Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
94
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
0.0 m
1.0 m
2.0 m
3.0 m
4.0 m
5.0 m
12.2 m/s
8.0 m/s
4.9 m/s
4.0 m/s
3.6 m/s
3.2 m/s
AC 400/WAC400
Thermozone® AC 400/WAC 400
Ambient, no heat
Hot water heat
Electrical heat 12�18 kW
Lengths: 1 and 1.7 metres
� Corrosion proof housing made of hot zinc-plate andpowder enamelled steel panels. Colour: RAL 9016
� Compact design requires minimum headroom.� The unit may be tilted to achieve an optimum air
stream angle� The connection areas are easy accessed through a
large service hatch� The sound-absorbing front plate can be turned to
allow air intake either from above or from below� The narrow outlet that gives a high impuls, is
angled 10o outwards for optimum performance
Approved by SEMKO and CE compliant
Air velocity profile
The Thermozone 400 series includes the AC modelswith and without heat, and the hot water heated WACmodels.
AC/WAC 400 are intented for permanent installa-tion above doorways with heigths of between 3 and4.5 meters. By separating zones of different tempera-ture with a jet of air, the AC/WAC400 effectivelyprevents cold draught in open doorways and prov-ides good heating comfort and the opportunity tomake use of the floor space close to the opening.Significantly reduced energy loss gives large savings.
AC400 without heat is specifically designed toprevent loss of cold air through cold room openingsand from shops.
When space above the doorway is limited, theunits can be mounted standing beside the opening,thus creating a sideblowing air stream. They can alsobe mounted in false ceilings.
In wide doorways, several units can be mountednext to each other and regulated with a commonthermostat and control panel. Three different lenghtsmakes it possible to cover openings of differentwidths. When mounting above openings with ceiling-mounted sliding doors, adaptation sets are availablethat position the outgoing air stream close to theopening.
AIR CURTAINS FOR DOORWAYS 3 AND 4.5 METRES
95
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
Hotel Sheraton inStockholm, with 459rooms and 11 suites,is situated only astones-throw from theCentral Station. It is ahigh-class hotel,where the guestsexpect comfort andgood service. Withtwo powerful AC400s,the entrance iscomfortable and freeof draught, and fumes.Dust and insects arealso kept out.
Thermozone AC/WAC400 provides a highly efficient linearair flow barrier. Doors may be left open for long periodsgiving clear, uninterrupted vision and unlimited mobility forpeople and vehicles.
There are AXT401/402 adaptation sets available foropenings with ceiling-mounted sliding doors. With AXT, theoutgoing air stream is positioned as close to the opening aspossible.
The Swedish food stores chain ICA invests in energy savingand air quality. At this store entrance, two AC400s havebeen installed in a vertical position on either side of theentrance to protect the store from fumes and cold air, comingin from the multi-story car park.
The do-it-yourseft store K-rauta saves energy with twoWAC400. The blue shade is the K-rauta´s own colour. If youhave special needs concerning design, positioning orinstallation, please contact the Frico Key Account Team.
96
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
1000 / 1665
975 / 1640 770
360
Thermozone AC 400
360
710
400490
1 1
22
1 alt. 2
335
ø 11
ø 20
Thermozone AC 400 without heat
Type Output stages Air flow Sound level Voltage Amperage Length Weight[kW] [dB(A)] [V] [A] [mm] [kg]
AC401 0/ 1350/2700 44/62 230V~ 2.5 1000 4 4
AC402 0/ 2250/4500 45/63 230V~ 4.2 1670 7 1
Protection class AC400 without heat: (IP24), splash-proof design.
Thermozone AC 400 with electrical heating
Type Output staging Air flow Dt*1 Sound level Voltage[V] Voltage(V) Length Weight[kW] [m3/h] [°C] [dB(A)] Amperage[A] Amperage[A] [mm] [kg]
(control) (heat)
AC412 0/ /12 1350/2700 27/13 44/62 230V~/2.5A 400V3~/17.3A 1000 5 4
AC418 0/ /18 2250/4500 27/13 45/63 230V~/4.2A 400V3~/26.0A 1670 8 6
*1) ∆t = temperature rise of passing air at maximum heat output and lowest/highest air flow.
Protection class AC400 with electrical heating: (IP24), splash-proof design.
Thermozone WAC 400 with hot water heating
Type Air flow Water volume Sound level Voltage Amperage Length Weight[m3/h] [l] [dB(A)] [V] [A] [mm] [kg]
WAC401 1050/2400 2.5 44/62 230V~ 2.5 1000 5 2
WAC402 1800/4000 3.5 45/63 230V~ 4.2 1670 8 3
WAC401V 1050/2400 2.5 44/62 230V~ 2.5 1000 5 2
WAC402V 1800/4000 3.5 45/63 230V~ 4.2 1670 8 3
For vertical mounting: WAC401V and WAC402VProtection class WAC400 with hot water heating: (IP24), splash-proof design.For information on heat output, see output charts on page 103.
TECHNICAL SPECIFICATIONS
DIMENSIONS
97
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
POSITIONING, MOUNTING AND INSTALLATION
Mounting at the side of the openingWhen space above the doorway is limited, modelsWAC401V and WAC402V can be mounted standingbeside the opening, creating a horizontal air stream.Mounting plates AVMP300 are mounted betweenunits and between the lowest unit and the floor. Forminimum mounting distance to doorway, see sketchnr 1 for the electrically heated models.
For maximum performance the units should coverthe whole width of the opening and be fitted as closeto the opening as possible. Several units can bemounted next to each other to form a continuous aircurtain. Maximum building height for vertical unitswithout structural support is 3.5 metres.
Mounting above the openingWith the supplied mounting brackets, ThermozoneAC/WAC400 units may be fitted in several ways: onthe wall, on the ceiling, attached to cables, etc. Thebrackets also allow the units to be tilted in order toachieve an optimum air stream angle.
They can also be mounted in false ceilings, flushwith the ceiling or with only the intake and dischargegrilles visible. Among the hot water heated models,WAC401 and WAC402 are mounted in a horizontalpostion above the opening. For minimum mountingdistance to the doorway see sketch nr 1 for theelectrically heated models. When mounting in falseceilings see sketch nr 2. The units must not bemounted directly below a power point.
For maximum performance the units should coverthe whole width of the opening and be fitted as closeto the opening as possible. Several units can bemounted next to each other to form a continuous aircurtain.
Mounting below ceiling-mounted sliding doorsWhen mounting above openings with ceiling-mounted sliding doors, a square-shaped air curtainunit cannot be positioned close enough to theopening because of the door track. The adaptationset AXT401/402 is dome-shaped and may therefore bepositioned up against the door with the outgoing airstream very close to the opening. When mountingbelow ceiling-mounted sliding doors wires (or similar)for suspension are needed.
98
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
min 200
770
Thermozone AC 400
35 30 1070
1120
945
Connection AC 400 The appliance should be preceded by a triple poleswitch with at least 3 mm breaking gap. Theconnection should be made with a cable type S05VV-U, A05VV-R or similar, through knock outs on the topside of the unit (2 x ø38 mm and 3 x ø29 mm). Forconnection to the supply terminal block, a cable ofmaximum 16 mm2 is used. For connection to thecontrol terminal block, a cable of maximum 6 mm2 isused. For units with electrical heating, power andvoltage should be supplied in different connectionareas. See wiring diagrams on page 106-107.
Connection WAC 400 The appliance should be preceded by a triple poleswitch with at least 3 mm breaking gap. Theconnection should be made with a cable type S05VV-U, A05VV-R or similar, through ø29 mm knock outs onthe top side of the unit. Connections (DN20 (3/4�),inside thread) to the water heating coil are located onthe top of the unit. See sketch 3 and wiring diagramson page 108-109. The supplied 0.8 meter flexiblehoses, allow the unit to be tilted.
Sketch 2: Mounting in false ceiling
Sketch 3: WAC400, water connection on the top side to theright
Sketch 1: Minimum distance to wall 300mm
Sketch 4: Adaptation set AXT401/402.
99
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
REGULATION ALTERNATIVES
ACCESSORIES
Air curtains without heat Fan speed regulationWhen the gate opens and closes, the position limitswitch signals on and off. When on, the fan speed isregulated with a suitable fan speed regulator.
Complete regulation kit:� AGB304, position limit switch� ACR304, 4-stage regulator or
ACR3042, 4-stage regulator high/low speed orACR3042T1, 4-stage regulator high/low speedwith time relay or2221AG, variable fan speed regulator
Air curtains with electrical heating Fan speed and thermostat regulation with positionlimit switchWhen the gate opens and closes, the position limitswitch signals on and off. When on, the fan speed isregulated with a suitable fan speed regulator. The2-stage room thermostat controls the heat supply intwo stages (0, 1/2, 1/1). The output may be manuallycontrolled with an output selector.
Complete regulation kit:� AGB304, position limit switch� ACR304, 4-stage regulator or
ACR3042, 4-stage regulator high/low speed or
KRT2800, 2-stage thermostat Regulates the heat. Adjustable temperature differencebetween the stages (1� 4°C). Setting range 0�40°C.For electrically heated units (AC412, AC418).Protection class: jet-proof design (IP55).
KRT1900, capillary tube thermostat Opens/closes water valves and starts/stops watervalves. A thermostat with alternating relay for controlof heat and fans. For hot water heated units.(WAC401, WAC402, WAC401V, WAC402V).Protection class: jet-proof design (IP55).
KRT1900/2800 RTE102
RTI2, electronic 2-stage thermostat Regulates the heat. Adjustable temperature differencebetween the stages (1� 10°C). Setting range 5�35°C.For electrically heated units (AC412, AC418).Protection class: splash-proof design (IP44).
RTE102, electronic thermostat Opens/closes and starts/stops water valves. Internaltemperature setting 7�35°C. Delivered with coveringframe. Used with hot water heated units (WAC401,WAC402, WAC401V, WAC402V). Protection class:normal design (IP30).
For further alternatives: see section on Thermostats.
RTI2
ACR3042T1, 4-stage regulator high/low speedwith time relay orFRE6, digital variable fan speed regulator
� KRT2800, 2-stage thermostat orRTI2, electronic 2-stage thermostat.
� EV300, output selector
Air curtains with hot water heating Fan speed and thermostat regulation with positionlimit switchWhen the gate opens and closes, the position limitswitch signals on and off. When on, the fan speed isregulated with a suitable fan speed regulator. Theheat supply is controlled by thermostat and by a setof valves. The output may be manually controlledwith an output selector.
Complete regulation kit:� AGB304, position limit switch� ACR304, 4-stage regulator or
ACR3042, 4-stage regulator high/low speed orACR3042T1, 4-stage regulator high/low speedwith time relay or2221AG, variable fan speed regulator orFRE6, digital variable fan speed regulator
� KRT1900, capillary tube thermostat orRTE102, electronic thermostat
� VR20/25, valve set orTVV20/25, valve and SD20, actuator
100
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
AGB304, position limit switchA position limit switch is commonly used to start/stopthe air curtain on opening and closing the door.
ACR304, 4-stage regulator With ACR304, the fan speed can be adjusted in 4stages to achieve optimal performance and protectionat different door heights. The fan is turned off whenthe door closes. The regulator controls a maximum of5�7 units. Max input 14 A. Protection class: splash-proof design (IP 44).
ACR3042, 4-stage regulator high/low speed With ACR3042, the fan speed can be adjusted in 4stages to achieve optimal performance and protectionat different door heights. One speed is selected forwhen the gate is open and a lower speed is selectedfor when the gate is closed. The regulator controls amaximum of 5�7 units. Max input 14 A. Protectionclass: splash-proof design (IP 44).
ACR3042T1, 4-stage regulator
high/low speed with time relay With ACR3042T1, the fan speed can be adjusted in 4stages to achieve optimal performance and protectionat different door heights. One speed is selected forwhen the gate is open and a lower speed is selectedfor when the gate is closed. ACR3042T1 is equippedwith a times relay. When the gate is closed, the fanwill remain at the selected speed for a desired period.This function is particularly useful when a gate isfrequently opened and closed. The regulator controlsa maximum of 5�7 units. Max input 14A. Protectionclass: splash-proof design (IP 44).
2221AG, variable fan speed regulator Single-phase thyristor for variable fan speed controland for switching off and on. Designed for surfacemounting. Fits in rectangular mounting case. Theregulator controls a maximum of 2�3 units. Max input5 A. It regulates hot water heated units (WAC401,WAC402, WAC401V, WAC402V) and units withoutheat (AC401, AC402). Protection class: splash-proofdesign (IP 44).
FRE6, digital variable fan speed regulator s The FRE6 has two different regulation programs tocontrol the air curtain. The UT-regulation that iscontrolled by the door contact, room thermostat andthe outdoor temperature - and the IT-regulation thatis controlled by the door operation. Regulates amaximum of 1-3 units. Max input 6A. With a supplycurrent above 6A, a slave unit must be used. Itregulates hot water heated units (WAC401, WAC402,WAC402V) and electrically heated units (AC418,AC412). Protection class: jet-proof design (IP54).
EV300, output selector Electrically heated units (AC412, AC418) can becontrolled with the output selector EV300. Outputstages: 0�1/2�1/1. Protection class: splash-proofdesign (IP 44).
AGB304 ACR304 2221AG FRE6ACR3042 / ACR3042T1 EV300
101
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
VR 20/25, valve set For regulation of water flow to hot water heatedair curtains.
The valve set consists of the following:� AV20/25, stop valve� JV20/25, adjustment valve� TRV20/25, on/off 3-way motor valve� BPV10, by-pass valve� SD20. actuator on/off
The stop valve (AV20/25) consists of a ball valvewhich is either open or closed. It is used to turn thewater flow off and on. The water flow can be fine-tuned manually with the adjustment valve (JV20/25).It can also be completely turned off. The flow can bemeasured using a pressure port. The kv value forJV20 is 0,13�5,9 and for JV25 0,17� 8,52. The 3-waymotor valve (TRV20/25) consists of a valve motor anda housing. When the TRV20/25 is closed, the flowthrough the by-pass valve is low to ensure presenceof warm water in the heating coil. This leads toinstant heat supply when needed and some degree offrost protection. Actuator SD20 works on/off.
The valve set is available with two different valvedimensions: VR 20 - DN20 (3/4�) and VR 25 - DN25(1�). The by-pass valve dimension is DN10 (3/8�). Toregulate VR20/25, a suitable thermostat has to beadded.
TVV20/25, 2-way regulation valve TVV20 has a pipe dimension of DN20 (3/4�) andTVV25 of DN25 (1�). Pressure class PN16. Maximumpressure 2 MPa (20 bar).Maximum pressure drop TVV20: 100 kPa (0,1 bar)Maximum pressure drop TVV25: 62 kPa (0,062 bar)The kv-value is adjustable in 3 stages:
SD20, actuator on/off 230V~ SD20 regulates the heating. Works on/off. A 5 secondclosing of the valve prevents sudden pressurechanges in the pipe system. IP40.
TVV20/25, 2-way regulation valve and SD20, actuatorprovides a basic form of water regulation, without thepossibility of adjusting or shutting the water flow off.A suitable thermostat is choosen to regulate TVV20/25 and SD20.
Pos. 1 Pos. 2 Pos. 3
TVV20 kv 1,6 kv 2,5 kv 3,5
TVV25 kv 2,5 kv 4,0 kv 5,5
SD20JV20/25 TVV20/25AV20/25
TRV20/25 BPV10
TVV20/25
SD20
KRT, RTE
BPV10
AV20/25
JV20/25
TVR20/25
KRT
VR
20
/25
SD20
230V ~230V ~
C̊ C̊
Thermozone AC 400 Thermozone AC 400
102
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
22003 and 22004, false ceiling grillesThere are false ceiling grilles for air intake anddischarge available for mounting the air curtain infalse ceiling systems. Available in 2 sizes.
AXT401/402, adaptation setWhen mounting above openings with ceiling-mounted sliding doors, adaptation set are availablethat position the outgoing air stream close to theopening.
AVMP300, mounting platesWhen the units are mounted in a standing position atthe side of the door, mounting plates are fittedbetween units and between the lowest unit and thefloor. The mounting plate consists of two parts; theouter one is secured in the floor or at the top of thelower unit; the inner part is mounted on the underside of unit that is standing on the floor.
AXP300, collision protectionAXP300 is mounted on the ground next to a standingair curtain unit to prevent it from being hit by trucks,shopping trolleys etc.
Type Description HxWxD[mm]
KRT2800 2-stage thermostat 165x60x57
KRT1900 Capillary tube thermostat 165x60x57
RTI2 Electronic 2-stage thermostat 150x80x50
RTE102 Electronic thermostat 71x71x28
ABG304 Position limit switch
ACR304 4-stage regulator 100x80x90
ACR3042 4-stage regulator high/low speed 213x155x110
ACR3042T1 4-stage regulator high/low speed with time relay 213x155x110
2221AG Variable fan speed regulator 170x85x63
FRE6 Digital variable fan speed regulator 180x210x110
EV300 Output selector 100x80x90
VR20 Valve set, connection DN20
VR25 Valve set, connection DN25
TVV20 2-way valve, connection DN20
TVV25 2-way valve, connection DN25
SD20 Actuator on/off
22003 False ceiling grille 1192x192
22004 False ceiling grille 1515x192
AVMP300 Mounting plates
AXT401 Adaptation set for ceiling-mounted sliding doors 1000
AXT402 Adaptation set for ceiling-mounteds sliding doors 1670
AXP300 Collision protection
AXT401/402 AVMP300 AXP30022003/22004
103
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
OUTPUT CHARTS WATER
Incoming / outgoing water temperature 80/60°CIncoming air temp. = +15°C Incoming air temp. = +20°C
Type Fan Air Output Outgoing Water- Output Outgoing. Water-position flow air temp. flow air temp. flow
[m3/h] [kW] [°C] [l/s] [kW] [°C] [l/s]
WAC401 max 2400 32.9 55.4 0.39 29.8 56.6 0.35
m i n 1050 17.9 65.3 0.21 16.3 65.7 0.19
WAC402 max 4000 56.6 56.8 0.67 51.4 57.9 0.61
m i n 1800 31.3 66.2 0.37 28.5 66.7 0.34
WAC401V max 2400 30.0 51.8 0.35 27.1 53.3 0.32
m i n 1050 16.7 61.9 0.19 15.1 62.5 0.18
WAC402V max 4000 49.3 51.3 0.58 44.5 52.8 0.53
m i n 1800 28.1 61.1 0.33 25.5 61.7 0.30
Incoming / outgoing water temperature 60/40°CIncoming air temp. = +15°C Incoming air temp. = +20°C
Type Fan Air Output Outgoing Water- Output Outgoing. Water-position flow air temp. flow air temp. flow
[m3/h] [kW] [°C] [l/s] [kW] [°C] [l/s]
WAC401 max 2400 20.0 39.6 0.23 16.9 40.7 0.20
m i n 1050 11.2 46.4 0.13 9.5 46.7 0.11
WAC402 max 4000 35.0 40.8 0.41 29.6 41.8 0.35
m i n 1800 19.8 47.4 0.23 16.9 47.6 0.20
WAC401V max 2400 17.8 36.8 0.21 14.8 38.2 0.17
m i n 1050 10.2 43.6 0.12 8.6 44.1 0.10
WAC402V max 4000 28.8 36.2 0.34 23.9 37.6 0.28
m i n 1800 16.9 42.7 0.20 14.2 43.2 0.16
Incoming / outgoing water temperature 60/30°CIncoming air temp. = +15°C Incoming air temp. = +20°C
Type Fan Air Output Outgoing Water- Output Outgoing. Water-position flow air temp. flow air temp. flow
[m3/h] [kW] [°C] [l/s] [kW] [°C] [l/s]
WAC401 max 2400 15.3 33.7 0.12 11.7 34.4 0.09
m i n 1050 8.9 40.0 0.07 7.0 39.6 0.05
WAC402 max 4000 27.3 35.1 0.21 21.2 35.7 0.16
m i n 1800 16.1 41.3 0.12 12.7 40.9 0.10
WAC401V max 2400 12.8 30.7 0.10 9.5 31.7 0.07
m i n 1050 7.7 36.6 0.06 5.9 36.4 0.04
WAC402V max 4000 20.1 29.8 0.16 14.7 30.9 0.11
m i n 1800 12.4 35.4 0.09 9.3 35.3 0.07
Incoming / outgoing water temperature 55/35°CIncoming air temp. = +15°C Incoming air temp. = +20°C
Type Fan Air Output Outgoing Water- Output Outgoing. Water-position flow air temp. flow air temp. flow
[m3/h] [kW] [°C] [l/s] [kW] [°C] [l/s]
WAC401 max 2400 16.7 35.6 0.19 13.5 36.6 0.16
m i n 1050 9.5 41.6 0.11 7.7 41.7 0.09
WAC402 max 4000 29.4 36.7 0.35 23.9 37.6 0.28
m i n 1800 16.8 42.5 0.20 13.8 42.7 0.16
WAC401V max 2400 14.6 33.0 0.17 11.6 34.3 0.13
m i n 1050 8.5 38.8 0.10 6.8 39.2 0.08
WAC402V max 4000 23.6 32.4 0.28 18.6 33.7 0.22
m i n 1800 14.0 38.0 0.16 11.2 38.4 0.13
104
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
V V
0.01 0.1 1.0
1 0
7 0
1
0.1 1.0 1 0
0.01 0.1 1.0
1 0
7 0
1
0.1 1.0 1 0
0.1
0.7
0.01
0.1
0.7
0.01
WA
C40
2
WAC
402V
WAC40
1W
AC40
1V
Water pressure drop over WAC 400 water coil
Water pressure drop over regulations and valves
Water flow [l/s]
Water flow [m3/h]
Water flow [l/s]
Pre
ssur
e dr
op [
kPa]
Pre
ssur
e dr
op [
bar]
The pressure drop is calculated for an average temperature of 70°C (PVV 80/60).
For other water temperatures, the pressure drop is multiplied with the factor K.
Average temp. water °C 4 0 5 0 6 0 7 0 8 0 9 0
K 1.10 1.06 1.03 1.00 0.97 0.93
PRESSURE DROP WATERP
ress
ure
drop
[kP
a]
Pre
ssur
e dr
op [
bar]
Water flow [m3/h]
105
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
1 2 3 4
NP 1 2 3 4
NP
L1 N (L2)230 V~
~N
321 4 5 6 7 8 9NP
NL
L1 N (L2)230 V~
M~ c̊ M~ c̊ c̊
NL L
PTC
NL
M~ c̊ M~ c̊
4321
1 3 5 70
XXX
X
X
XXXX
2 6 8
1 5 73
NP 1 2 3 4 5 6 9
4 5 6 9
L1 N (L2)230 V~
2 6 8
1 5 73
AGB304
AC401/AC402
~N
1 2 3 4
NP 1 2 3 4
NP
L1 N (L2)230 V~
ACR304
AGB304
AGB304
AC401
AC401
AC401/402
AC401/402
AC401
AC401
ACR304
WIRING DIAGRAMS AC401 AND AC402
Manual 4-stage fan speed regulation with ACR304, start/stop with position limit switch AGB304
Fan speed adjustment in 4 stages with ACR304,start/stop with position limit switch AGB304
Variable fan speed adjustment with thyristor2221AG, start/stop with position limit switchAGB304
Variable fan speed adjustment with thyristor2221AG
ACR304,4-stage regulator
When the motor current exceeds6 A, a contactor should beconnected parallely with the positionlimit switch.
AGB304,position limit switch
2221AG,variable fanspeed regulator
AGB304,position limitswitch
2221AG,variable fanspeed regulator
ACR304,4-stage regulator
AGB304,position limitswitch
Maximum current for the variable fan speedregulator 2221AG is 5A. It can regulate:2 x AC401 or 1 x AC402
AC401/AC402
2221AG
2221AG
106
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
NP 1 2 3 4 5 6 7
4 5 6
10 12 13 14 15
10 12 13 14 15
5 1
6 2
L1 L2 L3
L1 L2 L3
400V3~/230V3~
400V3~/230V3~
L1 N (L2)230 V~
L1 N (L2)230 V~
NP1 2 3 4 65 7
c̊
Hi Lo4321
1 3 5 70
XXX
X
X
XXXX
2 6 8
1 5 73
4
6 2O
XX
X
AC412/418
RTI2
EV300
ACR304AGB304
321 4 5 6 7 8 9NP
NL
L1 N (L2)230 V~
400V 3~/230V 3~
M~ c̊ M~ c̊ c̊
NL L
PTC
4321
1 3 5 70
XXX
X
X
XXXX
230 V3~
123
Hi
Lo
Diff (1-4)K
123
5 1
6 2
6 2O
XX
X
L1 L2 L313 15121110
K3K1 K2
c̊
c̊
NL
M~ c̊ M~ M~c̊
400 V3~
14
2 6 8
1 5 73
AC412/418
KRT2800
EV300ACR304
AGB304
AC412/418
Manual 4-stage fan speed regulation with ACR304, start/stop with position limit switch AGB304, automatic 2-stage heat regulation with thermostat RTI2, output selection 0�½�1 output with EV300
AGB304,position limit switch
ACR304,4-stage regulator
EV300,output selector
RTI2,electronic2-stagethermostat
WIRING DIAGRAMS AC412 AND AC418
Manual 4-stage fan speed regulation with ACR304, start/stop with position limit switch AGB304, automatic2-stage heat regulation with thermostat KRT2800, output selection 0�½�1 output with EV300
AGB304,position limit switch
ACR304,4-stage regulator
EV300,output selector
KRT2800,2-stagethermostat
AC412,AC418
When the motor current exceeds6 A, a contactor should beconnected parallely with the positionlimit switch.
107
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
NP 1 2 3 4 5 6 7
3132 33 34 35 36 37 38
4 5 6
10 12 13 14 15
10 12 13 14 15
1 2 3 4
X
X
X
X
X
X
X
XX
5 1
6 2
L1 L2 L3
L1 L2 L3
400V3~/230V3~
400V3~/230V3~
L1 N (L2)230 V~
L1 N (L2)230 V~
NP1 2 3 4 65 7
c̊
Hi Lo
AC412/418
AC412/418
AGB304
ACR3042
EV300
RTI2
NP 1 2 3 4 5 6 7
3132 33 34 35 36 37 38
4 5 6
10 12 13 14 15
10 12 13 14 15
1 2 3 4
X
X
X
X
X
X
X
XX
123
Hi
Lo
Diff (1-4)K
123
5 1
6 2
L1 L2 L3
L1 L2 L3
400V3~/230V3~
400V3~/230V3~
L1 N (L2)230 V~
6 2O
XX
X
AC412/418
AC412/418
AGB304
ACR3042
EV300
KRT2800
WIRING DIAGRAMS AC412 AND AC418
High/low fan speed with position limit switch AGB304 and ACR3042, automatic 2-stage heat regulationwith thermostat RTI2, output selection 0�½�1 output with EV300
ACR3042,4-stage
regulator
AGB304,posit ion
limit switch
EV300,output selector
High/low fan speed with position limit switch AGB304 and ACR3042, automatic 2-stage heat regulationwith thermostat KRT2800, output selection 0�½�1 output with EV300
ACR3042,4-stage
regulator
AGB304,posit ion
limit switch
EV300,outputselector
KRT2800,2-stagethermostat
RTI2,electronic2-stagethermostat
AC412,AC418
AC412,AC418
108
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
NP 1 2 3 4 5 6 9
230 V~
NL N U 1 2TK 5 6 101112TK 21222324
NP 1 2 3 4 5 6 9
21
3c̊
TRV/TVV
SD20
NP 1 2 3 4 5 6 7
230 V~
10 12 13 14 L1 L2 L3
400V3~/230V3~
NL N U 1 2TK 5 6 101112TK 21222324
51
62
8 9
6 2O
XX
X
NL 1 2
NP 1 2 3 4 5 6 7 10 12 13 14 L1 L2 L3
400V3~/230V3~
8 9 15
15
21
3c̊
WAC401-WAC402V
EV300
FRE6
FRE6
WAC401-WAC402V
AC412/418
AC412/418
KRT
KRT
WIRING DIAGRAMS WAC401, WAC401V, WAC402 AND WAC402V
WIRING DIAGRAMS AC412 AND AC418
Outdoor compensated variable fan speed regulation with FRE6
SD20, actuator, on/off, 230V~
TRV/TVV20/25
Outdoor compensated variable fan speed regulation with FRE6, effect limitation with the output selectorEV300 in effect stages 0-1/2-1
Outdoorsensor
Roomthermostat
Door contact
Outdoorsensor
Roomthermostat
Door contact
AC412-AC418
EV300,output selector
FRE6,dig i ta l
variable fanspeed regulator
WAC401(V)/402(V)
FRE6,dig i ta l
variable fanspeed regulator
FRE6 regulates a maximum of 4 xWAC401(V) or 2 x WAC402(V)
FRE6 regulates a maximum of 4 x AC412 or 2 xAC418
109
THERMOZONE AC 400/ WAC 400
Frico AB, Box 102, SE-433 22 Partille � Tel: +46 31-336 86 00 � Fax: +46 31-26 28 60 � [email protected] � www.frico.seDesign and specifications are subject to change without notice.
321 4 5 6 7 8 9NP
NL
M~ c̊ M~ c̊ c̊
NL L
PTC
4321
1 3 5 70
XXX
X
X
XXXX
NL
M~ c̊ M~ M~c̊
123
12345
L1
230 V~N (L2)
2 6 8
1 5 73
SD20
TRV/TVV
KRT1900
RTE
ACR304
AGB304
NP 1 2 3 4 5 6 9
3132 33 34 35 36 37 38
4 5 6 9
1 2 3 4
X
X
X
X
X
X
X
XX
123
12345
L1
230 V~N (L2)
AGB304
SD20
TRV/TVV
RTE102
KRT1900
WAC401-WAC402V
WAC401-WAC402V
ACR3042
WAC401-WAC402V
For variable fan speedcontrol, see wiringdiagrams on page 105.
WIRING DIAGRAMS WAC401, WAC401V, WAC402, WAC402V
KRT1900capillary tube
thermostat
RTE102,electronicthermostat
TRV/TVV20/25
SD20, actuator, on/off, 230V~
ACR304,4-stage regulator
High/low fan speed with position limit switch AGB304 and ACR3042, automatic heat regulation withthermostat RTE/KRT, actuator SD20 and valve TVV20/25
ACR3042,4-stage regulator
AGB304,position limitswitch
KRT1900,capillary
tubethermostat
RTE102,electronicthermostat
TRV/TVV20/25
SD20, actuator, on/off, 230V~
Manual 4-stage fan speed regulation with ACR304, start/stop with position limit switch AGB304, automaticheat regulation with thermostat RTE/KRT, actuator SD20 and valve TVV20/25
AGB304,position limitswitch
WAC401(V)/402(V)
WAC401(V)/402(V)