be performed by an installer with LONWORKS engineering expertise.
2 StorageIt is recommended that the instal lat ion should comply with the local electrical safety installation practices (e.g. HSE Memorandum of Guidance on Electricity at Work Regulations
1989, USA National Electric Code).
These instructions shall be used by trained service personnel onlyIftheequipmentisusedinamannernotspecifiedbytheseinstructions,theprotectionprovidedbytheequipment may be impaired.
2 IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011
IQL16/xxx, /AHU Installation Instructions
3 Requirements (continued)
3 Installation - Mounting (continued)
4 holes� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
∅ 6 mm(0.24”)
Mounting
114
mm
(4
.49”
)
3
Lift Hinged Cover4
189 mm (7.44”)
LAN
NID
Strategy
::
::
:
O/S
Serial No
1 1 +
L
LAN
NID
Strategy
::
::
:
O/S
Serial No
1 1 +
L
LAN
NID
Strategy
::
::
:
O/S
Serial No
1 1 +
L
a
b c
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
either surface mount
or DIN rail mount
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
a b c d
WARNING: Failure to use a screwdriver to open the cover will cause damage to the unit.
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
c� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
dH O
2
+45 °C(113 °F)
0
0 °C(32 °F)
90 %RH
1 3+
LLAN
NID
Strategy
: : : : :
O/S
Serial No
230 Vac
~24V COM
21 22 23 24 25 26 27 281 2 3
COM
1 2 3 54 6 7
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 2 3 4 5
~24V
LON
29 30 31 32
LONOK
SRVPIN
C
24 Vac
e
Protection: IP20, NEMA 1
Altitude: <2000 m
f
g
Avoid locations where corrosive fumes or explosive vapours are present. Avoid electrical noise interference.
This unit must be installed in an enclosure conforming to EN61010-1
1 3 +
LLAN
NID
Strategy
: : : : :
O/S
Serial No
230 Vac
~24V COM
21 22 23 24 25 26 27 281 2 3
COM
1 2 3 54 6 7
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 2 3 4 5
~24V
LON
29 30 31 32
LONOK
SRVPIN
C
13+
LLAN
NID
Strategy
: : : : :
O/S
Serial No
230 Vac
~24VCOM
21 22 23 24 25 26 27 28 1 2 3
COM
1235 467
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
12345
~24V
LON
29 30 31 32
LONOK
SRVPIN
C
13
+LLA
N
NID
Stra
tegy
: : : : :
O/S
Se
rial N
o
23
0 V
ac
~ 24
VC
OM
21
22
23
24
25
26
27
28
1 2
3
CO
M
12
35
46
7
6 7
8 9
10 1
1 1
2 1
3 1
4 1
5 1
6 1
7 1
8 1
9 2
0
12
34
5
~ 24
V
LO
N
29
30
31
32
LO
NO
K
SR
VP
IN
C
13
+ LLA
N
NID
Str
ate
gy
: : : : :
O/S
Se
ria
l N
o
23
0 V
ac
~24
VC
OM
21
2
2
23
2
4
25
2
6
27
2
81
2
3
CO
M
12
35
46
7
6 7
8
9
1
0 11 1
2 1
3 1
4 1
5 1
6 1
7 1
8 19 20
12
34
5
~24
V
LO
N
29
3
0
3
1
32
LO
NO
K
SR
VP
IN
C
DIN rail end stop!
IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011 3
Installation Instructions IQL16/xxx, /AHU
Connect Power5
DO NOT APPLY POWER
�
�
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
3 Installation - Mounting (continued)
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
6
� � � � � � � � � �
� � � � � � � � � �
� � � � � � � � � �
LON - FTT (free topology)
Star topology Bus topology Loop topology*Terminate LONWORKS bus at one end only
polarity independent
Connect LONWORKS LON
29 30 31 32
L W
network
ON ORKS L W
network
ON ORKS
** *
Do not allow wires to cross on a loop
100 � F, 50 V min
100 � F, 50 V min
Terminatore.g.LONTERMINATOR
LonASCN LonB LonASCN LonB
LINC
A
IQLROUTER
B
IQL
x y
A
IQLROUTER
B
zw
IQL
x y zw
T
T T
4 5 6 7 8 9 10 11
4 5 6 7 8 9 10 11
L N E
230 Vac
1 2 3
Clean earths, grounds, consisting of short (<300 mm, 12”) stranded copper wire (>=1.5 mm2, 16 AWG) to a substantial earthed, grounded, metal part (e.g. cable tray) are recommended
Terminal size 0.5 to 2.5 mm2
(14 to 20 AWG)
24 Vac
1 2 3
24Vac
Earth, ground, 24 Vac supply neutral at transformer
/24VAC option /230 optionIQL consumption
<= 12.1 VA (2.5 VA + power to 24 Vac auxiliary supply and triac outputs)
IQL consumption<= 13 VA (3 VA + power
to 24 Vac auxiliary supply and triac outputs)
continued over page
Maximum 64 nodes per LONWORKS segmentMaximum 40 IQLs (and LONCs) per virtual Lan
Recommend terminate at LINC or Router.e.g. use IQLRouter integral terminators
A switch or circuit breaker must be included in the supply to the unit and be in close proximity to it, and must be clearly marked as the disconnecting device for the unit.
This unit is protected to safety class 2. The earth on this unit is NOT a
protective earth, but it is essential that anearthisfittedforfunctionalreasons.
4 IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011
IQL16/xxx, /AHU Installation Instructions
SupplyFan
InletDamper Extract
Fan
1 2 3
6 7 8 9 10 11 12 13 14
Connect Inputs and Outputs7If non standard strategy, follow special installation instructions and jump to step 13
Non-standard Strategy Installation Instructions
6
3 Installation - Mounting (continued)
Connect LONWORKS (continued)
If used with LPT-10 (powered bus), cable lengths differ - see “Link Power Transceiver User’s Guide (078-0105-01C)”.
LINC LINC
IQ System Outstations IQ System
Outstation
L M
Device
ON ARK
IQL
L WON ORKS bus
Normal IQ System current loop Lan cable is not recommendedDo not use screened cable
Terminal size 0.5 to 2.5 mm2 (14 to 20 AWG)
Cable Max bus length Max node to nodeBelden 85102 500 m (545 yds) 500 m (545 yds)TrendTP/1/0/16/HF/200 (Belden 8471)
500 m (545 yds) 400 m (430 yds)
UL Level IV, 22 AWG 500 m (545 yds) 400 m (430 yds)
JY(St) Y2 x 2 x 0.8 500 m (545 yds) 320 m (350 yds)
TIA5268A Cat. 5, 24 AWG 450 m (430 yds) 250 m (270 yds)
Connect Inputs8� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
Connect Relay Outputs9
Trip -e.g. Filter Dirty
FrostThermostat
LocalSpace
TemperatureSensor
Local SetpointAdjust
Potentiometer
DuctTemperature
Sensor
COM
21 22 23 24 25 26 27 28
COM
1 2 3 4 5
C
�
12 3
TB/TS /K
COM
21 22 23 24 25 26 27 28
COM
1 2 3 4 5
C
Sensors TB/TS, TB/TS/K recommended; wire as shown below.
alarm trip
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
WARNING: The wires may be connected to hazardous voltages. Disconnect power before attempting any wiring.
For IQL16/24VAC, UL rating applies up to 30 Vterminal size 0.5 to 2.5 mm2 (14 to 20 AWG) - Cu only
Arc Suppression TG200208
t e r m i n a l size 0.5 to 2.5 mm2 (14 to 20 AWG) - Cu only
Note t ha t t e rm ina l
types COM, � �� �
and C should not be connected together.
5A maximum at 240 V resistive or inductive (cos Ø>=0.4)5A at 30 Vdc (resistive), 2A at 24 Vdc (inductive, T<=30 mS)
Note that to meet safety requirements, for the 3 relays (OUT1 to OUT3), those being used must all be switching either low voltage or mains and not a mixture of voltages. If switching mains, they must all switch the same phase and polarity.
IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011 5
Installation Instructions IQL16/xxx, /AHU
14 Close Enclosure
15 Cleaning & Maintenance
There are no serviceable parts inside the unit. Cleaning of the unit
should be carried out in order to avoid buildup of dust or other contaminents. Disconnect power before carrying out any cleaning. Clean surfaces with a cloth moistened with water.
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
Load
24 Vac
4 5
Ra
ise
Recirc/FAMixing
Damper
Co
mm
on
Lo
we
r
~24V 10V 0V 10V
AO
54 6 7
15 16 17 18 19 20
3 Installation - Mounting (continued)
Close Hinged Cover13
LAN
NID
Strategy
::
::
:
O/S
Serial No
1 1 +
L
a
b
LAN
NID
Strategy
::
::
:
O/S
Serial No
1 1 +
L
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
Connect Heat/Cool Outputs10
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
He
at
Va
lve
Co
ol V
alv
e
~24V 10V 0V 10V
AO
54 6 7
15 16 17 18 19 20
0 to 10 Vdc, 10 mA max.; shares 280 mA with mixing damper output and auxiliary supply
Above 40 °C (104 °F) the maximum current available is 180 mA
Note that terminal types
COM, � �� �
and C should not be connected together.
Connect Mixing Damper Output11
24 Vac, 280 mA max. shared with heat/cool output and auxiliary supply
Above 40 °C (104 °F) the maximum current available is 180 mA
Connect 24 Vac Auxiliary Supply12
24 Vac, 280 mA max. shared with heat/cool and mixing damper outputs
Above 40 °C (104 °F) the maximum current available is 180 mA
terminal size 0.5 to 2.5 mm2 (14 to 20 AWG) - Cu only
terminal size 0.5 to 2.5 mm2 (14 to 20 AWG) - Cu only
terminal size 0.5 to 2.5 mm2 (14 to 20 AWG) - Cu only
Note that terminal types
COM, � �� �
and C should not be connected together.
1 3+
LLAN
NID
Strategy
: : : : :
O/S
Serial No
230 Vac
~24V COM
21 22 23 24 25 26 27 281 2 3
COM
1 2 3 54 6 7
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1 2 3 4 5
~24V
LON
29 30 31 32
LONOK
SRVPIN
C24 Vac
6 IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011
IQL16/xxx, /AHU Installation Instructions
4 Installation - Configuration
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
�
�
LINC LINC
IQ System Outstations IQ System
Outstation
L M
Device
ON ARK
IQL
L WON ORKS bus
(Check LONWORKS, LINCs)
LON OK (green)
Flashes every 24 s, ON after 1½ mins
Switch On2
Check IQL/LINC on LONWORKS Bus3
Flashes every 1 s (Deaf IQL. Check LONWORKS)
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
See LONWORKS network management tool manual. See IQ System LONWORKS Produc ts Eng ineer ing Manua l (TE200292). LONWORKS System Integrator must have LONWORKS engineering expertise.
a). When installing IQL in LONWORKS tool, press service button when requested.
b). The IQL network image can be obtained from www.lonmark.org, or from www.pnet.trend-controls.com.
c). Set up bindings if required (bind network variables between IQL and LONMARK devices).
IQL16 Data Sheet TA200451 for LONWORKS network variables (NVs)
Install using LONWORKS Network Managment Tool4 If a binding IQLs to LONMARK devicesor b LINCs version <3.23 straddle routeror c otherdeviceshaveaddressconflictswithIQSystemdevicesor d IQLROUTERs used on installed system
SRV PINservice button
LINC
L W
network
ON ORKS
IQL
LONMARK
device
If one IQ System LONWORKS device is installed, all must be installed.
Tear off Label Strip1
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
� � � � �� � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � �
� � � � � � � � � � �� �
� � �
� � � �� � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � �
� � � � � � � � � � � � � � � �
� � � �� �
� � � � �
�
XTEND -4000070963Xtream
LAN
MAC Addr 00.10.70.00.UD.BB
O/S
S/No:
IP Addr Location
MAC Addr 00.10.70.00.UD.BB
S/No:Q3B____X73010003
IP Addr
� � �
� � � � � � � � �� � � � � � � � � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � �� � �� � �
‘locate’
IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011 7
Installation Instructions IQL16/xxx, /AHU
4 Installation - Configuration (continued)
Note that a PIN may be required to make changes. If the PIN has been forgotten the users should contact their supplier (installers contact Technical Support)
quoting the generator number and neuron id (both from Address module) whereupon a default PIN will be supplied. This will only work for three attempts at entering the PIN. After the default PIN is entered a new PIN should be set up and remembered.
1 1 +
L
LAN
NID
Strategy
: : : : :
O/S
Serial No
230 Vac
~24V COM
15 16 17 18 191 2 3
24 Vac
LON
20 21 22 23
1 32 4 5
4 5 6 7 8 9 10 11 12 13 14
1 2 3
~24V
LONOK
SRVPIN
C
L WON ORKS
network
LCI
IQL
Connect software tool for text commissioning5if required
Exercise I/O6If IqlTool2 available
IqlTool2 Manual TE200185
Use IqlTool2 to monitor inputs and exercise outputs
Test input/output functionality7
Non-standard Strategy Installation Instructions
If non standard strategy follow special installation instructions and jump to step 12.
IqlTool2 ManualTE200185
LCI Installation Instructions TG200429SET Manual TE200147
IqlTool2 (SET)IqlTool2 runs within SETV5 (or later)
RS232 cable supplied with LCI
1 1 +
L
LAN
NID
Strategy
: : : : :
O/S
Serial No
230 Vac
~24V COM
15 16 17 18 191 2 3
24 Vac
LON
20 21 22 23
1 32 4 5
4 5 6 7 8 9 10 11 12 13 14
1 2 3
~24V
LONOK
SRVPIN
C
L WON ORKS
network
LCI
IQL
IqlTool2(SET)
Note that IqlTool2 may also be used for mapping the LONWORKS segment, resolving duplicate addresses on LONWORKS network, identification via service button, associating with SDU-LON (for other uses see later)
LONWORKS adapter cable supplied with LCI
8 IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011
IQL16/xxx, /AHU Installation Instructions
�
�
�
�
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
S
S
�
Check Strategy, Sensors/Dampers/Fans/Heat, Cool Valves
IN1
OUT1 � � � � � �� � � �
� � � � �� � � �
� � � � � �� � � �
� � � � �� � � �
Free cooling if outside air temperature (K7) < S1
�� � �
�� � �
S
S
�
IN3
inlet OUT2inlet extract
spaceduct
OUT3
OUT4,5coolOUT7
heatOUT6
During occupation (default)
8
�
�
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
9
OUT1� � � � � �� � � �
� � � � �� � � �
�� � ��� � �
inlet OUT2inlet extract
OUT3
OUT4,5coolOUT7
heatOUT6
Check Frost Thermostat if fitted
�IN5
fan off fan off
if W3=0, Frost Stat enabled (default)
Note that if Frost Thermostat is not fitted, it must be disabled for fans to run (W3=1).
4 Installation - Configuration (continued)
IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011 9
Installation Instructions IQL16/xxx, /AHU
Check Operation - Local SP Adjust10
IN2
�
�
OUT1 � � � � � �� � � �
� � � � �� � � �
�� � ��� � �
inlet OUT2inlet extract
OUT3
OUT4,5coolOUT7
heatOUT6
Wait 6 secs at each end to calibrate potentiometer
� �
�� � �
� � �
� � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � �
� � � � � � � � �
During occupation (default)
4 Installation - Configuration (continued)
Set up Strategy Parameters 11if required
Use IqlTool2 (see step 5) and text communications
For standard strategies use table below, else refer to non-standard strategy installation instructions
Note that any changes to the strategy parameters should immediately be followed by a write to the address module, [text comms command, R(z=O), recommended], to commit changes to flash memory.Note that D4 full scale drive time should not be greater than 262s.
Parameter Label Function DefaultK1(V) Remote Setpoint Base setpoint can be adjusted remotely 20 °CK2(V) RemoteSpace Temp Used if bound to LONWORKS sensor, or if space sensor disconnected 20 °CK3(V) OCC Deadbnd Deadband around setpoint during Occ 1 °C
K5(V) NOCC Deadbnd Deadband around setpoint during Nocc 12 °CK6(V) Remote Occ Sets state 0=Occ, 1=Nocc 0=OccupiedK7(V) Remote OAT. Outside Air Temp for free cooling 10 °CK8(V) Remote SP Offset SP offset used if bound to a LONWORKS sensor or SP adjust has error 0 °C
K9(V) Rem Supply Temp Used if bound to LONWORKS sensor, or if duct sensor disconnected 20 °CK10(V) Duct Frost Pro If duct temp falls below this, frost protection is required 5 °C
K14(V) Min Nocc Run Min inlet damper open on time during Nocc 1200 secsK15(V) Offset range DefinesrangeofLocalSPadjustpot. 2 °C
W2(S) Free Clg Enable Enables free cooling if Remote OAT < Space Temp 0=disable free coolW3(S) Frst St Disable Disablesfrostactionifsetto1(e.g.thermostatnotfitted) 0=enable frost action
W8(S) Remote Shutdown Shuts off fans, closes inlet damper, closes valves, mixing damper goes to full recirculation 0=no shutdown
L1(G) Heat Loop Gain 20L1(I) Heat Loop Integral 0 mins
L2(G) Cool Loop Gain -20
L2(I) Cool Loop Integral 0 mins
10 IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011
IQL16/xxx, /AHU Installation Instructions
4 Installation - Configuration (continued)
Note 1: IqlTool2 facilitates setting of these parameters across the LONWORKS segmentNote 2: Changing any of these parameters results in a controller reset (clears down time and and sensor logs)Note 3: Any changes to these parameters should immediately be followed by a write to the address module, [text comms command, R(z=O), recommended], to commit changes to flash memory.Note 4: IqlTool2 facilitates setting to timekeeper (sets up timemaster Lan and changes own address to 11)Note 5: Message code can only be changed by text comms if ‘lonworks managed’ (read only) is set to No.Note 6: If PIN is forgotten see note in step 5
Using IqlTool2 (see step 5) and text communications
Set up System Core Firmware Module Parametersif required - see conditions
12
Parameter Setting Function Condition NoteR(..address L - own address device address of IQL if required to rearrange
Lans, address1, 2, 4
N - own LaN Lan number of IQL if required to rearrange Lans, address
1, 2
D-identifier identifierattributeofIQL For alarm ident, text comms, IC comms
1
F - attribute 2 text comms attributes For text comms, IC comms 1G - attribute 3 1A - own Lan alarm address
address and Lan of own Lan alarm target
to report Lan alarms to a supervisor
1
R - Own Lan alarm Lan 1E - Internetwork alarm address
address and Lan of Internetwork alarm target
to report internetwork alarms to a supervisor (only for lowest addressed IQ System device on Lan)
1
T - Internetwork alarm Lan 1
r - LONWORKS retry time See IQ System LONWORKS Products Engineering Manual for details
2i - LONWORKS interpacket delay
2
a - LONWORKS service class
2
b - router Buffer size buffer size (bytes) Default = 146
specifiessmallestrouterbuffer on system
If routers separate IQLs/LINCs/LONCs and have buffer size smaller that 146 bytes - set to smallest buffer size. (minimum = 66)
2
m - LONWORKS Message code
code number. Default = 64
Code used by IQLs/LINCs/LONCs, all LINCs/LONCs must use same code
If message code being used by other users - must be exclusive to IQ System
2, 5
g - generator number TofindPINiflost (read only)e - Neuron Chip id unique
identifierforNeuron®
TofindPINiflost;toidentify LONWORKS node
(read only)
T(..Time H - Hours Current time To synchronise time for alarms and loggingN - Minutes
D - Day of month Current date To synchronise date for alarms and logging
3M - Month 3Y - Year 3l - Lan of system timemaster
IQL timekeeper gets time sync from IQ at address 11 on this Lan
IQL will be timekeeper If this ‘l’ parameter is non-zero and own address = 11
3, 4
U1(..User P - PIN PIN number in IQ To protect from unauthorised changes
3, 6
l -level authority level of PIN No protection if zero 3
IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011 11
Installation Instructions IQL16/xxx, /AHU
4 Installation - Configuration (continued)
Set up Lan System 13 LINCInstallation Instructions TG103062
L WON ORKSnetwork
IQL1 1 +
L
LAN
NID
Strategy
: : : : :
O/S
Serial No
230 Vac
~24V COM
15 16 17 18 191 2 3
24 Vac
LON
20 21 22 23
1 32 4 5
4 5 6 7 8 9 10 11 12 13 14
1 2 3
~24V
LONOK
SRVPIN
C
LINC
IQ
Check Lan
if required
IQ System LONWORKS Products Engineering Manual TE200292
Use SET and terse text communications
SET
IQL
IC Comms
LINC
IQ
L W networkON ORKS
Nx
K1
W1
S1
K2
K8
W7
W8
I1
I8
S8
Nx
LCI
IC Comms Module Nx(.. - (x=1 to y; y=4 for standard strategies)
Set up IC Comms from IQL if required
14
Parameter Function
A - Remote device address
If zero, ‘global to’ comms. Ifnon-zerospecifiestarget device address for ‘data to’ comms
B - Attribute
For ‘global to’ comms only, attribute of target IQ, references attribute in address module (0 ‘no attribute’, - all IQs onLan,1‘identifier’,2‘attribute 2’, 3 ‘attribute 3’)
N - Remote LanTarget IQ Lan number; if Lan zero, address zero, specifiesglobalglobal
I - Interval Interval between sending (minutes)
S-Significantchange
Amount analogue must change before sending
M - Source item string
Item and parameter being sent (e.g. S1(V))
E - Destination module number
No. of destination module receiving IC comms
T - Destination typeType of destn module receiving comms (e.g. W,K)
Use IqlTool2 (see step 5) and text communications
12 IQL16/xxx, /AHU Installation Instructions TG200453 Issue 5, 21-Nov-2011
IQL16/xxx, /AHU Installation Instructions
Please send any comments about this or any other Trend technical publication to [email protected]
© 2011 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.
Trend Control Systems LimitedAlberyHouse,SpringfieldRoad,Horsham,WestSussex,RH122PQ,UK.Tel:+44(0)1403211888Fax:+44(0)1403241608www.trendcontrols.comTrend Control System USA6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel:(425) 869-3900 Fax:(425) 869-8445 www.trend-americas.com
WEEE Directive :At the end of their useful life the packaging and product should be disposed of by a suitable recycling centre.Do not dispose of with normal household waste.Do not burn.
IQL
IC Comms
LINC
IQ
L W networkON ORKS
Nx
K1
W1
S1
K2
K8
W7
W8
I1
I8
S8
Nx
IC Comms ‘direction’ in IQ must be: Global To, Min, Max, Sum, or Average (directions 2 to 6)
see IQConfigurationManual 90-1533
Set up IC Comms from IQif required
15
LINC
IQ
Terse Text Comms
K1
W1
S1
K2
K8
W7
W8
I1
I8
S8
L W networkON ORKS
IQL
Set up Communications from Supervisor
if required
16
Note that any changes to the strategy parameters should immediately be followed by a write to the address module, [text comms command, R(z=0), recommended], to commit changes to flash memory.
4 Installation - Configuration (continued)
e.g. 963 (drag and drop values)
Note that standard strategy pages are available for 963 from Partnernet
Use SET and terse text communications
5 Disposal