LOADER ATTACHMENTS AE11 AF11 - John Deeremanuals.deere.com/cceomview/5MP76312_19/Output/5MP76312.pdfab16 ae11 af11 af12 ag10 ah11 as10 as11 manual #5mp76312 m-1474 6-25-12-7 operator’s

AB16AE11AF11AF12AG10AH11AS10AS11

MANUAL #5MP76312

M-1474 6-25-12-7

OPERATOR’S AND PARTS MANUAL

SPECIALTYLOADER ATTACHMENTS

76312 1

TABLE OF CONTENTSPREFACE..................................................................................................................................................................................... 2SAFETY PRECAUTIONS Safety Statements .......................................................................................................................................................... 3 General Safety Precautions ........................................................................................................................................ 3-5 Equipment Safety Precautions .................................................................................................................................... 6-7SET-UP ....................................................................................................................................................................................... 8INSTALLATION Attaching and Detaching Equipment - 200/300/400/500 Series Loaders ...................................................................... 9 Attaching and Detaching Equipment - 600/700/800 Series Loaders ...................................................................... 10-11 Attaching and Detaching Equipment - Global Carrier Series Loaders .................................................................... 11-12OPERATION AG10 Series Silage Defacer Operation ....................................................................................................................... 13 AE11 Series Free Stall Scraper Operation ................................................................................................................... 14 AF11 & AF12 Series Loader Mounted Front Blade Operation ................................................................................ 15-17 AS10 & AS11 Series Snow Push Operation ................................................................................................................ 18 AB16 Series Small Square Bale Fork Operation ......................................................................................................... 19 AH11 Series Bale Hugger Operation ........................................................................................................................... 20MAINTENANCE Lubrication & Daily Maintenance.................................................................................................................................. 21 Decal Replacement ...................................................................................................................................................... 22 Monthly Maintenance ................................................................................................................................................... 22 Chain Adjustment (AG10 Series Silage Defacer)......................................................................................................... 22 Blade Replacement (AG10 Series Silage Defacer) ..................................................................................................... 23 Rubber Edge Replacement .................................................................................................................................... 23-24 Cylinder Seal Replacement..................................................................................................................................... 25-26SPECIFICATIONS AttachmentSpecifications ............................................................................................................................................ 27 BoltTorqueSpecifications ............................................................................................................................................ 29

PARTS AG10 SERIES SILAGE DEFACER (600/700/800/Global Carrier Series Loader).................................................. 30-33 AE11 SERIES FREE STALL SCRAPER (300/400/500 Series Loader) .................................................................. 34-35 OPTIONAL PULL BACK ASSEMBLY (Free Stall Scraper) ..................................................................................... 36-37 AF11E 72” LOADER MOUNTED FRONT BLADE (300/400/500 Series Loader) ................................................... 38-39 AF11E 84” LOADER MOUNTED FRONT BLADE (300/400/500 Series Loader) ................................................... 40-41 AF11D & AF11G 84” LOADER MOUNTED FRONT BLADE (600/700/Global Carrier Series Loader) ................... 42-43 AF11D & AF11G 96” LOADER MOUNTED FRONT BLADE (600/700/Global Carrier Series Loader) ................... 44-45 AF12D & AF12G 96” LOADER MOUNTED FRONT BLADE (600/700/Global Carrier Series Loader) ................... 46-47 AF12D & AF12G 108” LOADER MOUNTED FRONT BLADE (600/700/Global Carrier Series Loader) ................. 48-49 AF12D & AF12G 110” LOADER MOUNTED FRONT BLADE (600/700/Global Carrier Series Loader) ................. 50-51 HYDRAULIC ANGLE KIT 5FP10726 (Loader Mounted Front Blade) ..................................................................... 52-53 OPTIONAL RUBBER EDGE ASSEMBLIES (Loader Mounted Front Blade) .......................................................... 54-55 OPTIONAL TOP FLAP ASSEMBLIES (Loader Mounted Front Blade) ................................................................... 56-57 AS10 SERIES SNOW PUSH (300/400 Series Loader) .......................................................................................... 58-59 AS11 SERIES SNOW PUSH WITH TRIP EDGE (300/400/500 Series Loader) ..................................................... 60-61 OPTIONAL PULL BACK ASSEMBLIES AND RUBBER EDGE ASSEMBLIES (AS11 Series Snow Push) ............ 62-63 AB16 SERIES SMALL SQUARE BALE FORK (600/700/800/Global Carrier Series Loader) ................................. 64-67 AH11 SERIES BALE HUGGER (600/700/800/Global Carrier Series Loader) ....................................................... 68-69 HYDRAULIC KIT 5MP107670 ................................................................................................................................ 70-71 5FPLAF4563 CYLINDER ASSEMBLY (Used On AF11 Series Loader Mounted Front Blade) ............................... 72-73 5FP035733 CYLINDER ASSEMBLY(Used On AF12 Series Loader Mounted Front Blade) .................................. 74-75 5FPLAF4044 CYLINDER ASSEMBLY SERVICE PARTS ..................................................................................... 76-77 5MP88928 CYLINDER ASSEMBLY (Used on AB16 Series Small Square Bale Fork) ........................................... 78-79 5MP104708 CYLINDER ASSEMBLY (Used on AH11 Series Bale Hugger) ........................................................... 80-81

76312 32 76312

PREFACE SAFETY STATEMENTS

DANGER

GENERAL SAFETY PRECAUTIONS

WARNING! READ MANUAL PRIOR TO INSTALLATIONImproper installation, operation, or maintenance of this equipment could result in serious injury or death. Operators and maintenance personnel should read this man-ual, as well as all manuals related to this equipment and the prime mover thoroughly before beginning installation, operation, or maintenance. FOLLOW ALL SAFETY INSTRUCTIONS IN THIS MANUAL AND THE PRIME MOVER’S MANUAL(S).

READ AND UNDERSTAND ALL SAFETY STATEMENTSRead all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all OSHA regulations, local laws, and other professional guidelines for your operation. Know and follow good work practices when assembling, maintaining, repairing, mounting, removing, or operating this equipment.

KNOW YOUR EQUIPMENTKnow your equipment’s capabilities, dimensions, and operations before operating. Visually inspect your equipment before you start, and never operate equipment that is not in proper working order with all safety devices intact. Check all hardware to ensure it is tight. Make certain that all locking pins, latches, and connection devices are properly installed and secured. Remove and replace any damaged, fatigued, or excessively worn parts. Make certain all safety decals are in place and are legible. Keep decals clean, and replace them if they become worn or hard to read.

WARNING

CAUTION

THIS SIGNAL WORD IS USED WHERE SERIOUS INJURY OR DEATHWILL RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY.

THIS SIGNAL WORD IS USED WHERE SERIOUS INJURY OR DEATHCOULD RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY.

THIS SIGNAL WORD IS USED WHERE MINOR INJURY COULD RESULT IF THE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY.

NOTICE INDICATES A PROPERTY DAMAGE MESSAGE. NOTICE

THIS SYMBOL BY ITSELF OR WITH A WARNING WORD THROUGHOUT THIS MAN-UAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY OR THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.

WARNING! Never let anyone operate this unit without reading the "Safety Precautions" and "Operations" sections of this manual.

Always choose hard, level ground to park the loader on and set the brake so the unit cannot roll.

BEFORE OPERATION The primary responsibility for safety with this equipment falls to the operator. Make sure the equipment is operated only by trained individuals that have read and understand this manual. If there is any portion of this manual or function you do not understand, contact your local Frontier Dealer.

SERVICE When servicing your product, remember to use only manufacturer replacement parts. Substitute parts may not meet the standards required for safe, dependable operation. To facilitate parts ordering, record the model and serial number of your unit in the space providedonthispage.Thisinformationmaybeobtainedfromtheidentificationplatelocatedon the product. Any questions related to this attachment should be directed to your local Frontier dealer.

MODEL:__________________________ DATE: ______________________________

SERIAL NUMBER: ___________________________ (See parts section for location.)

¡LEA EL INSTRUCTIVO!Si no lee Ingles, pida ayuda a

alguien que si lo lea para que letruduzca lasmedidas de sequridad.

GENERAL INFORMATION The purpose of this manual is to assist you in operating and maintaining your attach-ment. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. Theseinstructionshavebeencompiledfromfieldexperienceandengineeringdata.Some information may be general in nature, due to unknown and varying operating conditions. However, through experience and these instructions, you should be able to develop proce-dures suitable to you particular situation. The illustrations and data used in this manual were current at the time of printing. How-ever, due to possible inline production changes, your machine may vary slightly in detail. We reservetherighttoredesignandchangethemachinesasmaybenecessarywithoutnotifica-tion. Throughout this manual, references are made to right and left direction. These are de-termined by standing behind the tractor facing the direction of forward travel.

76312 54 76312


WARNING! PROTECT AGAINST FLYING DEBRISAlways wear proper safety glasses, goggles, or a face shield when driving pins in or out,orwhenanyoperationcausesdust,flyingdebris,oranyotherhazardousmate-rial.

WARNING! LOWER OR SUPPORT RAISED EQUIPMENTDo not work under raised booms without supporting them. Do not use support mate-rial made of concrete blocks, logs, buckets, barrels, or any other material that could suddenly collapse or shift positions. Make sure support material is solid, not de-cayed, warped, twisted, or tapered. Lower booms to ground level or on blocks. Lower booms and attachments to the ground before leaving the cab or operator’s station.

WARNING! USE CARE WITH HYDRAULIC FLUID PRESSUREHydraulicfluidunderpressurecanpenetratetheskinandcauseseriousinjuryordeath. Hydraulic leaks under pressure may not be visible. Before connecting or dis-connecting hydraulic hoses, read your prime mover’s operator’s manual for detailed instructionsonconnectinganddisconnectinghydraulichosesorfittings.

• Keep unprotected body parts, such as face, eyes, and arms as far away as possiblefromasuspectedleak.Fleshinjectedwithhydraulicfluidmaydevelopgangrene or other permanent disabilities.

• Ifinjuredbyinjectedfluid,seeadoctoratonce.Ifyourdoctorisnotfamiliarwiththis type of injury, ask him to research it immediately to determine proper treat-ment.

• Wear safety glasses, protective clothing, and use a piece of cardboard or wood when searching for hydraulic leaks. DO NOT USE YOUR HANDS!

SEE ILLUSTRATION.

CARDBOARD

HYDRAULIC HOSEOR FITTING

MAGNIFYING GLASS


WARNING! DO NOT MODIFY MACHINE OR ATTACHMENTSModificationsmayweakentheintegrityoftheattachmentandmayimpairthefunc-tion, safety, life, and performance of the attachment. When making repairs, use only themanufacturer’sgenuineparts,followingauthorizedinstructions.Otherpartsmaybesubstandardinfitandquality.NevermodifyanyROPS(RollOverProtectionStructure) or FOPS (Falling Object Protective Structure) equipment or device. Any modificationsmustbeauthorizedinwritingbythemanufacturer.

WARNING! SAFELY MAINTAIN AND REPAIR EQUIPMENT• Do not wear loose clothing or any accessories that can catch in moving parts. If

you have long hair, cover or secure it so that it does not become entangled in the equipment.

• Work on a level surface in a well-lit area.• Use properly grounded electrical outlets and tools.• Use the correct tools for the job at hand. Make sure they are in good condition for

the task required.• Weartheprotectiveequipmentspecifiedbythetoolmanufacturer.

SAFELY OPERATE EQUIPMENTDonotoperateequipmentuntilyouarecompletelytrainedbyaqualifiedoperatorin how to use the controls, know its capabilities, dimensions, and all safety require-ments. See your machine’s manual for these instructions.• Keep all step plates, grab bars, pedals, and controls free of dirt, grease, debris,

and oil.• Never allow anyone to be around the equipment when it is operating.• Do not allow riders on the attachment or the prime mover.• Do not operate the equipment from anywhere other than the correct operator’s

position. • Never leave equipment unattended with the engine running, or with this attach-

ment in a raised position.• Do not alter or remove any safety feature from the prime mover or this attach-

ment.• Knowyourworksitesafetyrulesaswellastrafficrulesandflow.Whenindoubt

on any safety issue, contact your supervisor or safety coordinator for an explana-tion.

WARNING! KNOW WHERE UTILITIES AREObserve overhead electrical and other utility lines. Be sure equipment will clear them. When digging, call your local utilities for location of buried utility lines, gas, water,andsewer,aswellasanyotherhazardyoumayencounter.

76312 76 76312

EQUIPMENT SAFETY PRECAUTIONS

TRANSPORTING ALL ATTACHMENTS• Travel only with the attachment as close to the ground as possible. Drive slowly over

rough ground and on slopes.• Whendrivingonpublicroadsusesafetylights,reflectors,SlowMovingVehiclesigns

etc., to prevent accidents. Check local government regulations that may affect you.• Do not drive close to ditches, excavations, etc., cave in could result.• When on a slope, keep the load low and proceed with extreme caution. Do not drive

ACROSS a steep slope - drive straight up and down. With a LOADED attachment - face the attachment and load uphill. With an EMPTY attachment - face the attachment downhill.• Do not smoke when refueling. Allow room in the gas tank for expansion. Wipe up any

spilled fuel. Secure cap tightly when done.

MAINTAINING ALL ATTACHMENTS• Before performing maintenance, lower the attachment to the ground, apply the brakes,

turn off the engine, and remove the key.• Worn, damaged, or illegible safety decals must be replaced. New safety decals can be

ordered from your Frontier Dealer.• Never work under a raised attachment.

OPERATING ALL ATTACHMENTS• Operate only from the operator’s station. Always use the seat belt if the prime mover

has a ROPS. Do not use a seat belt if there is not ROPS. Check the seat belt daily and replace if frayed or damaged.

• Specifiedliftcapacitiesmustnotbeexceeded.Seeloaderspecifications.• An operator must not use drugs or alcohol, which can change his or her alertness or co-

ordination. An operator taking prescription or over-the-counter drugs should seek medi-cal advice on whether or not he or she can safely operate equipment.

• Never use any of these attachments for a work platform or personnel carrier.• Always check locking pins before tilting or operating any attachment.• Do not handle round bales unless loader is equipped with approved bale handling at-

tachments.• Do not detach loader from tractor with any of these attachments installed. Equip loader

with material bucket when detaching.• Stop loader gradually when lowering or lifting loads• Before exiting the prime mover, lower the attachment to the ground, apply the brakes,

turn off the prime mover’s engine, and remove the key.• Add the required amount of ballast to tractor. (See Preparing the Tractor section of the

Loader Operator’s Manual to determine the type and amount of ballast required.)

ADDITIONAL PRECAUTIONS FOR AG10 SERIES SILAGE DEFACER• Clear work area of ALL bystanders before operating this attachment.• Operate only from the operator’s station.

ADDITIONAL PRECAUTIONS FOR AE11 SERIES FREE STALL SCRAPER

• Pushing rigid objects or material can result in damage to the scraper.

ADDITIONAL PRECAUTIONS FOR AF11 AND AF12 SERIES LOADER MOUNTED FRONT BLADE• Dozingundisturbedsoilorheavymaterialcanresultindamagetotheblade.• Do not operate the AF11 Series blade onto 7000 series tractors. The horsepower and

overall vehicle weight will exceed the working capacity of the blade

ADDITIONAL PRECAUTIONS FOR AS10 AND AS11 SERIES SNOW PUSH

• Pushing rigid objects or material can result in damage to the snow push.

ADDITIONAL PRECAUTIONS FOR AB16 SERIES SMALL SQUAREBALE FORK• Park and store this attachment with tines pointed down.• Do not handle more bales than your attachment was designed to lift.• Never stack bales on uneven ground. Loads stacked on uneven ground can topple.

ADDITIONAL PRECAUTIONS FOR AH11 SERIES BALE HUGGER• Do not handle more than one round bale at a time.• Be sure stack and load heights do not exceed the lifting capabilities of your loader.• Never use tractor or loader to stop a rolling bale.

EQUIPMENT SAFETY PRECAUTIONS

REAR TIRE BALLAST600/700/800/GLOBAL CARRIER SERIES LOADERS

REAR TIRE BALLAST 200/300/400/500 SERIES LOADERS

REAR BALLAST BOX WARNING! TRACTOR STABILITY OR LOSS OF

STEERING CONTROL MAY RESULT IF BALLAST BOX IS INSTALLED WITHOUT LOADER. DO NOT OPERATE TRACTOR WITH BALLAST BOX UNLESS LOADER

IS INSTALLED.

76312 98 76312

INSTALLATIONSET-UP

GENERAL INFORMATION The AE11 Series free stall scraper, the AS10 Series snow push, the AB16 Series small square bale fork, the AH11 Series bale hugger, and the AG10 Series silage defacer are shipped completely assembled and ready to install without any set-up required.

AF11 AND AF12 SERIES LOADER MOUNTED FRONT BLADES With the blade properly attached to the loader and parked on a hard level surface, measure the springs from the inside of one hook to the inside of the other hook. See the chart below for the recom-mended spring set--up length for your attachment. Loosen or tighten eyebolt as required to obtain the required distance.

Loader Mounted Front Blade Spring Set-Up Length AF11E 72” ........................................... 15” AF11E 84” ........................................... 15” AF11D 84” ..........................................14.2” AF11G 84” ...........................................14.2” AF11D 96” ..........................................14.4” AF11G 96” ..........................................14.4” AF12D 96” ..........................................14.4” AF12G 96” ...........................................14.4” AF12D 108” .........................................14.6” AF12G 108” .........................................14.6” AF12D 120” .........................................14.8” AF12G 120” .........................................14.8”

Springs may be adjusted tighter if desired but do not exceed 16.25” for the AF11E 72” and the AF11E 84” Blades or 15.12” for all other Blades.

AS11 SERIES TRIP EDGE SNOW PUSH With the snow push properly attached to the loader and parked on a hard level surface, mea-sure the springs from the inside of one hook to the inside of the other hook. See the chart below for the recommended spring set--up length for your attachment. Loosen or tighten eyebolt as required to obtain the required distance.

Trip Edge Snow Push Spring Set-Up Length AS11E 96” ..........................................14.4” AS11E 108” ..........................................14.6” AS11E 120” ..........................................14.8”

Springs may be adjusted tighter if desired but do not exceed 15.12”.

OPTIONS Installation of the optional pull back kits, rubber edges, wear edges, toothbars and etc. can be found in the operation section of each attachment.

ATTACHING AND DETACHING EQUIPMENT (200/300/400/500 SERIES LOADERS)NOTE: Procedure is the same for all attachments. Bucket attachment shown.

1. Start tractor engine.

2. Release parking brake and/or place transmission in NEUTRAL.

3. Roll attachment back slightly and raise boom approximately 18” (460 mm) above ground level.

4. Engage tractor parking brake and/or place transmission in PARK. Shut off tractor engine and remove key.

5. Disconnect hydraulic couplers to attach-ment (if so equipped).

6. Remove the quick-lock pin (A) from each side of attachment.

7. Store pins in their storage position (B).8. Start tractor engine.9. Extend bucket cylinders until pin (F)

releases from the holder strap (E) on each side of the attachment.

10. Lower loader boom. Place transmission in REVERSE and move away from the attachment. Holder (D) will release from hook (C) on each side of the attach-ment.

11. Set the parking brake and/or place transmission in PARK. 12. Shut off tractor engine and remove the key.13. Attach equipment in reverse order of detaching.

NOTE: On attachments with two pins (F), the 200,300 and 400 series loaders will utilize the upper pin and the 500 series loader will utilize the lower pin.

AB

CD

E

F

76312 1110 76312

NOTE: Loader with Quik-Change latch plates: Pins/handles on attachment DO NOT need to be in the UP position.

4. Start tractor and slowly extend attachment cylinders until front of attachment touches ground.

5. 600/700 - Lower loader until the holder clears the pockets and pins (B).

800 - Lower loader until bar (C) clears hooks (D) and back up.

6. Shut off the engine, and disconnect hy-draulic hoses.

6. Drive the tractor in reverse until it is clear of the attachment.

NOTE: Latch pins automatically drop on 800 series loaders to prepare the loader for the next attachment.

INSTALLATION

700 SERIES SHOWN

800 SERIES SHOWN

800 SERIES SHOWN

A

B

D C

ATTACHING EQUIPMENT (GLOBAL CARRIER SERIES LOADERS)

NOTE: Latch automatically closes on global carrier.

1. To prepare the loader for attachment, pull and rotate handle to open latch (A).

2. Extend attachment cylinders to angle at-taching brackets forward.

3. Drive forward, adjusting loader height and position until the bar (B) is under hooks (C) and tabs (D) are on the center side of the hooks.

4. Raise loader and retract attachment cylin-ders until latch closes.

B

A

A

ATTACHING EQUIPMENT (600 & 700 SERIES LOADERS WITH QUIK-CHANGE LATCHES AND 800 SERIES LOADERS)

NOTE: Latch pins automatically drop on 800 series loaders to prepare the loader for attach-ment.

1. Extend attachment cylinders to angle at-taching brackets forward.

2. 600/700 - Drive forward, adjusting loader height and position until the top of the brack-et is aligned with the pins (A).

800 - Drive forward, adjusting loader height and position until the bar is under hooks (B) and tabs (C) are on the center side of hooks.

3. Raise loader to engage hooks and retract attachment cylinders quickly.

4. 600/700 - Raise loader until you can check that pins (D) on both sides have fully dropped.

800 - Raise loader until latch pins (E) are visible. Pins on both sides must extend through the attachment latch brackets.

CAUTION! ALWAYS CHECK LATCH PINS BEFORE TILTING OR OPERATING ANY ATTACHMENT.

5. Lower attachment, shut off engine, and connect hydraulic hoses (if equipped) to the auxiliary hydraulic hook up on your loader.

Installation is now complete.

700 SERIES

800 SERIES

700 SERIES BOLT-ON LATCH

SHOWN

C B

D

E

800 SERIES

DETACHING EQUIPMENTNOTE: Disconnect hydraulic attachments before backing away.1. Level attachment approximately 6 inches (150mm) off the ground.

2. Place transmission in PARK and shut off engine.

3. Lift and rotate latches (A) up on both sides of attachment.

A

INSTALLATION

76312 1312 76312

CAUTION! ALWAYS CHECK LATCH PINS BEFORE TILTING OR OPERATING ANY ATTACH-MENT.

5. Lower attachment, shut off engine, and connect hydraulic hoses (if equipped) to the auxiliary hy-draulic hook up on your loader.

Installation is now complete

DETACHING EQUIPMENT(GLOBAL CARRIER SERIES LOADERS)NOTE: Disconnect hydraulic attachments before

backing away.

1. Level attachment approximately 6 inches (150 mm) off the ground.

2. Place transmission in PARK and shut off engine.

3. Pull and rotate handle to open latch (A).

4. Start tractor and slowly extend attachment cylin-ders until front of attachment touches the ground.

5. Lower loader until the bar clears hooks and back up.

6. Shut off the engine and disconnect hydraulic hoses.

7. Drive the tractor in reverse until it is clear of the attachment.

INSTALLATIONB

CD

A

Read all Safety Precautions before operating your new attachment.Refer to your machines operator’s manual for attachment operation.

The silage defacer was designed to loosen haylage and silage from a tightly compacted bunker. It maintains a smooth, compacted bunker face for reduced spoil and the open design allows the operator to see the bunker face and the surrounding work area. There are guides on the end of each arm to limit the depth of each cut. The guides can be easily adjusted by loosening the bolts and sliding the guide in or out until the desired cutting depth is reached. The Model AG10A is compatible with the 800 series loader, the AG10D can be mounted onto 600/700 series loaders and AG10G is compatible with the Global Carrier Series loaders.

SILAGE DEFACER OPERATIONAG10 SERIES SILAGE DEFACER

PROPER OPERATION(1”-3” MATERIAL PER PASS)

IMPROPER OPERATION

1. Clear the area of all bystander and engage the defacer only from the operator’s station.

2. Position the defacer at the top of the bunker and en-gage the auxiliary hydraulics. When the defacer has reached full speed slowly lower into the silage at the desired cutting depth. Do not deface more than 1”-3” of material on each pass, depending on the material.

3. Keep defacer level while it is lowering to help maintain an even cut.

4. Repeat steps #1 through #3 until the desired amount of silage has been obtained.

Operating Tips: For best results do not force the defacer down through the material but allow gravity and the removal of material to determine the downward speed.

To prevent attachment and property damage, avoid direct contact of tines with bunker wallsandfloor. Due to silage piling up on the ground, to obtain a clean cut of the entire bunker face, you maywishtofirstcutthebottom4ft.andthenrepositionthedefaceratthetopandfinishthedownward cut. A 2” depth of cut is recommended to avoid stalling and obtain a clean face.

DANGER! ROTATING HAZARD! To prevent serious injury or death: Clear area of all bystanders. Operate the attachment only when properly seated at the operator’s station.

Before exiting the prime mover, lower the defacer to the ground, turn off the prime mover’s engine, remove the key and apply the brakes.

Do not leave operator’s station until all movement has stopped. • Do not detach loader from tractor with this attachment installed. Equip loader with

materials bucket when detaching.

76312 1514 76312

FREE STALL SCRAPER OPERATIONAE11 SERIES FREE STALL SCRAPERS


Thefreestallscraperwasdesignedtopushlooseand/orfluidmaterialonarelativelysmoothsurface.Itisnotabulldozerandshouldnotbeusedtopushrigidobjectsormaterials. Always try to keep the backplate perpendicular to the ground to avoid excessive wear on the bottom surface of the ends of the rubber edge.

REPLACING THE RUBBER EDGE As the rubber edge wears down to approximately 1/8” exposed, the rubber edge should be inverted or replaced.1. Loosen all nuts and remove the clamp plate(s). 2. Removetherubberedgeandeitherflipovertoutilizethesecondedgeorreplacewitha

new rubber edge if both of the original edges are worn or damaged. 3. Replacetheclampplate(s)tightenallnutstoasnugfittomakesurethattheclamp

plates and rubber edge are properly seated. Torque to 75 ft. lbs. Begin by tightening the nuts in the center section and then the wing sections.

OPTIONAL PULL BACK ASSEMBLY INSTALLATION Installing the optional pull back assembly will allow you to rotate the free stall scraper forward and move material away from a wall or obstacle. The pull back assembly does not need to be removed to obtain maximum production of the free stall scraper. Before installing the pull back assembly onto your free stall scraper, park the tractor on a level surface with the free stall scraper securely attached. Lower the attachment to the ground, turn off the engine, remove the key and apply the brakes.1. Install the rubber edge to the pull back frame using the required clamp plates, the 2-1/2”

longboltsand1/2”flatwashers,lockwashersandhexnutsprovided.Torqueto75ft.lbs.

2. Position the pull back frame onto the top of the free stall scraper aligning the side and back mounting holes. Secure in place using the six 1-1/2” long bolts and the remaining 1/2”flatwashers,lockwashersandhexnutsprovided.Torquetospecification.

Operate the attachment only when properly seated at the operator’s station. Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle.Before exiting the prime mover, lower the free stall scraper to the ground, turn off the prime mover’s engine, remove the key and apply the brakes.Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching.


The loader mounted front blades were designed for snow removal, spreading, leveling or pushinglightmaterialaswellaslightbulldozing.NOTICE: The AF11 Series “Standard Duty” blades are for use on 22 to 95 HP tractors

and are NOT to be mounted onto 7000 series tractors. The horsepower and overall vehicle weight of the 7000 series tractors will exceed the working capacity of the blade.

The AF12 Series “Heavy Duty” blades are for use on 70 to 170 HP tractors and can to be mounted onto 6000 and 7000 series tractors.

Before operating the springs should be checked for the proper tensioning. See Loader Mounted Front Blade Set-Up.

SNOW REMOVAL:If using the loader mounted front blade for snow removal, inspect the site where it is to be used prior to any snowfall. Locate any obstructions (i.e. curbs, sidewalks, pipes, shrubs, fences etc.) and any variations in elevation (i.e. retaining walls, slopes, holes, etc.) so that these elements can be avoided during the snow plowing operation. Do not exceed 15 MPH during operation or lift this attachment above the operator’s eye level or to a height were visibility is obstructed. NOTE: There is a rubber edge available through your John Deere dealer for obtaining a cleaner path on irregular surfaces and also to help protect decorative surfaces such as walkways and patio’s.

SPREADING, LEVELING OR MOVING LIGHT MATERIAL:If using the loader mounted front blade for spreading, leveling or moving light material and ma-nure. Locate any obstructions (i.e. curbs, sidewalks, pipes, shrubs, fences etc.) and any varia-tions in elevation (i.e. retaining walls, slopes, holes, etc.) so that these elements can be avoided during blade operation.NOTE: There is a rubber edge available through your John Deere dealer for scraping live-stock floors or moving light material on a hard, smooth surface.

BULLDOZING:WhenusingtheAF11seriesbladesfordozinglight,loosematerials,thespringsandeyeboltsmust be removed and the long eyebolts installed in the same location. Do not use the blade for dozingofundisturbedsoilorheavymaterials.Damagetotheunitcanoccur.NOTE: When using the AF11 for dozing light, loose materials, the springs and eyebolts must be removed and replaced with the long eyebolts.NOTICE: Dozing undisturbed soil or heavy material can result in damage to this at-

tachment.

HYDRAULIC ANGLE KIT - AF11E 72” & 84”ONLY Before installing the hydraulic angle kit to your AF11E 72” or 84” loader mounted front blade, park the tractor on a level surface with the blade properly attached. Lower the attach-ment to the ground, turn off the engine, remove the key and apply the brakes.

LOADER MOUNTED FRONT BLADE OPERATIONAF11 & AF12 SERIES LOADER MOUNTED FRONT BLADE

76312 1716 76312


1. Remove the positioning tubes from both sides of the blade attachment by removing four pins 5FPRHW8227.

2. Install two straight connectors 5MP30208 into the ports of both cylinders and then install the cylinders in the same location as the positioning tubes using the existing pins, ma-chinery bushings and cotter pins. (Install the cylinders with the rod end of the cylinder towards the blade and barrel end of the cylinder towards the tractor.)

3. Install hose gasket 5FPLAF1421 into the rear frame and route the 6FFS end of both hoses down through the rear frame and connect to the straight connectors on the cylin-ders.

4. Install the couplers to the end of the hydraulic hoses if using the 1/4” body couplers and install straight connectors 5MP3338 to the ends of the hoses followed by the couplers if using the 1/2” body couplers.

5. Cycle the hydraulic cylinders several times to purge all air from the system. Your hy-draulic angle kit is ready for operation.

INSTALLATION OF RUBBER EDGE1. Park the tractor on a hard level surface with the blade properly attached.2. Securely block up the blade so the wear edge is approximately 6”-8” above the ground

and turn off the engine, remove the key and apply the brakes.3. Loosen the nuts on all the wear edge bolts and remove all nuts and bolts except the

bolts on each end of the wear edge.4. While holding up the end of the wear edge, remove the nut and bolt from that end and

allow it to pivot down to the ground.

HOSE ROUTING

HOSEGASKET

HOSES

CYLINDER

COUPLERS

STRAIGHT CONNECTOR 5MP30208

STRAIGHT CONNECTOR 5MP3338(USE WITH 1/2” BODY COUPLERS ONLY)

REAR FRAME

5. Repeat step #4 for the other end of the wear edge. 6. Store the wear edge in a dry location and in such a fashion as to prevent it from inad-

vertently falling and causing injury. Keep the bolts and nuts in a safe location for re-in-stalling when required.

7. Insert the bolts provided with the rubber edge through the clamp plate, the rubber edge and the base of the moldboard on the blade. Loosely secure the bolts with the lock nuts provided. Tighten bolts to 75 ft. lbs.

OPTIONAL RUBBER FLAP ASSEMBLY INSTALLATION Theoptionaltoprubberflapassemblyisdesignedtoreducesnowspillage.1. Park the tractor on a hard level surface with the blade properly attached.2. Place the rubber edge across the top of the blade and secure in place with the clamp

plate(s) required and the 5/16” bolts and lock nuts provided. Torque to 12 ft. lbs. Begin by tightening the nuts in the center and then move towards the outside.

Operate the attachment only when properly seated at the operator’s station. Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle.

Avoid side slope travel whenever possible. Before exiting the prime mover, lower the blade to the ground, turn off the

prime mover’s engine, remove the key and apply the brakes.Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching.


76312 1918 76312

SNOW PUSH OPERATIONAS10 & AS11 SERIES SNOW PUSH


The AS10 and AS11 Series snow push was designed to move large volumes of snow ef-ficiently.Itcanalsobeusedforwastewater,manure,feedlotandfoodcleanup. The snow push removes even the heaviest snow without leaving windrows and the op-tional pull back assembly that is available on the AS11 Series allows you to get next to fences and buildings to pull snow away cleanly. The AS10 Series with the rubber edge is ideal for getting a cleaner surface when using for waste water, manure, feed lot and food cleanup. The AS11 Series with cutting edge trip system allows you to glide over manholes and curb obstructions without loosing gathered material.

REPLACING THE RUBBER EDGE As the rubber edge wears down to approximately 1/8”, the rubber edge should be in-verted or replaced.1. Loosen all nuts and remove the clamp plate(s). 2. Removetherubberedgeandeitherflipovertoutilizethesecondedgeorreplacewitha


plates and rubber edge are properly seated. Torque to 75 ft. lbs. Begin by tightening the nuts from the center to the outside sections.

OPTIONAL PULL BACK ASSEMBLY INSTALLATION Installing the optional pull back assembly on the AF12 Series snow push will allow you to rotate the snow push forward and move snow or other material away from fences and build-ings for a cleaner lot. Before installing the pull back assembly onto your snow push, park the tractor on a level surface with the snow push securely attached. Lower the attachment to the ground, turn off the engine, remove the key and apply the brakes.1. Install the optional rubber edge to the pull back frame using the required clamp plates,

the2-1/2”longboltsand1/2”flatwashers,andlocknutsprovided.Torqueto75ft.lbs.2. Position the pull back frame onto the top of the free stall scraper aligning the side and

backmountingholes.Secureinplaceusingeight1-3/4”longbolts,1/2”flatwashers,lockwashersandhexnutsprovided.Torquetospecification.

3. Position the pull back side shoes onto each side of the snow push and secure in place withtheremainingsix1-3/4”longbolts,1/2”flatwashers,lockwashersandhexnutsprovided.Torquetospecification.


The small square bale fork was designed to handle eight (8) small square bales at a time(flatoronsides).Duetothedifferenceinbalesizesthereisanadjustablebarontheleftside of the attachment to assist you in positioning the attachment over the CENTER of the bales. The Model AB16A is compatible with the 800 series loader, the AB16D can be mounted on the 600/700 series loader and AB16G is compatible with the Global Carrier Series loaders.

1. With the cylinder retracted (tines in the UP position) and the side bar adjusted for the sizeofbales,centerthebaleforkoverthebalesandlowerattachment.Movethetractorslightly forward and to the right to position the bales against the frame and the left side bar.

2. After the bale fork is in place, verify that the tines will securely “grab” all bales. Activate the cylinder which will rotate the tines into the bales.

3. Raise the bale fork just high enough to provide ground clearance. NOTE: If bale ap-pears to be unstable, lower the bale, remove the spears and repeat steps 1 & 2 until the bale is secure. Stop and start loader gradually when lowering or lifting loads.

Operate the attachment only when properly seated at the operator’s station. Do not handle bales that exceed the lift capacity of your loader. See loader specifications.Be sure stack and load heights do not exceed the lifting capabilities of your loader.Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle.

Carry bales as close to the ground as possible. Carry bales parallel to the ground to avoid obstructing your vision.

Never lift more bales than your attachment was design for. Do not stack bales on uneven ground. Bales stacked on uneven ground can topple.Before exiting the prime mover, lower the bale fork to the ground, turn off the prime mover’s engine, remove the key and apply the brakes.Park and store this attachment with the tines pointed down.Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching.

IMPORTANT! If your hydraulically operated attachment starts to drift due to oil leakage within the cylinder assembly, discontinue use until the problem has been corrected.

SMALL SQUARE BALE FORK OPERATIONAB16 SERIES SMALL SQUARE BALE FORK

76312 2120 76312

BALE HUGGER OPERATIONAH11 SERIES BALE HUGGER


Thebalehuggerisdesignedtohandlesingleroundbalesonly.Duetothedifferentsizeroundbales, check the hugger for proper clamping force on your bales before moving or lifting. NOTE:Whenhandlingbalesforthefirsttime,raisethebale6”in.(150mm)abovethegroundandcheck the hugger’s grasp on the bale. Make sure the hugger is not allowing the bale to slip or damaging the plastic wrap. The Model AH11A is compatible with the 800 series loader, the AH11D can be mounted on the 600/700 series loader and AH11G is compatible with the Global Carrier Series loaders.

CAUTION! Do not operate the bale hugger if the roll back guard is not present.

1. Approach the bale with the hugger open and the arms either straight out or rotated straight down. NOTE: The straight down position is typically used to rotate a bale for stacking on end.

2. Position the arms around the middle of the bale while making sure the roll back guard is extend-ed past the bale.

3. Close the arms, raise and roll back bale approximately 20° or just high enough to provide ground clearance. NOTE: If bale appears to be unstable, lower the bale, and repeat steps 1 & 2 until the bale is secure. Stop and start loader gradually when lowering or lifting loads.

Operate the attachment only when properly seated at the operator’s station. Do not handle bales that exceed the lift capacity of your loader. See loader specifi-cations.Be sure stack and load heights do not exceed the lifting capabilities of your load-er.Reduce speed when driving over rough terrain, on a slope, or turning, to avoid overturning the vehicle.

When handling bales on a slope, avoid side slope travel whenever possible. Drive up the slope to pick up a bale and then down in reverse.

Carry bales as close to the ground as possible. Never try to stop a rolling bale with the tractor or loader.

Never lift more bales than your attachment was design for. Do not stack bales on uneven ground. Bales stacked on uneven ground can topple.Before exiting the prime mover, lower the bale hugger to the ground, turn off the prime mover’s engine, remove the key and apply the brakes.Do not detach loader from tractor with this attachment installed. Equip loader with materials bucket when detaching.

IMPORTANT! If your hydraulically operated attachment starts to drift due to oil leakage within the cylinder assembly, discontinue use until the problem has been corrected.

ROLL BACK GUARD

BALE HUGGER

MAINTENANCE

GENERAL INFORMATION Your attachment was designed to be virtually maintenance free. Very little effort is needed to keep it in top condition. It is, however, important to follow these procedures to get full performance and longevity out of the equipment.

IMPORTANT: When replacing parts, use only factory approved replacement parts. Manufac-turer will not claim responsibility for use of unapproved parts or accessories and/or other damages as a result of their use.

LUBRICATION The only lubrication your attachment may need is the greasing of the cylinder ends and mostpivotpoints.Agreasefittinghasbeeninstalledtofacilitatethistask.Followingisalistofeachoftheattachmentsinthismanualthatrequirelubricatingandthenumberofgreasefittings.Werec-ommendgreasingallgreasefittingsaftertheinitial8hoursofoperationandthenevery40hoursofoperation thereafter.AF11E Series Loader Mounted Front Blades = 4 (Onefittingoneachanglebracket/moldboadpivotpin

and one on loader attachment plate at pivot point.)AF11D & AF11G Series Loader Mounted Front Blades = 1 (Onefittingonloaderattachmentplateatpivot

point.)AF12D & AF12G Series Loader Mounted Front Blades = 6 (Onefittingoneachcylinderendandtwoon

loader attachment plate at pivot point.)AB16 Series Small Bale Fork = 18 (Cylinderendsandonefittingoneachtinemountingtube.)AH11A & AH11D Bale Hugger = 2 (Onefittingoneacharmwheretheypivotinthemountingframe.)AH11G Bale Hugger = 4 (Cylinderendsandonefittingoneacharmwheretheypivotinthemountingframe.)AG10 Series Silage Defacer = 2 (Onefittingoneachflangetteandbearingset.)

DAILY OR EVERY 8 HOURS OF OPERATION Replace any missing bolts or nuts with approved replacement parts. Check hydraulic system for leaks. (If so equipped.) See procedure below. Visually inspect the machine for worn parts or cracked welds. Repair as necessary. Replace any damaged, illegible or missing decals. SeeDecalIdentificationandReplacement

CARDBOARD

HYDRAULIC HOSE OR FITTING

MAGNIFYING GLASS

WARNING! Escaping fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Fluid escaping from a very small hole can be almost invisible. Use a piece of cardboard or wood, rather than hands to search for suspected leaks.

Keep unprotected body parts, such as face, eyes, and arms as far away as possible from a suspected leak. Flesh injected with hydraulic fluid may develop gan-grene or other permanent disabilities.

If injured by injected fluid, see a doctor at once. If your doctor is not familiar with this type of injury, ask him or her to research it immediately to determine proper treatment.

76312 2322 76312

DECAL IDENTIFICATION AND REPLACEMENT Decalplacementandidentificationforalloftheattachmentscanbefoundonthepartsdia-gramsandlistslocatedatthebackofthismanual.Thedecalsareidentifiedbytheirpartnumberswith reductions of the actual decals located on the page. Use this information to order replace-ments for missing, illegible or damaged deals. When replacing parts with safety signs attached, the safety sign must also be replaced. All Safety Decals are free of charge. Contact your local Frontier dealer for replacements.

REPLACING SAFETY SIGNS:1. Cleantheareaofapplicationwithnonflammablesolvent.2. Wash the same area with soap and water and then allow the surface to fully dry.3. Remove the backing from the safety sign exposing the adhesive surface.4. Apply the safety sign to location shown in the parts diagram and smooth out bubbles.Helpful Hints: (1) Decals adhere to a warm surface better than a cold surface. (2) Apply-ing heat (from a hair dryer) will greatly improve your ability to remove a damaged decal before preparing the surface for installation of a new one.

MONTHLY OR EVERY 40 HOURS OF OPERATION Check all bolts, nuts and bearings for tightness. Tighten or replace as needed. Clean equipment of dirt, oil, grease, etc. This will assist you in making a visual inspection and help avoid overlooking worn or damaged components. Adjust and lubricate the drive chain on the AG10 Series silage defacer. (See Chain Ad-justment.) To lubricate the drive chain: Remove the top chain cover and spray a chain lubri-cant along the top of the upper and lower portion of the drive chain.

WARNING! DO NOT OPERATE THE DEFACER DURING ANY MAINTENANCE OR WHILE THE TOP CHAIN COVER IS REMOVED.

Adjust the shoe weldments on the silage defacer so material is removed but the shoe is never less than 1/2” shorter than the blades.

CHAIN ADJUSTMENT ON AG10 SERIES SILAGE DEFACER We recommend adjusting the chain on the silage defacer after the initial 4 hours and then monthly thereafter. To Adjust Chain: Remove the top chain cover and loosen the two bolts on the motor mounting plate and the one bolt on the cam lock. Insert a 1/2” ratchet into the cam lock and rotate until the chain is tight. (A properly adjusted chain will have a minimal amountofchaindeflection.Overtensioningwillcauseprematurewear.)NOTE: If all of the cam lock adjustment is used and the chain and sprocket are still serviceable, you can remove a “half link” from the chain at the master link location.

MAINTENANCE

REPLACEMENT OF WEAR EDGE ON LOADER MOUNTED FRONT BLADES1. Park the tractor on a hard level surface with the blade properly attached.2. Securely block up the blade so the wear edge is approximately 6”-8” above the ground

and turn off the engine, remove the key and apply the brakes.3. Loosen the nuts on all the wear edge bolts and remove all nuts and bolts except the

bolts on each end of the wear edge.4. While holding up the end of the wear edge, remove the nut and bolt from that end and

allow it to pivot down to the ground.5. Repeat step #4 for the other end of the wear edge. The wear edges are reversible and

maybeflippedtop-to-bottomforreinstallation.Whenbothsideshavebeenworn,prop-erly dispose of the wear edge and all bolts and nuts.

6. Install the new wear edge by reversing the above procedure. Tighten bolts to 75 ft. lbs.

REPLACEMENT OF OPTIONAL RUBBER EDGE ON LOADER MOUNTED FRONT BLADE As the rubber edge wears down to approximately 1/8” exposed, the rubber edge should be inverted or replaced.1. Park the tractor on a hard level surface with the blade properly attached.2. Securely block up the blade so the rubber edge is approximately 6”-8” above the ground

and turn off the engine, remove the key and apply the brakes.3. Loosen all nuts and remove the clamp plate(s). 4. Removetherubberedgeandeitherflipovertoutilizethesecondedgeorreplacewitha

new rubber edge if both of the original edges are worn or damaged.

NOTE: Position the rubber edge so that no more than 1” of the edge extends below the lowest point of the moldboard on the AF11 Series and no more than 1-1/2” on the AF12 Series.

5. Replacetheclampplate(s)tightenallnutstoasnugfittomakesurethattheclampplates and rubber edge are properly seated. Torque to 75 ft. lbs. on the AF11E 72” and 84” and 150 ft. lbs on all other blades. Begin by tightening the nuts in the center and move to the outside edges.

MAINTENANCE

BLADE REPLACEMENT ON AG10 SERIES SI-LAGE DEFACER It is important to align the blades on the silage defacerrotorinsuchafashionthatminimizesthetorquegenerated by the blades contacting the haylage or silage pile.

ADJUST THE BLADES ON THE ROTOR SO THAT THE BLADE TIPS DO NOT CONTACT THE MATERIAL AT THE SAME TIME.

76312 2524 76312

REPLACEMENT OF THE RUBBER EDGE ON FREE STALL SCRAPERS As the rubber edge wears down to approximately 1/8” exposed, the rubber edge should be inverted or replaced.

1. Park the tractor on a hard level surface with the free stall scraper properly attached.2. Securely block up the scraper so the rubber edge is approximately 6”-8” above the

ground and turn off the engine, remove the key and apply the brakes.3. Loosen all nuts and remove the clamp plate(s). 4. Removetherubberedgeandeitherflipovertoutilizethesecondedgeorreplacewitha


plates and rubber edge are properly seated. Torque to 75 ft. lbs. Begin by tightening the nuts in the center section and then the wing sections.

REPLACEMENT OF RUBBER EDGE ON PULL BACK ASSEMBLIES As the rubber edge on the pull back assemblies (snow push and free stall scrapers) wears down it should be inverted or replaced.1. Park the tractor on a hard level surface with the attachment properly attached.2. Turn off the engine, remove the key and apply the brakes.3. Loosen all nuts and remove the clamp plate(s). 4. Removetherubberedgeandeitherflipovertoutilizethesecondedgeorreplacewitha


plates and rubber edge are properly seated. Torque to 75 ft. lbs.

MAINTENANCE

WARNING! Disconnect cylinder carefully from hydraulic hoses after removal from at-tachment. Hydraulic oil under pressure can cause severe injury or death.

CYLINDER SEAL REPLACEMENT The following information is provided to assist you in the event you should need to repair or rebuild a hy-draulic cylinder. When working on hydraulic cylinders, make sure that the work area and tools are clean and free of dirt to prevent contamination of the hydraulic system and damage to the hydraulic cylinders. Always protect the active part of the cylinder rod (the chrome section). Nicks or scratches on the surface of the rod could result in cylinder failure. Clean all parts thoroughly with a cleaning solvent before reassembly.

DISASSEMBLY PROCEDUREIMPORTANT: Do not contact the active surface of the cylinder rod with the vise. Damage to the rod could result.THREADED TYPE GLAND 1. Rotate the gland with a spanner wrench counterclockwise until the gland is free of the cylinder tube.2. Pull the cylinder rod from the cylinder tube and inspect the piston and the bore of the cylinder tube for

deep scratches or galling. If damaged, the piston AND the cylinder tube must be replaced.

3. Removethehexnut,piston,flatwasherorspacertube(ifsoequipped),andglandfromthecylinderrod.Ifthe cylinder rod is rusty, scratched, or bent, it must be replaced.

4. Remove and discard all the old seals.

ASSEMBLY PROCEDUREIMPORTANT: Replace all seals even if they do not appear to be damaged. Failure to replace all seals may result in premature cylinder failure. NOTE: Seal kits will service most cylinders of similar bore size and rod diameter.1. Installthecylinderrodsealintheglandfirst.Becarefulnottodamagethesealintheprocess,asitis

somewhatdifficulttoinstall.

NOTE:Aspecialinstallationtool(Part#5MP65349)isavailabletohelpwithinstallingtheseal.Simplyfittheendof the tool over the seal so that the large prong of the tool is on the outside of the seal, and the two smaller prongs on the inside. The lip of the seal should be facing towards the tool. Rotate the handles on the tool around to wrap the seal around the end of the tool.

Rotate the handles on the tool around to wrap the seal around the end of the tool.

MAINTENANCE

76312 2726 76312

Now insert the seal into the gland from the inner end. Position the seal in its groove, and release and remove the tool. Press the seal into its seat the rest of the way by hand.

2. Install the new piston ring, rod wiper, O-rings and backup washers, if ap-plicable, on the piston.

Be careful not to damage the seals. Caution must be used when installing the piston ring. The ring must be stretched carefully over the piston with a smooth, round, pointed tool.

3. After installing the rod seal inside the gland, as shown in step #1, install the external seal.

NOTE: Threaded glands may have been equipped with a separate O-ring and backup washer system or a polypak (all in one) type seal. Current seal kits con-tain a polypak (all in one) type seal to replace the discarded seal types on ALL THREADED GLANDS.

4. Slide the gland onto the cylinder rod, being careful not to damage the rod wiper.Theninstallthespacer,orflatwasher(ifsoequipped),smallo-ring,piston, and hex nut onto the end of the cylinder rod.

5. Secure the cylinder rod (mounting end) in a vise with a support at its center. Torque the nut to the amount shown for the thread diameter of the cylinder rod (see chart).

Thread Diameter POUNDS - FEET 7/8" 150-200 *1" 230-325 1-1/8" 350-480 1-1/4" 490-670 1-3/8" 670-900

* 1" Thread Diameter WITH 1.25" Rod Diameter Min. 230 ft. lbs. Max. 250 ft. lbs.

IMPORTANT: Do not contact the active surface of the cylinder rod with thevise. Damage to the rod could result.

6. Applyalubricant(suchasLubriplate#105)tothepistonandteflonring.Insertthecylinderrodassemblyinto the cylinder tube.

IMPORTANT: Ensure that the piston ring fits squarely into the cylinder tube and piston groove, otherwise the ring may be damaged and a leak will occur.

7. Use a spanner wrench to rotate the gland clockwise into the cylinder. Continue to rotate the gland with the spanner wrench until it is tight.

WARNING! Cylinders serviced in the field are to be tested for leakage prior to the attachment being placed in work. Failure to test rebuilt cylinders could result in damage to the cylinder and/or the attachment, cause severe personal injury or even death.

MAINTENANCE

SMALL SQUARE BALE FORK AND BALE HUGGER SPECIFICATIONSModel Compatibility AB16A AB16D AB16G AH11A AH11D AH11GOverall Height (inches) 31 31 31 50 50 49Overall Width (inches) 80 80 80 57 57 56Overall Length (inches) 90 90 90 60 60 78Attachment Weight (lbs.) 1090 1090 1090 725 725 785Shipping Weight (lbs.) 1190 1190 1190 825 825 885Bale Handling Capacity 8 Flat/10 Index 8 Flat/10 Index 8 Flat/10 Index 3’-6’ Round 3’-6’ Round 3’-6’ Round Sm. Square Sm. Square Sm. Square Wrapped Wrapped Wrapped

SPECIFICATIONS

SILAGE DEFACER SPECIFICATIONS AG10A AG10D AG10GOverall Height (inches) 24 24 24Overall Width (inches) 96 96 96Overall Length (inches) 55.50 55.50 55.50Cutting Width (inches) 96 96 96Attachment Weight (lbs.) 735 735 735Shipping Weight (lbs.) 870 870 870

AF11 SERIES LOADER MOUNTED FRONT BLADES - Standard Duty (22 to 95 HP)Model Compatibility & Size AF11E - 72” AF11E - 84” AF11D - 84” AF11G - 84” AF11D - 96” AF11G - 96”Overall Height (inches) 23.2 23.2 32 32 32 32Overall Width (inches) 71.75 83.8 84 84 96 96Overall Length (inches) 34.8 34.8 48 48 48 48Angle (Left and Right) 30° 30° 30° 30° 30° 30°Cutting Width @ 30° Angle (inches) 62 73 73 73 83 83Attachment Weight (lbs.) 400 450 730 710 800 780Shipping Weight (lbs.) 430 480 780 760 850 830

AS10 & AS11 SERIES SNOW PUSHModel Compatibility & Size AS10H - 72” AS10H - 84” AS10H - 96” AS11E - 96” AS11E - 108” AS11E - 120”Overall Height (inches) 30.75 30.75 30.75 39.8 39.8 39.8Overall Width (inches) 74.25 86.25 98.25 98.38 110.38 119.88Overall Length (inches) 34 34 34 41.5 41.5 41.5Attachment Weight (lbs.) 440 477 514 900 943 980Shipping Weight (lbs.) 490 527 564 950 993 1030

AE11 SERIES FREE STALL SCRAPERSModel Compatibility & Size AE11E - 60” AE11E - 72” AE11D - 84” AE11E - 96”Overall Height (inches) 28 28 28 28Overall Width (inches) 60 72 84 96Overall Length (inches) 29 29 29 29Attachment Weight (lbs.) 277 313 340 384Shipping Weight (lbs.) 320 355 395 430

LOADER SERIES COMPATIBILITY: A=800 SERIES D=600/700 SERIES E=300/400/500 SERIES F=200/300/400/500SERIES G=GLOBAL CARRIER SERIES H=300/400 SERIES

AF12 SERIES LOADER MOUNTED FRONT BLADES - Heavy Duty (70 to 170 HP)Model Compatibility & Size AF12D - 96” AF12G - 96” AF12D - 108” AF12G - 108” AF12D - 120” AF12G - 120”Overall Height (inches) 32 32 32 32 32 32Overall Width (inches) 96 96 108 108 120 120Overall Length (inches) 54 54 54 55 56 57Angle (Left and Right) 35° 35° 35° 35° 35° 35°Cutting Width @ 35° Angle (inches) 79 79 89 89 99 99Attachment Weight (lbs.) 1195 1175 1265 1245 1360 1310Shipping Weight (lbs.) 1245 1225 1315 1295 1410 1360

76312 2928 76312

BOLT TORQUEBOLT TORQUE SPECIFICATIONS

GENERAL TORQUE SPECIFICATION TABLES Use the following charts when determining bolt torque specifications when special torques are not given. Always use grade 5 or better when replacing bolts.

SAE BOLT TORQUE SPECIFICATIONSNOTE: The following torque values are for use with extreme pressure lubricants, plating or hard washer applications Increase torque 15% when using hardware that is unplated and either dry or lubricated with engine oil.

Bolt SizeSAE GRADE 5 TORQUE SAE GRADE 8 TORQUE

Pounds Feet Newton-Meters Pounds Feet Newton-MetersBolt head identification marks as per grade.

NOTE: Manufacturing Marks Will VaryInches Millimeters UNC UNF UNC UNF UNC UNF UNC UNF

1/4 6.35 8 9 11 12 10 13 14 185/16 7.94 14 19 19 23 20 25 27 343/8 9.53 30 36 41 49 38 46 52 62

7/16 11.11 46 54 62 73 60 71 81 961/2 12.70 68 82 92 111 94 112 127 152

9/16 14.29 94 112 127 152 136 163 184 2215/8 15.88 128 153 174 207 187 224 254 3043/4 19.05 230 275 312 373 323 395 438 5367/8 22.23 340 408 461 553 510 612 691 8301 25.40 493 592 668 803 765 918 1037 1245

1-1/8 25.58 680 748 922 1014 1088 1224 1475 16601-1/4 31.75 952 1054 1291 1429 1547 1700 2097 23051-3/8 34.93 1241 1428 1683 1936 2023 2312 2743 31351-1/2 38.10 1649 1870 2236 2535 2686 3026 3642 4103

METRIC BOLT TORQUE SPECIFICATIONSNOTE: The following torque values are for use with metric hard-ware that is unplated and either dry or lubricated with engine oil. Reduce torque 15% when using hardware that has extreme pressure lubricants, plating or hard washer applications.

Size of Bolt Grade No. Pitch (mm) Pounds Feet Newton-Meters Pitch (mm) Pounds Feet Newton-Meters5.6 3.6-5.8 4.9-7.9 - -

M6 8.8 1.0 5.8-.4 7.9-12.7 - - -10.9 7.2-10 9.8-13.6 - -5.6 7.2-14 9.8-19 12-17 16.3-23

M8 8.8 1.25 17-22 23-29.8 1.0 19-27 25.7-36.610.9 20-26 27.1-35.2 22-31 29.8-425.6 20-25 27.1-33.9 20-29 27.1-39.3

M10 8.8 1.5 34-40 46.1-54.2 1.25 35-47 47.4-63.710.9 38-46 51.5-62.3 40-52 54.2-70.55.6 28-34 37.9-46.1 31-41 42-55.6

M12 8.8 1.75 51-59 69.1-79.9 1.25 56-68 75.9-92.110.9 57-66 77.2-89.4 62-75 84-101.65.6 49-56 66.4-75.9 52-64 70.5-86.7

M14 8.8 2.0 81-93 109.8-126 1.5 90-106 122-143.610.9 96-109 130.1-147.7 107-124 145-1685.6 67-77 90.8-104.3 69-83 93.5-112.5

M16 8.8 2.0 116-130 157.2-176.2 1.5 120-138 162.6-18710.9 129-145 174.8-196.5 140-158 189.7-214.15.6 88-100 119.2-136 100-117 136-158.5

M18 8.8 2.0 150-168 203.3-227.6 1.5 177-199 239.8-269.610.9 175-194 237.1-262.9 202-231 273.7-3135.6 108-130 146.3-176.2 132-150 178.9-203.3

M20 8.8 2.5 186-205 252-277.8 1.5 206-242 279.1-327.910.9 213-249 288.6-337.4 246-289 333.3-391.6

Bolt head identification marks as per grade.

76312 3130 76312

AG10A, AG10D & AG10G SILAGE DEFACER600, 700, 800 & GLOBAL CARRIER SERIES LOADER

DIAGRAM 1 OF 2

34

35 3637 38

39

40

39 35

16

33

39

38 37

1514 39

3834

37 810

53

1

24

11

9

1513

12

5

4

4

5

372

3

36

10

11

31

3230

29 28

28

20

1918

17

27

8

106

7 23 4

5 9

40

40

2122

23

24

25

26

41 42 43

44

4546


LIST 1 OF 2 ITEM REQ’D PART NO. DESCRIPTION

1 2 5MP32916 Blade - Left End 2 15 5MP32920 Blade - Center B 3 15 5MP32919 Blade - Center A 4 4 5MP33617 Blade - Frame Side B 5 4 5MP33616 Blade - Frame Side A 6 2 5MP32917 Blade - Right End 7 42 5MP22324 1/2” UNF x 4-1/2” Hex Bolt - GR8 42 5MP1840 1/2” UNF Lock Nut 8 2 5MP89129 Flangette Set 5MP6616 Replacement Grease Fitting 9 2 5MP89127 Ball Bearing w/Collar 5MP1624 Replacement Set Screw 10 12 5MP1088 1/2” UNC X 1” Hex Bolt - GR5 12 5MP1646 1/2” Hard Flat Washer

11 2 5MP33427 Shoe 12 1 5MP15747 Spacer 5MP1624 3/8” UNC X 5/16” Set Screw 13 1 5MP15751 Bottom Chain Cover 14 1 5MP32849 Top Chain Cover 15 4 5MP1837 3/8” UNC Deformed Lock Nut 4 5MP1514 3/8” Flat Washer 16 1 5MP107267 Silage Defacer Frame - Global Carrier Series Loader 1 5MP111554 Silage Defacer Frame - 600 & 700 Series Loader

1 5MP15448 Silage Defacer Frame - 800 Series Loader 17 1 5MP32895 Center Bar 18 1 5MP32903 Key 19 1 5MP32905 Sprocket - 18 Tooth, No. 80 20 1 5MP32906 Drive Chain, No. 80, 73 Pitches 5MP53298 Replacement Master Link

21 1 5MP1872 1/2” UNC X 1-1/2” Carriage Bolt 1 5MP1790 1/2” UNC Serrated Flange Lock Nut 22 1 5MP32848 Cam Lock 23 1 5MP33249 Sprocket - 10 Tooth, No. 80 24 4 5MP22336 1/2” UNC X 1-1/2” Socket Head Bolt 4 5MP1228 1/2” UNC Hex Nut 25 2 5MP1872 1/2” UNC X 1-1/2” Carriage Bolt 2 5MP1790 1/2” UNC Serrated Flange Lock Nut

76312 3332 76312


DIAGRAM 2 OF 2

34

35 3637 38

39

40

39 35

16

33

39

38 37

1514 39

3834

37 810

53

1

24

11

9

1513

12

5

4

4

5

372

3

36

10

11

31

3230

29 28

28

20

1918

17

27

8

106

7 23 4

5 9

40

40

2122

23

24

25

26

41 42 43

44

4546


LIST 2 OF 2

ITEM REQ’D PART NO. DESCRIPTION

26 1 5MP32847 Motor Mounting Plate 27 1 5MP33200 Motor 5MP5662 Replacement Key 28 2 5MP37976 5/8” Hose X 100” 10MBo-10MBo 29 1 5MP31886 Female Coupler 10FBo 1/2” Body (800 Series Loader Only) 1 5MP15512 Male Coupler 10FBo 1/2” Body (Global Carrier, 600 & 700 Series Loaders Only) 30 1 5MP15512 Male Coupler 10FBo 1/2” Body

31 1 5MP51754 Female Coupler Cover (Use with 5MP31886 Coupler) 32 1 5MP51753 Male Coupler Cover (Use with 5MP15512 Coupler) 33 4 5MP15581 Square Plastic Plug 34 1 5MP40151 Warning Decal, High Pressure Service 35 1 5FP1002423 Warning Decal, Read Manual, No Riders 36 1 -------- SerialNumberIdentificationTagLocation 37 3 5MP4105 Danger Decal, Stand Clear 38 2 5FP5010010 Caution Decal, Do Not Detach Loader 39 3 5MP4235 Danger Decal, Moving Paddles 40 2 5MP40964 Warning Decal, Falling Loads

ITEMS #41 THROUGH #46 ARE USED ON 600 & 700 SERIES LOADERS ONLY

41 4 5MP2560 M12 Hex Nut 42 1 5FP1352136 Right Latch Pin 43 2 5FP0710145 Trip Pin 44 1 5FP1352135 Left Latch Pin 45 2 5MP10195 Roll Pin 46 2 5FP0710144 Compression Spring

76312 3534 76312

AE11E SERIES FREE STALL SCRAPERS300/400/500 SERIES LOADERS

1

2

3

4

5

6

7

8

6

7

8

AE11E SERIES FREE STALL SCRAPERS300/400/500 SERIES LOADERS


1 1 5FP135266506 60” Scraper Frame 1 5FP135258506 72” Scraper Frame 1 5FP135267406 84” Scraper Frame 1 5FP135268306 96” Scraper Frame

2 1 5FP1352668 60” Rubber Edge 1 5FP1352592 72” Rubber Edge 1 5FP1352677 84” Rubber Edge 1 5FP1352686 96” Rubber Edge

3 2 5FP1352609 End Clamp Plate 4 1 5FP1352669 Center Clamp Plate (AE11E - 60” Scraper) 1 5FP1352608 Center Clamp Plate (AE11E - 72” Scraper) 1 5FP1352678 Center Clamp Plate (AE11E - 84” Scraper) 1 5FP1352687 Center Clamp Plate (AE11E - 96” Scraper)

5 Varies 5MP1094 1/2” UNC X 2-1/2” Hex Bolt Varies 5MP1516 1/2” Flat Washer Varies 5MP1505 1/2” Lock Washer Varies 5MP1228 1/2” UNC Hex Nut

6 1 ----- SerialNumberIdentificationTagLocation 7 1 5FPW50426 Warning Decal, Quick Lock Pins 8 1 5FP1002423 Warning Decal, Read Manual, No Riders

76312 3736 76312

OPTIONAL PULLBACK KITAE11E SERIES FREE STALL SCRAPERS

1

2

3

4

8

4

7

6

7

5 65

5

5

OPTIONAL PULLBACK ASSEMBLYAE11E SERIES FREE STALL SCRAPERS

5FP10736 OPTIONAL 60” PULL BACK ASSEMBLY ITEM REQ’D PART NO. DESCRIPTION 1 1 5FP1352670 60” Pull Back Frame 2 1 5FP1352672 60” Rubber Edge 3 1 5FP1352673 60” Clamp Plate 4 6 5MP1090 1/2” UNC X 1-1/2” Hex Bolt 5 24 5MP1516 1/2” Flat Washer

6 12 5MP1505 1/2” Lock Washer 7 12 5MP1228 1/2” UNC Hex Nut 8 6 5MP1094 1/2” UNC X 2-1/2” Hex Bolt







76312 3938 76312

AF11E 72” LOADER MOUNTED FRONT BLADE300, 400 & 500 SERIES LOADERS

1

2

3

3

45

6

7

8

910

3

11

12

1314

15

16 17

18

19

9

21

22

23

20

24

24

27

25 4

26

28

29

30

31

32

33

33

3435

36

3231

3029

28



1 1 5FP1353215 Rear Mount 2 1 5FP1353223 Pivot Pin 3 4 5MP6616 Grease Fitting 4 10 5MP1228 1/2” UNC Hex Nut 5 2 5MP1516 1/2” Flat Washer

6 2 5FPRHW8063 Eyebolt - Short 7 2 5FPDHF2018 Tension Spring 8 2 5FPRHW8062 Eyebolt - Long 9 4 5FPRHW8227 Clevis Pin 10 2 5FP13-51258 Outside Positioning Tube

11 2 5FP0710076 Hitch Pin 2 5FPRHW8075 Replacement Hair Pin (Included with Hitch Pin) 12 2 5FP1351259 Inside Positioning Tube 13 4 5FPRHW5972 Machinery Bushing 14 4 5FPRHW8011 Cotter Pin 15 1 5FP1352265 72” Blade

16 1 5FPLAF1407 72” Wear Edge 17 1 5FP1353214 Pivot Mounting 18 1 5MP1094 1/2” UNC X 2-1/2” Hex Bolt 19 1 5MP1841 1/2” UNC Torque Lock Nut 20 2 5FPRHW1041 1/4” UNC X 2” Hex Bolt

21 2 5MP1629 1/4” UNC Nylock Nut 22 2 5FPLAF9782 Pivot Pin 23 2 5FPRHW8064 Lynch Pin 24 22 5FP0710126 1-5/8” Flat Washer 25 6 5MP1505 1/2” Lock Washer

26 6 5FPRHW2407 1/2” UNC x 2” Carriage Bolt 27 2 5FPLAF1485 Skid Shoe 28 2 5FP1003751A WarningDecal,CrushingandPinchingHazard 29 1 ----- SerialNumberIdentificationTagLocation 30 1 5FP1002423 Warning Decal, Read Manual, No Riders

31 1 5FPW50426 Warning Decal, Lock Pins 32 - 5MP40151 Warning Decal, High Pressure Fluid 33 2 5FP500721 WarningDecal,CrushHazard 34 1 5MP25453 Manual Storage Tube 35 2 5MP1003 1/4” UNC X 1” Hex Bolt

36 2 5MP1629 1/4” UNC Nylock Hex Nut

76312 4140 76312


1

2

3

3

45

6

7

8

910

3

11

12

1314

15

16 17

18

19

9

21

22

23

20

24

24

27

25 4

26

28

29

30

31

32

33

33

3435

36

32313029

28



1 1 5FP1353215 Rear Mount 2 1 5FP1353223 Pivot Pin 3 4 5MP6616 Grease Fitting 4 11 5MP1228 1/2” UNC Hex Nut 5 2 5MP1516 1/2” Flat Washer

6 2 5FPRHW8063 Eyebolt - Short 7 2 5FPDHF2018 Tension Spring 8 2 5FPRHW8062 Eyebolt - Long 9 4 5FPRHW8227 Clevis Pin 10 2 5FP1351258 Outside Positioning Tube

11 2 5FP0710076 Hitch Pin 2 5FPRHW8075 Replacement Hair Pin (Included with Hitch Pin) 12 2 5FP1351259 Inside Positioning Tube 13 4 5FPRHW5972 Machinery Bushing 14 4 5FPRHW8011 Cotter Pin 15 1 5FP1352264 84” Blade

16 1 5FPLAF1408 84” Wear Edge 17 1 5FP1353214 Pivot Mounting 18 1 5MP1094 1/2” UNC X 2-1/2” Hex Bolt 19 1 5MP1841 1/2” UNC Torque Lock Nut 20 2 5FPRHW1041 1/4” UNC X 2” Hex Bolt

21 2 5MP1629 1/4” UNC Nylock Nut 22 2 5FPLAF9782 Pivot Pin 23 2 5FPRHW8064 Lynch Pin 24 22 5FP0710126 1-5/8” Flat Washer 25 7 5MP1505 1/2” Lock Washer

26 7 5FPRHW2407 1/2” UNC x 2” Carriage Bolt 27 2 5FPLAF1485 Skid Shoe 28 2 5FP1003751A WarningDecal,CrushingandPinchingHazard 29 1 ----- SerialNumberIdentificationTagLocation 30 1 5FP1002423 Warning Decal, Read Manual, No Riders

31 1 5FPW50426 Warning Decal, Lock Pins 32 - 5MP40151 Warning Decal, High Pressure Fluid 33 2 5FP500721 WarningDecal,CrushHazard 34 1 5MP25453 Manual Storage Tube 35 2 5MP1003 1/4” UNC X 1” Hex Bolt

36 2 5MP1629 1/4” UNC Nylock Hex Nut

76312 4342 76312

AF11D & AF11G 84” LOADER MOUNTED FRONT BLADE600 & GLOBAL CARRIER SERIES LOADERS

12

3

4

5

6

7

8 9 1011

1213

14

15

161718

19

20

21

22

2324

25

26

9

27

28

2931

32

33

32

3334

34 35

36

37

37

38

3940

33

34

35

36

30

NOTICE: Do not operate the AF11D 84” Loader Mounted Front Blade on 7000 series tractors. The horsepower and overall vehicle weight of the 7000 series tractors will exceed the working capacity of the blade.

ITEM REQ’D PART NO. DESCRIPTION 1 2 5MP17139 Male Coupler 8FBo 1/2” Body 2 2 5MP3338 8MBo-6FBo Straight Connector 3 2 5FP0310125 1/4” Hose X 81” 6FFS-6MBo 4 1 5FPLAF1421 Rubber Hole Gasket 5 2 5FP032115 6MBo-6MFS 45° Elbow 6 2 5FPLAF4563 Cylinder Assembly 7 4 5MP1149 3/4” UNC X 5” Hex Bolt 4 5MP1936 3/4” UNC Torque Lock Nut 8 1 5FPLAF900507 Mounting Frame (600 & 700 Series Loader) 1 5FPLAF900509 Mounting Frame (Global Carrier Series Loader) 9 4 5MP2560 M12 Hex Nut (600 & 700 Series Loader ONLY) 10 1 5FP1352136 Right Latch Pin (600 & 700 Series Loader ONLY)

11 2 5FP0710145 Trip Pin (600 & 700 Series Loader ONLY) 12 2 5MP10195 Roll Pin (600 & 700 Series Loader ONLY) 13 1 5FP1352135 Left Latch Pin (600 & 700 Series Loader ONLY) 14 2 5FP0710144 Compression Spring (600 & 700 Series Loader ONLY) 15 2 5MP1096 1/2” UNC X 3” Hex Bolt 2 5MP1841 1/2” UNC Torque Lock Nut 16 1 5FPLAF9008 Bushing 17 1 5FPRHW5970 Machine Bushing 18 1 5FP1353209 Pivot Pin 19 1 5MP6616 Grease Fitting 20 4 5FPRHW8065 Spade Bolt 8 5MP1517 5/8” Flat Washer 8 5MP1230 5/8” UNC Hex Nut

21 4 5FPLAF6405 Trip Spring 22 1 5FP1353201 Pivot Mounting 23 3 5MP1194 1” UNC X 4-1/2” Hex Bolt 24 3 5MP1541 1” UNC Nylock Nut 25 1 5FPLAF1512 84” Blade 26 1 5FP1351823 84” Wear Edge 27 7 5MP1118 5/8” UNC X 2-1/2” Hex Bolt 7 5MP1506 5/8” Lock Washer 7 5MP1230 5/8” UNC Hex Nut 28 2 5FPRHW8064 Klik Pin 29 40 5FP0710126 1-5/8” SAE Flat Washer 30 2 5FPLAF1485 Skid Shoe

31 2 5FP5010019 AmberReflectingTape2”x9” 32 2 5FP5010018 RedReflectingTape2”x9” 33 2 5FP1003751A WarningDecal,CrushingandPinchingHazard 34 - ----- SerialNumberIdentificationTagLocation 35 1 5FP1002423 Warning Decal, Read Manual, No Riders 36 1 5MP40151 Warning Decal, High Pressure Fluid 37 2 5FP500721 WarningDecal,CrushHazard 38 1 5MP25453 Manual Storage Tube 39 2 5MP1002 1/4” UNC X 3/4” Hex Bolt 40 2 5MP1629 1/4” UNC Nylock Hex Nut


76312 4544 76312


12

3

4

5

6

7

8 9 1011

1213

14

15

161718

19

20

21

22

2324

25

26

9

27

28

2931

32

33

32

3334

34 35

36

37

37

39

40

38

33

34

35

36

30


NOTICE: Do not operate the AF11D 96” Loader Mounted Front Blade on 7000 series tractors. The horse-power and overall vehicle weight of the 7000 series tractors will exceed the working capacity of the blade.

ITEM REQ’D PART NO. DESCRIPTION 1 2 5MP17139 Male Coupler 8FBo 1/2” Body 2 2 5MP3338 8MBo-6FBo Straight Connector 3 2 5FP0310125 1/4” Hose X 81” 6FFS-6MBo 4 1 5FPLAF1421 Rubber Hole Gasket 5 2 5FP032115 6MBo-6MFS 45° Elbow

6 2 5FPLAF4563 Cylinder Assembly 7 4 5MP1149 3/4” UNC X 5” Hex Bolt 4 5MP1936 3/4” UNC Torque Lock Nut 8 1 5FPLAF900507 Mounting Frame (600 & 700 Series Loader) 1 5FPLAF900509 Mounting Frame (Global Carrier Series Loader) 9 4 5MP2560 M12 Hex Nut (600 & 700 Series Loader ONLY) 10 1 5FP1352136 Right Latch Pin (600 & 700 Series Loader ONLY)

11 2 5FP0710145 Trip Pin (600 & 700 Series Loader ONLY) 12 2 5MP10195 Roll Pin (600 & 700 Series Loader ONLY) 13 1 5FP1352135 Left Latch Pin (600 & 700 Series Loader ONLY) 14 2 5FP0710144 Compression Spring (600 & 700 Series Loader ONLY) 15 2 5MP1096 1/2” UNC X 3” Hex Bolt 2 5MP1841 1/2” UNC Torque Lock Nut

16 1 5FPLAF9008 Bushing 17 1 5FPRHW5970 Machine Bushing 18 1 5FP1353209 Pivot Pin 19 1 5MP6616 Grease Fitting 20 4 5FPRHW8065 Spade Bolt 8 5MP1517 5/8” Flat Washer 8 5MP1230 5/8” UNC Hex Nut

21 4 5FPLAF6405 Trip Spring 22 1 5FP1353201 Pivot Mounting 23 3 5MP1194 1” UNC X 4-1/2” Hex Bolt 24 3 5MP1541 1” UNC Nylock Nut 25 1 5FPLAF1513 96” Blade

26 1 5FP1351824 96” Wear Edge 27 8 5MP1118 5/8” UNC X 2-1/2” Hex Bolt 8 5MP1506 5/8” Lock Washer 8 5MP1230 5/8” UNC Hex Nut 28 2 5FPRHW8064 Klik Pin 29 40 5FP0710126 1-5/8” SAE Flat Washer 30 2 5FPLAF1485 Skid Shoe

31 2 5FP5010019 AmberReflectingTape2”x9” 32 2 5FP5010018 RedReflectingTape2”x9” 33 2 5FP1003751A WarningDecal,CrushingandPinchingHazard 34 - ----- SerialNumberIdentificationTagLocation 35 1 5FP1002423 Warning Decal, Read Manual, No Riders

36 1 5MP40151 Warning Decal, High Pressure Fluid 37 2 5FP500721 WarningDecal,CrushHazard 38 1 5MP25453 Manual Storage Tube 39 2 5MP1003 1/4” UNC X 1” Hex Bolt 40 2 5MP1629 1/4” UNC Nylock Hex Nut

76312 4746 76312

AF12D & AF12G 96” LOADER MOUNTED FRONT BLADE600, 700 & GLOBAL CARRIER SERIES LOADERS

12

3

4

567

8

9

10

11

12 13 14

1516

17

1819

20

21

22

23

24

26

25

27

28

29

3031

32 33

3 12

34

35

33

3435

3637

38

39

39

4041

42

35

36

37

38


ITEM REQ’D PART NO. DESCRIPTION 1 2 5MP17139 Male Coupler 8FBo 1/2” Body 2 2 5FPLAF4343 3/8” Hose X 78” 6FJX-8MBo 3 2 5MP30379 6MJ-6MJ-6MJ Bulkhead Tee (Includes Nut) 4 2 5FPLAF4332 3/8” Hose X 16” 6FJX-6FJX 5 2 5MP3457 6MJ-6MBo Straight Connector 6 2 5MP3434 6MBo-6MJ 90° Elbow 7 4 5MP1049 3/8” UNC X 2-1/2” Hex Bolt 4 5MP1837 3/8” UNC Torque Lock Nut 8 4 5FPLAF1487 Cylinder Pin 9 2 5FP035733 Cylinder Assembly 10 2 5FPLAF4349 3/8” Hose X 26” 6FJX-6FJX

11 1 5FPLAF150907 Mounting Frame (600 & 700 Series Loader) 1 5FPLAF150909 Mounting Frame (Global Carrier Series Loader) 12 4 5MP2560 M12 Hex Nut (600 & 700 Series Loader ONLY) 13 1 5FP1352136 Right Latch Pin (600 & 700 Series Loader ONLY) 14 2 5FP0710145 Trip Pin (600 & 700 Series Loader ONLY) 15 2 5MP10195 Roll Pin (600 & 700 Series Loader ONLY) 16 1 5FP1352135 Left Latch Pin (600 & 700 Series Loader ONLY) 17 2 5FP0710144 Compression Spring (600 & 700 Series Loader ONLY) 18 1 5FPLAF1483 Bushing 19 2 5FPRHW5971 Machine Bushing 20 2 5MP1124 5/8” UNC X 4” Hex Bolt 2 5MP1839 5/8” UNC Torque Lock Nut

21 1 5FPLAF1488 Pivot Pin 22 1 5MP6616 Grease Fitting 23 4 5FPRHW8065 Spade Bolt 8 5MP1517 5/8” Flat Washer 8 5MP1230 5/8” UNC Hex Nut 24 4 5FPLAF6405 Trip Spring 25 1 5FPLAF1510 Pivot Mounting 26 3 5MP1194 1” UNC X 4-1/2” Hex Bolt 3 5MP1541 1” UNC Nylock Nut 27 1 5FPLAF1513 96” Blade 28 1 5FP1351824 96” Wear Edge 29 8 5MP1118 5/8” UNC X 2-1/2” Hex Bolt 8 5MP1506 5/8” Lock Washer 8 5MP1230 5/8” UNC Hex Nut 30 2 5FPRHW8064 Klik Pin

31 40 5FP0710126 1-5/8” SAE Flat Washer 32 2 5FPLAF1485 Skid Shoe 33 2 5FP5010019 AmberReflectingTape2”x9” 34 2 5FP5010018 RedReflectingTape2”x9” 35 2 5FP1003751A WarningDecal,CrushingandPinchingHazard 36 - ----- SerialNumberIdentificationTagLocation 37 1 5FP1002423 Warning Decal, Read Manual, No Riders 38 1 5MP40151 Warning Decal, High Pressure Fluid 39 2 5FP500721 WarningDecal,CrushHazard 40 1 5MP25453 Manual Storage Tube 41 2 5MP1003 1/4” UNC X 1” Hex Bolt 42 2 5MP1629 1/4” UNC Nylock Hex Nut

76312 4948 76312


12

3

4

567

8

9

10

11

12 13 14

1516

17

1819

20

21

22

23

24

26

25

27

28

29

3031

32 33

3 12

34

35

33

3435

3637

38

39

39

4041

42

35

36

37

38


ITEM REQ’D PART NO. DESCRIPTION 1 2 5MP17139 Male Coupler 8FBo 1/2” Body 2 2 5FPLAF4343 3/8” Hose X 78” 6FJX-8MBo 3 2 5MP30379 6MJ-6MJ-6MJ Bulkhead Tee (Includes Nut) 4 2 5FPLAF4332 3/8” Hose X 16” 6FJX-6FJX 5 2 5MP3457 6MJ-6MBo Straight Connector 6 2 5MP3434 6MBo-6MJ 90° Elbow 7 4 5MP1049 3/8” UNC X 2-1/2” Hex Bolt 4 5MP1837 3/8” UNC Torque Lock Nut 8 4 5FPLAF1487 Cylinder Pin 9 2 5FP035733 Cylinder Assembly 10 2 5FPLAF4349 3/8” Hose X 26” 6FJX-6FJX

11 1 5FPLAF150907 Mounting Frame (600 & 700 Series Loader) 1 5FPLAF150909 Mounting Frame (Global Carrier Series Loader) 12 4 5MP2560 M12 Hex Nut (600 & 700 Series Loader ONLY) 13 1 5FP1352136 Right Latch Pin (600 & 700 Series Loader ONLY) 14 2 5FP0710145 Trip Pin (600 & 700 Series Loader ONLY) 15 2 5MP10195 Roll Pin (600 & 700 Series Loader ONLY) 16 1 5FP1352135 Left Latch Pin (600 & 700 Series Loader ONLY) 17 2 5FP0710144 Compression Spring (600 & 700 Series Loader ONLY) 18 1 5FPLAF1483 Bushing 19 2 5FPRHW5971 Machine Bushing 20 2 5MP1124 5/8” UNC X 4” Hex Bolt 2 5MP1839 5/8” UNC Torque Lock Nut

21 1 5FPLAF1488 Pivot Pin 22 1 5MP6616 Grease Fitting 23 4 5FPRHW8065 Spade Bolt 8 5MP1517 5/8” Flat Washer 8 5MP1230 5/8” UNC Hex Nut 24 4 5FPLAF6405 Trip Spring 25 1 5FPLAF1510 Pivot Mounting 26 3 5MP1194 1” UNC X 4-1/2” Hex Bolt 3 5MP1541 1” UNC Nylock Nut 27 1 5FPLAF1514 108” Blade 28 1 5FP1350727 108” Wear Edge 29 9 5MP1118 5/8” UNC X 2-1/2” Hex Bolt 9 5MP1506 5/8” Lock Washer 9 5MP1230 5/8” UNC Hex Nut 30 2 5FPRHW8064 Klik Pin

31 40 5FP0710126 1-5/8” SAE Flat Washer 32 2 5FPLAF1485 Skid Shoe 33 2 5FP5010019 AmberReflectingTape2”x9” 34 2 5FP5010018 RedReflectingTape2”x9” 35 2 5FP1003751A WarningDecal,CrushingandPinchingHazard 36 - ----- SerialNumberIdentificationTagLocation 37 1 5FP1002423 Warning Decal, Read Manual, No Riders 38 1 5MP40151 Warning Decal, High Pressure Fluid 39 2 5FP500721 WarningDecal,CrushHazard 40 1 5MP25453 Manual Storage Tube 41 2 5MP1003 1/4” UNC X 1” Hex Bolt 42 2 5MP1629 1/4” UNC Nylock Hex Nut

76312 5150 76312


12

3

5

678

9

1011

17

1819

20

2122

23

2425

26

27

28

29

30

32

31

33

34

35

3637

38 39

3

18

40

41

39

4041

4243

44

45

45

46

47

48

41

42

43

44

13

12

1415

16

4


ITEM REQ’D PART NO. DESCRIPTION 1 2 5MP17139 Male Coupler 8FBo 1/2” Body 2 2 5FPLAF4343 3/8” Hose X 78” 6FJX-8MBo 3 2 5MP30379 6MJ-6MJ-6MJ Bulkhead Tee (Includes Nut) 4 2 5MP30031 6MJ-6FJX-6MJ Tee 5 2 5FPLAF4332 3/8” Hose X 16” 6FJX-6FJX 6 2 5MP3457 6MJ-6MBo Straight Connector 7 2 5MP3434 6MBo-6MJ 90° Elbow 8 4 5MP1049 3/8” UNC X 2-1/2” Hex Bolt 4 5MP1837 3/8” UNC Torque Lock Nut 9 4 5FPLAF1487 Cylinder Pin 10 2 5FP035733 Cylinder Assembly 11 2 5FPLAF4349 3/8” Hose X 26” 6FJX-6FJX 12 1 5FP035805 Dual Relief Block (1500 PSI) 2 5FPLAF4517 10MBo Plug (If Required) 13 2 5MP1028 5/16” UNC X 2-1/2” Hex Bolt 2 5MP1513 5/16” Flat Washer 2 5MP1502 5/16” Lock Washer 2 5MP1225 5/16” UNC Hex Nut 14 2 5FPLAF4405 6FBo-10MBo Straight Connector 15 2 5MP3457 6MJ-6MBo Straight Connector 16 2 5FPLAF4177 1/4” Hose X 9-1/4” 6FJX-6FJX 17 1 5FPLAF150907 Mounting Frame (600 & 700 Series Loader) 1 5FPLAF150909 Mounting Frame (Global Carrier Series Loader) 18 4 5MP2560 M12 Hex Nut (600 & 700 Series Loader ONLY) 19 1 5FP1352136 Right Latch Pin (600 & 700 Series Loader ONLY) 20 2 5FP0710145 Trip Pin (600 & 700 Series Loader ONLY) 21 2 5MP10195 Roll Pin (600 & 700 Series Loader ONLY) 22 1 5FP1352135 Left Latch Pin (600 & 700 Series Loader ONLY) 23 2 5FP0710144 Compression Spring (600 & 700 Series Loader ONLY) 24 1 5FPLAF1483 Bushing 25 2 5FPRHW5971 Machine Bushing 26 2 5MP1124 5/8” UNC X 4” Hex Bolt 2 5MP1839 5/8” UNC Torque Lock Nut 27 1 5FPLAF1488 Pivot Pin 28 2 5MP6616 Grease Fitting 29 4 5FPRHW8065 Spade Bolt 8 5MP1517 5/8” Flat Washer 8 5MP1230 5/8” UNC Hex Nut 30 4 5FPLAF6405 Trip Spring 31 1 5FPLAF1510 Pivot Mounting 32 3 5MP1194 1” UNC X 4-1/2” Hex Bolt 3 5MP1541 1” UNC Nylock Nut 33 1 5FPLAF1515 120” Blade 34 1 5FP1350757 120” Wear Edge 35 10 5MP1118 5/8” UNC X 2-1/2” Hex Bolt 10 5MP1506 5/8” Lock Washer 10 5MP1230 5/8” UNC Hex Nut 36 2 5FPRHW8064 Klik Pin 37 40 5FP0710126 1-5/8” SAE Flat Washer 38 2 5FPLAF1485 Skid Shoe 39 2 5FP5010019 AmberReflectingTape2”x9” 40 2 5FP5010018 RedReflectingTape2”x9” 41 2 5FP1003751A WarningDecal,CrushingandPinchingHazard 42 - ----- SerialNumberIdentificationTagLocation 43 1 5FP1002423 Warning Decal, Read Manual, No Riders 44 1 5MP40151 Warning Decal, High Pressure Fluid 45 2 5FP500721 WarningDecal,CrushHazard 46 1 5MP25453 Manual Storage Tube 47 2 5MP1003 1/4” UNC X 1” Hex Bolt 48 2 5MP1629 1/4” UNC Nylock Hex Nut

76312 5352 76312

HYDRAULIC ANGLE KIT 5FP10726AF11E 72” & 84” LOADER MOUNTED FRONT BLADE

12

3

4

5

6

7

HOSE ROUTING

HOSE GASKETHOSES

CYLINDER

COUPLERS

HYDRAULIC ANGLE KIT 5FP10726AF11E 72” & 84” LOADER MOUNTED FRONT BLADE


1 1 5MP106515 Male Coupler 6FBo 1/4” Body 1 5MP17139 Male Coupler 8FBo 1/2” Body 2 1 5MP106516 Female Coupler 6FBo 1/4” Body 1 5MP17140 Female Coupler 8FBo 1/2” Body 3 2 5MP3338 8MBo-6FBo Straight Connector (Used with 1/2” Body Couplers ONLY)

4 2 5FP0310116 3/8” Hose X 84” 6FFS-6MBo 5 1 5FPLAF1421 Hose Gasket 6 2 5MP30208 6MBo-6MFS Straight Connector 7 2 5FPLAF4563 Cylinder Assembly

76312 5554 76312

OPTIONAL RUBBER EDGE ASSEMBLIESLOADER MOUNTED FRONT BLADES

3

4

1

2

OPTIONAL RUBBER EDGE ASSEMBLIESLOADER MOUNTED FRONT BLADES

5FPLAF6486 RUBBER EDGE ASSEMBLY - AF11E 72” BLADE ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF9998 72” Rubber Edge 2 1 5FPLAF6466 72” Clamp Plate 3 6 5MP1096 1/2” UNC X 3” Hex Bolt 4 6 5MP1841 1/2” UNC Torque Lock Nut

5FPLAF6487 RUBBER EDGE ASSEMBLY - AF11E 84” BLADE ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF9996 84” Rubber Edge 2 1 5FPLAF6467 84” Clamp Plate 3 7 5MP1096 1/2” UNC X 3” Hex Bolt 4 7 5MP1841 1/2” UNC Torque Lock Nut

5FPLAF1551 RUBBER EDGE ASSEMBLY - AF11D & AF11G 84” BLADES ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF9404 48” Rubber Edge 1 5FPLAF9403 36” Rubber Edge 2 1 5FPLAF9408 48” Clamp Plate 1 5FPLAF9407 36” Clamp Plate 3 7 5MP10208 5/8” UNC X 3” Hex Bolt - Full Thread 4 7 5MP1839 5/8” UNC Torque Lock Nut

5FPLAF1552 RUBBER EDGE ASSEMBLY - AF11D, AF11G, AF12D & AF12G 96” BLADES ITEM REQ’D PART NO. DESCRIPTION 1 2 5FPLAF9404 48” Rubber Edge 2 2 5FPLAF9408 48” Clamp Plate 3 8 5MP10208 5/8” UNC X 3” Hex Bolt - Full Thread 4 8 5MP1839 5/8” UNC Torque Lock Nut

5FPLAF1553 RUBBER EDGE ASSEMBLY - AF12D & AF12G 102” BLADES ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF9404 48” Rubber Edge 1 5FPLAF9405 60” Rubber Edge 2 1 5FPLAF9408 48” Clamp Plate 1 5FPLAF9409 60” Clamp Plate 3 9 5MP10208 5/8” UNC X 3” Hex Bolt - Full Thread 4 9 5MP1839 5/8” UNC Torque Lock Nut

5FPLAF1554 RUBBER EDGE ASSEMBLY - AF12D & AF12G 120” BLADES ITEM REQ’D PART NO. DESCRIPTION 1 2 5FPLAF9405 60” Rubber Edge 2 2 5FPLAF9409 60” Clamp Plate 3 10 5MP10208 5/8” UNC X 3” Hex Bolt - Full Thread 4 10 5MP1839 5/8” UNC Torque Lock Nut

76312 5756 76312

OPTIONAL FLAP ASSEMBLIESLOADER MOUNTED FRONT BLADE

1

2

3

OPTIONAL FLAP ASSEMBLIES LOADER MOUNTED FRONT BLADE

5FPLAF6492 OPTIONAL 84” FLAP ASSEMBLY - AF11D & AF11G 84” BLADES

ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF6477 84” Rubber Flap 2 2 5FP1351708 Clamp Plate - 4 Hole 3 8 5MP1022 5/16” UNC X 1” Hex Bolt 8 5MP1934 5/16” UNC Torque Lock Nut

5FPLAF6493 OPTIONAL 96” FLAP ASSEMBLY - AF11D, AF11G. AF12D & AF12G 96” BLADES

ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF6478 96” Rubber Flap 2 1 5FP1351708 Clamp Plate - 4 Hole 1 5FP1351709 Clamp Plate - 5 Hole 3 9 5MP1022 5/16” UNC X 1” Hex Bolt 9 5MP1934 5/16” UNC Torque Lock Nut


ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF6479 108” Rubber Flap 2 2 5FP1351709 Clamp Plate - 5 Hole 3 10 5MP1022 5/16” UNC X 1” Hex Bolt 10 5MP1934 5/16” UNC Torque Lock Nut


ITEM REQ’D PART NO. DESCRIPTION 1 1 5FPLAF6480 120” Rubber Flap 2 1 5FP1351707 Clamp Plate - 3 Hole 2 5FP1351708 Clamp Plate - 4 Hole 3 11 5MP1022 5/16” UNC X 1” Hex Bolt 11 5MP1934 5/16” UNC Torque Lock Nut

76312 5958 76312

AS10H SERIES SNOW PUSH300 & 400 SERIES LOADERS

1

23

4

5

67

89

10

11

76

8

9

10

11


1 1 5FP135252904 72” Snow Push Frame 1 5FP135253304 84” Snow Push Frame 1 5FP135247704 96” Snow Push Frame

2 1 5FP1352539 72” Rubber Edge 1 5FP1352538 84” Rubber Edge 1 5FP1352467 96” Rubber Edge

3 1 5FP1352537 72” Rubber Edge Strap 1 5FP1352546 84” Rubber Edge Strap 1 5FP1351941 60” Rubber Edge Strap (96” Snow Push) 4 1 5FP1352476 30” Rubber Edge Strap (96” Snow Push)

5 Varies 5MP1094 1/2” UNC X 2-1/2” Hex Bolt Varies 5MP1516 1/2” Flat Washer Varies 5MP1505 1/2” Lock Washer Varies 5MP1228 1/2” UNC Hex Nut

6 2 5FP5010019 AmberReflectingTape2”x9” 7 2 5FP5010018 RedReflectingTape2”x9” 8 1 ------ SerialNumberIdentificationTagLocation 9 1 5FP1002423 Warning Decal, Read Manual, No Riders 10 1 5FPW50426 Warning Decal, Lock Pins 11 1 5FP1003751A WarningDecal,CrushingandPinchingHazard

AS10H SERIES SNOW PUSH300 & 400 SERIES LOADERS

76312 6160 76312

AS11E SERIES SNOW PUSH WITH TRIP EDGE300, 400 & 500 SERIES LOADERS

16

17

18

19

1

2

3

4

56

7

8

9

1011

12

13

14

15

16 1718

19

14 15


1 1 5FP1352490 96” Snow Push Trip Edge 1 5FP1352523 108” Snow Push Trip Edge 1 5FP1352516 120” Snow Push Trip Edge

2 1 5FP135250006 96” Snow Push Frame 1 5FP135251906 108” Snow Push Frame 1 5FP135251206 120” Snow Push Frame

3 1 5FP102649 96” Cutting Edge 1 5FP102650 108” Cutting Edge 1 5FP1352528 120” Cutting Edge

4 Varies 5FPRHW2663 5/8” UNC X 1-3/4” Plow Bolt - Grade 8 Varies 5FPRHW7607 5/8” UNC Flanged Lock Nut 5 8 5FPRHW8012 Cotter Pin

6 8 5FPRHW5932 1” Flat Washer - Grade 8 7 2 5FP102666 Pin 1” x 5” 8 2 5FP102657 Pin 1” x 27-1/4” (96”) 2 5FP102658 Pin 1” x 33-1/4” (108” and 120”) 9 2 5FP1351846 Trip Edge Spring Arm 10 4 5FPRHW7607 5/8” UNC Flanged Lock Nut

11 4 5MP1517 5/8” Flat Washer 12 4 5FPRHW8065 Spade Bolt 13 4 5FPLAF6405 Trip Spring 14 2 5FP5010019 AmberReflectingTape2”x9” 15 2 5FP5010018 RedReflectingTape2”x9”

16 1 ------ SerialNumberIdentificationTagLocation 17 1 5FP1002423 Warning Decal, Read Manual, No Riders 18 1 5FPW50426 Warning Decal, Lock Pins 19 1 5FP1003751A WarningDecal,CrushingandPinchingHazard

AS11E SERIES SNOW PUSH WITH TRIP EDGE300, 400 & 500 SERIES LOADERS

76312 6362 76312

OPTIONAL PULL BACK AND RUBBER EDGE ASSEMBLIESAS11E SERIES SNOW PUSH

1

2

3

4

5

6

7

7

8

OPTIONAL PULL BACK AND RUBBER EDGE ASSEMBLIESAS11E SERIES SNOW PUSH

5FP10733 OPTIONAL RUBBER EDGE ASSEMBLY- AS11E 96” Equipped with 5FP10730 Pull Back Assembly ITEM REQ’D PART NO. DESCRIPTION 1 1 5FP1351941 60” Clamp Plate 2 1 5FP1352476 30” Clamp Plate 3 1 5FP1352467 Rubber Edge 4 15 5MP1094 1/2” UNC X 2-1/2” Hex Bolt 30 5MP1516 1/2” Flat Washer 15 5MP1841 1/2” UNC Torque Lock Nut

5FP10734 OPTIONAL RUBBER EDGE ASSEMBLY- AS11E 108” Equipped with 5FP10731 Pull Back Assembly ITEM REQ’D PART NO. DESCRIPTION 1 1 5FP1352545 54” Clamp Plate 2 1 5FP1352544 42” Clamp Plate 3 1 5FP1352540 Rubber Edge 4 17 5MP1094 1/2” UNC X 2-1/2” Hex Bolt 34 5MP1516 1/2” Flat Washer 17 5MP1841 1/2” UNC Torque Lock Nut

5FP10735 OPTIONAL RUBBER EDGE ASSEMBLY- AS11E-120” Equipped with 5FP10732 Pull Back Assembly ITEM REQ’D PART NO. DESCRIPTION 1 1 5FP1351941 60” Clamp Plate 2 1 5FP1352545 54” Clamp Plate 3 1 5FP1352468 Rubber Edge 4 19 5MP1094 1/2” UNC X 2-1/2” Hex Bolt 38 5MP1516 1/2” Flat Washer 19 5MP1841 1/2” UNC Torque Lock Nut

5FP10730 OPTIONAL PULL BACK ASSEMBLY - AS11E 96” ITEM REQ’D PART NO. DESCRIPTION 5 1 5FP1352494 8’ Pull Back Trip Edge 6 2 5FP1352493 Pull Back Shoe Plate 7 14 5FPRHW1406 1/2” UNC X 1-3/4” Nylock Bolt 28 5MP1516 1/2” Flat Washer 14 5MP1505 1/2” Lock Washer 14 5MP1228 1/2” UNC Hex Nut 8 2 5FP5010019 AmberReflectingTape2”x9”

5FP10731 OPTIONAL PULL BACK ASSEMBLY - AS11E 108” ITEM REQ’D PART NO. DESCRIPTION 5 1 5FP1352548 9’ Pull Back Trip Edge 6 2 5FP1352493 Pull Back Shoe Plate 7 14 5FPRHW1406 1/2” UNC X 1-3/4” Nylock Bolt 28 5MP1516 1/2” Flat Washer 14 5MP1505 1/2” Lock Washer 14 5MP1228 1/2” UNC Hex Nut 8 2 5FP5010019 AmberReflectingTape2”x9”

5FP10732 OPTIONAL PULL BACK ASSEMBLY - AS11E - 120” ITEM REQ’D PART NO. DESCRIPTION 5 1 5FP1352526 10’ Pull Back Trip Edge 6 2 5FP1352493 Pull Back Shoe Plate 7 14 5FPRHW1406 1/2” UNC X 1-3/4” Nylock Bolt 28 5MP1516 1/2” Flat Washer 14 5MP1505 1/2” Lock Washer 14 5MP1228 1/2” UNC Hex Nut 8 2 5FP5010019 AmberReflectingTape2”x9”

76312 6564 76312

AB16A, AB16D & AB16G SMALL SQUARE BALE FORK600, 700, 800 & GLOBAL CARRIER SERIES LOADER

DIAGRAM 1 OF 2

33

34 35 36

37

3926

27

27

25

10119

918

18

19 18

13

1415

1632

3128

2829

30

47

26

25

24 202124

34

2322 12 14 15

16

39

37

36

33

6

78

1

2

35

5436

1718

1817 3

38

38

40

40

41 4243

44

4546


LIST 1 OF 2 ITEM REQ’D PART NO. DESCRIPTION 1 1 5MP107264 Bale Fork Frame Assembly - Global Carrier Loader 1 5MP111553 Bale Fork Frame Assembly - 600 & 700 Series Loader 1 5MP15469 Bale Fork Frame Assembly - 800 Series Loader 2 8 5MP83395 Mounting Tube (Included in Frame Assembly) 3 4 5MP14433 Tine Assembly (Included in Frame Assembly) 4 16 5MP6616 Grease Fitting 5 1 5MP14337 Adjustment Bar

6 2 5MP1345 1/2” UNF X 2-3/4” Hex Bolt 7 2 5MP1505 1/2” Lock Washer 8 2 5MP1478 1/2” UNF Hex Nut 9 2 5MP14331 Top Arm 10 1 5MP88928 Cylinder Assembly

11 2 5MP14327 Spacer 12 1 5MP14070 Pivot Pin 4-23/32” Long 13 1 5MP14365 Pivot Pin 7-5/8” Long 14 2 5MP1800 3/8” Hard Flat Washer 15 2 5MP1503 3/8” Lock Washer

16 2 5MP1296 3/8” UNF X 1-3/4” Hex Bolt 17 8 5MP10017 3/4” UNF X 2-3/4” Hex Bolt - GR8 18 24 5MP1649 3/4” Hard Flat Washer 19 8 5MP10001 3/4” UNF Locking Nut 20 1 5MP14231 Relief Valve - 1000 PSI

21 2 5MP1279 5/16” UNF X 2-3/4” Hex Bolt 22 2 5MP1502 5/16” Lock Washer 23 2 5MP1475 5/16” UNF Hex Nut 24 4 5MP30205 8MFS-12MBo Straight Connector 2 5MP30375 6MFS-12MBo Straight Connector (Global Carrier Series Loaders ONLY) (Use 5MP30375 instead of two 5MP30205 going to Hose 5MP38481)

25 1 5MP37790 3/8” Hose X 18” 8FFS-6FFS 90° 26 1 5MP37791 3/8” Hose X 10” 8FFS-6FFS 90° 27 2 5MP30208 6MFS-6MBo Straight Connector 28 2 5MP37982 1/2” Hose X 72” 10MBo-8FFS 90° (600/700/800 Series Loaders) 2 5MP38481 3/8” Hose X 80” 6FFS 90°-8FFS (Global Carrier Series Loaders) 29 1 5MP31886 Female Coupler 10FBo 1/2” Body (800 Serial Loader ONLY) 1 5MP15512 Male Coupler 10FBo 1/2” Body (Global Carrier, 600/700 Series Loaders ONLY)

76312 6766 76312


DIAGRAM 2 OF 2

33

34 35 36

37

3926

27

27

25

10119

918

18

19 18

13

1415

1632

3128

2829

30

26

25

24 202124

34

2322 12 14 15

16

39

37

36

33

6

78

1

2

35

5436

1718

1817 3

38

38

40

40

41 4243

44

4546


LIFT 2 OF 2 ITEM REQ’D PART NO. DESCRIPTION

30 1 5MP51753 Male Coupler Cover (Use with 5MP15512 Coupler) 31 1 5MP15512 Male Coupler 10FBo 1/2” Body 32 1 5MP51754 Female Coupler Cover (Use with 5MP31886 Coupler) 33 2 5FP500737 Warning Decal, Pinch Points 34 2 5FP5010010 Caution Decal, Do Not Detach Loader 35 2 5FPRDL3125 WarningDecal,CrushHazard

36 1 -------- SerialNumberIdentificationTagLocation 37 1 5MP40151 Warning Decal, High Pressure Fluid 38 2 5MP40964 Warning Decal, Falling Loads 39 1 5FP1002423 Warning Decal, Read Manual, No Riders 40 2 5MP30376 8MFS-10MBo Straight Connector (Global Carrier Series Loaders ONLY)

ITEMS #41 THROUGH #46 ARE USED ON 600 & 700 SERIES LOADERS ONLY

41 4 5MP2560 M12 Hex Nut 42 1 5FP1352136 Right Latch Pin 43 2 5FP0710145 Trip Pin 44 1 5FP1352135 Left Latch Pin 45 2 5MP10195 Roll Pin 46 2 5FP0710144 Compression Spring

76312 6968 76312

AH11A, AH11D & AH11G BALE HUGGER600, 700, 800 & GLOBAL CARRIER SERIES LOADERS

1

2

34

5

6

7

8

9

10

11

12

13

141516

17

1819

22

5

7

23

2524

26

27

28

20

22

23

24

25

26

27

28

21

2930

31

32

3334

AH11A, AH11D & AH11G BALE HUGGER600, 700, 800 & GLOBAL CARRIER SERIES LOADERS

ITEM REQ’D PART NO. DESCRIPTION 1 1 5MP107274 Bale Hugger Rear Frame - Global Carrier Series Loader 1 5MP111336 Bale Hugger Rear Frame - 600 & 700 Series Loader 1 5MP103817 Bale Hugger Rear Frame - 800 Series Loader 2 2 5MP102706 Arm 3 2 5MP1051 3/8” UNC X 3” Hex Bolt 4 2 5MP1837 3/8” UNC Deformed Lock Nut 5 2 5MP104701 Retaining Pin 6 1 5MP25453 Manual Storage Tube 2 5MP10134 5/16” UNC x 5/8” Hex Bolt 2 5MP1502 5/16” Lock Washer 7 2 5MP30204 6MBo-6MFS 90° Elbow 8 1 5MP102708 Cylinder Assembly 9 2 5MP104702 Cylinder Pin 10 2 5MP1650 Snap Ring

11 4 5MP6616 Grease Fitting 12 1 5MP38384 3/8” Hose X 28” 6FFS-6FFS 13 1 5MP38383 3/8” Hose X 22” 6FFS-6FFS 14 4 5MP30208 6MFS-6MBo Straight Connector 15 1 5MP105481 Valve Cover 16 2 5MP1026 5/16” UNF X 2” Hex Bolt 2 5MP1502 5/16” Lock Washer 17 2 5MP305976 3/8” Hose X 37” 6FFS 90°-8FFS (600/700/800 Series Loaders) 2 5MP38481 3/8” Hose X 80” 6FFS 90°-8FFS (Global Carrier Series Loaders) 18 2 5MP22552 8MFS-10MBo Straight Connector 19 2 5MP15512 Male Coupler 10FBo 1/2” Body 1 5MP31886 Female Coupler 10FBo 1/2” Body (800 Series Loader ONLY) 20 2 5MP51753 Male Coupler Cover (Use with 5MP15512 Coupler) 1 5MP51754 Female Coupler Cover (800 Series Loader ONLY)

21 1 5MP88536 Lock Valve - Gresen 22 2 5FP500737 Warning Decal, Pinch Points 23 2 5FPRDL3125 WarningDecal,CrushHazard 24 2 5FPW43023 Warning Decal, Falling Loads 25 2 5FP5010010 Caution Decal, Do Not Detach Loader 26 1 5FP1002423 Warning Decal, Read Manual, No Riders 27 1 5MP40151 Warning Decal, High Pressure Fluid 28 1 ----- SerialNumberIdentificationTagLocation

ITEMS #29 THROUGH #34 ARE USED ON 600 & 700 SERIES LOADERS ONLY 29 4 5MP2560 M12 Hex Nut 30 1 5FP1352136 Right Latch Pin 31 2 5FP0710145 Trip Pin 32 1 5FP1352135 Left Latch Pin 33 2 5MP10195 Roll Pin 34 2 5FP0710144 Compression Spring

76312 7170 76312

5MP107610 HYDRAULIC KITADAPTS FROM 1/4” BODY COUPLERS TO 1/2” BODY COUPLERS

1

2

3

3

5MP107610 HYDRAULIC KITADAPTS FROM 1/4” BODY COUPLERS TO 1/2” BODY COUPLERS


1 1 5MP17139 Male Coupler 8FBo 1/2” Body 2 1 5MP17140 Female Coupler 8FBo 1/2” Body 3 2 5MP3338 Straight Connector 8MBo-6FBo

INSTALLATION INSTRUCTIONS: 1. Remove existing 1/4” Body couplers from the power and return lines on the attachment. 2. InstallStraightConnectors(5MP3338)intotheexistingfittings.3. Install 1/2” Body couplers to straight connectors.

76312 7372 76312

5FPLAF4563 CYLINDER ASSEMBLY(AF11 SERIES HYDRAULIC ANGLE FRONT BLADES)

1

CYLINDER ROD

CYLINDER TUBE

5FPLAF4563 CYLINDER ASSEMBLY(AF11 SERIES HYDRAULIC ANGLE FRONT BLADES)


1 1 5FPLAF4613 Cylinder Seal Kit (Includes all seals and o’rings)

5MP65349 Installation Tool (Used for cylinder seal replacement.) (Not included with cylinder assembly.)

76312 7574 76312

5FP035733 CYLINDER ASSEMBLY(AF12 SERIES HYDRAULIC ANGLE FRONT BLADES)

1

2

3

4

5

6

7

8

9

10

111213

14

1

5FP035733 CYLINDER ASSEMBLY(AF12 SERIES HYDRAULIC ANGLE FRONT BLADES)

IMPORTANT: IF ORDERING REPLACEMENT PARTS FOR A HYDRAULIC ANGLE FRONT BLADE CYLINDER UP TO SN XFAF12D--37 & XFAF12G--25 REFER TO CYLINDER ASSEMBLY 5FPLAF4044)


1 3 5MP6616 Grease Fitting 2 1 5MP1483 Hex Nut 3 1 5MP87170 Piston 4 1 5MP1133735 Cylinder Tube 5 1 5MP77445 Cylinder Gland

6 1 5MP113734 Cylinder Rod 7 1 * Piston Seal 8 1 * Piston Ring 9 1 * O’Ring 10 1 * O’Ring 11 1 * Back-Up Washer 12 1 * Poly-Pak Seal 13 1 * O’Ring 14 1 * Rod Wiper

5MP45746 Cylinder Seal Kit (Includes all seals and o’rings)


76312 7776 76312

5FPLAF4044 CYLINDER ASSEMBLY - SERVICE PARTS ONLY(AF12 SERIES HYDRAULIC ANGLE FRONT BLADES UP TO SN# XFAF12D--37 & XFAF12G--25)

1

2

3

4

5

6

7

7

1

5FPLAF4044 CYLINDER ASSEMBLY - SERVICE PARTS ONLY(AF12 SERIES HYDRAULIC ANGLE FRONT BLADES UP TO SN# XFAF12D--37 & XFAF12G--25)


1 2 5MP6616 Grease Fitting 2 1 NA Hex Nut 3 1 NA Piston 4 1 NA Cylinder Tube 5 1 NA Cylinder Gland

6 1 NA Cylinder Rod 7 1 5FPLAF4005 Cylinder Seal Kit (Includes all seals and o’rings)


76312 7978 76312

5MP88928 CYLINDER ASSEMBLY(AB16 SERIES SMALL SQUARE BALE FORKS)

1

2

3

45

67

8

9

10

11

12

1314

15

16

17

2

17

5MP88928 CYLINDER ASSEMBLY(AB16 SERIES SMALL SQUARE BALE FORKS)


1 1 5MP88926 Cylinder Tube 2 1 5MP88919 Bushing 3 1 5MP1483 Lock Nut 4 1 * Piston Ring 5 1 * O’Ring 6 1 5MP50252 Aluminum Piston 7 1 * O’Ring 8 1 5MP5421 Washer 9 1 * O’Ring 10 1 * Back-Up Washer 11 1 * O’Ring 12 1 5MP77458 Gland 13 1 * Poly-Pak Seal 14 1 * Rod Wiper 15 1 5MP88927 Cylinder Rod 16 1 5MP88918 Bushing 17 2 5MP6616 Grease Fitting

5MP45617 Cylinder Seal Kit (Includes all parts marked with an asterisk (*). Parts are not sold separately.


76312 8180 76312

5MP102708 CYLINDER ASSEMBLY(AH11 SERIES BALE HUGGERS)

1

2

3

4

5

6

7

89

1011

1213

14

1

5MP102708 CYLINDER ASSEMBLY(AH11 SERIES BALE HUGGERS)


1 2 5MP6616 Grease Fitting 2 1 * Lock Nut 3 1 5MP18440 Aluminum Piston 4 1 5MP102815 Cylinder Tube 5 1 5MP18433 Gland

6 1 5MP102819 Cylinder Rod 7 1 * O’Ring 8 1 * Piston Ring 9 1 * O’Ring 10 1 * O’Ring

11 1 * Back-up Washer 12 1 * Poly-Pak Seal 13 1 * O’Ring 14 1 * Rod Wiper

5MP45821 Cylinder Seal Kit (Includes all parts marked with an asterisk (*). Parts are not sold separately.


PART NUMBER5MP76312

REV. 7

Documents

LOADER ATTACHMENTS AE11 AF11 - John Deeremanuals.deere.com/cceomview/5MP76312_19/Output/5MP76312.pdfab16 ae11 af11 af12 ag10 ah11 as10 as11 manual #5mp76312 m-1474 6-25-12-7 operator’s