Learn Loads

Alphabetical list of prompts Page 89 of 1082

Administration

LD 10

Alphabetical list of prompts

Prompt Response Comment Pack/Rel

AACD (NO) YES Associate set (AST) ACD telephone ism-17

ADAY (0)-3 Alternate Days as defined in LD 15

Prompted if CLS = RBDA

basic-24

AHOL (0)-3 Alternate Redirection Holiday as defined in LD 15

Prompted if CLS = RBHA

basic-24

ANIE (0)-n ANI Entry: it is of (0)-N where N=S_SIZE in customer datablock.

If ANIE=0, no entry is associated with the set. The oldmechanism will be used for building the ANI message.

If ANIE is of 1-N:

• If ANIC = YES for the outgoing CIS route wherethe call takes place, then the components of theANI message are retrieved from the ANI entry inCustomer Data Block, if configured.

• If the given ANI Entry is not configured, or if ANIC= NO for the outgoing CIS route where the calltakes place, then the old mechanism is used forbuilding the ANI message.

cist-24

ARTO (0)-3 Alternate Redirection Time Option for call redirection,defined in the customer data block. Prompted ifCLS = RTDA.

basic-22

AST (NO) YES Associate Set assignment iap3-12For sets associated with ISDN Applications Protocolfeatures.

AUTH n xxxx Authorization code. Where:

• n = number (1-6) of assigned authorization code• xxxx = assigned authorization code (Any customer

authorization code assigned in LD 88 is valid.)

AUTH is prompted when CLS = AUTR (Class of Service =Authorization code required).

ssau-19

Page 90 of 1082 Alphabetical list of prompts

553-3001-311 Standard 9.00 January 2002

LD 10

BIMP Balance Impedance for Enhanced Off-Premise Station(XOPS) unit

basic-20

600 600 ohms. This is the default, except when CLS = OPS.900 900 ohms3COM 3 component3CM2 3 component 2. This is the default if CLS = OPS.

CAC Category code mfc-14(0)-10 Category Code range for outgoing CNI of MFC trunks

when Multifrequency Compelled Signaling (MFC)package 128 is equipped.

0-(3)-9 Category Code for CIS ANI when Commonwealth ofIndependent States (CIST) package 211 is equipped.

cist-21

CAC_CIS

0-(3)-9 CIS ANI Category Access Code cist-24

CAC_MFC

(0)-10 MFC CNI Category Access Code cist-24

CDEN SD Single Density Card basic-7DD Double Density Card4D Quadruple Density Card8D Octal Density Card

XOPS cards are configured as DD on superloops or smallsystems.

If REQ=NEW and the loop is a superloop, the default is4D. If REQ=NEW and the XOPS card is to be configuredon the loop, set CDEN to DD. If REQ=CHG, the carddensity is not changed.

Note: If a QPC192 (off-premises extension) card is configured insuperloop, then the response for CDEN should be QuadrupleDensity.

CFTNl s c u

Copy From Terminal Number. Prompted if REQ = CPY.For large system

basic-12

c u For small systemUse this TN as a template for the new sets. Associate set(AST) assignments are not copied to the new telephones.



Administration

LD 10

CLS CLS Class of Service options

The following CLS assignments determine the callingoptions and features available to an analog telephone.Defaults are shown in parentheses. Enter eachnon-default option required, separated by a space.

basic-1

Access Restrictions basic-1(CTD)UNRCUNTLDSREFREFR1FR2

Conditionally Toll Denied (default)UnrestrictedConditionally Unrestricted.Toll Denied.Semi-Restricted.Fully Restricted.Fully Restricted 1.Fully Restricted 2.

(ABDD) Abandoned call record and time to answer denied fcdr-18ABDA Abandoned call record and time to answer allowed

(AGTD) ACD services for 500/2500 type telephone sets denied phtn-20AGTA ACD services for 500/2500 type telephone sets allowed

An AGTA entry will not be validated if you do not defineFEAT = ACD in the same pass through this overlay.

(ALCA) ALC loss plan class A port type cdr-18ALCB ALC loss plan class B port type

(ARHD) Audible Reminder of Held Call Denied basic-14ARHA Audible Reminder of Held Call Allowed

(ASCD) Alarm Security Denied ohas-18ASCA Alarm Security Allowed

Mutually exclusive with Three-Party Service Allowed(TSA)

(AUTU) Unrestricted Authcode ssau-19AUTD Denied AuthcodeAUTR Restricted Authcode

When the CLS is changed from AUTR to either AUTU orAUTD, all previous telephone authorization codeinformation is removed. Must have Station SpecificAuthorization Codes (SSAU) package 229.




LD 10

(BNRD) Busy Number Redial Denied ffc-21BNRA Busy Number Redial Allowed

Must have ADL configured and Flexible Feature Codes(FFC) package 139.

(C6D) Six-Party Conference Denied basic-10C6A Six-Party Conference Allowed

C6A requires Transfer Allowed (XFA) Class of Service.

(CCBD) Collect Call Blocking Denied (permits a set to acceptcollect calls)

ccb-21

CCBA Collect Call Blocking Allowed (prevents a set fromaccepting collect calls)Must have Collect Call Blocking (CCB) package 290.

(CCSD) Controlled Class of Service Denied phtn-20CCSA Controlled Class of Service Allowed

CCSA is required for the Electronic Lock feature. See theFlexible Feature Codes section in the Features andServices (553-3001-306). Must have Controlled Class ofService (CCOS) package 81.

(CDMD) CDMD denies record generation emct-20CDMA CDMA allows external station activity records to be

generated for the set

(CFHD) Call Forward/HUNT Override Denied cfho-20CFHA Call Forward/HUNT Override Allowed

(CFTD) Call Forward by Call Type Denied opft-10CFTA Call Forward by Call Type Allowed

Call Forward by Call Type enhances Hunt and CallForward No Answer. CFTA requires Hunting Allowed(HTA) and/or Call Forward Allowed (FNA) Class ofService.



Administration

LD 10

(CFXD) Call Forward All Calls to external DN Denied optf-19CFXA Call Forward All Calls to external DN Allowed

Examples of external DNs are:

• Route Access Code• ESN Access Code• CDP Distant Steering Code

When Denied, a call can only be forwarded to thefollowing internal DNs:

• Single or multi-line telephone• Attendant DN or CAS local attendant DN• Listed DN as defined in LD 15• Message center DN where MWC = YES

(CLBD) Deactivate Calling Party Number and Name per-lineblocking

cpp-21

CLBA Activate Calling Party Number and Name per-lineblockingThe user may still request CPP by dialing the CPP code.

(CLTD) Network Call Trace from this telephone Denied pra-17CLTA Network Call Trace from this telephone Allowed

(CNAD) CLASS Calling Name Denied. cname-23CNAA CLASS Calling Name Multiple Data Format Allowed.

Note: CNUD/CNUD/CNUS/CNAD/CNAA are not a validinput for a Dial Intercom Group (DIG) set.

(CNAD) CLASS Calling Name Denied. cname-23CNAA CLASS Calling Name Multiple Data Format Allowed.

Note: CNUD/CNUD/CNUS/CNAD/CNAA are not a validinput for a Dial Intercom Group (DIG) set.

(CNDD) Call Number Display Denied mcmo-20CNDA Call Number Display Allowed

Allows user to see calling or called name associated withthe number dialed if CPND is set up for the customerassociated with the portable personal telephone. Allowedif WRLS = YES.




LD 10

(CNID) Call Number Information Denied bgd-10CNIA Call Number Information Allowed

(CNUD) CLASS Calling Number Delivery Denied. cnumb-23CNUA CLASS Calling Number Multiple Data Format Allowed.CNUS CLASS Calling Number Single Data Format Allowed.

(CPFA) Forced Camp-On from another set Allowed scmp-15CPFD Forced Camp-On from another set Denied

(CPTA) Forced Camp-On to another set Allowed scmp-15CPTD Forced Camp-On to another set Denied

(CRD) Continuous Ring Denied scmp-15CRA Continuous Ring Allowed

(CWD) Call Waiting Denied basic-1CWA Call Waiting Allowed

The telephone should also have CLS = HTD(Hunting Denied) since hunting takes precedence.

(CWND) Call Waiting Notification Denied cwnt-19CWNA Call Waiting Notification Allowed

Must have Call Waiting Notification (CWNT) package 225.

(DDGA) DN display on other set Allowed dpd-21DDGD DN display on other set Denied

(DNAA) DN of set will be used in 3WT ANI messages. cist-21DNAD Outgoing 3WT route will be used as DN in 3WT ANI

messages.Must have Commonwealth of Independent States (CIST)package 221.

(DNDY) Diversion Notification with called party’s number andname when available.

qsigss-23

DNDN Diversion Notification without called party’s number andname.

(DNO3) Diversion Notification Option with diverted-to party’snumber and name when available.

qsigss-23

DNO1 Diversion Notification Option without notification.DNO2 Diversion Notification Option without diverted-to party’s

number and name.



Administration

LD 10

(DTN) Digitone. DTN is used for 2500, UNITY and digitonetelephones.

basic-20

DIP Dial Pulse. DIP is used for 500, rotary and dial pulsetelephones.

MNL Manual service. MNL is used for manual service to theattendant and Flexible Hot Line

(DPUD) DN Pickup Denied dcp-12DPUA DN Pickup Allowed

DN Pickup is not allowed on telephones in group zero(RNPG = 0). Must have Directed Call Pickup (DCP)package 115.

(DSH) Digital Short telephone set ida-16DLO Digital Long telephone set

Select DLO for line lengths of 2 km or 1.2 miles or more.Must have Integrated Digital Access (IDA) package 122.

(EHTD) Enhanced Hot Line Denied phtn-20EHTA Enhanced Hot Line Allowed

Cannot be assigned with LLC1, LLC2, LLC3, LNA, MNLor Permanent Hold feature.

(EXR0) Executive Distinctive Ringing Off 0 edrg-16EXR1 Executive Distinctive Ringing On 1EXR2 Executive Distinctive Ringing On 2EXR3 Executive Distinctive Ringing On 3EXR4 Executive Distinctive Ringing On 4

The digit indicates which of the four distinctive ringingtones and cadences defined in LD 56 is to be used. Musthave Executive Distinctive Ringing (EDRG) package 185.

(FAXD) Fax denied euroisdn-22

FAXA Fax allowed. ISDN call is generated with 3.1 KHz BearerCapability. Set is a modem or a FAX machine.




LD 10

(FBD) Call Forward Busy Denied basic-1FBA Call Forward Busy Allowed

Call Forward Busy Allowed sends DID calls whichencounter a busy condition to the attendant. Call ForwardBusy should have Hunting and Call Waiting Denied orCLS = HTD and CWD, since Hunting and Call Waitingtake precedence over FBA.

(FDSD)FDSA

Force Disconnect DeniedForce Disconnect Allowed

ponw-25.4

(FND) Call Forward No answer Denied basic-1FNA Call Forward No answer Allowed

(FTTC) Flexible Trunk to Trunk Connections Conditional allowstrunk to trunk connections for supervised Conference.

basic-23

FTTR Flexible Trunk to Trunk Connections Restricted deniestrunk to trunk connections for Transfer and unsupervisedConference.

FTTU Flexible Trunk to Trunk Connections Unrestricted allowstrunk to trunk connections for both Conference andTransfer.

(GPUD) Group Pickup Denied dcp-12GPUA Group Pickup Allowed

Group Pickup is not allowed on telephones in group zero.Must have Directed Call Pickup (DCP) package 115.

(HBTD) Hunt By call Type Denied basic-10HBTA Hunt By call Type Allowed

(HSPD) Hospitality Denied. HSPD is for administration sets. hvs-16HSPA Hospitality Allowed. HSPA is for room sets.

For HSPA, you must also enter CLS = CCSA andCLS = MRA. HSPA CLS cannot be entered for a set withtransfer or conference capability. This feature is used forHospitality Management.

(HTD) Hunting Denied basic-1HTA Hunting Allowed



Administration

LD 10

(IAMD) ICP Answering Machine Denied icp-16IAMA ICP Answering Machine Allowed

This features allows a 2500 set to be a channel in theIntercept Computer Interface (ICP) Answering Machine.

(ICDD) Internal Call Detail Recording Denied icdr-10ICDA Internal Call Detail Recording Allowed

(IRGD) Interrogation set Denied for intercept computer icp-14IRGA Interrogation set Allowed for intercept computer

(LDTD) Line Disconnect Tone Denied basic-17LDTA Line Disconnect Tone Allowed

(LLCN) Line Load Control off llc-13LLC1 Line Load Control Class 1LLC2 Line Load Control Class 2LLC3 Line Load Control Class 3

(LND) Last Number Redial Denied lnr-8LNA Last Number Redial Allowed

Must have OPT = LRA in LD 15

(LPD) Message Waiting Lamp Denied phtn-20LPA Message Waiting Lamp Allowed

If a modem is connected to a port on the message waitingline card, that port should be defined as LPD. With LPAthe modem may be damaged by the message waitinglamp voltage 150 V.

(LPR) Low Priority station povr-1HPR High Priority station

High Priority will place this set or trunk at the top of thedial tone queue.

(MBXD) Multi-Party Operation (MPO) Blind Transfer Denied.When CLS = MBXD, blind transfers occur withmis-operation treatment.

mpo-21

MBXA Multi-Party Operation (MPO) Blind Transfer Allowed.When CLS = MBXA, blind transfers occur withoutmis-operation treatment. To configure CLS = MBXA, CLSmust first be defined as TSA or XFA.Multi-Party Operations (MPO) package 141 must beequipped to enter MBXD or MBXA.




LD 10

(MCRD) Multiple Call Arrangement Denied basic-15MCRA Multiple Call Arrangement Allowed

(MCTD) Malicious Call Trace signal Denied mct-10MCTA Malicious Call Trace signal Allowed

MCT is applied on a TN basis.

(MIND) Message Interrupt Denied mr-15MINA Message Interrupt Allowed

(MRD) Message Registration Denied mr-10MRA Message Registration Allowed

(MWD) Message Waiting Denied mwc-1MWA Message Waiting Allowed

(NAMA) Name display Allowed dpd-21NAMD Name display Denied

(NOVD)NOVA

Network Override/Breakin DeniedNetwork Override/Breakin Allowed

ponw-25.4

(NRCD) Night Restriction for forced Camp-On Denied povr-16NRCA Night Restriction for forced Camp-On Allowed

If night restriction is allowed, then forced Camp-On for thisset is allowed during night service only.

(NROD) Night Restriction for Priority Override Denied povr-16NROA Night Restriction for Priority Override Allowed

If night restriction is allowed, then Priority Override for thisset is allowed during night service only.

(NRWD) Night Restriction for Call Waiting Denied povr-16NRWA Night Restriction for Call Waiting Allowed

If Night Restriction is allowed, then Call Waiting for this setis allowed during night service only.

(OCBD) Outgoing Call Barring Denied ccb-21OCBA Outgoing Call Barring Allowed

Must have FFC and NFCR packages.

(ONP) On-Premises extension basic-1OPX Off-Premises extension

Supported by QPC192 only.



Administration

LD 10

OPS Off-Premises Station (default if CDEN is DD) xpe-20ONS On-Premises Station (default for all others)

(OVDD) Override Denied ffc-15OVDA Override Allowed

Must have Flexible Feature Codes (FFC) package 139

(PDN) Primary Directory Number pra-12LDN Listed Directory Number

The number used for the Calling Line Identification(CLID). 500/2500 sets have no display capability butprompt functions to transmit CLID information to setswith digit displays.

(PGND) Deny PAGENET access pagenet-22

PGNA Allow PAGENET accessPGND/A allowed if PAGENET package 307 is equipped.

(PRSD) Priority Call Pickup Station Denied povr-15PRSA Priority Call Pickup Station Allowed

(PUD) Call Pickup Denied grp-1PUA Call Pickup Allowed

Default changes to PUA if Ringing Number Pickup Group(RNPG) is defined. Call Pickup is not allowed ontelephones in group zero or RNPG = 0.

(RBDD) Redirection By Day Denied basic-24RBDA Redirection By Day Allowed

(RBHD) Redirection By Holiday Denied basic-24RBHA Redirection By Holiday Allowed

(RCC) Restricted from Receiving Collect Calls fca-10UCC Unrestricted from Receiving Collect Calls

(RMMD) Remote Monitoring of Messages Denied vmba-24RMMA Remote Monitoring of Messages AllowedRMMO Allow Remote Monitoring of Messages and to Override, if

it is being already monitored

(RTDD) Call Redirection by Time of day denied basic-22




LD 10

RTDA Call Redirection by Time of day allowedIf CLS = RTDD, AFD/AHNT/AEFD/AEHT will be removed,and ARTO will be reset to zero.

(SFD) Second Level CFNA Denied basic-10SFA Second Level CFNA Allowed

SFA requires FNA Class of Service.

(SHL) Short line Class of Service xops-20LOL Long line Class of Service (default if CLS = OPS)

Enter ALC Loss Plan Class of Service to be used fordetermining the Loss Plan Classification for this unit. Ifneither SHL or LOL is specified for a NEW unit, thenSHL will be set as the default.

(SMSD) Standalone Mail Server Denied samm-20SMSA Standalone Mail Server Allowed

(SMWD) Extended Message Waiting Indication Denied. vmba-24SMWA Extended Message Waiting Indication Allowed.

(SPKD) Speaker Denied ohol-15SPKA Speaker Allowed

Must have On-Hold on Loudspeaker (OHOL)package 196.

(SWD) Station-to-Station Call Waiting Denied basic-8SWA Station-to-Station Call Waiting Allowed

Enhances Call Waiting Allowed. Must have CLS = CWA.Must also have CLS = HTD, because hunting takesprecedence over Station-to-Station Call Waiting.

(TEND) Tenant Service Denied tens-7TENA Tenant Service Allowed

(THFD) Centrex Trunk Switch Hook Flash on this set denied thf-14THFA Centrex Trunk Switch Hook Flash on this set allowed

TSA Three-Party Service allowed mpo-20TSA is mutually exclusive with ASCA and XFA. If TSAis requested and XFA is currently set, then XFA will bechanged to XFD.

(TVD) Trunk Verification from station Denied tvs-10TVA Trunk Verification from station Allowed



Administration

LD 10

(UDI) Station is not restricted from receiving DID calls supp-10RDI Station is restricted from receiving DID calls

(ULAD) Set Based Administration User Access Denied adminset-21

ULAA Set Based Administration User Access Allowed

(USMD) Meridian 911 position Denied m911-19USMA Meridian 911 position Allowed

Must have Meridian 911 (M911) package 224

(USRD) User Selectable Call Redirection Denied uscr-19USRA User Selectable Call Redirection Allowed

(WTA) Warning Tone Allowed basic-1WTD Warning Tone Denied

(XFD) Call Transfer Denied basic-1XFA Call Transfer AllowedXFR Call Transfer Restricted

TSA is mutually exclusive with XFA. If TSA is requestedand XFA is currently set, then XFA will be changed toXFD. The most recently entered CLS overwrites the priorCLS of the same category. Note that one can specify XFRinstead of XFD.

(XHD) Exclusive Hold Denied dhld-4XHA Exclusive Hold Allowed

(XMWD) Extended Message Waiting indication Denied vmba-24XMWI Extended Message Waiting indication Allowed

(XRD) Ring Again Denied optf-1XRA Ring Again Allowed

Must have CLS= XFA. RANA may be activated ifOPT = RNA in LD 15. When OPT = RND in LD 15, all setswith CLS = XRA will be able to activate only Ring AgainBusy.




LD 10

CPND Calling Party Name Display cpnd-19NEW Add data blockCHG Change existing data blockOUT Remove existing data block

Must have CPND data block defined in LD 95.

CPND_LANG Calling Party Name Display Language cpnd-19(ROM) RomanKAT Katakana

CPND_LANG applies when FTR = CPND. CPND_LANGappears only when Multi-Language I/O (MLIO) package211 is equipped.

CRCS 0-7 Code Restriction Block nfcr-2

CUST xx Customer number associated with this set as definedin LD 15.

cust-1

DCLP 0-159 Dealer Conference Loop ohol-20DCLP input defines the conference loop assigned to theunit. The loop should be in the same group as the unit.

DELETE_VMB Delete Voice Mailbox vmba-19(YES) Remove the Voice Mailbox from the Meridian 1 and

Meridian MailNO Remove the Voice Mailbox from the Meridian 1

Prompted if REQ = OUT and TN has an associated VoiceMailbox. Allowed if the DN is either a single appearanceor a multiple appearance DN on a single TN.

DES d...d ODAS Station Designator odas-1Enter a 1-6 alphanumeric character representingan Office Data Administration System (ODAS) StationDesignator.



Administration

LD 10

DIG 0-2045 0-99 di-1Dial Intercom Group (DIG) number and Dial IntercomMember (DIM) numbers.

The value entered for the member number cannot beequal to the SPRE code. In the case of double-digitvalues, the first digit cannot be the same as the SPREcode. For example, if SPRE = 1, the member numbercannot be 10, 11...19.

Single line telephones assigned as Dial Intercom sets canonly make calls within their own dial intercom groups. NoDN can be assigned to them.

If any member in the group has a two digit membernumber, all members have a two digit number. Thesystem enters leading zeros.

Must have maximum number of Dial Intercom Groups(DGRP) defined in LD 15.

DISPLAY_FMT Display Format for CPND name cpnd-19(FIRST, LAST)

May be input as FIRSTTo view names as John Doe

LAST, FIRSTMay be input as LastTo view names as Doe John

DMC l s c

c

Digital Enhanced Cordless Telecommunications (DECT)Mobility Controller Location

Option 11C format

mc32-25

DN x..x yyyy Directory Number (x..x) and CLID table entry (yyyy)

The DN can be up to 4 digits, up to 7 digits with DirectoryNumber Expansion (DNXP) package 150. DN is notprompted for Option 11C model sets or if DIG is defined.

Range for CLID table entry is:[(0) - (value entered for SIZE prompt in LD 15 minus 1)]

basic-1




LD 10

If the new DN entered already exists, one of the followingmessages will be output when the TNB is updated:

• MIX (DN entered already appears on another set)• PVR (DN is a Private Line number)• HNT (DN exists and is defined as Hunting Allowed)• FNA (DN exists and has Forward No Answer)

Before the DN can be modified, the station DN must beremoved from all Group Hunt lists in which it is a member.

ISDN is not required for Calling Line Identification entry.

ECHG (NO) YES Easy Change. Prompted when REQ = CHG. basic-12This allows change to any prompt in this program withouttoggling through all the prompts.

ELKP x...x Electronic Lock Password ffc-14Prompted with the Flexible Feature Codes (FFC) package139. Password length is one to 15 digits, and is set inLD 15.

FCAR Forced Charge Account fca-1(NO) Must use Forced Charge AccountYES Restrict from using Forced Charge Account

Prompted if FCAF = YES in LD 15 and CLS = TLD, CUNor CTD. TLD is recommended.

FTR FTR Enter the feature name and related data.

Precede feature mnemonic with X to remove it from theallowed features for the telephone. Prompted with SpecialService for 2500 sets (SS25) package 18.

ss25-1

ACD x...x yyyy ism-16The ACD DN and the ACD position (POS ID)The ACD queue must be set in LD 23. ACD can be up to4 digits; up to 7 digits with Directory Number Expansion(DNXP) package 150.

An ACD entry is only allowed if you have already definedCLS = AGTA in the same pass through this overlay.



Administration

LD 10

ADL nn x..x Auto Dial ffc-15Auto Dial cannot be configured if Hot Line is defined.nn = number of digits, up to 31 maximum in Auto Dial DNx..x = Auto Dial DNAuto Dial is required for BNRA.Must have Flexible Feature Codes (FFC) package 139.

AEFD y...y Alternate External Flexible Call Forward DN, up to 13digits. Remove by setting CLS = RTDD or CFTD.Where yyyy = Alternate Redirection DN.

basic-22

AEHT y...y Alternate External Hunt DN, up to 13 digits. Remove bysetting CLS = RTDD or CFTD. Where yyyy = AlternateRedirection DN.

basic-22

AFD y...y Alternate Flexible Call Forward DN, up to 13 digits.Remove by setting CLS = RTDD. Where yyyy = AlternateRedirection DN.

basic-22

AHNT y...y Alternate Hunt DN, up to 13 digits. Remove by settingCLS = RTDD. Where yyyy = Alternate Redirection DN.

basic-22

CFW nn x...x ss25-1Call Forward all calls

Valid entries are any integer in the range of (4)-31.

Where: nn = maximum number of digits in the CFW DN; itmust be large enough to hold the customer Reply DN.Where: x...x = Call Forward DN

If the Enhanced System Access feature is configured,valid entries are 4, 8, 12, (16), 20, 24, 28, 31. Numbersbetween 4 and 31 are rounded up to the next validnumber.

If the Enhanced System Access feature is not configuredyou may input any integer in the range of (4)-23.




LD 10

CPND Call Party Name Display, name assignment allowed

Response required only if Background Terminal or PMSIis used to configure names. Response is not required ifCPND is programmed in LD 95.

cpnd-10

DCFW nn x...x supp-10Default Call Forward

Where: nn = maximum number of digits in the DCFW DN.

Valid entries for nn are: 4, 8, 12, 16, 20, 24, 28, 31.

Where: x...x = Default Call Forward DN.

EFD x...x External Flexible call forward DN (a Group Hunt pilot DNcan be entered)

basic-10

This is the DN to which external no answer calls arerouted when Class of Service is Call Forward by Call Typeallowed (CLS = CFTA). Must also have CLS = FNA.

EFD is only used if one of the following customer optionsare defined in LD 15:

• FNAD = FDN• FNAT = FDN• FNAL = FDN

Listed DNs, Departmental Listed DNs and prime DNs areaccepted as valid input. EFDs can be up to 13 digits.

EHT x...x External Hunt DN

This is the DN to which external busy calls Hunt whenClass of Service is Call Forward by Call Type allowed(CLS = CFTA). Must also have CLS = HTA.

basic-10

Listed DNs, Departmental Listed DNs and prime DNs areaccepted as valid input. A Group Hunt pilot DN can beentered with up to:

• 4 digits without DNXP package 150• 7 digits with DNXP package 150• 13 digits for Network Call Redirection



Administration

LD 10

FAXS x...x Facsimile server and command sequence

The command sequence includes the following:

• Wx = waiting time of 0 to 9 seconds• Cxxx = control command digits• Oxxxx = originating or designated fax DN• D = the called fax DN

faxs-18

For HiMail server, if the designated fax DN is 1234:

FTR FAXS W6 O1234 C#10* D C## W4, or

FTR FAXS W6 O1234 C#20* D C## W4

For Phi-Net server, if the designated fax DN is 1234:

FTR FAXS W4 C30 O1234 C*0 D C#

The facsimile server TNs must have Digitone (DTN) Classof Service and cannot have FNA, CWA, or FBA Class ofService, or FTR CFW feature.

Use the HUNT feature to define the DN of the next port onthe facsimile server.

FDN x...x Flexible Call Forward No Answer basic-1The DN cannot be an LDNA Group Hunt pilot DN can be entered of up to:

• 4 digits without DNXP package 150• 7 digits with DNXP package 150• 13 digits for Network Call Redirection

FDN is used for internal calls, if CLS is CFTA and FNA.FDN is used for all calls if CLS is CFTD and FNA.FDN requires that CLS = MWA or FNA.

FDN is only used if one or more of the following customeroptions are defined in LD 15:


HOT Option 11C model set hot-16Direct entry for Hotline model set. Automatic terminationDN is 8 digits.




LD 10

HOT D nn x...x hot-10Direct entry for one way Enhanced Hot Line. Where:

• nn = up to 31 digits maximum in Target DN• x...x = Terminating DN

CLS = EHTA and DIP or DTN

HOT D nn x...x yyyy hot-10Direct entry for two way Enhanced Hot Line. Where:

• nn = up to 31 digits maximum in Target DN• x...x = Terminating DN• yyyy = optional two way Hot Line DN. This DN can

be up to 4 digits, up to 7 digits with DirectoryNumber Expansion (DNXP) package 150.

CLS = EHTA and DIP or DTN.

HOT nn x..xFlexible Hot Line. Where: nn = up to 31 digits maximum inTarget DN and x..x = Terminating DN.Flexible Hot Line requires that CLS = MNL.

HOT L bbb One way list entry for Enhanced Hot Line hot-10Where: bbb = list entry position from Hot Line list in LD 18.The Hot Line list NCOS overrides the set NCOS.

Enhanced Hot Line requires CLS = EHTA, LLCN, PHTDand DIP or DTN. To remove Hot Line DN, change CLSEHTA to EHTD.

Hot Line DNs can be programmed with * as operands onlyif OPAO is enabled.

HOT L bbb x...x hot-10Two way list entry for Enhanced Hot Line. Where:

• bbb = list entry position• xxxx = optional two way Hot Line DN. This DN can

be up to 4 digits, up to 7 digits with DirectoryNumber Expansion (DNXP) package 150.

Enhanced Hot Line requires CLS = EHTA, LLCN, PHTDand DIP or DTN. To remove Hot Line DN, change CLSEHTA to EHTD.

Hot Line DNs can be programmed with * as operands onlyif OPAO is enabled.



Administration

LD 10

ICF x...x icf-19Internal Call Forward and Forward DN length.

Valid entries for x...x are: any integer in the range of(4)-31.

ISP 1-(75)-255 basic-21Enable hook flash disconnect supervision with flash timerin 10 milliseconds units. If the numeric parameter is notentered and the saved value is null, it is defaulted to 75(750 ms). Otherwise, it does not change.

OSP (1) Enable battery reversal answer and disconnectsupervision for outgoing calls with absolute and assumedanswer indication.

basic-21

OSP 2 Enable battery reversal answer and disconnectsupervision for outgoing calls with absolute answerindication only.

If the numeric parameter is not entered and the savedvalue is null, it is defaulted to 1. Otherwise, it does notchange.

PHD Permanent Hold. Allowed with CLS = XFA. basic-1

RDL nn Stored Number Redial

Where: nn = DN length 4, 8, 12, (16), 24, 28, 31. Numbersbetween 5 and 30 are rounded up to the next validnumber. Allowed with CLS = XFA.

snr-3

SCC 0-8190 optf-1Speed Call Controller list numberThe speed call list must be defined in LD 18.

SCU 0-8190 optf-1Speed Call User list numberThe speed call list must be defined in LD 18.

SSU 0-4095 ssc-2System Speed call User list numberThe speed call list must be defined in LD 18.

XISP Disable hook flash disconnect supervision




LD 10

XOSP Disable battery reversal answer and disconnectsupervision

HDID (0)-9 Off-Hook Alarm Security Half Disconnect Index defined inLD 15

basic-24

HMDN x..x Home Directory NumberSets the DN as a valid MCDN network DN

msmn-32

HUNT x...x Hunt DN of the next station in the Hunt chain

A Group Hunt pilot DN can be entered of up to:

• 4 digits without DNXP package 150• 13 digits with DNXP package 150

Precede with X to remove.

With Call Forward and Hunt by Call Type, this is the HuntDN for:

• internal calls if CLS = CFTA, or• all busy calls if CLS = CFTD

A Control Directory Number (CDN) can be defined as aHunt DN for both physical and phantom 500/2500 sets.When a CDN is configured in this way, a call which comesto a busy DN can be Hunting or Call Forward Busy to aCDN.

basic-1

IAPG (0)-15 Meridian Link Unsolicited Status Message (USM) group aml-16Assign Associate (AST) telephones to an USM groupdefined in LD 15. These groups determine which statusmessages are sent to the host computer for an ASTtelephone. The default Group 0 sends no messages,while Group 1 sends all messages.

aml-16

ICT 0-<NIPN> Intercept Computer Terminal or Printer Number icp-16The Number of Intercept Positions (NIPN) is definedin LD 15.

INDX 0-509 DECT Mobility Controller indexMaps hand set to Virtual TN

mc32-25

ITEM aaaa yyy Change any prompt basic-12Respond with the desired program mnemonic (aaaa) andits new value (yyy). ITEM is reprompted until only acarriage return <cr> is entered.



Administration

LD 10

KEEP_MSGS Keep Messages vmba-19(NO) YES Preserve Meridian Mail messages and current password

LDN (NO) Departmental Listed Directory Number is not activatedfor this set

dldn-5

0-5 Departmental Listed Directory Number (LDN) as definedin LD 15

LNRS 4-(16)-31 Last Number Redial Size

Enter the maximum number of digits that can be stored.Valid entries are 4, 8, 12, (16), 24, 28, 31. Invalid entriesare rounded up to the next valid entry. Prompted ifCLS = LNA.

lnr-8

MARP (NO) YES Multiple Appearance Redirection Prime basic-18Use TN as the Multiple Appearance DN RedirectionPrime. The MARP prompt, or MARP information, isgiven only when assigning a DN.

MAUT (NO) YES Modify assigned authorization codes for this telephone ssau-19Prompted with Station Specific Authorization Codes(SSAU) package 229 and CLS = AUTR.

MLWU_LANG Language choice for Automatic Wake Up service.Prompted with Multi-Language Wake Up (MLWU)package 206. This entry defines the language presentedfor the Automatic Wake Up recorded announcement(RAN) for language 0 through 5 as follows:

mlwu-19

(0) See RAN1/RAN2 in LD 151 See LA11/LA12 in LD 152 See LA21/LA22 in LD 153 See LA31/LA32 in LD 154 See LA41/LA42 in LD 155 See LA51/LA52 in LD 15X Remove entry

MODL 1-127 Model number basic-16Prompted for Option 11C model sets.

MWUN (16) 32 Maximum number of Wireless Units mc32-24Standard line card = 16Octal line card = 32




LD 10

NAME Calling Party Name Display Name cpnd-21aaaa,bbbb First name comma Last name.

For example, John Doe is entered as John,Doe. Thefirst single comma is treated as the delimiter. Up to 27characters (including the comma) may be input. The lastoccurrence of the first comma group serves as the namedelimiter and is translated into a space between the firstand last name.

aaaa When the delimiter is omitted, the input is stored as a firstname.

aaaa, When the delimiter follows the input, the input is stored asthe first name.

,bbbb When the delimiter precedes the input, the input is storedas a last name.

NCOS Network Class of Service group number ncos-2(0)-3 CDP(0)-7 BARS or NFCR(0)-15 NARS(0)-99 Network Class of Service group number

OHID (0)-9 Off-Hook Alarm Security DN index

Enter the index number 0-9 of the DN defined by LD 15prompt ODNx. When a dial tone or interdigit timeoutoccurs on a set with Alarm Security Allowed (ASCA)Class of Service, the set is intercepted to a predefinedDN.

basic-18

PLEV 0-(2)-7 Priority Level

Where: 2 = set can override sets of level 1 and 2, and canbe overridden by sets of level 2-7. Prompted with PriorityOverride/ Forced Camp-On (POVR) package 186 orEnhanced DPNSS1 Services (DPNSS_ES) package 288.

povr-20

POS xxxx ACD position ID. Prompted when SFMT = AUTO,TNDN, TN or DN.

basic-12



Administration

LD 10

PRI (1)-48 Priority level for ACD Agent.The agent with the lowest number assigned has thehighest priority and is the first ACD agent to receive calls.(Priority 1 has the highest priority level)

PRI is prompted if Automatic Call Distribution, PriorityAgent package 116 is equipped and CLS = AGTA.

pagt-16

RCO (0)-2 Ringing cycle option for Call Forward No Answer uscr-19Prompted when CLS = FNA or MWA (or both).

REQ: Request basic-1

? To get a list of valid responses

CHG Change existing data block

CDCS Convert Digital Communications Set

Note: The CDCS command can also be used on MCMO typetelephones

mc32-25

CPY n Copy or create 1 to 32 new station data block or blocksautomatically from the specified station data block.Not valid for Option11 models.

END Exit Overlay program

MOV Move data block from one TN to another.

MOV command can be used to move analogue "IPE"telephones from one loop, shelf, card, unit to another lscuwith the following restrictions (includes moves acrossSuperloops):

-ACD sets must not be moved. Remove (out) data andre-enter at destination.

-Telephones with mixed directory numbers can only bemoved to a TN on the same loop; unless the promptMLDN = Yes in LD 17.

-Cannot be used for Option 11C model sets

MOV command can be used to move analogue "EPE"telephones from one unit or card to another, but does notsupport moving these phones across shelves or loops.

basic-25.4

NEW X Add new data block or blocks




LD 10

Follow NEW with a value of 1-255 to create that numberof consecutive telephone data block or blocks.

OUT X Remove data block or blocksFollow OUT with a value of 1-255 to remove that numberof consecutive telephones.

The following is a list of valid responses. For furtherinformation, consult the appropriate Overlay program.

LD 32: CDSP CMIN CONV CPWD DISC DISI DISLDISN DISS DISU DSCT DSPS DSXP ENCT ENLCENLG ENLL ENLN ENLS ENLU ENPS ENXP IDCIDCS IDU LBSY LDIS LIDL LMNT PBXT SDLCSTAT SUPL TRK XNTT XPCT XPEC

LD 20: LTN LUC LUDU LUU LUVU PRT

LD 10: CHG CPY MOV NEW OUT

RNPG (0)-255 Ringing Number Pickup Group grp-1(0)-4095 Ringing Number Pickup Group with Capacity Expansion grp-1

To remove a telephone from a group, enter 0 in responseto the RNPG prompt.

SCI (0)-7 Station Category Indication priority level sci-7The Station Category number 1 to 7 must be defined asattendant console Incoming Call Indicator in LD 15 promptICI = CA1-CA7.

SCPW xxxx Station Control Password

The Station Control password is used for the ElectronicLock and Remote Call Forward features. This entry mustequal the Station Control Password Length (SCPL) asdefined in LD 15.

Not prompted if SCPL = 0. See Flexible Feature Codes inthe Features and Services (553-3001-306).

ffc-15

SECOND_DN vmba-19x...x Second Directory Number sharing the Voice Mailbox. This

number can be up to 4 digits, up to 7 digits with DirectoryNumber Expansion (DNXP) package 150.

X Enter the letter “X” to delete the second directory number



Administration

LD 10

SFDN xxxx Secretarial Forwarding DN of secretary set ftcsf-15SFDN is prompted if SFLT = BOSS.

SFLT Secretarial Filtering ftcsf-15(NO) Assign no designation to telephone setBOSS Designate telephone set as a Boss setSEC Designate telephone set as a Secretary set

(NO), SEC and <cr> takes you to the next prompt.SFLT is prompted with Boss Secretary Filtering (FTCSF)package 198.

SFMT Select Format for the copy command

The DN may be up to 4 digits, up to 7 digits with DirectoryNumber Expansion (DNXP) package 150. The POSprompt appears if CLS = AGTA.

basic-12

TNDN Manual selection of TNs, DNs and ACD position IDs forACD telephones. TN, DN and POS are prompted -n-times as defined by the CPY command.

TN The new DNs and ACD position IDs for ACD telephonesare provided by the system. You are prompted for thestarting DN, ACD position ID and each TN. TN isprompted n times as defined in the CPY command.

DN The new TNs are provided by the system. You areprompted for the starting TN and each DN and ACDposition ID for ACD telephones. DN and/or POS areprompted n times as defined in the CPY command.

AUTO The new TNs, DNs and ACD position ID for ACDtelephones are provided by the system. You are promptedfor the starting TN, DN and ACD position ID.

SGRP (0)-999 Scheduled Access Restriction Group Number sar-15Prompted with Schedule Access Restrictions (SAR)package 162. The group must be defined in LD 88.




LD 10

SPID x...x Supervisor Position ID

This input assigns an agent to a supervisor when agentlamps are not assigned on the supervisor telephone.

This number can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.However, ISDN applications can accept up to 13 digits.

Prompted for ACD packages B, C and D whenCLS = AGTA.

acdb-1

SPWD xxxx Secure Data Password ssau-19Prompted if the password is defined in LD 15. If thepassword is not entered, the security codes will not printwhen PRT is requested.

TEN 1-51 Multi-Tenant Number tens-7Enter the Multi-Tenant number for this telephone.Prompted with Multiple-Tenant Service (TENS)package 86 and Tenant Service enabled.

TGAR 0-(1)-31 Trunk Group Access RestrictionThe default of (1) automatically blocks direct access.

basic-1

THIRD_DN Third DN sharing the Voice Mailbox vmba-19x...x Third Directory Number. This number can be up to 4

digits, up to 7 digits with Directory Number Expansion(DNXP) package 150.

X Deletes the third directory number



Administration

LD 10

TIMP Termination Impedance for XOPS unit basic-20(600) 600 ohms900 900 ohms

The following combinations of TIMP/BIMP are valid:

• 600/600• 900/900• 600/3COM• 900/3COM• 600/3CM2• 900/3CM2

These are equivalent to the TIMP/BIMP prompts in LD 14for the EXUT card. TIMP is prompted if the specified TNwill be configured on an XOPS card (DD card on asuperloop). If the response to TIMP uniquely describesthe TIMP/BIMP combination, then BIMP is not prompted.

TN TN Terminal NumberThe TN defines the location of the telephone set.

basic-1

l s c u

TN appears when REQ = NEW, CHG, MOV or OUT.

Large system TN format: l s c u = loop, shelf, card, unit

Where l =

• 0-159: loops, superloops which are multiples of 4,starting with superloop 0

• 0-255: loops, Option 81C with Fiber Network Fabric fnf-25

Where s =

• 0-3: PE shelves on loops defined TERM in LD 17• 0-1: PE shelves on loops defined TERD in LD 17

and superloops• 0: PE shelf on loops defined TERQ in LD 17

Where c =

• 1-10: PE cards of dual and enhanced loops• 0-15: IPE cards of superloops

Where u =

• 0-3: single density units• 0-7: double density units• 0-15: quad density units




LD 10

c u Small system format: c u = card, unit

• c = 1-50• u = 0-15

basic-16

TOTN To Terminal Number. Prompted when REQ = MOV. basic-1l s c u Large system TN format: l s c u = loop, shelf, card, unitc u Small system TN format

TOTN is not prompted for Option 11C model sets.

basic-16

TYPE: TYPE: Type of data block. basic-20

? To get a list of valid responses

500 500/2500 telephone set data block500 M 500/2500 Model telephone set data block for Option 11C

CARD 500/2500 card block for Automatic Set Relocation (ASR)

CARDSLT Single-line telephone line card

DCS Digital Cordless Set mc32-25

OOSSLT Out-of-Service Single Line Terminal unit

VMB NEW Add Voice Mailbox vmba-19CHG Change Voice MailboxOUT Remove Voice Mailbox

VMB_COS vmba-190-127 Voice Mailbox Class of Service

VSIT (NO) YES Visiting DECT setDetermines the difference between a local handset and avisiting handset.

msmn-32

WRLS (NO) YES TN corresponds to a portable personal telephone. mcmo-20Must have Meridian 1 Companion Option (MCMO)package 240.

Note: Additional units configured on either the MCMO or DECTcard requires identical entries for WRLS, WTYP and MWUNprompts.

WTYP (MCMO) Meridian Companion Mobility Option mcmo-23DECT Digital Enhanced Cordless Telephone



Administration

LD 10

XLST (0)-254 Pretranslation group associated with this station pxlt-10If the user wants to use a 16-button DTMF ABCD set as acall forward destination station to deactivate the callforward all calls function, then XLST must be set equal tothe table number defined in LD 18.

XPLN xx Expected name length (this value should be set to asufficient length for current and future names for that DN)

When REQ=NEW, the XPLN prompt defines themaximum name length for that particular DN or DIG. TheXPLN for a DN cannot be changed without deleting thatname entry.

XPLN must range from the actual length of the namestring to MXLN, or defaults to DFLN.

cpnd-19



Administration

LD 11



ADAY (0)-3 Alternate Days as defined in LD 15Prompted if CLS = RBDA

basic-24

ADCP All-Digital Connection Prefix. ADCP appears whenDTYP = ODS or IOS.

adm-5

(NO) Do not enable All-Digital Connection Prefix

YES Enable All-Digital Connection Prefix

AEFD Alternate External Flexible Call Forward DN.Remove by setting CLS = RTDD or CFTD.

basic-22

x...x Alternate Redirection DN (up to 13 digits)

AEHT Alternate External Hunt DN. Remove by settingCLS = RTDD or CFTD.

basic-22


AFD Alternate Flexible Call Forward DN. Remove bysetting CLS = RTDD.

basic-22


AHNT Alternate Hunt DN. Remove by setting CLS = RTDD. basic-22


AHOL (0)-3 Alternate Redirection Holiday as defined in LD 15Prompted if CLS = RBHA

basic-24



LD 11

ANIE (0)-n ANI Entry: it is of (0)-N where N=S_SIZE in customerdata block.

If ANIE=0, no entry is associated with the set. Theold mechanism will be used for building the ANImessage.

If ANIE is of 1-N:

• If ANIC = YES for the outgoing CIS routewhere the call takes place, then thecomponents of the ANI message areretrieved from the ANI entry in CustomerData Block, if configured.

• If the given ANI Entry is not configured, or ifANIC = NO for the outgoing CIS route wherethe call takes place, then the old mechanismis used for building the ANI message.

cist-24

AOM 0-2 Number of Add-on Modules. AOM appears ifTYPE = M2216 and M2616.

arie-14

ARTO (0)-3 Alternate Redirection Time Option for callredirection, defined in the customer data block.ARTO is prompted if CLS = RTDA.

basic-22

AST xx yy Associate Set Assignment for Meridian Linkapplications

A maximum of two DN keys, xx and yy, can becontrolled by the host computer. Precede with X todelete.

iap3p-12

AUT (ON) Enable Auto-Answer arie-14

OFF Do not enable Auto-Answer

AUTB (ON) Auto Baud rate enabled dac-16

OFF Auto Baud rate disabled

AUTB is prompted if TYPE = R232 or R422 and ifHOT = OFF.



Administration

LD 11

AUTH n xxxx Authorization code. Where:

• n = the number of the assigned authorizationcode (1-6)

• xxxx = assigned authorization code (Anyauthorization code assigned in LD 88 is valid).

AUTH appears when CLS = Authorization CodeRequired (AUTR).

ssau-19

BAUD Baud rate mcu/arie-19

0-(7)-8 Baud rate index for the data port for data port onM2006, M2008, M2216 and M2616 telephones andData Access Card.

0-(7)-10 Baud rate index for the data port for M3901,M3902,M3903, M3904, and M3905 telephones.

basic-24

The following values apply to:

• MPDA-1• MCA with DTAO = MPDA and TRAN = ASYN• MCA with DTAO = MCA• TYPE = MCU and TRAN = ASYN

Where: 0 = 110, 1 = 150, 2 = 300, 3 = 600, 4 = 1200,5 = 2400, 6 = 4800, (7) = 9600, 8 = 19,200,9=28,800, and 10=33,600.

0-(11)-12 The following values apply to:

• MCA with DTAO = MPDA, with MCAhardware

• TRAN = SYN, MCA with TRAN = SYN• MCA with DTAO = MCA

Where: 0 = 1200, 1 = 2400, 2 = 3600, 3 = 4800,4 = 7200, 5 = 9600, 6 = 14,400, 7 = 19,200,8 = 38,400, 9 = 40,800, 10 = 48,000, (11) = 56,000,and 12 = 64,000.

With DAC, BAUD is only prompted if AUTB (AutoBaud Rate) = OFF.




LD 11

CAC_CIS 0-(3)-9 CIS ANI Category Access Code cist-24

CAC_MFC (0)-10 MFC CNI Category Access Code cist-24

CDEN SD Single Card Density basic-7

DD Double Card Density

4D Quadruple Card Density

8D Octal Card Density

CDEN defaults to the density of the network loop.CDEN is not prompted for Option 11C model sets orsuperloops.

CFTN Copy From Terminal Number basic-12

l s c u General TN format

For Meridian: l s c u = loop, shelf, card, unit

c u Option 11C format

Use this TN as a template for new sets. ACDsupervisory sets cannot be copied. Associate set(AST) assignments are not copied to the new sets.

With the introduction of Phantom TNs, the systemchecks to be sure that TNs are not moved or copiedfrom phantom TNs to non-Phantom TNs or visaversa.

CFTN appears if REQ = CPY.

CLK (OFF) Clock off arie-14

ON Clock on

CLS CLS Class of Service options basic-1

The following CLS assignments determine thecalling options and features available to thetelephone. Defaults are shown in parentheses. Entereach non-default option required, separated by aspace.



Administration

LD 11

Access Restrictions basic-1

(CTD)UNRCUNTLDSREFREFR1FR2

Conditionally Toll Denied (default)UnrestrictedConditionally Unrestricted.Toll Denied.Semi-Restricted.Fully Restricted.Fully Restricted 1.Fully Restricted 2.

(AAD) Automatic Answerback Denied aab-10

AAA Automatic Answerback Allowed

Automatic Answerback can be used on M2112,M2317, M2616, M3000 and SL-1 telephones withhandsfree capability. A special hardware kit isrequired for SL-1 sets and Companion 4speakerphones.

Automatic Answerback must have CLS = HFA forM2616 telephones. CLS AAA or AAK keys are notallowed for M2317 TNs.

(ABDD) Abandoned call record and time to answer Denied fcdr-18

ABDA Abandoned call record and time to answer Allowed

Digit Display ddsp-1

ADD Automatic Digit Display, default for M2008, M2216,M2317, M2616, M3000, M3902, M3903, M3904, andM3905

DDS Delay Display, display activates after call isanswered

NDD No Digit Display, default for SL-1, M2006, M2009,M2112, M2018




LD 11

TDD Tandem Digit Display. Automatic set display feature,TDD Class of Service is applicable to all Meridian 1proprietary sets except for the M2006 which does nothave display capability.

Note: Manufacturer discontinued sets, such as the M2317and the SL1, can be configured with TDD Class of Servicehowever, may not have full functionality of the AutomaticSet Display feature.

(AGN) ACD Agent

SPV ACD Supervisor

(AGRD) Agent Greeting Denied fxs-25

AGRA Agent Greeting Allowed

(AHD) Automatic Hold Denied supp-10

AHA Automatic Hold Allowed

(ARHD) Audible Reminder of Held Call Denied basic-14

ARHA Audible Reminder of Held Call Allowed

(ASCD) Alarm Security Denied ohas-18

ASCA Alarm Security Allowed

(AUTU) Unrestricted Authorization code Class of Service ssau-19

AUTD Denied Authorization code Class of Service

AUTR Restricted Authorization code Class of Service

When the CLS is changed from AUTR to AUTU orAUTD, all previous telephone authorization codeinformation is removed. This Class of Service is validonly when Station Specific Authorization Codes(SSAU) package 229 is equipped.

(BFED) Boss Secretary Feature Enhancement Denied ffcsf-24

BFEA Boss Secretary Feature Enhancement Allowed

(BUZZ) Buzz basic-24



Administration

LD 11

RNGI Apply ringing when idle but off hook

RNGB Apply ringing when idle but off hook or busy on theother line

(CCBD) Collect Call Blocking Denied (permits a set to acceptcollect calls)

ccb-21

CCBA Collect Call Blocking Allowed (prevents a set fromaccepting collect calls

Collect Call Blocking (CCB) package 290 is required.

(CCSD) Controlled Class of Service Denied ccos-7

CCSA Controlled Class of Service Allowed

CCSA is required for the Electronic Lock feature.Must have Controlled Class of Service (CCOS)package 81.

(CDCA) Conferee Display Count Allowed. basic-23

CDCD Conferee Display Count Denied.

(CDMD) CDMD denies external station activity records to begenerated for the set

emct-20

CDMA CDMA allows external station activity records to begenerated for the set

(CFHD) Call Forward Hunt Override Denied cfho-20

CFHA Call Forward Hunt Override Allowed

(CFTD)CFTA

Call Forward by Call Type Denied/AllowedIf response is CFTA, you must also designate HTA,FNA or both.

optf-10




LD 11

(CFXD) Call Forward All Calls to External DN Denied optf-19

CFXA Call Forward All Calls to External DN Allowed

Examples of external DNs are:

• Route Access Code• ESN Access Code• CDP Distant Steering Code

When denied, a call can only be forwarded to thefollowing internal DNs:

• Single or multi-line telephone• Attendant DN or CAS local attendant DN• Listed DN as defined in LD 15• Message Center DN where MWC = YES

(CLBD) Deactivate Calling Party Number and Name per-lineblocking

cpp-21

CLBA Activate Calling Party Number and Name per-lineblocking

The user may still request CPP by dialing the CPPcode.

(CLTD) Network Call Trace from this telephone Denied pra-17

CLTA Network Call Trace from this telephone Allowed

(CMSD) Command and Status link Denied csl-8

CMSA Command and Status link Allowed

CMSA is not supported by M2009, M2018, M2112,M2317, and M3000.

(CNDD) Call Party Name Display Denied cpnd-10

CNDA Call Party Name Display Allowed

CNDA allows user names to be displayed on thetelephone’s digit display.

(CNID) Call Number Information Denied bgd-10

CNIA Call Number Information Allowed



Administration

LD 11

(CNTD) Network ACD Countdown Denied nacd-15

CNTA Network ACD Countdown Allowed

Only allowed on ACD agent telephones.

(CPFA) Forced Camp-On from another set Allowed scmp-15

CPFD Forced Camp-On from another set Denied

(CPTA) Forced Camp-On to another set Allowed. CPTA isthe default for VCE TNs.

scmp-15

CPTD Forced Camp-On to another set Denied

(CRPD) Corporate Directory Denied arie-25

CRPA Corporate Directory Allowed

Only applies for M3903 and M3904 units.

(DAPA) Display Access Prefix Allowed isdn-24

DAPD Display Access Prefix Denied

(DDGA) DN Display on other set Allowed dpd-21

DDGD DN Display on other set Denied

(DDV) Data Port Verification Denied amp-5

ADV Data Port Verification Allowed

(DELD) Dealer Denied ohol-20

DELA Dealer Allowed

Must have On-Hold On Loudspeaker (OHOL)package 196.

(DNAA) DN of the key that makes the call used in ANImessages.

cist-21

DNAD Outgoing CDTI2/CSDTI2 route ANDN used as DN inANI messages

Must have Commonwealth of Independent StatesTrunk Interface (CIST) package 221.




LD 11

(DNDD) Dialed Name Display Denied cpnd-13

DNDA Dialed Name Display Allowed

DNDA allows the display of the originally dialed DN’snames on redirected calls. Name display applies toM2317, M3000 or Meridian Modular telephones withdisplays.

Must have Calling Party Name Display (CPND)package 95. Must also have CLS = CNDA. CLS isnot DTA.

(DNDY) Diversion Notification with called party’s number andname when available.

qsig ss-23

DNDN Diversion Notification without called party’s numberand name notification.

(DNO3) Diversion Notification Option with diverted-to party’snumber and name when available.

qsig ss-23

DNO1 Diversion Notification Option without notification.

DNO2 Diversion Notification Option without diverted-toparty’s number and name.

(DOS) ACD Supervisory Set Denied observation of othersupervisory sets

acdb-1

AOS ACD Supervisory Set Allowed observation of othersupervisory sets

Must have CLS = SPV.

(DPUD) DN Pickup Denied dcp-12

DPUA DN Pickup Allowed

(DRDD) Distinctive Ringing by Directory Number Denied. edrg-24

DRDA Distinctive Ringing by Directory Number Allowed.



Administration

LD 11

Digital telephone distinctive ringing drng-7

(DRG1) High fast tone, frequency 667 Hz/500 Hz,warble rate 10.4 Hz

DRG2 High slow tone, frequency 667 Hz/ 500 Hz,warble rate 2.6 Hz

DRG3 Low fast tone, frequency 333 Hz/ 250 Hz,warble rate 10.4 Hz

DRG4 Low slow tone, frequency 333 Hz/ 250 Hz,warble rate 2.6 Hz

DRG3 and DRG4 distinctive ringing for M2006 andM2008 telephones are different.

DRG3 Low fast tone, frequency 1600/ 2000 Hz,warble rate 10.0 Hz

DRG4 Low slow tone, frequency 1600/ 2000 Hz,warble rate 2.5 Hz

(DSX) Data Service access or IS Server TN Denied cls-8

DSI Data Service access or IS Server TN Allowed

CLS is automatically set to DTA.

(ELD)ELA

Erase lists DeniedErase lists Allowed

basic-25.4

(EXR0) Executive Distinctive Ringing Off (0) edrg-16

EXR1 Executive Distinctive Ringing Tone 1




The digit indicates which of the four distinctiveringing tones and cadences defined in LD 56 is to beused. Executive Distinctive Ringing (EDRG)package 185 is required.Must have (DRDD) class of service




LD 11

(FBD) Call Forward Busy Denied basic-1

FBA Call Forward Busy Allowed

This feature sends DID calls encountering a busycondition to the attendant. Call Forward Busy shouldhave Hunting and Call Waiting denied, CLS = HTDand CWD, since Hunting and Call Waiting takeprecedence over FBA.

(FDSD)FDSA

Force Disconnect DeniedForce Disconnect Allowed

ponw-25.4

(FICD) Forward Intercom Calls Denied basic-21

FICA Forward Intercom Calls Allowed

(FITD) Flexible Incoming Tones Denied basic-14

FITA Flexible Incoming Tones Allowed

For SL-1 sets OPT must be SBA in LD 15. For Digitalsets OPT must be DBA in LD 15.

(FLXD) Flexible voice/data Denied basic-22

FLXA Flexible voice/data Allowed

FLXA is only allowed for Aries sets.

By entering FLXA, you may configure dynamic voice/data TNs by assigning VCE to the upper TN (unit 16-31) and DTA to the lower TN (unit 0-15). You alsohave the option of designating a SCR key as DTM(data mode).

Warning: If connecting the Aries set only to the TCMloop, this option should not be specified. Externalequipment which can use this capability should beconnected.

Warning: When changing from CLS DTA to CLSVCE, CLS WTA should also be assigned to avoidconflict with CLS CPTA. CLS CPTA is the default forVCE TNs.

(FND) Call Forward No Answer Denied basic-1



Administration

LD 11

FNA Call Forward No Answer Allowed

(FRN) French language display dlt2-12

ENG English language display

For M2317 alphanumeric display sets.

(FTTC) Flexible Trunk to Trunk Connections Conditionalallows trunk to trunk connections for supervisedConference.

basic-23

FTTR Flexible Trunk to Trunk Connections Restricteddenies trunk to trunk connections for Transfer andunsupervised Conference.

FTTU Flexible Trunk to Trunk Connections Unrestrictedallows trunk to trunk connections for bothConference and Transfer.

FXSP Flexible Services Port fxs-25

(GPUD) Group Pickup Denied dcp-12

GPUA Group Pickup Allowed

Group Pickup is not allowed on telephones in groupzero, RNPG = 0.

(GRLD) Group Listening Denied basic-24

GRLA Group Listening Allowed

For M3902, M3903, M3904 Taurus sets.

(HBTD) Hunt By Call Type Denied basic-10

HBTA Hunt By Call Type Allowed

(HFD) Digital Telephone Handsfree Denied arie-14

HFA Digital Telephone Handsfree Allowed

Only available for M2616 telephones. Handsfreecapability on all other telephones is a function of thehardware and does not require HFA Class of Servicein order to operate.




LD 11

(HSPD) Hospitality Denied, used for Hospitality Management hvs-16

HSPD is for administration sets.

HSPA Hospitality Allowed, used for HospitalityManagement

HSPA is for room sets. For HSPA, you must alsoenter CLS = CCSA and CLS = MRA. HSPA CLScannot be entered for a set with transfer orconference capability. Prime DN must be singleappearance, single call ringing or non-ringing.

(HSTD) Host Terminal Denied arie-25

HSTA Host Terminal Allowed

(HTD) Hunting Denied basic-1

HTA Hunting Allowed

(ICDD) Internal Call Detail Recording Denied icdr-10

ICDA Internal Call Detail Recording Allowed

(IMD) Integrated Messaging Service Attendant Denied ims-2

IMA Integrated Messaging Service Attendant Allowed

(IPND) Intercept Position Denied icp-10

IPNA Intercept Position Allowed

(IRD) Incoming Ringing Line Preference Denied lsel-4

IRA Incoming Ringing Line Preference Allowed

(LLCN) Line Load Control off llc-10

LLC1 Class 1

LLC2 Class 2

LLC3 Class 3

(LMPN) Red LED on Meridian Modular Telephone reflectsthe status of the mailbox associated with the PDN

vmba-24



Administration

LD 11

LMPX Red LED on Meridian Modular Telephone reflectsthe status of the mailbox associated with the PDNand non-PDNs

(LND) Last Number Redial Denied lnr-8

LNA Last Number Redial Allowed

Must have OPT = LRA in LD 15.

(LPR) Low Priority Station povr-16

HPR High Priority Station

High Priority will place this set or trunk at the top ofthe dial tone queue.

(LVXD) LOGIVOX Class of Service Denied supp-10

LVXA LOGIVOX Class of Service Allowed

MCBY Set linked to a MICB line card. basic-25

MCBN Set linked to a non-MICB line card.

(MCTD) Malicious Call Trace Denied mct-10

MCTA Malicious Call Trace Allowed

The MCT key must be removed before changingMCTA to MCTD. MCT is applied on a TN basis.

(MIND) Message Interrupt Denied mr-15

MINA Message Interrupt Allowed

(MMD) Multimedia (Denied) ngen-24

MMA Multimedia Allowed

(MOAD) Mute on Answer Denied fxs-25

MOAA Mute on Answer Allowed

(MRD) Message Registration Denied mr-10

MRA Message Registration Allowed




LD 11

(MSID) Make Set Busy Improvement Denied msb-24

MSIA Make Set Busy Improvement Allowed

(MTD) Maintenance Telephone Denied basic-1

MTA Maintenance Telephone Allowed

(MWD) Message Waiting Denied mwc-1

MWA Message Waiting Allowed

If CLS = MWA and there is no Message Waiting Key(MWK) defined, then the red Message Waiting LEDlights to indicate Message Waiting notification.

(NAID) No Answer Indication Denied basic-21

NAIA No Answer Indication Allowed

(NAMA) Name Display on other set Allowed dpd-21

NAMD Name Display on other set Denied

(NOVD)NOVA

Network Override/Breakin DeniedNetwork Override/Breakin Allowed

pomw-25.4

(NID) Non-ringing Incoming Line Preference Denied lsel-4

NIA Non-ringing Incoming Line Preference Allowed

(NRCD) Night Restriction for Forced Campon Denied povr-16

NRCA Night Restriction for Forced Campon Allowed

If Night Restriction is allowed, then Forced Camponfor this set is allowed during Night Service only.

(NROD) Night Restriction for Priority Override Denied povr-16

NROA Night Restriction for Priority Override Allowed

If Night Restriction is allowed then Priority Overridefor this set is allowed during Night Service only.



Administration

LD 11

(NRWD) Night Restriction for Call Waiting Denied povr-16

NRWA Night Restriction for Call Waiting Allowed

If Night Restriction is allowed Call Waiting for this setis permitted during Night Service only.

(OCBD) Outgoing Call Barring Denied ccb-21

OCBA Outgoing Call Barring Allowed

Flexible Feature Codes (FFC) package 139 andNew Flexible Code Restriction (NFCR) package 49are required.

(OLD) Outgoing Line Preference Denied lsel-4

OLA Outgoing Line Preference Allowed

(ONDD) One Number Delivery Denied for a portable basic-22

ONDA One Number Delivery Allowed for a portable

(PDN) Primary Directory Number pra-12

LDN Listed Directory Number Index as defined in LD 15

This is the number used for Calling Line Identificationor CLID.

(PGND) Deny PAGENET access pagenet-22

PGNA Allow PAGENET access

PGND/A allowed if PAGENET package 307 isequipped.

(POD) Privacy Override Denied basic-5

POA Privacy Override Allowed

The Privacy Optional feature is used with multipleappearance DNs.

(PRSD) Priority Call Pickup Denied povr-15

PRSA Priority Call Pickup Allowed




LD 11

(PUD) Call Pickup Denied grp-1

PUA Call Pickup Allowed

Default changes to PUA if Ringing Number PickupGroup (RNPG) is defined. Call Pickup is not allowedon telephones in group zero or RNPG = 0.

(RBDD) Redirection By Day Denied basic-24

RBDA Redirection By Day Allowed

(RCC) Restricted from Receiving Collect Calls fca-10

UCC Unrestricted from Receiving Collect Calls

(RBHD) Redirection By Holiday Denied basic-24

RBHA Redirection By Holiday Allowed

(RCBD) Recall to Boss Denied bfs-24

RCBA Recall to Boss Allowed

(RDLA) Automatic Redial Allowed ardl-22

RDLD Automatic Redial Denied

(RLFD) Reversed Lamp Flash Denied supp-10

RLFA Reversed Lamp Flash Allowed

LOGIVOX must be assigned RLFA.

(RMMD) Remote Monitoring of Messages Denied vmba-24

RMMA Remote Monitoring of Messages Allowed

RMMO Allow Remote Monitoring of Messages and toOverride, if it is being already monitored

(RTDD) Call Redirection by Time of day denied basic-22

RTDA Call Redirection by Time of day allowed

(SFD) Second level CFNA Denied basic-10

SFA Second level CFNA Allowed

SFA requires the FNA Class of Service.



Administration

LD 11

(SMWD) Extended Message Waiting Indication Denied mw-24

SMWA Extended Message Waiting Indication Allowed

Only applies for M3903, M3904 and M3905 units.

(STSD) Set-to-Set Messaging Denied arie-25

STSA Set-to-Set Messaging Allowed

Only applies for M3903 and M3904 units.

(SWD) Station-to-Station Call Waiting Denied basic-8

SWA Station-to-Station Call Waiting Allowed

A Call Waiting key or CWT must be defined. Musthave CLS = HTD since hunting takes precedence.

(TEND) Tenant Service Denied tens-7

TENA Tenant Service Allowed

(ULAD) Deny access to Set Based Administration adminset-21

ULAA Allow access to Set Based Administration

Must have Set Based Administration (ADMINSET)package 256.

(UDI) Station is (not) restricted from receiving DID calls. supp-10

RDI Station is restricted from receiving DID calls.

(USMD) Meridian 911 position denied m911-19

USMA Meridian 911 position allowed

Must have Meridian 911 (M911) package 224.

(USRD) User Selectable Call Redirection Denied uscr-19

USRA User Selectable Call Redirection Allowed

(XMWD) Extended Message Waiting indication Denied vmba-24

XMWI Extended Message Waiting indication Allowed




LD 11

(VCE) Voice Terminal basic-5

DTA Data Terminal

VCE is used for voice TNs. DTA is used for data.

For 8 port Digital Line Cards, VCE for units 0-7 andDTA for units 8-15.

For 16 port Digital Line Cards, VCE for units 0-15and DTA for units 16-31.

For 24 port Digital Line Card, VCE for units 0-23 andDTA is for units 24-31.

Note: 24 port Digital Line Card not supported on Option11C

(VMD) Server Voice Messaging Denied cls-8

VMA Server Voice Messaging Allowed

(WTA) Warning Tone Allowed basic-1

WTD Warning Tone Denied

(XHD) Exclusive Hold Denied dhld-4

XHA Exclusive Hold Allowed

CPND Calling Party Name Display cpnd-19

NEW New CPND entry

OUT Delete CPND entry

CHG Change CPND entry

Must have Calling Party Name Display (CPND)package 95 and CPND data block defined in LD 95.

CPND_LANG Calling Party Name Display Language cpnd-19

(ROM) Roman

KAT Katakana

CTYP (XDLC)EDLC

Card type is 16 port DLCCard type is 24 port DLCVCE/DTA

Note: EDLC not supported on Option 11C

basic-25



Administration

LD 11

CUST xx Customer number associated with this set as definedin LD 15

basic-1

DBA (0)-1 Display-Based Accessory

Note: The Key-Based Accessory (KBA) and Display-Based Accessory (DBA) are mutually exclusive.

arie-25

DCD Dynamic Carrier Detect arie-14

(ON) Enables Dynamic CD

OFF Carrier Detect starts as inactive and follows the stateof the call. With DAC, DCD is only prompted if TYPE= R232.

DCFW x...x Default Call Forward DN. Prompted for VirtualTerminals only.

Where:x...x = Default Call Forward DN where calls are to beforwarded. Maximum of 31 digits allowed.

Precede with X to remove.

arie-25

DELETE_VMB Delete Voice Mailbox vmba-19

(YES) Remove the Voice Mailbox from the Meridian 1 andMeridian Mail

NO Remove the Voice Mailbox from the Meridian 1

DELETE_VMB is prompted if REQ = OUT and TNhas an associated Voice Mailbox. DELETE_VMB isallowed if the DN is a single appearance or multipleappearance DN on a single TN.

DEM Data Equipment Mode. Prompted if TYPE = R232. dac-16

(DCE) Data Carrier Equipment

DTE Data Terminal Equipment




LD 11

DES d...d ODAS Station DesignatorEnter a 1-6 alphanumeric character representing anOffice Data Administration System (ODAS) StationDesignator.

odas-1

DGRP (1)-5 Device Group

DGRP designates an AST BCS set into a specificdevice group. It is recommended that an ASTphantom (BCS) TN should be a non-display BCSset. An AST BCS set of a phantom loop cannot bean ACD set.

basic-20

DISPLAY_FMT Display Format for CPND name cpnd-19

(FIRST,LAST)

May be input as FIRST

To view names as John Doe

LAST,FIRST

May be input as LAST

To view names as Doe John

DLNG Language preference for the DAC prompts. dac-16

(ENG) English

FRN French

Prompted if TYPE = R232 or R422.

DN x..x yyyy Directory Number (x..x) and CLID table entry (yyyy)

The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.DN is not prompted for Option 11C model sets or ifDIG is defined.

Range for CLID table entry is: [(0) -(value entered for SIZE prompt in LD 15 minus 1)]

basic-12

DNAN (DNAA) Customer Attendant DN (ATDN) + AttendantNumber (ANUM) are used as ANI DN in 3WT ANImessages.

cist-21



Administration

LD 11

DNAD ANDN of outgoing 3WT route is used as ANI DN in3WT ANI messages.

Prompted with Commonwealth of IndependentStates (CIST) package 221.

DNDR (0)-120 Delay Value in seconds.

A DNDR value of 0 disables this feature. If the DNDRvalue is an odd number, then it is incremented to thenext even number.

basic-21

DNRI (0)-4 Distinctive Number Ringing index for Incoming calls

The index NDR1-4 BCS is defined in LD 56

edrg-24

DNRO (0)-4 Distinctive Number Ringing index for Outgoing calls

The index NDR1-4 BCS is defined in LD 56

edrg-24

DSPL (0)-500 Length of portable display (in characters). basic-22

DSPT (0)-2 Type of portable display:0 = display is numeric1 = display is alphabetic2 = display is alphanumeric

basic-22

DTAO Data Option, not prompted if TYPE = MCU. arie-18

(MPDA) Software for Meridian Programmable Data Adapter

MCA Software for Meridian Communications Adapter

The DTAO prompt determines the downloaded data,system, and operating parameters.




LD 11

DTMK x...x Data Mode Key number for a dynamic voice/dataTN.

DTMK is prompted if the TN has both CLS = VCEand CLS = FLXA. There can be only one data modekey per TN. Any response to DTMK will overwrite aprevious setting.

When changing from CLS = DTA to CLS = VCE,CLS = WTA should also be assigned to avoid conflictwith CLS = CPTA.

Where x...x = number of the SCR/SCN key to bedesignated as the data mode key. This cannot bekey 00.

basic-22

<cr> No data mode key. TN is not a dynamic voice/dataTN.

DTR Data Terminal Ready settings arie-14

(OFF) Dynamic DTR

ON Forced DTR, force the data port to always be readyfor transmission.

With the Data Access Card (DAC). DTR is promptedif TYPE = R232.

DTYP Data Station Type amp-5

(IOS) Inbound/Outbound Data Station

IDS Inbound Data Station

ODS Outbound Data Station

DUP (FULL) Full Duplex arie-14

HALF Half Duplex

ECHG (NO) YES Easy Change

This allows change to any prompt in this programwithout having to <cr> through all unrelated prompts.ECHG is prompted when REQ = CHG.

basic-12



Administration

LD 11

EFD x...x Flexible CFNA DN for External calls

EFD is the DN to which external calls are routedwhen there is no answer, if one of the followingcustomer options is defined in LD 15:


A Group Hunt DN can be entered.

The DN can be up to 4 digits without DirectoryNumber Expansion (DNXP) package 150, or 13digits with DNXP package 150.

Call Forward by Call Type Allowed and Forward NoAnswer must be defined as the Class of Service(CLS = CFTA and FNA). LDNs, DLDNs, and PrimeDNs will be accepted as valid input.

optf-10

EHT x...x External Hunt DN

EHT is the DN hunted for by external busy callswhen:

• Class of Service is Call Forward by Call TypeAllowed (CFTA) and Hunting Allowed (HTA)

• the LD 15 prompt FNAD, FNAT, orFNAL = HNT

A Group Hunt DN can be entered.

This DN can be up to 4 digits without DirectoryNumber Expansion (DNXP) package 150 or 13 digitswith DNXP package 150.

LDNs, DLDNs, and Prime DNs are accepted as validinput. To remove EFD or EHT DNs, change CFTAClass of Service to CFTD. Prompted when CFTA isdefined.

basic-10

000 Short Hunt for external calls

ELKP x...x Electronic Lock Password. Length is 1-15 digits ffc-15

ESN x...x Electronic Serial Number for a portable. Length is 11Hex digits.

basic-22




LD 11

FCAR Forced Charge Account Restricted chg-1

(NO) Must use Forced Charge Account

YES Restricted from using Forced Charge Account

Prompted if FCAF = YES in LD 15 and CLS = TLD,CUN or CTD.

FDN x...x Flexible CFNA DN

FDN is used for internal calls, if CLS is CFTA andFNA. FDN is used for all calls if CLS is CFTD andFNA.

FDN can be up to 4 digits without Directory NumberExpansion (DNXP) package 150 or 13 digits withDNXP package 150.

A Group Hunt pilot DN can be entered. Precede withX to delete.

FDN requires CLS = MWA or FNA. FDN is only usedif one or more of the following customer options aredefined in LD 15:


optf-1

FSVC (0)-9 Forced Out-of-Service Off-Hook Alarm Security DNindex.

When Forced Out-of-Service condition occurs on adigital telephone with Alarm Security Allowed(ASCA) Class of Service, the telephone isintercepted to a predefined DN.

Enter the index number (0)-9 of the DN defined byLD 15 prompts ODN 0-9. ODN is the acronym forChange Off-Hook Alarm Security Directory Numberoptions (OHAS DN).

basic-18

HDLC (NO) YES High Level Data Link Control arie-18

Prompted if V25 = YES.



Administration

LD 11

HOT Hotline arie-14

(OFF) Hotline is inactive for data port.

ON Enables Hotline for data port.

If HOT = ON, Auto Baud is forced OFF for the DataAccess Card.

HUNT x...x Hunt DN of next station in hunt chain

This Hunt DN can be up to 4 digits without DirectoryNumber Expansion (DNXP) package 150 or 13 digitswith Directory Number Expansion (DNXP) package150.

Precede with X to delete.

basic-10

000 Short Hunting

A Group Hunt pilot DN can be entered.

A A Control Directory Number (CDN) can be definedas a Hunt DN for both physical and phantom 500/2500 sets. When a CDN is configured in this way, acall which comes to a busy DN can be Hunting orCall Forward Busy to a CDN.

With Call Forward and Hunt by Call Type, this is theHunt DN for:

• internal calls if CLS = CFTA, or• for all busy calls if CLS = CFTD

IAPG 0-9 (0)-15 Meridian Link Unsolicited Status Message (USM)group

aml-16

IAPG assigns AST DNs to a status message groupdefined in LD 15. These groups determine whichstatus messages are sent for an AST set. Thedefault Group 0 sends no messages, while Group 1sends all messages.




LD 11

ICT 0-<NIPN> Intercept Computer Terminal or printer number

Number of Intercept Positions (NIPN) is defined inLD 15.

icp-16

INT Meridian 1/SL-100 Interworking arie-14

ON Enable Meridian 1 and SL-100 interworking

(OFF) Do not enable Meridian 1 and SL-100 interworking

ITEM aaaa yyy Respond with the desired program mnemonic (aaaa)and its new value (yyy).

ITEM is reprompted until only a carriage return <cr>is entered. For example:

basic-12

REQ CHG

TYPE SL1

TN lll ss cc uu

ECHG YES

ITEM KEY 07 ADL

KEY <cr> KEY is prompted until <cr> is entered

ITEM <cr>

REQ

<cr> Return to REQ

ITNA Idle TN for the Third Party Application. basic-20

(NO) Do not identify an Associated Set (AST) to be usedonly by Third Party Application

YES Identify an Associated Set (AST) to be used only byThird Party Application



Administration

LD 11

KBA

(0)12

Key-Based Accessory for M3904 and M3905 whichsupport key-based modules.

Configure keys up to and including 31Configure keys up to and including 53Configure keys up to and including 75

basic-24

KBD Keyboard Dialing Option dac-16

(ON) Enable Keyboard Dialing for data port

OFF Enables Hayes mode

KEEP_MSGS vmba-19

(NO) YES Preserve Meridian Mail Messages and currentpassword

KEY xx aaa yyyy (cccc or D) zz..z basic-1

Telephone function key assignments

The following key assignments determine callingoptions and features available to a telephone. Notethat KEY is prompted until just a carriage return <cr>is entered.

Where:

• xx = key number• aaa = key name or function• yyyy = additional information required for the

key• zz..z = additional information required for the

key aaa.

The cccc or D entry deals specifically with the CallingLine identification feature. Where:

• cccc = CLID table entry of (0)-N, where N =the value entered at the SIZE prompt in LD 15minus 1.

• D = the character “D”. When the character “D”is entered, the system searches the DN keysfrom key 0 and up, to find a DN key with CLIDtable entry. The CLID associated with thefound DN key will then be used.




LD 11

KEYNote: The position of the (cccc or D) field variesdepending on the key name or function.

You may enter a CLID table entry if aaa = ACD ,HOT d, HOT L, MCN, MCR, PVN, PVR, SCN orSCR.

Type xx NUL to remove a key function or feature.

Some data ports require specific key assignments.Refer to the Meridian Data Services NTPs forinformation regarding these requirements.

Key number limits that can be assigned are asfollows:

• 0-5 for M2006• 0-7 for M2008• 0-59 for M2616, varies with number of add-on

modules• 0-69 for SL1, varies with number of key/lamp

strips

If either the Meridian Programmable Data Adapter(MPDA) or the Display Module is equipped, then key7 on sets M2008, M2216, and M2616 sets and key 5on set M2006 will become Program keys whichcannot be used as function keys.

Any printout of the TN block will not show key 7because it is a local function key.

On the M2616, if CLS = HFA, key 15 on the voice TNdefaults to the Handsfree key. No other featureassignment is accepted.

Primary and secondary data DNs must be unique.

A station SCR, SCN, MCR, or MCN DN must beremoved as a member from all Group Hunt listsbefore the DN can be modified.



Administration

LD 11

On the M3903, keys 4-15 are blocked. No featureassignment is accepted for keys 2-15.

On the M3903,M3904, M3905, keys 27-31 arereserved. No feature assignment is accepted forkeys 17-31 other than NUL.

On M3904, no feature assignment is accepted forkeys 12-15.

On M3905, the craftsperson can assign NUL or aserver application on key 5. On key 6, thecraftsperson can assign NUL or a local application.

On M3905, the craftsperson can assign NUL or theprogram key on key 7.

On M3905, the craftsperson can assign AAG, AMG,ASP,DWC, EMR, MSB, or NRD on keys 8-11. Otherfeatures are blocked.

basic-24

xx AAG ACD Answer Agent key acdb-1


On the M3905 key numbers 8-11 are reserved forAAG, AMG, ASP, DWC, MSB and NRD.

basic-24

xx AAK Automatic Answerback key

AAA CLS and AAK key cannot be assigned to thesame telephone. Only one type of AutomaticAnswerback is allowed. M2616 telephone must haveCLS = HFA.

aab-1




LD 11

xx ACD yyyy (cccc or D) zzz bacd-1

Automatic Call Distribution key

Where:

• xx = key number (must be key 0)• yyyy = ACD DN or Message Center DN• cccc = CLID table entry of (0)-N, where N =

the value entered at the SIZE prompt in LD 15minus 1.

• D = the character “D”. When the character “D”is entered, the system searches the DN keys,from key 0, up to find a DN key with CLIDtable entry. The CLID associated with thefound DN key will then be used.

• zzzz = agent's position ID

yyyy and zzzz can be up to 4 digits, up to 7 digitswith Directory Number Expansion (DNXP) package150. Only ACD DN for Option 11C model set.

xx ACNT Activity Code entry key

This key must have an associated lamp and appliesto ACD-D and ACD-MAX only. ADS data block mustbe configured in LD 23.

acdd-13

xx ADL yy z...z optf-1

Autodial key

Where:

• xx = key number• yy = maximum length of the ADL DN. Valid

entries are: 4, 8, 12, (16), 20, 24, 28, 31. Notethat other values are rounded up to the nextvalid number.

• z...z = actual Autodial DN (this entry isoptional)



Administration

LD 11

xx AGT yyyy bacd-1

ACD Agent status key

Where: yyyy = agent's ID. The agent ID number canbe up to 4 digits, up to 7 digits with Directory NumberExpansion (DNXP) package 150. Must have CLS =SPV.

xx AMG ACD Answer Emergency call key


The Answer Emergency Key can be defined as asecondary supervisor’s Position ID. The secondarysupervisor’s Position ID can be NULL by default.

The Position ID of the ACD set cannot be changedonce the ACD set is acquired as a Human Agent.

On the M3905 key numbers 8-11 are reserved forAMG

acdb-1

basic-24

xx AO3 Three-Party Conference key basic-1

On the M3902 key number 4 is reserved for AO3,AO6, TRN, or NUL

basic-24

On the M3903, M3904, M3905 key number 18 isreserved for AO3, AO6, or NUL.

basic-24

On theI2004 key number 18 is reserved for AO3,AO6, or NUL.

mit-25

xx AO6 Six-Party Conference key basic-1

On the M3902 key number 4 is reserved for AO3,AO6, TRN, NUL

basic-24

On the M3903, M3904, M3905 key number 18 isreserved for AO3, AO6, or NUL.

basic-24

On theI2004 key number 18 is reserved for AO3,AO6, or NUL.

mit-25

xx ARC Attendant Recall key basic-1




LD 11

xx ASP ACD Supervisor call key (must have CLS = AGN)

On the M3905 key numbers 8-11 are reserved forNRD, MSB, AAG, AMG, DWC and ASP.

acdb-1

basic-24

xx ATW ACD Call Waiting Time indication key supp-14

xx AWC ACD Calls Waiting key

Must have CLS = AGN and Supervisor Position IDor SPID must be configured.

bacd-1

xx BFS TN Busy Forward Status key

Where: TN = Terminal Number to be screened. AKey cannot be assigned to a BRI set.

Note: It is possible to configure the TN of the same setagainst the BFS key only if the Class of Service is BFEA.

bfs-20

xx CA yy z...z basic-14

Combined No Hold Conference and Autodial key

Where:

• yy = maximum length of the CA DN. Validentries are: 4, 8, 12, (16), 20, 24, 28, 31. Notethat other values are rounded up to the nextvalid number.

• z...z = actual Autodial DN (this entry isoptional)

xx CAS Centralized Attendant Service key casm-1



Administration

LD 11

xx CFW yy z...z optf-1

Call Forward key

Where: yy = maximum length of the CFW DN

Valid entries for M2317 or M3000 sets are anyinteger in the range of (4)-23. For all other BCS typesets, you may enter any integer in the range of (4)-31.

Note: The default for M3900 series telephones is (16).

Where: z...z = Call Forward DN or range of DNswhere calls are to be forwarded (the target DN).Must be key 11 for LOGIVOX telephones.

A Group Hunt DN can be entered. If CLS = CFXD,the Call Forward number must be an internal DN.

On the M3903, M3904, M3905 key number 19 isreserved for CFW or NULL.

basic-24

On the I2004 key number 19 is reserved for CFW orNULL.

mit-25

xx CH D yy z...z basic-14

Combined No Hold Conference and Direct Hotlinekey

Where:

• yy = number of digits in target DN (1-31)• z...z = target DN

xx CH L yyy Combined No Hold Conference and Hotline List key

Where: yyy = 0-999 for Hotline list entry as defined inLD 18.

basic-14

xx CHG Charge account key chg-1

On the M3903, M3904, M3905 key number 25 isreserved for CHG or NUL.

basic-24

On the I2004 key number 25 is reserved for CHG orNUL.

mit-25




LD 11

xx CLT Configure Callers List key in context sensitive area,CLT/NUL are only options for key 27.

basic-25.4

xx COS Controlled Class of Service key ccos-7

xx CPN Calling Party Number key chg-1

On the M3903, M3904, M3905 key number 26 isreserved for CPN or NUL.

basic-24

On the I2004 key number 25 is reserved for CPN orNUL.

mit-25

xx CS yyyy Combined No Hold Conference and Speed Call key

Where: yyyy = Speed Call list number from 0-8190.Not available on M3000 telephones.

basic-14

xx CSD Conferee Selectable Display key. basic-23

xx CWT Call Waiting key

Only one CWT Key is allowed. Should have CLS =HTD since Hunting takes precedence.

basic-1

xx DAG Display ACD Agents key

This key displays the status of ACD agentsappearing on the supervisor's telephone. Must haveCLS = SPV and ADD or DDS.

bacd-1



Administration

LD 11

xx DIG yyyy zz R/V di-1

Dial Intercom Group key

Where:

• yyyy = group number, from 0-2045.• zz = member number from 0-99. The zz value

cannot be equal to or share the first digit of a 2digit number with the SPRE code. Forexample, if SPRE = 1, zz cannot be 1, 10,11...19.

• R = Ring option• V = Voice option

Must have maximum number of Dial IntercomGroups DGRP defined in LD 15.

If any member in a group has a two-digit membernumber, then all members have a two-digit number.The system adds leading zeros to other entries.

Prompted with Dial Intercom (DI) package 21.

xx DPU Directed Call Pickup key

Key is optional, dial access code can be used ifCLS = DPUA. Not available on M3000 telephones.This prompt appears with Directed Call Pickup(DCP) package 115.

dcp-12

xx DRC yyy DID Route Control key

Where: yyy = route number = 0-511

basic-15

xx DSP Display key

This key must have an associated key/lamp pair.

ddsp-1




LD 11

xx DWC yyyy bacd-19

ACD Supervisor Display Waiting Calls key

Where: yyyy = ACD DN. Up to 4 digits, up to 7 digitswith Directory Number Expansion (DNXP)package 150.

A maximum of eight DWC keys can be assigned perqueue on eight supervisors. Agent sets can onlyhave 1 SWC key for their own queue.

ACD agent telephones can support the displaywaiting calls key. Must have CLS = SPV and ADD orDDS.

TThe key can be used with supervisors and agents.


basic-24

xx EMR ACD Emergency key (must have CLS = AGN) acdb-1


basic-24

xx ENI yyyy ACD Enable Interflow key

Where: yyyy = DN. The DN can be up to 4 digits, upto 7 digits with Directory Number Expansion (DNXP)package 150.

Only one is allowed per ACD DN. Must have CLS =SPV.

acdb-1

xx EOVR Enhanced Override key povr-20

xx FDIS Force Disconnect Key pomw-25.4

xx GHD Group Hunt Deactivation key

A station user can toggle the PDN in and out of allgroups of which that PDN is a member.

pldn-15



Administration

LD 11

xx GPU Group Call Pickup key

The key is optional because a dial access code canbe used if CLS = GPUA. Not available on M3000telephones. Allowed with Directed Call Pickup (DCP)package 115.

dcp-12

xx GRC yy Group Call key grp-1

Where: yy = 0-63 for Group number as defined in LD18

xx HLD Hold supp-10

xx HOT Direct entry for Hotline model set key (Option 11C),Automatic termination DN is eight digits

hot-10

nn HOT D dd num DN m (cccc or D) hot-21

Two-way Hotline key

Where:

• dd = number of digits dialed• num = target_number (terminating DN is a

maximum of 31 digits)• DN = two-way hotline DN• m = one of the following Terminating Modes:

H = Hotline (default), N = Non-ringing,R = Ringing, or V = Voice






LD 11

xx HOT D nn x...x hot-10

Direct entry for One-way Enhanced Hotline key

Where:

• nn = number of digits dialed• x...x = Hotline terminating DN up to a 31 digit

maximum

xx HOT D nn x...x xxxx (cccc or D) hot-10

Direct entry for Two-way Enhanced Hotline key

Where:

• nn = number of digits in Target DN• x...x = Terminating DN up to a 31 digit

maximum• xxxx = optional two way Hotline DN. The DN

can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP)package 150.



nn HOT I dd num m hot-21

Intercom key

Where:

• dd = number of digits dialed• num = target_number (terminating DN max 31

digits)• m = one of the following Terminating Modes:

V = Voice (default), N = Non-ringing, orR = Ringing



Administration

LD 11

xx HOT L bbb hot-10

One-way Hotline key

Where: bbb = Hotlline list entry = 0-999. The Hotlinelist entry is defined in LD 18.

Note that the Hotline list NCOS overrides the setNCOS.

xx HOT L bbb xxxx (cccc or D) hot-10

Two-way list entry for Enhanced Hotline key

Where:

• bbb = List entry = 0-999• xxxx = Two-way Hotline DN. This DN can be

up to 4 digits, up to 7 digits with DirectoryNumber Expansion (DNXP) package 150.


• D = the character “D”. When the character “D”is entered, the system searches the DN keys,from key 0, up to find a DN key with CLIDtable entry. The CLID associated with thefound DN key will then be used.

Hotline list entry is defined in LD 18.

Note that the Hotline list NCOS overrides set NCOS.

xx ICF nn xxxx icf-19

Internal Call Forward key

Where: nn = Forward DN length. Valid entries areany integer in the range of (4)-31.

Where: xxxx = Forward DN (this entry is optional)

An ICF key can be configured if Call Forward isenabled.




LD 11

KY1 aaa Key 1 located far left, below dial pad.

Where: aaa = VUP (Volume Up) by default for KY1.Any function not requiring a lamp may be assigned.CLS must be LVXA.

KY2 aaa Key 2 located middle, below dial pad.

Where: aaa = VDN (Volume Down) by default forKY2. Any function not requiring a lamp may beassigned. CLS must be LVXA.

KY3 aaa Key 3 located far right, below dial pad.

Where: aaa = HLD (Hold) by default for KY3. Anyfunction not requiring a lamp may be assigned. CLSmust be LVXA.

supp-10

xx LNG M2317 Language Toggle key (No Language)

Where:

• xx = key 29• LNG = Language Toggle enabled• NUL = Remove Language Option

This feature allows set operator to set and resetlanguage display, toggling between French andEnglish versions on the alphanumeric display.

dlt2-9

xx LNK Last Number Redial key

LNRS defines the Last Number Redial Size.

For LOGIVOX telephones, key 8 is defined by setfirmware as the Last Number Redial key. The keydefinition is optional, because the user can press theDN key twice to activate Last Number Redial.

Must have OPT = LRA in LD 15 and CLS = LNA.

Inr-8

xx LSPK yyyy ohol-20

Loudspeaker key

Where: yyyy = associated loudspeaker DN orSPEKABUS channel



Administration

LD 11

xx MCK Message Cancellation Key

This key should only be programmed on MessageCenter sets.

mwc-1

xx MCN yyyy (cccc or D) zz..z basic-20

Multiple Call Non-Ringing key

Where:

• yyyy = DN• cccc = CLID table entry of (0)-N, where N =



• zz..z = additional information required for thekey aaa.

The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.The DN cannot appear simultaneously on a PBX setDN or as an SCR DN or SCN DN.

Once the MCN key has been defined, MARP isprompted.

On the M3901 and M3902 MCN cannot beconfigured on keys 1-5. MCN, if it is configured, mustbe assigned to key 0.

basic-24




LD 11

xx MCR yyyy (cccc or D) zz..z basic-20

Multiple Call Ringing key

Where:





The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.The DN cannot appear simultaneously on a PBX setDN or as a SCR Single Call or SCN DN.

Once the MCR key has been defined MARP isprompted.

On the M3901 and M3902 MCR cannot beconfigured on keys 1-5. MCR, if it is configured, mustbe assigned to key 0.

basic-24

xx MIK Message Indication Key

This key should only be programmed on MessageCenter sets.

mwc-1

xx MMM Voice/Data display key

Only key numbers 0-7 can be assigned for theM2008. M2x16 varies with additional add-onmodules. Maximum key number is 59.

The Data Port requires specific key assignments. AnISDLC line card, vintage C or higher, is required forM2006, M2008, M2216 and M2616 telephones.

amp-5



Administration

LD 11

xx MRK Message Registration Key

Requires PPM/Message Registration (MR)package 101 and CLS = ADD or DDS.

mr-10

xx MSB Make Set Busy key msb-1


basic-24

xx MWK yyyy mwc-1

Message Waiting Key

Where: yyyy = DN.

The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.With the Network Message Service featureequipped, the NMS-DN can be up to 13 digits.

On the M3902, key 5 is reserved for MWK or NUL.On the M3903, M3904, M3905, key 16 is reservedfor MWK or NUL.

basic-24

On the i2004 key 16 is reserved for MWK or NUL. mit-25

xx NHC No Hold Conference key basic-14

xx NRD Not Ready key

AGN or SPV Class of Service must be assigned.

bacd-1


basic-24

xx NSVC yyyy bacd-12

Night Service key (must have CLS = SPV)

Where: yyyy = ACD DN associated with that NightService. The DN can be up to 4 digits, up to 7 digitswith Directory Number Expansion (DNXP)package 150.

xx NUL Removes function or feature from key basic-1




LD 11

xx OBV Observe ACD agent key (must have CLS = SPV) bacd-12

xx OSN On-Site Notification key. esa-23

xx OVB Overflow Position Busy key aop-1

xx OVR Override key optf-1

xx PONW Priority Override/Breakin Networkwide key pomw-25.4

xx PRK Call Park key

The Transfer (TRN), or Six-Party Conference (A06)key plus a Dial Access code can be used instead ofthe Park key.

cprk-2

On the M3903, M3904, M3905, key 21 is reservedfor PRK or NUL.

basic-24

On the i2004 key 21 is reserved for PRK or NUL. mit-25

xx PRS Privacy Release key basic-1

On the M3903, M3904, M3905, key 24 is reservedfor PRS or NUL.

basic-24

On the i2004 key 24 is reserved for PRS or NUL. mit-25



Administration

LD 11

xx PVN yyyy (cccc or D) zz..z basic-20

Private Line Non-Ringing key

Where:





The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.Must have Private Line Directory Number (PRDN)defined in LD 14.

On the M3901, M3902, key 0 is reserved for PVN. basic-24

xx PVR yyyy (cccc or D) zz..z basic-20

Private Line Ringing key

Where:





The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.Must have Private Line Directory Number (PRDN)defined in LD 14.

On the M3901, M3902, key 0 is reserved for PRV. basic-24




LD 11

xx RAG ACD Ring Agent key (must have CLS =SPV) acdb-1

xx RCK y z Ringing Change Key

Where:

• y = first key/lamp strip controlled by key = (0)-6

• z = second key/lamp strip controlled bykey = 0-(1)-6.

Only one ringing change key per set is permitted.Requires International Supplementary Features(SUPP) package 131 and Ringing Change Key(RCK) package 193.

rck-15

xx RDL yy Redial stored number key

Where: yy = number of digits = 4, 8, 12, (16), 20, 23.Numbers between 5 and 22 are rounded up to thenext valid number.

snr-3

xx RGA Ring Again key

Must be key 10 on LOGIVOX telephones. RANAmay be activated if OPT = RNA in LD 15. When OPT= RND in LD 15, all sets with the RGA key will onlybe able to activate Ring Again Busy.

rga/ optf-20

On the M3903, M3904, M3905, key 20 is reservedfor RGA or NUL.

basic-24

On the i2004 key 20 is reserved for RGA or NUL. mit-25

xx RLS Release key

Requires CLS = LVXA. Key/lamp pair is not required.Must be KY3 on LOGIVOX telephones.

basic-1

xx RLT Configure Redial List key in context sensitive area,RLT/NUL are only options for key 28.

basic-25.4

xx RMK Room Status Key rms-10



Administration

LD 11

xx RMWKxxxx [yyyy]

Remote Message Waiting indication key

Where:xx= key numberxxxx = Message Center DN[yyyy] = DN to be monitored [optional]

mw-24

xx RNP yyyy basic-1

Ringing Number Pickup key

Where: yyyy = Ringing Number Pickup groupnumber is optional

If the group number is not entered, the key will pickup the group number assigned to the station. If thegroup number is entered, the key will pick up calls inthe specified group yyyy.

On the M3903, M3904, M3905, key 22 is reservedfor RNP or NUL.

basic-24

On the i2004 key 22 is reserved for RNP or NUL mit-25

xx RPAG yyyy rpa-15

Radio Paging key

Where: yyyy = Route Access Code

Coordinated Dialing Plan (CDP) Trunk SteeringCodes (TSC) and Distant Steering Codes (DSC) canbe entered against yyyy.

xx SCC yyyy optf-1

Speed Call Controller key

Where: yyyy = SCL list number 0-8190. SCL must bedefined in LD 18.

On the M3903, M3904, M3905, key 23 is reservedfor SCC, SCU, SSU, SSC or NUL.

basic-24




LD 11

xx SCN yyyy (cccc or D) zz..z basic-20

Single Call Non-Ringing key

Where:





The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.Once the SCN key has been defined, MARP isprompted.

On the M3901, M3902, key 0 is reserved for SCN. basic-24



Administration

LD 11

xx SCR yyyy (cccc or D) zz..z basic-20

Single Call Ringing key

Where:





The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.Use a single appearance DN to terminate VCC VoiceCall or SIG Signaling calls.

OOnce the SCR key has been defined, MARP isprompted.

On the M3901, M3902, key 0 is reserved for SCR. basic-24

xx SCU yyyy optf-1

Speed Call User key

Where: yyyy = SCL list number 0-8190. SCL must bedefined in LD 18.


basic-24

On the i2004 key 23 is reserved for SCC, SCU, SSU,SSC or NUL.

mit-25

xx SIG yyyy Signal key

Where: yyyy = Single appearance DN.

The DN can be up to 4 digits, up to 7 digits withDNXP package 150. Key/lamp is not required.

basic-1




LD 11

xx SSC yyyy System Speed Call controller key

Where: yyyy = SSC list number 0-4095. SSC listmust be defined in LD 18.

optf-1


basic-24

xx SSU yyyy optf-1

System Speed Call User key

Where: yyyy = SSC list number 0-4095. SSC listmust be defined in LD 18.

xx TAD Time and Date key

For SL-1 sets only, must have CLS = ADD or DDS,cannot be key 0.

ddsp-1

Blocked on the M3901, M3902, M3903, M3904,M3905.

basic-24

xx THF Centrex Trunk Switch Hook Flash key thf-14

xx TRC Malicious Call Trace key

Key/lamp not required. MCT is applied on a TNbasis. Yhis key can be configured on ACDtelephones. Allowed when CLS = MCTA.

mct-10

xx TRN Call Transfer key basic-1

On the M3902, key 4 is reserved for TRN or NUL.On the M3903, M3904, M3905, key 17 is reservedfor TRN or NUL.

basic-24

On the i2004 key 17 is reserved for TRN or NUL. mit-25

xx USR User Selectable Call Redirection key uscr-19

xx UST User Status key (must have UST = YES in LD15 andUST = YES in LD 23)

ims-2



Administration

LD 11

xx VCC yyyy Voice Call key

Where: yyyy = Single appearance DN. Not availableon M3000 telephones.

basic-1

xx VUP Volume Up key (must be assigned if Volume Down isassigned)

xx VDN Volume Down key (must be assigned if Volume Up isassigned)

xx WUK Guest entry of automatic Wakeup key (Key/lamp pairis required)

gewu-16

xx XMWKxxxx yyyy

Extended Message Waiting indication key

Where:xx= key numberxxxx = Message Center DNyyyy = DN to be monitored

mw-24

KLS 1-7 Number of key/lamp strips, including add-on key/lamp modules. Prompted if TYPE = SL-1

basic-1

LANG (0)-5 X Language choice for Automatic Wakeup (AWU)calls. Prompted with Multi-Language Wakeup(MLWU) package 206.

This entry defines the language presented for theAutomatic Wakeup Recorded Announcement (RAN),for language 0 through 5 as follows:

mlwu-16

(0) See RAN1/RAN2 in LD 15

1 See LA11/LA12 in LD 15





X Remove entry




LD 11

LDN (NO) Listed Directory Number Index as defined in LD 15 nldn-20

0-3 Listed Directory Number Index as defined in LD 15

0-5 Listed Directory Number Index as defined in LD 15

LHK Last Hunt Key number limit basic-10

(0)-7 For M2008

(0)-27 For M2616, varies with number of add-on modules(Option 11C)

(0)-59 For M2616, varies with number of add-on modules

(0)-69 For SL-1, varies with number of key/lamp strips

(0) No Last Hunt Key or remove Last Hunt Key (used forInternal/External Short Hunt)

LNRS 4-(16)-31 Last Number Redial Size

Enter the maximum number of digits that can bestored. Valid entries are 4, 8, 12, (16), 24, 28, or 31.Invalid entries are rounded up to the next valid entry.

Inr-8

LPK Line Preference Key limit (last key scanned forAutomatic Line Preference)

Isel-4

(0)-5 For M2006

(0)-7 For M2008

(0)-27 For M2616, varies with number of add-on modules(Option 11C)

(0)-59 For M2616, varies with number of add-on modules

(0)-69 For SL-1, varies with number of key/lamp strips

Prompted when CLS = IRA, NIA or OLA.

LTN 1-253 0-15 Logical TN and AUX link number amp-5

This prompt appears when CLS = IMA and the validAPL link is defined in LD15.



Administration

LD 11

MARP (NO) YES Multiple Appearance Redirection Prime

Use TN as the Multiple Appearance DN RedirectionPrime. The MARP prompt, or MARP information,appears following the DN KEY designation, and isassociated with those DN assignments.

basic-18

MAUT (NO) YES Modify Authorization Codes for this telephone ssau-19

This prompt appears with Station SpecificAuthorization Codes (SSAU)package 229 and CLS =AUTR.

MIN x...x Mobile Identification Number for a portable. Length is10 BCD Digits.

basic-22

MLNG a...a Language selection for the M3902, M3903, M3904,or M3905.

Where:

a...a = <CR> no change.

a...a = ENG, FRE, GER, DUT, SPA, ITA, NOR, SWE,DAN, POR, FIN, POL, CZE, HUN, JAP, RUS, LAT,TUR.

basic-25.4

MLWU_LANG Language choice for Automatic Wakeup (AWU)calls.

This entry defines the language presented for theAutomatic Wakeup Recorded Announcement (RAN),for language 0 through 5 as follows:

mlwu-19

(0) See RAN1/RAN2 in LD 15






X Precede with X to remove




LD 11

MOD Mode arie-14

(NO) Network is required for Meridian Programmable DataAdapter

YES Modem synchronizes to clock in external device,such as QMT21

MODL 1-127 Model number basic-16

This prompt appears for Option 11C model sets.

MPHI (NO) YES Meridian Communications Unit used as MPHinterface

mph-19

Prompted if TYPE = MCU.

MPR 0-511 Modem Pool Route number amp-5

NAME Calling Party Name Display name cpnd-21

aaaa,bbbb First name comma Last name.

For example, John Doe is entered as John,Doe. Thefirst single comma is treated as the delimiter. Up to27 characters (including the comma) may be input.The last occurrence of the first comma group servesas the name delimiter and is translated into a spacebetween the first and last name.

aaaa When the delimiter is omitted, the input is stored as afirst name.

aaaa, When the delimiter follows the input, the input isstored as the first name.

,bbbb When the delimiter precedes the input, the input isstored as a last name.

NCOS (0)-99 Network Class of Service group ncos-1



Administration

LD 11

OHID (0)-9 Off-Hook Alarm Security DN index for off-hook orinterdigit timeout.

basic-18

When a dial tone or interdigit timeout occurs on a setwith Alarm Security Allowed (ASCA) Class ofService, the set is intercepted to a predefined DN.

Enter the index number (0)-9 of the DN defined byLD 15 prompts ODNx.

OPE (NO) YES Change data port Operating Parameters mcu/arie-19

PAR (SPAC) Space Parity basic-1

EVEN Even Parity

ODD Odd Parity

MARK Mark Parity

PBDO Port Busy when DTR off dac-16

(OFF) Disabled

ON Key 7 is automatically assigned as the Make SetBusy (MSB) key

Switching to any other mode will force PBDO to OFF.Prompted if TYPE = R232 in operating modes 8 or12.

PLEV 0-(2)-7 Priority Level, prompted with Priority Override/Forced Camp-On (POVR) package 186 or EnhancedDPNSS1 Services (DPNSS_ES) package 288.

povr-20

2 = set can override sets of level 1 and 2, and can beoverridden by sets of level 2-7.

POS xxxx ACD position ID. Prompted when SFMT = AUTO,TNDN, TN or DN.

basic-12




LD 11

PRI Priority level for Automatic Call Distribution (ACD)agent

pagt-12

(1)-48 Valid range for systems 11C, 51C, 61C, and 81C.

(1)-32 Valid range for all other system options.

The agent with the lowest number assigned has thehighest priority and is the first ACD agent to receivecalls. (Where Priority 1 has the highest priority level).

PRI is prompted with Automatic Call Distribution,Priority Agent (PAGT) package 116 and CLS = AGNor SPV.

PRM Prompt for terminal or host mode arie-14

(ON) Terminal or Keyboard dial mode, prompts are outputby data unit

OFF Host mode prompts are not output by data unit

PSDS (NO) YES Public Switched Data Service option arie-18

With PSDS = YES, transmission will be synchronousand the baud will be 56K or 64K. 56K is the default.

PSEL Protocol Selection, DM-DM or T-link arie-18

(DMDM) DMDM is used by Meridian 1 data devices such asASIM, AIM, ADM, SADM, Asynchronous DataOption or ADO, and MPDA. MCA can use bothprotocols.

TLNK TLNK protocol is used by SL-100 and DMS datadevices

This prompt appears if DTAO = MCA, or TYPE =MCU

PUTYP (PRIVATE)IS-41

Portable Subscriber Type IS-41-24

RCO (0)-2 Ringing cycle option for Call Forward No Answer uscr-18

This prompt appears when CLS = FNA or MWA (orboth)



Administration

LD 11

REQ: Request basic-19

? To get a list of possible responses

CHG Change existing data block

CPY 1-32 Copy or create 1 to 32 new station data block(s)automatically from the specified station data block.Option 11C model sets cannot be copied.

END Exit overlay program

MOV Move data block from one TN to another.

MOV command can be used to move digital "IPE"telephones from one loop, shelf, card, unit to anotherlscu with the following restrictions (includes movesacross Superloops):

-ACD sets must not be moved. Remove (out) dataand re-enter at destination.

-Cannot be used for Option 11C model sets

MOV command can be used to move digital "EPE"telephones from one unit or card to another, but doesnot support moving these phones across shelves orloops.

MOV PAIR command can be used providing thesystem is on Rls 24 or 25. This command will notfunction properly on rls 15 - 23, recommend usingMOV on these releases of software.

basic-25.4

Note: If moving a voice unit with an associated data unit,the data unit must also be moved. On the NT8D02 DLCcard, both voice and data TN's can be moved by the MOVPAIR command.

Note: If Call Forward is activated prior to the set move, theCall Forward data will be moved to the destination set.

MOV PAIR Move voice TN and data TN data blocks on NT8D02Digital Line Card




LD 11

NEW Add new data block to the system

OUT Remove data block

Before removing an ACD agent telephone, firstremove the associated AGT key on the supervisor’stelephone. Select OUT and then NEW whenswitching resources between virtual and actual ACDDNs, to avoid unwanted information on ACD-Dreports.

The following is a list of valid responses. For furtherinformation, consult the appropriate Overlayprogram.

LD 32: CDSP CMIN CONV CPWD DISC DISIDISL DISN DISS DISU DSCT DSPS DSXPENCT ENLC ENLG ENLL ENLN ENLS ENLUENPS ENXP IDC IDCS IDU LBSY LDIS LIDLLMNT PBXT SDLC STAT SUPL TRK XNTTXPCT XPEC

LD 20: LTN LUC LUDU LUU LUVU PRT

LD 10: CHG CPY MOV NEW OUT

RNPG (0)-4095 Ringing Number Pickup Group grp-1

To remove a telephone from a group, enter 0 inresponse to the RNPG prompt.

RTS (ON) OFF Request To Send applies only to asynchronousmode.

mca-18

SCI (0)-7 Station Category Indication priority level sci-7

The station category number 1 to 7 must be definedas attendant console Incoming Call Indicator. LD 15prompt ICI = CA1-CA7.



Administration

LD 11

SCPW xxxx Station Control Password ffc-15

Must equal Station Control Password Length (SCPL)as defined in LD 15. Not prompted if SCPL = 0.Precede with X to delete.

SECOND_DN Second DN sharing the Voice Mailbox vmba-19

x...x Second Directory Number. This DN can be up to 4digits, up to 7 digits with Directory NumberExpansion (DNXP) package 150.

X Deletes the second directory number

SFDN xxxx Secretarial Forwarding DN of secretary set ftcsf-15

This prompt appears if response to SFLT = BOSS.

SFLT Secretarial Filtering ftcsf-15

(NO) Assign no designation to telephone set

BOSS Designate telephone set as a Boss set

SEC Designate telephone set as a Secretary set

SEC (NO) and <cr> takes you to the next prompt.

This prompt appears with Boss Secretary Filtering(FTCSF) package 198.




LD 11

SFMT Select one of the following formats for the copycommand. The DN may be up to 4 digits, up to 7digits with Directory Number Expansion (DNXP)package 150.

basic-1

TNDN Manual selection of TNs and DNs or ACD positionIDs for ACD telephones.

The TN and DN or POS for ACD set prompts repeatn times as specified under the CPY n command.

TN I s c u TN of new set

DN xxxx DN of new set

POS xxxx ACD position ID of newset

TN The new DNs or ACD position IDs for ACDtelephones are provided by the system. You areprompted for the starting TN and DN or ACD positionID for ACD telephones and each TN.

The TN prompt repeats n times as specified underthe CPY n command.




DN The new TNs are provided by the system. You areprompted for the starting TN and each DN or ACDposition ID for ACD telephones.

The DN or POS for ACD sets prompt repeats n timesas specified under the CPY n command.






Administration

LD 11

AUTO The new TNs and DNs or ACD position IDs for ACDtelephones are provided by the system. You areprompted for the starting TN and DN or ACD positionID for ACD telephones.




SGRP (0)-999 Scheduled Access Restriction group number sar-20

This prompt appears with Scheduled AccessRestrictions (SAR) package 162. Must have groupdefined in LD 88.

SPID x...x Supervisor Position ID DN bacd-1

SPID is prompted for ACD packages B, C, and Dwhen CLS = AGN. SPID can be up to 4 digits, up to 7digits with Directory Number Expansion (DNXP)package 150.

SPWD xxxx Secure Data Password ssau-19

This prompt appears only if the password is definedin LD 15. If the password is not entered, the securitycodes will not print when PRT is requested.

SSU 0-4095 System Speed Call List number ssc-2

Precede with X to delete.

TEN 1-511 Tenant number tens-7

This prompt appears if Multi-tenant is configured forthe customer.

TGAR 0-(1)-31 Trunk Group Access Restriction. The default of (1)automatically blocks direct access.

basic-1




LD 11

THIRD_DN x...x Third DN sharing the Voice Mailbox

Third Directory Number. This DN can be up to 4digits, up to 7 digits with Directory NumberExpansion (DNXP) package 150.

X Deletes the third directory number

vmba-19

TN TN Terminal Number.The TN defines the location of the telephone set.

TN appears when REQ = NEW, CHG, MOV, MOVPAIR or OUT.

basic-1

l s c u Large system TN format: l s c u = loop, shelf, card,unit

Where l =

• 0-159: loops, superloops must be multiples offour, starting with superloop 0

• 0-255: loops, Option 81C

Where s =

• 0-3: PE shelves on loops defined TERM in LD17

• 0-1: PE shelves on loops defined TERD in LD17 and superloops

• 0: PE shelf on loops defined TERQ in LD 17

fnf-25

Where c =

• 1-10: PE cards of dual and enhanced loops.• 0-15: IPE cards of superloops.

Where u =

• 0-3: single density units• 0-7: double density units and SL-1 line cards• 0-15: integrated services digital line (ISDLC)

cards• 0-31: digital line cards or DLC

For a static voice or data TN, u = 0-31. To assignVCE to TNs (where u = 16-31), CLS must be FLXA.To assign DTA to TNs (where u = 0-15), CLS mustbe FLXA. See text regarding FLXA on page 148.



Administration

LD 11

c u Small system format: c u = card, unit

• c = 1-50• u = 0-31

basic-16

TOTN To Terminal Number basic-20

l s c u Large system TN format: l s c u = loop, shelf, card,unit

c u Small system TN format

This prompt appears when REQ = MOV . and is notprompted for Option 11C model sets.

TOV Timeout Value for the Data port, for M2006, M2008,M2216 and M2616 data port only

mcu/arie-19

(0) No Timeout

1 15 minutes

2 30 minutes

3 60 minutes

TRAN Port transmission type for the data port on M2006,M2008, M2216, M2616 telephones

mcu/arie-19

(ASYN) Asynchronous data transmission

SYN Synchronous data transmission

Asynchronous data modules cannot be set assynchronous. An MMPO with DTAO, MPDA, orMMPO supports SYN.

TYPE: TYPE: Type of data block basic-1

? To get a list of possible responses

2006 M2006 Digital telephone.1 DN per set.

2006 M Option 11C Model set

2008 M2008 Digital telephone.





LD 11



2016 M2009 Digital telephone





2216 M2216 Digital ACD telephone.






3000 M3000 Digital Touchphone.





3903V M3903 Virtual Terminal Set. arie-25

3903H M3903 Host Terminal Set




Administration

LD 11

3904V M3904 Virtual Terminal Set arie-25

3904H M3904 Host Terminal Set


CARD Unused line card data block, used for AutomaticTelephone Relocation.

CARDMLT Multi-line Telephone Line Card.

i2004 i2004 Digital Telephone mit-25

MCA Meridian Communications Adapter.

MCU Meridian Communications Unit.

MPORTBL Mobility Portable

OOSMLT Out of Service Multi-Line Terminal Unit.

Entering OOSMLT allows the administrator to markany unit, regardless of card density or type, “Out ofService”.

xpe-20

R232 NT7D16 Data Access Card (DAC) port in RS-232Data mode.

R232 M Option 11C Model set

R422 NT7D16 Data Access Card (DAC) port in RS-422mode

R422 M Option 11C Model set

SL1 SL-1 or M1000 series telephone data block

Not supported on Option 11C

The M2006, M2008, M2216, and M2616 requireISDLC line card Version C or greater. The data portrequires specific key assignments.




LD 11

V25 (NO) YES V.25 bis option, synchronous mode only. arie-18

VISI Visiting mmsn-22

(NO) TN is not for visiting portables

YES TN is for visiting portables

VLL (OFF) ON Virtual Leased Line arie-14

VMB Voice Mailbox vmba-19

NEW Add Voice Mailbox

CHG Change Voice Mailbox

OUT Remove Voice Mailbox

This prompt appears with Voice MailboxAdministration (VMBA) package 246.

VMB_COS Voice Mailbox Class of Service vmba-19

0-127 Valid range

WIRE Wire test. Prompted if TYPE = R232 or R422. dac-16

(OFF) Wire test disabled

ON System automatically tests wiring/cabling when DACinstalled.

XLST (0)-254 Pretranslation group associated with this station. pre-8

XPLN xx Expected name length cpnd-19

ZONE 0-255 Zone Number which i2004 set belongs

The zone prompt applies only when the type isi2004. Zone number is not checked against Overlay117.

mit-25



Administration

LD 20



AACS Application acquired set ngcc-22NO The TN is not acquired by an applicationYES The TN is acquired by an application

ADJUST PAPER THEN <cr> basic-1Adjust paper then <cr> to start printing

<cr> Start printing

ASID x...x Application Service ID from which the acquiredrequest originated

The ASID is used for sending the monitor/controlmessages to the application. The ASID value isupdated based on the applications’s Acquiremessage for the TN. Since the AML over Ethernet(ELAN) is used to communicate between theMeridian 1 and the application(s), the value of theexisting VSID might be used to uniquely identify theapplication that has acquired this device.

ASID is printed if AACS = YES.

ngcc-22

CALB 1 2 ... Call Filter Bitmap

CALB applies to messages such as PCI, DN update,etc.

This bitmap is downloaded by the application whichis used to control the sending of messages on behalfof the acquired TN. A numeric value would only beprinted if the corresponding set message is enabled.

CALB is printed if AACS = YES.

ngcc-22

CDEN SD Single Card Density basic-7DD Double Card Density4D Quadruple Card Density8D Octal Card Density<cr> For all card densities

CTYP (XDLC)EDLC

Card type is 16 port DLCCard type is 24 port DLC

Note: EDLC not supported on Option 11C

basic-25



LD 20

CUST xx xx Customer number as defined in LD 15 basic-1Print data range from first to last customer. Notprompted when:

1. REQ = LUU or LUC2. TYPE = SCL, DIG or TEM3. a complete TN is entered

<cr> Print data blocks for all customers

DATE dd mmm yyyy basic-1Print data from date specified. Where:

• dd = 1-31• mmm = JAN-DEC• yyy = year (e.g. 1993)

DATE is prompted for TN related data.<cr> Print data and show last activity date.ACT Print data from last activity date.

DES ODAS Station Designator odas-1d...d Print all units with ODAS designator. Enter a 1-6

alphanumeric character representing an Office DataAdministration System (ODAS) Station Designator.

d+ Print units starting with ODAS designator d+ Print units with no ODAS designator assigned<cr> Disregard ODAS designator

DES is prompted on TN related data The printing ofdata is subject to restrictions imposed by responsesto TN and DATE.

DGRP Dial Intercom Group basic-10-2045 DIG numbers per customer<cr> Print all Dial Intercom Groups for customer

DGRP is prompted when TYPE = DIG

DMC l s c

c

Digital Enhanced Cordless Telecommunications(DECT) Mobility Controller Location

Option 11C format

mc32-25

DMEM 0-99 Dial Intercom Group (DIG) Member number basic-1<cr> Print all DIG member numbers



Administration

LD 20

DN Directory Number basic-19

xxxx Print data block for DN<cr> Print data blocks for all DNxxxx <space>

If a space is entered after the Directory Number thesystem will reprompt for DN. A maximum of six DNscan be stacked and printed at one time.

x<cr> All DNs starting with first digit x (X000-X999)xx<cr> All DNs starting with first two digits xx (XX00-XX99)xxx<cr> All DNs starting with first three digits xxx (XXX0-

XXX9)

x-<cr> All DNs between X000-9999x-y<cr> All DNs between DN X000 through Y999xx-yyy<cr> All DNs between DN XX00 through YYY9

xxxx xxxx Two specific DNs. Up to a maximum of 8 DNs.xxxx-yyyy All DNs between XXXX and YYYY

EHNO xxxx External HUNT DN eht-10Up to 4 digits, up to 7 digits with Directory NumberExpansion (DNXP) package 150.EHNO is prompted when TYPE = EHT

FOR Print template information for telephone type basic-1500 Print data for 500/2500 telephones.2xxx Print data for 2000 type telephones (specify type).3xxx Print data for 3000 type telephones (specify type) basic-24SL1 Print data for SL-1 telephones.

GRNO 0-63 Group Call Group Number. Prompted whenTYPE = GRP.

grp-1

<cr> Print all group call groups.

GRP 1 - 4095 Group number to be printed grp-21<CR> All groups assigned to a speed call list are printed.

HTNO x...x Hunt Directory Number

Up to 4 digits, up to 7 digits with Directory NumberExpansion (DNXP) package 150. Prompted whenTYPE = HNT.

basic-1




LD 20

INFO Information for Templates basic-1FRM Print key/feature assignment templateUSE Print number of users of templateUSS Print TN using the templateDEF Print number of templates defined and number

allowedPrompted when TYPE = TEM

LSNO 0-8190 Speed Call Lists

When inputting list number for printout, non-DNinput exceeding 4 digits may be truncated. Only the4 right-most digits will be accepted and printed

basic-1

MODL xxx Option 11C Model number (1-3 digits) basic-15

MPHI YES NO Meridian Packet Handler Interface. mph-19Prompted when TYPE = MCU. Respond Yes if usingthe MCU for MPH interfaces.

NACT Next Activity odas-1(NO) Return to REQ promptYES Print current system data and end overlayEND End overlay activity

PAGE (NO) YES Data printed on a per-page basis basic-1Prompted only on TN related data

REQ: REQ: Request basic-1END Exit overlay programLTN List TN of TYPE specifiedLUC Print Unused Card data blocks of TYPE specifiedLUDU List Unused Data UnitsLUU Print Unused Unit data blocks of TYPE specifiedLUVU List Unused Voice UnitsPRT Print data block for the TYPE specified.

The following is a list of valid responses. For furtherinformation, consult the appropriate Overlayprogram.



Administration

LD 20

LD 32: CDSP CMIN CONV CPWD DISC DISIDISL DISN DISS DISU DSCT DSPS DSXPENCT ENLC ENLG ENLL ENLN ENLS ENLUENPS ENXP IDC IDCS IDU LBSY LDIS LIDLLMNT PBXT SDLC STAT SUPL TRK XNTTXPCT XPEC

LD 10 or 11: CHG CPY MOV NEW OUT

RNGE xxxx yyyy Range of list entries to be printed, inclusive from firstentry number to last entry number.

optf-1

<cr> Print All members of a specified SCL or SSC list.

SCNO 0-253 Speed Call list Number optf-10-8190 Speed Call list Number<cr> Print all lists.

Prompted when TYPE = SCL

SFNB 1 2 ... Set Feature Notification Bitmap

SFNB is used for messages such as: SFN (login),SFN (logout), ...

This bitmap is downloaded by the application whichis used to control the sending of SFN messages onbehalf of the acquired TN. A numeric value is printedonly if the corresponding message is enabled.

SFNB is printed if AACS = YES.

ngcc-22

SFRB 1 2 ... Set Feature Route Bitmap

SFRB is used for messages such as: SFR (login),SFR (logout), ...

This bitmap is downloaded by the application whichis used to control the sending of SFR messages onbehalf of the acquired TN. A numeric value is printedonly if the corresponding message is enabled.

SFRB is printed if AACS = YES.

ngcc-22

SPWD xxxx Security Password. This prompt appears when:

1. the Station Specific Authcode package (229) isequipped.

2. the security password is defined in LDs 10and 11.

ssau-19




LD 20

TBNO 1-254 Table Number for 16-Button DTMF supp-10Prompted when TYPE = ABCD

TEM xxxxxxx Template number basic-1<cr> Print data for all templates.

Prompted when TYPE = TEM

TEMP xxxx Telephone template number. Enter <cr> to print alltemplates.

basic-1

TEN Tenant tens-70 Shared customer resource stations1-511 Tenant Service stations<cr> Print data blocks for all tenants.

TN TN Terminal Number basic-1

loop Print data of the specified TYPE for this loop.

l s Print data of the specified TYPE for this loop andshelf

l s c Print data of the specified TYPE for this loop, shelfand card

l s c u Print data of the specified TYPE for this loop, shelf,card and unit.

sl ch Print data of the specified TYPE for this shelfloopand channel (format for Digital Trunk and PrimaryRate Interfaces).

card Print data of the specified TYPE for this card(Option 11C).

c 0 0 u For Option 11C

c u Print data of the specified TYPE for this card andunit (Option 11C).

c ch Print data of the specified TYPE for this card andchannel (digital trunks only) (Option 11C).



Administration

LD 20

n. . . n<space>System will prompt for TN. A maximum of six TNscan be stacked and printed at one time.

<cr> Print data for all TNs of the specified TYPE.

l s c u, l s c u List of TNs (up to 6)

l s c u, sl ch A TN and a trunk shelfloop/channel can be enteredon the same line

l s c, l s c All units within the specified starting and endingcards

l s, l s c u All units, including the specified starting shelf andending TN

l s c u All TNs starting with the specified TN and endingwith the last TN

Not prompted when TYPE = SCL, HNT, DIG, TEM,or GRP

loop, l s,l c u, l s c u,l ch

l = (0-255) Option 81C format with Fiber NetworkFabric

fnf-25




LD 20

TYPE: TYPE: Type of data block basic-1

500 500/2500 telephone500 M Option 11C Model

1250 M1250 Console

2000 M2000 type digital telephones

2003 2003 Digital telephone

2006 M2006 Digital telephone2006 M Option 11C Model



2016 M2016 Digital telephone


2112 M2112 Digital telephone2112 M Option 11C Model2216 M2216 Digital telephone (ACD terminal)

2216 M Option 11C Model

2250 M2250 Console



3000 M3000 Digital Touchphone3000 M Option 11C Model

4020 M4020 Model

ABCD 16-Button DTMF



Administration

LD 20

ADM Add-on Data ModuleData port interfacing with a data line card

ADM M Option 11C Model

ARIE Aries (M2006, M2008, M2016S, M2216 and M2616)sets and Meridian Communications Unit (MCU) datablocks

ATT QCW3 or QCW4 Attendant Console

ATVN Autovon trunks

AWR Automatic Wake Up RAN/Music trunk

AWR M Option 11C Model

BCS Business Communication Set

CAA Common Control Switching Arrangement (CCSA)Automatic Number Identification (ANI) trunk datablock

CAA M Option 11C Model

CAM CAMA trunk data blockCAM M Option 11C Model

COT Central Office Trunk (PSTN) data blockCOT M Option 11C ModelCPNW Call Pickup Network Wide data

CSA Common Control Switching Arrangement accessline

CSA M Option 11C Model

DAC Data Access Card

DCS Digital Communications Set mc32-25

DIC Dictation trunk data blockDIC M Option 11C Model

DID Direct Inward Dialing trunk data blockDID M Option 11C Model




LD 20

DIG Dial Intercom Group

DNB Directory Number Block

DSL Digital Subscriber Loop (S/T or U I/F for ISDN BRI)

DT2 2.0 Mb/s DTI output only

DTD Dial Tone Detector

DTR Digitone Receiver

EHT External Hunting

FEX Foreign Exchange trunkFEX M Option 11C Model

FGDT Feature Group D Trunk

GHT Group Hunt

GRP Group call

HNT Hunting

HTL Hot Line

i2004 i2004 Internet Telephone mit-25

IDA Integrated Digital AccessISA Integrated Services Access trunk (ISDN)

LUDN List Unused Directory Numbers.MCA Meridian Communications AdapterMCA M Option 11C Model

MCU Meridian Communications Unit

MDM Modem/Data Module. Data port interfacing withQPC60 500/2500 type card

MDM M Option 11C Model

MFC Multifrequency Compelled sender/receiver datablock



Administration

LD 20

MFE Multifrequency Signaling for Socotel sender/receiver

MFK5 2/5 Spanish KD3 MF Signaling kd3-20

MFK6 2/6 Spanish KD3 MF Signaling kd3-20

MFR Multifrequency Receiver (for Feature Group D)

MFVE Print Multifrequency Versatile units

MUS Music trunkMUS M Option 11C Model

OOSMLT Out-of-Service Multi-Line Terminal xpe-20

OOSSLT Out-of-Service Single Line Terminal xpe-20

PAG Paging trunkPAG M Option 11C Model

PBX PBX sets

PRE Pretranslation

PRI2 ACD Priority Agents

PWR Power data block

R232 NT7D16 Data Access Card(DAC) port in RS-232 Data mode data block

R232 M Option 11C Model

R422 NT7D16 Data Access Card(DAC) port in RS-422 mode data block

R422 M Option 11C Model

RAC Real Analog Channel

RAN Recorded Announcement trunkRAN M Option 11C Model

RCD Recorder trunkRDC Real Digital Channel

RLM Release Link Main trunk




LD 20

RLM M Option 11C Model

RLR Release Link Remote trunkRLR M Option 11C Model

SCL Regular and System Speed Call Lists

SL1 SL-1 and M1109 sets, QCW and M1250 console(Not supported on Option 11C)

SSL Special Service List

TCON Tandem Connection for MPH and PRI connections

TDET Tone Detector

TEM Template

TIE TIE trunkTIE M Option 11C Model

TNB Terminal Number

TRK Trunk data block

VAC Virtual Analog Channel

VDC Virtual Digital Channel

VMB Voice Mailbox information

WAT Wide Area Telephone Service trunkWAT M Option 11C Model

XTD Extended Dial Tone Detector and Digitone Receiver

<cr> Print all



Administration

LD 20

USFB 1 2 ... Unsolicited Status Message (USM) Filter Bitmap

USFB applies to messages such as:

• Onhook, Offhook, Ringing, Active,Disconnect, Unringing, Hold, Restore, Ready,Not Ready, Walkaway, Walkaway Return,Reserved, Unreserved, ...

This bitmap is downloaded by the application whichis used to control the sending of USM messages onbehalf of the acquired TN. A numeric value wouldonly be printed if the corresponding message set isenabled.

USFB is printed if AACS = YES.

ngcc-22

VMB_STATE vmba-19nnnn Print based on Voice Mailbox State



Administration

LD 21



AACR (NO) The route is not acquired by the application ngcc-22YES The route is acquired by the application

ACOD x...x Access Code for route basic-1Up to 4 digits, up to 7 digits with Directory NumberExpansion (DNXP) package 150.

<cr> Print data for all route access codesThis prompt appears when ROUT = <cr>

ASID x...x Application Service ID from which the acquiredrequest originated

ASID is used for sending route status messages. TheASID value is updated based on the application’sAcquire message for the route. Since the AML overEthernet (ELAN) is used to communicate betweenthe Meridian 1 and other applications, the VSID valuemight be used to uniquely identify the applicationwhich has acquired that device.

ngcc-22

CALB 1 2 ... Call Filter Bitmap

CALB applies to messages such as PCI, DN update,etc.

This bitmap is downloaded by the application which isused to control the sending of messages on behalf ofthe acquired TN. A numeric value would only beprinted if the corresponding set message is enabled.

CALB is printed if AACR = YES.

ngcc-22

CUST xx xx Customer number basic-1Print data range from first to last customer

Not prompted when:

• REQ = LUU or LUC• TYPE = SCL, DIG or TEM• a complete TN is entered


HOUR 0-23 All routes tested by ATM for this hour<cr> Print routes tested by ATM for all hours



LD 21

OPR (NO) YES Outpulsing RouteThis prompt appears when OPOA is equipped.Prompted on TN related data

REQ Request basic-1END Exit overlay programLTM Print trunk route by TN and member numberPRT Print data block for the TYPE specified.

RNGE aa ... aa CLID entry to be printed

You may print one CLID entry or several CLIDentries. If you want to print several CLID entries,separate each entry with a comma. Each CLID entrymust be between 0 and the number entered for theprompt SIZE in LD 15.

isdn-22

ROUT 0-511 Route number basic-1<cr> Print data for all routes

This prompt appears when TYPE = CRB or RDB

SFNB 1 2 ... Set Feature Notification Bitmap

SFNB is used for messages such as: SFN (login),SFN (logout), ...

This bitmap is downloaded by the application which isused to control the sending of SFN messages onbehalf of the acquired TN. A numeric value is printedonly if the corresponding message is enabled.

SFNB is printed if AACR = YES.

ngcc-22

SIZE - - - CLID table entry size.

The SIZE prompt and the SIZE value print outautomatically after the CUST prompt.

isdn-22

TYPE Type of data block basic-1

AML_DATA Application Module Link

ANI_DATA Automatic Number Identification numbers

ATM Automatic Trunk Maintenance (ATM) data block

ATT_DATA QCW3 or QCW4 Attendant Console



Administration

LD 21

AWU_DATA Enable Automatic Wake-up

CASK Centralized Attendant Service (CAS) key data block

CAS_DATA Centralized Attendant Service

CCS_DATA Controlled Class of Service options

CDB Customer Data Block

Note: If you need information regarding SystemPasswords, print PWD_DATA field by itself. PWD_data willnot be provided by printing CDB.

CDR_DATA Call Detail Recording

CLID Calling Line Identification entry data

CRB Code Restriction data block

FCR_DATA New Flexible Feature code options

FFC_DATA Flexible Feature Codes

FTR_DATA Feature

HSP_DATA Hospitality

ICP_DATA Intercept Positions and interrogation sets. Promptedwhen REQ = PRT

IMS_DATA Integrated Messaging System

INT_DATA Alarm ring for Internal calls

ISLL IASL ISDN Signaling Link data block. This promptappears when REQ = PRT.

LDN_DATA Listed Directory Number

MPO_DATA Multi-party options

NET_DATA ISDN and ESN networking options

NIT_DATA Night Service options




LD 21

NPID Numbering Plan Digit or Information Digit table

OAS_DATA Off-Hook Alarm Security options

PPM_DATA Periodic Pulse Metering options

PWD_DATA Print the system Passwords

RDB Route Data Block

A printout of a route with the Night Key for DID DigitManipulation (NKDM) active will show * opposite thevalue for DCNO or NDNO.

RDR_DATA Call Redirection

ROA_DATA Recorded Overflow Announcement

SCH Schedule data block for ATM

SDP Secure data password

SRDT Set Relocation Data block

TIM_DATA System Speed Call

TST_DATA Loop Test trunk data

USFB 1 2 ... Unsolicited Status Message (USM) Filter Bitmap

USFB applies to messages such as:

• Onhook, Offhook, Ringing, Active, Disconnect,Unringing, Hold, Restore, Ready, Not Ready,Walkaway, Walkaway Return, Reserved,Unreserved, ...

This bitmap is downloaded by the application which isused to control the sending of USM messages onbehalf of the acquired TN. A numeric value wouldonly be printed if the corresponding message set isenabled.

USFB is printed if AACR = YES.

ngcc-22



Administration

LD 22



ADJUST PAPER THEN <cr> basic-1Adjust paper then <cr> to start printing

<cr> Start printing

CUST xx xx Customer number basic-1Print data range from first to last customer. Notprompted when:

1. REQ = LUU or LUC2. TYPE = SCL, DIG or TEM3. a complete TN is entered


DATE dd mmm yyyy basic-1Print data from date specified. Where:

• dd = 1-31• mmm = JAN-DEC• yyy = year e.g. 1993

DATE is prompted for TN related data

<cr> Print data and show last activity dateACT Print data from last activity date

DES Designator

DES is prompted on TN related data The printing ofdata is subject to restrictions imposed by responsesto TN and DATE.

odas-1

d...d Print all units with ODAS designator ddddddd+ Print units starting with ODAS designator d+ Print units with no ODAS designator assigned<cr> Disregard ODAS designator

DN Directory Number basic-19xxxx Print data block for DN<cr> Print data blocks for all DNxxxx <space>

If a space is entered after the Directory Number thesystem will reprompt for DN. A maximum of six DNscan be stacked and printed at one time.



LD 22

x<cr> All DNs starting with first digit x (X000-X999)xx<cr> All DNs starting with first two digits xx (XX00-XX99)xxx<cr> All DNs starting with first three digits xxx (XXX0-

XXX9)

x-<cr> All DNs between X000-9999x-y<cr> All DNs between DN X000 through Y999xx-yyy<cr> All DNs between DN XX00 through YYY9

xxxx xxxx Two specific DNs. Up to a maximum of 8 DNs.xxxx-yyyy All DNs between XXXX and YYYY

NACT Next Activity odas-1(NO) Return to REQ promptYES Print current system data and end overlayEND End overlay activity

PAGE (NO) YES Data printed on a per-page basis basic-1Prompted only on TN related data

PWD2 x...x Enter second level administration password(Password 2) to print information relating to allpasswords.

Valid characters are 0-9, A-Z, a-z. Length is 4-16characters.

basic-1

<cr> To print only the information regarding the LimitedAccess to Overlay password used to login.PWD2 is prompted when REQ = PWD orTYPE = PWD.

REQ Request basic-1END Exit overlay programISS Print generic version and IssueISSP Print System and Patch InformationPRT Print data block for TYPE specifiedPWD Print the system PasswordsSLL Print System Loop LimitsSLT Print System Limits : Incremental Software

Management (ISM parameters and keywords)

Note: If an Incremental Software Management (ISM) limitis set to the maximum value 32767, then the information forthat ISM will not be printed. This does not apply for the TNsISM



Administration

LD 22

TID Print the Tape ID. (S/W Cart ID and Site ID forOption 11C).

TN Terminal Number

TN is not prompted when TYPE = SCL, HNT, DIG,TEM, or GRP.

basic-1

loop Print data of the specified TYPE for this loop.l s Print data of the specified TYPE for this loop and

shelfl s c Print data of the specified TYPE for this loop, shelf

and cardl s c u Print data of the specified TYPE for this loop, shelf,

card and unit.

l s c u, l s c u List of TNs (up to 6)

l s c u, sl ch A TN and a trunk shelfloop/channel can be enteredon the same line

l s c, l s c All units within the specified starting and endingcards

l s, l s c u All units, including the specified starting shelf andending TN

l s c u All TNs starting with the specified TN and endingwith the last TN

sl ch Print data of the specified TYPE for this shelfloopand channel (format for Digital Trunk and PrimaryRate Interfaces).

<cr> Print data for all TNs of the specified TYPE.

card Print data of the specified TYPE for this card(Option 11C).

c 0 0 u For Option 11Cc u Print data of the specified TYPE for this card and

unit (Option 11C).c ch Print data of the specified TYPE for this card and

channel (digital trunks only) (Option 11C).

n. . . n<space>System will prompt for TN. A maximum of six TNscan be stacked and printed at one time.




LD 22

TYPE TYPE Type of data block basic-1

ADAN All I/O devices

ADAN AML Application Modules

ADAN DCH D-channel and backup D-channels

ADAN FDK Floppy Disk units

ADAN HST History Files

ADAN PRT System Ports

ADAN TTY System Terminals

ADM Add-on Data ModuleData port interfacing with a data line card

ADM M Option 11C Model

AHST All History File

ALARM Print Filter and expection tables

APL Auxiliary Processor Links

ATRN Print Meridian Modular Telephone Transmissionparameters

AUDT Audit Trail bufferOnly system Administrators are allowed to print theAudit Trail. They must first respond to PWD2 inLD 17 to define the password.

CARD Card data block (used for Automatic Set Relocation)

CEQU Common Equipment

CFN Configuration record data block

CHID Channel ID for ISDN Signaling Link (ISL)

CINV Core Inventory list (Option 81C)

DCP Directed Call Pickup



Administration

LD 22

DSDN Data Services Directory Number or PTE IS

GHT Group Hunt

GRP Group call

IMA IMS Message Attendant

IADN Individual Attendant Directory Number

ISS Generic version and Issue

ISSP System and Patch Information

OVLY Print Overlay area information

PARM System Parameters

PHST Previous History FileAll History File records since last request

PKG Packages equipped. For a list of packages, refer topages page 33 or page 45.

PKG xxx Check equipped/restricted status of packagenumber xxx

PSWV Peripheral Software Version(s) downloaded to:NT8D01 Controller cardsNT8D04 Network cardsNT8D018 Network/Digitone Receiver cardsNote: The version of peripheral software i.e. PSWVVERSION is not printed here for option 11C. It is printedalong with other Option 11C specific data in LD 143.

PWD Print the system Passwords

REF Loop Reference trunk data

RLM Release Link Main trunkRLM M Option 11C Model

RLR Release Link Remote trunkRLR M Option 11C Model

SCI Station Category Indication data block




LD 22

SFA Second level Forwarding Allowed

SFD Second level Forwarding DeniedSLL System Loop Limits

VAS Value Added Server data vns-21

VHST View History File

VHST View the History File hist-19

(%ON) Turn ON display features% OFF Turn OFF display features

This command is used to enable or disable thefollowing three display features:

• brackets to surround the current index ([])• percent symbol (%) preceding each History

File line• relative location within the History File (in

percentage)

VHST accepts abbreviated responses.

BFIND aaaa Search backward in the History File

This command can be used to search backward,starting at the current index location, for the string“aaaa.” If necessary, the file will wrap until it returnsto the same location.

The text string can be up to 12 characters. Specialcharacters like space, slash (/), and colon (:) areaccepted. Leading or trailing spaces are ignoredunless enclosed in double quotes. For example, thespaces denoted here are ignored:<SP><SP>INI<SP>. The spaces in this string,however, are included in the search:“<SP><SP>INI<SP>”.

When the string is found, the system displays thecurrent index location. Five text lines are shown,with the middle line containing the sought string. TheVHST prompt is re-displayed to allow morecommand use. If the string is not found, VHST isreprompted to allow more command use.



Administration

LD 22

BFIND Repeats the previous backward search

DOWN BOT Moves to the top of the file

DOWN Move forward 6 lines in the History File

This command can be used to move forward in theHistory File, toward the end. If x exceeds the end ofthe file, the end will be shown.

When the move is complete, VHST is reprompted toallow more command use.

FIND aaaa Search Forward in the History File

This command can be used to search forward,starting at the current index location, for the string“aaaa.” If necessary, the file will wrap until it returnsto the same location.

The text string can be up to 12 characters. Specialcharacters like space, slash (/), and colon (:) areaccepted. Leading or trailing spaces are ignoredunless enclosed in double quotes.

For example, the spaces denoted here are ignored:<SP><SP>INI<SP>. The spaces in this string,however, are included in the search:“<SP><SP>INI<SP>”.

When the string is found, the system displays thecurrent index location. Five text line are shown, withthe middle line containing the sought string. TheVHST prompt is re-displayed to allow morecommand use. If the string is not found, VHST isreprompted to allow more command use.

FIND Repeats the previous forward search

HELP List valid responses

NEXT BOT Moves to the end of the file




LD 22

NEXT x Move forward x lines in the History File, display alllines in between.

This command can be used to view lines forward,toward the end of the file. The lines between thecurrent index location, and the new one (x linesdown) are displayed.

If you enter only NEXT, the default of 20 lines isused for the move. When the move is complete,VHST is reprompted to allow more command use.

PREV TOP Moves to the top of the file

PREV x Move backward x lines in the History File, display alllines in between

This command can be used to view lines backward,toward the top of the file. The lines between thecurrent index location, and the new one (x lines up)are displayed.

If you enter only PREV, the default of 20 lines isused for the move. When the move is complete,VHST is reprompted to allow more command use.

TRF View the system traffic log file

TTYLOG n View the log file for TTY port n

UP TOP Moves to the top of the file

UP Move backward 6 lines in the History File

This command can be used to move backward inthe History File, toward the top. If x exceeds the topof the file, the top will be shown. When the move iscomplete, VHST is reprompted to allow morecommand use.


Page 126 of 500 Alphabetical list of commands


LD 32

Alphabetical list of commands

Command Description Pack/Rel

CDSP Clear the maintenance display on active CPU to 00 or blank. basic-1

CMIN Clear the minor lamp on a system basis. alrm_filter-22

CMIN ALL Clear minor alarm indication on all attendant consoles. basic-1

CONV tn Convert packed TN (in hex) to l s c u, or vice versa. xpe-15c u Option 11C format

CONV tn Convert packed TN (in hex) to l s c u xpe-15l s c u Convert packed TN (in hex) to tn

The command format is:

• CONV tn - convert packed TN• CONV l s c u - convert unpacked TN

Where:

• l = 0-255, Option 81C with Fiber Network Fabric fnf-25

CPWD l s c uc u

Reset or Clear directory password for M3000 set.Option 11C format

Allows the M3000 Directory password of the specified M3000set to be reset to default (12345678). This allows a user toaccess the M3000 Directory if the password has beenforgotten or if the user wants to change the current password.Applies to M3903, M3904, M3905, and i2004.

basic-24

itg-25For M3900 Phase 3 terminals the Directory password iscleared.Where:

• l = 0-255, Option 81C with Fiber Network Fabric fnf-25

DIS AUTO l s c u Disable automatic link recovery option of a DSL bri-18c u Option 11C format

DISC (appl) c Disable application on Multi-purpose ISDN SignalingProcessor (MISP). (Option 11C).

Where: appl =BRIL (Basic Rate Interface Line), BRIT (BasicRate Interface Trunk), or BRIE (UIPE Basic Rate InterfaceTrunk)

bri-18

Alphabetical list of commands Page 127 of 500

Maintenance

LD 32

DISC (appl) c REM bri-18Disable and remove application from Multi-purpose ISDNSignaling Processor (MISP). (Option 11C)

Where: appl =BRIL (Basic Rate Interface Line), BRIT (BasicRate Interface Trunk), or BRIE (UIPE Basic Rate InterfaceTrunk)

DISC (BASE) l s c Disable specified BRSC card or to disable the ISDN BasicRate Interface Signaling Concentrator (BRSC) card.

Where:

• BASE = Disable only the basecode. If not specified,both the basecode and application are disabled. Theapplication is disabled first unless BASE is entered.

bri-18

The card faceplate LED is turned on to indicate the card isdisabled, and the IPC channel is eliminated. The “.” prompt isgiven when the process is complete.

DISC BRI l s c Disable the BRSC ISDN BRI application.

All active and transient ISDN BRI calls are dropped, and allsignaling and packet channels are torn down. The DSLsoftware state remains the same, but the ISDN BRI line cardsreceive a disable message.

bri-18

DISC c Disable specified DTR/MFR card. (Option 11C)

This command is also used for Multi-purpose ISDN SignalingProcessor (MISP).

If BRI reference clock source is configured on this SILC theuser will be prompted with:

CLOCK SOURCE ON DSL #, PROCEED? ,

where # = unit 0-7

For Option 11C: DISC 0 disables all configured units oncard 0

basic-1

DISC l s c Disable specified peripheral card.



where # = unit 0-7

basic-1



LD 32

DISI c Disable specified card when it is idle. (Option 11C)



where # = unit 0-7

basic-1

DISI l s c Disable specified card when it is idle.

Where:

• l = 0-255, Option 81C with Fiber network Fabric



Where: # = unit 0-7

basic-1

fnf-25

DISL (appl) l Disable application on MISP loop. Where appl =

• BRIL (Basic Rate Interface Line), or• BRIT (Basic Rate Interface Trunk)

bri-18

DISL (appl) l 1 Disable MISP loop.

Where: appl =BRIL (Basic Rate Interface Line), BRIT (BasicRate Interface Trunk), or BRIE (UIPE Basic Rate InterfaceTrunk).

Applicable if SUPP package 131 is not equipped.

bri-18

DISL (appl) l 1 Disable MISP application and loop. Where:

• appl = optional application name (BRIL)• 1 = force download the application

bri-18

DISL (appl) l REM bri-18Disable and remove application from Multi-purpose ISDNSignaling Processor (MISP). Applicable if SUPP package 131is equipped.

DISL l Disable network loop. See “Using the Enable/Disablecommands” in the introduction. This command is also usedfor superloops and MISPs.

basic-1


Maintenance

LD 32

DISL sl Disable specified superloop. Active calls on the superloop willbe disconnected and line transfer will occur at the remoteend.

basic-21

DISN l Disable network card containing specified loop, where “loop”is the number of the even or odd loop. Not applicable tosuperloops.

DISR l s c u Disable specified DTR/MFR card or unit. The LED should belit on the XMFR card in response to this command.

basic-21

DISS l s Disables specified shelf. See “Using the Enable/Disablecommands” in the introduction.

basic-1

DISS m Disables specified module. Where: m = 0 for Main or m = 1-4for Expansion module. (Option 11C) See “Using theEnable/Disable commands” in the introduction.

basic-1

DISU BRI l s c Disable ISDN BRI BRSC card. brit-19

DISU c d Disable specified Digital Subscriber Loop (0-7). (Option 11C).

If BRI reference clock source is configured on the DSL, theuser will be prompted with:

CLOCK SOURCE ON THIS DSL, PROCEED?

bri-18

DISU c u Disables specified unit. See “Using the Enable/Disablecommands” in the introduction. (Option 11C)

For Option 11C: 0-15 may be accepted as input for card 0.

basic-1

DISU l s c d Disable specified Digital Subscriber Loop 0-7.

If BRI reference clock source is configured on the DSL theuser will be prompted with:

CLOCK SOURCE ON THIS DSL, PROCEED?

bri-18

DISU l s c u Disable specified unit. See “Using the Enable/Disablecommands” in the introduction.

basic-1

DLIF c Download a UIPE BRI trunk interface data file to MISP card(Option 11C).

bri-18



LD 32

DLIF l x Download an UIPE BRI trunk interface data file to a MISPloop. The MISP specified must have the BRIT UIPE loadwareapplication. Where x may be:

• (0) = UIPE SL1• 1 = ETSI QSIG• 2 = ISO QSIG• 28 = ETSI QSIG GF• 29 = ISO QSIG GF

To achieve a successful download:

1. the MISP basecode must be enabled2. the specified MISP must have the UIPE BRI trunk

loadware configured3. the interface must be inactive (interpret this to mean

that either the UIPE BRI trunk application must bedisabled or no DSL of this interface type can beenabled)

QSIG package 263 is required to have ETSI and ISO options.

bri-18

DSCT l Disable automatic background continuity tests for asuperloop.

Where:

• loop = 0-252 and must be a superloop (multiples of 4),Option 81C with Fiber Network Fabric

xpe-15

fnf-25

DSIF L PDL2 l s c Disables the SAPI 16 interface number for BRSC on l s c forthe MPH on loop L.

bri-19

DSIF L PDL2 L1 Disables SAPI 16 interface number for BRIL on Loop L1 forMPH on loop L.

bri-19

DSIF l s c DSL BCH xDisables the link interface for B-channel x for DSL l s c bch.Where: x = 1–2

bri-19

DSIF l s c DSL DCH xDisables the link interface number for USID x for the DSL onl s c dch.

bri-19

DSIF l PDNI Y Disable the link interface number Y for PDNI on Loop Y (1-3) bri-19


Maintenance

LD 32

DSNW l Disable network card containing specified loop, where “loop”is the number of the even or odd loop. Not applicable tosuperloops.

basic-1

DSPS x Disables Peripheral Signaling (PS) card x and loops servicedby the card.

Where:

• x = 0-9, Option 51C, 61C

• x = 0-15, Option 81C with Fiber Network Fabric

Disabling PS card 0 interrupts service on loops 0 to 15. Tore-enable the card, use the ENPS x command.

If this fails, a system initialization may be required. Use thedisable command with discretion. Disabling a PS carddisables up to 16 loops.

basic-1

fnf-25

The following lists the group/PS/loop relationship:

Group PS Loops

0 0 0 to 150 1 16 to 311 2 32 to 471 3 48 to 632 4 64 to 792 5 80 to 953 6 96 to 1113 7 112 to 1274 8 128 to 1434 9 144 to 1595 10 160 to 1755 11 176 to 1916 12 192 to 2076 13 208 to 2237 14 224 to 2397 15 240 to 255

DSRB c d Disable Remote Loop Back for specified BRI Trunk DSL(Option 11C)

bri-18

DSRB l s c d Disable Remote Loop Back for specified BRI Trunk DSL bri-18

DSTS c d Disable Remote Loop Back test mode for specified BRI TrunkDSL (Option 11C)

bri-18



LD 32

DSTS l s c d Disable Remote Loop Back test mode for specified BRI TrunkDSL

bri-18

DSXP x Disable Controller x and all connected cards. xpe-15

ENCT l Enable automatic background continuity tests for loop. xpe-15Where:

• loop = 0-159• loop = 0-252 and must be a superloop (multiples of 4),

Option 81C with Fiber Network Fabricfnf-25

END Abort current test. Stops outputting. Stops current test. basic-1

ENIF L PDL2 l s c Enables the SAPI 16 interface number for BRSC on l s c forMPH on loop L.

bri-19

ENIF l s c DSL BCH xEnables the link interface for B-channel x for DSL l s c bch.Where: x = 1–2

bri-19

ENIF l s c DSL DCH xEnables the link interface number for USID x for the DSL onl s c dch.

bri-19

ENIF l PDNI Y Enables the link interface number Y for PDNI on Loop Y (1-3). bri-19

ENL AUTO c d Enable automatic link recovery option of a DSL (Option 11C) bri-18

ENL AUTO l s c u Enable automatic link recovery option of a DSL. bri-18

ENLC (appl) c Enable specified application on Multi-purpose ISDN SignalingProcessor (MISP) card. (Option 11C). Where:

• appl = optional application name BRIL (Basic RateInterface Line) or BRIT (Basic Rate Interface Trunk)

bri-18

ENLC (appl) c FDL bri-18Enable and force download loadware for specified applicationon Multi-purpose ISDN Signaling Processor (MISP) card.(Option 11C). Where appl =

• BRIL (optional application name: Basic Rate InterfaceLine), or

• BRIT (Basic Rate Interface Trunk)


Maintenance

LD 32

ENLC (BASE) l s c (FDL/NST) brit-19Enable specified card.

If the card resides on a disabled shelf, the status is output andenable is not performed. If card has been disabled byoverload, the overload status entry is cleared.

Used to enable the ISDN Basic Rate Interface SignalingConcentrator (BRSC) card. The command format is shownhere. ENLC (BASE) l s c u (FDL/NST)

Where:

• BASE = enable only the BRSC basecode. If notspecified, both the basecode and the application will beenabled.

• l = loop• s = shelf• c = card• FDL = force download the basecode• NST = No self-test

The card faceplate is turned off to indicate the card isenabled, and the IPC channel is built.

ENLC BRI l s c (FDL) brit-19Enable the BRSC ISDN BRI application. Where:

• BRI = the BRSC ISDN BRI application• l = loop• s = shelf• c = card• FDL = force download the application

The application is force downloaded if:

• FDL is entered, or• No application currently exists on the BRSC card, or• There is a version number mismatch between the

applications in the software and on the card.



LD 32

ENLC c Enable and reset specified DTR/MFR card. (Option 11C)


This command is also used for Multi-purpose ISDN SignalingProcessor (MISP)., S/T-Interface (SILC), and U-Interface(UILC) line cards.

This command causes the card to perform a self test. If thecard self test passes, the LED will blink 3 times. If it fails, theLED will be lit solidly. A XMI message will be issued toindicate that the XMFR card has powered up. This commandcan be used to enable a XMFR card.

ENLC 0 enables all units (0-15) on TDS card 0 if enabled. TheTDS card can be enabled by entering the command ENLX 0in LD 34.

basic-1

ENLC c FDL Enable Multi-purpose ISDN Signaling Processor (MISP) andforce download basecode.(Option 11C)

bri-18

ENLC l s c Enable and reset specified peripheral card.


This command causes the card to perform a self test. If thecard self test passes, the LED will blink 3 times. If it fails, theLED will be lit solidly. A XMI message will be issued toindicate that the XMFR card has powered up. This commandcan be used to enable a XMFR card.

This command is also used for the S/T-Interface (SILC) andU-Interface (UILC) line cards.

basic-1

ENLG x Enable group x. Equivalent to two ENPS commands. Refer toDSPS command for the relationships of groups, PS cards andloops.

Where:

• x = Group 0-7, Option 81C with Fiber Network Fabric

basic-1

fnf-25

ENLL (appl) l Enable specified application on Multi-purpose ISDN SignalingProcessor (MISP) loop. Where appl =

• BRIL (Basic Rate Interface Line) or• BRIT (Basic Rate Interface Trunk)

bri-18


Maintenance

LD 32

ENLL (appl) l 1 bri-18Enable MISP application, and loop. Where:

• appl = optional application name (BRIL)• loop = loop number• 1 = force download the application

ENLL (appl) l FDL bri-18Enable and force download loadware for specified applicationon Multi-purpose ISDN Signaling Processor (MISP) loop.Applicable if SUPP package 131 is equipped.

ENLL (appl) l 1 bri-18Enable MISP loop. Where:

• appl = optional application name (BRIL)• 1 = force downloads the application

• Applicable if SUPP package 131 not equipped.

ENLL l Enable network loop.

See “Using the Enable/Disable commands” in theintroduction. This command is also used for Multi-purposeISDN Signaling Processors (MISP).

basic-1

ENLL l FDL Enable MISP and force download basecode. bri-18

ENLL l (v) Enable superloop, download peripheral software version v. Ifversion v is not specified, the software downloaded is current(c) or latest (l) version as defined in LD 97.

xpe-15

ENLL sl Enable specified Superloop. OK is output if the operation issuccessful.

basic-21

ENLN l Enable network card with specified loop, where loop is theeven or odd numbered loop on the network card. Notapplicable to superloops.

ENLR c u Enable the specified DTR/MFR card. (Option 11C)

Meridian 1 software will issue a message to request XMFR toperform an echo test only when ENLR is issued to enable theXMFR card.

basic-21



LD 32

ENLR l s c u Enable the specified DTR/MFR card.

Meridian 1 software will issue a message to request XMFR toperform an echo test only when ENLR is issued to enable theXMFR card.

basic-21

ENLS l s Enable specified shelf. Where: l = loop and s = shelf. If theshelf is disabled by overload, the overload status entry iscleared.

basic-1

ENLS m Enable the specified module. (Option 11C). Where: m = 0 forbase module or m = 1-4 for expansion module. If the moduleis disabled by overload, the overload status entry is cleared.

basic-1

ENLU c d Enable Digital Subscriber Loop (0-7) (Option 11C) bri-18

ENLU c u Enable specified unit. (Option 11C)

ENLU c u accepts units 0-15 as input. Units can only beenabled if TDS 0 is enabled.

For Option 11C: For Slot 0, the TDS must first be enabled byentering the command ENLX 0 in LD 34.

basic-1

ENLU l s c d Enable Digital Subscriber Loop (0-7). bri-18

ENLU l s c u Enable specified unit.

If the unit resides on a disabled shelf or card, the status isoutput and enable is not performed. If the unit to be enabled isa 500/2500 message waiting telephone, test the unit prior toenabling.

basic-1

ENNW l Enable network card with specified loop, where loop is theeven or odd numbered loop on the network card. Notapplicable to superloops.

basic-1

ENPS x Enables PS card x and all loops that were enabled at time oflast DSPS command. Refer to DSPS command to find therelationships of groups, PS cards and loops.

Where:

• x = 0-15, Enable PS card and clear PBX_LAMPBADBITS for Option 81C with Fiber Network Fabric

basic-1

fnf-25

ENRB c d Enable Remote Loop Back for specified BRI Trunk DSL.(Option 11C)

bri-18


Maintenance

LD 32

ENRB l s c d Enable Remote Loop Back for specified BRI Trunk DSL. bri-18

ENTS c d Enable Remote Loop Back test mode for specified BRI TrunkDSL. (Option 11C)

bri-18

ENTS l s c d Enable Remote Loop Back test mode for specified BRI TrunkDSL.

bri-18

ENXP x (v) Enable Controller x and associated PE cards, downloadsoftware version v.

Enable all PE cards connected to Controller x and theController itself. If version v is not specified, the softwaredownloaded to the Controller is current (c) or latest (l) versionas defined in LD 97.

xpe-15

ENXP XPC x (v) Enable Controller x, do not enable the associated PE cards,download software version v.

The cards connected to the Controller are not enabled by thiscommand. If version v is not specified, the softwaredownloaded to the Controller is current (c) or latest (l) versionas defined in LD 97.

xpe-15

ESTU c d Establish D-channel link for the specified Digital SubscriberLoop (0-7). (Option 11C)

bri-18

ESTU l s c d Establish D-channel link for the specified Digital SubscriberLoop (0-7).

bri-18

FDIS NCAL <c DSL#> <conn_id> qsig gf-22Force disconnect the specified call-independent connection(as defined by its connection ID number)

Note that the command format for an Option 11C is:

STAT NCAL <c 0 0 DSL#><conn_id#>

FDIS NCAL <l s c DSL#> <conn_id> qsig gf-22Force disconnect the specified call-independent connection(as defined by its connection ID number)

FDLC Cancel or stop the sytem wide flash download for M39xxunits. Units include: M3902, M3903, M3904 and M3905.

arie- 25



LD 32

FDLF l s c u Initiate forced download to one M39xx unit regardless ofversion or state. Units include: M3902, M3903, M3904 andM3905.

arie- 25

FDLI l s c u Initiate conditional download to one M39xx unit regardless ofversion or state. Units include: M3902, M3903, M3904 andM3905.

arie- 25

FDLU l s c u Initiate conditional download to one M39xx unit. Units include:M3902, M3903, M3904 and M3905.

arie- 25

FDLS xxxx Intiate system wide flash download to all or specified type ofM39xx units according to parameters specified in Overlay 97FDL configuration.

Where xxxx = M3902, M3903, M3904, M3905, ALL andNOW.

arie- 25

FSUM Print summary report of firmware versions currently on M39xxunits. Units include: M3902, M3903, M3904 and M3905.

arie- 25

FSUM ALL Print complete report of all M39xx sets based on parametersspecified in LD 97.

arie-25

FWVU l s c u Query and print the firmware versions currently on M39xxterminal

arie- 25

IDC c Print MISP or XPE card ID. (Option 11C)

The MISP card ID output format is:

• CARDID: xxx. . . x• BASECODE VERSION: xxx. . . x• BRI LINE/TRUNK VERSION: xxx. . . x• BOOTCODE VERSION: xxx. . . x



bri-18

IDC l Print ID of Network and Peripheral Controller

Where:

• l = 0-252 and must be a superloop (multiple of 4),Option 81C with Fiber Network Fabric

fnf-25


Maintenance

LD 32

IDC l s c Print BRSC card and loadware version.

This command, queries the BRSC card ID, the basecode, andthe application version number. Where: l = loop, s = shelf, andc = card.

Output example:

• BOOTCODE VERSION xx . . . x• BASECODE VERSION xx . . . x• BRI APPL VERSION xx . . . x

brit-19

IDC l s c Print MISP or XPE card ID.



The XPE card ID output format is:

=> XXXX CCCCCCCC-RRSSSS

bri-18

Where:

• XXXX = card type (i.e., XDTR, XUT, etc.)• CCCCCCCC = order code• RR = release number• SSSS = is the serial number

IDC l s c d Print ID of Digital Subscriber Loop 0-7. bri-18



LD 32

IDC sl For Copper Connections xpe-15

Print Network ID and Controller for a superloop.

Output format for superloop card ID:

XNET VERS => xxxRUNNING FROM yyyFW IS SANE

CCCCCCCC-RRSSSS

XPEC0 VERS => xxxRUNNING FROM yyyFW IS SANE

XPECz CCCCCCCC-RRSSSS

XPEC1 VERS => xxxRUNNING FROM yyyFW IS SANE

XPECz CCCCCCCC-RRSSSS

Where:

• xxx = loadware version• yyy = RAM or ROM• z = 2 or 4• CCCCCCCC = order code• RR = release number• SSSS = is the serial number

IDC sl For Carrier Connections

Get card id of Local Carrier Interface (LCI) superloop and itsassociated Remote Carrier Interface (RCI).

Output format for LCI superloop card ID:

LCI VERS => xxxFW IS SANEaaaaaaaaaaaa

Output format for RCI superloop card ID:

XPEC VERS=>xxxFW IS SANEaaaaaaaaaaaa

Where:

• xxx = loadware version• aaaaaaaaaaaa = contents of ID EEPROM (LCI or

RCI)

rem_ipe-21


Maintenance

LD 32

IDC sl For Fibre Connections rem_ipe-22

Print card ID of optical packets and main boards for Fibresuperloop and associated Controller(s)

The output format for the superloop card ID including opticalpackets is:

FNET VERS => xxxFW IS SANE

aaaaaaaaaaaaaPRIM: ppppppppSEC: ssssssss

XPEC VERS => xxxFW IS SANE

aaaaaaaaaaaPRIM: ppppppppSEC: ssssssss

Where:

1. xxx = loadware version2. aaaaaaaaaaaaa = contents of ID EEPROM (FNET

or FPEC)3. PRIM: pppppppp = contents of ID EEPROM primary

packet (if present)4. SEC: ssssssss = contents of ID EEPROM secondary

packet (if present)

IDC l s c Print card ID for PE card. The format is:

IDC l s c — print ID of specified line card

The format of the card ID is CCCCCCCC-RRSSSS, where:

• CCCCCCCC = order code• RR = release number• SSSS = serial number

xpe-15

For example, a Network Card (NT8D04AA) with a release of01 and serial number of 00001 will have a card ID with:NT8D04AA-010001

For BRI MISP cards, the output is:

• CARDID: xxx...x• BASECODE VERSION: xxx...x• BRI LINE/TRUNK VERSION: xxx...x• BOOTCODE VERSION: xxx...x



LD 32

IDCS x Print card ID for all cards on shelf controlled by Controller x.The card ID for all cards in shelf controlled by Controller x isoutput. The XPE card ID output format is:

=> XXXX CCCCCCCC-RRSSSS

Where:

• XXXX = card type (i.e., XDTR, XUT, etc.)• CCCCCCCC = order code• RR = release number• SSSS = is the serial number

xpe-15

IDU c d Print set ID for Digital Subscriber Loop d (0-7) (Option 11C) bri-18

IDU l s c d Print set ID for Digital Subscriber Loop d (0-7) bri-18c u Option 11C format

IDU l s c u Print set ID. Print ID applies to the following set types: M2006,M2008, M2016, M2216 and M2616.

The output format of the set ID (M2008 for example) is:

• ARIES TN: l s c u• TN ID CODE: M2008• NT CODE: NT2K08WC• COLOR CODE: xx• RLS CODE: xx• SER NUM xxxxxx

The color codes are:

• 03 is black

• 35 is chameleon ash

• 93 is dolphin grey

xpe-15

LBD l s List TN of all PBX units on specified shelf, with lamps flaggedas defective.

fnf-25

LBSY l s List TNs of all busy units on specified shelf. basic-1

LBSY m List TNs of all busy units in specified module. (Option 11C).Where: m = 0 for Base module or 1 for Expansion module.

basic-16

LDIS l s List TNs of all disabled units on specified shelf. basic-1


Maintenance

LD 32

LDIS m List TNs of all disabled units on specified module. (Option11C). Where: m = 0 for Base module or 1 for Expansionmodule.

basic-16

LIDL l s List TNs of all idle units on specified shelf. basic-1

LIDL m List TNs of all idle units in specified module. (Option 11C).Where: m = 0 for Base module or 1 for Expansion module.

LMNT l s List TNs of all maintenance busy units on specified shelf. basic-1

LMNT m List TNs of all maintenance busy units on specified module.(Option 11C). Where: m = 0 for Base module or m = 1 forExpansion module.

MFR c Test all MFR units on card c

During the MFR test, faulty MFR/XMFR cards are disabledand MFRxxx error messages are output.

basic-21

MFR c u Test specified MFR card or unit.


basic-21

MFR l s c u Test specified MFR card or unit.


basic-21

MFR l Test all MFR units on loop l


basic-21

MFR <cr> Test all MFR units


basic-21

PBXH Message Waiting lamp maintenance. basic-1

PBXT (c u), ALL Tests 500/2500 Message Waiting lamp on specified card orunit. This is required after failed lamp is fixed. (Option 11C)

basic-1



LD 32

PBXT ALL Test all Message Waiting lamps on 500/2500 telephones onall loops

Where:

ALL = loops 0-255, Option 81C with Fiber Network Fabric

basic-5

fnf-25

PBXT l (s c u) Tests 500/2500 Message Waiting lamp on specified loop,shelf, card or unit. This is required after failed lamp is fixed.

basic-5

PCON c d Upload and print configuration and LAPD parameters forspecified DSL. (Option 11C)

bri-18

PCON l s c d Upload and print configuration and LAPD parameters forspecified DSL. This command requires the specified DSL tobe configured for the BRI Trunk Application. See examplebelow:

PCON 6 0 0 6.DSL: 6 0 0 6 LINL PARAM CONFIRM TIME: 0:02:10INTERFACE: SL-1OPER MODE: USRT200: 2T203: 20N200: 3N201: 260K: 1PROT #: 1

bri-18

PERR (appl) c Upload and print Layer 2 error log for specified SILC, UILC orMISP card. (Option 11C)

Where (appl):

• BRIE for UIPE Basic Rate Interface Trunk

• BRIT for NON-UIPE Basic Rate Interface Trunk

bri-18

PERR (appl) l Upload and print Layer 2 error log for specified MISP.

Where (appl):



bri-18


Maintenance

LD 32

PERR (appl) l s c Upload and print Layer 2 error log for specified SILC or UILC.This command requires the specified MISP or line card to beconfigured for the BRIT Application.

Where (appl):



bri-18

If error log is requested for a line card the error log for eachDSL is printed. If error log is requested for a MISP theapplication global log is also printed.Interpretation of error logs:

1st byte is DSL number or “80” for Application log.2nd byte is number of non-zero logs.

If errors were logged the subsequent information is printed foreach error type:

• 3rd byte is counter type code• 4th byte is “HIGH” byte of count• 5th byte is “LOW” byte of count

Examples follow :

PERR brie 6

.DSL: 6 0 0 6 ERR LOG CONFIRM TIME: 0:02:10

00 00 01 00 06 00 07 00

^ ^ ^ ^

DSL 0 DSL 1 DSL 6 DSL 7 (no errorsfor all DSLs)

PERR brie 3

.DSL: 5 0 0 2 ERR LOG CONFIRM TIME: 0:02:10

80 01 4D 00 09

Where:

• 1st byte - 80 - indicates Application global log• 2nd byte - 01 - is number of error logs• 3rd byte - 4D - is counter type code• 4th bye - 00 - is “HIGH” byte count• 5th byte - 09 - is “LOW” byte counts for all DSLs

PLOG c d Upload and print protocol log for specified BRI Trunk DSL.(Option 11C)

bri-18



LD 32

PLOG l s c d Upload and print protocol log for specified BRI Trunk DSL.The protocol log keeps record of up to 32 protocol types. Onlynon-zero counters are uploaded and printed.

This command requires the specified MISP or line card to beconfigured for the BRIT Application. See example below:

PLOG 6 0 0 6

.DSL: 6 0 0 6 PROTOCOL CONFIRM TIME: 0:02:10

17 117 <--Counter 17 shows 117 SABME framesreceived with incorrect C/R bit

18 141 <--Counter 18 shows 141 supervisoryframes received with F=1

19 84 <--Counter 19 shows 84 unsolicited DMresponses with F=1

bri-18

PMES c d Upload and print Layer 3 message log for specified DSL.(Option 11C)

bri-18

PMES l s c d Upload and print Layer 3 message log for specified DSL. Thiscommand requires the specified DSL to be configured for theBRI Trunk Application.

Each time a valid Layer 3 message is received by the MISP, acounter for that particular message is incremented. The logkeeps track of up to 20 message types.

Only non-zero items are uploaded and printed. Making trunkcalls will create a printable log. In the following example, 2calls were made:

bri-18

PMES 6 0 0 6

.DSL: 6 0 0 6 MSG LOG CONFIRM TIME: 0:02:10

ALERT: 2PROC: 2CONNECT: 2DISCONN: 2REL COP: 2

PTAB c d Upload and print Layer 3 Message configuration IE table forspecified BRI trunk DSL. (Option 11C)

bri-18


Maintenance

LD 32

PTAB l s c d Upload and print Layer 3 Message configuration IE table forspecified BRI trunk DSL. PTAB uploads what wasdownloaded when the Application was enabled.

bri-18

PTAB c d <tbl #> Upload and print specified Layer 3 Message configuration IEtable for specified BRI trunk DSL.Where: <tbl #> = table number. (Option 11C)

bri-18

PTAB l s c d <tbl #> bri-18Upload and print specified Layer 3 Message configuration IEtable for specified BRI trunk DSL. PTAB uploads what wasdownloaded when the Application was enabled.Where: <tbl #> = table number.

PTRF c d Upload and print traffic report for specified BRI Trunk DSL.(Option 11C)

The following traffic information is output:

CONNECTED NCALLS : Total number of establishedcall-independent connections

bri-18

PTRF l s c d Upload and print traffic report for specified BRI Trunk DSL.This command requires the specified DSL to be configuredfor the BRI Trunk Application. See example below:

bri-18

PTRF 6 0 0 6

.DSL: 6 0 0 6 TRAFFIC CONFIRM TIME: 0:02:10

PEAK_I_US: 0 <-- Peak link usage (over a 5 second period)for incoming traffic since the last time the traffic data wasuploaded. An integer 0 - 100 which represents the percentageof the link capacity used.

AVRG_I_US: 0 <-- Average link usage for incoming trafficsince the traffic was last uploaded.

PEAK_O_US: 0 <-- Peak link usage (over a 5 second period)for outgoing traffic since the last time the traffic data wasuploaded. An integer 0 - 100 which represents the percentageof the link capacity used.

AVRG_O_US: 0 <-- Average link usage for outgoing trafficsince the traffic was last uploaded.

TIME: 0 <-- time since last traffic upload queryCONNECTED CALL: 2 <-- number of successfullyconnected trunk calls



LD 32

RLBT c d Perform Remote Loop Back Test on specified BRI Trunk DSL.(Option 11C)

bri-18

RLBT l s c d Perform Remote Loop Back Test on specified BRI Trunk DSL. bri-18

RLSU c d Release D-channel link for specified Digital Subscriber Loop(0-7). (Option 11C)

bri-18

RLSU l s c d Release D-channel link for specified Digital Subscriber Loop(0-7).

bri-18

RMIF L PDL2 l s c Disables and removes the SAPI 16 interface number forBRSC on l s c for MPH on loop L.

bri-19

RMIF L PDL2 L1 Disables and removes the SAPI 16 interface number for BRILon Loop L1 for MPH on loop L.

bri-19

RMIF l s c DSL BCH x bri-19Disables and removes the link interface for B-channel x forDSL l s c bch; where: x = 1–2

RMIF l PDNI Y Disables and removes the link interface number Y for PDNIon Loop Y (1-3)

bri-19

SDLC l s c Get status of specified ISDLC card. basic-7

SDTR c u List status of specified DTR/MFR card or unit. basic-21

SDTR l s c u List status of specified DTR/MFR card or unit. basic-21

SDTR <cr> List status of all disabled DTR/MFR units basic-21

STAT Get status of all configured loops in system basic-1

STAT (appl) c Get status of MISP card and application. (Option 11C) SeeSTAT (appl) loop for possible responses.

bri-18

STAT (c) Get status of all cards or (specified card). (Option 11C) SeeSTAT (loop) and STAT l s c for possible responses.

STAT 0 provides the status of TDS 0 and units 0-15 for card 0.

basic-1

STAT c d Get status of specified DSL. (Option 11C) bri-18See STAT l s c d for possible responses.


Maintenance

LD 32

STAT c u Get status of specified unit. (Option 11C) See STAT l s c ucommand for possible responses.

STAT c u accepts units 0-15 as input for card 0.

basic-1

STAT (appl) l Get status of MISP loop and application.

If appl = BRIL, the status of the BRI Line application is output.If appl = BRIT, the status of the BRI Trunk application isoutput.

Typical response is:

loop = MISP loop for non-Option 11Cmm DSBL nn BUSYMISP lll : ENBL ACTIVATED timestampBRIL : ENBLBRIT : ENBL

If the card has been manually disabled, the response is:

loop = MISP loop for non-Option 11CDISABLED RESPONDINGMAN DSBL

bri-18

If the card has been disabled by the system, the response is:

loop = MISP loop for non-Option 11CDISABLED RESPONDINGSYS DSBL - aaa...a

Where aaa...a is the reason as follows:

a BOOTLOADING = basecode is being downloaded tothe MISP

b FATAL ERROR = MISP has a serious problemc OVERLOAD = MISP overload (card inoperable)d RESET THRESHOLD = too many resets (card

inoperable)e SELF TESTING = card is performing self-testf SELFTEST FAILED = self-test failedg SELFTEST PASSED = successfully completed

self-testh SHARED RAM TEST FAILED = MISP memory

problem (card inoperable)i STUCK INTERRUPT = MISP hardware failure

(replace card)



LD 32

With the STAT BRIL or STAT BRIT option, the response isone of the following:

1. APPLICATION ENBL

2. APPLICATION NOT CONFIGURED

3. APPLICATION NOT RESPONDING

4. APPLICATION MAN DSBL (manually disabled)5. APPLICATION SYS DSBL - aaa..a (system

disabled)

Where: aaa...a is the reason as follows:

a CLOSED = application is closed by basecode on thecard

b CLOSED ERR = error in closing the applicationc CORRUPTED = application is corrupted on the cardd DOWNLOADING = application is being downloadede ENABLED = application is in active statef INACTIVE = application is in inactive stateg MNT BUSY = application is in maintenance busy

stateh WAIT DSBL = application is in process of being

disabledi WAIT ENABLE = application is in process of being

enabledj WAIT ERASE = application is being erased from the

cardk WAIT REMOVE = application is being removed from

the card

STAT (l) Give status of one or all loops. Response is one of thefollowing:

1. x BUSY, y DSBL = loop enabled with x channels busyand y channels disabled.

2. UNEQ = loop unequipped.3. CTYF: l1 l2 = loop specified in STAT command is

unable to receive data from loops l1, l2, etc. (i.e.,continuity test failed in most recent LD 45 loop test).Probable fault in network card.

4. DSBL: NOT RESPONDING = loop disabled. Networkcard not responding. Card missing, disabled by switchor faulty.

basic-1


Maintenance

LD 32

5. DSBL: RESPONDING = loop disabled but the networkcard responds. loop may have been disabled due to:

a manual request (DISL)b associated Peripheral Signaling card being disabledc overload condition on associated loop

Note 1: Overload conditions are indicated by OVD messages. Anattempt to enable a loop which was disabled due to overload mayresult in a recurrence of the overload condition: the system's servicemay be impaired for about 2 minutes.

Note 2: For MISP loops see STAT (appl) loop command.

STAT l s Get idle, busy or disabled status of units on specified shelf.Displays number of units idle, busy, disabled andmaintenance busy for the specified shelf.

basic-1

STAT l s c Get status of any specified PE/IPE card. (e.g., digital line,analog, DTR, etc.)

When getting the status of a card relating to a trunk error(STAT), the term RVSD may appear with the trunkinformation. RVSD indicates that the software has detected areversed wired trunk for that unit.

When getting the status of a card where ACD sets aredefined, the printout will include MSB LOG OUT, MSB LOGIN, LOG IN, OR LOG OUT, according to the ACD set state.

The output format for either a S/T-Interface line card (SILC) oran U-Interface line card (UILC) is:

For BRI trunks:

ll = UNIT ll = DSL/UNIT number on the card =

swstate type L2_state L1_state dch_state clk(mode)

bri-18

For BRI lines:

ll = UNIT ll = DSL/UNIT number on the card =

swstate type L2_state L1_state

If you are analyzing a SILC or an UILC card, Table 14 onpage 153 lists and defines output fields and field responses.An output example can be found page 152.



LD 32

Output Example:

00 = UNIT 00 = IDLE LINE ESTA UP01 = UNIT 01 = IDLE TRNK ESTA UP ESTA SREF (TE)02 = UNIT 02 = IDLE LINE ESTA DOWN03 = UNIT 03 = UNEQ04 = UNIT 04 = UNEQ05 = UNIT 05 = UNEQ06 = UNIT 06 = DSBL TRNK DSBL UNEQ RLS (NT)

7 = UNIT 07 = DSBL TRNK DSBL UNEQ RLS (TE)

The output format for an ISDN BRI card is:

loop = UNIT sw_state DSL misp_state LC_state

With ISDN BRI BRSC cards, the basecode and applicationstatus are output.

brsc/basic-19

APPLICATION MAIN STATE SUB STATE/ACTIVATIONTIME

+---------------------+------------------------+---------------------------------------+BASECODE ENABLED xx/xx/xx x:xxBRI ENABLED xx/xx/xx x:xx

+---------------------+-------------------------+--------------------------------------+IDLE 0 BUSY 0 DISABLED 8

MSBY 0TOTAL DSLS CONFIGURED 8

If you are analyzing an ISDN BRI card , see “STAT l s c d”command for a list of possible states.


Maintenance

LD 32

Table 14: STAT l s c Field and Response Definitions

Field Field Definition Response Response Definition

swstate state of DSL/UNIT insoftware

IDLE no active callBUSY active with a callUNEQ unequippedMBSY maintenance busy

type DSL type LINE BRI lineTRNK BRI trunk

L2_state Layer 2 state of DSL/UNIT inMISP loadware

UNEQ unequippedIDLE no active callBUSY active with a callMBSY maintenance busyDSBL disabledESTA D-channel link is establishedRLSU D-channel link is releasedTEST test modeRLBT remote loop backAPDB application disabledMPDB associated MISP disabledMPNR associated MISP not respondingUTSM unable to send message to MISP

L1_state Layer 1 state of line card UNEQ unequippedDOWN Layer 1 is downLCNR line card not respondingUP Layer 1 is upUNDN undefined DSL stateXPDB Associated XPEC is disabledUTSM unable to send message to MISP

dch_state State of D-channel link insoftware

ESTA D-channel link is establishedRLSU D-channel link is releasedTEST-IDLE test mode idleTEST-RLBT test mode remote loop back

clk Clock mode DSBL disabledPREF primary referenceSREF secondary reference

mode Layer 1 mode of DSL NT Network TerminationTE Terminal Equipment



LD 32

STAT l s c d Get status of specified Digital Subscriber Loop (0-7).

When getting the status of an unit where ACD sets are defined,the printout will not include MSB LOG OUT, MSB LOG IN, LOGIN, OR LOG OUT, according to the ACD set state.

If SUPP package 131 is not equipped, Tthe output format is:

DSL sw_state misp_state lc_state B1 statusB2 status

bri-18

If SUPP package 131 is equipped, the output format is:

DSL type: swstate L2_state L1_state dch_stateclk b1_state b2_state

Table 15 defines output fields. Table 16 on page 155 lists anddefines possible responses. when SUPP package 131 is notequipped. Table 17 on page 156 lists and defines possibleresponses when SUPP package 131 is equipped.

Table 15STAT l s c d Field Definitions

Field Definition

sw_state DSL software state

misp_state DSL state on the MISP card

lc_state DSL state on the BRI line card

swstate State of DSL/UNIT in software

L2_state Layer 2 state of DSL/UNIT in MISP loadware

L1_state Layer 1 state of line card

dch_state* State of D-channel link in software

clk* Clock mode

b1_state State of first B-channel

b2_state State of second B-channel

* these fields are output only for BRI trunks


Maintenance

LD 32

Table 16STAT l s c d Response Definitions: SUPP package 131 is not equipped

Response Definition

APDB MISP call application is disabled

BUSY Call is active

DOWN Link layer is not established

DSBL DSL is disabled

ESTA Link layer is established

IDLE No active calls

LCNR Line card is not responding

MBSY DSL is in maintenance busy mode

MPDB MISP is disabled

MPNR MISP not responding or message is lost

NTAN DSL is not assigned to a MISP

RLS Link layer is not established

UNDN DSL is in an undefined state

UNEQ Unequipped

UP Link layer is established

UTSM CPU is unable to send message to MISPor line card

XTDB Superloop is disabled

XPDB Controller is disabled



LD 32

Table 17: STAT l s c d Response Definitions when SUPP package 131 is equipped

Field Response Definition

type LINE BRI lineTRNK BRI trunk

swstate IDLE no active callBUSY active with a callUNEQ unequippedMBSY maintenance busy

L2_state UNEQ unequippedIDLE no active callBUSY active with a callMBSY maintenance busyDSBL disabledESTA D-channel link is establishedRLSU D-channel link is releasedTEST test modeRLBT remote loop backAPDB application disabledMPDB associated MISP disabledMPNR associated MISP not respondingUTSM unable to send message to MISP

L1_state UNEQ unequippedDOWN Layer 1 is downLCNR line card not respondingUP Layer 1 is up

UNDN undefined DSL stateXPDB associated XPEC is disabledUTSM unable to send message to MISP

dch_state

ESTA D-channel link is established

RLSU D-channel link is releasedTEST-IDLE test mode idleTEST-RLBT test mode remote loop back

(Part 1 of 2)


Maintenance

LD 32

clk DSBL disabledPREF primary referenceSREF secondary reference

b1_state UNEQ unequippedBUSY active with a callDSBL disabledMBSY maintenance busyIDLE no active call

b2_state UNEQ unequippedBUSY active with a callDSBL disabledMBSY maintenance busyIDLE no active call

Table 17: STAT l s c d Response Definitions when SUPP package 131 is equipped

Field Response Definition

(Part 2 of 2)



LD 32

STAT l s c u Get status of specified unit. Table 18 on page 158 definespossible responses to STAT lscu.

basic-1

Table 18STAT lscu Responses

Type Response Definition

Normal IDLE IdleIDLE REGISTERED

UNREGISTEREDi2004 that has registeredi2004 is configured in the system but not registered

MBSY Maintenance busyDSBL DisabledDSBL Virtual terminal disabled by ServerDSBL REGISTERED

UNREGISTEREDi2004 that has registered but is disabledi2004 is configured but not registered and in disabled state

BUSY In use by call processingBUSY BARRED Barring is applied to trunk with BARA Class of ServiceUNEQ Terminal not defined in softwareL500 Line is 500/2500 typeMBCS Maintenance setBCS Normal SL-1 telephoneTRK TrunkATTN Attendant consoleDTR Digitone ReceiverPWR Console power unit

Abnormal CARD x DSBL (OVD) Card x disabled due to overloadDND xxx xxx Do Not Disturb feature is activeSHELF DSBL(OVD) Shelf disabled due to overloadSIG FAULT Outgoing signal fault detected on PS card under examination.WARNING: CRPTRNOT IN RANGE

TN's data is corrupted. Check BUG messages relating to theTN.

Responses caused by invalid equipment choice:EXT DSBL Extender disabledLOOP NOT TERM Loop is not a terminal loopLOOP UNEQ Loop is unequippedSHELF UNEQ Shelf is unequippedSHELF UNEQ W/PBXCARDS

No 500 cards on shelf

CARD UNEQ Card is unequippedCARD NOT PBX Card is not a PBX cardUNIT UNEQ FOR MW Unequipped for Message WaitingPER UNEQ PS card is unequippedUNIT UNEQ Unit is unequipped


Maintenance

LD 32

STAT NCAL <c DSL#> qsig gf-22List all current call-independent connections on a given BRITDSL. (Option 11C)

The response format is as follows:

• NCALL CONN ID: a number in the range of 1-9999 thatidentifies the call independent connection on a givenDSL

• CREF: call reference number in HEX identifyingindependent connection

• STATE: current state of all call-independent connections(IDLE, CONN_REQ, CONN_EST)

• TIME: year month day hour:minute:second (the timewhen call independent connection request is made)

• APPL: applications using the call-independentconnection (e.g., NACD, NMS,...)

• ORIG: originator• DEST: destination

Note that the command format for an Option 11C is:

STAT NCAL <c 0 0 DSL#>

STAT NCAL <l s c DSL#> qsig gf-22List all current call-independent connections on a given BRITDSL.








To enter this command, QsigGF package 305 is required.



LD 32

STAT NCAL <l s c DSL#> <conn_ID> qsig gf-22List information pertaining to a specific call-independentconnection (as defined by its connection ID)








To enter this command, QsigGF package 305 is required.

STAT NWK l Check status of network card with specified loop, where loop isthe even or odd numbered loop on the network card.

basic-1

STAT PER x Get status of PS card x.

Where:

• x = 0-15, Option 81C with Fiber Network Fabric

If the PS card is disabled, the response is changed from DSBLto either:

1. DSBL: NOT RESPONDING = PS card x is either missing,faulty or disabled via the faceplate switch.

• If there is a fault in the extender pair for the networkshelf, the status of the PS card will also be:DSBL: NOT RESPONDING.

2. DSBL: RESPONDING = The PS card is disabled andresponding to the CPU. The PS may have been disabledby manual request (DSPS) or the associated extenderpair may have been manually disabled.

If neither of these conditions exists, the card may have beendisabled because of an overload condition on the associatedshelf. Check for OVD messages appearing in previous TTYoutput.

basic-1

fnf-25


Maintenance

LD 32

An attempt to enable a PS card which was disabled because ofan overload may result in a recurrence of the overloadcondition: the system's service may be impaired forapproximately 2 minutes.

STAT sl Get current status of superloop and separate carriers on thatsuperloop, based on data previously sent by the CarrierInterface F/W (LCIM).

For each carrier, the following fields will be displayed:

S/W State, SPARE Status, NND Status, TSA (TimeSlot Availability) and CALS.

TTSA = Number of Traffic Timeslots currently available for voiceand data calls out of a possible: 21 for T-1 and 27 for T-E.

SPARE Status indicates whether the carrier is spared andwhich carrier it is spared in.

NND Status indicates whether new data calls are disallowedon the timeslots being transmitted by the carrier.

rem_ipe-21

STIF L PDL2 l s c bri-19Displays link status for SAPI 16 interface of BRSC l s c for MPHon loop L.

STIF L PDL2 L1 bri-19Displays the link status for SAPI 16 interface of BRIL L1 forMPH on loop L.

STIF l PDNI y Displays the link status for interface Y for PDNI.Where: Loop Y = 1-3

bri-19

STIF l s c DSL DCH x bri-19Displays the link status for B-channel X for the DSL l s c D.Where: BCH stands for B-channel and X = 1–2.

SUPL (l) Print data for all or specified superloop(s). xpe-15Where:


fnf-25



LD 32

TRK l s c uc u

Seize specified trunk for outpulsing.Option 11C format

Command is valid at a maintenance telephone only. Thespecified trunk is connected to the maintenance telephone anda test call may be performed on the trunk. When the test call iscompleted, access sequence SPRE 91 must be redialed to usethe maintenance telephone to input more commands.

basic-1

XNTT l Do self-test of Network card for specified superloop. TheNetwork card must be disabled before the self-test.

xpe-15

Where:


fnf-25

XPCT x Do self-test on Controller x. The NT8D01 Controller must bedisabled before the self-test.

xpe-15

XPEC (x) Print data for all or specified Controller(s). xpe-15

Page 394 of 500 Option 11C commands


LD 80

Option 11C commandsOn an Option 11C system, some loop-level commands are replaced withslot-level commands. Valid commands for these systems are shown here:

TRAC c acod List route number, type and status of each trunk under customer cTRAC c dn Trace calls for customer c Directory Number or Local Steering Code dnTRAC c r m Trace calls for customer c, route r, member mTRAD c ch Trace digital calls, channel ch of card cTRAD loop ch Trace DTI calls, channel ch of loopTRAK c u Trace calls associated with this unitTRAK c u k Trace calls associated with key k on the specified unitTRAO c u Trace attendant calls, this unitTRAO c u k Trace attendant calls on key k of unitTRAO xx...xx DEV Print auxiliary dataTRAT c a Trace calls for attendant a of customer cTRAT c a k Trace calls associated with key k of attendant console a for customer c


Maintenance

LD 80

Alphabetical list of commands

Command Description Pack/Rel

DALL Disable all enhanced trace commands.

This command disables all trace commands enabled withENTC or ENTD command. You must stop the trace with theSTPT command before disabling all the commands with DALL.

basic-19

DIST n Disable the enhanced trace operation.

This command disables the trace command enabled withENTC or ENTD command. This command is used once a tracecommand is started then stopped.

Where: n = the entry number (as seen with the FITR command)

basic-19

ENTC l s c u t Enable the enhanced trace command for a TN.

This command enables the trace capability for the TN specified.Note that this command does not start the trace immediately.Use the GOTR command to begin the trace operation.

Where: l = loop, s = shelf, c = card, u = unit and t = the length oftime the trace command operates.

The format for the trace command duration (t) is HHMM, whereHH = hours (0-23)and MM = minutes (0-59). For example, for aduration of 5 minutes, t = 0005; for 1 hour, t = 0100

The time duration must be at least 1 minute, and no more than23 hours.

basic-19

ENTD l ch t Enable the enhanced trace command for a digital trunk.

This command enables the trace capability for the TN specified.Note that this command does not start the trace immediately.Use the GOTR command to begin the trace operation.

Where: l = loop, s = shelf, c = card, u = unit and t = the length oftime the trace command operates.

The format for the trace command duration (t) is HHMM, whereHH = hours (0-23)and MM = minutes (0-59). For example, for aduration of 5 minutes, t = 0005; for 1 hour, t = 0100. The timeduration must be at least 1 minute, and no more than 23 hours.

basic-19



LD 80

FITR Get information about the enhanced trace function. Thiscommand queries the TNs or Digital trunks being traced withthe ENTC and ENTD commands.

The output is shown as follows:

ENTRY TN or TRUNK TIME STATUS

For example:

1 01 0 01 01 0030 OFF2 015 04 1200 OFF

basic-19

GOTR Begin enhanced trace commands. This command starts thetrace operation specified with the ENTC and ENTD commands.

basic-19

STPT Stop the enhanced trace command.

This command stops the enhanced trace operation specifiedwith the ENTC and ENTD commands. This can be used at anytime during the trace operation. This does not disable thecommands; they can be restarted with the GOTR command.When they are restarted, the duration timer is reset.

For example: the timer is set at 30 minutes, but the trace isstopped after 2 minutes. When the trace is restarted (GOTR)the timer is set to 30 minutes.

basic-19

TRAC c acod List route number, type and status of each trunk for customer c. basic-1

TRAC c dn Trace calls for customer c Directory Number or Local SteeringCode dn.

basic-1

TRAC c dn Trace calls, this dn of customer c. basic-1

TRAC c r m Trace calls, customer c, route r, member m. basic-1

TRAC l s c DSLx bri-18Trace calls on Digital Subscriber Loop x (0-7).

TRAC l s c u Trace calls associated with this unit. If a trace is performed on aDTR, an error message is output.

basic-1

TRAC l s c u k Trace call associated with key k on specified unit. basic-1

TRAC x yyyy Trace using customer number as DN.

Where : x = customer number of the set to be traced andyyyy = DN of the key to be traced.

nxcc-22


Maintenance

LD 80

TRAC xx...xx DEV nxcc-22Print the auxiliary data related to the call for Network AlternateRoute Selection (NARS), Basic Alternate Route Selection(BARS), Coordinated Dialing Plan (CDP) or Ring Again (RGA),where equipped, as well as the normal data for commandxx...xx. Command xx...xx can be any of the TRAC commands.

When TYP E is output, E = extended route (not expensive).

TRAC zzzz Trace using TN of the set to be traced.

Where : zzzz = TN of the set to be traced.

nxcc-22

TRAD loop ch Trace DTI or DLI calls, channel ch of specified loop. basic-1

TRAD c ch Trace digital calls, channel ch of card c. (Option 11C)

TRAK c u Trace calls associated with this unit. (Option 11C) basic-1

TRAK c u k Trace calls associated with key k on the specified unit. (Option11C)

basic-1

TRAO c u Trace attendant calls, this unit. (Option 11C) basic-1

TRAO c u k Trace attendant calls on key k of unit. (Option 11C) basic-1

TRAO xx...xx DEV basic-1Print auxiliary data. (Option 11C)

TRAT c a Trace calls for customer c, attendant a. basic-1

TRAT c a k Trace calls associated with key k of attendant console a forcustomer c.

basic-1

TRAT l s c u Trace attendant calls, this unit. basic-1

TRAT l s c u k Trace attendant calls on key k. basic-1



LD 80

TRAT xx...xx DEV Print auxiliary data.

Print the auxiliary data related to the call for Network AlternateRoute Selection (NARS), Basic Alternate Route Selection(BARS), Coordinated Dialing Plan (CDP) or Ring Again (RGA),where equipped, as well as the normal data for commandxx...xx. Command xx...xx can be one of the TRAT commands.

basic-1



LD 95



AAA aaa Attendant Alternative Answering display mnemonicDefault = A

cpnd-10

ARE YOU SURE? cpnd-1(YES) NO (Confirm) or remove operation. The default response

is YES.

CFNA xxxx Call Forward No Answer display mnemonic cpnd-10Default = N

CFWD xxxx Call Forward All Calls display mnemonic cpnd-10Default = F

CNFG Configuration cpnd-10(ALON) Standalone CPND configurationREMO Interwork with a remote directory systemLOCL Interwork with a local (inboard) system

CPND_LANG CPND language. Prompted when FTR = CPND. cpnd-19(ROM) Roman CPND languageKAT Katakana CPND language

CUST xx Customer number associated with this function asdefined in LD 15

cpnd-10

DCNO 0-254 Digit Conversion table Number dnis-17

DES (NO) YES Designator for Multiple Appearance DNs allowed odas-10Prompted when ODAS is equipped.

DFLN 5-(13)-27 Default character string Length cpnd-10Default to 13 or MXLN, whichever is less. Promptedwhen STAL = YES

DIG 0-2045 0-99 Existing Dial Intercom Group number followed bymember number

di-10

<cr> To prompt DN

If CPND Name already exists, an error message isreturned. Prompted when DIG is equipped.


Administration

LD 95

DIG gg mm Existing Dial Intercom Group number followed bymember number (optional), where:

di-10

• gg = 0-2045

• mm = 0-99

gg Existing DIG Group numberWithout member number specified, ALL memberswithin this Group are printed.

ALL Print all Dial Intercom Groups.

<cr> Prompts DN

DISPLAY_FMT Display format for CPND name cpnd-19(LAST) Last name, First name (Doe, John)FIRST First name, Last name (John Doe)

DN xxxx Directory Number (Existing eligible DN or Partial DN).The DN can be up to 4 digits, up to 7 digits withDirectory Number Expansion (DNXP) package 150.

Valid DN types are Single or Multiple line prime DN,trunk DN, attendant DN or ACD DN. If Partial DN, allpossible DNs are printed.

cpnd-10

x...x y...y Range of DN-defined names are deleted/printed.This entry is valid when REQ = OUT/PRT.

ALL All names defined are deleted/printed. ALL is a validentry when REQ = OUT/PRT.

x/xx/xxx DNs starting with x, xx, or xxx are printed. This entryis valid when REQ = PRT.

<cr> To re-prompt DCNO

If the CPND name is already defined, an errormessage is returned.

HUNT xxxx Call Forward No Answer display mnemonic cpnd-10Default = B

IDC 0-254 Incoming DID Digit Conversion number dnis-17Existing complete or partial IDC number

ALL All Names defined




LD 95

LANG Language choice for name for CPND screen andset display. Allowed only if REQ = OUT.

cpnd-16

(ROM) English display (Roman characters)KAT Non-English display (Katakana characters)ALL Remove ALL names from CPND data block for the

DN or DIG selected.<cr> Roman (English) display

MXLN 5-(17)-27 Maximum allowable CPND character string Length cpnd-10Once an MXLN is entered, it cannot be changed toa lower value via the CHG prompt.

NAME a...a CPND Name using ASCII characters cpnd-19If STAL = YES, then Name size < XPLNIf STAL = NO, then Name size = number ofcharacters entered. DIG is reprompted.

<cr> to DN prompt

NITC (NI) aaaa Non intercom callNITC indicates that an intercom call terminated asa normal call.

PAGE (NO) Page headers and numbers not printed if the MultipleDN/DIG is specified.

cpnd-10

YES Page headers and numbers printed if the MultipleDN/DIG is specified.Page headers (date and page number) are notprinted if a single DN/DIG is specified.

PKUP xxxx Call Pickup display mnemonic. Default = P. cpnd-10

REQ Request. cpnd-10CHG Change existing data blockEND Exit Overlay programNEW Create CPND data blocks and/or name stringsOUT Remove existing name or data blockPRT Print an existing Name or data block from the data

base

RESN (NO) YES Display of Reason for redirecting calls allowed cpnd-19



Administration

LD 95

SHRT (NO) Prints one DN or IDC per single line. (long form) cpnd-10YES Prints several DNs or IDCs on a single line. (one-line

form)Prompted when DN = ALL, Range or Partial DN to bespecified.

STAL (NO) YES Static Allocation of Name storage

In a Hotel/Motel environment with BackgroundTerminal facilities, STAL must be YES.

STAL = YES is recommended whenever CPNDNames change frequently, for efficient use ofavailable memory (i.e., when a guest checks in).

cpnd-10

TYPE Type of data block cpnd-10CPND CPND data blockNAME CPND Name data block

Allowed only if CPND data block is already defined.

XFER xxxx Call Transfer display mnemonic

Mnemonic for call transfer display in Network CallRedirection (NCRD). One to four characters areaccepted.

Default = T. Prompted if ISDN = YES in LD 15

ncrd-16

XPLN xx Expected Length

Range must be between the Input Name length andthe MXLN, or it default to DFLN. This value should beset to a sufficient length to allow for current and futurenames to be entered.

When REQ = NEW, the XPLN prompt defines themaximum name length for that particular entry. TheXPLN for a DN cannot be changed without deletingthat name entry.

cpnd-10

<cr> This sets the XPLN to the input length, or DFLNwhichever is greater. Re-prompts DIG.

Prompted when STAL = YES


Administration


Documents

Learn Loads