Logopress3 News 2016 SP0-x

8/15/2019 Logopress3 News 2016 SP0-x

1/21

What is new in Logopress3 2016


2/21

Logopress3 News 2016 SP0.x 2 / 21

What's new?

Version 2016 Service Pack 0.3 (1st of March 2016) (64-bit only)certified for:

SOLIDWORKS 2016 SP2SOLIDWORKS 2015 SP5 + HotFix 920938SOLIDWORKS 2014 SP5

What i s f ixed in thi s version? (Page 15)

Version 2016 Service Pack 0(4th of January 2016) (64-bit only) certified for:

SOLIDWORKS 2016 SP1SOLIDWORKS 2015 SP5SOLIDWORKS 2014 SP5

Logopress3 Settings options:

You can set the default format of the standard component name (inserted with Standard

component library ).

In the Logopress3 settings options > Logopress3 General Options > Standardcomponent name format , you can enter the following keys:▪ %x : Remove project name. The project name is added by default to the name of thestandard component, except if you enter the %x key (not recommended).

In the Logopress3 settings options > Logopress3 Flattening > Attempt to make

the blank sketch entities tangent :This option is dedicated to stamped parts .▪ If deactivated (default): the sketch entities of the blank contour (segment and arcs) arenormally created (like in the previous version).▪ If activated: A smoothness is made attempting to make the contour entities tangent (if

possible). The contour can change slightly.NOTE : The former option Transform blank sketch curves into basic lines and arcs isnow unused and removed.


3/21


Progressive Blank Companion:

When the first start entity (selected in the Parameters tab, under Starting and/orPinching ) is exactly aligned with one of the boundary edges/faces (selected in the 3DStage tab, under Boundary edges/faces ), then the unforming direction can be ambiguous.In this case, a violet arrow appears on the first start entity: click on this arrow to reversethe direction.

Default directionClick on the violet arrow to

reverse the direction

Part nesting: All the used parameters and the list of selected parts to nest are memorized for next use

(file "file name"_LastValueNesting.tmp in the same folder as the files are stored) Choose the Type of nesting :

▪ In a sheet (default option)▪ In a strip layout (coil)


4/21


The nesting result can be created:▪ Either in a New document (default option)

After clicking OK , you can enter the name of the new document (default name ifyou click Cancel )

▪ Or in a New configuration Unused features (or parts) are suppressed in this configuration.

You can estimate the cutting time and cost of the nested parts, by filling-in the following parameters:▪ Cutting speed (m/min if metric document, or feet/min if IPS document)

▪ Cutting cost per hour (money unit in the Logopress3 settings options >Logopress3 General Options > Currency )NOTE : if these parameters are not filled-in (=0), then this estimation is not computed.

Part rotation to face .For face selection: Automatic 3D rotation of the part in order to move the selected face inthe working plane.Useful when parts are located in any position in space: it allows to easily re-position them

by simply selecting the face of the part that you want to be in the working plane.

Strip Layout:

In the Punch tab, under Punch parameters , you can set the Color/Transparency of

the selected punch . Create the mirror punch of the selected punch with respect to the Top plane of

the strip :Mirror punches are created with assembly mates (for easy manual change).

In Update all the cuts made by the punches dialog box ( Punch tab):You can set the Minimum volume of small bodies to retain in the strip skeleton.Ideal to clean-up a strip layout when the punch outline is not exactly created on the blanksketch contour and then generates small bodies.Below this minimum value (by default: 1e-009 mm 3 if metric document, or 6.1e-014 in 3 ifIPS document), the small bodies are deleted in the strip skeleton with a Delete Body feature.

The Excel file ( Strip summary information "Strip assembly name ".xls ) thatsummarizes the content of the information note, and that is created in the same folder asall the part files of the strip assembly are stored, has now the extension .xlsx .

Adding a diameter dimension called LgpDiaAttache in the sketch of a round part (notnecessarily a draw) allows to address it as a round draw part in the strip layout: then itgives access to all the types of skeleton template for round draw part, like 2 Webs , 3Webs or more , No web ...


5/21


NOTE : This sketch must be created on the Front plane and centered on the part origin(0,0,0).

New types of skeleton template for round draw part ( Type of link and number of rows ):

2 webs dog bone

2 webs V

3 webs or more in spiral

Blank nesting optimization : a new PropertyManager appears (same as the Partnesting module).


6/21


Choose the Type of nesting :▪ Old technology (old Blank nesting optimization . For 2 parts maximum)▪ In a strip layout (default option. Uses the new By combinatorial permutation nestingstrategy)

Punch tab > under Punch parameters > Create all the punches for the insidecuts of the selected part > Punches on other faces than the blank sketch .

No matter if the selected faces are plane or not plane , and parallel to the die plane or not parallel , the punches are automatically created from all the inside cuts of the selectedfaces with these set options:▪ Independent punch automatically activated▪ overall punch length automatically computed▪ penetration in the die automatically computed

Punch tab > under Punch parameters > Compute punch force :The former Compute punch force option is removed and replaced by this button:

▪ If activated / : the force of the selected punch is computed.

▪ If deactivated / : the force is not computed, but you can manually enter it.

NOTES :

o Warning! Be careful when changing this option to avoid incorrect punch forcecomputation.

By default the force computation is ACTIVATED for form punches/formdies that are created ABOVE the strip.

The force computation is DEACTIVATED for those that are createdUNDER the strip in order to avoid doubling the force on the bending/formingstations.

o When the force computation is deactivated in order to manually enter it, youcan also enter the force unit: daN, T, lbs.

If you don't enter the unit, the force is displayed in the chosen Force unit: or

depending on the document unit.This force is included in (or excluded from) in the main total force.

When you click Insert a station before the selected step or Delete the selected

station , the Ok button is replaced by an Apply button (same as Apply , orDetailed Preview ) in order to properly update the strip each time you are using these 2

options (for better result). Strip tab > under Part to insert in the strip > Part list :

You can select All parts to apply them the set parameters.


7/21


Standard component library 123Go Advanced:

Positioning by rotation .

▪ Until now you could Select the circular base edge with: sketch arc or circularedge.▪ From now you can also select: sketch point (endpoint or center of sketch entity),vertex.

For each type of mounting, the last used type of hole is memorized and proposed for nextuse (when possible).

Guide post mounting. Setting the stroke of the tool is no longer available. A messagewarns the user to control and manually set the ball bearing cages length.

Metric or Inch unit management of the user note/tolerance lists:The user note/tolerance lists, that are available by right-click in the tolerance fields of theSingle machining dialog box, can be customized inTolNoteUp.csv and TolNoteDown.csv files (previously located in \Logopress3installation directory \init ). Now:▪ Metric lists are located in \Logopress3 installation directory \init\Metric ▪ Inch lists are located in \Logopress3 installation directory \init\Inch

In the Single machining dialog box, the status of Wire EDM start hole option(activated/deactivated) is memorized for next creation of the current type of hole.

Editing/Modifying a Wire EDM start hole. Now, when editing a Wire EDM start hole, select the positioning point 2D sketch in theFeatureManager tree:▪ either in the sub-assembly where it is created (usually named "Sketch1_Wire EDM")▪ or in any plate containing this Wire EDM start hole where a sketch with coincident

points is created (also usually named "Sketch1_Wire EDM") New types of hole for the following types of Shoulder Bolt and Pad Retainer:

(codes: 421, 423, 424, 425, 426)o Under Shoulder Bolt Base Plate :

- Existing types of hole:

- New added types of hole:o Under Shoulder Bolt Length Plate :

- Existing type of hole:

- New added type of hole:o NOTES :

- These new hole types facilitate the additional insertion of a compression spring(that you can manually add with Add a standard component in the selected


8/21


plate under Standard components )- The corresponding customization files of standard components mountingcharacteristics ( perso xxx .csv ) are changed. If you have customized these files in a

previous version, you must update them by adding and completing the followingscolumns: DIA CBORE SCREW, HT CBORE SCREW, DIA CBORE LGT, HT

CBORE LGT.

New types of holes for this type of Pad Retainer-Reversed: (code 427)o Under Shoulder Bolt Base Plate :


- New added types of hole:o Under Shoulder Bolt Length Plate :

- Existing type of hole:

- New added type of hole:o NOTES :

- These new hole types facilitate the additional insertion of a compression spring(that you can manually add with Add a standard component in the selected

plate under Standard components )- The corresponding customization files of standard components mountingcharacteristics ( perso427.csv ) are changed. If you have customized these files in a

previous version, you must update them by adding and completing the followingscolumns: DIA CBORE SCREW, HT CBORE SCREW, DIA CBORE LGT, HTCBORE LGT.

New type of round hole: Counterbored tap (#46) (for jackscrew) New types of holes for the following types of screws:

(codes 401, 403, 404, 440)o Under Screw Head Plate :


- New added types of hole:


9/21


o NOTES :- These new types of hole are for jackscrew.- The corresponding customization files of standard components mountingcharacteristics ( perso xxx .csv ) are changed. If you have customized these files in a

previous version, you must update them by adding and completing the followings

columns: DIA JACK SCREW, PITCH JACK SCREW. New components:o STANDARD LIFTERS METRIC

STANDARD LIFTERS INCHDADCO METRICDADCO INCH:

Guided Keeper/Guide Retainer Set (Guidance and Retention - All in one)(code 428)

o BERGER:- Shouldered Demountable Guide Post ECO-7- Solid Bronze Demountable Bushing DBB- Steel Demountable Bushing DBS

Spring force computation:

You can highlight in the Graphics area the selected spring. Select it by right-click in theSpring list , and choose:▪ either Zoom to selection ▪ or Isolate (selecting another spring in the list deactivates automatically the Isolate mode)

Punch mounting:

Under Punch to mount , you can set the Color/Transparency of the selected punch .

Form punch and form die insert:


10/21


Under Formed Area On Strip , you can set the Color/Transparency of the selected

punch . Under Punch body , new type of punch: Marking punch . The selected part marks the

punch with its cavity.

1. Under Formed Area On Strip ,select only one face of the part thatmakes the cavity on the punch.

2. Under Punch body , select the typeof punch: Marking punch .3. Do the Punch body sketch

definition .NOTE : the sketch outline must notextend past the part overall dimensions.

4. If necessary, set the other parameters(punch length...).

5. Click OK .

Result: marking punch.


11/21


Sketches merging:

New type of merging:

Polygonal merging , with Milling radius and Offset . Select:

▪ Either sketches to mergeBefore After

▪ Or edges of Cut-Extrude to merge

Before After

NOTE : All the entities of the generated contour are tangent (if possible), regardless of thetype of merging.


12/21


Tool animation with interference detection:

Multibody parts (e.g.: plates with extruded wire EDM start holes) are managed in thedynamic interference detection.

When continuously pressing on the spin box arrow on the right side of the Manual

animation slider , then the tool animation is displayed in a continuous loop (start to end,start to end, etc.) until you release it.

Under Other components to animate , you can cancel the movement of a component tostop it moving.For example: you need to define several motions for a component (select several timesthis component in the graphics area in order to make it appear several times in the list:then for each of these instances, set the strokes and the moving direction).The first instance must be dedicated to cancel the default movement of this component(because it is animated with the tool part that includes it).

1. Select the component in the graphics area in order to make it appear in the list.2. Select the pre-set stroke depending on its location in the tool assembly. For

example: if the component is inserted in the upper part, select Linked to upperpart , and the strokes are automatically adjusted.

3. To cancel the movement of a component and to stop it moving:- The Distance from bottom of press stroke where animation of componentbegins is set to 0.- Retain the proposed Distance of press stroke during which the componenttravels .- Set the Distance that the component travels along the selected moving

direction with same value as previous one, but with a negative value (enter

the sign - or click Reverse the component moving direction or you can alsoclick the arrow to reverse it)NOTE : if you want to cancel the movement of a full sub-assembly (e.g.: median

part of the tool), then this last distance must be zero (or a value close to zero (like0.002mm) if zero is not accepted by the system).

4. Then you can re-select this component in the graphics area in order to defineanother movement.

Copy of set of components:

You can select a component individually:By default, when selecting a component, then the associated features (machining cuts,openings, holes...) and fasteners (holding screws...) are analyzed, searched and listed.

Now, selecting a component in the Graphics area by pressing ALT key allows toindividually select it (cancels the automatic search of every linked feature andcomponent).


13/21


In the Component to copy list, you can easily delete several parts from the list:Select one or several lines in the list of parts by pressing CTRL or SHIFT key, thenright-click and select Delete .

Sketch fillet management:

New type: Round corner clearance .Round corner clearance

1. The #1 Radius offset value parameter isset (1mm on the picture).

Round corner clearance with blend fillets

1. The #1 Radius offset value parameter isset (1mm on the picture).2. The #2 Blend fillet parameter is set (0.8on the picture).

Hole table:

You can manage the automatic creation of a Dowel Pin Symbol on dowel pin holeswhen generating the hole table:▪ in a part drawing: activate Tools > Options > Document Properties > Detailing >

Dowel symbols -part ▪ in an assembly drawing: activate Tools > Options > Document Properties > Detailing

> Dowel symbols -assembly NOTES :

▪ After setting this option, you can update the drawing with Edit and Update Tables .▪ It may be interesting to set this option in the default drawing templates (*.drwdot or*.slddrw).

You can manage the automatic creation of a Center mark on Wire EDM start holeswhen generating the hole table:


14/21


▪ in a part drawing: activate Tools > Options > Document Properties > Detailing >Center marks - holes -part

▪ in a assembly drawing: activate Tools > Options > Document Properties > Detailing > Center marks - holes -assembly

NOTES :▪ After setting this option, you can update the drawing with Edit and Update Tables .▪ It may be interesting to set this option in the default drawing templates (*.drwdot or*.slddrw).

Hole Callout:

Purpose:

To add driven diameter dimensions in a drawing to holes created by the Hole Wizard

or circular cut features, but also to holes created by Standard component library

123Go Advanced and Hole Library . Implementation:

1. Create the drawing of a plate, or open the drawing document of the plate.

2. Click Hole Callout in the Logopress3 toolbar, or click Logopress3 > HoleCallout .

The pointer changes to .3. On the top view, select a circular edge of hole.4. Click in the graphics area to place the hole callout.5. Repeat steps 3 through 4 to insert additional hole callouts, then press Esc to exit

the command. NOTE :

A warning text appears when positioning the first hole callout in the graphics area:"Warning! Logopress3 advanced Hole Callout – ONLY updated with registeredLogopress3 Die Design license"

Logopress3 Hole Table and/or Logopress3 Hole Callout can ONLY beupdated when the document changes with registered Logopress3 Die Design license.


15/21


What is fixed in this version?

1. BC1251. Fixed in 2016 SP0.3. Standard component library 123Go Advanced :

Screw mounting with Tapped (#28) hole type in the Tapped Hole Screw Plate: ifL1 dimension is changed, then another L0 dimension appears with no reason in the Single

machining dialog box.2. BC1250. Fixed in 2016 SP0.3. Spring force computation :

In some cases of tool design in IPS system unit, the computed spring force is wrong(divided by 2).

3. BC1249. Fixed in 2016 SP0.3. Standard component library 123Go Advanced :This message "An attempt was made to access an unnamed file past its end" appears when

editing the 2D point sketch of Stop Block with Edit the positioning sketch .


This message "An attempt was made to access an unnamed file past its end" appears whencreating a pilot from a favorite of pilot.5. BC1247. Fixed in 2016 SP0.3. Part nesting :

Correction and enhancement of the nesting algorithm when both dimensions of the sheetare entered.

6. BC1246. Fixed in 2016 SP0.3. Hole Table :

Exit of editing/modifying a hole table with Edit and Update Tables is slower thanwhen opening the drawing with the proposed hole table updating, due to aSOLIDWORKS issue of tag selection.


Screw mounting: when editing the mounting of a screw that is holding 3 plates in order tochange its diameter, then the hole diameter set in Other Plates Crossed Through doesn'tupdate automatically.


16/21



Dowel pin mounting with Counterdrill hole type: if ø counterdrilled hole < ødowel pin, then the chamfer is reversed when editing the mounting or copying it with

Standard component copy .9. BC1243. Fixed in 2016 SP0.3. Standard component library 123Go Advanced :

When the project name is ended by - (dash), and only in this case, and if a Machining axis

is copied with Standard component copy a first time, then the name of the copiedcomponents is truncated. If this copied Machining axis is copied again, then the name ofthe copied components becomes "projectname-projectname".

10. BC1242. Fixed in 2016 SP0.3. Hole Table :

The automatic creation of a Dowel Pin Symbol on dowel pin holes when generatingor updating the hole table erases all the Dowel Pin Symbols previously made by the user,even if this option is deactivated.

11. BC1241. Fixed in 2016 SP0.3. Standard component library 123Go Advanced :Error when inserting a GENERIC INCH Socket Head Cap Screw #8-32: it creates a #8-36tapped hole.

12. BC1240. Fixed in 2016 SP0.3. Copy of set of components :

The Isolate the components to copy button is no longer working.

13. BC1239. Fixed in 2016 SP0.3. Strip Layout :

Small part may not be properly rebuilt with Update the stations of the annex partused in the strip when adding/removing tiny features (2 x CTRL+Q is now made during

the Blank section sketch rebuilding of the annex part for strip in order to work around thisissue).

14. BC1238. Fixed in 2016 SP0.3. Strip Layout :A mirror part that is inserted in the strip (with Create and insert the mirrored part of

the selected part function) may not be properly rebuilt with Update the stationsof the annex part used in the strip .

15. BC1237. Fixed in 2016 SP0.3. Hole Table :In some table updating cases (e.g.: Ctrl+Q in the main assembly, open the drawing andselect No when asking to update the BOM table, then Ctrl+Q in the drawing), a wrongwarning message may appear (Logopress3 Hole Table and/or Logopress3 Hole Callout

cannot be updated when the document changes, because you only have a 123Go access)even with a Die Design license.

16. BC1236. Fixed in 2016 SP0.2. Standard component library 123Go Advanced :IMPAX BASIC INCH and IMPAX VARIABLE INCH: Extended Range Solid andEjector punches were missing (308.csv, 309.csv, 310.csv and 311.csv).


17/21


17. BC1235. Fixed in 2016 SP0.2. Strip Layout :

Blank nesting optimization > In a strip layout : The part may be reversed upsidedown by mistake.

18. BC1234. Fixed in 2016 SP0.1. Registration/License request :Wrong version number in LgpReginfo.txt file.

19. BC1233. Fixed in 2016 SP0.1. Standard component library 123Go Advanced :Error when inserting a GENERIC INCH Low Head Cap Screw (mistake in 411.csv file).

20. BC1232. Fixed in 2016 SP0. Standard component library 123Go Advanced :

Standard component copy (with Wire EDM start hole option activated) in anew plate: the Wire EDM start holes are not created in the copies, and those of theoriginal components are moved.

21. BC1231. Fixed in 2016 SP0. Strip Layout :

You can now mirror a shear punch (and its split sketch , made with Scrapcutting punch option).

22. BC1230. Fixed in 2016 SP0. Strip Layout :When several different parts with same thickness are inserted in the strip, it may happensometimes that they're considered not having the same thickness.

23. BC1229. Fixed in 2016 SP0. Strip Layout :When mirroring a group of punches that are created from the copy of the firstoriginal punch, then all the mirrored punches are superimposed on the mirror punch of thefirst original one!

24. BC1228. Fixed in 2016 SP0. Strip Layout :In some cases, the force computation in the strip layout is not properly updated in case ofstrip width or step/pitch change.

25. BC1227. Fixed in 2016 SP0. Standard component library 123Go Advanced :In the points positioning 2D sketch, when the Standard component preview on the

pointer is deactivated, some standard component preview appear at the ends of lines(not created, only displayed).

26. BC1226. Fixed in 2016 SP0. Standard component library 123Go Advanced :When editing a punch/pilot mounting: the plug or the pilot is not found in the database.


18/21


27. BC1225. Fixed in 2016 SP0. Form Punch and Form Die Insert :When editing a form punch created at tool assembly level and changing its type (e.g.:from 2D punch #1 to 2D punch #2 ): plane, sketch and cut-extrude features of the bend

profile are not properly rebuilt and warnings remain displayed.28. BC1224. Fixed in 2016 SP0. Hole Table :

Hole diameter tolerance may not appear in the hole table if a pocket is made afterwardsabove the hole.

29. BC1223. Fixed in 2016 SP0. Punch mounting :When inserting several strips that have the same project name in the tool, then only the

punches of the first inserted strip can be mounted in the tool.(Possible workaround by changing the project name of other strip sub-assemblies)

30. BC1222. Fixed in 2016 SP0. Bill Of Materials :Updating BOM tables that are split and located in other sheets doesn't works properly.

31. BC1221. Fixed in 2016 SP0. Standard component library 123Go Advanced :Ball-lock punch/pilot mounting. If the top face of the upper block is selected as base face(instead of the bottom face), then the preview is correct but the final mounting is made inthe reversed way on top direction! Now it works like the preview.

32. BC1220. Fixed in 2016 SP0. Standard component library 123Go Advanced :Impossible to insert a ball-lock punch if the dowel pin and screw holes of the punchretainer are outside the cutting die (on top vue), because the punch retainer is larger thanthe cutting die.

33. A1230. Fixed in 2016 SP0. Strip Layout :The OpenGL cutting preview must be hidden for punches that have the following setoptions:▪ Independent punch (activated)

▪ Cut the skeleton (deactivated)▪ Cut the part (deactivated)

34. A1225. Fixed in 2016 SP0. Standard component library 123Go Advanced :The Hole description for the hole table in the Single machining dialog box is limited to28 characters. Now, no limit for this string length.

35. BC1216. Fixed in 2016 SP0. Add an insert :The Comment custom property is not properly set with the file name (like plates), italways displays Insert or Shim .

36. BC1215. Fixed in 2016 SP0. Punch mounting :When there are several strips in the tool, some punches may not be correctly located after

being mounted. It's because there's only one "sub-assembly of punches mounted in thetool". Now, there's one "sub-assembly of punches" per strip.


19/21


37. BC1211. Fixed in 2016 SP0. Tool structure :

Add plate > Plate from sketch : The used default template of Plate from sketch is

wrong when a network path is specified in the Logopress3 options > Logopress3General Options > template field. When this path is specified, then it replaces the

default file location. But in this case, it is still using the default template that is defined inthe local file location (Logo3partSketchPlate.SLDPRT under \Logopress3 installationdirectory \template\english\drawing\Metric or \Inch ).

38. BC1206. Fixed in 2016 SP0. Part nesting :In an assembly, the nesting of parts with configurations is made as per the configurationsaved with the part instead of in accordance with the configuration of the part in theassembly.

39. BC1203. Fixed in 2016 SP0. Station mark :When possible, the station marks are now created without any parent/child relationshipswith other features.

40. BC1202. Fixed in 2016 SP0. Tool structure :When adding a plate from a plate template that has an associated drawing, then thecreation date of the new drawing (Date created) is not updated and retains the creationdate of the original drawing template.

41. BC1201-a. Fixed in 2016 SP0. Tool structure :

When saving the current tool as tool template (with Save as tool template ), it's nowsaved in \Logopress3 installation directory \template\english\tools with respect to thedefault file tree organization:

tool template name.sldasm tool template name (folder where every component file and its associated drawing is

copied)StdElts (sub-folder where every standard component file is copied)

No matter the status (activated/deactivated) of both Logopress3 options >Logopress3 General Options >▪ Create the standard components in a sub-directory ...\StdElts ▪ Create the part files of the tool in a sub-directory

42. BC1201-b. Fixed in 2016 SP0. Tool structure :

When inserting a tool sub-assembly (previously made with Tool structure or not) at

the top level of the main tool assembly with the button Add a tool sub-assembly , it'snow inserted with respect to the original file tree organization.



20/21


43. BC1201-c. Fixed in 2016 SP0. Save as... with new project name :When saving a copy of the current tool sub-assembly in a new folder with Logopress3 >Save as... with new project name , this new copy is created with respect to the originalfile tree organization.


44. BC1201-d. Fixed in 2016 SP0. Logopress3 options > Logopress3 GeneralOptions :▪ Create the standard components in a sub-directory ...\StdElts : it only impacts thecreation of new standard components in the current tool assembly.▪ Create the part files of the tool in a sub-directory : it only impacts the creation of new

plates in the current tool assembly.

45. BC1200. Fixed in 2016 SP0. Tool structure :

When saving the current tool as tool template (with Save as tool template ), someuseless files (.csv, .body, .lgp3Blank, .xls…) are copied in the folder \Logopress3installation directory \template\english\tools .

46. BC1198. Fixed in 2016 SP0. Progressive Blank Companion :Excluded faces that are selected under Faces to exclude in the Parameters tab, arelost if a pinched entity is selected under Pinching in the 3D Stage tab.

47. BC1187. Fixed in 2016 SP0. Standard component library 123Go Advanced :When editing a machining axis with custom component: the custom component file namechanges unexpectedly, its prefix becomes "StdElts".

48. BC1180. Fixed in 2016 SP0. Smart Ordinate Dimensions for Holes :If a default layer is set in Options > Document Properties > Dimensions > Ordinate >Layer , then the Ordinate Dimensions are not created on this layer.

49. BC1179. Fixed in 2016 SP0. Strip Layout :When moving 2D Bending punches, they are correctly moved, but sometimes an errormay appear: the relations that are used to define the profile sketch plane are lost.

50. BC1178. Fixed in 2016 SP0. Delete Standard Component :Delete a standard component when the strip is hidden with the filter Hide/Show the strip

assembly , then all the parts of the strip (skeleton + annex part) are hidden!

51. BC1177. Fixed in 2016 SP0. Sketch fillet management :Chamfer Offset . If the offset value is changed, and you Select 'Yes' to update thisparameter with its new value , then nothing happened.

52. BC1176. Fixed in 2016 SP0. Edit the positioning sketch :When editing the positioning sketch of a machining axis, and deleting the first created

point, then the other components are not correctly positioned (located anywhere) aftervalidation.


21/21


53. BC1175. Fixed in 2016 SP0. Add an insert :When editing an insert and changing the material, then the new material is lost aftervalidating, it retains the old material.

54. BC1174. Fixed in 2016 SP0. Add an insert :

In the Insert file name field, if the string is cleared to enter another name, then the project name is not added to the new insert filename. Now it's automatically added.

55. BC1173. Fixed in 2016 SP0. Standard component library 123Go Advanced :Delete a Wire EDM start hole created with extrude/surface option doesn't delete all theassociated bodies in the crossed plates.

56. BC1172. Fixed in 2016 SP0. Standard component library 123Go Advanced :Punch/pilot mounting. The counterbore depth can no longer be reversed by mistake (whenmounting a shouldered button die longer than the die plate thickness).

In order to have the chronological account of the news linked to the former releases, please go toRelease Notes.

Documents

Logopress3 News 2016 SP0-x