Upload
trandieu
View
220
Download
0
Embed Size (px)
Citation preview
Lexmark E360
Lexmark E360
Operator panel buttons
Panel Buttons
Panel Buttons
Power-on Self Test (POST) Sequence
Hidden menus
• Configuration Menu
– Reset the PC maintenance counter
– Print Quality pages
– Print reports
• Menu Settings page
• Event Log
– Restore Factory Defaults
– Enable or disable the panel menus
•Entering the Configuration Menu
•Turn off the printer
•Press and hold the select and right arrow keys
•Turn the printer on
•Release the keys when Performing Self Test
displays
Hidden menus
• Diagnostic Menu
– Registration
– Print tests
– Hardware tests
– Duplex tests
– Input /Output tests
– Base sensor tests
• Entering the Diagnostic menu
•Turn off the printer
•Press and hold the select and right arrow keys
•Turn the printer on
•Release the button when Performing Self Test displays
Supplies
Toner cartridge
PC kit
Supplies yield:
Toner Cartridge: up to 9k with High
yield cartridge
PC Kit: Up to 30k
Cross section of EP components
Paper path
Common part replacements and errors
• LVPS/HVPS
–No power, 922.08 fuser error, 923.01 fuser error, print quality problems
• Media feed ACM Clutch
–200.13 or 200.20 paper jams, when printer jams with the leading edge of a second pager overlapping the trailing edge of the first page at the input sensor.
–Special (new) procedure for replacement
• Fuser
–Repeated paper jams at the fuser, print quality, 920.00 – 925.xx error codes
Common part replacements and errors
• ACM assembly
–241.xx paper feed errors, replace the pick tires if worn or dirty, replace the assembly if it is damaged or for mechanical problems
• Transfer roll
–917.xx errors, print quality problems
• Controller board
–902.xx engine software error, 948.xx – 960.xx errors
• PC kit
–Print quality, exhausted or damaged
• Cartridge
–Exhausted , unrecognized or damaged
LV/HVPS removal
• Remove the rear cover first
• Remove the foot on the bottom of the printer
• Remove 4 screws holding securing the shield
• 2 on the bottom of the printer
• 2 on the back of the printer
LV/HVPS removal
• Lift the right side of the LV/HVPS and unplug 3 cables
• Remove 2 cables from the left side
• Remove the power supply
Media Feed Clutch
Remove these parts first:
• Right cover
• Left cover
• Rear cover
• Disconnect the exit sensor from the controller board
Fuser removal
Remove these parts to get to the fuser
• Right cover
• Left cover
• Top cover
• Rear cover
• Rear exit guide
Follow steps for removal in the service procedures
ACM (pick mechanism) removal
Transfer Roll removal
Remove these parts first
• Toner cartridge
• PC kit
• Squeeze the release tabs on the holder arms on the right side and lift this end up.
NOTE: the spring on the right side is not tethered to the frame and may be lost.
• Repeat for the left side.
NOTE: the spring is tethered to the left side.
Transfer roll removal
• Lift the roller out of the printer
NOTE: After installing the transfer roller; it should spring back
when pushed down in the center or on both ends. If it does
not then reseat the roller or poor print quality will result.
Controller board
Remove these parts first:
• Right cover
Follow steps for removal in the service procedures
Combined LVPS/HVPS
This is a combined unit as
opposed to two separate
units as in lots of other laser
printers.
Common error codes relating
to the power supply include:
920.00, .08, .20- 921.00, .01- 922.00,
.08, .09, .20, .21- 923.00, .01- 925.00,
.02- 940.00, .01, .02, .03
• Remove the rear cover
• Remove the right rear foot
asm.
PC Kit
• The PC Kit contains the
photoconductor and
charge roll
• It will usually last through
2 toner cartridges
• If it becomes scratched,
pitted or dirty it will leave
repeating marks on the
printer’s pages
• The counter must be
reset in the configuration
menu when replacing the
pc kit