Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
PSLFK3-24
V1.0LARGE FULL-MOTION TV WALL MOUNT
Thank you for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if
Engl ish - - - - - - - - - - - - - - - - - - - - - - - - 1 -10Deutsch - - - - - - - - - - - - - - - - - - - - - - - - 11-20França is - - - - - - - - - - - - - - - - - - - - - - - - 21-30Españo l - - - - - - - - - - - - - - - - - - - - - - - - 31-40I ta l iano - - - - - - - - - - - - - - - - - - - - - - - - 41-50
Tools Needed
Hammer
P1
Getting Started
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the weight of the TV (with accessories) does not exceed 60 kg.
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.If you do not understand the instructions or have any concerns or questions, please contact a qualified installer. Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you require replacement parts, contact customer service at
This product has been designed for use on a vertical wall constructed of wood studs. Wood studs being defined as a wall consisting of a minimum of 2” x 4” studs with a maximum of 16” stud spacing with a maximum of 1/2” of wall covering (drywall, lath, plaster).For custom installations please contact a qualified installer. For safe installation, the wall you are mounting to must support 4 times the weight of the total load. If not, the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure/surface will safely support the total load. This product may contain moving parts. Use with caution.DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.Please check www.perlesmith.com for more products and company information.
Stud Finder
Tape measure
1/2 in. (12.7 mm)
7/32 in.(5.5 mm)
Wood Drill
Screw driver
Pencil Level(included inside the box)
Drill 3/8 in.(10 mm)
Concrete Drill
CAUTION!
! 60 kg
MAXIMUM WEIGHT CAPACITY
P2
Arm andWall Plate
TV BracketsArm Extensions
Hardware Included
01 x1
03 x2
Front Support
End Caps
02 x1
05 x1
04 x2
Hardware (Wall /Product)
5/16 x 2½ inLag Bolts
x4
WallAnchor
x4 DA
WashersØ8mm
Allen Wrench
x4B
This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!
NOTE: Not all parts and hardware included will be used.
WARNING:
Philips ScrewsM6 x 15mmM6 x 30mm
Philips ScrewsM6 x 50mm
WashersØ6mmM4-5-6
Spacers
L10mm
x4x4
Philips Screws M8 x 15mmM8 x 45mm
x4x4 x8 x4M-DM-A M-B
x4M-C M-E
Philips Screws M8 x 65mm
x4M-F M-G M-H
Spacers L5mm
x8M-I
TV Screws / Washers
x1 C
Hardware
M8Nuts
x8E
WashersØ8mm
x8F
(product)
Wall Extension A
6A x2
Wall Extension B
6B x2
STEP 1-1 Select TV Screw Diameter
STEP 1-2 Select TV Screw Length
P3
Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fits your TV.
Correct CorrectToo LongToo Short
Measurement
200mm~600mm(7.9”~23.6”)
100m
m~4
00m
m(
3.9”
~15.
7”)
?
?
M6 M8
P4
STEP 1-3 Attach the TV Bracket
(a) Flat Back
04
Position your TV brackets over your TV hole pattern - making sure the brackets are centered and level over the TV hole pattern. Secure the brackets using your screw/washer/spacer selection:(a) for Flat Back(b) for Round Back / Extra space
CAUTION: Ensure TV bracket is securely fastened before moving on to the next step.
04
(b) Round Back / Extra Space
M-A M-D
M-H
M-B M-CM-EM-F
M-H
M-G M-I
STEP 2A Wall Plate Installation (Wood stud)
P5
2A-1 Attach the Extensions to the wall plate
the wall plate extensions can be moved 0.6”(15mm) for both side if necessary.
only one side need to attach each of extensions A and B
For 18”(457mm) to 24”(610mm) space studsFor studs with the sapce between 16.5“(420mm) to 18”(457mm)
6A
6B
0.6 Zoll
0.6 Zoll0.6 Zoll
0.6 Zoll
6B
6B
6A 6A
01
F E
CAUTION:
CAUTION: Avoid potential personal injury or property damage! All lag bolts A
MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 .
CAUTION: Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Drywall covering the wall must not exceed 5/8 in. (16 mm) Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
2A-2 Locate your studs. Verify and mark the center of the studs by finding the stud edges using an awl, a thin nail, or an edge-to-edge stud finder.
16”~24”(406mm ~ 610mm)
P6
2A-3Drill 4 pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. Make sure the depth is not less than 2 3/4” (70mm).
7/32
in.
Ø5.
5 m
m
in. (70 mm)
Configure A For 24”(610mm) space studs
Configure B For 18” (457mm) space studs
Configure C For 16.5” (420mm) to 18”(457mm) space studs
Mount wall plate using 4 sets of 5/16 lag bolts (a) and washers B with a 1/2 in. socket wrench (not included).
A B2A-4
2A-2Use wall plate to mark mounting location x4 locations for 24”(420mm)space studs.
Mark the 4 inside holes for 18”(457mm)space studs
Holes pattern for 16.5”(420mm) to 18” (457mm) space studs. Only one sied need to install the Wall Extension
OPT A OPT B OPT C
0101
leftright
010101
0101
leftright
010101
2
BA
STEP 2B Wall Plate Installation (Concrete or brick, No need wall extensions 06A and 06B )
CAUTION: Avoid potential personal injury or property damage! All lag bolts A
MUST BE firmly tightened to prevent unwanted movement of the wall plate 01 .
CAUTION: Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Drill pilot holes
2B-2
2B-3
01
AB D
Concrete Wall
Concrete Wall
D
01 ADB
01
Install wall plate using lag bolts and washer and anchor . Tighten the lag bolts until they are pulled firmly against the wall plate .
A
P7
2.75in 70 mm
Ø 1
0 m
m
Ø 10 mm
2B-1
01Position the wall plate at your desired height , level the wall plate and mark the pilot hole locations.
01
UP
STEP 3 Install Front support and extensions and End cap together.
Install the extensions [03] to Front support [02] with the pre-assembled screws.
Install the extensions [03] to Front support [02] withe the pre-assembled screws.
P8
B
3-1
3-2
Pre-assembled scews
Pre-assembled scews
Finished
02
03
05
P9
3-3
STEP 4 Hang TV with brackets [04] onto the arm extensions [02] and [03].
S1Hang 02 onto 01 and using a screwdriver, secure with preassembled screws
S1
S1
S2S2
01
02
04
03 02
Remove the preassembled screws [S2] and save to use, then raise the safety locks.
Press the safety locks then fasten the removed screws [S2].
Adjustments
P10
[S1]
TO ADJUST TV LEVEL, loosen the two screws [S1] on the rear of the arm plate, adjust level, and retighten to secure.
To adjust the tilt in both sides, loosen both tilt nuts and move panel to desired position. Tighten both tilt nuts to hold desired tilt.
!TIGHTEN
C
!LOOSEN
C
TIGHTEN
± 3°