Upload
repartout
View
94
Download
0
Embed Size (px)
DESCRIPTION
Service manual
Citation preview
PLASMA TVSERVICE MANUAL
CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : RF-043B
MODEL : RZ-42PX10/11
website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html
- 2 -
CONTENTS
SAFETY PRECAUTIONS ...................................................................................3
DESCRIPTION OF CONTROLS ........................................................................ 4
SPECIFICATIONS ............................................................................................ 13
ADJUSTMENT INSTRUCTIONS ......................................................................15
TROUBLE SHOOTING GUIDE..........................................................................18
BLOCK DIAGRAM.............................................................................................29
EXPLODED VIEW..............................................................................................32
EXPLODED VIEW PARTS LIST ........................................................................33
REPLACEMENT PARTS LIST...........................................................................34
SCHEMATIC DIAGRAM ........................................................................................
PRINTED CIRCUIT BOARD ..................................................................................
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.
It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.
When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
- 4 -
DESCRIPTION OF CONTROLS
- When using the remote control aim it at the remote control sensor of the set.- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
MULTIMEDIASelects the Component, RGB or DVI
modes.
PIP/DWSwitches the sub picture on or off.
Selects PIP or DW modes.PIP PR + /-
Selects a programme for the sub picture.SWAP
Alternates between main and sub pic-ture.
PIP INPUTSelects the input mode for the sub pic-
ture.WIN.SIZE
Adjusts the sub picture size.POSITION
Moves the sub picture to DD / EE or FF / GGdirection.
POWERswitches the set on from standby oroff to standby.
ARC Changes the picture format.
MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.
SWAPReturns to the previously viewedprogramme.Note : This function works onlywhen Favorite programme is set to Off.Otherwise each press of this buttonwill select a stored favorite pro-gramme.
SSMTo select the sound appropriate toyour viewing programme character.
NUMBER buttons
SLEEPSets the sleep timer.
I/IISelects the language during dual lan-guage broadcast.Selects the sound output.
TEXTThese buttons are used for teletext.For further details, see the ‘Teletext’section.Note : In teletext mode, the PIP PR+/-, SWAP and PIP INPUT buttons areused for teletext function.
LISTDisplays the program table.
TV/AVSelects the TV, AV, Component, RGB
or DVI modes.
MUTESwitches the sound on or off.
DD / EE (Programme Up/Down)selects a programme or a menu item.
switches the set on from standby.FF / GG (Volume Up/Down)
adjusts the volume.adjusts menu settings.
OKaccepts your selection or displays the
current mode.
PSMAdjusts the factory preset picture
according to the room.
SPLIT ZOOMEnlarge the screen with regular
ration.
- 5 -
<Front Panel Controls>
ON/OFF
TV/AV MENU VOL PR
TV/AV MENU VOL PR
- Shown is a simplified representation of the set.- Here shown may be somewhat different from your set.
Main Power Button
Remote Control Sensor
TV/AV ButtonSelects the TV, AV, Component,RGB or DVI modes. If OSD is dis-played, selects menu item.
MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.
DD / EE (Programme Up/Down)selects a programme or a menu item.
switches the set on from standby.FF / GG (Volume Up/Down)
adjusts the volume.adjusts menu settings.
Power Standby IndicatorIlluminates red in standbymode, Illuminates greenwhen the set is turned on
or
- 6 -
<Back Panel>
AntennaREMOTECONTROL
S-V
IDE
OV
IDE
OA
UD
IO
RS-232C INPUT DVI INPUT(CONTROL/SERVICE)
AC INPUTAUDIO INPUT RGB INPUT
Y PB PR L R
L(MONO) R
COMPONENT
S-VIDEO VIDEO AUDIO
AUDIO
AV4
AV1
AV5
AV2 AV3
RL/
MO
NO
1. REMOTE CONTROL
2. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.
3. DVI INPUT / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER to this socket.
4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.
AUDIO/VIDEO IN SOCKETS (AV4)Connect the audio/video out sockets of external equipment tothese sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in AV4.
5. ANTENNA INPUT
6. EURO SCART SOCKETConnect the euro scart socket of the VCR to these sockets.
7. POWER CORD SOCKETThis Monitor operates on an AC power. The voltage is indi-cated on the Specifications page. Never attempt to operatethe Monitor on DC power.
8. AUDIO/VIDEO IN SOCKETS (AV5)S-VIDEO/AUDIO IN SOCKETS
3 4 5 6
8
71 2
- 7 -
- Be careful for the bronze wire not to be bended in connecting to antenna input port.
Antenna Connection
AntennaTEOL
RS-232C INPUT DVI INPUT(CONTROL/SERVICE)
AC INPUTAUDIO INPUT RGB INPUT
Y PB PR L R
L(MONO) R
COMPONENT
S-VIDEO VIDEO AUDIO
AUDIO
AV4
AV1 AV2 AV3
Watching VCR- When connecting the set to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white, Audio
(R) -red).- Connect the VIDEO INPUT socket (yellow) to the VIDEO INPUT on the set.- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR
to the Video input. Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
- Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still pic-ture from a VCR. (Refer to p. 25)If a 4:3 picture format is used; the fixed image may remain visible on the screen.
- To avoid picture noise (interference), leave an adequate distance between the VCR and set.
Watching TV programmes- Turn the set on and select the programme you
want.
Watching VCR1. Use the TV/AV button on the remote control to
select AV1, AV2, AV3, AV4 or AV5.- If both S-VIDEO and VIDEO sockets have been
connected to the S-VHS VCR simultaneously, onlythe S-VIDEO can be received.
2. Insert a video tape into the VCR and press thePLAY button on the VCR.(See VCR owner’s manual)
Apartments(connecting to wall antenna socket)
Private house(connecting to wall outdoor antenna)
outdoor antenna
wall antenna socket
VHF antenna
UHF antenna
RF coaxial wire (75 ohms)< Back panel of the set >
< Back panel of the set >
< VCR >
- 8 -
Watching Cable TV- After subscribing for a local cable TV station and installing a converter you can watch cable TV.- For further information of cable TV, contact the local cable TV station.
To watch cable TV
1. Use the TV/AV button on the remote control toselect AV1, AV2, AV3, AV4 or AV5.
2. Tune to cable service provided channels usingthe cable box.
Watching external AV source- When connecting the set to an external source, match the colours of AUDIO/VIDEO input jacks on the set with the output jacks
on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
How to use1. Use the TV/AV button on the remote control to
select AV1, AV2, AV3, AV4 or AV5.2. Operate the corresponding external equipment.
See external equipment operating guide.
R LAUDIO VIDEO
R
< Back panel of the set >
< Cable box >
< Back panel of the set >
Camcorder
Video game set
- 9 -
Watching DVD
How to connectConnect DVD video outputs to Y, PB, PR of COMPO-NENT INPUT and audio outputs to Audio sockets ofAUDIO INPUT.
How to use1. Turn on the DVD player, and insert a DVD.2. Use TV/AV or MULTIMEDIA button on the remote
control to select Component. Refer to the DVD player'smanual for operating instructions.
• Component Input portsYou can get better picture quality if you connectDVD player with component input ports as below.
Component ports of theset
Y PB PR
Video output ports of DVD player
YYYY
PbB-YCbPB
PrR-YCrPR
AntennaOTEROL
RS-232C INPUT DVI INPUT(CONTROL/SERVICE)
AUDIO INPUT RGB INPUT
Y PB PR L R
L(MONO) R
COMPONENT
S-VIDEO VIDEO AUDIO
AUDIO
AV4
R
RR
R
< Back panel of the set >
< DVD player >
- 10 -
Connecting PC- To enjoy vivid picture and sound, connect a PC to the set.- Avoid keeping a fixed image on the set’s screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.- Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of
PC accordingly.- There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC
mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until thepicture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to themanufacturer of the PC graphic card.
- The synchronization input form for Horizontal and Vertical frequencies is separate.
Setup Instructions to Connect a PC to your set- We recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.- If the resolution of PC is over UXGA, there will be no picture on the set.- Connect the signal cable from the set output port of the PC to the RGB INPUT port of the set or the signal cable from the DVI out-
put port of the PC to the DVI INPUT port on the set.- Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).- If using a sound card, adjust PC sound as required.- This set apply a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts
automatically to use this set.- DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode.- If required, adjust the set settings for Plug and Play functionally.- If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI
INPUT to display the PC on the set.If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other modeis set to Plug and Play automatically by the set.)
- DOS mode may not work depending on video card if using a DVI-I cable.
An32C INPUT DVI INPUTROL/SERVICE)
AUDIO INPUT RGB INPUT
Y PB PR L R
L(MONO) R
COMPONENT
S-VIDEO VIDEO AUDIO
AUDIO
AV4
PC Setup1. Turn on the PC and apply power to the set.2. Turn on the display by pressing the POWER button on
the set’s remote control.3. Use the TV/AV or MULTIMEDIA button on the remote
control to select the RGB or DVI input source.4. Set the resolution output of the PC to SXGA or under
(1280 x 1024, 60Hz). (Refer to p. 13)
< Back panel of the set >
- 11 -
RGB / DVI mode
Resolution
640x350
720x400
640x480
848x480
800x600
HorizontalFrequency(KHz)
VerticalFrequency(Hz)
852x480
832x624
1024x768
1152x864
1152x870
1280x960
1280x1024
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.500
37.799
39.375
31.500
37.799
39.375
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.677
54.348
63.995
67.500
77.487
68.681
60.023
63.981
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
56.25
60.31
72.18
75.00
85.06
74.55
60.00
70.06
75.02
85.00
60.05
70.01
75.00
85.00
75.06
60.02
60.02
- 12 -
D-sub 15 pin cable
AS mark
LG TV
Owner’s Manual
1.5V1.5V
Alkaline batteries
Power Cord
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
Remote Control handset
DVI-D Cable
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.
- Contract your dealer for buying these items.
Optional Extras
Tilt wall mounting bracket
404250 40 42 50
Video cables Audio cablesCeiling mounting bracket
40
4250
42
40
- Secure the TV assembly by attaching it to a wall for additional support.
Attaching the TV assembly to the wall
• Install the TV brackets on the TV as shown.Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the prod-uct), as shown.Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely.
• Secure the TV assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.
2-TV brackets2-Wall brackets
2-TV bracket bolts
- 13 -
SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.
V Application RangeThis spec is applied to the 42”PDP TV used RF-043B Chassis.
V Specification
Each part is tested as below without special appointment.1) Temperature : 25¡ 5°C (77¡ 9°F)2) Relative Humidity: 65¡ 10%3) Power Voltage: Standard Input voltage (100V~240V@ 50/60Hz)
* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in
accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.
V Test and Inspection Method1) Performance : LGE TV test method followed.2) Demanded other specification
Safety: CE, IEC specificationEMC : CE, IEC
V General Specification
1. General Specification
Appliance
TEST
TEST
Remark
Safety : IEC/EN60095
EMI : EN55013
EMS : EN55020
Safety : IEC60065
EMI : CISPR13
Model Name
RT-42PX10
RZ-42PX10
Market
EU
Non-EU
Chassis
RF-043B
Brand
LG
LG
Model Name
RZ-42PX10
RT-42PX10
Market Place
EU
Non-EU
Remark
PDP
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Murata / Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42V6xxxx, RGB Closed Type
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
AC100 ~ 240V, 50/60Hz
No
1
2
3
4
5
6
7
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
2. Model Specification
(1) RZ-42PX10
(2) RT-42PX10
Item
Market
Broadcasting
Receiving system
Scart Jack ( 3EA )
Video Input(2EA)
S-Video Input(2EA)
Component Input(1EA)
RGB Input(1EA)
DVI Input(1EA)
Audio Input(4EA)
Wired Control
Specification
EU
PAL B/G/I/D/K, SECAM L/L
Upper Heterodyne
PAL, SECAM
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC
DVI-PC
PC Audio, Component,AV(2EA)
Discrete IR
Remark
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
DVI-D
L/R Input
- 14 -
No
8
9
10
11
12
13
14
15
16
17
18
Remark
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
4 System :
PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60
DVI-D
L/R Input
Specification
Non-EU
PAL B/G/I/D/K, NTSC
Upper Heterodyne
PAL, SECAM, NTSC
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC
RGB-DTV(for Austrailian)
DVI-PC
PC Audio, Component,AV(2EA),
AV(2EA)
Discrete IR
No
19
20
21
22
23
24
25
26
27
28
29
Item
Market
Broadcasting
Receiving system
Video Input(2EA)
Video Output(1EA)
S-Video Input(2EA)
Component Input(2EA)
RGB Input
DVI Input
Audio Input(5EA)
Wired Control
- 15 -
1. Application RangeThe spec sheet is applied all of the 42”PDP TV, RF-043Bchassis by manufacturing LG TV Plant or sort plants.
2. Specification(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolationtransformer will help protect test instrument.
(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.
(4) The input voltage of the receiver must keep 100~220V,50/60Hz.
(5) The receiver must be operated for about 15 minutes priorto the adjustment.
O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.
O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE
PATTERN.
[ Set is activated HEAT-RUN without signal generator inthis mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.
Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), a afterimage may be occur in the black level part of thescreen.
3. PCB assembly adjustment method
3-1. Channel memory
(1) Setting up the G-prove1) Install the GProve. (GProve4.4.0.2.exe)2) After installing the Gprobe, [Option -> Connection
Setup] or click the icon indicated in the picture and thensetup as below the picture.(In case of the port (second one), set to the serial port of the connected PCThe other only have to be set as below the picture.)
3) After finishing inputs, click the button [OK] to completethe connection setup.
(2) Confirming the G-prove1) Connect Rs232 cable and then turn on the power.
if communication is correct, the message is showed like in the left output terminal.
2) If the message is not showed, push the [INSTART]button of the adjust remocon twice, and change theright selection of the [System Control -> RS-232 Host]from GProbe to PC.** If it is impossible to check the OSD, push the [TILT]
button of the adjust remocon.Then, the message which is “Starting Gprove...” comes up. From this time, communication is operated correctly.However, you have to push the [TILT] button again in case of turning on Main Power.
** If you want to check again whether communication ison or not, input “test” and push the Enter key on theright input terminal. If communication is on, themessage of “Test passed.” will come up
(3) Channel memory method1) Click [Command -> Batch].2) When the window of [Batch] is showed, enter the text file
(Ch_Memory-RZ_PX10.txt) in the right blank of the File.3) Click the button [OK] to write CH information in the
EEPROM.4) It means the completion of the CH memory download that
the message of right output terminal is showed as below.
ADJUSTMENT INSTRUCTIONS
fig1
fig2
fig3
3-2. HDCP download
(1) Setting up & Confirming the G-prove: refer to 3-1-(1) and 3-1-(2)
(2) HDCP download method1) Click [Command -> NVRAM Write]2) When the window of [NVRAM Write] is showed, select
“LGEKEY1.bin” to insert fill up in the File.3) LGEKEY1 : first KEY value4) Address : insert ‘0’5) After finishing inputs, click the button [OK] to write
HDCP key in the EEPROM.6) It means the end of the HDCP key download that the
message of Output terminal is showed as below.
4. SET assembly adjustment method
4-1. POWER PCB Assy V oltage Adjustments(Va, Vs Voltage Adjustments)
(1) Test Equipment : D.M.M 1EA
(2) Connection Diagram for Measuring : refer to fig5
(3) Adjustment Method1) Adjustment method of P/No 3501V00180A B/D
1. Va Adjustmenta. After receiving 100% Full White Pattern, HEAT RUN.b. Connect + terminal of D.M.M to Va pin of P805,
connect - terminal to GND pin of P805.c. After turning RV 501, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top (Deviation; ±0.5V)
2. Vs Adjustmenta. Connect + terminal of D.M.M to Vs pin of P805,
connect – terminal to GND pin of P805.b. After turning RV 401, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top. (Deviation; ±0.5V)
2) Adjustment method of P/No 3501V00182A B/D1. Va Adjustment
a. After receiving 100% Full White Pattern, HEAT RUN.b. Connect + terminal of D.M.M to Va pin of P805,
connect - terminal to GND pin of P805.c. After turning RV 601, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top (Deviation; ±0.5V)
2. Vs Adjustmenta. Connect + terminal of D.M.M to Vs pin of P805,
connect – terminal to GND pin of P805.b. After turning RV 401, voltage of D.M.M adjustment
as same as Va voltage which on label of panelright/top. (Deviation; ±0.5V)
4-2. Adjustment of White Balance
(1) Required EquipmentColor Analyzer (CA-100 or same product)
(2) Connection Diagram of Equipment for Measuring
(3) Adjustment of White BalanceO Operate the Zero-calibration of the CA-100, then stick
sensor to PDP module surface when you adjust.O For manual adjustment, it is also possible by the
following sequence.
- 16 -
< 3501V00180A >
< 3501V00182A >
fig5 Connection Diagram of power adjustment for measuring.
fig4
Each PCB Assy must be checked by the Check JIG Set beforewhole assembly. (Be careful the POWER PCB Assy not todamage to PDP Module)
Window
MSPG-2100 orMSTG-5200
AV Signal Input
Full Size pattern
216 gray Level
RS-232C Serial Communication
RZ/RT 50Hz
fig6 White Balance Adjustment
1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operateheat run more than 15 minute.
2) Supply 2 Gray Pattern (216 Level Full Size Pattern)signal to VIDEO input.(RZ-42PX10 : AV4 INPUT 50Hz,RT-42PX10 : AV2 INPUT 50Hz)(refer to Fig6)
3) To adjust, stick sensor to 216 Gray Level Pattern, pressADJ key twice(White Balance) on remote control.For adjustment and D , E on remote control foradjustment mode to select Red Gain and Blue Gain,press VOL +, - Key and adjust it until color coordinationbecomes as below.
X ; 0.283 ± 0.003, Y; 0.297 ± 0.003,Color Temperature; 9,300°K ± 500°K
4) Exit adjustment mode using A Key.
4-3. Auto RGB Color Balance
(1) Pattern Equipment : PC Pattern Generator (VG828, VG854, 801GF, MSP3240A)(16 Gray Scale Pattern output(RGB output Level: 0.7Vp-p)
(2) Method of Auto RGB Color Balance 1) Input RGB Source : 16 Gray Scale Pattern output
(RGB output Level : 0.7Vp-p)2) Press ADJ KEY on R/C for adjustment. 3) Press Vol. + KEY and operate To set.4) Auto-RGB OK means completed adjustment.
4-4. Auto Component Color Balance
(1) Pattern Equipment : MSP3240A or same product(16 Gray Scale Pattern output(Component outputLevel: 0.7Vp-p)
(2) Method of Auto RGB Color Balance 1) Input RGB Source : Component 480p/576p 16 Gray
Scale Pattern outputAt this time, except Pb and Pr signal, only Y signal insert.2) Press ADJ KEY on R/C for adjustment. 3) Press Vol. + KEY and operate To set.4) Auto-RGB OK means completed adjustment
4-5. Auto Adjustment Map(RS-232C)
4-6. DDC Data Input
(1) Required Test Equipment1) A jig for adjusting PC, DDC (PC serial to D-sub
Connection equipment)2) S/W for writing DDC (EDID Data Write & Read)3) D-sub 15P Cable,D-Sub to DVI Connector (Connect to DVI Jack)
(2) Setting of Device
(3) Preparation for Adjustment1) Set devices as above and turn the PC, jig on.2) Put S/W for writing DDC (EDID data Write & Read) into
operation. (operated in DOS mode.)
(4) Sequence of Adjustment1) DDC Data Input for Analog-RGB
1. Put the set on the table and turn the power on.2. Connect PC Serial to D-sub 15P Cable of jig for DDC
adjustment to RGB terminal (D-Sub 15Pin).3. Operate S/W for DDC record and select DDC data for
Analog RGB in Model Menu.4. Operate EDID Write command.5. Operate EDID Read command and check whether
Check Sum is 53.6. If Check Sum is not 53, repeat 3 ~ 4.7. If Check Sum is 53, DDC data for Analog-RGB input
is completed.
2) DDC Data input for Digital-RGB(DVI)1. Connect PC Serial to DVI Cable of jig for DDC
adjustment to DVI terminal (DVI Jack).2. Operate S/W for DDC record and select DDC Data
for digital RGB in Model Menu.3. Operate EDID Write command. 4. Operate EDID Read command and check whether
Check Sum is D2(1page), BF(2page).5. If Check Sum is not D2(1page), BF(2page), repeat 3 ~ 4.6. If Check Sum is D2(1page), BF(2page), DDC data for
Analog-RGB input is completed.
- 17 -
fig7 Auto RGB/ Component Color Balance Test Pattern
Type
Baud Rate
115200
Index
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Data bit
8
Cmd1 Cmd2
j a
j b
j c
j d
j e
j f
Stop bit
1
Parity
NONE
ProtocolSetting
Data Min Value
00(00)
00(00)
00(00)
00(00)
00(00)
00(00)
Max Value
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
RF-043B_PDP42
PCPC
JIGJIG
PDPPDP
SETSET
- 18 -
TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Manufacture enterprisemeaning of a passage
1. Check the Power Offcondition.
Doesn't the screen whole come
out?
It is identical with Power Off
condition?
Yes
Yes
No
No
No
No
No
2. Check the Interfacesignal condition.
Is the Interface signal operated?
Yes
3. Check the St-by 5Vsignal circuit.
Doesn't the low pressure output
come out?
Doesn't the St-by 5V signal
come out?
Yes
Yes
No
4. Check the 5V Monitorsignal circuit.
Doesn't the 5V Monitor signal
come out?
Yes
7. Check the VSC Vs-ONsignal
Doesn't the high tension output
come out?
Doesn't the VSC signal Vs-ON
come out?
Yes
Yes
High tension output voltage Drop
it occurs?
When remove the
Y B/D Module Input Connector, output
voltage Drop it occurs?
When remove the Y, Z B/D Module
Input Connector, Power Board high tension output
voltage Drop it occurs?
Yes No No
9. Check the PowerBoard Output high
tension circuit
Yes
10. Check the Z B/DModule Coutput circuit
Yes
When remove the
Z B/D Module Input Connector, output
voltage Drop it occurs?
11. Check the Y B/DModule Coutput circuit
Yes
No
8. Check the Vs, Vavoltage output circuit.
Doesn't the Vs, Va voltage output
come out?
Yes
No
No
5. Check the VSC RL-ONsignal.
Doesn't the VSC signal RL-ON
come out?
Yes
6. Check the VSC lowpressure output
Doesn't the VSC low pressureoutput come out?
Yes
- 19 -
1-2. Sony Power Board Structure
T502: Vs Trans
T702: Va Trans
T101: St-by Trans
T103: Low Voltage Trans
1 2 3
- 20 -
1-3. Sanken Power Board Structure
T221: Vs Trans
T271: Va Trans
T121: St-by Trans
T201: Low Voltage Trans
1 2 3
- 21 -
2. No Power
(1) Symptom¯ Does’t minute discharge at module. ¯ Non does not come in into the front LED.
(2) Check follow
Is plug in power cord? Plug in power cord.
Yes
No
Is connect the Line Filter and PowerSwitch Cable?
Connect Cable.
Yes
No
Is connect the Power Switch andPower Board Cable?
Connect Cable.
Yes
No
Is normal the Fuse(F101) on PowerBoard?
Replace Fuse.
Yes
No
Is connect the Power Board and 7Pof VSC Board Cable?
Connect Cable.
Yes
No
Is connect the Power Switch andPower Board Cable?
After remove the cable connect toPower Board(except the CN101
connection cable), authorizes theAC voltage marking on manual.
When ST-BY 5V does not operate,replace Power Board.
Connect Cable.
Yes
No
- 22 -
3. Protect Mode
(1) Symptom¯ After once shining, it does not discharge minutely
from module¯ The Rely falls(The sound is audible “click”) ¯ It is converted with the color where the front LED
is red from green.
(2) Check follow
Is normal the PowerBoard?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is normal the eachconnector?
Replaceconnector.
Replace Y-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is normal the Ctrl Board?
Replace X-Board.
Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the Y- Board?
Is normal the outputvoltage after removeP5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
Replace Z-Board.
Is normal the Z- Board?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)
Yes
No Yes
Is normal the X- Board?
Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is normal the VSC Board?
Is normal the output voltage afterremove P1000, P1200?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1000 normal operation:Replace Analog BoardAfter remove P1200 normal operation:Replace Digital Board
Yes
No
Is normal the COF of X, Y, Z?
No
Yes
Yes
- 23 -
4. No Raster
(1) Symptom¯ Does’t minute discharge at module. ¯ It maintains the condition where the front LED is green.
(2) Check follow
Is normal the PowerBoard?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is normal the eachconnector?
Replaceconnector.
Replace Y-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is normal the Ctrl Board?
Replace X-Board.
Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the Y- Board?
Is normal the outputvoltage after removeP5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
Replace Z-Board.
Is normal the Z- Board?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)
Yes
No Yes
Is normal the X- Board?
Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is normal the VSC Board?
Is normal the output voltage afterremove P1000, P1200?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1000 normal operation:Replace Analog BoardAfter remove P1200 normal operation:Replace Digital Board
Yes
No
Is normal the COF of X, Y, Z?
No
Yes
Yes
- 24 -
5. In case of occur strange screen into specific mode
5-1. In case of does’t display the OSD
(1) Symptom¯ LED is green¯ The minute discharge continuously becomes
accomplished from module
(2) Check follow
Is normal the LVDScable?
Is normal the VSCDigital Board?
Is the LVDS cableconnected well?
Cable inserts well.Yes
No
No
Yes
Operates the ThineIC(IC1100)?
Replace ThineIC(IC1100).
No
Is normal the CtrlBoard of Module?
Replace Ctrl B/D.No
No
Operates theIEP(IC500)?
ReplaceIEP(IC500).
Yes
No
Operates theScaler(IC700)?
ReplaceScaler(IC700).
Yes
Replace cable.Yes
- 25 -
5-2. In case of does’t display the screen into specific mode
(1) Symptom¯ The screen does not become the display from specific input mode
(RF, AV, Component, RGB, DVI).
(2) Check follow¯ Check the all input mode should become normality display.¯ Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
(4) In the case of becomes unusual display from RF, AV mode
Is normal the Tuner?
Is normal theCXA2069Q?
Is the Tuner Cableconnected well?
Cable inserts well.
Yes
No
No
Yes
Is normal theVPC3230?
Replace Tuner
No
Is normal the Input voltage, IICCommunication and CVBS output?
Yes
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal theCXA2069Q?
Yes
Is normal theVPC3230?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 26 -
(5) In the case of becomes unusual display from RF, AV, Component 480i mode
(6) In the case of becomes unusual display from Component DTV mode
Is normal theVPC3230?
Yes
Is normal the S2300?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the74LS123?
Yes
Is normal theCXA2101?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal theM52758?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 27 -
(7) In the case of becomes unusual display from RGB DTV mode
(8) In the case of becomes unusual display from RGB PC mode
(8) In the case of becomes unusual display from DVI mode
Is normal theCXA2101?
Yes
Is normal theM52758?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal theM52758?
Yes
Is normal the Scaler?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 28 -
6. In case of no sound
(1) Symptom¯ LED is green¯ Screen display but sound is not output
(2) Check follow
Is normal the SPKcable?
Is the SPK cableconnected well?
Cable inserts well.
No
No
Cable inserts well.
No
Replace IC800
No
Replace IC801
No
Replace SPK cableYes
Yes
Is normal theRGB/DVI sound?
Is the Flat cableconnected well?
No
No
Operates the IC800?Yes
Operates the IC801?
Replace IC802
No
Operates the IC802?Replace
VSC Analog B/D
Yes
Yes
Yes
Is normal theRF/AV/Component
sound?
- 29-
BLO
CK
DIA
GR
AM
RGB(PC/DTV)
DVI(PC/DTV)
RS232
IR 74ACT253
RX0/1,TX0/1
IRTX
SCL/ SDA
RGB H/ V
SCL/ SDA
RX/ TX0/ 1/ 2, RX/ TXC
ST3232C
24LC21
74HCT08
24LC21
CXA2101
Scart1
Scart 2
Scart3
RF
CVBS
S-VHS
CXA2069QSWITCHTuner (M)
Tuner(S)
Vin1 (CVBS)VPC3230 (M)Video Decoder
VPC3230 (S)Video Decoder
1H RGB
Vin2 (CVBS)
MNT OUT
TV OUT
Vin3 (CVBS)
TU_Main
TU_Sub
Vin4
YCin4
Main_V
Main_YC
Main_V
Main_YC
SDA6001Text Processor
Text_V
HYV641620SRAM
AM29LV160F-ROM
74LS123
Comp_480i
M52758FSwitc h
S2300DeInterlac er
YCbCr/8
HY57V64322SDRAM (8MB)
RGB PC/ DTV
RGB PC
RGB DTVgm1601
Sc aler (Malibu)Comp DTV
CXA_RGBRGB_Data
Main_Video/
24Sub_Video
/8
DVI_Data
TX_Out
RS232_RX/ TX
Comp/ RGB_SWFrom Malibu
Dig ital
Analog
Side - AV CVBS S-VHS
Vin5 YCin5Comp_Y
Comp_480I/ PTo Malibu
Video f o r TextText TX0/ 1/ 2/ 3/ CDisp_EnSDATASCLK, SLE
HY5DU283222ASDRAM (128MB)
AM29LVF-ROM (1MB)
Comp/ RGB_SW
Comp_480I/ P
Pos t- p rocessing Block is omit ted .so-c alled JEPICO, in this c aseTMDS TX is also required .Sound Processing Block Diagramis separated . .RCA-type Bloc k Diagram is also separated. .
DVI RXw/ HDCP
ADCw/ PLL
IEP
2424 2424
10
WIRE
ZHINE
Comp1(D D/DTV)V
BOARD
BOARD
BOARD
BLO
CK
DIA
GR
AM
- 30-
RGB(PC/ DTV)
DVI(PC/ DTV)
RS232
IR
ST3232C
74ACT253
74HCT08
Tx
gm1501H24LC21
24LC21
RGB PC
IIS
IIS
IIS CXA2101CXA2101
RGB DTV
HVM52758FPIC202(MUX)M52758FPIC202(MUX)
M52758FPIC204M52758FPIC204
RGB_DTV
FLI2300FLI2300HY57V64322 SDRAM (8MB)HY57V64322 SDRAM (8MB)
DAC_RGB
Comp1(DVD/ DT V)
RF
CVBS IN
Side S-VHS
Analog
CVBS OUT
Side-CVBS
Comp2(DVD/ DTV)
TQFP 128KDDR MemoryTQFP 128KDDR Memory
Flash ROM512K/ 1MFlash ROM512K/ 1M
M62320FP(I2C Expender) M62320FP(I2C Expender)
CXA2069Q
UPD64083UPD64083
VPC3230 (MAIN)VPC3230 (MAIN)
VPC3230 (SUB)VPC3230 (SUB)DVD_SUB
DTV_Comp
M52758FPIC400(MUX)M52758FPIC400(MUX)
DVD_MAIN
DVD2_MAIN
DVD2_SUB
DTV2_Comp
S-VHS
Tuner (M)
Tuner (S)
VIN1
Y/ CIN1
Comp
Comp2
MNT_OUT
VIN2
Y/ CIN2
MAIN_VOUT
SUB_COUT
SUB_YOUT
CAB_VIN
MAIN_YOUT
MAIN_COUT
LA7151MSW CVBS/ Y
COMB_YOUT
COMB_COUT
ALT_Y_480I_MAIN
ALT_Y_480I_SUB
ALT_Y2_480I_MAIN
ALT_Y2_480I_SUB
S/ DVD_Comp
M37136(OTP)M37136(OTP)
CAB_Comb
MAIN_YOUT
M656 8 Bit
S656 8 Bit
Side A/ V
TMDS Transfer/ Thine
LVDS31PIN
RGB_24Bit
Analog RGB
DVI
VPORT(24bit )
SVPORT(16b it )
IEP
ZHINE
WIRE
Digta l BOARD
BOARD
- 31 -
MEMO
- 32 -
EXPLODED VIEW
300
305301
304
302
202
206
203
204
201
205
580
400
401
410
402
520
560
530
531
570
121
120
490
207
200
303
601
600
- 33 -
120 6401VD0013F SPEAKER ASSEM, BLYFULL RANGE(L) RZ-42PX10 SKD
121 6401VD0013E SPEAKER ASSEMBLY, FULL RANGE(R) RZ-42PX10 SKD
200 6348Q-E053W PDP, 42” 16:9 852*480 PDP42V60000.ADLGA
201 6871QCH034A PWB(PCB) ASSEMBLY, DISPLAY CTRL ASSY HAND INSERT 42V6 NEW MCM(1222) LVDS
202 6871QDH066A PWB(PCB) ASSEMBLY, DISPLAY YDRV ASSY HAND INSERT 42V6 YDRV TOP HAND INSERT ASSY
203 6871QDH067A PWB(PCB) ASSEMBLY, DISPLAY YDRV ASSY HAND INSERT 42V6 YDRV BTM HAND INSERT ASSY
204 6871QLH034A PWB(PCB) ASSEMBLY, DISPLAY XRLT ASSY HAND INSERT 42V6_XL(4LAYER)
205 6871QRH037A PWB(PCB) ASSEMBLY, DISPLAY XRRT ASSY HAND INSERT 42V6_XR(4LAYER)
206 6871QYH029A PWB(PCB) ASSEMBLY, DISPLAY YSUS ASSY HAND INSERT 42V6
207 6871QZH033A PWB(PCB) ASSEMBLY, DISPLAY ZSUS ASSY HAND INSERT 42V6
300 3091V00684D CABINET ASSEMBLY, RZ-42PX10, Silver
3091V00684L CABINET ASSEMBLY, RT-42PX11, 2 Tone Black
301 4980V01067B SUPPORTER, ASSY AL FILTER TOP RZ-42PX10 SKD
302 4980V01068B SUPPORTER, ASSY AL FILTER BOT.RZ-42PX10 SKD
303 4980V01069B SUPPORTER, ASSY AL FILTER RIGHT RZ-42PX10 SKD
304 4980V01070B SUPPORTER, ASSY AL FILTER LEFT RZ-42PX10 SKD
305 3790V00281F FILTER(MECH), GLASS FILTER MN42PZ44 1142G03EK 42KK NBK ETCHING MESH
400 3809V00444B BACK COVER ASSEMBLY, RZ-42PX10 SKD
401 3301V00025F PLATE ASSEMBLY, ASSY VSC TUNER COVER RZ-42PX10 SKD
402 3301V00023G PLATE ASSEMBLY, ASSY AV VSC TUNER RZ-42PX10 SKD
410 4980V01071B SUPPORTER, ASSY AL VERTICAL RZ-42PX10 SKD
490 4980V01057B SUPPORTER, PCB EGI POWER SW RZ-42PX10 SKD
520 6871VMMS15A PWB(PCB) ASSEMBLY,MAIN RF043B MALIBU RZ MAIN DIGITAL MANUAL
530 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU
531 5020V00915B BUTTON, POWER RZ-42PX10 ABS, AF-303S SKD
560 6871VSMS03A PWB(PCB) ASSEMBLY,SUB TUNER RF043B MALIBU RZ SUB ANALOG MANUAL
570 6871VSMZ91A PWB(PCB) ASSEMBLY,SUB CONT RF043A NEW HOLDER LOCAL KEY KODENSI
580 3501V00180A BOARD ASSEMBLY, POWER RZ-42PX10 RF043A 1H201W1 SANKEN PSU
600 6871VSME91A PWB(PCB) ASSEMBLY,SUB A/V RF043A MALIBU SIDE AV
601 4811V00118C BRACKET ASSEMBLY, SIDE AV RZ-42PX10 SKD
EXPLODED VIEW PARTS LIST
No. Part No. Description
AT24C02N-10 SI-2.7 R/TP 2K(256X8) 2-WIRE
M62320FP,I/O EXPANDER 16P SOP TP I/O
KA7809R, FAIRCHILD 2P D-PAK
MIC39100 SOT223 R/TP LDO TYPE 2.5V
PQ05DZ1U SMD TYPE R/TP REGULATOR
TK11840L 8P SOT23L CONVERTER PWM IC
PQ05DZ1U SHARP 5, SMD REGULATOR
AT24C02N-10SI-2.7 ATMEL 8P 2K(256X8) 2-WIRE
SN74HCT08D INSTRUMENT 16P QUADRUPLE
SN74LVTH541PWR 20P DRIVERS WTH 3 STATE OUTPUT
SN74LVTH541PWR DRIVERS WTH 3 STATE OUTPUT
THC63LVD103 TQFP TRAY 10BIT LVDS TX
SC1565IST-1.8 SOT223 TP REGULATOR
MIC391003P SOT223 LDO TYPE 2.5V REGULATOR
KA7809R, FAIRCHILD 2P REGULATOR IC
BA033FP-E2 TO252-3 R/TP 3.3V REGULATOR
PQ05DZ1U SMD TYPE R/TP REGULATOR
PQ05DZ1U SMD TYPE R/TP REGULATOR
BA033FP-E2 TO252-3 R/TP 3.3V REGULATOR
SC1565IST-1.8 SOT223 TP REGULATOR
BA033FP-E2 TO252-3 R/TP 3.3V REGULATOR
MIC39100 SOT223 R/TP LDO TYPE 2.5V REGULATOR
74ACT253SC 16P SOIC DUAL 4-INPUT MULTIPLEXER
ST3232CDR SOP16 R/TP RS232 DRIVER/RECEIVER
M52758FP MITSUBISHI 36PIN, R/TP PLL IC
DM74LS123MX 16SOP MONO. MULTIVIBRATOR
CXA2069Q QFP64 BK I2C BUS AV S/W
CXA2101AQ 80P,VIDEO SIGNAL PROCESSOR
SN74HCT08D NSTRUMENT 16P QUADRUPLE
LGDT4410 LG IC 176P QFP TRAY IEP
SDA6001 QH B12 128P MQFP TRAY MICOM
HY57V641620HGT-HT TRAY 64M SDRAM 133MHZ
MX29LV160ATTC-70 48P TSOP 16M FLASH MEMORY
AT24C16AN-10SI-2.7 SOIC R/TP EEPROM
KIA7027AF 3, SOT-89 TP RESET IC 2.7V
VPC3230D C5 80P TRAY VIDEO PROCESSOR PDP50
FLI2300BD 208P TRAY DIGITAL VIDEO CONVERTER
HY57V643220C(L)T-6 TRAY 64M FLASH MEMORY
VPC3230D C5 80P TRAY VIDEO PROCESSOR PDP50
GM1501HBD PBGA TRAY LCD/PDP CONTROLLER
AT24C32AN-10SI-2.7 8PIN SOP TP 32K 3.3V
KIA7042AF SOT-89 TP 4.2V DETECTOR
HY5DU283222AQ-5 100P LQFP TRAY 4MX32
MSP4410G-QA-C13-101WITH SRS WOW AND BBE
MX29LV800TTC-70 TSOP TRAY 8MBIT, 3.3V
NSP-6241B TRAY DIGITAL AUDIO PROCESSOR
TAS5122DCAR 56P/TSSOP 30W STEREO DIGITAL
SOCKET(CIRC),IC 822473-32.54MM PLCC
KIA7042AF SOT-89 TP 4.2V DETECTOR
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q001
Q002
Q100
Q1000
Q101
Q102
Q103
Q104
Q105
Q106
Q107
Q108
Q109
Q110
Q111
Q1200
Q1201
Q1202
Q207
Q208
Q209
Q210
Q211
Q214
Q300
Q301
Q302
Q303
Q304
Q305
Q306
Q307
Q308
Q309
Q310
Q311
Q312
Q313
Q314
Q315
Q316
Q400
Q400
Q401
Q401
Q402
Q402
Q403
Q404
Q405
Q406
0TR387500AA
0TR387500AA
0TR150400BA
0TRKE80038A
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR150400BA
0TR830009BA
0TR830009BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR104009AF
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
KTC3552T-RTK R/TP SOT-23F 50V 3A
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
BSS83 TP PHILIPS NON N-CHANNEL S/W
BSS83 TP PHILIPS NON N-CHANNEL S/W
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP KRC104S SOT-23
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
LOCA. NO PART NO DESCRIPTION
IC100
IC100
IC1000
IC1001
IC1002
IC1003
IC1004
IC101
IC102
IC103
IC104
IC1100
IC1200
IC1201
IC1202
IC1300
IC1301
IC1302
IC1303
IC1304
IC1305
IC1306
IC200
IC201
IC202
IC203
IC400
IC401
IC402
IC500
IC500
IC501
IC502
IC503
IC504
IC600
IC600
IC601
IC700
IC700
IC701
IC702
IC800
IC800
IC801
IC801
IC802
IC802
IC805
0IMMRAL014B
0IMI623200B
0IMCRFA010A
0IPRPML001A
0IMCRSH001A
0ITK118100B
0IMCRSH001A
0IMMRAL014B
0IMCRTI003A
0IMCRTI021A
0IMCRTI021A
0IMCRTH002A
0IMCRSJ001A
0IPRPML001A
0IMCRFA010A
0IMCRRH001A
0IMCRSH001A
0IMCRSH001A
0IMCRRH001A
0IMCRSJ001A
0IMCRRH001A
0IPRPML001A
0IFA742530B
0IMCRSG010A
0IMCRMI006A
0IFA741230A
0ISO206900A
0ISO210100B
0IMCRTI003A
0ICTMLG018A
0IMCRMN023A
0IMMRHY001F
0IMMRMR006B
0IMCRAL006A
0IKE702700D
0IIT323000E
0IMCRGN002C
0IMMRHY033A
0IIT323000E
0IPRPGN012A
0IMMRAL025A
0IKE704200J
0IMMRHY020B
0IMCRMN028A
0IMMRMR023A
0IMCRNL001A
0IMCRTI028C
6620VF3201A
0IKE704200J
IC TRANSISTOR
- 34 -
- 35 -
LOCA. NO PART NO DESCRIPTION
Q800
Q801
Q802
D100
D100
D1000
D1001
D1002
D1003
D1004
D101
D101
D102
D103
D104
D105
D116
D117
D118
D119
D120
D1200
D1201
D1206
D121
D122
D123
D124
D125
D126
D127
D128
D129
D130
D1300
D1301
D1302
D1303
D1304
D1305
D1306
D131
D200
D201
D202
D203
D204
D205
D500
D501
0TR387500AA
0TR387500AA
0TR387500AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
KDS184S CHIP 85V 300MA
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
KDS184S CHIP 85V 300MA
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
LOCA. NO PART NO DESCRIPTION
D502
D503
ZD100
ZD101
ZD206
ZD207
ZD208
ZD400
ZD401
ZD800
LD001
LD1000
LD1001
LD1002
LD1003
LD1203
LD1204
LD1206
LD1207
C002
C1001
C1002
C1003
C1004
C1006
C1016
C1017
C1018
C102
C1020
C1022
C1025
C1027
C1031
C1037
C104
C1041
C1042
C1045
C1046
C105
C1052
C1058
C1059
C106
C1060
C1061
C1063
C1066
C1066
0DD226239AA
0DD226239AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DZ820009AH
0DL200000CA
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0CE4763F618
0CE107SF6DC
0CE227VF6DC
0CE107SF6DC
0CE475SK6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE475SK6DC
0CE107SF6DC
0CE477SF6DC
0CE475SK6DC
0CE107SF6DC
0CE477SF6DC
0CE477SF6DC
0CE476DF618
0CE107SF6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476DF618
0CE107SF6DC
0CE107SF6DC
0CE477DJ618
0CE227VF6DC
0CE227VF6DC
0CE107SF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA
LEDSAM5670(DL-2LRG) BK Y-GREEN
LEDSAM2333 TP GREEN:10MCD, RED:6MCD
LEDSAM2333 TP GREEN:10MCD, RED:6MCD
LEDSAM2333 TP GREEN:10MCD, RED:6MCD
LEDSAM2333 TP GREEN:10MCD, RED:6MCD
LEDSAM2333 TP GREEN:10MCD, RED:6MCD
LEDSAM2333 TPGREEN:10MCD, RED:6MCD
LEDSAM2333 TPGREEN:10MCD, RED:6MCD
LEDSAM2333 TPGREEN:10MCD, RED:6MCD
47UF SRE 16V M FL TP5
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
4.7UF MVG 50V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
47UF STD 16V M FL TP5
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF STD 16V M FL TP5
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF STD 35V 20% FL TP 5
220UF MV 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP SMD
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
DIODE
CAPACITOR
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
- 36 -
LOCA. NO PART NO DESCRIPTION
C1067
C107
C1072
C1074
C1078
C1079
C108
C1081
C110
C111
C112
C113
C114
C120
C1202
C1205
C1206
C121
C121
C1211
C1212
C1215
C1216
C1218
C1220
C1229
C1233
C124
C1249
C1250
C1251
C1254
C1256
C1257
C1259
C127
C1273
C1274
C1275
C1279
C1305
C1314
C1315
C1317
C1331
C1333
C1353
C1355
C1362
C1366
C1368
C1373
0CE477DJ618
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
0CE107SF6DC
0CE227VF6DC
0CE475SK6DC
0CE477SF6DC
0CE106SF6DC
0CE475SK6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE477SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE227VF6DC
0CE477SF6DC
0CE227VF6DC
0CE227VF6DC
0CE477SF6DC
0CE107SF6DC
0CE227VF6DC
0CE227VF6DC
0CE477SF6DC
0CE227VF6DC
0CE227VF6DC
0CE227VF6DC
0CE227VF6DC
0CE475SK6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE227VF6DC
0CE227VF6DC
0CE107SF6DC
470UF STD 35V 20% FL TP 5
470UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP SMD
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
4.7UF MVG 50V 20% SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
4.7UF MVG 50V 20% SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP SMD
220UF MV 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
LOCA. NO PART NO DESCRIPTION
C1374
C1384
C1388
C1391
C1400
C1402
C1404
C1410
C1415
C1425
C208
C220
C222
C222
C223
C223
C224
C224
C224
C225
C226
C227
C230
C251
C254
C258
C261
C263
C272
C274
C301
C302
C304
C316
C317
C318
C323
C325
C327
C400
C401
C402
C404
C406
C410
C423
C429
C435
C440
C442
C502
C505
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE477SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476XFKDC
0CE476SF6DC
0CE476XFKDC
0CE476SF6DC
0CE476XFKDC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CN105EJ56A
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
0CE227VF6DC
0CE476SF6DC
0CE107SF6DC
0CE105SK6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP SMD
470UF MVG 16V 20% R/TP SMD
47UF MVG 16V M SMD R/TP
47UF MVK-BP,CN 16V 20%,-20% SMD TAPPING
47UF MVG 16V M SMD R/TP
47UF MVK-BP,CN 16V 20%,-20% SMD TAPPING
47UF MVG 16V M SMD R/TP
47UF MVK-BP,CN 16V 20%,-20% SMD TAPPING
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
1.0UF 3216 35V 10% R/TP X7R
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP SMD
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP SMD
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
1UF MVG 50V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
- 37 -
LOCA. NO PART NO DESCRIPTION
C506
C507
C508
C509
C517
C520
C522
C523
C525
C527
C529
C534
C604
C612
C615
C627
C629
C632
C702
C703
C709
C712
C720
C723
C726
C737
C744
C752
C757
C762
C769
C777
C778
C785
C800
C801
C802
C803
C812
C817
C822
C825
C827
C828
C829
C834
C834
C837
C840
C841
C847
C851
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE105SK6DC
0CE106SF6DC
0CE476SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CE107SF6DC
0CE107SF6DC
0CE226SF6DC
0CE106SF6DC
0CE106SF6DC
0CE226SF6DC
0CE226SF6DC
0CE106SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE335SK6DC
0CE226SF6DC
0CE226SF6DC
0CE476SF6DC
0CE226VF6DC
0CE226VF6DC
0CE226SF6DC
0CE107SF6DC
0CE335SK6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CN105EJ56A
0CE108DH618
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
1UF MVG 50V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
47UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
22UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP SMD
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
3.3UF MVG 50V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
47UF MVG 16V M SMD R/TP
22UF MV 16V 20% R/TP SMD
22UF MV 16V 20% R/TP SMD
22UF MVG 16V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
3.3UF MVG 50V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
10UF MVG 16V 20% R/TP SMD
100UF MVG 16V M SMD R/TP
1.0UF 3216 35V 10% R/TP X7R
1000UF STD 25V M FL TP5
LOCA. NO PART NO DESCRIPTION
C852
C862
C863
C872
C873
C874
L1004
L1005
L1006
L1007
L1200
L1203
L1209
L1213
L803
L804
L805
L806
AR1101
AR1102
AR1103
AR1104
AR1105
AR1106
AR500
AR503
AR507
AR508
AR509
AR512
AR513
AR520
AR521
AR522
AR523
AR524
AR525
AR600
AR600
AR601
AR601
AR602
AR602
AR603
AR603
AR604
AR605
AR606
0CE108DH618
0CF4741L438
0CF4741L438
0CE335SK6DC
0CN105EJ56A
0CE108DH618
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0022A
6140VB0022A
6140VB0022A
6140VB0022A
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
1000UF STD 25V M FL TP5
0.47UF D 63V 5% TP 5 M/PE NI
0.47UF D 63V 5% TP 5 M/PE NI
3.3UF MVG 50V 20% SMD R/TP
1.0UF 3216 35V 10% R/TP X7R
1000UF STD 25V M FL TP5
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKE26UH 22.5TURN YL-9N 0.4
COIL,CHOKECPS-0810 GET 22UH 21.5TURNS
COIL,CHOKECPS-0810 GET 22UH 21.5TURNS
COIL,CHOKECPS-0810 GET 22UH 21.5TURNS
COIL,CHOKECPS-0810 GET 22UH 21.5TURNS
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
COIL
RESISTOR
- 38 -
LOCA. NO PART NO DESCRIPTION
AR607
AR608
AR609
AR610
AR611
AR612
AR613
AR614
AR615
AR616
AR617
AR618
AR700
AR701
AR701
AR702
AR703
AR707
AR708
AR709
AR710
AR711
AR712
AR713
AR714
AR715
AR717
AR718
AR719
R801
R802
SW001
SW002
SW003
SW004
SW005
SW006
SW700
SW800
SW800
L100
L100
L1000
L1001
L1002
L1008
L1009
L101
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RKZVTA001L
0RKZVTA001L
140-315A
140-315A
140-315A
140-315A
140-315A
140-315A
140-313B
6600VM2006A
140-275A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
1.0M OHM 1/2 W 5% TA52 UL PILKOR
1.0M OHM 1/2 W 5% TA52 UL PILKOR
TACT, SKHV17910B LG C&D NON 12V
TACT, SKHV17910B LG C&D NON 12V
TACT, SKHV17910B LG C&D NON 12V
TACT, SKHV17910B LG C&D NON 12V
TACT, SKHV17910B LG C&D NON 12V
TACT, SKHV17910B LG C&D NON 12V
TACT, 2LEAD 160G(TA) LG C&D NON
PUSH, SDDF3PATP011 250V 4A HORIZONTAL
PUSH, JDPB21SA 30V 0.3A HORIZONTAL 500G
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
LOCA. NO PART NO DESCRIPTION
L101
L1010
L1011
L1012
L1013
L1014
L1015
L1016
L1017
L1018
L1019
L102
L102
L103
L103
L104
L105
L105
L106
L107
L108
L1206
L1207
L1210
L1211
L1216
L1217
L1300
L1302
L1307
L1310
L1311
L1312
L1313
L1314
L1315
L1316
L1317
L1318
L1321
L1322
L1325
L1326
L1327
L1328
L1329
L1330
L1331
L1332
L1333
L200
L200
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8010L
6200JB8010L
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8013L
6210VC0006A
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
BEAD FEELUX 60 OHM TB201209U060
FBMH3216 HM501NT3.2X1.6X1.6MM
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
SWITCH
FILTER & CRYSTAL
- 39 -
LOCA. NO PART NO DESCRIPTION
L201
L202
L203
L204
L205
L206
L208
L210
L211
L212
L213
L213
L214
L215
L216
L216
L300
L301
L302
L305
L306
L307
L308
L309
L310
L311
L312
L313
L314
L400
L400
L401
L401
L402
L403
L404
L405
L406
L407
L500
L501
L502
L503
L504
L505
L506
L507
L700
L800
L807
L808
R102
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6210VC0006A
6200JB8010L
6200JB8010L
6200JB8010L
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0005A
6210VC0005A
6210VC0005A
6210VC0006A
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0005A
6210VC0005A
6210VC0005A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8010L
6200JB8010L
6200JB8010L
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
FBMH3216 HM501NT3.2X1.6X1.6MM
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
BK2125 HS 7502X1.25X0.85MM
BK2125 HS 7502X1.25X0.85MM
BK2125 HS 7502X1.25X0.85MM
FBMH3216 HM501NT3.2X1.6X1.6MM
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
BK2125 HS 7502X1.25X0.85MM
BK2125 HS 7502X1.25X0.85MM
BK2125 HS 7502X1.25X0.85MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
FBMH3216 HM501NT3.2X1.6X1.6MM
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
LOCA. NO PART NO DESCRIPTION
R103
R106
R107
R108
X500
X600
X600
X700
X700
X800
JK103
JK200
JK201
JK202
JK300
P101
P102
P201
A1
A2
A3
A4
A5
A6
A7
A8
F801
F801A
F802A
P100
P200
PA001
TU100
TU101
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6202VDT002K
6202VDT002J
6202VDB007B
6202VDT002B
6202VDB007B
156-A02M
6613V00026A
6612M00009A
6612M00009A
6612M00009A
6612J00057A
380-068E
6612BBBHN6A
380-068E
3828VA0468F
6710V00126R
6410VEH003C
6850J00003A
6850J00004A
6850VA0004E
6851V00022C
6866VA9001B
0FS1002B53K
430-813A
430-813A
6630VGA001C
6630VGA004B
6712000002A
6700MF0010A
6700MF0010B
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
MLB-201209-1000L-N2 1000OHM 350MA
CRYSTAL, SX-1 6MHZ 16PF TP .
CRYSTAL, SX-1 13.500000MHZ 14PF
CRYSTAL, HC49U 250MHZ 30PPM 13PF
CRYSTAL, SX-1 SC14.3MHZ +/- 30 PPM 16PF
CRYSTAL, HC49U 20.250MHZ 30PPM 13PF
CRYSTAL, HC49U 432MHZ 30PPM 10PF BK
ASSEMBLY, UJB-03-28A UGCOM
SCART, UJB-R1-033 UGCOM 21P
SCART, UJB-R1-033 UGCOM 21P
SCART, UJB-R1-033 UGCOM 21P
RCA, UJB-08-01A UGCOM 8P RCA+1P S-JACK
PHONE, UEJ-CV-018 UGCOM D3.5 E/P
DIN, 440062-1 AMP DVI CED RIGHT ANGLE
PHONE, UEJ-CV-018 UGCOM D3.5 E/P
MANUAL,OWNERS RF043B PX10/2 LG
REMOTE CONTROLLER, PIP RZ-42PY20 40
POWER CORD, M2511A-001 2800MM
CABLE, DVIDVI-D TO DVI-D
CABLE, DVILVDS UL20276 AWG30 500MM
CABLE, COAXIAL COAXIAL CALBE(PAL)
CABLE, COAXIAL COAXIAL(150MM)
CONNECTOR (CIRC), D-SUB 2990-9C
FUSE, SLOW BLOW10000MA 250 V 5.2X20
HOLDER, FUSE NON MC994C PAPING
HOLDER, FUSE NON MC994C PAPING
CONNECTOR (CIRC), D-SUB 68114-1521
CONNECTOR (CIRC), D-SUB 69107-0921
REMOTE CONTROLLER RECEIVER
TUNER, TAUM-W501P 4SYSTEM MAIN
TUNER, TAFM-W502P 4SYSTEM SUB
JACK
ACCESSORIES
MISCELLANEOUS
PRINTED CIRCUIT BOARD
MAIN (TOP) POWER S/W(TOP)
SIDE A/V(TOP) SIDE A/V(BOTTOM)
CONTROL(TOP)
CONTROL(BOTTOM)
POWER S/W(BOTTOM)MAIN (BOTTOM )
TUNER(TOP) TUNER(BOTTOM)
March, 2004Printed in KoreaP/NO : 3828VD0161D