LG+32LN520B+Ch+LD36M+LED+TV

Printed in KoreaP/NO : MFL67729505 (1304-REV00)

CHASSIS : LD36M

MODEL : 32LN52** 32LN52**-ZA

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

LED TVSERVICE MANUAL

North/Latin America http://aic.lgservice.comEurope/Africa http://eic.lgservice.comAsia/Oceania http://biz.lgservice.com

Internal Use Only

- 2 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.Only for training and service purposes

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ........................................................................ 3

SERVICING PRECAUTIONS ................................................................... 4

SPECIFICATION ...................................................................................... 6

ADJUSTMENT INSTRUCTION ............................................................. 10

SCREW ASSEMBLY WORKING GUIDE ............................................... 16

DISASSEMBLY WORKING GUIDE ........................................................ 17

BLOCK DIAGRAM ................................................................................. 18

EXPLODED VIEW .................................................................................. 21

SCHEMATIC CIRCUIT DIAGRAM ..............................................................


Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View.It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

Always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 M and 5.2 M. When the exposed metal has no return path to the chassis the reading must be infinite.An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts.Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA.In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

IMPORTANT SAFETY NOTICE

SAFETY PRECAUTIONS


SERVICING PRECAUTIONSCAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication.NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precau-tions. Remember: Safety First.

General Servicing Precautions1. Always unplug the receiver AC power cord from the AC power

source before;a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.b. Disconnecting or reconnecting any receiver electrical plug

or other electrical connection.c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver.CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explo-sion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe.Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength)CAUTION: This is a flammable mixture.Unless specified otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead.Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this service manual.CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) DevicesSome semiconductor (solid-state) devices can be damaged eas-ily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component dam-age caused by static by static electricity.1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alter-natively, obtain and wear a commercially available discharg-ing wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or expo-sure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some sol-der removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads elec-trically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective mate-rial to the chassis or circuit assembly into which the device will be installed.CAUTION: Be sure no power is applied to the chassis or cir-cuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replace-ment ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity suf-ficient to damage an ES device.)

General Soldering Guidelines1. Use a grounded-tip, low-wattage soldering iron and appropri-

ate tip size and shape that will maintain tip temperature within the range or 500 F to 600 F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.4. Thoroughly clean the surfaces to be soldered. Use a mall wire-

bristle (0.5 inch, or 1.25 cm) brush with a metal handle.Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering techniquea. Allow the soldering iron tip to reach normal temperature.

(500 F to 600 F)b. Heat the component lead until the solder melts.c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.CAUTION: Work quickly to avoid overheating the circuit board printed foil.

6. Use the following soldering technique.a. Allow the soldering iron tip to reach a normal temperature

(500 F to 600 F)b. First, hold the soldering iron tip and solder the strand

against the component lead until the solder melts.c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the compo-nent lead and the foil.CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.


IC Remove/ReplacementSome chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the cir-cuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal1. Desolder and straighten each IC lead in one operation by

gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement1. Carefully insert the replacement IC in the circuit board.2. Carefully bend each IC lead against the circuit foil pad and

solder it.3. Clean the soldered areas with a small wire-bristle brush.

(It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete TransistorRemoval/Replacement1. Remove the defective transistor by clipping its leads as close

as possible to the component body.2. Bend into a "U" shape the end of each of three leads remain-

ing on the circuit board.3. Bend into a "U" shape the replacement transistor leads.4. Connect the replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor DeviceRemoval/Replacement1. Heat and remove all solder from around the transistor leads.2. Remove the heat sink mounting screw (if so equipped).3. Carefully remove the transistor from the heat sink of the circuit

board.4. Insert new transistor in the circuit board.5. Solder each transistor lead, and clip off excess lead.6. Replace heat sink.

Diode Removal/Replacement1. Remove defective diode by clipping its leads as close as pos-

sible to diode body.2. Bend the two remaining leads perpendicular y to the circuit

board.3. Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.4. Securely crimp each connection and solder it.5. Inspect (on the circuit board copper side) the solder joints of

the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional ResistorRemoval/Replacement1. Clip each fuse or resistor lead at top of the circuit board hollow

stake.2. Securely crimp the leads of replacement component around

notch at stake top.

3. Solder the connections.CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil RepairExcessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed when-ever this condition is encountered.

At IC ConnectionsTo repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connec-tions).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. Carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other ConnectionsUse the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife.Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly con-nected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side.Carefully crimp and solder the connections.CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.


SPECIFICATIONNOTE : Specifications and others are subject to change without notice for improvement.

1. Application rangeThis specification is applied to the LED TV used LD36M chassis.

2. Requirement for TestEach part is tested as below without special appointment.

(1) Temperature: 25 C 5 C(77 F 9 F), CST: 40 C 5 C(2) Relative Humidity: 65 % 10 %(3) Power Voltage

: Standard input voltage (AC 100-240 V~, 50/60 Hz)* Standard Voltage of each products is marked by models.

(4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.

(5) The receiver must be operated for about 5 minutes prior to the adjustment.

3. Test method(1) Performance: LGE TV test method followed (2) Demanded other specification

- Safety : CE, IEC specification- EMC : CE, IEC specification

Model Market Appliance

32LN520B-ZA32LN5203-ZA42LN5200-ZA42LN5204-ZA

EU (PAL/DVB Market)Safety : IEC/EN60065

EMI : EN55013EMS : EN55020


No. Item Specification Remarks1 Market EU(PAL Market-37Countries) DTV & Analog (Total 37 countries)

DTV (MPEG2/4, DVB-T) : 37 countriesUK/Italy/Germany/France/Spain/Sweden/Finland/Neth-erlands/ Belgium/Luxemburg/ Greece/Denmark/Czech/Austria /Hungary/Swiss/Croatia/Turkey/Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia/Bosnia/Serbia/Albania/Kazakhstan/Belarus

DTV (MPEG2/4, DVB-C) : 37 countriesUK/Italy/Germany/France/Spain/Sweden/Finland/Neth-erlands/Belgium/Luxemburg/ Greece/Denmark/Czech/Austria/Hungary/Swiss/Croatia/Turkey/Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia/Bosnia/Serbia/Albania/Kazakhstan/Belarus

2 Broadcasting system

Analogue TV1) PAL-BG2) PAL-DK3) PAL-I/I4) SECAM-BG5) SECAM-DK6) SECAM L/L

Analogue TV : (RF) VHF: E2 to E12, UHF : E21 to E69(CATV) S1 to S20, HYPER: S21 to S47

Digital TV1) DVB-T/C Digital TV : VHF, UHF

3 Receiving systemAnalog : Upper Heterodyne

Digital : COFDM , QAM

DVB-T- Guard Interval (Bitrate_Mbit/s)1/4, 1/8, 1/16, 1/32- Modulation : Code RateQPSK : 1/2, 2/3, 3/4, 5/6, 7/816-QAM : 1/2, 2/3, 3/4, 5/6, 7/864-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 DVB-C- Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM

4 Scart Jack (1EA) PAL, SECAM Scart 1 Jack is Full scart and support RF-OUT(analog).5 HDMI Input (2EA) HDMI1/2-DTV Support HDCP6 USB (1EA) EMF, DivX HD, For SVC (download) JPEG, MP3, DivX HD

12 DVB

DVB-TCI : UK, Finland, Denmark, Norway, Sweden, Russia,

Spain, Ireland, Luxemburg, Belgium, NetherlandCI+ : France(Canal+), Italy(DGTVi)

DVB-CCI : Switzerland, Austria, Slovenia, Hungary, BulgariaCI+ : Switzerland(UPC,Cablecom), Netherland(Ziggo),

Germany(KDG,CWB), Finland(labwise)

4. Model General Specification


5. External Input Support format5.1. HDMI Input 1 (PC/DTV)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed RemarkPC(DVI) DDC

1 640*350 31.468 70.09 25.17 EGA X2 720*400 31.469 70.08 28.32 DOS O3 640*480 31.469 59.94 25.17 VESA(VGA) O4 800*600 37.879 60.31 40.00 VESA(SVGA) O5 1024*768 48.363 60.00 65.00 VESA(XGA) O6 1152*864 54.348 60.053 80.00 VESA O7 1360*768 47.712 60.015 85.50 VESA (WXGA) O8 1280*1024 63.981 60.020 108.0 VESA (SXGA) O FHD only9 1920*1080 67.50 60.00 148.5 HDTV 1080P O FHD only

DTV

1 720*480 31.47 59.94 27.00 SDTV 480P

2 720*480 31.50 60.00 27.027 SDTV 480P3 720*576 31.250 50.00 27.00 SDTV 576P4 1280*720 37.50 50.00 74.25 HDTV 720P5 1280*720 45.00 60.00 74.25 HDTV 720P6 1280*720 44.96 59.94 74.176 HDTV 720P7 1920*1080 28.125 50.00 74.25 HDTV 1080I8 1920*1080 33.75 60.00 74.25 HDTV 1080I9 1920*1080 33.72 59.94 74.176 HDTV 1080I

10 1920*1080 56.250 50.00 148.50 HDTV 1080P11 1920*1080 67.50 60.00 148.50 HDTV 1080P12 1920*1080 67.432 59.94 148.352 HDTV 1080P13 1920*1080 27.00 24.00 74.25 HDTV 1080P14 1920*1080 26.97 23.976 74.176 HDTV 1080P15 1920*1080 33.75 30.00 74.25 HDTV 1080P

5.2. USB InputNo. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1. 1920*1080 33.75 30.000 74.25 HDTV 1080P


Category Item Specification Remark

Photo JPG, PNG, BMP, TIF, TIFF, GIF 4096X4096Slide Show support.Background music support

Music

MP3 32kbps ~ 320kbps(Bit rate)32kHz ~ 48kHz(Sample rate)

WMA 128bps ~ 320kbps(Bit rate)8kHz ~ 48kHz(Sample rate)

WAV 1.44kbps(Bit rate)44.1kHz(Sample rate)

Category Codec Media Container Profile/Level Support Remark

Movie

Video

MPEG1/MPEG2

DAT, MPG, MPEG, DVD, TS, TRP, TP 1920X1080 @ 30I

MPEG4(Divx 3.11, Divx 4.12, Divx 5.x, Divx 6, Divx HD, Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1/2 )

AVI, DIVX, MP4, MKV, TS, TRP 1920X1080 @ 30P

H.264 AVI, MP4, MKV, TS, TRP, TP 1920X1080 @ 30P

Audio

MP3, MP3 Pro MP3 32kbps ~ 320kbps(Bit rate)32kHz ~ 48kHz(Sample rate)

AC3 AC3 32kbps ~ 640kbps(Bit rate)32kHz, 44.1kHz, 48kHz(Sample rate)

MPEG MPA 32kbps ~ 448kbps(Bit rate)32kHz ~ 48kHz(Sample rate)

AAC, HEAAC M4A 24kbps ~ 3844kbps(Bit rate)8kHz ~ 96kHz(Sample rate)

CDDA CDA 1.44kbps(Bit rate)44.1kHz(Sample rate)

LPCM AIF, AIFF, WAV

1.41Mbps ~ 9.6Mbps(Bit rate)Multi-channel 44.1kHz, 88.2kHz (Sample rate)48kHz, 96kHz (Sample rate) Stereo 176.4kHz, 192kHz(Sample rate)

ETC

Trick play

a. Pause & Resumeb. Fast forward (2x, 4x, 8x, 16x, 32x)c. Fast backward (2x, 4x, 8x, 16x,

32x)d. Forward slow motion (1/2x, 1/4x,

1/8x, 1/16x, 1/32x)

Variable video size(Full/Original) Can support video zoom in/out proc-ess when the video is display.

Video Preview(Movie Preview function is possible or not. like fast play or thumbnail when user move the cursor in the list)

Can support movie preview. But in preview mode, we don't support any trick mode process.

5.3. USB Input format


ADJUSTMENT INSTRUCTION1. Application Range

This specification sheet is applied to all of the LED TV with LD36M chassis.

2. Designation(1) The adjustment is according to the order which is designated

and which must be followed, according to the plan which can be changed only on agreeing.

(2) Power adjustment : Free Voltage.(3) Magnetic Field Condition: Nil.(4) Input signal Unit: Product Specification Standard.(5) Reserve after operation : Above 5 Minutes (Heat Run) Temperature : at 25 C 5 C Relative humidity : 65 10 % Input voltage : 220 V, 60 Hz(6) Adjustment equipments: Color Analyzer(CA-210 or CA-110),

DDC Adjustment Jig, Service remote control.(7) Push the "IN STOP" key - For memory initialization.

3. Main PCB check process APC - After Manual-Insert, executing APC

* Boot file Download(1) Execute ISP program "Mstar ISP Utility" and then click

"Config" tab.(2) Set as below, and then click "Auto Detect" and check "OK"

message.If "Error" is displayed, check connection between computer, jig, and set.

(3) Click "Read" tab, and then load download file(XXXX.bin) by clicking "Read".

(4) Click "Connect" tab. If "Can't" is displayed, check connection between computer, jig, and set.

(5) Click "Auto" tab and set as below.(6) Click "Run".(7) After downloading, check "OK" message.

* USB DOWNLOAD(1) Put the USB Stick to the USB socket.(2) Automatically detecting update file in USB Stick.

- If your downloaded program version in USB Stick is Low, it didn't work. But your downloaded version is High, USB data is automatically detecting.

(3) Show the message "Copying files from memory".(4) Updating is starting.

(5) Updating Completed, The TV will restart automatically in 5 seconds.

(6) If your TV is turned on, check your updated version and Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have, TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didnt have a DTV/ATV test on production line.

(1)

filexxx.bin

(4)

(5)

(6)

(7)...........OK

filexxx.bin

(2)

(3)

Please Check the Speed :To use speed betweenfrom 200KHz to 400KHz

Case1 : Software version up1. After downloading S/W by USB , TV set will reboot

automatically.2. Push In-stop key.3. Push Power on key.4. Function inspection5. After function inspection, Push In-stop key.

Case2 : Function check at the assembly line1. When TV set is entering on the assembly line, Push

In-stop key at first.2. Push Power on key for turning it on.

If you push Power on key, TV set will recover channel information by itself.

3. After function inspection, Push In-stop key.


* After downloading, have to adjust Tool Option again.(1) Push "IN-START" key in service remote control.(2) Select "Tool Option 1" and push "OK" key.(3) Punch in the number. (Each model has their number)(4) Completed selecting Tool option.

3.1. ADC Process* If ADC processes as OTP, There is no need to proceed

internal ADC.- Enter Service Mode by pushing "ADJ" key,- Enter Internal ADC mode by pushing "" key at "7. ADC

Calibration".

Using "P-ONLY" key of the Adjustment remote control, power on TV.

* ADC Calibration Protocol (RS232)

Adjust Sequence aa 00 00 [Enter Adjust Mode] xb 00 40 [Component Input480i)] ad 00 10 [Adjust 480i & 1080p Comp] aa 00 90 End Adjust mode* Required equipment : Adjustment remote control.

3.2. EDID Download After enter Service Mode by pushing "ADJ" key. Enter EDID D/L menu. Enter "START" by pushing "OK" key.

Never connect HDMI cable when EDID downloaded.

3.3. EDID data(1) HD HDMI EDID data(2D Model)

(2) FHD HDMI EDID data(2D Model)

(3) Detail EDID Options are belowa. Product ID

b. Serial No: Controlled on production line.c. Month, Year: Controlled on production line:

ex) Week : '01' -> '01'Year : '2013' -> '17' fix

d. Model Name(Hex):cf) TV sets model name in EDID data is below.

e. Checksum: Changeable by total EDID data.

f. Vendor Specific(HDMI)

NO Item CMD 1 CMD 2 Data 0

EnterAdjust MODE

Adjust Mode In A A 0 0

When transfer the Mode In, Carry the command.

ADC adjust ADC Adjust A D 1 0 Automatically adjustment(The use of a internal pattern)

0 1 2 3 4 5 6 7 8 9 A B C D E F00 00 FF FF FF FF FF FF 00 1E 6D a b10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 2620 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 8030 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 3050 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d70 d 01 e80 02 03 22 F1 4E 10 9F 04 13 05 14 03 02 12 20 2190 22 15 01 26 15 07 50 09 57 07 fA0 f 01 1D 80 18 71 1C 16 20 58 2C 25 00 20 C2B0 31 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00C0 20 C2 31 00 00 1E 02 3A 80 18 71 38 2D 40 58 2CD0 45 00 A0 5A 00 00 00 1E 01 1D 00 BC 52 D0 1E 20E0 B8 28 55 40 C4 8E 21 00 00 1E 00 00 00 00 00 00F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e

MODEL NAME HEX EDID Table DDC Function

HD/FHD Model 0001 01 00 Analog/Digital

Model name MODEL NAME(HEX)

LG TV 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV)

EDID C/S dataHD

HDMI

Check sum(Hex)

Block 0 A3

Block 15B (HDMI1)4B (HDMI2)

Input Model name(HEX)

HDMI1 67030C001000801E

HDMI2 67030C002000801E

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5

5. Tool Option Commercial

6. Country Group

7. Area Option

8.ADC Calibration

9. White Balance

10. 10 Point WB

11. Test Pattern

12 EDID D/L

13. Sub B/C

14. Ext. Input Adjust

ADC Calibration

ADC Comp 480i

ADC Comp 1080p

ADC Type

OK

OK

OTP

Start Reset

EZ ADJUST0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5


6. Country Group

7. Area Option

8. ADC Calibration

9. White Balance

10. 10 Point WB

11. Test Pattern

12. EDID D/L

13. Sub B/C


EDID D/L HDMI1 NG

HDMI2 NG

Start Reset

0 1 2 3 4 5 6 7 8 9 A B C D E F00 00 FF FF FF FF FF FF 00 1E 6D a b10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 2620 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 0130 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 7040 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 3050 18 88 03 06 40 84 63 00 00 18 00 00 00 FD 00 3A60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d70 d 01 e80 02 03 22 F1 4E 10 1F 04 93 05 14 03 02 12 20 2190 22 15 01 26 15 07 50 09 57 07 fA0 80 1E 01 1D 80 18 71 1C 16 20 58 2C 25 00 A0 5AB0 00 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00C0 20 C2 31 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3ED0 96 00 A0 5A 00 00 00 18 02 3A 80 18 71 38 2D 40E0 58 2C 45 00 A0 5A 00 00 00 1E 00 00 00 00 00 00F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e


3.4. Function Check- Check display and sound

Check Input and Signal items.1) TV2) AV (SCART / CVBS)3) HDMI* Display and Sound check is executed by Remote control.

Not to push the INSTOP key after completion if the function inspection.

4. Total Assembly line process4.1.V-com adjustment

Insert V-com adjust pattern(1) Push Power Only key on SVC remote controller.(2) Push Yellow key.(4) Push number 0 key.

- Default : 160

V-com adjust (Variable range : 5)- 5 digit move push navigation key up or down.- 1 digit move push navigation key left or right.Keep move V-com adjust until disappear flicker.After V-com adjust push enter (save) key.

Exit V-COM adjust pattern- Push Power Only key on SVC remote control.

4.2. White Balance adjustment W/B Equipment condition

CA210 : LED -> CH14, Test signal: Inner pattern(80IRE) Above 5 minutes H/run in the inner pattern. (power on key

of adjust remote control)

Normal line(LGD/CMI, March ~ December for Gumi, Global)

Normal line(LGD/CMI, January ~ February for Gumi, Apply not Cinema Screen)

* Aging chamber(LGD/CMI)

* Connecting picture of the measuring instrument(On Automatic control)Inside PATTERN is used when W/B is controlled. Connect to auto controller or push Adjustment R/C P-ONLY Enter the mode of White-Balance, the pattern will come out.Mode Temp Coordinate spec

Cool 13,000 K X=0.271 (0.002)Y=0.270 (0.002)

Medium 9,300 K X=0.285 (0.002)Y=0.293 (0.002)

Warm 6,500 K X=0.313 (0.002)Y=0.329 (0.002)

NetCase4 Aging time(Min)

Cool Medium WarmX y x y x y

271 270 285 293 313 3291 0-2 281 287 295 310 320 3422 3-5 280 285 294 308 319 3403 6-9 278 284 292 307 317 3394 10-19 276 281 290 304 315 3365 20-35 275 277 289 300 314 3326 36-49 274 274 288 297 313 3297 50-79 273 272 287 295 312 3278 80-119 272 271 286 294 311 3269 Over 120 271 270 285 293 310 325



271 270 285 293 313 3291 0-2 283 292 297 315 322 3472 3-5 282 290 296 313 321 3453 6-9 280 288 294 311 319 3434 10-19 277 284 291 307 316 3395 20-35 275 279 289 302 314 3346 36-49 274 275 288 298 313 3307 50-79 273 272 287 295 312 327 8 80-119 272 271 286 294 311 3269 Over 120 271 270 285 293 310 325



271 270 285 293 313 3291 0-2 280 285 294 308 319 3402 3-5 276 280 290 303 315 335 3 6-9 272 275 286 298 311 330 4 10-19 269 272 283 295 308 327 5 20-35 267 268 281 291 306 323 6 36-49 266 265 280 288 305 320 7 50-79 265 263 279 286 304 318 8 80-119 264 261 278 284 303 316 9 Over 120 264 260 278 283 303 315

Full White Pattern CA-210

COLORANALYZERTYPE : CA-210

RS-232C Communication

V-Com V-COM

Press OK to Saver

160


* Auto-control interface and directions(1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).(2) Adhere closely the Color analyzer(CA210) to the module

less than 10 cm distance, keep it with the surface of the Module and Color analyzer's prove vertically.(80 ~ 100).

(3) Aging time- After aging start, keep the power on (no suspension of power supply) and heat-run over 5 minutes.

- Using 'no signal' or 'POWER ONLY' or the others, check the back light on.

Auto adjustment Map(using RS-232C to USB cable)RS-232C COMMAND[CMD ID DATA] Wb 00 00 White Balance Start Wb 00 ff White Balance End

Color Temperature : COOL, Medium, Warm. One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0.(When R/G/B Gain are all C0, it is the FULL Dynamic Range of Module)

* Manual W/B process using adjust Remote control. After enter Service Mode by pushing "ADJ" key, Enter White Balance by pushing "" key at "9. White

Balance".

* CASE Cool ModeFirst adjust the coordinate far away from the target value(x, y).B.1) x, y > target2) x, y < target3) x >target, y < target4) x < target, y > target - Every 4 case have to fit y value by adjusting B Gain

and then fit x value by adjusting R-Gain. - In this case, increasing/decreasing of B Gain and R

Gain can be adjusted.

How to adjust1) In case G gain more than 172 Adjust R Gain and B Gain less than 192 2) if the G gain value be adjusted down to 172 One of the R/B Gain is 2543) if G Gain is 172, More than one of R/B Gain is to be

between 192~254.

* CASE Medium / WarmFirst adjust the coordinate far away from the target value(x, y).1) x, y > target

i) Decrease the R, G. 2) x, y < target

i) First decrease the B gain, ii) Decrease the one of the others.

3) x > target, y < targeti) First decrease B, so make y a little more than the target.ii) Adjust x value by decreasing the R

4) x < target, y > targeti) First decrease B, so make x a little more than the target.ii) Adjust x value by decreasing the G

* After you finished all adjustments, Press "In-start" key and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable.For correct it to the model's module from factory Jig model.

* Push the "IN STOP" key after completing the function inspection. And Mechanical Power Switch must be set ON.

4.3. Outgoing condition Configuration When pressing IN-STOP key by SVC remocon, Red LED

are blinked alternatively. And then automatically turn off.(Must not AC power OFF during blinking)

RS-232C COMMAND[CMD ID DATA] MIN

CENTER(DEFAULT) MAX

Cool Mid Warm Cool Mid Warm

R Gain jg Ja jd 00 172 192 192 254

G Gain jh Jb je 00 172 192 192 192

B Gain ji Jc jf 00 192 192 172 254

R Cut 64 64 64 128

G Cut 64 64 64 128

B Cut 64 64 64 128

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5


6. Country Group

7. Area Option

8. ADC Calibration

9. White Balance

10. 10 Point WB

11. Test Pattern

12 EDID D/L

13. Sub B/C


Whit Balance

Color Temp.

R-Gain

G-Gain

B-Gain

R-Cut

G-Cut

B-Cut

Test-Pattern

Backlight

Reset To Set

Cool

172

172

192

64

64

64

ON

100


5. HI-POT Test5.1. HI-POT auto-check preparation

- Check the POWER cable and SIGNAL cable insertion condition

5.2. HI-POT auto-check(1) Pallet moves in the station. (POWER CORD / AV CORD is

tightly inserted)(2) Connect the AV JACK Tester.(3) Controller (GWS103-4) on.(4) HI-POT test (Auto)

- If Test is failed, Buzzer operates.- If Test is passed, GOOD Lamp on and move to next proc-

ess automatically.

5.3. Checkpoint(1) Test voltage

- Touchable Metal : 3 KV / min at 100 mA- SIGNAL : 3 KV / min at 100 mA

(2) TEST time: 1 second. (case : mass production )(3) TEST POINT

- Touchable Metal => LIVE & NEUTRAL : Touchable Metal.- SIGNAL => LIVE & NEUTRAL : SIGNAL.

6. Model name & Serial number D/L Press "Power on" key of service remote control.

(Baud rate : 115200 bps) Connect RS232 Signal Cable to RS-232 Jack. Write Serial number Must check the serial number at the Diagnostics of SET UP menu. (Refer to below).

6.1. Signal Table

CMD : A0hLENGTH : 85~94h (1~16 bytes)ADH : EEPROM Sub Address high (00~1F)ADL : EEPROM Sub Address low (00~FF)Data : Write dataCS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_nDelay : 20ms

6.2. Command Set

* DescriptionFOS Default write : writeVtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0, PhaseData write : Model Name and Serial Number write in EEPROM,.

6.3. Method & notice(1) Serial number D/L is using of scan equipment.(2) Setting of scan equipment operated by Manufacturing

Technology Group.(3) Serial number D/L must be conformed when it is produced in

production line, because serial number D/L is mandatory by D-book 4.0.

* Manual Download(Model Name and Serial Number)If the TV set is downloaded by OTA or Service man, sometimes model name or serial number is initialized.(Not always)There is impossible to download by bar code scan, so It need Manual download.1) Press the "Instart" key of Adjustment remote control.2) Go to the menu "6.Model Number D/L" like below photo.3) Input the Factory model name(ex 32LN520B-ZA) or Serial

number like photo.

4) Check the model name Instart menu Factory name displayed (ex 32LN520B-ZA)

5) Check the Diagnostics (DTV country only) Buyer model displayed (ex 32LN520B-ZA)

CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY

Adjust mode CMD(hex) LENGTH(hex) Description

EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)


7. MAC Address & CI+ key download7.1 MAC Address 7.1.1 Equipment & Condition

Play file : Serial.exe MAC Address edit Input Start / End MAC address

7.1.2 Download method(1) Communication Prot connection

Connection : PCBA (USB Port) USB to Serial Adapter (UC-232A) RS-232C cable PC(RS-232C port) * Caution : LJ21* chassis support only UC-232A driver. (only

use this one. )

(2) MAC Address(Not use) & CI+ Key Download Set CI+ Key path Directory at Start Mac & CI+ Download

Programme Com 1,2,3,4 and 115200(Baudrate)

Port connection button click(1) Push the (2) MAC Address write. At success Download, check the OK (3) Start CI+ Key Download, Push the (4) Check the OK or NG

GP4_LOW


Screw specification and application situation

Check Screw Type When Screw is assembled at 'A' Part. If 'B' Screw is used at the 'A' part, Module will get damaged.

SCREW ASSEMBLY WORKING GUIDE

FAB31339403

(M3*L6, BK, Machine)

4EA

FAB31639801(M4*L10, BK, Taptite) 9EA

FAB30016124 (M4*L14, BK, Machine) 2EA

C C

A A

B B

B

A

A A

A A

B

A A


DISASSEMBLY WORKING GUIDE

Disassemble 2 screws that bind Stand Assy and set

Disassemble 7 screws around the 4 edges of set after Separation Stand Assy

1 2

Disassemble 4 screws that fix Side AV bracket and Back-cover.

3

After opening cover of IR Assy Disconnect IR cable

4

5 6

After lifting up back-cover slightly, Disconnect SPK cable

Remove the back-cover and Disconnect LVDS and Power cable from Main PCB


NAND flash

1Gbit

Buffer

IC1902

CI_ADDR[0:14]

MAIN IC

MSTA

RMSD804K

KX

IC101

IF_P

/ N

PCMCIA (SIDE)

FE_T

S_D

ATA

[0:7]/C

LK/VAL/SYNC

CI_TS

_DATA

[0:7]/C

LK/VAL/SYNC

HDMI2

PCM_A

[0:7]

Aud

io AMP

(STA

380B

WF)

IC3401

I2SUSB_D

M/DP

DDR3 2G

bit

H5T

Q2G

63DFR

-PBC

(HYNIX)

IC1201

EEPROM, 256Kbit

(RENESAS)

IC104

SC1_RGB

DTV

/MNT_

VOUT

Aud

io L/R IN

Aud

io_L

/R OUT

Full Scart

DDR_D

ata[0:15

], DQS, D

M

USB (S

IDE)

SCL/SDASCL/SDA, D

ata

SCL/SDA

Video

AMP

IC2802

TV Tuner

DVB-T/C

TDSS-G501D

HDMI1

(10)

SCL/SDA, D

ata

(10)

SCL/SDA

Serial F

lash

, 8Mbit

(MACRONIX)

IC1300

SPI S

CK/SDI

SC1_CVBS_IN

(11)

(15) (8)

(11)

CI_DATA

[0:7]

(8)

CI_ADDR[8:14]

(7)

CI_ADDR[0:7]

(8)

LCD Pan

el (F

HD 51P

/HD 30P

)

LVDS (8 bit)

Bac

k Ligh

t

LED Driv

er

Spe

aker

BLOCK DIAGRAM1. MAIN


24V_

Adap

ter

24V LED Driver

IC404

DCDC,IC

12V

Q405

Aud

io AMP

24V

IC401

DCDC,IC

5VUSB, C

I, Normal

Q409

12V

PANEL

Scart AMP

IC400

DCDC,IC

3.5V

Q403

3.3V

TU, E

EPROM

NAND, M

AIN IC

IC402

LDO

2.5V

IC2603

LDO

1.8V

MAIN IC

TU

IC403

DCDC,IC

IC407

LDO

1.1V

MIAN IC

Core

1.5V

DDR

NVRAM, M

AIN IC

2. POWER


I2C_S

CKM2

I2C_S

CAM

2NVRAM

IC104

22

+3.3V_N

ORMAL

I2S_

IN_B

CK

I2S_

IN_S

D

S7LR

MMSD

804K

KX

Audio AM

PIC3400

I2C_S

CKM1

I2C_S

DAM

1

1K

33

+3.3V_TU

20pF

TU_A

DEM

OD

2.2K

1K

+3.3V_N

ORMAL

22

20pF

AMP_

SDA/SC

L

I2C_S

DA/SC

L

TU_S

DA/SC

L

SPI1_C

KSP

I1_D

IT-CON

NVRAM

0

+3.3V_N

ORMAL

1K

0

V-COM_S

DA/SC

L

3. I2C


Set + Stand

Stand

Bas

e+

Stand

Bod

y

A2

A9

A31

A10

900

200

400

540

521

910

120

590

591

LV1

EXPLODED VIEW

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. IR/CONTROL

2012/07/18

6

NC4_S7LRM

C6070.1uF16V

OPT

R601100

+3.5V_ST

L600BLM18PG121SN1D

KEY2

R60210K1%

IR

R600100

C604100pF50V

+3.5V_ST C6031000pF50V

R60310K1%

C6020.1uF

16V

KEY1

+3.5V_ST

R6073.3K

LED_R/BUZZ

P60012507WR-08L

1

2

3

4

5

6

7

8

9

R6101.8K

L601BLM18PG121SN1D

CONTROL_FILTER

L602BLM18PG121SN1D

CONTROL_FILTER C6080.1uF16V

CONTROL_FILTER

C6090.1uF16V

CONTROL_FILTER

R6110

CONTROL_NO_FILTER

R6120

CONTROL_NO_FILTER

IR/LED and Control

Copyright 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

LGE Internal Use Only

USB DOWN STREAM

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

13/03/27

USB 7

NC4_S7LRM

JK700

3

A

U

0

4

S

-

3

0

5

-

Z

C

-

(

L

G

)

1

2

3

4

5

D700RCLAMP0502BA

OPT

SIDE_USB1_DM

SIDE_USB1_DP

+5V_USB

C70022uF10V

ZD7005V

OPT

USB (SIDE)



THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. S_FLASH_OS

2012/06/20

13

NC4_S7LRM

SPI_SCK

+3.5V_ST+3.5V_ST

C13000.1uF

R13014.7K

OPT

/SPI_CS

SPI_SDO

IC1300MX25L8006EM2I-12G

SPI_FLASH_MACRONIX

3WP#

2SO/SIO1

4GND

1CS#

5SI/SIO0

6SCLK

7HOLD#

8VCC

R130233

R130010K

OPT

SPI_SDI

/FLASH_WP

IC1300-*1W25Q80BVSSIG

SPI_FLASH_WINBOND

3%WP[IO2]

2DO[IO1]

4GND

1CS

5DI[IO0]

6CLK

7HOLD[IO3]

8VCC

+3.5V_ST

Serial Flash for SPI boot(OS)



THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PCMCI

2013/03/25

19

NC4_S7LRM

FE_TS_DATA[7]

CI_ADDR[4]CI_ADDR[3]

CI_ADDR[5]

FE_TS_DATA[3]

CI_ADDR[7]

CI_DATA[4]

FE_TS_DATA[0]

CI_ADDR[0]

C

I

_

D

A

T

A

[

0

-

7

]

C

I

_

D

A

T

A

[

0

-

7

]

CI_DATA[4]

CI_DATA[6]

CI_DATA[0]

CI_DATA[0]

CI_ADDR[2]

CI_DATA[7]

CI_DATA[5]

PCM_D[2]

FE_TS_DATA[6]

CI_DATA[5]

CI_DATA[3]

PCM_D[0]

PCM_D[4]

CI_DATA[7]

C

I

_

D

A

T

A

[

0

-

7

]

CI_DATA[1]

PCM_D[7]

CI_ADDR[13]

PCM_D[1]

CI_ADDR[10]

P

C

M

_

D

[

0

-

7

]

CI_ADDR[6]

CI_DATA[2]

FE_TS_DATA[5]

CI_ADDR[12]

CI_ADDR[14]

CI_ADDR[9]

PCM_D[6]

CI_ADDR[11]

CI_DATA[2]

CI_ADDR[8]

CI_DATA[3]

FE_TS_DATA[2]FE_TS_DATA[1]

PCM_D[3]

PCM_D[5]

CI_ADDR[1]

FE_TS_DATA[4]

F

E

_

T

S

_

D

A

T

A

[

0

-

7

]

CI_DATA[6]

CI_DATA[1]

R1925 100

CI_MIVAL_ERR

CI_MDI[5]

PCM_A[3]

R1919 47

CI_IOWR

GND

AR1912 33

R1908100

/PCM_IORD

CI_DET

CI_OE

CI_ADDR[13]

/CI_CD2

CI_TS_DATA[7]

CI_ADDR[9]

PCM_A[6]

CI_MDI[0]

PCM_A[8]

CI_DATA[0-7]

CI_MDI[4]

CI_ADDR[14]

+5V_CI_ON

R1902 47

CI_MDI[3]

/PCM_CE

CI_TS_DATA[2]

CI_TS_DATA[6]

CI_MDI[1]

PCM_A[2]

PCM_A[0]

PCM_A[13]

CI_DET

R1927 33

CI_ADDR[11]L1902

BLM18PG121SN1D

AR1907 33

CI_MDI[6]

CI_ADDR[8]

+5V_Normal

CI_TS_DATA[5]

FE_TS_VAL_ERR

FE_TS_CLK

GND

CI_MDI[7]

FE_TS_SYNC

R1905 10K

R1901 47

/PCM_IOWR

/PCM_WE/PCM_OE

GND

PCM_A[5]

C19090.1uF

CI_IOWR

CI_MDI[6]

CI_DATA[0-7]

CI_WE

GND

CI_TS_DATA[1]

/CI_CD2

CI_TS_DATA[3]

CI_MDI[7]

AR1913 33

CI_IORD

C19142pF50V R190410K

PCM_A[11]

C19130.1uF16V

PCM_A[14]

/PCM_IRQA

CI_MDI[2]

CI_OE

CI_MIVAL_ERR

CI_MDI[0]

REG

CI_ADDR[0-14]

/CI_CD1

CI_MDI[2]

PCM_A[1]

REG

CI_TS_SYNC

+5V_Normal

PCM_A[4]

R1926 33

C190610uF10V

PCM_A[12]CI_ADDR[12]

CI_MISTRT

AR1905 33

CI_MCLKI

PCM_A[9]

IC190174LVC1G32GW

OR_GARE_CI_PHILIPS

3GND

2A

4 Y

1B 5 VCC

CI_TS_CLK

C19050.1uFGND

CI_ADDR[10]

AR1909 33

AR1906 33

CI_IORD

CI_TS_DATA[4]

CI_MDI[5]

CI_MDI[3]

AR190133

R1906 10K

R191710K

/PCM_REG

R192110K

PCM_RST

AR1903 33

R190310K

CI_MCLKI

FE_TS_DATA[0-7]

PCM_D[0-7]

R1907100

PCM_A[7]

CI_MDI[1]

PCM_A[10]

CI_TS_VAL

CI_MDI[4]

R1920 100

/CI_CD1

CI_WE

AR1908 33

CI_TS_DATA[0]

IC1902

T

C

7

4

L

C

X

2

4

4

F

T

0ITO742440D

TOSHIBA

32Y4

21A1

41A2

11OE

61A3

52Y3

72Y2

81A4

92Y1

10GND

112A1

121Y4

132A2

141Y3

152A3

161Y2

172A4

181Y1

192OE

20VCC

/PCM_WAIT

CI_MISTRT

+3.3V_Normal

+3.3V_Normal

R190910K

+5V_Normal

C19010.1uF

+5V_Normal

R191010K

GND +3.3V_Normal

R191147

/PCM_CD

P190110067972-000LF

CI_SLOT_JACK

G1G2

57

21

52

16

10

47

41

5

36

59

23

45

54

18

49

43

13

7

38

2

25

56

20

51

15

9

46

40

4

35

58

22

53

17

11

48

42

12

6

37

1

24

55

19

50

44

14

8

39

3

2660276128622963306431323334

65666768

69

R1928 33R1929 33R1930 100

C19101uF25V

PCM_5V_CTL

R1914100

R1922100K

R191310K

+5V_CI_ON+5V_Normal IC1903

AP2151WG-7

3FLG

2GND

4EN

1OUT

5IN


CI_ADDR[0]

CI_ADDR[3]

CI_ADDR[6]


CI_ADDR[7]

IC1901-*1SN74LVC1G32DCKR

OR_GARE_CI_TI

3GND

2B

4Y

1A

5VCC

AR1915100

AR1914100

CI TS INPUT

CI POWER ENABLE CONTROL

CLOSE TO MSTAR

CI SLOT

CI DETECT

CI HOST I/F

* Option name of this page : CI_SLOTCI Region(because of Hong Kong)

CLOSE TO MSTAR

CLOSE TO MSTAR



THERMAL


2013/02/05

AMP_STA380BWEF 34

NC4_S7LRM

SPK_L+

+3.5V_ST

AMP_MUTEAMP_SCL

C34200.22uF50V

R340310K

SPK_R-

C34151uF50V

+3.3V_Normal

R341043

R340843

R340210K

C34121uF50V

C34241000pF50V

R340110K

SPK_L+

P3401WAFER-ANGLE

1

2

3

4

C34251000pF50V

C34080.1uF16V

C34271000pF50V

C34190.22uF50V

SPK_L-

SPK_L-

+3.3V_Normal

AUD_MASTER_CLK

C34230.22uF50V

C34261000pF50V

C34110.1uF50V

C34160.1uF50V

C3413330pF50V

C34220.22uF50V

SPK_R+

Q3401MMBT3904(NXP)

E

B

C

AUD_LRCH

C3414330pF50V

R340943

AUD_SCK

AMP_RESET

SPK_R+

R341143

C34070.1uF16V

POWER_DET

+24V

C34210.22uF50V

C34011000pF50V

C34090.1uF16V

AMP_SDA

C34180.22uF50V

R34050

OPT

SPK_R-

C34042.2uF

10V

C34030.1uF

16V

AUD_LRCK

R3406 0

R3407 0

IC3401STA380BWF

1 VCC_REG2 VSS_REG3 OUT2B4 GND25 VCC26 OUT2A7 OUT1B8 VCC19 GND1

10 OUT1A11 VDD_REG12 GND_REG

1

3

N

C

_

1

1

4

N

C

_

2

1

5

N

C

_

3

1

6

N

C

_

4

1

7

N

C

_

5

1

8

N

C

_

6

1

9

N

C

_

7

2

0

N

C

_

8

2

1

N

C

_

9

2

2

N

C

_

1

0

2

3

N

C

_

1

1

2

4

N

C

_

1

2

25NC_1326NC_1427NC_1528VDDDIG129GNDDIG130FFX3A31FFX3B32EAPD/FFX4A33TWARNEXT/FFX4B34VREGFILT35AGNDPLL36MCLK

3

7

B

I

C

K

I

3

8

L

R

C

K

I

3

9

S

D

I

4

0

R

E

S

E

T

4

1

P

W

D

N

4

2

I

N

T

L

I

N

E

4

3

S

D

A

4

4

S

C

L

4

5

S

A

4

6

T

E

S

T

M

O

D

E

4

7

G

N

D

D

I

G

2

4

8

V

D

D

D

I

G

2

49

[

E

P

]

L340410uH

COIL_ABCO

L340210uH

COIL_ABCO

L340510uH

COIL_ABCO

L340310uH

COIL_ABCO

C341710uF35V3216

R3404100

L3401UBW2012-121F

L3402-*110.0uH

COIL_GETPLUSL3403-*110.0uH



COIL_GETPLUS

AUDIO AMP(STA380BWEF)

SPEAKER_R

SPEAKER_L




2012/06/20

MSTAR DEBUG_4PIN 39

NC4_S7LRM

RGB_DDC_SCL

RGB_DDC_SDA

P390012505WS-04A00

MSTAR_DEBUG_4P

1

2

3

4

5

J

P

_

G

N

D

2

J

P

_

G

N

D

3

J

P

_

G

N

D

4

J

P

_

G

N

D

1

MSTART DEBUG_4PIN



THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. RS232C_4P_OS

2012/06/20

40

NC4_S7LRM

PM_RXD

+3.5V_ST

R4001100

R4000100

P400012507WS-04L

RS232C_DEBUG_4P

1VCC

2PM_RXD

3GND

4RM_TXD

5

GND

PM_TXD

RS-232C




2012/07/04

EU_TP(ERRC) 41

NC4_S7LRM

HP_DET

BR_RESET_DEMODRF_SWITCH_CTL

HP_LOUT

HP_ROUT

SIDE_HP_MUTE

EPHY_TN

EPHY_RN

EPHY_TP

EPHY_RP

LNA_CTRL_1LNA_CTRL_2

IF_AGC_SEL

DEMOD_SDA

DEMOD_SCL

S2_RESET

LNA2_CTL

EU NOT USED TP (ERRC)



THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. M1_DDR (1DDR)

2012/06/21

54

NC4_S7LRM

A-MDMU

A-MWEB

A-MA7

A-MDQL5

A-MBA2

A-MCASB

A-MA8

A-MDQSU

A-MA12

A-MDQL7

A-MA14

A-MDQL2

R

1

2

3

6

5

6

1

%

A-MDQL0

A-MODT

A-MCASB

A-MA2

A-MDQU7

A-MA1

A-MDQL0

A-MDQL2

A-MA3

C

1

2

0

1

0

.

1

u

F

A-MDQL3

A-MDQU0

A-MA14

A-MDQL1

C

1

2

0

2

1

0

0

0

p

F

A-MDQSLB

A-MA4

A-MRESETB

A-MDQL4

A-MDML

R

1

2

0

1

1

K

1

%

A-MVREFDQ

A-MRESETB

A-MCKB

A-MDQU7

A-MODT

A-MA5

A-MDQU4

A-MCKE

A-MDQL3

A-MDMU

A-MA13

A-MVREFCA

R

1

2

0

2

1

K

1

%

A-MBA2

A-MDQL4

A-MDQU2

A-MBA1

A-MDQSLB

R

1

2

0

5

1

K

1

%

A-MDQU2

R1203

2401%

A-MDQSU

R123110K

A-MBA0

A-MDQU1

A-MDQU5

A-MA5

A-MRASB

A-MDQU1

A-MDQSL

A-MDQSUB

A-MA9A-MA9

R

1

2

3

5

5

6

1

%

A-MDQSL

A-MDQU3

C

1

2

0

4

1

0

0

0

p

F

A-MCKE

A-MVREFDQ

A-MDML

A-MA10 A-MA10

A-MDQU0

A-MA4

A-MA13

A-MBA1A-MBA0

A-MDQU3

A-MA11

A-MDQL6

A-MCK

A-MDQU6

A-MA2

A-MA12

A-MDQSUB

C

1

2

0

3

0

.

1

u

F

A-MWEB

A-MA8

A-MRASB

A-MVREFCA

A-MDQL5

A-MA0

A-MDQU4A-MDQU5

A-MDQL7

A-MDQU6

A-MA6

A-MA0

A-MDQL6

A-MA3

A-MCKB

A-MA7

A-MDQL1

A-MA11

A-MA1

A-MA6

A-MCK

R

1

2

0

4

1

K

1

%

+1.5V_DDR

C

1

2

0

6

0

.

1

u

F

C1209

0.01uF50V

C

1

2

3

9

0

.

1

u

F

C1213 0.1uF

C1208 0.1uF

C1211 0.1uF

C1214 0.1uF

C1212 0.1uF

C1210 0.1uF

C1215 0.1uF

C1207 0.1uF

H5TQ2G63DFR-PBC IC1201

DDR_1600_2G_HYNIX

EAN61829203

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

K4B2G1646E-BCK0 IC1201-*1

DDR_1600_2G_SS

EAN61848802

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

NT5CB128M16FP-DI IC1201-*2

DDR_1600_2G_NANYA

EAN61859702

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_6M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_5T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

H5TQ1G63EFR-PBC IC1201-*3

DDR_1600_1G_HYNIX

EAN61829003

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

NC_7T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

K4B1G1646G-BCK0IC1201-*4

DDR_1600_1G_SS

EAN61836301

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

IC101MSD804KKX

S7LR-M_NON_MS10A_DDR3_A[0]

A11

A_DDR3_A[1]C14

A_DDR3_A[2]B11

A_DDR3_A[3]F12

A_DDR3_A[4]C15

A_DDR3_A[5]E12

A_DDR3_A[6]A14

A_DDR3_A[7]D11

A_DDR3_A[8]B14

A_DDR3_A[9]D12

A_DDR3_A[10]C16

A_DDR3_A[11]C13

A_DDR3_A[12]A15

A_DDR3_A[13]E11

A_DDR3_A[14]B13

A_DDR3_BA[0]F13

A_DDR3_BA[1]B15

A_DDR3_BA[2]E13

A_DDR3_MCLKC17

A_DDR3_MCLKZA17

A_DDR3_MCLKEB16

A_DDR3_ODTE14

A_DDR3_RASZB12

A_DDR3_CASZA12

A_DDR3_WEZC12

A_DDR3_RESETF11

A_DDR3_DQSLB19

A_DDR3_DQSLBC18

A_DDR3_DQSUB18

A_DDR3_DQSUBA18

A_DDR3_DQMLE15

A_DDR3_DQMUA21

A_DDR3_DQL[0]D17

A_DDR3_DQL[1]G15

A_DDR3_DQL[2]B21

A_DDR3_DQL[3]F15

A_DDR3_DQL[4]B22

A_DDR3_DQL[5]F14

A_DDR3_DQL[6]A22

A_DDR3_DQL[7]D15

A_DDR3_DQU[0]G16

A_DDR3_DQU[1]B20

A_DDR3_DQU[2]F16

A_DDR3_DQU[3]C21

A_DDR3_DQU[4]E16

A_DDR3_DQU[5]A20

A_DDR3_DQU[6]D16

A_DDR3_DQU[7]C20

B_DDR3_A[0]B23

B_DDR3_A[1]D25

B_DDR3_A[2]F22

B_DDR3_A[3]G22

B_DDR3_A[4]E24

B_DDR3_A[5]F21

B_DDR3_A[6]E23

B_DDR3_A[7]D22

B_DDR3_A[8]D24

B_DDR3_A[9]D21

B_DDR3_A[10]C24

B_DDR3_A[11]C25

B_DDR3_A[12]F23

B_DDR3_A[13]E21

B_DDR3_A[14]D23

B_DDR3_BA[0]G20

B_DDR3_BA[1]F24

B_DDR3_BA[2]F20

B_DDR3_MCLKG25

B_DDR3_MCLKZG23

B_DDR3_MCLKEF25

B_DDR3_ODTD20

B_DDR3_RASZB25

B_DDR3_CASZB24

B_DDR3_WEZA24

B_DDR3_RESETE20

B_DDR3_DQSLK24

B_DDR3_DQSLBK25

B_DDR3_DQSUJ21

B_DDR3_DQSUBJ20

B_DDR3_DQMLH24

B_DDR3_DQMUL20

B_DDR3_DQL[0]L23

B_DDR3_DQL[1]J24

B_DDR3_DQL[2]L24

B_DDR3_DQL[3]J23

B_DDR3_DQL[4]M24

B_DDR3_DQL[5]H23

B_DDR3_DQL[6]M23

B_DDR3_DQL[7]K23

B_DDR3_DQU[0]G21

B_DDR3_DQU[1]L22

B_DDR3_DQU[2]H22

B_DDR3_DQU[3]K20

B_DDR3_DQU[4]H20

B_DDR3_DQU[5]L21

B_DDR3_DQU[6]H21

B_DDR3_DQU[7]K21

NT5CB64M16DP-DHIC1201-*5

DDR_1600_1G_NANYA

EAN61859501

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12N7

NC_6T3

NC_5M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_7T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

C120510uF10VC122710uF10V

C

1

2

5

1

1

0

u

F

1

0

V

C

1

2

1

7

1

u

F

C

1

2

1

8

1

u

F

C

1

2

1

9

1

u

F

C

1

2

3

8

1

u

F

C

1

2

4

1

1

u

F

+1.5V_DDR +1.5V_DDR

+1.5V_DDR

+1.5V_DDR

CLose to Saturn7M ICCLose to DDR3

SYMBOL.B



THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. REAR_JACK_EU_OS_ERRC_LN52

2013/03/07

66

NC4_S7LRM

JK2801PSC008-01

EU

1AUDIO_R_OUT

2AUDIO_R_IN

3AUDIO_L_OUT

4AUDIO_GND

5B_GND

6AUDIO_L_IN

7B_OUT

8ID

9G_GND

10D2B_IN

11G_OUT

12D2B_OUT

13R_GND

14RGB_GND

15R_OUT

16RGB_IO

17SYNC_GND1

18SYNC_GND2

19SYNC_OUT

20SYNC_IN

21COM_GND

22AV_DET

C28170.1uF50V

EU

R2804470K

R281310K

EU

SC1_G+/COMP1_Y+

SC1/COMP1_L_IN

R2805470K

SCART1_Rout

R28173.9K

EU

R2857220KEU

R281912K

EU

IC2801AZ4580MTR-E1

EU

3IN1+

2IN1-

4VEE

1OUT1

5 IN2+

6 IN2-

7 OUT2

8 VCC

R280810K

EU

R286810K

EU

C282333pF

EU R2864470K

OPT

R281415K

EU

R286910K

EU

SCART1_MUTE

SC1_ID

D281420V

ESD_SCART

R281210K

EU

SC1_FB

R281522

EU

DTV/MNT_L_OUT

D28085.6V

ESD_SCART

+3.5V_ST

R280375

R280775

EU

R28625.6K

EU

D281120V

ESD_SCART

R2858220K

EU

R28101K

EU

D28155.6V

ESD_SCART

DTV/MNT_L_OUT

R281675

EU

R28612.2K

EU

R281812K

EU

D281020V

ESD_SCART

DTV/MNT_R_OUT

D28175.6V

ESD_SCART

SCART1_Lout

D28195.6V

ESD_SCART

R281175

EU

R280275

D281220V

ESD_SCART

+12V

C2820330pF

EU

D281620V

ESD_SCART

SC1_R+/COMP1_Pr+

D28185.6V

ESD_SCART

R286733K

EU

R28602.2K

EU

R28635.6K

EU

DTV/MNT_L_OUT

C2819330pFEU

SC1/COMP1_R_IN

+3.3V_Normal

AV_CVBS_DET

R286633K

EU

R280675

DTV/MNT_R_OUTC282110uF16V

EU

R2865470K

OPT

D281320V

ESD_SCART

C282210uF16V

EU

DTV/MNT_R_OUT

SC1/COMP1_DET

C282433pF

EU

SC1_B+/COMP1_Pb+

4.7uFC2810EU

C28110.1uF

EU

DTV/MNT_VOUT

C28090.1uF

EU

+3.3V_Normal

SC1_SOG_IN

C280147pF50V

EU

SC1_CVBS_IN

0R2801EU

C28160.1uF

SCART_MUTER28402K

SCART_MUTE

R28392K

SCART_MUTE

R284410K

SCART_MUTE

Q2804MMBT3906(NXP)

SCART_MUTE

1

2

3

MMBT3904(NXP)Q2803

SCART_MUTE

MMBT3904(NXP)Q2802

SCART_MUTE

IC2802MM1756DURE

EU

3BIAS

2GND

4OUT

1IN

6VCC

5PS

C28251000pF50V

OPT

C28261000pF50V

OPT

D2826ZENER

ESD_SCART

D2827ZENER

ESD_SCART

FULL SCART

CLOSE TO MSTAR

SCART AMP

[SCART AUDIO MUTE]FULL SCART

CLOSE TO MSTAR

COMPONENT & AV NOT USE TP(LN52)




2012/11/28

Adapter_HDMI_R2_LN52 67

NC4_S7LRM

CK-_HDMI2

R829 100

+5V_Normal

DDC_SDA_2

D801ESD_HDMI

R830 100

D812ESD_HDMI

D809ESD_HDMI

D1+_HDMI2

HDMI_CEC

D804MMBD6100

A

2

C

A

1

D2+_HDMI2

DDC_SCL_2

D1-_HDMI2

R80610K

CK+_HDMI2

R811100

D0-_HDMI2

HPD2

D811

ESD_HDMI

DDC_SCL_2

DDC_SDA_2

R80410K

D820-*1IP4283CZ10-TBA

ESD_HDMI_NXP

3GND_1

2TMDS_CH1+

4TMDS_CH2-

1TMDS_CH1-

5TMDS_CH2+

6NC_1

7NC_2

8GND_2

9NC_3

10NC_4

JK801

E

A

G

5

9

0

2

3

3

0

2

14 NC

13 CE_REMOTE

5D1_GND

20

SHIELDGND

12 CK-

11 CK_GND

2D2_GND

19 HP_DET

18 5V

10CK+

4D1+

1D2+

17 GND

9D0-

8D0_GND

3D2-

16 DDC_DATA

7D0+

6D1-

15 DDC_CLK

R8021K

R812

2.7K

D810

ESD_HDMI

D821-*1IP4283CZ10-TBA

ESD_HDMI_NXP

3GND_1

2TMDS_CH1+

4TMDS_CH2-

1TMDS_CH1-

5TMDS_CH2+

6NC_1

7NC_2

8GND_2

9NC_3

10NC_4

D820RCLAMP0524PA

ESD_HDMI_SEMTECH

1

82

7

3

645

910

D2-_HDMI2

HDMI_CEC

D0+_HDMI2

HDMI_ARC

R8050

HDMI1_ARC

R8031.8K

5V_HDMI_2

D821RCLAMP0524PA

ESD_HDMI_SEMTECH

1

82

7

3

645

910

R813

2.7K

CEC_REMOTE_S7

R8013.3K

5V_DET_HDMI_2

D808ESD_HDMI

D813ESD_HDMI

Q801MMBT3904(NXP)

E

B

C

5V_HDMI_2

MHL_CD_SENSE

MHL_OCP_EN

/VBUS_EN

AVDD5V_MHL

5V_DET_HDMI_4

/MHL_OCP_DET

VA803

ESD_HDMI

DDC_SDA_1

CK+_HDMI1

VA804

ESD_HDMI

HPD1

R80910K

D800-*1IP4283CZ10-TBA

ESD_HDMI_NXP

3GND_1

2TMDS_CH1+

4TMDS_CH2-

1TMDS_CH1-

5TMDS_CH2+

6NC_1

7NC_2

8GND_2

9NC_3

10NC_4

VA800ESD_HDMI

VA806ESD_HDMI

R8071.8K

R8083.3K

HDMI_CEC

VA801ESD_HDMI

D2-_HDMI1

D1-_HDMI1

D2+_HDMI1

R814 100

5V_HDMI_1

CK-_HDMI1

D800RCLAMP0524PA

ESD_HDMI_SEMTECH

1

82

7

3

645

910

5V_DET_HDMI_1

D0-_HDMI1

D802-*2IP4283CZ10-TBA

ESD_HDMI_NXP

3GND_1

2TMDS_CH1+

4TMDS_CH2-

1TMDS_CH1-

5TMDS_CH2+

6NC_1

7NC_2

8GND_2

9NC_3

10NC_4

R8001K

D0+_HDMI1

VA802ESD_HDMI

D1+_HDMI1

D802RCLAMP0524PA

ESD_HDMI_SEMTECH

1

82

7

3

645

910

Q800MMBT3904(NXP)

E

B

CR81010K

R815 100

JK800

E

A

G

5

9

0

2

3

3

0

2

14 NC

13 CE_REMOTE

5D1_GND

20

SHIELDGND

12 CK-

11 CK_GND

2D2_GND

19 HP_DET

18 5V

10CK+

4D1+

1D2+

17 GND

9D0-

8D0_GND

3D2-

16 DDC_DATA

7D0+

6D1-

15 DDC_CLK

DDC_SCL_1

R817

2.7K

D803MMBD6100

A

2

C

A

1

+5V_Normal

DDC_SDA_1

5V_HDMI_1

R818

2.7K

DDC_SCL_1

HDMI_1(ARC)HDMI(REAR 2 Without MHL)

CEC EU NOT USED TP (LN52_ERRC)SIDE HDMI DELETE MHL DELETE

HDMI_2



TH

E

R

M

A

L

THERMAL

T

H

E

R

M

A

L

T

H

E

R

M

A

L

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. Adapter Power

2013/04/17

68

NC4_S7LRM

Q407MMBT3904(NXP)

E

B

C

R4910

C4483300pF

50V

IC407AP7173-SPG-13 HF(DIODES)

3VCC

2PG

4EN

1IN

5GND

6SS

7FB

8OUT

9

[EP]

C4220.1uF16V

OPT

R44175K1/16W1%

C424330pF50V

IC403TPS54319TRE

1VIN_1

3GND_1

7

C

O

M

P

9 SS/TR

10 PH_1

11 PH_2

12 PH_3

1

3

B

O

O

T

1

4

P

W

R

G

D

1

5

E

N

1

6

V

I

N

_

3

5

A

G

N

D

8

R

T

/

C

L

K

6

V

S

E

N

S

E

4GND_2

2VIN_2 17

E

P

[

G

N

D

]

Q403AO3435

FET_2.5V_AOS

G

DS

+3.3V_Normal

PANEL_VCC

Q409AO3407A

G

DS

R402300

RESET_IC_SOC_RESET

R4574.3K1/16W1%

R4174.7K

OPT

+1.5V_DDR

R432330K

R46210K

R43010K

C4400.1uF16V

Q400MMBT3904(NXP)

E

B

C

C417-*110uF10V

CAP_10uF_X7R

R48910K

+3.5V_ST

R43933K

R45327K1%

R4452.2K

C4470.33uF16V

R44310K

+12V

+3.5V_ST

R46110K

OPT

R4405.6K

R488100K

C403-*110uF 10V

CAP_10uF_X7R

R42810K

C4110.1uF16V

C426100pF50V

OPT

R410100K

C4410.1uF16V

C4130.047uF

25V

L403BLM18PG121SN1D

C4440.1uF16V

+3.3V_Normal

Q403-*1DMP2130L

FET_2.5V_DIODE

G

DS

IC408NCP803SN293

PWR_DET_ON_SEMI

1GND

3VCC 2 RESET

560pFC467

50V

R41410K

+12V

+5V_Normal

POWER_ON/OFF_1

+1.10V_VDDC

POWER_DET

RL_ON

C42022uF16V

IC408-*1APX803D29

PWR_DET_ON_DIODES

1GND

3 VCC2RESET

+3.3V_Normal

R454

11K 1%

R4564.7K

1/16W1%

+3.5V_ST

+3.3V_Normal

USB1_CTL

R43822K

R43310K

R43615K

+3.5V_ST

C4250.1uF16V

PANEL_CTL

+5V_USB

R43410K

R4092K1%

+3.5V_ST

POWER_DET_RESET

USB1_OCD

R46310K

RESET_IC_SOC_RESET

+3.3V_Normal

L420BLM18PG121SN1D

+5V_Normal

+2.5V_Normal

C4740.1uF

R4055.6K

C4194.7uF 10V

C4883300pF

R44230K1/16W1%

C40510uF16V

C4103300pF50V

C439

100pF50V

R4075.6K

C42122uF16V

OPT R45233K1%

C4760.1uF16V

L4063.6uH

L4153.6uH

C40310uF10V

CAP_10uF_X5R

85C

C41710uF10V

CAP_10uF_X5R

85C

R402-*1100

+3.5V_SOC_RESET

IC401TPS65281RGV

3

R

O

S

C

2

C

O

M

P

4

R

L

I

M

1

S

S

5

EN_SW

6

FAULT

7

AGND

8

SW_OUT

9

S

W

_

I

N

1

0

F

B

1

1

L

X

1

2

B

S

T

1

3

PGND

1

4

VIN

1

5

V7V

1

6

EN

1

7

[EP]

IC402TJ1118S-2.5

1GND

2 OUT3IN

C43722uF10V

C43010uF10V

10uFC461

10V

C4232.2uF10V

C45322uF10V

C45622uF10V

C44310uF16V

C47222uF10V

D4025V

OPT

D4055V

+24V_ADAPTER

+3.5V_ST

C4270.01uF

50V

R42612K

Q405AO3407A

G

D

S+24V

POWER_ON/OFF_1

R42710K

C4290.01uF

50V

C4182.2uF50V

R42510K

Q404MMBT3904(NXP)

E

B

C

R42410K

OPT

+24V_ADAPTER

L4074.7uH

C414150pF50V

C4360.1uF

16V

C4080.01uF

50V

R41910K

C40110uF35V

D401

40VB540C

L404BLM18PG121SN1D

C4060.1uF50V

C4490.1uF16V

IC404RT8289GSP

3NC_2

2NC_1

4FB

1BOOT

5EN

6GND

7VIN

8SW

9

[EP]GND

+24V_ADAPTER

+12V

+24V_LED_DRIVER

R40811K1%

R415100K 1%

L4056.8uH

C43347pF50V

IC400TPS54331D

3EN

2VIN

4SS/TR

1BOOT

5VSENSE

6COMP

7GND

8PH

C4424700pF50V

C43522uF10V

C4020.1uF50V

D40040V

C40010uF35V

R42020K

C4501000pF50V

OPTC4090.01uF50V

C4310.1uF16V

L400BLM18PG121SN1D

+24V_ADAPTER

C4460.1uF16V

+3.5V_ST

+3.3V_Normal

R44410K

WLED_ENABLE

Q410MMBT3904(NXP) E

B

C

R44610K

R4371K

INV_CTL

R400330K

R41268K

R41316K1%

C42810uF35V

R493100

L410BLM18PG121SN1D

POWER_ON/OFF_1

R421180K1%

R42356K1%

L401CB2012PK501T

L413CB2012PK501T

L412UBW2012-121F

L421UBW2012-121F

+24V_ADAPTER +12V

R4502.7K1%

PD_+12V

R4961.2K1%

PD_+12V

C49022uF10V

D4065V

OPT

C49122uF10V

R49427K1%

PD_+24V_ADAPTER

R4955.1K1%

PD_+24V_ADAPTER

D4032.5V

OPT

D4042.5V

OPT

JK400KJA-DC-1-0032

1

2 2

4 4

C43422uF16V

C43222uF16V

C44510uF16V

+12V -> PANEL_VCC

+3.3V_Normal -> +2.5V_Normal

+3.5V_ST -> +1.10V_VDDC S7LRM core

CHANGE TO16V/X5R

R1

PD_+12V --> 3.69V

CHANGE TO10UF/10V/X5R

+3.5V_ST -> +3.3V_Normal

CHANGE TO10UF/10V/X5R

Vout=0.8*(1+R1/R2)=1.5319

+12V -> +5V_Normal & +5V_USB

+3.5V_ST -> +1.5V_DDR

R2

Vout=0.827*(1+R1/R2)=1.1578V

R2

Power_DET

R1

R1

PD_+24V_ADAPTER --> 3.81V

Vout=0.8*(1+R1/R2)=5.236V

R21.5A

L13 Adapter POWER BLOCK

AO3407A Vgs : 10.8V(24V input)

AMP_VCC

+24V_AMP_VCC

+24V_ADAPTER -> +12V

+24V_ADAPTER -> +3.5V_ST

5A

Vout=1.222*(1+R1/R2)=12.33V

R1

R2

3A3A

R2

Vout=0.8*(1+R1/R2)=3.37V

3A

R1

1AINV_CTL

ADAPTER JACK




D69001N4148W

IC6900MAP3202SIRH

3GATE

2VCC

4GND

1EN

6RT

5CS

7SYNC

8REF

9PWMO

10OVP

11PWMI

12COMP

13FBP

14FBN

+24V_LED_DRIVER

R69231K

R691610K1%

C69010.1uF50V

+12V

PWM_DIM

R690110

R6926100K

R691775K

R69211K

R69251K

D69021N4148W

WLED_ENABLE

R6922OPT

R690710K

R691122K1%

32inch_Adapter

C69060.47uF

16V

Q6902-*1STN4NF20L

42inch_Adapter

S

GD

R6911-*112K1%

42inch_Adapter

R69323.91%

R69343.91%

R69303.91%

R69283.91%

R69274.31%

R69314.31%

R69294.31%

R69334.31%

R6915-*175K1%

42_ROW_Adapter

R691551K1%

32_Adapter/42_POLA_Adapter

R6904430K1%

Documents

LG+32LN520B+Ch+LD36M+LED+TV