Lg 42px4r Za

PLASMA TVSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : MF-056A

MODEL : 42PX4R42PX4R-ZA

website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html

PRVOLMENUTV/AV OK

- 2 -

CONTENTS

SAFETY PRECAUTIONS ....................................................................................3

DESCRIPTION OF CONTROLS ..........................................................................4

SPECIFICATIONS................................................................................................8

ADJUSTMENT INSTRUCTIONS .......................................................................10

TROUBLE SHOOTING GUIDE..........................................................................14

BLOCK DIAGRAM.............................................................................................23

EXPLODED VIEW..............................................................................................24

EXPLODED VIEW PARTS LIST ........................................................................25

REPLACEMENT PARTS LIST...........................................................................26

SCHEMATIC DIAGRAM.........................................................................................

PRINTED CIRCUIT BOARD ..................................................................................

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.

It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.

When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

Remote Control Key Functions- When using the remote control aim it at the remote control sensor of the set.- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.

MODE

TV/AV

TV

DVDVCR

PIP

ZOOM - ZOOM +MUTE

TEXT/ *

SLEEP LIST

I/II

AUDIO

PIP PR -PIP PR + SWAP

PIPINP

UT

STB

MENU

ARC

SSM

FAVOURITE

SIZE POSITION INDEX HOLD

TIME REVEAL MIX MODE

Q.VIEW

PSM

OK

VOL PR

MULTIMEDIA

POWER

CABLE

M?

EXIT

MULTIMEDIASelects the Component, RGB or HDMImodes.switches the set on from standby.

PIPSwitches the sub picture on or off.

Selects PIP or DW modes.PIP PR + /-

Selects a programme for the sub picture.SWAP

Alternates between main and sub picture.PIP INPUT

Selects the input mode for the sub picture.SIZE

Adjusts the sub picture size.POSITION

Moves the sub picture to DD / EE or FF / GGdirection.

POWERswitches the set on from standby or off tostandby.

ARC Changes the picture format.

OKaccepts your selection or displays the cur-rent mode.

DD / EE or FF / GGAdjusts menu settings.Selects menu item.

MENUDisplays on screen menus one by one.

Exits the current menu.Memorizes menu changes.

ZOOM - / ZOOM +Enlarges or reduces the main picture size.

TEXT/*These buttons are used for teletext.For further details, see the ‘Teletext’ section.

Note : In teletext mode, the PIP PR +/-,SWAP and PIP INPUT buttons are used for

teletext function.

SSMTo select the sound appropriate to your

viewing programme character.

NUMBER buttons

SLEEPSets the sleep timer. I/II

Selects the language during dual lan-guage broadcast.Selects the sound output.

LISTDisplays the programme table.

TV/AVSelects the TV, AV, Component, RGB or

HDMI modes.switches the set on from standby.

MODESelects another device.

MUTESwitches the sound on or off.

VOL +/- (Volume Up/Down)Increases/decreases sound level.PR +/- (Programme Up/Down)Selects a programme.

PSMAdjusts the factory preset picture accord-ing to the room.

Q.VIEWReturns to the previously viewed pro-gramme.

FAVOURITEselects a favorite programme.

EXITClears all on-screen displays and returnsto TV viewing from any menu.

VCR BUTTONSControls a LG video cassette recorder.

- 4 -

DESCRIPTION OF CONTROLS

- 5 -

Location and Function of Controls

<Front Panel Controls>

PRVOLMENUTV/AV OK

PRVOLMENUTV/AV OK

2 1 3 4 5 6

7

8

1. Power ButtonSwitches the set on from standby or off to standby.

2. Remote Control Sensor

3. TV/AV ButtonSelects the TV, AV, Component, RGB or HDMI modes. Switches the set on from standby.

4. MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.

5. OKAccepts your selection or displays the current mode.

6. DD / EE (Programme Up/Down)Selects a programme or a menu item.Switches the set on from standby.FF / GG (Volume Up/Down)Adjusts the volume.Adjusts menu settings.

7. Power IndicatorIlluminates red in standby mode, Illuminates green when theset is turned on

8. Intelligent EyeAdjusts picture according to the surrounding conditions.

- 6 -

Location and Function of Controls

<Back Panel>

S-VIDEO

VID

EO

AU

DIO

RL/

MO

NO

AAV5V5

AC INPUT

Antenna

AUDIO AUDIO

L R

VIDEO VIDEO

COMPONENTCOMPONENT AUDIO AUDIO

L R

V VARIABLE ARIABLE AUDIO OUTAUDIO OUT

AUDIO AUDIO

(MONO)(MONO)L R

S-VIDEOS-VIDEO VIDEOVIDEO

AAV4V4

AAV1V1

AAV2V2

AAV3V3

HDMI/DVI(VIDEO) AUDIO INPUT RGB INPUT

RS-232C INPUT(CONTROL/SERVICE)

REMOTECONTROL

1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER, DVD or STB to this socket.Note: If you want to use RGB/DVI audio, we strongly recom-mend that you use the cable that has a core, or the EMI Filtercore along with separate cable.

2. CONTROL LOCK / REMOTE CONTROL

3. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.

4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.

AUDIO/VIDEO IN SOCKETS (AV4)Connect the audio/video out sockets of external equipment tothese sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in AV4.

5. VARIABLE AUDIO OUTPUT

6. EURO SCART SOCKETConnect the euro scart socket of the VCR to these sockets.Note: If you want to use the EURO scart cable, you have touse the signal shielded Euro scart cable.

7. ANTENNA INPUT

8. POWER CORD SOCKETThis set operates on an AC power. The voltage is indicated onthe Specifications page. Never attempt to operate the set onDC power.

9. AUDIO/VIDEO INPUT (AV5)S-VIDEO/AUDIO IN SOCKETS

1 42 3 6 75 8

9

- Shown is a simplified representation of the set.- Here shown may be somewhat different from your set.- This manual explains the features available on the 42PX4RV series / RT-42PX40 series.

- 7 -

AS mark

LG TV

Owner’s Manual

1.5V1.5V

Alkaline batteries Power Cord

MODE

TV/AV

TV

DVDVCR

PIP

ZOOM - ZOOM +MUTE

TEXT/ *

SLEEP LIST

I/II

AUDIO

PIP PR -PIP PR + SWAP

PIPINP

UT

STB

MENU

ARC

SSM

FAVOURITE

SIZE POSITION INDEX HOLD

TIME REVEAL MIX MODE

Q.VIEW

PSM

OK

VOL PR

MULTIMEDIA

POWER

CABLE

M?

EXIT

Remote Control handset

- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.

- Contract your dealer for buying these items.

Optional Extras

Accessories

Tilt wall mounting bracket Video cables Audio cablesCeiling mounting bracket

40

4250

42

40

- Secure the set assembly by joinning it to a wall by using the Eye Bolts/Wall brackets.

Joinning the set assembly to the wall to protect the set tumbling

• After the set must be mounted on a desktop, install the Eye Bolts on the set asshown.Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 2 bolts, (not supplied with the product),as shown.Match the height of the Eye Bolts and the wall brackets. Check to be sure the brackets are tightened securely.

• Secure the set assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.

2-Wall brackets

2-Eye Bolts

SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.

- 8 -

V Application RangeThis spec is applied to the 42”PDP TV used MF-056A Chassis.

V Specification

Each part is tested as below without special appointment.1) Temperature : 25±5°C (77±9°F), CST : 40±52) Relative Humidity: 65±10%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)

* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification

Safety: CE, IEC specificationEMC : CE, IEC

V General Specification

1. General Specification

Remark

Safety : IEC/EN60065, EMI : EN55013, EMS : EN55020

Model Name

42PX4R-ZA

Market

EU

Remark

PDP

Glass/Film type is TBD

LGE SPEC

Maker : SONY/ Sanken

Specification

42 inch wide Color Display Module

16:9

PDP42X2##2#,

RGB Closed Type, Glass Filter

1) Temp : 0~40 deg

2) Humidity : 0~85%

1) Temp : -20~60 deg

2) Humidity : 0~85%

100-240V~, 50/60Hz

No

1

2

3

4

5

6

Item

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

2. Model Specification

- 9 -

Item

Market

Broadcasting system

Available Channel

Receiving system

Scart Jack(3EA)

Video input(2EA)

S-Video Input(3EA)

Component Input(1EA)

RGB Input(1EA)

HDMI Input(1EA)

Audio Input(4EA)

Wired Control

Audio variable out(1EA)

No

1

2

3

4

5

6

7

8

9

10

11

12

13

Specification

EU

PAL B/G/I/D/K, NTSC

BAND PAL NTCS

VHF/ UHF C1~C69 2~83

CATV S1~S47 1~71

Upper Heterodyne

PAL, SECAM, NTSC

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

RGB-DTV

HDMI-PC

HDMI-DTV

PC Audio, Component(1EA), AV(2EA)

Remark

4 System : PAL, SECAM, NTSC,PAL60

4 System : PAL, SECAM, NTSC,PAL60

L/R Input

- 10 -

ADJUSTMENT INSTRUCTIONS

1. Application ObjectThese instructions apply to the MF-056A Chassis.

2. Specification(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolationtransformer will help protect test instrument.

(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.

(4) The input voltage of the receiver must keep 100-220V,50/60Hz.

(5) The receiver must be operated for about 15 minutes priorto the adjustment.

O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.

O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE

PATTERN.

[ Set is activated HEAT-RUN without signal generator inthis mode.

[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.

Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), afterimage may be occur in the black level part of thescreen.

3. Channel memory

3-1. Setting up the LGIDS1) Install the LGIDS. (idsinst.exe)2) After installation, restart your PC.3) Extract [files.zip] to folder [c:\LGIDS\files].4) Start LGIDS.

3-2. Channel memory Method 1) Select “PDP” and “Hurricane” on Model dialog. And check

your connection in Communication dialog. (If yourconnection is ‘NG’, then set your PORT(COM1,2,3,...)correctly.)

2) Connect RS-232C cable and turn on the power.(If your connection has completed, you can see “Ready”.)

[ If your set is not an end products but only a board, youhave to make your board to Stand-by state (LED_R). Andyou have to Download in Stand_by power state.

3) Select proper CH_memory file(*.nvm) for each model at[NVRAM Download] $ [Write Batch]Next, select proper binary file(*.bin) including the CHinformation for each model at [NVRAM File].

4) Click the [Download] button.It means the completion of the CH memory download if allitems show ‘OK’ and Status is changed by ‘PASS’ at thelower right corner of the window.

5) If you want to check whether the CH information ismemorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CHinformation downloaded.

3-3 Sub program download

1) Select “PDP” and “Hurricane” on Model dialog. And checkyour connection in Communication dialog. (If yourconnection is ‘NG’, then set your PORT(COM1,2,3,...)correctly.)(Fig. 1)

(Fig. 3)

(Fig. 3-1)

- 11 -

2) Connect RS-232C cable and turn on the power. (Use thespecial Cable For Sub-program) (If your connection hascompleted, you can see “Ready”)

4. POWER PCB Assy V oltage Adjustments (Va, Vs Voltage Adjustments)

4-1. Test Equipment : D.M.M. 1EA

4-2. Adjustment Method[P/No 3501V00220A(Sanken PSU) B/D]

(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P807, connect

- terminal to GND pin of P807.3) After turning RV501, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)

(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P807, connect

– terminal to GND pin of P805.2) After turning RV401, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)

5. EDID (The Extended DisplayIdentification Data)/ DDC (DisplayData Channel) download

5-1. Required T est Equipment1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID

TESTER Ver.2.5)2) A Jig for EDID Download3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable

5-2. Setting of device

5.3. Preparation for Adjustment1) As above Fig. 5, Connect the Set, EDID Download Jig, PC

& Cable.2) Turn on the PC & EDID Download Jig. And Execute the

S/W : EDID TESTER Ver,2.53) Set up S/W option

Repeat Number : 5Device Address : A0PageByte : 8

4) Power on the Set

5.4. Sequence of Adjustment

(1) DDC data of Analog-RGB1) Init the data

2) Load the EDID data.(Open File)[Analog-RGB : MF056A_RGB.ANA][digital(HDMI) : MF056A_DMI.DVI]

3) Set the S/W as below.4) Push the “Write Data & Verify”button. And confirm “Yes”.5) If the writing is finished, you will see the “OK” message.

Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)

(Fig. 4) Connection diagram of power adjustment for measuring

(Fig. 5) Connection Diagram of DDC download

- 12 -

6. Auto A V(CVBS) Color Balance

6-1. Required- This AV color balance adjustment should be performed beforwhite Balance Adjustment

6-2. Required Equipment1) Remote controller for adjustment2) AV Pattern Generator

: 802F Pattern Generator, Master(MSPG-925FA), etc(Which has PAL Composite Video format output withstandard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)

6-3. Method of Auto Color Balance1) Input the PAL Composite Video (Fig6. 100% Color Bar

Pattern) into video input.(42PX4RV-TA : AV1/AV2 Input 50Hz,42PX4RV-ZA : AV4/AV5 Input)

2) Set the PSM to Standard mode in Picture menu.3) Press INSTAR key on R/C for adjustment.4) Press the G (Vol. +) key operate to set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

7. Adjustment of White Balance

7-1. Required Equipment1) Remote controller for adjustment2) Color Analyzer (CA-100 or same product)3) Auto W/B adjustment instrument(only for auto adjustment)4) AV Pattern Generator

7-2. Connecting diagram of equipment formeasuring (For Auto Adjustment)

W Auto adjustment Map(RS-232C)

7-3. Adjustment of White Balance

O Operate the zero-calibration of the CA-100, then sticksensor to PDP module surface when you adjust.

O For manual adjustment, it is also possible by the followingsequence.

1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operate heatrun more than 15 minutes.

2) As below Fig.7-1, Supply 216Level (85 IRE) full screenpattern to Video input.(42PX4RV-TA : AV1/AV2 INPUT 50Hz,42PX4RV-ZA : AV4/AV5 INPUT)

3) Press the TV/AV KEY on R/C for converting input mode.4) Set the PSM to Standard mode in Picture menu.5) Enter the White Balance adjustment mode by pressing the

INSTART key twice(White Balance) on R/C.6) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and offset) using D / E (CH +/-) keyon R/C.

7) Adjust Only High Light with R Gain/ B Gain using F / G(VOL+/-) key on R/C.

8) Adjust it until color coordination becomes as below.(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset7E, B Offset 80 is Fixed)[MF-056A : 42PX4RV-TA/ZA] - VGA 42”Bright : High Light : 80 ± 20cdColor-Coordinate : High Light : X : 0.285 ± 0.003

Y : 0.295 ± 0.003Color Temperature : 9,300°K ± 500°K

9) When adjustment is completed, Exit adjustment modeusing EXIT key on R/C

(Fig. 7-1) Pattern for Adjustment of White Balance

Win

CV BS si gnal i npu

COL OR

A NA L YZER

T YPE; CA-100

PDP MONIT OR

High Light adjust

L ow L ight adj ust

Type

Baud Rate

115200

Index

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Data bit

8

Cmd1 Cmd2

j a

j b

j c

j d

j e

j f

Stop bit

1

Parity

NONE

MF-056A : RT-42PX40/ RZ-42PX40

ProtocolSetting

Data Min Value

00(00)

00(00)

00(00)

00(00)

00(00)

00(00)

Max Value

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern

(Fig. 7) Connection Diagram of Auto W/B adjustment

- 13 -

8. Auto Component Color Balance

8-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator

(Which has 720p Ypbpr output & PC 1024x768 60Hz withStandard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.8)

8-2. Method of Auto Component Color Balance1) Input the Component 720p 100% Color Bar signal into

Component1 or Component2.2) Set the PSM to Standard mode in Picture menu.3) Press INSTART key on R/C for adjustment.4) Press the G (Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means complete adjustment

9. Auto RGB Color Balance

9-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator, Master (MSPG-925FA), etc.

(Which has XGA 60Hz PC Format output with standard(0.7Vpp) horizontal black and white pattern as Fig.10)

9-2. Method of Auto RGB Color Balance1) Input the PC 1024x768 60Hz horizontal black and white

pattern into RGB.2) Set the PSM to Standard mode in Picture menu.3) Press ADJ key on R/C for adjustment.4) Press the G (Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

9. Default V alue in Adjustment mode

9-1. Auto Color Balance (Component/RGB)

9-2. White Balance

Level : 0

Level : 255

(Fig. 9) Auto RGB Color Balance Test Pattern

(Fig. 10) Default Value on OSD

(Fig. 10-1) Default Value on OSD

Auto Color Balance(HEX)

Auto-RGB G To SetRed Offset1 80Green Offset1 80Blue Offset1 80Red Offset2 80Green Offset2 80Blue Offset2 80Red Gain 80Green Gain 80Blue Gain 80Reset G To Set

White Balance(Hex)

Red Gain 80Red Offset 80Green Gain 80Green Offset 80Blue Gain 80Blue Offset 80Reset G To Set

(Fig. 8) Auto Component Color Balance Test Pattern

- 14 -

TROUBLE SHOOTING GUIDE

1. Power Board

1-1. The whole flowchart which it follows in voltage output state

Start check

Manufacture enterprisemeaning of a passage

1. Check the Power Offcondition.

Doesn't the screen whole come

out?

Is it identical with Power Off

condition?

Yes

Yes

No

No

No

No

No

2. Check the Interfacesignal condition.

Is the Interface signal operated?

Yes

3. Check the St-by 5Vsignal circuit.

Doesn't the low pressure output

come out?

Doesn't the St-by 5V signal

come out?

Yes

Yes

No

4. Check the 5V Monitorsignal circuit.

Doesn't the 5V Monitor signal

come out?

Yes

7. Check the VSC Vs-ONsignal

Doesn't the high tension output

come out?

Doesn't the VSC signal Vs-ON

come out?

Yes

Yes

Doeshigh tension

output voltage Dropoccur?

When theY B/D Module

input connector isremoved, does output

voltage dropoccur?

When theY, Z B/D Module

input connector is remove,does Power Board hightension

output voltage Dropoccur?

Yes No No

9. Check the PowerBoard Output high

tension circuit

Yes

10. Check the Z B/DModule output circuit

Yes

When theZ B/D Module

input connector isremoved, does output

voltage Drop occurs?

11. Check the Y B/DModule output circuit

Yes

No

8. Check the Vs, Vavoltage output circuit.

Doesn't the Vs, Va voltage output

come out?

Yes

No

No

5. Check the VSC RL-ONsignal.

Doesn't the VSC signal RL-ON

come out?

Yes

6. Check the VSC lowpressure output

Doesn't the VSC low pressureoutput come out?

Yes

- 15 -

1-2. Sony Power Board Structure

1 2 3

T502: Vs Trans

T702: Va Trans

T101: St-by Trans

T103: Low Voltage Trans

- 16 -

1-3. Sanken, LGIT Power Board Structure

1 2 3

T221: Vs Trans

T271: Va Trans

T121: St-by Trans

T201: Low Voltage Trans

- 17 -

2. No Power

(1) Symptomfl Does’t minute discharge at module. fl Non does not come in into the front LED.

(2) Check following

Is plug in power cord? Plug in power cord.

Yes

No

Is the Line Filter and PowerBoard Cable connected?

Connect the Cable.

Yes

No

Is the Fuse(F101) onPower Board normal?

Replace the Fuse.

Yes

No

Is the Power Board and 7P ofVSC Board Cable connected?

Connect the Cable.

Yes

No

After the cable connect is remvedto Power Board(except the CN101connection cable), the AC voltagemarking is authorized on manual.When ST-BY 5V is not operated,replace Power Board.

- 18 -

3. Protect Mode

(1) Symptomfl After once shining, it does not discharge minutely

from modulefl The Rely falls(The sound is audible “click”) fl It is converted with the color where the front LED

is red from green.

(2) Check following

Is the Power Boardnormal ?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replace theconnector.

ReplaceY-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Boardnormal?

ReplaceX-Board.

Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of

Ctrl-B/D?

Yes

No Yes

Is the Y-Boardnormal?

Is the output voltagenormal after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)

Yes

No Yes Yes

ReplaceZ-Board.

Is the Z-Boardnormal?

Is the output voltagenormal after removeP1 connector of Z-

B/D?

Is the Fuse (FS1, FS2) on Z-B/Dnormal? (In case of open is replace)

Yes

No Yes

Is the X- Boardnormal?


X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D

Yes

No Yes

Is the VSC Board normal?

Is the output voltage normal afterremove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, 1100 normaloperation: Replace VSC Board

Yes

No

Is the COF of X, Y, Znormal ?

No

Yes

Yes

- 19 -

4. No Raster

(1) Symptomfl Does’t minute discharge at module. fl It maintains the condition where the front LED is green.

(2) Check following

Is the Power Boardnormal?

Replace thePower Board.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replace theconnector.

ReplaceY-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Board normal?

ReplaceX-Board.


Ctrl-B/D?

Yes

No Yes

Is the Y-Boardnormal?

Is the output voltagenormal after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) normal on Y-B/D?(In case of open is replace)

Yes

No Yes Yes

ReplaceZ-Board.

Is the Z- Board normal?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is the Fuse(FS1, FS2) normal onZ-B/D? (In case of open is replace)

Yes

No Yes

Is the X- Board normal?


X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace the Left X-B/D

Yes

No Yes

Is the VSC Board normal?

Is the output voltage normal afterremove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, P1100 normaloperation: Replace the VSC Board

Yes

No

Is the COF of X, Y, Znormal?

No

Yes

Yes

- 20 -

5. In case of occurring strange screen into specific mode

5-1. In case the OSD does not displayed

(1) Symptomfl LED is greenfl The minute discharged continuously becomes accomplished from module

(2) Check following

Is the LVDS cablenormal ?

Is the VSC Boardnormal?

Is the LVDS cableconnected well?

Cable inserts well.Yes

No

No

Yes

Does the FIL8532 IC(IC800) Operates ?

Replace FIL8532IC(IC800).

No

Is the Ctrl Board ofModule normal?

Replace Ctrl B/D.No

No

YesReplace VSC B/D

Replace the cable.Yes

- 21 -

5-2. In case of does’t display the screen into specific mode

(1) Symptomfl The screen does not become the display from specific input mode

(RF, AV, Component, RGB, DVI).

(2) Check followingfl Check the all input mode should become normality display.fl Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become

normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode

(4) In the case of becomes unusual display from RF, AV mode

(5) In the case of becomes unusual display from Component, RGB mode

(6) In the case of becomes unusual display from HDMI mode

Is the Tuner normal?

Is the CXA2069Qnormal?

Is the Tuner Cableconnected well?

Cable inserts well.Yes

No

No

Yes

Is the FIL8532normal?

Replace the Tuner

No

Is the Input voltage, IIC Communicationand CVBS output normal?

Yes

Is the Input voltage, IICCommunication and HV sync

normal?

NoReplace the IC

No

Is normal the Input voltage, IICCommunication and HV sync?

NoReplace the IC

No

Is the CXA2069Qnormal?

Yes



normal?

NoReplace the IC

No


normal?

NoReplace the IC

No



normal?

NoReplace the IC

No

Is the Sil9011normal?

Yes



normal?

NoReplace the IC

No


normal?

NoReplace the IC

No

- 22 -

6. In case of no sound

(1) Symptomfl LED is greenfl Screen display but sound is not output

(2) Check following

Is the SPK cablenormal?

Is the SPK cableconnected well?

Cable inserts well.

No

No

Replace IC400

No

Replace IC401

No

Replace SPK cableYes

Yes

Is the RF/ AV/Component/ RGB/

HDMI sound normal?

No Does IC400Operates ?

Does IC401Operates ?

Replace IC402

No

Does IC402Operates ?

Replace VSC B/D

Yes Yes

- 23 -

BLOCK DIAGRAMca

ble

’

- 24 -

EXPLODED VIEW

301

304

303

302

207

201

580

410

400

430

501

401

520

200

202

203

204

205

206

121

601600

120

531

530

700

300

305

570

101

103

300

- 25 -

101 5900V06008B FAN,DC G6015S12B2-RG DONGYANG 60*60*15 7V 1900RPM 6/12V L=500MM

103 4980V00D43B SUPPORTER, FAN SECC(EGI) MZ-42PM10 PRESS

120 6401VD0024A SPEAKER ASSEMBLY, FULL RANGE(R) NON RZ-42PX40 R

121 6401VD0025A SPEAKER ASSEMBLY, FULL RANGE(L) NON RZ-42PX40 L

200 6348Q-E101N PDP, 42” 1024*768 PDP42X20422.ADLGB

201 6871QCH060B PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42X2AI

202 6871QDH090B PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42”HD 42X2A TOP

203 6871QDH091B PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42”HD 42X2A BTM

204 6871QLH037A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42X2 X-LEFT(TCP)

205 6871QRH043A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42X2 X-RIGHT (TCP)

206 6871QYH042B PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42”HD 42X2A

207 6871QZH047B PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42”HD 4X2A

300 3091V00739N CABINET ASSEMBLY, 42PX4R-ZA STEREO E_PHONE LGEFS (SKD)

301 4980V01128C SUPPORTER, ASSY AL 42PX4D-UB 0.8T TOP C/SKD

302 4980V01130C SUPPORTER, ASSY AL 42PX4D-UB 0.8T BOTTOM C/SKD

303 4980V01132C SUPPORTER, ASSY AL 42PX4D-UB 0.8T RIGHT C/SKD

304 4980V01134C SUPPORTER, ASSY AL 42PX4D-UB 0.8T LEFT C/SKD

305 5230V00019B FILTER(MECH)- RT-42PX10 FG401PAA-05 LG CHEMICAL GLASS FILTER MECH

400 3809V00513L BACK COVER ASSEMBLY, 42PX4RV-ZA SKD FOR LGEMA NO HANDLE

401 3301V00049B PLATE ASSEMBLY, ASSY 3300V00440A RZ-42PX40 MF056A

410 4980V00C84D SUPPORTER, ASSY AL 42PX4RV-MC LGEAZ CKD PH

430 3501V00216H BOARD ASSEMBLY, ASSY AP-42DX40 PHANTOM 4980V00E63A

501 3301V00055A PLATE ASSEMBLY, AV 3301V00053 3301V00054 RZ-42PX40 ASSY

520 6871VMMD73A PWB(PCB) ASSEMBLY,MAIN MF-056B 42PX4R-ZA XGA MAIN

530 6871VSMS65A PWB(PCB) ASSEMBLY,SUB CONT MF056A HURRICANE2

531 5020V01022B BUTTON. CONTROL DU-42PX51X ABS, AF-303S 8KEY TITAN GRAY

570 6871VSMS27A PWB(PCB) ASSEMBLY,SUB LED MF056A H2 RT-42PX40X INDEX

580 3501V00220A POWER SUPPLY ASSEMBLY, MF056A HURRICANE2 FREE VOLTAGE SANKEN

600 6871VSMS18A PWB(PCB) ASSEMBLY,SUB A/V MF056B H2 50PX4R-ZB SIDE AV

601 4811V00357A BRACKET ASSEMBLY, SIDE AV MF056A SECOND TOOL FOR LGEMA PHANTOM

700 6500VR0002A SENSOR, YGCA-T068A LG INNOTEK AMBIENT LIGHT DIGITAL EYE ASSY

EXPLODED VIEW PARTS LIST

No. Part No. Descriptions

MIC39100 MICREL 3P SOT223 R/TP

BA033FP-E2 ROHM 3P-SOP,TO252-3

KA7809R, FAIRCHILD 2P D-PAK, R/TP

SC156515M-1.8TR SEMTECH 5P/TO-263-5



M62320FP,I/O EXPANDER 16P SOP TP

KA7805R FAIRCHILD 2P D-PAK R/TP 500MA



SC156515M-1.8TR 5P/TO-263-5 R/TP

KIA78R05F KEC 5PIN DPAK R/TP 1A,5V

SC156515M-1.8TR SEMTECH 5P/TO-263-5


SII9011CLU(PB FREE) SILICON IMAGE 128P

AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP

THC63LVD104A 64P TQFP TRAY 10BIT

MC34063ADR2G ON SEMI SO-8P R/TP

CXA2069Q QFP64 BK I2C BUS AV S/W

LA7217M MFP14 TP SYNC SEPARATOR

MSP4410K MICRONAS 80P/PQFP

NSP-2100A,LF NEOFIDELITY TQFP 64P

TAS5122DCARG4,LF 56P/TSSOP R/TP

74HC14D 14SOP TP SHITTER TRIGGER

AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP

74HC14D 14SOP TP SHITTER TRIGGER

ICL3232CBNZ INTERSIL 16P/SOP R/TP



LM75CIMX-3 8P/SOP R/TP TEMPERATURE SENSOR

FLI8125BB-LF GENESIS 208P/PQFP

AT24C32AN-10SI-2.7 8PIN SOP TP 32K 3.3V

SST25VF040-20-4C-S2AE-T SST SOIC 8P

FLI8532BD-LF GENESIS 416P/PBGA

24LC256T-I/SMG(PB FREE) MICRO

SOFT WARE, 2.02V 1491 PDP MF056B

K4D261638F-LC50,LF TSOPII 66P

K4D261638F-LC50,LF TSOPII 66P

SOFT WARE, 2.34V DB9B PDP MF056B

BSS83 TP PHILIPS N-CHANNEL S/W TR








CHIP 2SC3875S(ALY) BK KEC


REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

Q1001

Q1002

Q1003

Q1004

Q101

Q102

Q103

Q103

Q104

Q104

Q105

Q106

Q107

Q108

Q1200

Q200

Q201

Q202

Q203

Q204

Q205

Q206

Q207

Q300

Q301

Q302

Q303

Q304

Q305

Q400

Q401

Q402

Q403

Q404

Q405

Q407

Q408

Q409

Q410

Q411

D1005

D1006

D1007

D1008

D1009

D1010

D1012

D1013

D102

D103

D104

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR102008AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR387500AA

0TR150400BA

0TR150400BA

0TR387500AA

0TR150400BA

0TR150400BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR102008AA

0TR387500AA

0TR102008AA

0TR387500AA

0TR387500AA

0TR387500AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD200009AF

0DD200009AF

0DD226239AA

0DD226239AA

0DD226239AA






KRA102S R/TP KEC SOT23 CHIP TR










CHIP 2SA1504S(ASY) BK KEC

























KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US

RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC


IC1000

IC1001

IC1002

IC1003

IC1004

IC1005

IC101

IC102

IC1100

IC1101

IC1102

IC1103

IC1104

IC1105

IC1200

IC1201

IC1300

IC202

IC300

IC301

IC400

IC401

IC402

IC404

IC500

IC502

IC600

IC601

IC602

IC603

IC700

IC701

IC703

IC800

IC802

IC900

IC901

IC902

S1

IC104

IC105

IC1202

IC1203

IC200

IC201

IC503

IC504

Q100

Q1000

0IPRPML001A

0IMCRRH001A

0IMCRFA010A

0IPMG00027A

0IMCRRH001A

0IMCRRH001A

0IMI623200B

0IMCRFA015A

0IMCRRH001A

0IPRPML001A

0IPMG00027A

0IPMGKE030A

0IPMG00027A

0IPRPML001A

0IPRPS5005A

0IMMRAL014B

0IMCRTH003A

0IPMGON013B

0ISO206900A

0ISA721700C

0IMCRMN028B

0ILNR00015A

0IMCRTI028C

0IPH741400E

0IMMRAL014B

0IPH741400E

0IPRP00009A

0IPMGKE032A

0IPMGKE032A

0IPRPNS054A

0IMCR02006A

0IMMRAL025A

0IMMR00004A

0IMCR02005A

0IMMR00024A

692791001AB

0IMMR00002A

0IMMR00002A

692791002AB

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR387500AA

0TR387500AA

IC

TRANSISTOR

- 26 -

DIODE

- 27 -


D105

D106

D108

D1100

D1105

D1106

D1107

D1109

D1110

D112

D113

D114

D1200

D1201

D300

D500

D501

D502

D504

D505

D506

D600

ZD100

ZD101

ZD107

ZD300

ZD301

ZD400

ZD600

C1000

C1005

C1007

C1009

C1010

C1019

C1022

C103

C1030

C1043

C1046

C1047

C1050

C1051

C1064

C1065

C1066

C1067

C1068

C1069

C1071

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD184009AA

0DS113379BA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DR050008AA

0DR050008AA

0DR050008AA

0DD100009AM

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DZRM00248A

0DR050008AA

0CE477SF6DC

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

0CE4763F618

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE477SF6DC

0CE477SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS184 TP KEC - 85V - 300MA

1SS133 T-72 TP ROHM KOREA DO34 90V

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

SD05.TC R/TP SEMTECH SOD323 5V 5A 15A



EU1ZV(1) TP E/EO-TMD 200V 0.25A 15A 0.4US






RLZ8.2B-TE11 ROHM R/TP LLDS(LL-34


470UF MVG 16V 20% R/TP(SMD) SMD


100UF MVG 16V 20% SMD R/TP





47UF SRE,SE 16V 20% FL TP 5















C1073

C108

C1082

C1083

C1084

C1085

C1087

C109

C1098

C1099

C1102

C1105

C1107

C1108

C1110

C1115

C1116

C1117

C1118

C1119

C1120

C1126

C113

C1135

C1136

C1137

C1138

C114

C1148

C1149

C1150

C1151

C1154

C1159

C116

C1162

C1165

C1166

C117

C118

C1185

C1186

C1187

C1188

C1189

C119

C1190

C1191

C1192

C1193

C1194

C1195

0CE477SF6DC

0CE227SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE106SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE477SF6DC

0CE477DJ618

0CE477SF6DC

0CE227VF6DC

0CE477SF6DC

0CE477DJ618

0CE227VF6DC

0CE477SF6DC

0CE106SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE106SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE227SF6DC

0CE106SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE477SF6DC

0CE107SF6DC
















470UF STD 35V 20% FL TP 5


220UF MV 16V 20% R/TP(SMD) SMD


470UF STD 35V 20% FL TP 5

































CAPACITOR

For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;

CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic

RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible

- 28 -


C1199

C120

C1200

C1201

C121

C1225

C1230

C1231

C1245

C1247

C129

C130

C1302

C1304

C1306

C1309

C131

C1311

C1312

C1313

C1314

C1315

C1316

C1317

C1318

C1333

C1334

C1335

C1338

C135

C1414

C1415

C1419

C1420

C1424

C1425

C1428

C1438

C1441

C1506

C203

C204

C208

C210

C211

C214

C215

C221

C238

C241

C300

C304

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CK105DF64A

0CK105DF64A

0CE106SF6DC

0CE476SF6DC

0CE227SF6DC

0CE227SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE336VF6DC

0CE336VF6DC

0CE336VF6DC

0CE336VF6DC

0CE476SF6DC

0CE475SK6DC

0CE475SK6DC

0CE106SF6DC

0CK105DF64A

0CE106SF6DC

0CE106SH6DC

0CE106SH6DC

0CE106SH6DC

0CE106SH6DC

0CE476SF6DC

0CE475SK6DC

0CE477SF6DC

0CE477SF6DC

0CE475SK6DC

0CE477SF6DC

0CE106SF6DC

0CE475SK6DC

0CE477SF6DC

0CE107SF6DC

0CE476SK6D8

0CE107SF6DC

0CE226SF6DC







1UF 2012 16V 20% R/TP F(Y5V)

1UF 2012 16V 20% R/TP F(Y5V)























4.7UF MVG 50V 20% SMD R/TP



1UF 2012 16V 20% R/TP F(Y5V)
















47UF MVG,MC 50V 20% SMD TAPPING




C305

C307

C310

C315

C318

C319

C320

C321

C325

C328

C330

C338

C340

C342

C347

C402

C403

C413

C418

C425

C444

C451

C456

C457

C462

C463

C464

C465

C480

C481

C482

C483

C484

C495

C527

C610

C614

C615

C620

C621

C622

C728

C729

C730

C731

C735

C737

C739

C745

C750

C752

C760

0CE107SF6DC

0CE476SF6DC

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CE476SF6DC

0CE105SK6DC

0CE105SK6DC

0CE476SF6DC

0CE226SF6DC

0CE335VK6DC

0CE107SF6DC

0CE226SF6DC

0CE107SF6DC

0CK105DF64A

0CK105DF64A

0CE335VK6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SK6DC

0CE108DJ618

0CE475SK6DC

0CE475SK6DC

0CF4741L438

0CF4741L438

0CE108DJ618

0CE476SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC



2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP






3.3UF MV 50V 20% R/TP(SMD) SMD




1UF 2012 16V 20% R/TP F(Y5V)

1UF 2012 16V 20% R/TP F(Y5V)

3.3UF MV 50V 20% R/TP(SMD) SMD





1000UF STD 35V M FL TP5



0.47UF D 63V 5% TP 5 M/PE NI

0.47UF D 63V 5% TP 5 M/PE NI

1000UF STD 35V M FL TP5






















- 29 -


C762

C764

C767

C771

C828

C832

C833

C834

C835

C836

C837

C838

C839

C840

C851

C853

C884

C896

C901

C904

C905

C930

C950

L1000

L1101

L1102

L1103

L1104

L1124

L404

L405

L406

L407

C1

C2

C3

C4

C5

C6

C7

C8

C9

JK500

JK601

AR1200

AR1201

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE106SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0032A

6140VB0032A

6140VB0032A

6140VB0032A

387-G07J

387-J12L

6631V00020J

6631V00045B

6631V12047L

6631V25061D

6631V25083A

6631V39013Z

6631V39018B

6630G70016A

6630G70017A

0RRZVTA001D

0RRZVTA001D
























26UH 1UEWPHY 22.5TURN YL-9N 0.4






DBF-1015A 15.5UH 10PIE DIGITAL AUDIO




7P 2.5MM 500MM H-H UL1007AWG26

12P 2.5MM 700MM H-H UL1185AWG26

3P 3.96MM 400MM H-W UL1672 AWG18

10P SPECIAL 150MM H-H UL1007AWG24

13P 1.25MM 700MM H-H UL1061AWG28

8P 2.5MM 250MM H-H UL1007AWG24

7P 2.5MM 100MM H-H UL1007 AWG24

8P 3.96MM 650MM H-H UL1617AWG22

9P 3.96MM 300MM H-H UL1007AWG18

A03-7071-094 SPG 15P 2.29MM

A02-0915-101 SPG 9P 2.54MM

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24


AR1202

AR1203

AR1204

AR1205

AR1301

AR1302

AR1303

AR1304

AR1305

AR1306

AR700

AR701

AR702

AR703

AR704

AR705

AR806

AR807

AR808

AR809

AR810

AR811

AR812

AR813

AR814

AR815

AR816

AR817

R230

R618

D1003

D1103

IC103

SW101

SW102

SW103

SW104

SW105

SW106

SW107

SW108

SW700

SW800

L100

L1004

L1005

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RRZVTA001B

0RD0331H609

0RD0562H609

0DL233309AC

0DL233309AC

6301V00004A

140-315A

140-315A

140-315A

140-315A

140-315A

140-315A

140-315A

140-315A

6600VR1004A

6600VR1004A

6200J000013

6200J000013

6200J000013

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

MNR14-E0A-J-510 R OHM 51 OHM 5%












3.3 OHM 1/2 W 5.00% TA52

56 OHM 1/2 W 5.00% TA52

SAM2333 GREEN:10MCD, RED:6MCD

SAM2333 GREEN:10MCD, RED:6MCD

YANGWOO RT-42PX41 WHITE LED INDEX

SKHV17910B 12V 0.05A HORIZONTAL 160G








SKHMPW 5P J-ALPS NON .V .A HORIZONTAL .G

SKHMPW 5P J-ALPS NON .V .A HORIZONTAL .G

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM




SWITCH

LED

FILTER & CRYSTALRESISTOR

COIL

CONNECTOR

- 30 -


L1006

L1007

L1008

L1009

L101

L1010

L1011

L1012

L1013

L1014

L1015

L1016

L1017

L1018

L1019

L102

L1020

L1021

L1022

L1023

L1024

L1025

L104

L110

L1105

L1106

L1107

L1108

L1109

L111

L1110

L1111

L1112

L1113

L1115

L1116

L1117

L1118

L1119

L1120

L1121

L1122

L1123

L1125

L1126

L1127

L1128

L1129

L1130

L114

L115

L119

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6210VC0006A

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6210VC0006A

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200JB8010L

6200JB8010L

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA


L120

L1204

L1205

L1206

L1207

L1208

L1209

L121

L122

L123

L124

L125

L126

L1301

L200

L201

L202

L203

L204

L300

L301

L302

L400

L401

L402

L403

L408

L409

L410

L500

L502

L503

L506

L604

L606

L802

X1200

X300

X400

X700

X800

JK100

JK101

JK101

JK102

JK103

JK104

JK1200

JK400

JK502

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6210VC0005A

6210VC0005A

6210VC0005A

6210VC0005A

6210VC0005A

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6212AB2845A

166-E02F

156-A02M

6212AB2844A

6212AB2844A

6612J00043C

6612J00043C

6613V00026A

6612J00043C

6612J10012A

6612J00038B

6612B00015B

6612J00037A

6612F00087A

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

RESONATOR,CRYSTAL ABLS-27.000MHZ

RESONATOR,CERAMIC CSBLA500KECZF09

RESONATOR,CRYSTAL HC49U 18.432MHZ



UPJ-R1-031 UGCOM S/T,SCART,SHIELD,SPRING


UJB-03-28A UGCOM 6613V00004S


UJB-05-02C UGCOM COMPONENT

UJB-03-25B UGCOM 6612J00038A+RED

DC1R019WDH JAE 0.5MM,19PIN+2PIN,HDMI S/T

UJB-02-12A UGCOM 2P RCA VERTICAL+SHIELD

UEJ-CV-032 UGCOM EAR JACK 10MM

JACK

- 31 -


JK600

A1

A2

A3

A4

C10

C11

C12

C13

PA101

TU200

TU201

6612F00087A

3828VA0525F

6710V00151E

6410VEH003C

4972V00178A

6850J00005C

6850VA0004J

6851V00019A

6851V00022C

6712000010A

6700MF0012B

6700MF0012A

UEJ-CV-032 UGCOM EAR JACK 10MM

MANUAL, USER MF056A LG 42PX4RV/EU

REMOTE CONTROLLER, AF05GB 42PX4R-ZA INPUT

POWER CORD, M2511A-001 VDE/SEMKO 2800MM

FIXER, WALL NON ASSY PDP SET

CABLE,DVI LVDS UL20276 AWG30 600MM

CABLE,COAXIAL UL1365#26 150MM UCA-EX-069

CABLE,COAXIAL RF CONN CABLE ASSY 4AC208A0

CABLE,COAXIAL UL1365#26 VW-1

REMOTE CONTROLLER RECEIVER,KSM913TC1E

TUNER, TAFM-W102P PHONO SUB

TUNER, TAUM-W101P PHONO MAIN


ACCESSORIES

MISCELLANEOUS

PRINTED CIRCUIT BOARD

MAIN (TOP) MAIN (BOTTOM )

SIDE A/V(TOP)

CONTROL(TOP)

CONTROL(BOTTOM)

SIDE A/V(BOTTOM)

LED(TOP)

LED(BOTTOM)

Jun., 2005Printed in KoreaP/NO : 3828VD0209S

Documents

Lg 42px4r Za