Light Tape Design Guide

Light Tape is protected by U.S. Patent numbers 5,491,377 and 5,976,613 with other U.S. and worldwide Patents Pending

Prepare to be Illuminated!Imagine a light bulb you can bend around any surface for hundreds of feet, indoors or out. Its as thin as a credit card and costs a fraction of what other LED, fiber optics, neon, or fluorescent lighting systems cost to operate or maintain. Thats Light Tape!

Light Tape is the longest, thinnest, brightest and most durable electroluminescent light in the world. Combine Electro-LuminXs patented technology and manufacturing processes with the best materials available and you get Light Tape Lamps. We utilize Global Tungsten and Powders premium quality light emitting phosphors and Honeywells Aclam EL-100 Barrier Laminate to guarantee that we deliver the highest quality lamp possible to our customers.

Extremely Energy EfficientNot only is Light Tape easy to install, but its easy on the wallet. Our unique low energy design uses only 6 watts per square foot (0.5 watts per linear foot for 1 inch width) with even lumination.

Minimal Carbon Footprint!At an equal brightness of 140 cd/m, a 1 width strip of Light Tape

is 40% more efficient than LEDs, and our 1/2 Light Tape is 80% more efficient than LEDs. Expect to pay no more than $100 per year in operating costs. You can run 300 feet of Light Tape around your venue and only consume 100 watts.

Table of ContentsPage Subject

1 Introduction to Light Tape

2 Table of Contents

3 Exploded Side View of Light Tape

4 Standard Light Tape Colors in On/Off Positions

5 Light Tape Lamps Cut Sheet

6 Light Tape Panels and Shapes Cut Sheet

7 Light Tape Product Dimensions

8 Sealing Light Tape if Cut, Connecting Light

Tape

9 Connecting Multiple Segments of Light Tape

10 Mounting Guidelines, Noise Dampening and

Remote Power Supply Installation

11 Mounting Adhesives and Protective Sealants

12 Light Tape Installation Guidelines

13 Installing Corners or Bends

14 Outdoor Installation for Light Tape

15-17 Mounting Channel Installation

18 Floor Installation and Create Your Own

Light Box

19-20 Alternative Exterior Mounting Options

21-22 Light Tape Panel Installation - Interior

23 Light Tape Energy Consumption

24-26 Smart Driver Lighting Ballasts: AC Input

27 Smart Driver Lighting Ballasts: DC Input

28 Smart Driver Quick Guide

29 Safety and Hanging Guidelines

30 Light Tape Lifetime Guidelines

31-34 Light Tape Products and Services List

Transparent Electrode

Rear

Electrode

Dielectric

Alternating electrical current applied to the split electrode

Bring Your Imagination To Light With

R

R

Honeywell Aclam EL-100 Laminate Highest clear flexible moisture barrier in the world UL rated, self-extinguishing, anti-flammable shield Anti-graffiti protection, solvent resistant

Global Tungsten and Powders

premium quality light emitting phosphors and our patented technology, improving brightness and lifetime.

Copyright 2010, Electro-LuminX Lighting Corp, All Rights Reserved 3

Theres quite a bit happening inside our patented electroluminescent technology.

Theres quite a bit happening inside our patented electroluminescent technology.

www.lighttape.com

Thinner than a credit card (less than 0.02)!

Clear, crisp light that can be seen for miles!

We recommend Kodak glossy 7-mil polyester film for digital image backlighting. Provides a high image quality and robust handling properties Highest quality backlit solution in the market for thermal wide format printers utilizing dye inks. Incredible light transmission with a touch of diffusing resulting in the best white possible

Barrier Film

Barrier Film

Why Light Tape versus other EL? Proprietary manufacturing process chemically bonds layers. No more delaminating electrodes and shorts. Highly conductive rear electrode. Half the energy consumption of bus bar technology. Brightest phosphors available in our patented chemistry. Best barrier film in the world.

Classic Natural Blue

Classic Electric Blue

Extreme Green

Extreme International RedExtreme Rich Red

Extreme Kryptonite

Classic Media WhiteExtreme Blue-Green

Classic Pink Classic Yellow

Extreme Orange

X coordinate - 0.1684 Y coordinate - 0.3652




X coordinate -0.2526 Y coordinate - 0.3724

Extreme Caribbean Blue


Extreme Sky BlueClassic Purple


Light Tape is available in a variety of colors. Our base colors are Classic Natural Blue and Extreme Blue-Green. Please check our website for updated and new colors. Custom color matching is possible with minimum volume requirements.

*All colors are shown in Off/On positions*

Off On Off On Off On

NOTE: Colors may not appear as an exact match on screen or in print due to varying resolutions. Electro-LuminX is not responsible for variance in color from above to actual order. Samples are available to confirm color.

Normal Brightness Settings

Light Tape

Dimmable Continuous light for hundreds of feet with one connection Extremely energy efficient UV and moisture resistant for indoor or outdoor use Available in lengths up to 300 feet (see footage guide) Highly visible through smoke Thinner than a credit card Generates no heat, cool to touch Easy to install and maintain

0.25 Clear Barrier Encapsulation envelopes the illuminated

strip on all four sides

Illuminated Width

Lighting Ballast

AC or DC Input

Side View0.020 in./0.5mm

NOTE: Please see connector and lighting ballast information for further details on specifications

Light Tape Standard Widths

LT-025

LT-050

LT-100

LT-150

0.25

0.5

1

1.5

LT-200

LT-300

LT-400

LT-600

(19.05)

(25.4)

(38.1)

(50.7)

2

3

4

6

(63.5)

(88.9)

(114.3)

(165.1)

*Note: Illuminated Width in Inches (in Centimeters)

HOW TO ORDER LIGHT TAPE :Please specify Illuminated Width, Interior or Exterior, Classic or Extreme Series, Color, Length of Segment(s)

Example: 1 Indoor Extreme Orange Light Tape 20 feet long = LT100, INT, Extreme Orange, 1 in. @ 20 ft.

Light Tape Current Consumption

Light Tape Power Consumption

Power Source

Lamp Lifetime

27 cd/m (L), 125 cd/m (M), 200 cd/m (H) [candelas per meter]

0.30 to 0.90 milliamps per inch depending on service hours

Average of 0.5 watts per linear foot for 1 width based on brightness setting

AC or DC Input to ELLC Smart Driver Ballasts

Lifetime is 10,000 to 40,000 hours. See lifetime guideline on page 30


R

R


www.lighttape.com

Light Tape Linear Accent Lighting

Normal Brightness Settings 27 cd/m (L), 125 cd/m (M), 200 cd/m (H) [candelas per meter]

Light Tape Current Consumption 0.30 to 0.90 milliamps per inch depending on service hours

Light Tape Power Consumption Average of 0.5 watts per linear foot for 1 width based on brightness setting

Power Source AC or DC Input to E-LLC Smart Driver Ballasts

Lamp Lifetime Lifetime is 10,000 to 40,000 hours. See lifetime guideline on page 30

Smart DriverBy Electro-LuminX

Illuminate any size or shape per your specification! Perfect for backlighting onyx, acrylics, etc. Dimmable Extremely energy efficient, about 6 watts per square foot Even illumination, no hot or cold spots Thinner than a credit card Bendable, flexible, and rollable Easy to install and maintain Does not emit UV

0.25 Clear Barrier Encapsulation envelopes the illuminated panel on all four sides

Lighting Ballast

AC or DC Input Side View0.020 in./0.5mm

NOTE: Please see connector andlighting ballast information for furtherdetails on specifications

HOW TO ORDER LIGHT TAPE PANELS AND SHAPES:When ordering, please specify: Interior (INT) or Exterior (EXT) Installation Classic or Extreme Series Desired illuminated color Illuminated area (length x width) How long? Virtually any length How wide? Width up to 24 in 60 cm Can be tiled /joined together with ease to illuminate a large area without seams or gaps Power Input - AC or DC (110/220 V or 12/24 V are standard) Power input location (Please specify short or long side of lamp) Extended connection tabs may be specified. The standard length is 2 inches from end of panel to beginning of connector.

Normal Brightness Settings

Light Tape Current Consumption

Light Tape Power Consumption

Power Source

Lamp Lifetime

27 cd/m (L), 125 cd/m (M), 200 cd/m (H) [candelas per meter]

0.30 to 0.70 milliamps per inch depending on service hours

2.4 to 1 watt per square foot based on brightness setting

ELLC Smart Driver Ballasts - AC or DC Input

Average lifetime is 10,000 hours. See lifetime guideline on page 25

4,500 to 11,000 Kelvin, depending on operating frequencyLight Tape Color Temperature

Illuminated Area

Extended connection tabs to facilitate installation


Light Tape Backlighting

Light Tape Color Temperature 7500 Kelvin is standard. Warmer and cooler temperatures are available

Normal Brightness Settings 27 cd/m (L), 125 cd/m (M), 200 cd/m (H) [candelas per meter]

Light Tape Median Lux Rating 30 Lux (+/- 2) measured at 275 Volts (+/- 2%) and 650 Hz (+/- 5%)

Light Tape Current Consumption 0.30 to 0.90 milliamps per inch depending on service hours

Light Tape Power Consumption Average of 0.5 watts per linear foot for 1 width based on brightness setting

Power Source AC or DC Input to E-LLC Smart Driver Ballasts

Lamp Lifetime Lifetime is 10,000 to 40,000 hours. See lifetime guideline on page 30



Light Tape Product DimensionsAll products should be specified by the illuminated width, regardless of whether one specifies strips or panels. The protective Honeywell laminate extends past the illuminated area 0.25 to ensure encapsulation. Custom lamination widths are available (note B below) upon request.

Our base colors are Natural Blue and Extreme Blue-Green. We filter our natural colors to produce other colors. Our natural tapes after encapsulation are 0.02 (C) thick, but color filters add to the total thickness.

Top ViewA= Illuminated WidthB= Lamination Width

Side ViewD= Color Filter (will vary)

C= Light Tape with lamination

A B A B

0.25 0.75 6.35 mm 19.05 mm

0.5 1 12.7 mm 25.4 mm

1 1.5 25.4 mm 38.1 mm

1.5 2 38 mm 50.7 mm

2 2.5 50.8 mm 63.5 mm

3 3.5 76.2 mm 88.9 mm

4 4.5 101.6 mm 114.3 mm

6 6.5 152.4 mm 165.1 mm

ENGLISH METRIC

Light Tape Standard Widths

Light Tape/ThicknessC C & D

0.010 inch 0.020 - 0.022 inch


R

R

www.lighttape.com

1.28

1.880.58

Pierce the rear (grey side with white line) of the Light Tape with one connector pin on each side of the white line to create contact and electrical connection.

Fit connector caps to strainrelief and prepare adhesive to completely seal connection.

Firmly squeeze connector caps onto strain relief (we recommendwith vise grips) and complete withtwo locking screws.

Connector and Protective Cover Profiles

Heavy Duty Connector Easy two part system (as shown above) Designed for the highest IP enclosure rating possible. Water resistant Indoor/Outdoor

Light Duty Connector

Lower profile and less bulky Indoor Polycarbonate caps with protective insulation

0.75

1.44 0.25

18 AWG

2.88

0.63

0.56

18 AWG

1.75

0.63

0.16

Sealing Light Tape if Cut


Apply Edge Guard Sealant tape along cut edge and fold over cut edge.

Fold Edge Guardover to form a seal. Trim excess even with factory laminationwith scissors. On the non-connecting edge, leave 0.25" seal at end to prevent moisture from penetrating the lamp.

Please follow the below step-by-step instructions to ensure that Light Tape is cut and sealed properly.

Light Tape Indoor Connection Process

For outdoor applications, please refer to our outdoor epoxy connection guidelines.

The entire rear electrode of Light Tape is conductive. Unlike other antiquated technologies, you can make a connection anywhere and Light Tape will illuminate evenly. No need to worry about the electrode detaching from the Light Tape as you will find with bus bar technology.

Step 1: Step 2:

Width 0.25 inch 0.50 inch 1 inch 1.5 inch

Feet of LT

Width 2 inch 3 inch 4 inch 6 inch

Feet of LT

Connecting Multiple Light Tape SegmentsOnly one connection is required to power Light Tape , and there is no polarity. Terminating the other end is not necessary.Please see connection guide or our websites online video for How-To instructions.

It is possible to operate one lamp or multiple lamps with only one Smart Driver Power Supply. See Smart Driver information starting on page 24 to determine the appropriate power supply based on your installation.

Parallel

Connecting lamps in Parallel is the preferred method over connecting in series. Make all connections per local electrical codes. For remote locations and long runs, please use EMT conduit to shield AC signal.

SeriesWe DO NOT recommend connecting from one segment to the next in a Daisy Chain. Long runs in series or unbalanced loads can cause connectors to get hot due to resistance increasing from multiple connections. We recommend connecting in parallel.

Maximum Distance per Run with One Connection

Light Tape is capable of operating over great distances without any loss of light. The following chart outlinesrecommended single run footages with standard connectors. However, longer runs up to 300 feet are availableupon request with the addition of conductive foil tabs to the rear of Light Tape before factory encapsulation.

150 150 150 150

150 125 100 75



R

R

www.lighttape.com

ConductiveConnection Tabs

*Outdoor is available in 100 feet lengths in Snap-N-Light




If Light Tape is not secured or held in place, such as loose on a table, it will vibrate, producing a slight hum generally only audible in very quiet environments. We recommend firmly attaching the product or utilizing a backing buffer to reduceany noise.

Strips-- Ensure that the product is securely mounted to the surface. Loose lamps will produce a slight hum. However, 90% of the noise can be reduced if mounted properly. See our recommended mounting tapes. Panels-- It is possible to mount with VibraMount foam or other dampening material behind a panel to eliminate any noise. Again, make sure the panel is firmly secured in a frame or recommended system. The weight of the lens usually is all you need to dampen any noise. Power supply-- Generally, the power supply is located away from the lamp and is not an issue. A NEMA enclosure (see example and purchasing information below) can be used to reduce any harmonics emitted by the power supply.


Remote Power Supply InstallationSometimes, the power supply must be located far from the lamps. In this case, shielded conduit may be required to protect against high frequency and high voltage.

NEMA enclosure is required to store power supply when located outdoors. It is made of polycarbonate that is highly resistant to heat and natures elements. These enclosures can be found at http://www.automationdirect.com/enclosures. 50 foot connection radius-- it is possible to install the Light Tape up to 50 feet from the Smart Driver power source. Multiple connections are possible from one central location.

Electrical Metallic Tubing (EMT) conduit is required to shield the high voltage and high frequency AC signals for remote installations. All wiring should be within a conduit and 600 volt rated. Always follow all local electrical codes.

Smart Driver Lighting Ballasts

Input Voltage 90 - 265v 50/60 Hz. Output Voltage 200 - 350v Variable. Output Frequency 500 - 1000 Hz Variable. Output Power 500 W. Size 7 x 3 x 2 inches. Weight 3.25 lb /1.48 kg/49.4 oz. Mounting Enclosure has mounting flanges. RS232C based communication to Hand held unit.

There are a variety of models to choose from depending on desired usage. Each model has slightly different features based on popular customer requests. We will recommend the ideal lighting ballast depending on which key feature

Short circuit, over current, and other safety features built into design. External dimmer to adjust brightness. Micro Controller based Power Supply. Input voltage and frequency can be preset by a LCD based hand held unit. Warning message when frequency is being preset to higher ranges. Discrete blinking or blinking time can be set to various preset blinking rates. Designed to comply with CE, UL, & CSA norms.

Picture of supplies

Light Tape produces its unique glow when electricity is applied. Light Tape is able to accept AC or DC power inputs. Our Smart Driver Lighting Ballasts adjust voltage and frequency to illuminate the lamp in the most efficient way possible.

All you need to know is the total surface area of the lamps you wish to illuminate and the input voltage, AC or DC. From there, the rest is easy.

Smart Driver Lighting Ballasts: AC Input

Light Tape can be operated with standard batteries. With such a low current draw, it is a possible to achieve hours if not days of illumination with one charge. Our DC inverters are able to accept a variety of input voltages. However, our standard input is 12 volt unless otherwise specified. Alternate input voltages are available upon special request.

KEY FEATURES

Smart Driver Lighting Ballasts: DC Input

General Specifications

KEY FEATURES

Temp. Range: -30C to +85C High Efficiency Reverse Polarity Protection No Load Protection Short Circuit Protection Quiet operation Small form factor

Copyright 2007, all rights reserved www.lighttape.com 16

Smart Driver Outdoor Enclosures

If a Smart Driver Lighting Ballast is kept outdoors, it must be housed in protective enclosure. These enclosures are made of polycarbonate that is highly resistant to heat and natures elements. These enclosures can befound at http://www.automationdirect.com/enclosures.

Example of Outdoor Enclosure

50 feet maxfrom power

supply

Smart Driver

Light Tape Mounting GuidelinesIt is important to consider your environment when installing Light Tape. For example, it may be important to specify an outdoor barrier encapsulation for an indoor application.

A few quick rules: All outdoor installations must be in a mounting channel or approved system that allows Light Tape to expand, contract or "float" with weather (see Outdoor Mounting System on pages 14-17). Electrical connections should be in a J-box and wiring in conduit. Do not bend or kink Light Tape outdoors, straight runs only. When installed within public reach, it is recommended a protective lens or other cover Light Tape to prevent tampering. Do not use aggressive contracting adhesives to mount the Light Tape lamp. Please see our suggested products on the Mounting Adhesives and Sealants Section (page 11). Floors, wet locations, or high humidity areas require exterior barrier encapsulation, and factory seals are strongly recommended.

Noise Dampening

Light Tape Mounting Adhesives and Protective SealantsWe have a range of products that we recommend for mounting and protecting your Light Tape to ensure the longevity of the lamp.

Protective Sealants

Light Tape Edge Guard: A moisture resistant clear tape for interior applications to seal Light Tape to prevent shock when cut to length. Note: Light Tape must not be energized during the cutting step.

3M DP-100+ Epoxy: A two part epoxy system offering fast cure and machinabillity. It is easy mixing and meets UL 94. Perfect potting compound for outdoor connections.

Light Tape Shrink Tube: A heat-forming tube used in conjunction with our outdoor Snap-N-Light mounting system to form a moisture barrier and secure connector to channel.

Indoor Mounting Adhesives Light Tape VibraMount: Designed to secure Light Tape to almost any surface while eliminating vibration, VibraMount is a double sided adhesive, foam core tape, Clear core is available in 0.5" and 1", and black core 60 mil (1/16 / 1.6 mm) is available in widths up to 24" for large panel installations. Also, it provides impact resistance on uneven surfaces.

Light Tape DuraShield: Perfect for mounting Light Tape to smooth surfaces, such as windows, floors, painted surfaces, etc. Dura-Shield is a clear, non-yellowing, removable urethane film overlay that leaves no residue when removed. It is designed to provide a protective, puncture resistant shield to reduce abrasion while maintaining the low profile. It is available in 6 mil for average indoor applications, and 12 mil for high instance area installations.

Other adhesives: Light Tape weighs only 1/4 pound per square foot, aggressive adhesives are never necessary for installation. Velcro or various adhesive foam tapes work for many indoor applications. However, DO NOT use silicone, Liquid Nails, or other non-approved adhesives.

VibraMount

DuraShieldby Electro-LuminX



R

R

www.lighttape.com

Light Tape Installation Guidelines

Example of Outdoor Snap-N-Light: In this installation, we would begin by using three Smart Driver power supplies to balance the load (black connector boxes noted with Smart Driver logo).Tip: We recommend when operating multiple segments off one Smart Driver that the shortest segment is 50% of the mimimum rated load of the Smart Driver used.*For instance, the SD-4000 recommended operating range is 2000 to 4000 square inches. Therefore, the 50% threshold for the shortest segment would be 1000 square inches OR 2000 in x 0.50 = 1,000 square inches

Installing Light Tape is very straight forward. There are a few things to consider: Determine number of connections or segments of Light Tape per lighting design. (Consult chart on page 10 for maximum length per one connection). Assess power availability and source voltage (AC or DC). Determine power supply location. Mount per E-LLC recommended guidelines. Always protect Light Tape from tampering when accessible to the general public.


Order: 550 feet of 1 inch Exterior Extreme Rich Red Light Tape

Segments: 100 ft., 100 ft., 100 ft., 100 ft., and 150 ft. Snap-N-Light Power: two SD-4000s and one SD-2000

20

0 feet

100 feet

150 feet

10

0 feet

Smart Driver

Segment 2

Segm

ent 3

Segm

ent 1

Segment 4

= connector

=

Smart Driver

Smart Driver

SD-4000

SD-4000

SD-2000

10

0 feet

10

0 feet

Indoor:Light Tape should gently curve around bends and never be creased into a corner. Creating a bend or hard fold will damage the conductive coatings, leading to lamp failure.

Outdoor:DO NOT bend Light Tape around corners. Light Tape is subject to expansion and contraction. Please reconnect per outdoor connection procedure. Hard bends create pinch points, impeding movement.

Bend Radius:The bend radius recommended for a lateral curve is 30% of the length of the curve. Light Tape is to lay flat on the surface for the entire run. See below left illustration.

Installing Corners or Bends

3"

2"

Inner corner: Gently form into a curve in cornerwith finger.

Create a Curve: Form Light Tape into a soft bend. Do not flatten to create hard bend.

Outer Corner:If mounted within reach of general public or high abuse areas, please use extrusion to protect corner from impact.

124 (+/- 1)

20 12 +/- 1406 +/- 1

Each bend radius figure based on 2" Light Tape test standard. The thinner the width, the greater the bend.

The bend radius on a 180 curve should be no less than 1".



R

R

www.lighttape.com


Outdoor Mounting System - Snap-N- Light Our patented technology protects Global Tungsten and Powders' encapsulated phosphors from moisture and sunlight.

UV stable and non-fading colors

Light Tape is laminated in Aclam EL-100, the highest moisture barrier laminate in the world and made by Honeywell International, for the final layer of protection.

40% less energy consumption than LEDs.

Available in 100 foot lengths.

Weighs less than 1/4 pound per square foot.

Extremely visible through smoke, fog, haze, or snow.

Made of non-flammable and impact resistant materials

A

1/4 Lamp A = 0.9201/2 Lamp A = 1.170 1 Lamp A = 1.670 2 Lamp A = 2.670

0.1800.060 TYP

A

0.090 TYP

0.563 0.617

1/4 Lamp A = 1.1801/2 Lamp A = 1.420 1 Lamp A = 1.925 2 Lamp A = 2.925

Mounting Clip

Mounting Channel

Light Tape Mounting Channel SpecificationsMount-- Clip XXX

Mount-- Channel XXX Mount Clip and Mount Channel to fit Light Tape

025-- Light Tape

050-- Light Tape

100-- 1 Light Tape

200-- 2 Light Tape

Mount Clip is attached to mounting surface Mounting Channel holds the Light Tape and snaps into the pre-attached mounting clips.

Material Clear UV Stable Polycarbonate Mounting Channel

Mounting Screw Number 10

Clip Placement One clip per 1 to 3 feet, depending on surface

UV Screen Yes, and non-yellowing

Roll Format 100 foot coils - or longer per special order


Follow the below step-by-step outdoor mounting instructions to ensure that Light Tape is installed properly:

1. Clean the surface and mark a chalk line using a level. Mount clips on 12-36 centers, depending on surface, with number 10 screws. Mount with the first clip 1 from the connector end of the extrusion. If mounting indoors on smooth surfaces, mount UltraBond adhesive foam tape along the level line instead of clips.

Mounting Channel InstallationOur engineered mounting channels are designed to protect Light Tape from tampering and the outdoor environment. Constructed from high grade polycarbonate, they have tremendous impact resistance and weatherability. The snap-in mounting clips hold the mounting channel, and can be attached to almost any surface.

In order for our system to work for years, it is important that Light Tape is mounted properly. All outdoor installtions MUST be mounted into one of our mounting channels to allow the Light Tape to expand and contract with changes in the weather. Any Light Tape used in outdoor installations without mounting channels will void warranty.

* DO NOT bend Light Tape around corners when OUTSIDE. Pinch points can cause delamination. * All segments should be sealed per Electro-LuminXs procedure. We recommend factory seals for installations especially if poor drainage conditions exist. * Be sure to specify connection end - left or right side - so channel is pointing in the correct direction.

12 to 36" +/-

Level

DO NOT mount extrusion with silicone, Liquid Nails, or any non-approved adhesives which may come in contact with the Light Tape.

2. Drill weep holes on long runs of extrusion to allow for drainage. DO NOT fill open ends of the extrusion with silicone. If mounting with an adhesive do not block bottom gap.


R

R

www.lighttape.com

Bottom gap for drainage

4. Make sure you have a few inches for your connection once inside extrusion. We also recommend leaving about a 1/2" between connector and extrusion. The first clip, when ready to install, should begin at connector end.

"

1"


B. Feed Light Tape From End of Extrusion Ensure end of the extrusion is smooth. Adhere Light Tape to guide stick, it may be necessary to lubricate to ease entry. Slide down track slowly while feeding Light Tape. Utilize wheel or core to allow Light Tape to spin freely.

Stick opens slot if tight

3. Slip Light Tape into the Mounting Channel in from end or from the bottom and allow to drop in place. Make sure the slot in the channel is facing the structure and / or in the oppo-site direction of the light emitting side of the lamp!

A. Utilizing the Bottom Slot Slide the Light Tape upwards to the top of the channel. After clearing the lip, allow for Light Tape to rest in the channel. Do not force over the lip.

LIT SIDE

Important to leaveopen to allow for air flow

**IMPORTANT: DO NOT BEND, FLEX OR STRAIN LAMINATION WHEN PLACING LIGHT TAPE INTO EXTRUSION! It is important not to compromise edge seal.

*See demonstration video online for help if necessary. Please follow local electrical codes when making electrical connections and always use the Light Tape Outdoor Connection Kit.*


5. Take a 1/2 wide spacer or UltraBond gasket strip and wrap it around the Light Tape lamp between the connector cap and extrusion.

6. Starting with the end of the wire, slide the shrink tube over the entire length of the wire and connector. Be sure that the shrink tube is lined up with the second to last ridge of the strain relief, and is completely covering the connector, butyl gasket strip, and end of the extrusion (1/2" or more). Then, apply heat with a heat gun until a seal is formed around the extrusion and strain relief. Be careful not to overheat Light Tape.

7. Place connection in junction box and always follow local electrical codes.

UltraBond to provide seal and prevent chaffing.

End of extrusion

1 "

R

R

www.lighttape.com


8. Starting with the connected end, snap the Mounting Channel into the clips (slot on bottom rear). Be careful not to bend or kink the Light Tape when snapping into place. Be sure that bottom rear slit AND end of extrusion both are not covered or sealed, especially when using UltraBond to mount. This allows for proper air flow and drainage.

1. Slide into the top end of the clip first.

2. Press firmly down-ward to snap in place, making sure that slit in back is not covered to allow for drainage.

Surface Mount Suspended Mount Flush Mount

Surface

Sealant

Lens

Open to drain Screw and spacer

Surface Lens

Screw and spacer

Surface

Lens

Clip

Sealant

Bottom Layer Dampening Layer

Light Tape Layer

Digital Image Layer

Screw and spacer

Create Your Own Backlit SystemIt is possible to construct your own light box or mounting channel for larger format installations.

Clear Diffuser Layer

Rear surface isinert material thatdoes not absorbmoisture and lowexpansion

Optional noise dampening placedbehind the LightTape to eliminateany vibration

Light Tape is placed directly on top of the backingand may be adheredto the surface

Digital image should be placed directly on top ofthe Light Tape forbest results (optional)

0.02 thick clear plastic film to diffuse light from center line (optional)

It is importantthat Light Tapeis covered to prevent tampering.

Alternative Mounting for Exterior Installations Surface mount-- Light Tape is placed on mounting surface and then covered by a plastic lens Flush mount-- Surface is routed or pre-prepared to accept mounting channel with Light Tape Complete mount-- Light Tape is placed between two pieces of medium with one being clear

PLACE SPACERS BETWEEN THE FRONT AND REAR LAYER TO ALLOW FOR MOVEMENT

Ideal for suspending Light Tape awayfrom surface. Recommended if surface issusceptible to extreme heat, such as metalsAlso, ideal for large format graphics.

Light Tape is placed inside a track orchannel which has been cut in the existingsurface. A lens is then placed to protectfrom impact and is sealed on the top side.

Light Tape is sandwiched between theexisting structure and the protective cover. The top is sealed and the bottomis left open as a drain.

Front View

By sandwiching Light Tape in a frame, thelamp is able to expand and contract with theweather. The top and sides should be sealed and the bottom is open for drainage.

Onyx, Acrylic, Etc.

It is important that Light Tape is covered to prevent tampering.

Digital image should be placed directly on top of the Light Tape for best results(Optional).

0.02" thick clear plastic film to diffuse light from center line (optional).

Light Tape is placed directly on top of the backing and may be adhered to the surface.

A dampening layer may be utilized to reduce vibration.

Rear surface is inert material that does not absorb moisture and low expansion.

NO MORE BULKY LIGHT BOXES! BACKLIGHT IMAGES EASILY AND LESS THAN 0.25 THICK!


Permanent Flush Mount

Protective cover

Temporary Mount

Light Tape VibraMount Foam +/- 0.06

DuraShield

Floor InstallationLight Tape has tremendous impact resistance properties which makes it difficult to damage. However, it is important to protect Light Tape from abrasion, which can damage the barrier lamination.

Ideally, floor is designed with channels to place Light Tape . A protective cover, which can be made of glass, polycarbonate, etc., should be sealed around the edge to prevent moisture from entering. Factorysealed exterior lamination and exterior connectionsare required to protect the Light Tape . Drain may be required in wet environments.

Light Tape may be placed on smooth surfaces andthen covered with our DuraShield to protect the product from general foot traffic. Rougher surfaces may require VibraMount foam for impact resistance. Again, factory sealed exterior lamination and exteriorconnections are required.

Copyright 2007, all rights reserved www.lighttape.com 14

Light Tape

VibraMount Foam

Light TapeExtrusion

Drain

Light Tape Mounting Channel is placed in prepared track which should be sloped slightly to allow for drainage. Factory sealed exterior lamination and exterior connections are necessary.

Permanent Flush Mount with Mounting Channel

Floor/Surface

Floor/Surface

Floor/Surface

Drain

Less than 0.25 thick (12mm)!


Follow the below steps to properly construct your light box to ensure the life of your Light Tape. Choose an appropriate mount based on the conditions in which the light box will be placed.

1. Clean surface. It is important that surface is smooth.

2. Sandwich Light Tape between the surface and the lens, placing a spacer behind the lens. It is recommended that Light Tape VibraMount or other compressible material is placed behind Light Tape. Note: Only adhere foam to surface and not to Light Tape to allow for expansion and contraction.

3. Screw lens to surface. Apply slight pressure so panel is lightly pressed between the lens and backing on surface.

4. Seal the mount together at the top and sides. Leave a gap or holes at bottom to allow for drainage.

Front ViewBy sandwiching Light Tape in a frame, thelamp is able to expand and contract with theweather. The top and sides should be sealed and the bottom is open for drainage.


Surface

Sealant

Lens


Surface Lens

Screw and spacer

Surface

Lens

Clip

Sealant

Screw and spacer


Ideal for suspending Light Tape awayfrom surface. Recommended if surface issusceptible to extreme heat, such as metals.



Alternative Mounting for Exterior Installations Surface Mount- Light Tape is placed on mounting surface and then covered by a plastic lens. Surface mounts are ideal for wood, concrete, brick and other surfaces that DO NOT conduct heat. Flush Mount- Surface is routed or pre-prepared to accept mounting channel with Light Tape. Flush mounts are ideal for wood, concrete, brick and other surfaces that DO NOT conduct heat. Suspended Mount- Light Tape is placed between two pieces of medium with one being clear. Suspended Mounts are ideal for metallic and other heat conducting surfaces, as it offsets air flow.


Surface

Sealant

Lens


Surface Lens

Screw and spacer

Surface

Lens

Clip

Sealant

Bottom Layer Dampening Layer

Light Tape Layer

Digital Image Layer

Screw and spacer

Create Your Own Light BoxIt is possible to construct your own light box or mounting channel for larger format installations.

Clear Diffuser Layer

Rear surface isinert material thatdoes not absorbmoisture and lowexpansion

Optional noise dampening placedbehind the LightTape to eliminateany vibration

Light Tape is placed directly on top of the backingand may be adheredto the surface

Digital image should be placed directly on top ofthe Light Tape forbest results

0.02 thick clear plastic film to diffuse light from center line (optional)

It is importantthat Light Tapeis covered toprevent tamp-ering.

Alternative Mounting for Exterior Installations Surface mount-- Light Tape is placed on mounting surface and then covered by a plastic lens Flush mount-- Surface is routed or pre-prepared to accept mounting channel with Light Tape Complete mount-- Light Tape is placed between two pieces of medium with one being clear


Ideal for suspending Light Tape awayfrom surface. Recommended if surface issusceptible to extreme heat, such as metalsAlso, ideal for large format graphics.



Front View

By sandwiching Light Tape in a frame, thelamp is able to expand and contract with theweather. The top and sides should be sealed and the bottom is open for drainage.

Clear Plastic Top Layer

PLACE SPACERS BETWEEN THE FRONT AND REAR LAYER TO ALLOW FOR SLIGHT MOVEMENT!

Note: For ALL mounts, by sandwiching Light Tape in a frame, the lamp is able to expand and contract with the weather. The top and sides should be sealed and the bottom is open for drainage.


R

R

www.lighttape.com


1. Utilize smooth materials to construct lenses.

2. Sandwich Light Tape between two plastic lenses with spacers separating the Light Tape from the lenses. Apply slight pressure so that panel is lightly pressed between the lenses.

3. Screw mount to surface.

4. Seal the mount together at the top and sides. Leave a gap or holes at bottom of the sign to allow for drainage.



Surface

Sealant

Lens


Surface Lens

Screw and spacer

Surface

Lens

Clip

Sealant

Screw and spacer







Surface

Sealant

Lens


Surface Lens

Screw and spacer

Surface

Lens

Clip

Sealant

Screw and spacer





1. Cut track or channel in existing surface.

2. Clean surface. It is important that surface is smooth.

3. Sandwich Light Tape between the surface and the lens, placing a spacer behind the lens. It is recommended that Light Tape VibraMount or other compressible material is placed behind Light Tape. Note: Only adhere foam to surface and not to Light Tape to allow for expansion and contraction.

4. Screw lens to surface. Apply slight pressure so panel is lightly pressed between the lens and backing on surface.

5. Seal the mount together at the top and sides. Leave a gap or holes at bottom of the sign to allow for drainage.

It is important to remember a few things when installing large Light Tape panels:

Do not kink or fold the Light Tape panel Do not crease or fold conductive electrodes Plan ahead. If you are mounting indoors with an adhesive, you only get one chance!

1. Clean surface with isopropyl alcohol. Surface should be smooth.

2. Determine where you will make the electrical connection. It is important to consider the connector and cap. The conductive electrodes can be guided behind the panel. We recommend all electrical connections are made in a junction box. 3. Mounting surface can vary depending on installation. When positive, mount in a manner that allows panel to be changed in years to come (i.e. wall studs behind sheet rock wall). Tip: Mounting to removable sheet rock panel works well with VibraMount.

4. Adhesive Mounting: We recommend using our VibraMount adhesive as a backing when indoors. Customers have also had success with industrial velcro.

Place adhesive on wall, trim to size if needed, and remove liner.

5. Hide connector: The conductive electrodes are basically flat wires. Be careful not to rip the surrounding lamination. However, lamination may be trimmed to form a tail.

Conductive electrode Conductive electrodes tail and connector tail are fed through wall. feed into junction box for connection.


Light Tape Panel Installation - Indoor

Removable Panel

Sheet Rock

VibraMount

Sheet Rock

TM

Smart Driver

DO NOT TEAR!


R

R

www.lighttape.com

Cut an access point if mounting surface is not removable.

6. Applying Light Tape: Take your time. Once Light Tape has been applied, pulling it off of the surface will damage the lamp. For larger panels, it is easier to unroll the Light Tape into place.

When bending conductive electrodes to hide connector tail behind lamp, place a strip of VibraMount adhesive foam at the bend to prevent creasing.


Tab

Connector lead - feed through slot cut in wall. Be careful not to kink or fold conductive tabs.

Mounting surface

Unrolling the Light Tape Begin with connector end. Make sure the leading edge is square. Then slowly unroll the Light Tape, in

this case left to right.

Flip Into PlaceLine up bottom edge and lift panel into place. You may need two people to ensure Light Tape goes on evenly

without waves or ripples.

Mounting surface

Light Tape

VibraMount strip or other compressable material the diameter of a pencil to prevent a hard fold.

Unroll

90

Side View


Light Tape Energy ConsumptionLight Tape is the most inexpensive, energy efficient lighting option available, costing only about $80 a year. Compared to fluorescent and neon lighting, both costing about $1700 annually, Light Tape is a bargain! Even LEDs, the energy efficient choice, costs about $500 a year to operate.

Light Tape Energy Consumption

Light Tape Energy Consumption By Area Light Tape Energy Consumption

Watts per Square Foot Amps per Area with Full Illumination

Brightness

Light Tape Energy Consumption By Standard Sizes Watts

Watts Area6.5 watts 1 Square Foot13 watts 2 Square Feet

19.4 watts 3 Square Feet25.9 watts 4 Square Feet32.4 watts 5 Square Feet38.9 watts 6 Square Feet45.4 watts 7 Square Feet51.8 watts 8 Square Feet58.3 watts 9 Square Feet64.8 watts 10 Square Feet

Print Size Amps Area1 in 0.00025 1 inA4 0.023 94 inA3 0.468 187 inA2 0.102 408 inA1 0.216 864 inA0 0.387 1549 in

11 x 11.5 0.032 126.5 in16 x 16.5 0.066 264 in

30 foot lamberts102.6 cd/m

Print Size Full Illumination 50% Illumination Units1 in 0.45 0.225 wattsA4 4.355 2.1775 wattsA3 8.71 4.355 wattsA2 16.9 8.45 wattsA1 34.97 17.485 wattsA0 69.94 34.97 watts

11 x 11.5 5.72 2.86 watts16 x 16.5 11.895 5.9475 watts

Light Tape Comparative Data900800700600500400300200100

0Operating Cost/Year at 150 sq. ft. (Estimated at $0.15/kwH)

Light Tape Neon Fiberoptics LED Fluorescent


R

R

www.lighttape.com

Smart Driver Lighting Ballasts: AC Input (110/220 V)


Smart Driver Lighting Ballasts are engineered to illuminate Light Tape. Whether it is one piece or ten, it is possible to do it all with one ballast. Our Smart Driver Lighting Ballasts adjust voltage and frequency to illuminate Light Tape in the most efficient way. All you need to know is the total surface area of the Light Tape you wish to illuminate to determine the proper ballast!


Intelligent Electroluminescent Power Source

Features Rated Input Voltage 110 / 220 VAC

Protection Class 1 IP Degree 2x

Very low audible noise Worldwide voltage capacity

Blink switch Visual LED system status indicator

Stylish compact design Light weight

Short circuit and overload protection Convection Air Cooled

Designed to comply with CE, UL, and CSA norms

1. Input Voltage Selector (110V or 220V)2. Green LED - Normal Operating Conditions3. Red LED - Overload Condition or Short Circuit4. Lighting Ballast Operation Switch (Blink-On-Off)5. Brightness Adjustment Knob6. Output Wires7. Power Switch (On / Off)8. Spare Fuse9. Power Cord Input

Model Lamp Area Rated Input Current Dimensions Weight

SD-50 36-50 sq. in. 0.2 Amps 3.5" x 3.31" x 1.88" 0.65 lbs / 0.3 kg

SD-150 75-175 sq. in. 0.25 Amps 3.5" x 3.31" x 1.88" 0.65 lbs / 0.3 kg

SD-400 200-400 sq. in 0.8 min / 2.5 max Amps 6.81 x 2.86 x 1.85 1.4 lbs / 0.64 kg

SD-1000 450-1000 sq. in. 0.45 / 0.70 Amps 6.19 x 4.12 x 2.25 1.95 lbs / 0.88 kg

SD-2000 1000-2100 sq. in 0.12 / 2.25 Amps 4.86 x 4.17 x 2.25 1.85 lbs / 0.84 kg

SD-4000 2100-4700 sq. in. 0.42 / 3.30 Amps 6.94 x 4.17 x 2.25 3 lbs / 1.36 kg

SD-8000 4700-8000 sq. in. 0.80 / 4.50 Amps 8.94 x 4.17 x 2.27 3.5 lbs / 1.59 kg

There are a variety of models to choose from, depending on desired usage.Each model has slightly different features based on popular customer requests. We will recommend the ideal lighting ballast, depending on whichkey feature is most important. A factory representative should advise a model if the lamp area is on the lower or upper end of the range.Light Tape Comparative Data

Rated Input Voltage 120 or 240 VAC

Rated Input Current 0.8 min / 2.5 max Amps

Rated Input Frequency 50 Hz/60 Hz

Rated Output Voltage* 200 to 300 VA

Rated Output Frequency 500 to 800 Hz

Lamp Area 200-400 Sq. In.

Short Circuit Lamp Protection, Input Power Status LED and Lamp Status LED

Provided

AC Ballast Specifications: SD-400

Smart Driver Lighting Ballasts: AC Specifications


*Factory Rated Output Voltage. Smart Driver can operate outside of rated output range.

A few guidelines to remember about your Smart Driver Lighting Ballast: It is important that you operate Light Tape and Smart Driver Lighting Ballasts within their parameters. Over current will destroy electrical connections. 250 volts is mid range and recommended set point! The external dimmer switch on Smart Driver controls the output voltage and frequency. Use a voltage meter to determine volts / hertz from Smart Driver to Light Tape. Always set power supply output voltage per factory recommended setting: Low: 200 volts; Medium: 250 volts; High: 300 volts We DO NOT recommend exceeding 300 volts. Contact E-LLC if Smart Driver is operating outside of range. Red LED indicates the following: 1. Short Circuit Protection: Check wiring if light is on. 2. Overload Protection: Verify that lamp area is acceptable, or for possible damage to lamp. Always treat Light Tape and Smart Driver with care and respect as one would with any device where electrical current is present.

AC Ballast Specifications: SD-50/SD-150

Rated Input Voltage Select one: 120 or 240 VAC

Rated Input Current SD-50 0.20 Amps SD-150 0.25 Amps

Rated Input Frequency 50 Hz/60 Hz 50 Hz/60Hz

Rated Output Voltage* 200 to 300 VAC


Lamp Area 36-50 Sq. In./75-175 Sq. In.


Provided


R

R

www.lighttape.com

Rated Input Voltage 120 VAC 240 VAC

Rated Input Current 0.42 Amps 3.30 Amps





Lamp Area 2100 to 4700 Sq. In.Short Circuit Lamp Protection, Input Power Status LED and Lamp Status LED

Provided

Rated Input Voltage 120 VAC 240 VAC

Rated Input Current 0.80 Amps 4.50 Amps





Lamp Area 4700 to 8000 Sq. In.


Provided


*Factory Rated Output Voltage. Smart Driver can operate outside of rated output range.

Rated Input Voltage 120 VAC 240 VACRated Input Current 0.12 Amps 2.25 Amps



Rated Output Voltage* 200 to 300 VACRated Output Frequency 500 to 800 HzLamp Area 1000 to 2100 Sq. In.Short Circuit Lamp Protection, Input Power Status LED and Lamp Status LED

Provided

Rated Input Voltage 120 VAC 240 VACRated Input Current 0.45 Amps 0.70 AmpsRated Input Frequency 50 Hz/60 Hz 50 Hz/60Hz


Rated Output Voltage* 200 to 300 VACRated Output Frequency 500 to 800 HzLamp Area 450 to 1000 Sq. In.Short Circuit Lamp Protection, Input Power Status LED and Lamp Status LED

Provided

Smart Driver Lighting Ballasts: DC Input

Light Tape can be operated with standardbatteries. With such a low current draw, itis possible to achieve hours, if not days, of illumination with one charge. Our DC inver-ters are able to accept a variety of input voltages. However, our standard input is 12 volt unless otherwise specified. Alternate input voltages (3 vdc, 6 vdc, 9 vdc, and 24 vdc) are available upon special request for quantities of 250 or more.

Copyright 2010, Electro-LuminX Lighting Corp, All Rights Reserved

Smart Driver Lighting Ballasts are engineered to illuminate Light Tape. Whether it is one lamp or ten, it is possible to do it all with one ballast. Compact sizing makes DC power supplies ideal for specific applications. All you need to know is the total surface area of the Light Tape you wish to illuminate!


Intelligent Electroluminescent Power Source

Features Mountable or Portable

Compact in size Standard with mounting platform, but can be ordered without based on quantity order

Temperature range: -30C to +85C High Efficiency

Reverse Polarity Protection No Load Protection

Short Circuit Protection Self Compensating

Quiet Operation Small Form Factor

CE compliant

Pictured above: DC-100P, Below: DC-100

Model Lamp Area Input ~ mA Output ~ mA Dimensions Weight

9V 1-33 sq. in. 144 48 2.31" x 2.31" x 0.94" 0.15 lb / 2.4 oz

DC-20P 1-20 sq. in. 88 29 1.75" x 1.08" x 0.79" 0.1 lb / 1.6 oz

DC-50P 20-50 sq. in. 219 73 2.9" x 1.55" x 1" 0.2 lb / 3.2 oz

DC-100P 50-100 sq. in. 438 146 2.87" x 2" x 1.47" 0.45 lb / 7.2 oz

DC-150 50-150 sq. in. 656 219 3.88" x 2.08" x 1.5" 0.6 lb / 9.6 oz

DC-500 100-500 sq. in. 2188 729 5.14" x 2.33 x 1.74" 1.85 lbs / 29.6 oz

SD-1800 (24V) 600-1800 sq. in. 7875 2625 6.19" x 3.94" x 2.07" 2.4 lbs / 38.4 oz


R

R

www.lighttape.com


Lighting Ballast Sizing Guidelines Smart Driver Lighting Ballasts are designed to illuminate specific surface areas. Light Tape will achieve maximum performance and lifetime by selecting the appropriate ballast to supply power to the application. All you need to do is determine the total surface area of Light Tape that you are using for your installation. Refer to the following Quick Guide to determine which power supply is suitable. A factory representative should advise a model if the lamp area is on the lower or upper end of the range.

We recommend when operating multiple segments off one Smart Driver that the shortest segment is 50% of the mimimum rated load. For instance, the SD-4000 recommended operating range is 2000 to 4000 square inches. Therefore, the 50% threshold for the shortest segment would be 1000 square inches. If one segment of the installa-tion goes out, please balance the load. Prolonged use with an unbalanced load may result in failure at connection.

Smart Driver Quick Guide (English: Square Inches / Metric: Square Centimeters)

Width: Inches/Centimeters

Length: Feet/

Meters

30/194 60/387 120/774 180/1161 240/1548 360/2323 480/3097 720/4645

60/197 120/774 240/1548 360/2323 480/3097 720/4645 960/6194 1440/9290

90/581 180/1161 360/2323 480/3484 720/4645 1080/6968 1440/9290 2160/13935

120/774 240/1548 480/3097 720/4645 960/6194 1440/9290 1920/12387 2880/18581

150/968 300/1935 600/3871 900/5806 1200/7742 1880/11613 2400/15484 3600/23226

180/1161 360/2323 720/4645 1080/6968 1440/9290 2160/13935 2880/18581 4320/27871

210/1355 420/2710 840/5419 1260/8129 1680/10839 2520/16258 3360/21677 5040/32516

240/1548 480/3097 960/6194 1440/9290 1920/12387 2880/18581 3840/24744 5760/37161

270/1742 540/3484 1080/6968 1620/10452 2160/13935 3240/20903 4320/27871 6480/41806

300/1935 600/3871 1200/7742 1800/11613 2400/15484 3600/23226 4800/30968 7200/46452

375/2419 750/4839 1500/9677 2250/14516 3000/19355 4500/29032 6000/38710 9000/58064

450/2309 900/5806 1800/11613 2400/17419 3600/23266 5400/34839 7200/46452 10800/69677

525/3387 1050/6774 2100/13548 3150/20323 4200/27097 6300/40645 8400/54193 12600/81290

600/3871 1200/7742 2400/15484 3600/23226 4800/30968 7200/46452 9600/61935 14400/92903

675/4355 1350/8710 2700/17419 4050/26129 5400/34839 8100/52258 10800/69677 16200/104516

750/4839 1500/9677 3000/19355 4500/29032 6000/38710 9000/58064 12000/77419 18000/116129

825/5323 1650/10645 3300/21290 4950/31935 6600/42581 9900/63871 13200/85161 19800/127742

900/5806 1800/11613 3600/23226 5400/34839 7200/46452 10800/69677 14400/92903 21600/139355

10'/3m

20'/6m

30'/9m

40'/12m

50'/15m

60'/18m

70'/21m

80'/24m

90'/27m

100'/30m

125'/38m

150'/45m

175'/53m

200'/61m

225'/70m

250'/76m

275'/84m

300'/94m

0.25"/0.635 cm 0.5"/1.27cm 1"/2.54 cm 1.5"/3.8 cm 2"/5.08 cm 3"/7.52 cm 4"/10.16 cm 6"/15.24 cm

Recommended Ballastper Range:

PS-SD-50

PS-SD-150

PS-SD-400

PS-SD-1000

PS-SD-2000

PS-SD-4000

PS-SD-8000

Over range for one ballast


Safety and Handling Guidelines for Light Tape

NEVER operate Light Tape when in a coil. Unroll first before powering.

Always consult local electrical codes for wiring or other specifications and regulations.

Take care to mount the Light Tape out of reach of children or malicious individuals.

Always seal Light Tape if cut with Light Tape Edge Guard.

Do not step on Light Tape during installation. Avoid hard creases.

Do install in dry conditions. Do not cut or expose open ends to moisture.

Do not break lamination when pulling around sharp edges or corners.

Do not use a screwdriver or sharp object to force lamp into tight areas.

Do not fold, twist, rotate or kink lamination excessively.

Do not stretch, puncture or crease Light Tape, as it will destroy conductive layers causing black spots or failure.

Do not operate lamp outdoors during peak daylight hours due to harmful UV rays.

Do use for a photo-cell outdoor installation, to prevent the Light Tape from operating in peak daylight hours due to harmful UV rays.

Do not operate Light Tape without protective lamination.

Do follow all installation guidelines from Electro-LuminX. If there are any questions, check our web site, www.lighttape.com.

Do not thermoform or stretch Light Tape over objects, or bend Light Tape in a tight radius.

When cleaning Light Tape or Smart Driver Lighting Ballasts, do not use water or chemical cleanser.

Do not operate Smart Driver Lighting Ballasts outdoors unless in a NEMA enclosure.

In industrial applications, use caution when operating Smart Driver Lighting Ballasts as they have not been explosion-proof rated by the National Electrical Code (USA, Central and South America), Canadian Standards Association, International Electrotechnical Commission (ATEX - Europe and outside Americas), and Gosstandart (Russia).


R

R

www.lighttape.com

Brightness** 27 candela/m - 8 foot lamberts

Life Expectancy* 20,000 to 40,000 hours**

Continuous 5 to 10 years

Flashing 9 to 20 years

Operating Parameters 200 volts

Brightness** 100 candela/m - 30 foot lamberts

Life Expectancy* 10,000 - 20,000 hours**

Continuous 3 to 5 years

Flashing 6 to 14 years


Brightness** 200 candelas/m - 60 foot lamberts

Life Expectancy* 3,000 - 5,000 hours**

Continuous 6 to 18 months

Flashing 12 to 36 months



Light Tape Lifetime GuidelinesLight Tape is essentially a flat light bulb utilizing phosphors as a light source similar to Plasma televisions. The brightness of the lamp is directly correlated to the amount of current supplied to illuminate the lamp. The lower the brightness or current, the longer the phosphor lifetime. Adjusting the brightness will alter the lifetime curve. Other options, such as flashing, will double the useful life.

To optimize the illumination versus lifetime balance, it is important to consider the ambient light of your venue. The appropriate illumination effect should be determined on a per application basis. We can preset power supplies or adjustments can be made on-site to match customer requirements.

* Life expectancy based on operating Light Tape 8 hours per day. ** Range varies based on phosphor type, i.e. Natural vs. Extreme SeriesNote: Standard brightness and factory setting unless specified


Light Tape Product and Services ListITEM DESCRIPTION

CONNECTING: C-Black Rubber Black Rubber for 0.25 in. and 0.50 in. Connectors

CONNECTING: C-Co-Foil Connection Tabs, 0.5 in., 1 ft.CONNECTING: C-Ecto, Connector # Pairs (pair=2 ectos)

CONNECTING: C-Hot Glue Custom Low Profile Light Tape ConnectionCONNECTING: C-Junction Box Quick Disconnect Junction Box for X Outputs (NOT water resistant)

CONNECTING: C-LT, Connection Custom Light Tape Connection

CONNECTING: C-LT, Connection (First) Custom Light Tape Connection

CONNECTING: C-LT, Connection (Panel)Custom Light Tape Connection for panels - 2 in. tab to allow connector to be hidden.

CONNECTING: C-LT, Connection (Quick) Quick Connector Plug-in TypeCONNECTING: C-LT, Connector (Large) Connector for 0.50 in. & WiderCONNECTING: C-LT, Connector (Low Profile) Clear, Low Profile ConnectorCONNECTING: C-LT, Connector (Small) Connector for 0.25 in.

CONNECTING: C:Nic, Connector # Pairs (pair=4 nics)

CONNECTING: C-Tyco, Connector Quick Disconnects - 600 Volt Tyco Connectors

CONNECTING: Connector Gasket Low Profile Connector FoamCONNECTING: Seal-End Seal Tape 1.0 in. End Seal Tape, 1 in., 5 ft.CONNECTING: Seal-End Seal Tape Special End Seal Tape # in., #in., (# ft.)

CONNECTING: Seal-Star BriteStar Brite is required during exterior installations for sealing all cut ends of Light Tape.

CONNECTING: Wire-18 Gauge Nonpolar WireTyco Connectors: Female Connector 1586017-2 02P FH Plughsg 4.2MMTyco Connectors: Female Pin 794955-1 4.2MM Pin Tin

Tyco Connectors: Male Connector 1586019-2 02P RCPT HG 4.2 MM

Tyco Connectors: Male Pin 794956-1 4.2MM Socket Tin

LIGHT TAPE PANELS: P-Custom EXT, ColorExterior, Color, # Piece(s), # in., LIT AREA, Add 0.25 in. to each side for finished area, Power short side

LIGHT TAPE PANELS: P-Custom EXT, Natural BlueExterior, Natural Blue, # Piece(s), # in., LIT AREA, Add 0.25 in. to each side for finished area, Power short side

LIGHT TAPE PANELS: P-Custom INT, ColorInterior, Color, # Piece(s), # in., LIT AREA, Add 0.25 in. to each side for finished area, Power short side

LIGHT TAPE PANELS: P-Custom, INT, Natural BlueInterior, Natural Blue, # Piece(s), # in., LIT AREA, Add 0.25 in. to each side for finished area, Power short side

LIGHT TAPE PANELS: P A1 INT, 24 in. x 36 in. Interior, Color, 24 in. x 36 in., Finished, Power 17 in. SideLIGHT TAPE PANELS: P A2 INT, 15.75 in. x 23.62 in. Interior, Color, 15.75 in. x 23.62 in., Finished, Power 17 in. Side

LIGHT TAPE PANELS: P A3 INT, 11.81 in. x 15.75 in. Interior, Color, 11.81 in. x 15.75 in., Finished, Power 11 in. Side

LIGHT TAPE PANELS: P A4 INT, 7.87 in. x 11.81 in. Interior, Color, 7.87 in. x 11.81 in., Finished, Power 8.5 in. Side

LIGHT TAPE STRIPS: LT-EXT, COLOR:025 EXT, Color Exterior, Color, # Piece(s), 0.25 in., # ft., Seal / Cut


R

R

www.lighttape.com

ITEM DESCRIPTIONLIGHT TAPE STRIPS: LT-EXT, COLOR:050 EXT, Color Exterior, Color, # Piece(s), 0.50 in., # ft., Seal / CutLIGHT TAPE STRIPS: LT-EXT, COLOR:100 EXT, Color Exterior, Color, # Piece(s), 1 in., # ft., Seal / CutLIGHT TAPE STRIPS: LT-EXT, COLOR:150 EXT, Color Exterior, Color, # Piece(s), 1.5 in., # ft., Seal / CutLIGHT TAPE STRIPS: LT-EXT, COLOR:200 EXT, Color Exterior, Color, # Piece(s), 2 in., # ft., Seal / Cut

LIGHT TAPE STRIPS: LT-EXT, COLOR:300 EXT, Color Exterior, Color, # Piece(s), 3 in., # ft., Seal / Cut



LIGHT TAPE STRIPS: LT-EXT, NATURAL BLUE:025 EXT, Natural Blue

Exterior, Natural Blue, # Piece(s), 0.25 in., # ft., Seal / Cut




Exterior, Natural Blue, # Piece(s), 1 in., # ft., Seal / Cut











LIGHT TAPE STRIPS: LT-INT, COLOR:025 INT, Color Interior, Color, # Piece(s), 0.25 in., # ft., CutLIGHT TAPE STRIPS: LT-INT, COLOR:050 INT, Color Interior, Color, # Piece(s), 0.5 in., # ft., CutLIGHT TAPE STRIPS: LT-INT, COLOR:100 INT, Color Interior, Color, # Piece(s), 1 in., # ft., CutLIGHT TAPE STRIPS: LT-INT, COLOR:150 INT, Color Interior, Color, # Piece(s), 1.5 in., # ft., CutLIGHT TAPE STRIPS: LT-INT, COLOR:200 INT, Color Interior, Color, # Piece(s), 2 in., # ft., Cut

LIGHT TAPE STRIPS: LT-INT, COLOR:300 INT, Color Interior, Color, # Piece(s), 3 in., # ft., Cut

LIGHT TAPE STRIPS: LT-INT, COLOR:400 INT, Color Interior, Color, # Piece(s), 4 in., # ft., CutLIGHT TAPE STRIPS: LT-INT, COLOR:600 INT, Color Interior, Color, # Piece(s), 6 in., # ft., CutLIGHT TAPE STRIPS: LT-INT, NATURAL BLUE:025 INT, Natural Blue

Interior, Natural Blue, # Piece(s), 0.25 in., # ft., Cut

LIGHT TAPE STRIPS: LT-INT, NATURAL BLUE:050 INT, Natural Blue

Interior, Natural Blue, # Piece(s), 0.50 in., # ft., Cut


Interior, Natural Blue, # Piece(s), 1 in., # ft., Cut




ITEM DESCRIPTIONLIGHT TAPE STRIPS: LT-INT, NATURAL BLUE:200 INT, Natural Blue








MOUNTING SYSTEMS: 0.5 in. Transfer Tape 0.5 in. Adhesive Tape

MOUNTING SYSTEMS: 0.5 in. VHB 0.5 in. Mounting Tape

MOUNTING SYSTEMS: 1.0 in. Transfer Tape 1 in. Adhesive TapeMOUNTING SYSTEMS: 2.O in. Transfer Tape 2 in. Adhesive TapeMOUNTING SYSTEMS: 3.0 in. Transfer Tape 3 in. Adhesive TapeMOUNTING SYSTEMS: 4.0 in. Transfer Tape 4 in. Adhesive TapeMOUNTING SYSTEMS: Mount-Aqua 50 Flexible Extrusion with 0.5 in. Light Tape

MOUNTING SYSTEMS: Mount-Clip 25 0.25 in. Mounting Clips to secure 0.25 in. channel to structure




MOUNTING SYSTEMS: Mount-Ext 25 0.25 in. Light Tape Mounting ChannelMOUNTING SYSTEMS: Mount-Ext 50 0.5 in. Light Tape Mounting ChannelMOUNTING SYSTEMS: Mount-Ext 100 1.0 in. Light Tape Mounting ChannelMOUNTING SYSTEMS: Mount-Ext 200 2.0 in. Light Tape Mounting ChannelMOUNTING SYSTEMS: Mount-Mounting Tape Mounting TapeMOUNTING SYSTEMS: Mount-Velcro # feet

MOUNTING SYSTEMS: Mount-VibraMountX in. double sided black foam adhesive tape x in. thick - Ideal for shock and vibration absorption.

MOUNTING SYSTEMS: DuraShield 100

DuraShield is a clear, non-yellowing, removable urethane film overlay that leaves no residue when removed. It is designed to provide a protective, puncture resistant shield to reduce abra-sion while maintaining the low profile.

MOUNTING SYSTEMS: UltraBond 100

UltraBond is a white foamed acrylic core that is coated on both sides with high performance acrylic adhesives. It has excellent weathering properties, and has exceptional dynamic shear properties at hot and cold temperatures.

MOUNTING SYSTEMS: Mount-Vinyl Grey Vinyl Mounting Channel 0.25 in. or 0.50 in.POWER SUPPLIES: PS Adaptor AC Adaptor, 100/220

POWER SUPPLIES: PS-Adaptor Jack Jack-to-Jack for DC to AC Input



R

R

www.lighttape.com

ITEM DESCRIPTION

POWER SUPPLIES: PS-DC20Drive Light Tape lamps from 1 sq. in. to 20 sq. in with 12V DC input. Built in reverse polarity protection, no-load protec-tion and short circuit protection

POWER SUPPLIES: PS-DC20PDrive Light Tape lamps from 1 sq. in. to 20 sq. in. with 12V DC input. Built in reverse polarity protection, no-load protection, short circuit protection and mounting platform attached to unit

POWER SUPPLIES: PS-DC50Drive Light Tape lamps from 20 sq. in. to 50 sq. in. with 12V DC input. Built in reverse polarity protection, no-load protec-tion and short circuit protection

POWER SUPPLIES: PS-DC50PDrive Light Tape lamps from 20 sq. in. to 50 sq. in. with 12V DC input. Built in reverse polarity protection, no-load protection, short circuit protection and mounting platform attached to unit

POWER SUPPLIES: PS-DC50+Drive Light Tape lamps from 20 sq. in. to 50 sq. in. with 12V DC input. High efficiency inverters with built in reverse polarity protection, no-load protection and short circuit protection

POWER SUPPLIES: PS-DC100Drive Light Tape lamps from 50 sq. in. to 100 sq. in. with 12V DC input. Built in reverse polarity protection, no-load pro-tection and short circuit protection

POWER SUPPLIES: PS-DC100+Drive Light Tape lamps from 50 sq. in. to 100 sq. in. with 12V DC input. High efficiency inverters with built in reverse polarity protection, no-load protection and short circuit protection

POWER SUPPLIES: PS-DC150+Drive Light Tape lamps from 50 sq. in. to 150 sq. in. with 12V DC input. High efficiency inverters with built in reverse po-larity protection, no-load protection and short circuit protection

POWER SUPPLIES: PS-DC500+

Drive Light Tape lamps from 100 sq. in. to 500 sq. in. with 12V DC input. High efficiency inverters with built in reverse polarity protection, no-load protection, short circuit protection and mounting platform

POWER SUPPLIES: PS-DC9VDrive Light Tape lamps from 5 sq. in. to 33 sq. in. with 9V DC input. Designed with small case and clip for wearable applications

POWER SUPPLIES: PS-SD 400Power Supply, 120 or 240 Volt AC, Illuminates 100-400 square inches

POWER SUPPLIES: PS-SD 1000Power Supply, 120/240 Volt AC, Illuminates 450-1000 square inches

POWER SUPPLIES: PS-SD 1800Power Supply, 24 Volt DC, Illuminates 600-1800 square inches





Documents

Light Tape Design Guide