LD Cooling LD PC-V10 USA and LD PC-V10 Reverse USA Phase ... PC-V10 User Manual U… · LD Cooling LD PC-V10, PC-V10 Reverse Phase Change include: LD PC-V10 Phase Change with universal

WEB: http://www.ldcooling.com/ Page 1

Email: [email protected]

LD Cooling LD PC-V10 USA and LD PC-V10 Reverse USA Phase

Change

Installation manual

Date: Version: Comments:

1.1.2012 1.1



LD Cooling LD PC-V10, PC-V10 Reverse Phase Change include:

LD PC-V10 Phase Change with universal mounting kit for all sockets

Backplate for all sockets

Backplate insulation

150cm of Armaflex Insulation Tape with self adhesive backing

25cm of insulation tube

4 x Screws

4 x Nuts

8 x Stainless steel washers

4 x Plastic washers

4 x Springs

4 x Thumb Screws

Installation manual



Motherboard preparation:

We recomend to use really popular material for sub-zero aplication these days called »art eraser«,

»rubber eraser« or »kneaded eraser«. This material is not included, but you can purchase it

through our website or other shops.

1. Use art aeaser on the backside of the motherboard.



2. Than use backplate insulation which is included with mounting kit, put universal backplate

on it and install 4 x M4 screws through original motherboard backplate.

Socket 2011. Installed M4 screws through original motherboard backplate.



3. We recomend to remove CPU hold down assembly and use »art eraser« like you can see on

the pictures.

Add thin layer of »art eraser« around the socket.

You can protect condensor, memory slots on motherboard with tape.



4. Install CPU hold down assembly back and continue adding »art eraser« around.





5. Add one layer of »Kitchen/Bathroom Towel« on »art eraser«.

6. On the end use one layer of Armaflex Insulation Tape with self adhesive backing.



Mounting installation:

Once motherboard insulation is done, install it into the case and than you only need to do a few

more things and you are done.

1. Cut insulation tube which is included and install it like you can see on the picture.

2. Now you only need to use some thermal paste (Artic Ceramique is recomended for sub-

zero temps) and install universal mounting kit on motherboard. Use washers, springs,

Thumb Screws and tighten them.



Installing LD PC-V10, PC-V10 Reverse:

1. Connect 2 PIN cable from controler (PWRSW) to Motherboard (POWER SW) where you

normaly connect power button from computer case.

2. With second 2 PIN cable connect 12V line from controler (CHK 12V) to Power Supply - PSU

12V line (Yellow cable and Black cable) or even better on motherboard 3pin fan connector.

3. Now when everything is done, press power button in the front of the case and you will see,

that controler/LCD will start counting down from 4 min to 0 min. Once it arrive to 0 min,

phase change will start working. When evaporator temperature reach -25c, controler

automaticly start PC and also start checking for 12V line. If everyting is connected right,

controler will recognize 12V line (if not turn 2 PIN cable for 180 to change + and -) from PSU

and PC will operate normaly. If your 12V line is not connected, phase change controler will

shut down phase change in 12 secoonds.

If you have any other question you can send us email on: [email protected] or contact shop

where you bought it.

mailto:[email protected]



Maintenance:

If you want that Phase Change unit operate at maximum performance, we recomend to clean

condensor in the front of the unit every month. The best way to clean condensor is with vacuum

cleaner or compressed air.

Phase Change needs good airflow through condensor for best performance.

Warranty:

Warranty of LD PC-V10, LD PC-V10 Reverse is 12 months from the date of purchase. Warranty Void

if you remove heat-shrink from schrader valve and also if you bend suction line to break it!

Documents

LD Cooling LD PC-V10 USA and LD PC-V10 Reverse USA Phase ... PC-V10 User Manual U… · LD Cooling LD PC-V10, PC-V10 Reverse Phase Change include: LD PC-V10 Phase Change with universal