LED LUMINAIRE - IMPORTANT SAFETY INSTRUCTIONS

MODEL 73995

LIMITED WARRANTY This product is warranted to be free from defects in workmanship and materials for up to 3 years from date of purchase. If it fails to do so, please contact Feit Electric at info@feit.com or call 1-866 326-BULB (2852) for instructions on replacement. Do not return the product to the store.

1.25”(32mm)

2.35”(59.7mm)

Mounting Hardware Included1. Remove fixture components and parts pack. Check that all parts are included.

Turn OFF Power at circuit breaker box. CAUTION:Do not rely on wall switch alone to turn off power

Fixture Mounting

Note: Hardware included for mounting to wood surfaces only. Ensure that fixture is mounted onto structurally sound surface that will support the fixture.

Optional Mounting Arm available (sold separately)

2. Using the template on the box, mark mounting holes locations and drill 5/32” diameter pilot holes. See Fig 2

CAUTION: WIRING AND FIXTURE OPERATION Make sure power is turned off.

3. Install the three 2” Screws (4) (or other appropriate mounting hardware) into the predrilled hole on top and back the Screw out. This will leave the hole threaded and make installation easier. See Fig 14. Unscrew the M6 Screws (7) from handle.remover the cover plate (8).5. Assemble the handle to the housing assembly, secure the housing assembly tothe wall with 2” Screws.6. Pass fixture wires into two openings on cover plate, feed the wires into outside conduit. Reassemble the cover plate to handle with M6 Screws (7) and unts (6).

For proper connection, place wire nut over wires and twist clockwise until tight.

FIXTURE PACKING LISTDescription Quantity(1)Housing Assembly.....................................(2)LED Bulb................................................... (3)Photocontrol.............................................. (4)2” Screws................................................... (5)Wire Nuts................................................... (6)M6 Nuts .................................................... (7)M6 Screws ................................................ (8)Cover Plate ..................................................(9)Handle........................................................

111332211

!

Fig 1

Fig 2

Note: NOT suitable for use with dimmers, motion sensors or other remote devices.

7. Use conduit and fittings (not supplied) to connect between the cover plate and a properly installed and grounded UL listed junction box (not supplied). 8. Connect supply wiresUse Wire Nuts (5) to connect the black fixture wire to the black power supply wire and the white fixture wire to the white (neutral) supply wire. 9. Install the LED bulb (2).10. Turn on electricity at fuse or circuit breaker box and verity success of installation. Note: Test fixture at night or block photocontrol.

Conduit & Fitting(Not Supplied)

(1)Housing Assembly

(3)Photocontrol(4)2” Screws

(5)Wire Nuts

(6)M6 Nuts

(7)M6 Screws

(8)Cover Plate

(2)LED Bulb

MODEL 73995

LED LUMINAIRE - IMPORTANT SAFETY INSTRUCTIONS

(9)Handle

Fig 3(1)Housing Assembly

(3)Photocontrol

(4)2” Screws

(5)Wire Nuts

(6)M6 Nuts

(7)M6 Screws

(8)Cover Plate

(2)LED Bulb

LED LUMINAIRE - IMPORTANT SAFETY INSTRUCTIONS

(9)Handle

Recommend use the diameter 1.5”

Trouble Shooting GuideIf this fixture fails to operate properly, use the guide below to diagnose and correct the problem. Verify that power is turned on at switch and breaker. Verify that fixture is wired properly. Verify that line voltage is correct. Test if Photocontrol works properly.The photocontrol in this fixture is designed to turn on fixture light at low light levels.If light does not come on or stays on:Test if Photocontrol works properly: Cover Photocontrol - Light should come on. Shine a flashlight into Photocontrol - Light should go off.If fixture cycles on and off:Light reflecting back off any surrounding surfaces enters the photocontrol. To correct problem, reposition the fixture or eliminate reflective surface.

Pole Mount Option (Fig 3)

1. Mount arm assembly in desired location firmly.2. Unscrew the M6 Screws (7) from handle,remove the cover plate (8), assemble the handle to the housing assembly. 3. Pass fixture wires into one opening on vertical cover plate (8). Reassemble the cover plate (8) to handle with M6 Screws (7) and nuts (6).4. Feed supply wires up through mountingarm, use wire nuts (5) to connect neutral, line and grounding wires (black/white/green-yellow). Push the wires and connectors into arm.5. Move the housing assembly toward armuntil there is no gap between the arm and the vertical cover plate (8).6. Secure the M6 Screws (7) and nuts (6) of cover plate (8) firmly.7. Install the LED bulb (2).

MODEL 73995