General Details

Product Description

USG Logix Panel optionsHalcyonTM, MarsTM, MarsTM High-NRC, Panz®, Logix Connector Panels and TrueTM Wood.

USG Logix Suspension System options

USG Logix Yoke

USG Utility Module Bracket (UMB)

General Product Use

ver 5.0 Page 1 of 7

3. All construction, wood or steel framing, beams, joist, stringers and associated connections needed to support the Logix IntegratedCeiling System are outside the scope of this PER. All construction shall follow applicable codes or be designed by a licensed Engineer.Building structure must be capable to withstand the applicable loads required by Chapter 16 of the 2012, 2015 and 2018 IBC.

4. All USG DONN brand suspension systems, when used with any USG ceiling panels or tiles, carry a lifetime (30-year) warranty that USGproducts shall be free from manufacturing defects and that the suspension systems shall be free from the occurrence of 50% red rust asdefined by ASTM D610 test procedures for 30 years from the date of installation.

5. Finish is not UV-resistant. All USG DONN Brand Suspension Grid Systems should not be installed where direct exposure to sun orweather.

This report covers the USG Logix Suspension System and USG Utility Module Bracket manufactured by USG Interiors, LLC. The plantlocations listed above have an approved Quality Control Manual to manufacture the products. USG Interiors, LLC has a ProductEvaluation Service Agreement with Pei Evaluation Service® and Follow-up Inspection Service Agreement with ProgressiveEngineering Inc. (Pei ). The plant locations listed above shall be inspected quarterly by Pei .

The Logix Systems described in this report, are assemblies used in interior general-use areas. The suspended ceiling systems consist ofmain and cross tee framing members with lay-in ceiling panels. There are a variety of clips, yokes, brackets and other accessoriesavailable for the system. The suspension system main tees, cross tees, and accessories are manufactured using steel with a minimumyield strength of 30 ksi and a minimum G30 hot-dipped galvanized coating.

The suspension System can create narrow 4", 6", 12", 100mm, 150mm and 300mm channels. Ceiling panels are supported by USG Interiors CENTRICITEETM DXTTM, IDENTITEETM DXITM, DONN® DX®/DXLTM and FINELINE® DXFTM.

The Yoke is an optional suspension system installation accessory that facilitates the spacing and suspension of parallel main tees withone hanger wire. The Yoke is compatible with both Metric and Imperial channel sizes. The Yoke also keeps hanger wire wraps away fromlinear luminaires, can reduce the number of hanger wires required and helps brace the utility channel. Designed to work with the USG Logix Suspension System options listed in this PER.

This bracket is a convenient and versatile suspension system accessory, designed to easily create Logix utility channels with StandardUSG ceiling grids. The USG Utility Module Bracket can also be used to create intersecting utility channels. The USG Utility ModuleBracket is designed to work with the following suspension systems: CENTRICITEE DXTTM, IDENTITEE DXI, DONN DX/DXL.

1. Logix Integrated Ceiling Systems shall be installed in accordance with the Logix installation guide and are subject to the conditions ofthis PER. A copy of the installation guide shall be made easily available to the installer.2. Complies with ASTM C635, ASTM C645 and must be installed in accordance with ASTM C636, ASTM E580, CISCA and standardindustry practices, within applicable code requirements.

July, 2020

Pei Evaluation Service® is an accredited ISO Standard 17065 Product Certifier,accredited by the IAS. This Product Evaluation Report represents a product that Pei ES has Evaluated. This product has a Product Evaluation Service Agreement &Follow-up Inspection Service Agreement. This Product Evaluation Report in noway implies warranty for this product or relieves USG Interiors, LLC and CGCInteriors, LLC of their liabilities for this product. This PER is an official document if itis within one year of the initial or re-approval date.

Initial ApprovalJuly, 2014

Re-Approved

See all Pei ES Listings at: www.p-e-i.com

Approved Manufacturing Locations

Evaluation Report Informationusg4you@usg.com

USG Support: 800.USG4YOU

ProductLogixTM Integrated Ceiling Systems:LogixTM Modules and LogixTM Utility Channels

Report OwnerUSG Interiors, LLC550 West Adams StreetChicago, Illinois 60661

PER-12056

USG Interiors, LLCPlant # 601

1000 Crocker Rd.Westlake, OH 44145

USG Interiors, LLCPlant # 603

2575 East Loomis Rd.Stockton, CA 95205

USG Interiors, LLCPlant # 605

1000 Donn Dr.Cartersville, GA 30120

CGC Interiors, LLCPlant # 091

735 Fourth Line Rd.Oakville, Ontario, Canada L6L 5B7

Properties Evaluated

Code Compliance Meets requirements for Suspended Ceilings in accordance with:

Compliance with the following Standard

ASTM C645 - Standard Specification for Nonstructural Steel Framing Members

ASTM C636 - Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in PanelsASCE7 - Minimum Design Loads for Buildings and Structures

Seismic Classification

Load Ratings

Page 2 of 7

Table 1 - Seismic Design Classification

ASTM C635 - Standard Specification for the Manufacture, Performance and Testing of Metal Suspension Systems for Acoustical Tile andLay-in Panel Ceilings

ASTM E580 - Standard Practice for Application of Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels in Areas RequiringModerate Seismic RestraintASTM E84 - Standard Test Method for Surface Burning Characteristics of Building MaterialsClassified - Class A as required by Sections 803.1.1 of the IBC for panels

Meets the requirements of ASTM C635 and installation requirements of ASTM C636 as required in the 2012, 2015 and 2018 IBC (2013CBC) sections shown above.

Meets the requirements for Class A in accordance with Section 803.1.1 of the 2012, 2015 and 2018 IBC (2013 CBC), as tested inaccordance with ASTM E84.

Meets the requirements for seismic resistive suspension ceiling in accordance with Section 13.5.6 of ASCE 7-10 as tested in accordanceto AC156 as required by Section 1613 of the 2012, 2015 and 2018 IBC (2013 CBC).

ASTM A653 - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-DipProcess

Interior Ceiling Installation: The systems have been evaluated to comply with requirements for interior installations. The systems aboveare tested in accordance with ASTM C635, ASTM C636, ASTM C645, ASTM E580 and AC 156.

2012, 2015 & 2018 International Building Code® (IBC), International Residential Code© (IRC) and 2013 California Building Code (CBC).

PER-12056

Seimsic Design Category A, B Seimsic Design Category C Seimsic Design Category D, E, FNo Requirement Intermediate Duty Heavy Duty

DXL 24* Intermediate DutyDXL 26 Heavy DutyDXT 24 Intermediate DutyDXT 26* Heavy DutyDXI 24 Intermediate DutyDXI 26 Heavy Duty

DXF 2924* Intermediate DutyDXFH 2924 Heavy Duty

Notes:

1. ASTM Class is valid when the ceiling grid is installed in accordance with ASTM C636 and/or ASTM E580. Alternative installations have been seismically qualified through shake table testing in accordance with ICC-ES AC156.

2. Rated loads are based upon the minimum of the load at a deflection limit of L/360 and the ultimate bending capacity divided by a safety factor of 2.0. *Exception: Rated loads are based upon L/360 deflection only.

16 8.9 5.2

6.85.23.9

Table 2 - Rated Loads

9.16.2

5.23.6

12 6.8 3.9

5.34.27.3

9.21612

1612

9.1

1612

Main Tee ASTM Class1 Rated Load2 (lb/ft)4' Hanger Spacing 5' Hanger Spacing 6' Hanger Spacing

Section 803.1.2 Table 803.13Section 808.1 Section 2506.2

2012, 2015 & 2018 International Residential Code

2012 & 2015 International Building Code

Section R302.9

Section 803.1.1 Table 803.11

Section 2506.2.1

Section 1613 - In Compliance with Requirements

Section 808.1

2018 International Building Code

Section 1613 - In compliance with requirements

Profile Details

Page 3 of 7

PER-12056

Page 4 of 7

PER-12056

Figure 5 - Logix Channel Cross Members

Page 5 of 7

PER-12056

4" Panel 6" Panel

Figure 7 - Logix Connector Panels

Page 6 of 7

PER-12056

Product Labeling

1. USG Interior, LLC Name and Address2. Product Name3. Plant Identifier & Date Code4. Pei ES Information: See Pei Evaluation Report at p-e-i.com5. UL Back Stamp Information for Fire Resistance6. Image of Permanent Label on Main Tee for Miami-Dade Resistance7. ICC-ES ESR Report Number

Acceptable Evaluation Marks

Product DocumentationA Product Evaluation Service Agreement between Pei Evaluation Service® and USG Interiors, LLCA Follow-up Inspection Service Agreement between Progressive Engineering Inc. and USG Interiors, LLC

Various Test Reports and Rated Load Calculations Submitted by USG Interiors, LLC.USG Interiors, LLC Q.C. Manual for DONN® Brand Suspension Systems and USG Drywall Suspension Systems - Dated: 11/12/2018

Each Grid system shipment assembly, that is covered by this Product Evaluation Report (PER), must have a label attached with atleast the following information:

Page 7 of 7

PER-12056