Upload
lamnhi
View
249
Download
7
Embed Size (px)
Citation preview
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
This list identifies works approved by Lloyd’s Register Group Limited (LR) for refining andthe manufacture of aluminium alloy plates, sections, bars and castings in accordance withthe requirements of LR's Rules for the Manufacture, Testing and Certification of Materials,Chapter 8.
The information listed for each works is a summary of the product, grade and maximumthickness (for round bar, maximum diameter and for castings, maximum weight)
Where required further information should be obtained from the current certificate ofapproval issued to the manufacturer by LR.
Works designated "MQS Approved" are also approved under the Materials Quality Schemein accordance with LR's Rules for the Manufacture, Testing and Certification of Materials,Chapter 1 Section 2.
Approval only covers the manufacturing location listed, it does not extend to other worksowned by the same company.
The local LR surveying office is also listed.
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers,employees or agents are, individually and collectively, referred to in this clause as 'Lloyd'sRegister'. Lloyd's Register assumes no responsibility and shall not be liable to any personfor any loss, damage or expense caused by reliance on the information or advice in thisdocument or howsoever provided, unless that person has signed a contract with therelevant Lloyd's Register entity for the provision of this information or advice and in thatcase any responsibility or liability is exclusively on the terms and conditions set out in thatcontract.
List 6a
Approved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
As at 10 April 2018
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Australia
22.006082-T5, 6082-T6 MelbourneSectionsCAPRAL ALUMINIUM LIMITED22.006082-T5, 6082-T6Bars
Tel: +61 (0)3 9358 8138 Fax: +61 (0)3 9357 9952 eail to: [email protected] web: www.capral.com.au
Certificate # MD00/4126/0002/6a Expiry date: 26/02/2019
CAMPBELLFIELDVIC 3061
151, Barry Road
40.006082-T6 SydneySectionsG. JAMES EXTRUSION CO., PTY., LTD.
Tel: +61 7 3877 2785 Mob: 0402 894 605email: [email protected] web: www.gjames.com
Certificate No: MD00/4621/0001/6a Expiry Date: 11/10/2019
26 Long Street,Smithfield NSW 2164,
Austria
63.505083-H116, 5086-H116 ViennaPlatesAMAG ROLLING GmbH76.205083-H321
150.005083-H1117.003003-H14*Coils
tel: +43 7722 801 2644 fax: +43 7722 804 98web: www:amag.at*Approved applications only.Certificate # MD00/3189/0008/6a Expiry date: 15/09/2020
A-5282 RanshofenP.O. 32
304.00Al-Mg-Si grades ViennaRefining & Semi FinishedHAMMERER ALUMINIUM INDUSTRIES GmbH
Tel No. +43 7722 891 0 Fax No: +43 7722 891 458
E-mail: [email protected]
Website: www.hai-aluminium.at
Certificate No: MD00/4636/0001/6a Expiry Date: 30/11/2019
5282 Ranshofen.Lamprechtshausener Straße 69
Belgium
0.453003-O*, 3003-H12* AntwerpCoilsALERIS ALUMINIUM N.V.6.003003-H14*0.453003-O*, 3003-H12*Plates from coils6.003003-H14*
Tel: +32 (0)15 30 26 40 Fax: +32 15 30 26 22(0) Email to: [email protected] Web: http://www aleris-duffel.com
Certificate #: MD00/4462/0001/6a Expiry date: 31/03/2018
* for approved applications only
B-3570 DuffelA.Stocletlaan 87
10.006005A-T6, 6082-T6 AntwerpSectionsSAPA RC PROFILES NV/SA
Tel: +32 51 72 97 14 Email: [email protected]
Web: http//:www.sapagroup.com
Certificate Number: MD00/3856/0003/6a Expiry date: 06/11/2019
Kortemarkstraat 52.BE-8810Lichtervelde
As at 10 April 2018 2Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Canada
1150.00Al-Si7Mg TorontoCastingsCAF INNOVATIVE SHAPECASTING
Tel: 519 624 9997 Fax: 519 624 0789email: [email protected] web: www.shapecasting.comCertificate No:MD00/4536/0001/6a Expiry Date: 20/12/2018
Approval includes grade A356-T6 to ASTM B26 for approved applications.
Heat treatment is sub contracted.
Cambridge,Ontario,
458 Dobbie Drive
N1T 1ST
75.00Al-Si7Mg Vancouver BCCastingsHASTINGS BRASS FOUNDRY LTD.
Tel: +1 604 253 2811 Fax: +1 604 253 3133 Email to: [email protected] includes ASTM B26/B26M-12 Grade 356
Certificate Number: MD00/4325/0001/6a Expiry date: 28/05/2017
236 Clark DriveVancouver, BCV5L 3H3
100.00Al-Si7Mg Vancouver BCCastingsPACIFIC MAKO
Tel: +1 604 856 6668 Fax: +1 604 856 6512email: [email protected] web: www.pacmak.comApproval includes ASTM B26 grade A356.0-T6, accepted for approved applications.Not approved for weld repairs.Certificate No: MD00/4570/0001/6a Expiry Date: 24/04/2019
5481-268 Street,Langley, BCV4W 3W1
China, People's Republic of
5083, 5086 NanjingRefining & Semi FinishedALERIS ALUMINUM (ZHENJIANG) Co., Ltd.50.005083-O, 5083-H116, 5083-H112,
5086-H116Plates
Tel : +86 511 8530 7358 Fax: +86 511 8530 7222E-Mail : [email protected] Web: http://www.aleris.comCertificate #: MD00/4332/0002/6a Expiry date: 05/06/2020
111 Caijia Road,Jingkou Industrial Zone,Zhenjiang, Jiangsu Province, 212006
520.005083, 5086 GuangzhouRefining & Semi FinishedALNAN ALUMINIUM INC.50.005083-O, 5083-H111, 5083-H116,
5083-H112, 5083-H321, 5086-O,5086-H111, 5086-H112, 5086-H116
Plates
Tel: 86 771 6734104, Fax: +86 771 4950921
E-mail: [email protected]
Website: www.alnanaluminium.com
Certificate No: MD00/4744/0001/6a Expiry Date: 22/01/2018
Jiangnan,Jiangnan District, 530031,
No. 55, Tinghong Road,
Nanning.
6082 WuhanRefining & Semi FinishedCHONGQING FENGHE ALUMINIUM CO. LTD
Tel: +86-23-65800038 Fax: +86-23-65800849E-mail: [email protected], Lvcheng Boulevard,Xipeng,Jiulongpo DistrictChongqing City. 401326
Certificate No: MD00/4513/0001/6a Expiry Date: 30/09/2015
XipengJiulongpo District,
74-2, Lvcheng Boulevard,
Chongqing City. 401326
As at 10 April 2018 3Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
1.05Al-Si9Cu* Shanghai PortCastingsDYNACAST (SUZHOU) LTD.
Tel: +86 512 5772 5588 Fax:+86 21 5774 1320Web: www.dynacast.comCertificate #: MD00/4500/0001/6a Expiry date: 19/07/2018
No. 389 South JingTang RoadQianDeng, KunShan215341
Al-Mg grades WuhanRefining & Semi FinishedHENAN ZHONGFU INDUSTRIAL Co., Ltd.50.005083-O, 5083-H111, 5754-O,
5754-H111Plates
8.005083-O, 5083-H111, 5754-O,5754-H111
Coils
Tel: +86 0371 85613658 Fax: +86 0371 85613706
Certificate No.: MD00/4494/0001/6a Expiry Date: 29/06/2018
Zhanjie Town,Gongyi City,
Yulian Industrial Zone,
Henan Province,
12.00Al-Si7Mg, AlSi7Mg0,3* JiangyinCastingsJINGYI ALUMINIUM PRECISION CASTING Co. LTD
Tel: 00-86-519-85501188 Fax: 00-86-519-85505768
E-mail: [email protected]
Website: www.jingyicasting.com
Certificate No. MD00/4560/0001/6a Expiry Date: 22/03/2019
Qinglong,Tianning District, Changzhou,
Tongjia Industrial Park,
Jiangsu.
555.00Al-Mg-Si grades QingdaoRefining & Semi FinishedLONGKOU CONGLIN ALUMINUM CO., LTD.43.006005A-T6, 6061-T6, 6082-T5, 6082-T6Sections
Tel: +86 535 8560925 Fax: +86 535 8563202
E-mail: [email protected]
Website: www.conglin.com.cn
Certificate #: MD00/4430/0002/6a Expiry date: 02/02/2021
Longkou CityShandong Province 265705
Conglin Industry District
18.006082-T6 WuhanSectionsSAPA CHALCO ALUMINIUM PRODUCTS (CHONGQING)COMPANY LTD
Xipeng Aluminium Industrial Park,Jiu Longpo District,Chongqing. 401326Tel: +86 023 61968222 Fax: +86 023 6198408.E-mail: [email protected]: www.sapachalco.com
Certificate No: MD00/4512/0001/6a Expiry Date: 27/09/2015
Jiu Longpo District,Chongqing.
Xipeng Aluminium Industrial Park
401326
15.006061-T6, 6082-T6, 6063-T6* JiangyinSectionsSAPA EXTRUSION (JIANGYIN) CO LTD80.006061-T6, 6082-T6, 6063-T6*Bars
Tel No: +(86) 510 86909818 Fax No: +86 510 86909880Email: [email protected]: www.sapagroup.com
Certificate No: MD00/4433/0001/6a Expiry Date: 14/02/2018
No: 888, Shiji Avenue (S), Zhouzhuang Town,Jiangyin City,
Jiangyin
Jiangsu Province. Post Code: 214423
5083 QingdaoRefining & Semi FinishedSHANDONG NANSHAN ALUMINIUM Co. , LTD50.005083-O, 5083-H116, 5083-H112,
5083-H321Plates
As at 10 April 2018 4Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Tel: + 86 535 8785086 Fax: + 86 535 8785086
Website: www.nanshan.com.cn
Certificate No. MD00/4645/0002/6a Expiry Date: 28/12/2019
Donghai Industrial Park,Xufu Town, Longkou City,
Plate and Sheet Company
Shangdong Province.
5.005083-O, 5754-O WuhanPlatesSOUTHWEST ALUMINIUM (GROUP) CO., LTD.30.005083-H112, 5754-H11240.005083-H32150.005086-O, 5086-H111, 5086-H112,
5086-H116, 5456-H116, 5456-H321500.002618-T6Forgings*
Grade 5754 plate is acceptable for approved applications not in direct contact with seawater,
*Accepted for approved applications.
Tel: +86 (23) 65808767 Fax: +86 23 65808767
E-mail: [email protected]
Website: www.swa.com.cn
Certificate No: MD00/2921/0008/6a Expiry date: 11/10/2020
Jiou Long-po District,Chongqing CityChongqing City,
Xipeng
5083 QingdaoRefining & Semi FinishedTIANJIN ZHONGWANG ALUMINIUM CO., LTD.50.005083-O, 5083-H111, 5083-H116,
5083-H112, 5083-H321Plates
Tel: +86 22 5966 3843 Fax: +86 22 5966 3800email: [email protected] web: www.zhongwangtj.com
Certificate No: MD00/4680/0001/6a Expiry Date: 06/07/2017
North of Wuning Road,Auto Parts Industrial Park,Tianjin City,
0.01Al-Si7Mg Shanghai PortCastingsYUANXING LOCOMOTIVE PARTS (LINHAI) LTD
Tel: 139-0676-7679
E-mail: yuonxing_k263.net
Certificate No: MD00/4629/0001/6a Expiry Date: 07/11/2019
Youxi Town,Linhai City.
Industrial Park
Zhejiang Province
Czech Republic
61.002618A-T6 PragueForgings*CZECH PRECISION FORGE A.S.
Tel: + 420 378 133 802 Fax: +420 378 132 516
E-mail: [email protected]
Website: www.cpforge.com
Certificate No: MD00/3049/0003/6a Expiry Date: 09/02/2020
301 00 PlzenTylova 1/57
116.00Al-Si10Mg PragueCastingsSLEVARNA A MODELARNA NOVE RANSKO, s.r.o.
Tel No +420 569 669 480 Fax No. +420 569 669 487
E-mail: [email protected]
Website: www.slevarna.cz
Certificate #: MD00/4186/0002/6a Expiry date: 22/06/2019
Nove Ransko 234582 63 †dírec nad Doubravou
As at 10 April 2018 5Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
20.007022-T6, 2618A-T6 PragueForgings*STROJMETAL ALUMINIUM FORGING s.r.o.
Tel: +420 204 672 302 Fax: +420 204 672 028
Certificate #: MD00/3898/0003/6a Expiry date: 22/03/2020
Ringhofferova 66,251 68 Kamenice
France
Al-Mg grades LyonRefining & Semi FinishedCONSTELLIUM ISSOIRE30.005086-H116, 5086-H321Plates40.005086-O, 5086-H111, 5086-H11250.005083-H11680.005383-H116, 5383-H321
170.005083-O, 5083-H111, 5083-H112,5083-H321, 5383-O, 5383-H111,5383-H112
Tel: +33 4 7355 5050 email: [email protected] web: www.constellium.comMaterials Quality Scheme approved - MQS 037Certificate #: MD00/1241/0011/6a Expiry date: 25/02/2019
Rue Yves LamourdedieuZl des Listes
Flat Rolled Products
63502 Issoire Cedex
200.005083 LyonForgings*L'UNION DES FORGERONS
Tel: +33 (0) 1 64 95 02 25 Fax: +33 (0) 1 64 95 09 89 Email: mailto:[email protected] Web: http://www.union-des-forgerons.frCertificate #: MD00/3229/0004/6a Expiry date: 23/03/2018
BP 16 - Z.A.91660 Méréville
12 Rue De La Pierre Follège
220.007175-T6 LyonForgings*LISI AEROSPACE - FORGES DE BOLOGNE
Tel: +33 3 25 30 42 20 email to: [email protected]
Certificate No: MD00/4324/0002/6a Expiry date: 27/05/2020
39 rue des ForgesBP 82138 BOLOGNE52310 BOLOGNE
5083, 5086, 5383 DunkerqueRefining & Semi FinishedRIO TINTO ALCAN
Tel: +33 (0) 3 28 23 60 00 Fax: +33 (0)3 28 23 60 99
E-mail: [email protected]
Website: www.riotinto.com
Certificate No: MD00/4724/0002/6a Expiry Date: 16.10.2020
BP 81ZIP Ouest
Aluminium Dunkerque
59279 Loon-Plage
7175-O* MarseilleRefining & Semi FinishedSABART AERO TECH - Tarascon sur Ariege France
Tel no: +33 561 024 064 Fax no: +33 561 024 011Email [email protected]:www.sabart-at.comCertificate no. MD00/4351/0002/6a Expiry Date 28/07/2018
Appproved supplier to Forges de Bologna*7175 included in this scope of approval
* for approved appplications only
BP 29,09401 Tarascon sur Ariege Cedex
As at 10 April 2018 6Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Germany
234.00Al-Si10Mg, AlSi7Mg0,3*, AlSi9Mg* HamburgCastingsAGVS ALUMINIUM-WERKE GMBH VILLINGEN
* For Approved Applications.
Tel: +49 7721 846031 Fax: +49 7721 846051
Email: mailto:[email protected]
Web : www.agvs.de
Certificate No. MD00/3355/0004/ 6a Expiry date: 12/07/2019
78048 Villingen-SchwenningenGoldenbühlstraße 14
All Grades HamburgRefining & Semi FinishedALERIS CASTHOUSE GERMANY GmbH
Tel: +49 0281 164881 4442 Fax: +49 0281 1648814393
Email: [email protected]
Website: www.aleris.com
Approval is for vertical cast billets 202 to 348 mm diameter, maximum weight 2000 Kgs for alloy' series 5xxx and 6xxx.
Certificate: MD00/3665/0004/6a Expiry date: 23/08/2018
Schleusenstr. 11D-46562 Voerde
510.00Al-Mg-Si grades, Al-Mg grades HamburgRefining & Semi FinishedALERIS CASTHOUSE GERMANY GmbH
Tel: 0049 261/891 7527Email: [email protected] Web: www.aleris.comCert Number: MD00/4616/0001/6a Expiry Date: 19/04/2019
Carl-Spaeter-Strasse 10D-56070Koblenz
70.005083-H116 HamburgPlatesALERIS ROLLED PRODUCTS GERMANY GMBH250.005059-O, 5059 H111, 5059 H116, 5059
H321, 5083-O, 5083-H111,5083-H112, 5083-H321, 5086-O,5086-H112, 5086-H321, 6061-T6,6082-T6
250.005083-O, 5083-H111, 5083-H112,5083-H321, 5086-O, 5086-H112,5086-H321, 6061-T6, 6082-T6
Sections
250.005083-O, 5083-H111, 5083-H112,5083-H321, 5086-O, 5086-H112,5086-H321, 6061-T6, 6082-T6
Bars
Tel: +49 (0)261 891-7527 Fax: +49 (0)261 891 9 7527 Email: mailto:[email protected] Web:www.aleris.comCertificate No. MD00/0697/0011/6a Expiry date: 19/04/2019
Carl-Spaeter-Straße 10D-56070 Koblenz
Al-Mg-Si grades, Al-Mg grades HamburgRefining & Semi FinishedALUMINIUMWERK UNNA AG160.005083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5754-O,5754-H111, 6061-T5, 6061-T6,6082-T5, 6082-T6
Sections
160.005083-O, 5083-H111, 5083-H112,5086-O, 5086-H111, 5754-O,5754-H111, 6061-T5, 6061-T6,6082-T5, 6082-T6
Bars
150.003003-O*, 3003-F*Extrusions
Includes approval for pipes and tubes with 250 mm outer diameter (max.) and 40 mm wall thickness (max).Tel: +49 2303 206 148 Fax: +49 2303 206 117 Email: mailto:[email protected] Web: http://www.alunnatubes.comCertificate No. MD00/3152/0008/6a Expiry date: 16/03/2017
Uelzener Weg 36D-59425 Unna
350.00Al-Si10Mg, Al-Si7Mg HamburgCastingsC.F. MAIER LEICHTGUSSWERK GMBH & CO. KG
Tel: +49 (0)7328 81152 Fax: +49 7328 81193 EMail: [email protected] Web http://www.c-f-maier.deCertificate No. MD00/2037/0007/6a Expiry date: 11/07/2019
Postfach 1165D-89548 Königsbronn
Königsbronn
As at 10 April 2018 7Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
600.005083-O, 5083-H111, 5083-H112,5086-O, 5086-H111, 5086-H112,6005A-T6, 6061-T6, 6082-T6
HamburgSectionsCONSTELLIUM SINGEN GmbH
600.005083-O, 5083-H111, 5083-H112,5086-O, 5086-H111, 5086-H112,6005A-T6, 6061-T6, 6082-T6
Bars
Tel: +49 7731 2330 Email: mailto: [email protected] Web:http://www.constellium.comCertificate No. MD00/2654/0006/6a Expiry date: 16/03/2018
Alusingen Platz 1D-78224 Singen
9.005019* HamburgWireDRAHTWERK ELISENTAL W.ERDMANN GmbH & Co.
Tel: +49 2392 69790 Fax: +49 2392 697 8090E-mail to: [email protected] Web: http://www.elisental.de
Certificate #: MD00/4484/0001/6a Expiry date: 19/05/2018
* for approved applications only
58809 NeuenrodeWerdohler Strasse 40
680.00Al-Si10Mg, Al-Si7Mg HamburgCastingsHAL ALUMINIUMGUSS LEIPZIG GMBH
Tel: +49 341 453 40 850 Fax: +49 341 453 40 890
E-mail: [email protected]
Website: www.hal-gruppe.de
Certificate No. MD00/3363/0005/6a Expiry date: 30/07/2019
04178 LeipzigGutenbergstraße 20
10.005083-O, 5083-H111, 5083-H116,5083-H112, 5083-H321
HamburgPlatesHYDRO ALUMINIUM ROLLED PRODUCTS GmbH
10.005083-O, 5083-H111, 5083-H112,5083-H116, 5083-H321
Coils
Tel: +49 (0)2181 66 1381 Fax: +49 (0)2181 661864 Email: [email protected] Web: http://www.hydro.comCertificate No. MD00/0095/0007/6a Expiry date: 20/01/2018
Aluminiumstraße 1D-41515 Grevenbroich
Works Aluminium Norf GmbHGrevenbroich
10.005083-H112, 5083-H321, 5086-O,5086-H111, 5086-H112, 5086-H321
HamburgPlatesHYDRO ALUMINIUM ROLLED PRODUCTS GmbH
12.005083-O, 5083-H1115.003003-O*, 3003-H111*Coils
Tel:- +49 (0)40 74011-726 Fax:- +49 (0)40 74011-730 email: [email protected] web: www.hydro-aluminium.com/deutschlandCertificate No. MD00/2218/0009/6a Expiry date: 12/06/2019
Aluminiumstraße21129 Hamburg
750.00Al-Si10Mg, Al-Si7Mg HamburgCastingsMETALLGIEßEREI GUTSCHERA GmbH
Tel: +49 (0) 2592/1538 Fax: +49 (0) 2592/20826 Email: [email protected] Web: http://www.gutschera.deCertificate No. MD00/2269/0007/6a Expiry date: 18/11/2019
Industriestraße 4D-59379 Selm
1200.00Al-Si7Mg HamburgCastingsMETALLGUSS SEIFERT GMBH
Tel: 0049 (0) 2663 91540 Fax: 0049 (0) 2663 915429 Email:mail to: [email protected] Web Page: www.metallguss-seifert.deCertificate No. MD00/3449/0005/6a Expiry date: 20/11/2018
Boschstraße 8 - 10D-56457 Westerburg / Sainscheid
750.00Al-Mg3, Al-Si12, Al-Si10Mg,Al-Si7Mg, Al-Si5Cu*, Al-Si9Cu*,Al-Si8Cu3*, Al-Si(Cu)*, Al-Cu4Ti*,Al-Mg5(Si)*, Al-Zn10Si8Mg*,Al-Zn15Si8*
HamburgCastingsMetallgießerei an der Mulde GmbH
Tel: +49 (0) 37 31 / 39 69 61 Fax: +49 (0) 3731 39693 Email: mailto:[email protected] Web: http://www.m-adm.de* accepted for approved applications.Certificate Number: MD00/2745/0005/6a Expiry: 05/10/2018
Muldenhütten 22D-09599 Freiberg
As at 10 April 2018 8Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
500.00Al-Si10Mg, Al-Si7Mg, AlSi9Mg* HamburgCastingsOHM & HÄNER METALLWERK GMBH & CO. KG
Tel: +49 02761/921-457 Fax: +49 02761/921-555Email: mailto:[email protected] Web:http://www.ohmundhaener.deCertificate No. MD00/2257/0007/6a Expiry date: 25/09/2019
Im Grüntal 1D-57462 Olpe
Al-Mg-Si grades, Al-Mg grades HamburgRefining & Semi FinishedOTTO FUCHS KG260.005083-O, 5086-O, 6061-T6, 6082-T6Sections160.005083-O, 5086-O, 6061-T6, 6082-T6Bars
2000.005083-O, 5083-F, 5083-H321, 5086-O,5086-F, 5086-H321, 6061-T6, 6082-T6
Forgings*
Tel. 49(0)2354 73 897 Fax 49(0)2354 73 201 Email: [email protected] Web page http://www.otto-fuchs.com* accepted for approved applicationsCertificate No. MD00/0553/0007/6a Expiry date: 05/03/2020
Derschlager Straße 26D-58540 Meinerzhagen
0.35Al-Si12, Al-Si10Mg,Al-Si12CuMgNi*
HamburgCastingsSECO GmbH
Tel: +49 (0) 3946 9079250 email [email protected] web www.secogmbh.de
Certificate #: MD00/3525/0002/6a Expiry date: 24/06/2020
Gross Orden 23D-06484 Quedlinburg
30.006063-T6*, 6063-T66* HamburgSectionsST EXTRUDED PRODUCTS GERMANY GMBH130.006082-T6
Tel: +49 (0) 3493 75475 Fax: +49 (0) 3493 75477 Email: [email protected] Web: http://www.step-g.com
Certificate: MD00/3781/0004/6a Expiry date: 27/04/2019
Devillestrasse 206749 Bitterfeld
WERK BITTERFELD
Al-Mg-Si grades, Al-Mg grades HamburgRefining & Semi FinishedST Extruded Products Germany GmbH Werk Bonn60.005083-O, 5083-H112, 5083-H321,
5086-O, 5086-H112, 5086-H321,6082-T6
Sections
60.005083-O, 5083-H112, 5083-H321,5086-O, 5086-H112, 5086-H321,6082-T6
Bars
Tel: +49 (0) 228 558 2755 Fax: +49 (0) 228 558 2874 Email:mailto:[email protected] Web:http://www.aleris.comIncluding ingots with a maximum diameter of 400 mm.Certificate No. MD00/1623/0008/6a Expiry date: 03/02/2019
Friedrich Wöhler Straße 2D-53117 Bonn
250.006061-T6, 6082-T6 HamburgSectionsWESERALU GmbH & Co. KG250.006061-T6, 6082-T6Bars
Tel +49 (0)571 38705 22 Fax +49 (0)571 38705 55 Email: mailto: [email protected] Web:http://www.weseralu.deCertificate #: MD00/1664/0008/6a Expiry date: 11/08/2020
Am Osthafen 5D-32423 Minden
76.00Al-Mg-Si Grades HamburgExtrusionsWIELAND-WERKE AG
Tel: +49 731 944 2508 Fax: +49 731 944 4208 Email: [email protected] Web: http://www.wieland.deThe scope of approval is for extruded finned tubes only with a maximum 5mm wall thickness in grades AlMn1 and AlMgSi0.5 supplied in the as extrudedcondition, accepted for approved applications.Certificate Number: MD00/3216/0004/6a Expiry: 27/01/2018
Graf-Arco-Strasse 36D-89079 Ulm
As at 10 April 2018 9Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Greece
230.006005A, 6061, 6082, Al-Mg-Si grades PiraeusRefining & Semi FinishedANOXAL S.A.
Tel: +30 226 205 3569 Mob: +30 697 440 3569email: [email protected]
Certificate No: MD00/4357/0002/6a Expiry date: 02/07/2020
Approval includes grades EN AW 6060 and 6063. Grades not covered by LR Rules are accepted for approved applications only.
3rd km Inofita-Agios Thomas Road,32011, Agios Thomas,Viotia,
20.006082-T6 PiraeusSectionsCOSMOS ALUMINIUM A.E.40.006082-T6Bars
Tel No: +30 2410 567576 Fax No: +30 2410 567570email: [email protected] web: www.cosmosaluminium.gr
Certificate No: MD00/4306/0003/6a Expiry Date 05/04/2020
Approval includes bars of square, rectangular, round and hexagonal shapes and section profiles of various shapes (flat or hollow) up to 5mm in thickness
Sections within Circumscribed Circle Diameter maximum 250mm x 5mm thickness.
Bars within Circumscribed Circle Diameter maximum 250mm x 40 mm thickness
8th km National Road Larissa - Athens,Larissa,
12.705083-H111, 5086-H111 PiraeusPlatesELVAL HELLENIC ALUMINIUM INDUSTRY S.A.50.005083-O, 5083-H116, 5083-H321,
5086-O, 5086-H116
Tel: +30 22620 53600 Fax: +30 22620 31347
Email: [email protected]
Web: http://www.elval.gr
Certificate No. MD00/2990/0009/6a Expiry date: 30/08/2018
GR-32011 Inofyta-Viotia57 km Athens Lamia National Road
203.00Al-Mg-Si grades, 3103* PiraeusRefining & Semi FinishedEPALME S.A.
Tel: +30 22620 30806 Fax: +30 22620 56300 email: [email protected] Web http://www.epalme.grCertificate No. MD00/4303/0001/6a Expiry date: 02/04/2017
Inofita, Viotia32011
India
Al-Mg-Si grades, Al-Mg grades ChennaiRefining & Semi FinishedHINDALCO INDUSTRIES LTD12.505083-O, 5083-H112, 5086-O,
6061-T6, 6082-T6Plates
25.005083-O, 5083-H112, 5086-O,5086-H112, 6061-T6, 6082-T5,6082-T6
Sections
50.005083-O, 5083-H112, 5086-O,5086-H112, 6061-T6, 6082-T5,6082-T6
Bars
Tel: +91 5446 252077-79 Fax: +91 5446 252107/252427 Email: [email protected] Web: http://www.hindalco.comCertificate No. MD00/0674/0008/6a Expiry date: 01/04/2019
P.O. RenukootDist. Sonbhadra 231217Uttar Pradesh
12.50Al-Si7Mg MumbaiCastingsVULKAN Technologies Pvt. Limited64.00Al-Si12, Al-Si10Mg
Tel: +91 20 6676 5541 Fax: +91 20 6676 5551 email [email protected] web: www.vulkanindia.comCertificate Number: MD00/3051/0006/6a Expiry: 19/01/2019
Village Kasar AmboliPirangut Industrial Area, Tal-Mulashi
GAT No. 539B
Dist. Pune 412115, Maharashtra
As at 10 April 2018 10Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Italy
50.006082-T5, 6082-T6 MilanSectionsBODEGA G. & C. S.P.A.
Tel: +39 035 438366 Fax: +39 035 4382300 Email: mailto:[email protected]: http://www.bodega.itCertificate No. MD00/3112/0005/6a Expiry date: 23/10/2019
24034 Cisano Bergamasco (BG)Via Binda di Sopra 1
90.00Al-Si7Mg VeniceCastingsF.A.M. S.r.l.
Tel +39 0546 41494 Fax +39 0546 41441 email: [email protected] web: www.fonderiafam.com
Certificate No. MD00/3288/0005/6a Expiry date: 26/11/2018
48018 GRANAROLO FAENTINO (RA)Via Pasolini, 38-39
30.006005A-T5, 6005A-T6, 6082-T5,6082-T6
MilanSectionsMETRA S.P.A.
Tel: +39 030 6819205 Fax: +39 030 6810260 Email: mailto:[email protected] Web: http://www.metra.itCertificate No. MD00/2975/0005/6a Expiry date: 04/05/2018
Via Stacca, 125050 Rodengo SaianoBrescia
65.00Al-Si7Mg VeniceCastingsSA & BAR S.r.l
Tel: +39 051 767022 Fax: +39 051 0547900
Certificate No. MD00/3949/0003/6a Expiry date: 17/09/2020
Via A. Boldrini, 26Frazione Quarto Inferiore40057 Granarolo Dell'Emilia (BO)
Al-Mg grades VeniceRefining & Semi FinishedSLIM FUSINA ROLLING S.r.l.8.005083-H128Plates
40.005083-H116, 5083-H32160.005083-O, 5083-H111, 5083-H112
Tel: +39 041 2917254 Fax: +39 041 2917212
Email: [email protected]
Web page http://www.alcoa.com
MATERIALS QUALITY SCHEME APPROVED - MQS 046
Certificate No. MD00/2605/0014/6a Expiry date: 13/06/2018
Via dell' Elettronica 3130176 Malcontenta
Stabilimento di Fusina
Loc. Fusina, Venezia
Japan
700.00Al-Si12, Al-Si7Mg KobeCastingsFUKUTATSU ALLOY MFG. CO., LTD.
Tel +81 78 991 2201 Fax +81 78 991 1523 email [email protected] web: www.fukutatsu.comNot approved for weld repair.Certificate No. MD00/0556/0007/6a Expiry date: 04/08/2019
TakatsukadaiNishi-ku
15, 1, 3 - Chome
Kobe
Al-Mg grades NagasakiRefining & Semi FinishedKOBE STEEL, LTD.150.005083-O, 5086-O, 5154A*Sections150.005086-O, 5154A*Bars360.005083-O
Tel: +81 83 246 3640 Fax: +81 83 346 1710
E-mail: [email protected] Website http://www.kobelco.co.jp
* accepted for approved applications
Certificate No. MD00/1947/0009/6a Expiry date: 09/11/2020
14-1, Minato-MachiChofu, Shimonoseki City,
Chofu Works
Yamaguchi Pref. 752-0953
As at 10 April 2018 11Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
370.005083-F, 2618-T6 KobeForgings*KOBE STEEL, LTD.2055.005083-O, 5083-H112
Tel: +81 594 77 2202 Fax: +81 594 77 2249 Email: [email protected]* accepted for approved applicationsCertificate No. MD00/2087/0009/6a Expiry date: 10/04/2017
Daian-choInabe-city
Daian Plant1100, Umedo
Mie-ken,
20.005083-O, 5083-H112 KobeSectionsLIGHT METALS EXTRUSION DEVELOPMENT CO., LTD.
Tel: +81 593 45 4228 Fax: +81 593 47 0355 Email: mailto:[email protected]
Includes approval for pipes and tubes with 280mm outer diameter and 20mm wall thickness (max)Certificate No. MD00/0930/0008/6a Expiry date: 01/06/2020
2-2, 2 chome, Higashi OgosoYokkaichiMie-ken
420.00Al-Si7Mg YokohamaCastingsMIURA CO., LTD.
Tel No: +81 248 86 2662 Fax No: +81 248 86 2663email: [email protected] web: www.miura1.co.jpCertificate No: MD00/4136/0002/6a Expiry Date 01/04/2019
Imaizumi,Sukagawa-city,
20-1 Kamitsuru, Aza
Fukushima 962- 0301
1200.00Al-Mg3, Al-Si12, Al-Si10Mg,Al-Si7Mg
KobeCastingsRYOSAN INDUSTRY CORPORATION
Tel: +81 (0)78 986 6617 Fax: +81 (0)78 986 4472 Email: [email protected] Web: http://www.ryosan-ind.co.jp Certificate No. MD00/1257/0008/6a Expiry date: 30/11/2020
Kita-kuKobe
57 Eibara Nagao-cho
300.005083-O KobeForgings*SEO KOATSU KOGYO CO., LTD.
Tel: +81 790 28 0590 Fax: +81 790 28 1140* accepted for approved applicationsCertificate No. MD00/1338/0007/6a Expiry date: 10/11/2019
869-20 Aza Kanzaki Ichikawa-choKanzaki-gun
Ichikawa Works
Hyogo-pref
Al-Mg grades YokohamaRefining & Semi FinishedUACJ CORPORATION35.005083-H116Plates
200.005083-O, 5083-H321
Tel +81 485 72 1316 Fax +81 485 73 5228 email: [email protected] web www.uacj.co.jpThe scope of approval includes for the manufacture of alloy 3003 supplied to ASAHIKASEI CORPORATION for use for transition joints. Certificate Number: MD00/1277/0011/6a Expiry: 09/03/2021
Fukaya CitySaitama Pref.
FUKAYA WORKS1351, Uwanodai
366-8511
5083 KobeRefining & Semi FinishedUACJ Corporation160.005083-OPlates
Tel: +81 52 654 1186 Fax: +81 52 654 0039 Email: mailto:[email protected] Web: http://www.uacj.co.jpCertificate No. MD00/1453/0008/6a Expiry date: 14/06/2018
Minato-kuNagoya
Nagoya Works3-1-12, Chitose
455-8670
5083 KobeRefining & Semi FinishedUACJ Corporation20.005083-H112Sections
120.005083-O600.005083-OBars
As at 10 April 2018 12Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Tel No: +81 52 654 1108 Fax no: +81 52 654 1189Email: [email protected]: http://www.suex.uacj-group.com
Includes approval for pipes and tubes with 150mm OD and 30mm wall thickness (max) and approval for pipe and tubes with 280mm OD and 20mm wallthickness (max) by subcontracted manufacture.
Certificate No: MD00/4047/0004/6a Certificate Expiry 14/06/2018
3-1-12 Chitose,Minato-ku,
UACJ Extrusion Nagoya CorporationNagoya Works,
Nagoya 455-8670
15.003003-O** KobePlatesUACJ Corporation80.005083-H321
200.005083-O
Tel No: +81 776 82 5843 Fax No: +81 776 82 5854Email: [email protected]:
Materials Quality Scheme Approved - Approval No. MQS010Certificate No: MD00/ 4230/ 0003/6a Expiry Date: 15/10/2018
* For thickness 29mm and above self annealing 5083 denoted as 5083(SA)** accepted for approved applications only
Sakai City,Fukui-Pref.,
Fukui Works21-1 Kurome Mikuni-cho
913 - 8588
Al-Mg grades YokohamaRefining & Semi FinishedUACJ Extrusion OYAMA Corporation20.005083-OSections
200.005083-OBars
Tel no; +81 285 23 2113 Fax No: +81 285 25 0567 Email mailto: [email protected]
Accepted for approved applicationsCertificate No:MD00/4261/0010/6a Expiry date 14/02/2018
Oyama City,Tochigi Pref.
560 Dotou
323-0812
1000.002618-T6 YokohamaForgings*UACJ Foundry & Forging Corporation2000.005083-O
Tel No: +81 285 24 3611 Fax +81 285 22 2884Email mailto: takashima. [email protected] group.comWeb http://www.uaccj.co.jpCertificate number MD00/4267/ 0002/6a Expiry date 12/02/2018
560, Dotou,Oyama City,
Foundry and Forging Works
Tochigi 323-0812
100.005083-O KobeForgings*YAMASHITA TANZOSHO CO., LTD.
Tel: (0)72 891 1421 Fax (0)72 892 2126* Accepted for approved applicationsCertificate No. MD00/3249/0004/6a Expiry date: 21/07/2018
6 Chome KatanoOsaka pref.
43-1 Ikuno
Korea
30.005083-O ChangwonSectionsALCOA KOREA Ltd.50.005083-OBars
120.006061-T6
Tel. +82 55 269-9581 Fax +82 55 269-9502 Email to: [email protected]: http://alcoa.comCertificate No. MD00/2078/0008/6a Expiry date: 31/03/2018
Changwon,Gyeongnam,
48, Jeongdong-ro,Seongsan-gu,
As at 10 April 2018 13Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
300.00Al-Si7Mg ChangwonCastingsDAESHIN METAL MANUFACTURING CO. LTD
Tel: + 82-55-296-1011, Fax: +82-55-296-6149
E-mail: [email protected]
Website: www.ds-al.com
Certificate No: MD00/4546/0001/6a Expiry Date: 31.01.2019
Euichang-Gu,Changwon-City,
24-11, Palryong-Dong,
Kyungnam.
50.00Al-Si7Mg SeoulCastingsKOREA LOST-WAX CO., LTD.
Tel: +82 31 499 8485 Fax: +82 31 431 6091email: [email protected] web: www.lostwax.co.kr
Certificate No. MD00/2664/0005/6a Expiry date: 09/03/2020
* Investment castings in alloy A357 accepted for approved applications.
#363-74, Gongdan 1-Daero,Siheung-City,Gyeonggi-Do, 15074
544.002618-T6 UlsanForgings*POONGSAN CORPORATION
Tel: +82 54 760 6693 Fax:P +82 54 760 6690 email: [email protected] www.poongsan.co.kr
* For Approved Applications only
Certificate No. MD00/3250/0005/6a Expiry date: 24/07/2018
2222-2, Sandae-RiAngang-OupKyungji-SiKyungbuAngang-eup
Angang Plant
Gyeongju-si, GyeongbukKyungju-Si, Kyungbuk
68.006061-T6, 6082-T6, 6063-T6* SeoulPlatesSHIN YANG METAL IND. CO., LTD9.006061-T6, 6082-T6, 6063-T6*Sections
Tel No: +82 31 363 1972 Fax No:+82 31 498 3300Email: [email protected]: www.shin-yang.comCertificate No: MD00/4455/0001/6a Expiry Date 27/03/2018
162 Sihwaro, Danwon-guAnsan-city Kyungki-go
6061, 6082, 6063* SeoulRefining & Semi FinishedSHIN YANG METAL IND. CO., LTD
Tel No: +82 31 491 3561 Fax No:+82 31 491 8800Email:Web:Certificate No: MD00/4455/0001/6a Expiry Date 27/03/2018
48, Wonsi-roDanwon-gu
BANWOL FACTORY
Ansan-city Gyeonggi-do
New Zealand
250.006061-T5, 6061-T6, 6082-T5, 6082-T6,6005A-T6, 6261-T6*, 6005A-T5,6261-T5*
AucklandExtrusionsULLEXCO
Tel: +64 (07) 849 5095 Fax: +64 (07) 849 4453 email: [email protected] web: www.ulrich-aluminium.co.nz* accepted for approved applications.Certificate Number: MD00/3071/0005/6a Expiry: 05/03/2019
Pukete Industrial EstateHamilton
A Division of Ullrich Aluminium39-45 Maui Street
As at 10 April 2018 14Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Norway
5083, 5086 OsloRefining & Semi FinishedALCOA NORWAY ANS
Tel: +47 751 79100 Fax: +47 751 71887
E-mail: [email protected]
Web: http://www.alcoa.com
Approval for semi finished products covers rolling ingots to 630mm max thickness, 2930mm max width and 8600mm max length.
Certificate No. MD00/3358/0004/6a Expiry date: 20/07/2019
Postboks 750, 8654 Mosjøen
305.00Al-Mg-Si grades OsloRefining & Semi FinishedBENTELER ALUMINIUM SYSTEMS NORWAY AS
Tel: +47 81 15 60 00 Fax: +47 61 15 94 87web: www.benteler.com
Certificate No: MD00/3995/0002/6a Expiry date: 19/10/2017
Cast House, Building 123,2830 Raufoss
Fabrikkveien
20.006005A-T4*, 6005A-T6, 6061-T6,6082-T4*, 6082-T6
OsloSectionsHYDAL ALUMINIUM PROFILER AS
Tel: +47 61 15 30 00 Mob: +47 95101796email [email protected] web: www.hydal.comCertificate No. MD00/3054/0008/6a Expiry date: 28/01/2019
Raufoss Industripark,Fabrikkveien, Bygn. No. 232 (vestsiden),N-2830 Raufoss
405.00Al-Mg-Si grades StavangerRefining & Semi FinishedHYDRO ALUMINIUM A.S. KARMØY
Tel no: +47 528 54380 Mob: +47 957 38463
E-mail [email protected]
Website: www.hydro.com
Certificate No: MD00/4328/0002/6a Expiry date 27/05/2020
Approval includes SFP ingot up to 405mm diameter x 7000mm in length
Mechanical testing out sourced
Hydroveien 1604265 HÅVIK
Poland
7.607022-T6 KatowiceForgings*ZAKLAD OBROBKI PLASTYCZNEJ Sp. z o.o.
Tel No: +48 81751 2600 Fax No: +48 81 4680911 Mob No: +48 602657609Email: [email protected]: www.kuznia-zop.plCertificate no: MD00/4313/0002/6a Expiry date: 30/04/2020*For Approved Applications
Raw material supply restricted to Grupa Kety SA.
ul. Kuznicza 1321- 045 Swidnik
South Africa
5083, 5086, 6061, 6082 DurbanRefining & Semi FinishedHULAMIN LIMITED25.005083-O, 5083-H116, 5083-H112,
5083-H321, 5086-O, 5086-H112,6061-T6, 6082-T6
Plates
30.005083-H111190.005083-O, 5086-O, 6061-T6, 6082-T6Sections
Tel: +33 396 6911 Fax +33 395 6469 Email mailto: [email protected] Web http://www.hulamin.co.zaCertificate No. MD00/3277/0007/6a Expiry: 11/10/2018
Moses Mabhida RoadPietermaritzburg
(Rolled Products)
3200
As at 10 April 2018 15Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Spain
100.00Al-Si7Mg BilbaoCastingsGRUPO ALUMINIOS DE PRECISION S.L.
Tel +34 947 297 481 Fax +34 947 297 484email: [email protected] web www.alu-gap.comCertificate No. MD00/4611/0001/6a Expiry date: 15/09/2019
Poligon Industrial VillalonquejarCalle Merindad de Cuesta Urria 2609001 Burgos
Sweden
30.006082-T6 GothenburgSectionsSAPA PROFILER AB70.006082-T6Bars
Tel: +46 (0)122 795090 Email: [email protected] Web:http://www.sapagroup.comCertificate No. MD00/1270/0007/6a Expiry date: 20/03/2018
Box 72S-612 22 Finspång
Al-Mg-Si grades GothenburgRefining & Semi FinishedSAPA PROFILER AB30.006082-T6Sections30.006082-T6Bars
Tel: +46 (0) 70 34 94 695 Fax: +46 383 94467 Email: [email protected] Web: http://www.sapagroup.com
Certificate Number: MD00/3422/0006/6a Expiry date: 28/01/2020
Approval covers for semi finished products as vertically cast ingots up to 317mm diameter and nominal 7000mm length supplied in the homogenised condition.
Approval for sections does not include closed profile sections.
Sjunnen Works SE-574 81SE- 57481 Vetlanda
Remelt / Press P2
Switzerland
307.003003* DortmundRefining & Semi FinishedALU MENZIKEN EXTRUSION AG30.003003-O*Extrusions
Tel: +41 62 765 29 07 Fax: +41 62 765 27 47Email :[email protected]: www.alu-menziken.comCertificate No. MD00/3325/0003/6a Expiry date: 10/03/2016
CH-5737 MenzikenHauptstrasse 35
Al-Mg grades, Al-Si grades HamburgRefining & Semi FinishedCONSTELLIUM VALAIS SA8.005083-H321, 5086-H321Plates
150.005083-O, 5083-H111, 5083-H112,5086-O, 5086-H111, 5086-H112,6061-T6, 6082-T6
600.005083-O, 5083-H111, 5083-H112,5086-O, 5086-H111, 5086-H112
Sections
720.006005A-T6, 6061-T6, 6082-T6600.005083-O, 5083-H111, 5083-H112,
5086-O, 5086-H111, 5086-H112Bars
720.006061-T6, 6082-T6
Tel: +41 27 457 68 40 Fax: +41 27 457 68 46 email: [email protected] web: www.constellium.com
Certificate No. MD00/2608/0007/6a Expiry date: 02/08/2020
PO BoxCH 3960 Sierre
As at 10 April 2018 16Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
Taiwan, Republic of China
5083, 5086, 5383 TaipeiRefining & Semi FinishedCHINA STEEL ALUMINIUM CORPORATION12.005083-O, 5083-H111, 5083-H116,
5083-H112, 5083-H321, 5383-O,5383-H111, 5383-H116, 5383-H321
Plates
50.005086-O, 5086-H111, 5086-H112,5086-H116
Tel: +886 7 871 8990 Fax: +886 7 872 1918Email: [email protected] page: www.csalu.com.tw Certificate No. MD00/4526/0001/6a Expiry date: 10/11/2018
Kaohsiung
The Netherlands
50.006005A-T6, 6061-T6, 6082-T6 Haren (Groningen)SectionsNEDAL ALUMINIUM B.V.50.006005A-T6, 6061-T6, 6082-T6Bars
Tel: +31 302925819 Mobile: +31 653516826 Email: [email protected]: www.nedal.nlCertificate No. MD00/3429/0004/6a Expiry date: 22/03/2018
P.O. Box 20203500 GA Utrecht
8.006005A-T6, 6082-T6 AmsterdamSectionsSAPA PROFILES NL BV
Tel: +31 - 341 - 464411
Certificate No.
3846 BB Harderwijk,Postbus 30,
Industrieweg 15,
3846 Harderwijk.
United Kingdom
63.006082-T6 Newcastle upon TyneExtrusionsSAPA PROFILES UK LTD
Tel: +44 (0)191 301 1226
E-mail: [email protected]
Website: www.sapagroup.com
Certificate No. MD00/3832/0004/6a Expiry date: 20/09/2019
Durham RoadBirtley
Birtley Plant
Chester-le-StreetCounty Durham, DH3 2AH
Al-Mg-Si grades BirminghamRefining & Semi FinishedSAPA PROFILES UK LTD.25.006005A-T5, 6005A-T6, 6061-T5,
6061-T6, 6082-T5, 6082-T6Sections
75.006005A-T5, 6005A-T6, 6061-T5,6061-T6, 6082-T5, 6082-T6
Bars
Tel: +44 1773 872761 Fax: 01773 874389 email: [email protected] web: www.sapagroup.com Certificate No. MD00/1261/0009/6a Expiry date: 06/09/2020
Sawpit LaneTibshelf
Tibshelf Plant
Derbyshire DE55 5NH
United States of America
1800.00Al-Si7Mg ChicagoCastingsA & B FOUNDRY AND MACHINING LLC.
Tel: +1 937-412-1900 Fax: +1 937-412-2998email: [email protected] web: www.abfoundry.comCertificate No: MD00/4090/0002/6a Expiry Date: 07/11/2018
835 N Main Street,Franklin,OH 45005,
As at 10 April 2018 17Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Max Thickness/Diameter(mm) OfficeName and Address Grades
List 6aApproved Refiners and Manufacturers of
Aluminium Alloy Plates, Sections , Bars, Castings & Forgings
Category
0.03Al-Si7Mg SeattleCastingsFREEMAN MARINE EQUIPMENT INC.
Tel: 1-888-FREEMAN, 1-888-373-3626, 1-541-247-7078 Fax: 1-541-2114
E-mail: [email protected]
Website: www.freemarine.com
Certificate No: MD00/4631/0001/6a Expiry Date: 20/11/2016
Gold Beach,Oregon 97444
28366 Hunter Creek Road,
73.00Al-Si7Mg Vancouver BCCastingsNU-CAST, INC.
Tel No +1 603 432 1600 Fax No +1 603 432 0724 Email [email protected] www. nu-cast.comCertificate No MD00/ 3986/ 0002/6a Expiry Date 07/02/2018
29, Grenier Field Road,Londonderry,NH 03053
As at 10 April 2018 18Page
In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.
© Lloyd’s Register Group Limited 2018. All rights reserved.
Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as ‘Lloyd's Register’. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. © Lloyd’s Register Group Limited 2018. All rights reserved.