Lanternnet.com Catalog

W.T. KIRKMAN IS A REGISTERED TRADEMARK WITH THE U.S. PATENT OFFICE, WASHINGTON, D.C.

Kerosene lanterns embody one of three distinct types of con-struction: Hot-Blast; Cold-Blast; or Dead-Flame. The Cold-Blast and Hot-Blast types are called Tubular Lanterns. In them, the kerosene vapor, mixed with air in proper ratio, com-poses the burning mixture. The burner acts as a carburetor to which the side tubes convey properly controlled air in regu-lated volume. The result is perfect combustion and bright, clean light. Both types operate with a balanced draft which, when tipped over, will self extinguish. The Hot Blast principle was patented in 1868 by John Henry Irwin, and was the first major advancement over Dead-Flame lanterns. Hot-Blast lanterns permit a portion of the spent air to re-circulate through the tubes, creating a brighter, more stable flame by using the downdraft to fan the flame. Cold-Blast lanterns first became popular in the 1890s, and are easily the most efficient of all. They are constructed so that only fresh, cold air enters the tubes, while all of the spent air is diverted and expelled. (Cold-Blast lanterns provide about twice the brightness of Hot-Blast lanterns.) Dead-Flame lanterns date back hundreds of years, and were originally just a simple enclosure for candles. They operate by taking in fresh air through holes or baffles at the bottom, and then expel spent air out the top. Tubular lanterns produce a steadier flame and much more light than Dead-Flame lanterns.

Approved Fuels for Tubular Lanterns 1. Non-Dyed* (Clear) K1 Kerosene (Outside use only) 2. Synthetic Kerosene (*Clear-Lite) 3. Klean-Heat Kerosene Substitute 4. Standard Clear Lamp Oil (Aladdin, Crown, or Medallion) 5. Citronella Oil (Outdoor use only, mix with kerosene 50:50) 6. W.T. Kirkman Whale Brand Bio-Fuel Lamp Oil *Dyed kerosene or lamp oil will eventually clog the wick and inhibit proper operation. It can also permanently stain the lamp or lantern. Paraffin Oil is NOT designed or suitable for use in tubular lanterns or oil lamps with 5/8 or larger wick. Paraffin oil has a much higher viscosity, and a flash point of 200 degrees or higher, as compared to the flash point of 150 degrees for kero-sene. These differences inhibit the capillary action of the wick, and will cause Lamps and Lanterns with 7/8" or lar-ger wick to burn improperly and erratic.

WARNING: NEVER USE gasoline, Coleman fuel, white gas, paint thinner, (aka mineral spirits,) wood alcohol, naptha, turpentine, benzene, or any other explosive fuel in a

wick lamp or lantern of any type. USING ANY OF THE ABOVE FUELS IN A WICK LAMP

OR LANTERN CAN RESULT IN PROPERTY LOSS, SERIOUS INJURY, OR DEATH.

TROUBLE FREE OPERATION TIPS

Every Time A Lantern Comes Off a Job: 1. Inspect the globe for cracks or chips. 2. Clean the lantern, check for damage. 3. Clean the burner for even burning. Periodically soak the burner in white vinegar if necessary. 4. Brush char off wick and clean charcoal out of holes in burner around wick holder 5. If lantern is out and there is still fuel in it - check wick length, replace if needed. 6. Always use 125 to 150 degree kerosene, or regular lamp oil (Not Paraffin,) for best results. 7. Never use gasoline, paint thinner, mineral spirits, Coleman fuel, or any other explosive oil with a wick. 8. Avoid using colored or tinted oils as they will gum the wick and inhibit the capillary action. 7. Paraffin oil should not be used with 7/8" or larger wick due to the difference in viscosity. (Paraffin burns with a 50% reduction in light output.)

N_w For 2013! W.T. Kirkman is proud to introduce the biggest advance-ment in lamp and lantern fuel in more than 50 years, WHALE BRAND Bio Fuel Lamp and Lantern Oil, the safe and smokeless alternative to petroleum and paraffin based oils. This entirely new environment friendly fuel has been in development for the past five years, the production proc-ess of which has been submitted to the U.S. Patent Office. The Patent Pending Process recycles vegetable oils used initially in the production of household soap products, and results in what may be the most perfect non-aromatic lamp and lantern oil ever produced. This vegetable based fuel has a flash point of 183 degrees, yet burns equal in bright-ness to kerosene or standard lamp oil, and is safe for long term storage. Perfect for use in all tubular lamps and lan-terns, flat wick, Kosmos, and mantle oil lamps. SPECIFICATIONS Convenient Two Liter Containers Packed Six per Case 100% Recycled Vegetable Hydrocarbons 183 Degree Flashpoint Contains no Sulfur or Toxins Satisfaction Guaranteed Patent Pending Imported from Germany, Packaged in U.S.A.

The New W.T. Kirkman No. 92 Ramona Polished Solid Brass Table Lamp is a stunning addition to our catalog, and is available with Kosmos, Matador, Duplex, and Aladdin burner options. Temporary Aladdin electric converters or permanent electric conversions also available. SPECIFICATIONS 24 oz. Fount Approximate 24 Height Lamp Made in U.S.A. Vianne Shades Shown Made in France Burners Made in France or China Satisfaction Guaranteed No. 92-14 w/#14 Kosmos Burner & Chimney $129.95 No. 92-14-GSA with Cranberry Gas Shade $189.95 No. 92-20 w/#20 Matador Burner & Chimney $145.95 No. 92-23 w/#23 Aladdin Burner $199.95 No. 92-23-GSA with Cranberry Gas Shade $269.95 No. 92-23-SS with Cranberry Student Shade $279.95 No. 92-25 w/Duplex Burner & Chimney $128.95 No. 92-25-GSA with Cranberry Gas Shade $188.95

1.

No. 1 Little Champ Cold Blast Lantern

The W.T. Kirkman No. 1 Little Champ is the 3/4 version of the No. 2 Champion, and the smallest tubular lantern in our Pre-mium Grade Signature Series, and now features a full weight pressed globe bearing our trademark, and features our improved #201 Wing-Lock Burner with brass wick tube for unparalleled operation. The durable Bright Galvanized finish is reminiscent of the lanterns produced in the late 1800's into the 1930's, and is especially appropriate for applications that demand both historic accuracy as well as durability and performance. SPECIFICATIONS 12" Height (Bail Up Height 16 1/4") 5/8" Wick Average 9 Candle Power 9 oz. Fount Capacity 12 Hour Burning Time Approx. Thermal Output: 1100 BTU/Hour Full Weight Pressed WTK #857 Globe Optional Solid Color Amber, Blue, Green or Red Globes Packed One Dozen per Case (Also Sold Individually) Includes Handy Funnel for oiling Wicked and ready to add oil Black or Bright Galvanized Finish Clear or Colored Globe Imported

Party Lantern Sets Five festive W.T. Kirkman Premium Grade Lanterns, perfect for use around the patio or BBQ. Your Choice of the No. 1 Little Champ, No. 2 Champion, or No. 350 Little Giant lanterns with assorted globes: Amber, Blue, Green, Red, and Clear.

No. 350 Little Giant Cold Blast Lantern

The W.T. Kirkman No. 350 Little Giant Lantern is our homage to the Dietz model of the same name first introduced in 1926, and the Embury #350 Little Supreme & Little Air Pilot lanterns, all of which used the Little Wizard size globes. The #350 Little Giant features an original style globe guard, our exclusive WTK #201 Wing-Lock Burner, and a full weight pressed "Loc-Nob" globe bearing our trademark. The durable Bright Galvanized Steel version is highly rust resistant and reminiscent of the lan-terns produced in the late 1800's into the 1940's. SPECIFICATIONS 12" Height (Bail Up Height 16 1/4") 5/8" Wick Average 9 Candle Power 31 oz. Fount Capacity 40 Hour Burning Time Approx. Thermal Output: 1100 BTU/Hour Full Weight Pressed WTK #851 Globe Optional Solid Color Amber, Blue, Green or Red Globes Packed One Dozen per Case (Also Sold Individually) Includes Handy Funnel for oiling Wicked and ready to add oil Black, Red, or Bright Galvanized Finish Clear or Color Globe Imported

No. 1 Little Champ Party Lanterns

2.

W.T. Kirkman No. 2 Champion Cold Blast Lanterns

Our Most Popular Lantern Model!

The W.T. Kirkman No. 2 Champion is the largest lantern in our Premium Grade Series, and the most popular. This versatile and rugged model has exclusive features, including: An improved wing-lock burner with brass wick tube; Durable all galvanized construction; and a full-weight pressed "Loc-Nob" globe bearing our trademark. The No. 2-P Patio version features a removable 1 7/8 post adapter and domed reflector. The Bright Galvanized Steel finish is reminiscent of the lanterns produced in the late 1800's into the 1930's, and is especially appropriate for applica-tions that demand both historic accuracy as well as durability and performance.

If you plan to only own one tubular lantern, this is it!

SPECIFICATIONS 15" Height (Bail Up Height 20 1/2") 7/8" Wick, Average 12 -14 Candle Power 31 oz. Fount Capacity, 27 Hour Burning Time Approx. Thermal Output: 1400 BTU/Hour Full Weight Pressed WTK #852 Globe Clear Globe Standard Optional Solid Color Amber, Blue, Green or Red Globes One Dozen per Case (Also Sold Individually) Includes Handy Funnel for Oiling Wicked and Ready to Add Oil No. 2 Available in Black or Bright Galvanized Finish No. 2P Available in Bright Galvanized Finish Only Imported

Satisfaction Strictly Guaranteed!

No. 2 Champion Lantern Crate Our No. 2 Champion Lantern Crates are hand constructed here in our Southern California shop of pine and ash. Each crate features the W.T. Kirkman "Premium Grade" logo stamped into the end pieces. A great collectable and gift idea!! SPECIFICATIONS: 9" x 9" x 18" Scant Your Choice of Stain Color (Specify) Crate Proudly Made in the U.S.A. Satisfaction Strictly Guaranteed!

No. 2 Warming Plate To answer the requests for a food or beverage warmer for use with the larger lanterns, we have developed the No. 2 Warming Plate for dependable camping or emergency use. It simply snaps onto the lantern crown when needed, and does not inhibit the normal operation of the lantern. Fits our #2 Champion, the Dietz #80 Blizzard, #90 D-Lite, #2500 Jupiter, as well as most all Dietz #2 size lanterns made since 1898.

SPECIFICATIONS Durable Zinc Finish Sturdy 2 pound capacity 4" Diameter Flat Surface for Mug or Bowl Proudly Made in the U.S.A.

No. 2 Champion Lantern

No. 2P Patio - Post Lantern

3.

No. 2-PHR Champion Post

Reflector Lantern The No. 2 Champion Post Reflector Lantern is perfect for applications where electricity isn't available, or near pools or spas where it is prohibited. The 12" Hooded Reflector is pitched to redirect all the light normally cast upward so to eliminate all shadow under the lantern. Square or round post sizes available. SPECIFICATIONS No. 2 Champion Lantern (Imported) 12 Diameter Reflector (Made in U.S.A.) Wicked and ready to add oil Black or Bright Galvanized Finish Lantern Imported

No. 1 and No. 2 Hooded Reflector Lanterns

Our exclusive Hooded Reflector Lanterns are amongst our best selling items, and are designed for use directly over any area that needs extra light, such as a table or desk. They are pitched to focus the light normally cast upwards directly under the lantern with no shadow. Authentic to the original patterns from the late 1800s, each of our hooded reflectors are constructed by hand in our California shops, and are the per-fect compliment to outfit your chuck wagon, cabin, or off-grid home. (We also sell our hooded reflectors separately for most all lantern models in either brass or galva-nized steel construction.) SPECIFICATIONS NO. 1-HR No. 1 Little Champ Lantern (Imported) Overall Height 16 1/4" 10 Dia. Reflector (Made in U.S.A.) Wicked and ready to add oil Black or Bright Galvanized Finish Lantern Imported

NO. 2-HR No. 2 Champion Lantern (Imported) Overall Height 20 1/2" 12 Dia. Reflector (Made in U.S.A.) Wicked and ready to add oil Black or Bright Galvanized Finish Lantern Imported

WTK No. 411E & WTK No. 262E Electric Burner Adapters

Our electric adapters can be used with your #1 or #2 size lanterns (with wing-lock cone burners,) without drilling or modifying the lantern. Simply empty the tank and remove the kerosene burner and replace it with the electric burner. To use the lantern with oil, replace the original kerosene burner. The optional Hi-Lo switch can extend the bulb life infinitely when used in the low setting. SPECIFICATIONS 7' Polarized Cord Set with Line Switch 60 Watt Candelabra Base Flame-Tip 2500 Hour Bulb Included Assembled in U.S.A. W.T. Kirkman Exclusive

4.

W.T. Kirkman No. 0 Tubular Hot Blast

Reflector Lantern

Our solid brass No. O Tubular lantern with the addition of a corrugated wall reflector. Patterned after the wagon dash lanterns of years ago. SPECIFICATIONS 15 1/2" Height Average 5 Candle Power 5/8" Wick 14 oz. Fount Capacity 23 Hour Burning Time Made in U.S.A.

W.T. Kirkman No. 0 Tubular Fire Dept Hot Blast Lantern

The W.T. Kirkman No. 0 "FIRE DEPT" Lantern is a stunning showpiece, and can be used to crown restored 1890 to 1910 fire apparatus, or it is the ideal fireman retirement gift. Hand made in the U.S.A. of polished solid brass. Options include engraved globe, tank tag, nickel plating, bulls eye lens, colored globe, etc. SPECIFICATIONS 16" Height 6 Bottom Diameter Average 5 Candle Power 5/8" Wick 8 oz. Fount Capacity 12 Hour Burning Time Tank Embossed FIRE DEPT Made in U.S.A.

W.T. Kirkman No. 0 Tubular Solid Brass Hot Blast Lantern

The W.T. Kirkman No. 0 "Tubular" Brass Lantern is the first "tubular" hand lantern made in the U.S.A. in over 40 years. Our goal was to produce a lantern true to the earlier designs of the 1870's to '90's, but to also incorporate some of the later improvements, such as the leak-proof double crimp tank and wing-lock burner. The result of our efforts is the finest lantern made today. It is sure to become a collector's piece, as production is very limited and each one is numbered and registered to it's owner. SPECIFICATIONS 15 1/2" Height 5 3/4 Bottom Diameter Average 5 Candle Power 5/8" Wick 14 oz. Fount Capacity 23 Hour Burning Time Made in U.S.A.

5.

No. 1900 Lantern Bracket Adapter

Use to hang wire frame railroad lanterns on any of our marker lamp brackets or most American marker lamp brackets. Fits the Dietz No. 041, No. 100 Watch-man and No. 999 Kero, as well as the ob-solete Dietz Vesta, and #39 lanterns, etc..

W.T. Kirkman No. 100 Watchman

Signal Lantern

The exclusive W.T. Kirkman No.100 Watchman "Dead Flame" signal/safety lantern features all galvanized steel construction, an improved 3/8" burner, reinforced cage, and a drop out style oil tank. Available with custom markings on globe and reflector. SPECIFICATIONS 12" Height (16 Overall) 6 1/2" Diameter Base Average 3 Candle Power, 3/8" Wick 6 oz. Fount Capacity 10 Hour Burn Time Wicked and ready to add oil Imported

No. 33 Footless Lamp Bracket

2" x 3 3/8" Footprint Size BRACKET SPECIFICATIONS Cast Aluminum Construction Accepts Wedge 9/32" Thick x 1 5/16" Width (at top) Compatible with most all marker lamps made by Adams and Westlake, (Adlake) Armspear, Dressel, etc. Black Enamel Finish

W.T. Kirkman No. 999 Kero

Railroad Lantern We are proud to introduce our exclusive #999 Railroad Lantern in beautiful bright nickel plate finish. If this model looks familiar, that is because it is produced using some of the original tooling for the Adams and Westlake "Kero" model dating to the 1920's. The oil burning version features a solid brass oil pot and #391 Convex burner, and a full weight pressed globe bearing our trademark. The Deluxe Electric Table Lamp version features a vintage style brown cloth covered cord with line switch, and 60 Watt bulb. This lantern will make the perfect gift for any railroad buff. SPECIFICATIONS 9" Height (15 Overall) 6 1/2" Diameter Base Average 3 Candle Power 5/8" Wick 6 oz. Fount Capacity 10 Hour Burning Time Solid Brass Oil Pot and Burner Bright Nickel Plate Finish Made in the U.S.A. Wicked and ready to add oil, or electrified and ready to plug in.

6.

Height: 13" Width: 8" #2 Queen Anne Oil Burner Average 10 Candle Power 33 oz. Fount Capacity 28 Hour Burning Time Made in U.S.A. Burner Imported



Chimney Holder 2 1/2 Inside Diameter Made in U.S.A. Fount Holder 4 1/4 Inside Diameter Made in U.S.A.



Height: 15" Width: 5" Projection: 5" Antiqued Solid Brass 12 Volt or 120 Volt UL Listed or O.E.M. Made in U.S.A.


7.

12-16 Candle Power Output Casts No Shadow 20+ Hour Burn Time per Tank Regulated & Filled From the Outside Reflector Diameter: 15" Height: 26" Made in U.S.A.

18" High, 10 1/2" Wide, 8 1/2" Deep #2 Eagle Burner, 7/8" Wick Average 10 Candle Power 18 oz. Fount Capacity 15 Hour Burning Time #860 Pearl Top Chimney Made in U.S.A.

12-16 Candle Power Output Casts No Shadow 20+ Hour Burn Time per Tank Regulated & Filled From the Outside Reflector Diameter: 15" Height: 23" (Less bail) Made in U.S.A.

WTK No. 1880 Dietz Style Wall Bracket

18" Span, 10" Height 2 7/8 Tapered Cedar Plug or 3 Strait or Tapered Plug Rust Proof Cast Aluminum Enamel Finish Made in U.S.A.

WTK No. 1886 Ham Style Wall Bracket

14" Span, 8" Height 2 7/8 Tapered Cedar Plug or 3 Strait or Tapered Plug Rust Proof Cast Aluminum Enamel Finish Made in U.S.A.

WTK No. 300TANK Replacement Tank & Burner

#2 Burner, 7/8" Wick 12-20 Candle Power Output 20+ Hour Burn Time Replacement for Dietz #3 and Ham #9 Custom specifications available Made in U.S.A.

8.

SPECIFICATIONS FOR LAMPS ON THIS PAGE Solid Brass Construction Polished or Antiqued Finish Electric Conversions Also Available Made in India Satisfaction Guaranteed

Self leveling gimbaled design perfect for sail boats or yachts Solid Brass Construction Polished or Antiqued Finish Made in India Satisfaction Guaranteed

Weighted Base Integrated Reflector Solid Brass Construction Polished or Antiqued Finish Made in India Satisfaction Guaranteed

9.

Dietz No. 8 Air Pilot

13 1/2" Height Average 12 C.P. 7/8" Wick 31 oz. Capacity 27 Hour Burn Time Blue/PT, Black/PT Blue/BT, Black/BT Imported

Dietz No. 2000 Millennium Cooker

The Dietz #2000 Millennium Cooker Lantern was developed to heat water or food for emergency or camping use indoors or out. Its compact design is similar to the Dietz #30 Little Wizard lantern, and will burn for 23 hours per filling. Included is an aluminum plate and 12 oz. cup to heat water, soup or a small meal, as well as a snap-on bracket and hold-down pegs to prevent tip over when used outdoors. A must have for emergency preparedness kits.

12" Height, 6" Base Diameter Plate and cup: 4 1/2" OD Average 9 Candle Power, 5/8" Wick 17 oz. Fount Capacity, 23 Hour Burning Time Apprx. Thermal Output: 1100 BTU per Hour Green/NT Imported

Dietz No. 80 Blizzard

15" Height Average 12 Candle Power 7/8" Wick 31 oz. Fount Capacity 27 Hour Burning Time Blue/PT, Red/PT, Black/PT Black/BT Imported

Dietz No. 90 D-Lite

13 1/2" Height Average 12 Candle Power 7/8" Wick 31 oz. Fount Capacity 27 Hour Burning Time Blue/PT, Black/BT Imported

Dietz No. 2500 Jupiter

15" Height Average 12 Candle Power 7/8" Wick 84 oz. Fount Capacity 75 Hour Burning Time Blue/PT, Black/PT Imported

Dietz No. 20 Junior

12" Height Average 9 C.P. 5/8" Wick 9 oz. Capacity 12 Hour Burn Time Blue/PT, Black/PT Red/BT, Black/BT Imported

Dietz No. 10 Monarch

13 1/2" Height Average 5 C.P. 5/8" Wick 17 oz. Capacity 23 Hour Burn Time Blue/PT, Black/PT, Green/PT Black/BT Imported

10.

Dietz No. 30 Little Wizard

12" Height Average 9 C.P. 5/8" Wick 17 oz. Capacity 23 Hour Burn Time Tin Plated Imported

Dietz No. 1 Large Fount Little Wizard

12" Height Average 9 Candle Power 5/8" Wick 31 oz. Fount Capacity 45 Hour Burning Time Blue/PT, Red/BT Imported

Dietz No. 76 The Original

10 1/2" Height Average 5 Candle Power 1/2 Wick 8 oz. Fount Capacity 11 Hour Burning Time Blue, Green, Red/PT, Black/BT & Solid Brass Imported

Dietz No. 041 Watchman

12" Height Average 3 Candle Power 3/8" Wick 10 oz. Fount Capacity 6 Hour Burning Time Black/BT Imported

Dietz No. 20-LED Junior

12" Height Average 16 Candle Power Adjustable Brightness Switch Takes 4 AA Batteries Batteries Not Included 100,000 Hour Rated L.E.D.s Black or Red w/ Nickel Trim Imported

Dietz No. 086 Star Combination Oil/Candle Lanterns

8 1/4" Height, 4 3/4" Base Diameter Average 1 Candle Power 1/16 Wick Diameter 4 oz. Tank, 6 Hour Burn Time Includes Tea-Light Candle Holder Antique or Satin Black Imported

Dietz No. 30 Little Wizard

12" Height Average 9 C.P. 5/8" Wick 17 oz. Capacity 23 Hour Burn Time Blue w/ Plain Trim Black w/ Brass or Nickel Trim Imported

Dietz No. 50 Comet

8 1/2" Height Average 4 C.P. 3/8" Wick 7 oz. Capacity 12 Hour Burn Time Tin Plated Imported

11.

Feuerhand No. 276 Baby Special Cold Blast Lanterns We are proud to reintroduce the Feuerhand #276 "Super Baby" lantern to our catalog. Feuerhand has been making hurricane lanterns in Germany since 1902, and is in fact the last of the original tubular lantern manufacturer still producing lanterns in the western hemisphere. The #276 "Super Baby" lantern is known the world over for its excellent finish and high quality leak-proof construction. The burner is specifically engineered to operate with no flickering or soot from the flame. The #276 lan-terns feature heat resistant SUPRAX globes that can withstand operation in rain or snow without cracking. SPECIFICATIONS 10 1/4" Height, 5 1/4" Base Diameter Average 7 Candle Power, 1/2" Wick 10 oz. Fount Capacity, 20 Hour Burning Time Tin Plated, Black, Blue, Green, Red, and Yellow Made in Germany Wicked and ready to add oil Genuine Feuerhand Replacement Parts #261 Fuel Cap 7/8 Diameter $2.95 ea. #275 Rising Cone Burner $6.95 ea. #1276 Clear Suprax Globe $5.95 ea. Made in Germany Replacement Wick Highest Quality tight-weave Red Stripe Flat Wick #804 1/2 Flat Wick (Pair) $1.50 pr. #804-33 1/2 x 33 Flat Wick $19.95 ea.

12.

Base: 5" Dia. Height: 10" #1 Queen Anne Oil Burner 10 oz. Fount Capacity 12 Hour Burning Time Made in U.S.A. Burner Imported

Height: 12" Width: 8" #2 Queen Anne Oil Burner Average 10 Candle Power 12 oz. Fount Capacity 10 Hour Burning Time Made in U.S.A. Fount and Burner Imported

4 1/2" Diameter Base 11" Height 1 Candle Power Polished Solid Brass or Antiqued Solid Brass Authentic 1894 Design Made in U.S.A.

4 1/2" Diameter Base 12" Height Average 10 Candle Power 12 oz. Fount Capacity 10 Hour Burning Time Made in U.S.A. Fount and Burner Imported

4 3/8" Bottom Diameter 10 1/2" Overall Height 12 oz. Fount Capacity 15 Hour Burning Time Made in U.S.A. Burner Imported

4 3/4" Bottom Diameter 12" Overall Height 18 oz. Fount Capacity 15 Hour Burning Time Made in U.S.A. Burner Imported

5" Diameter Base 11 1/2" Overall Height 14 oz. Fount Capacity 16 Hour Burning Time Made in U.S.A. Burner Imported

4 1/2" Diameter Base 12" Height Average 10 Candle Power 12 oz. Fount Capacity 10 Hour Burning Time Made in U.S.A. Fount and Burner Imported

13.

SPECIFICATIONS #10580-100 Opal #10580-101 Clear #10580-102 Ruby #10580-103 Cobalt (Shown) #10580-105 Green #10580-106 Lt. Blue #10580-107 Amber #10580-108 Emerald

SPECIFICATIONS #73805-100 Opal #73805-101 Clear (Shown) #73805-102 Ruby #73805-103 Cobalt #73805-105 Green #73805-106 Lt. Blue #73805-107 Amber #73805-108 Emerald

SPECIFICATIONS #73813-100 Opal (Shown) #73813-101 Clear #73813 102 Ruby #73813-103 Cobalt #73813-105 Green #73813-106 Lt. Blue #73813-107 Amber #73813-108 Emerald

SPECIFICATIONS FOR LAMPS ON THIS PAGE 12" Overall Height 5 3/4" Extreme Diameter 3 3/4" Bottom Diameter 12 Oz. Fount Capacity 10 Hour Burning Time Wicked and ready to add oil

14.

1880s Styling, ideal for Hallways and Foyers with 9 or higher ceilings. SPECIFICATIONS 22" Overall Height 18" Diameter Reflector (Optional) Average 12 Candle Power 27 Hour Burning Time #162 Solid Brass Queen Anne Burner #830 3" x 8 1/2" Plain Top Chimney Electric Versions Also Available

1880s Styling, ideal for Store Rooms and Kitchens with 10 or higher ceilings. SPECIFICATIONS 30" Overall Height 22" Diameter Reflector Average 20 Candle Power 20 Hour Burning Time #163 Solid Brass Queen Anne Burner #868 3" x 14" Plain Top Chimney Electric Versions Also Available

Authentic 1870s pattern with operating counterweight. Good for over tables. SPECIFICATIONS 31" Overall Drop Height #8400 14" Dia. Opal Slant Shade Average 10 Candle Power 10 Hour Burning Time #162 Solid Brass Queen Anne Burner #836 3" x 10" Plain Top Chimney Electric Versions Also Available

SPECIFICATIONS FOR ABOVE LAMPS #162 Solid Brass "Queen Anne Burner #840 Lotus Chimney (Chimney Substitutions Per Request) Wicked and ready to add oil

15.

SPECIFICATIONS 12" Overall Height #162 "Eagle" Type Plated Burner Packed Four per Case (Also Sold Individually) Wicked and ready to add oil

SPECIFICATIONS 10" Overall Height Pixie Burner, 3/16 Round Wick Packed Six per Case (Also Sold Individually) Wicked and ready to add oil




SPECIFICATIONS 11 Overall Height 4 Base Diamter #2 Brass Plate Eagle Burner #333 Hooded Chimney Wicked and ready to add oil

The No. 67513 Lamp is now the largest of our glass fount oil lamps. Truly an impressive lamp with traditional styling at an affordable price. Popular for both decorator as well as emergency use. Available with brass plated or solid brass burners, and either plain or large pearl top Chimney. SPECIFICATIONS 18" or 19 1/2 Overall Height 48 oz./40 Hour Capacity Average 9 Candle Power #836 Plain 10 Chimney, or #865 Large Pearl Top Chimney (Shown) Packed 6 Per Case (Also Sold Individually) Imported Wicked and ready to add oil

16.

The W.T. Kirkman #2009 Emergency Oil Lamp Kit includes an 8 ounce Mason Jar Fount and Adapter Ring, #2 Eagle Type Brass Plated Burner and Wick, #840 Lotus Chim-ney, and a 32 ounce bottle of Medallion Lamp Oil. This lamp will burn 7 hours per filling, (28 hours per quart of lamp oil.) Each kit is individually boxed for easy storage or gift giving. The Mason jar fount compliments the country living or crafts motifs, and can be used as a decorator piece in addition to provid-ing emergency backup light.

SPECIFICATIONS 12 1/2" Overall Height #162 "Eagle" Type Plated Burner 32 oz. Oil Included Individually Boxed Kit Assembled in U.S.A. with American Made and Im-ported Components Wicked and ready to add oil PLEASE NOTE: The Complete Kit with oil only be shipped via UPS Ground Service.

W.T. Kirkman Exclusive! The flame effect you've unknowingly seen at amusement parks and in motion pictures is now available direct to the general public. The W. T. Kirkman #F110 FAUX-FLAME module uses microchip technology to simulate the look of a real flame using any standard light bulb. When used with frosted glass to hide the light bulb, only you will know that you aren't burning kerosene. Dual brightness and flicker controls allow you to obtain the exact flame look you desire. Perfect for use in electrified kerosene or candle lanterns. The optional By-Pass mode allows the user to bring the fixture to full brightness by simply interrupting the power for 1 second. After the lamp is turned off, it will resume the flicker effect the next time it is turned on. The W. T. Kirkman #F110 FAUXFLAME module is designed for professional in-stallation only, and should only be installed by those fa-miliar with electric circuitry and safety. See the FAUX-FLAME module in action at: www.Fauxflame.com Specifications: 110-120 Volts AC, 200 Watt Max. 12 Volts AC, 25 Watt Maximum 12 Volts DC, 25 Watt Maximum

SHOWN ACTUAL SIZE 2 3/8" x 1 3/8" x 13/16"

17.

ELECTRIC LANTERN CONVERSION LETTER CODE To Specify an Electric Lantern, add the desired suffix codes below to the lantern model number of your choice.

Choose no more than one code from each category, for example, a black enamel #20 Junior lantern top wire with a ceiling canopy, brass hooded reflector, and frosted globe would be listed as: #20-TC-HR-FG-BLACK/BRASS.

The same lantern in Oxidized Nickel finish would be a #20-TC-HR-FG-ON.

1

CODE Electric Conversion Types A Awning & Patio Lights (4 Lanterns Per Set)

B Bottom Wired (6' 18/3 Jacketed Cord) (Wire exits underside of tank)

BCM Bottom Wired with Concealed Mounting Ring (6' 18/3 Jacketed Cord) (Wire exits underside of tank)

GPR Gold Pan Wall Reflector (Fits #10 Monarch, #20 Junior, or #80 Blizzard Only)

H Hook & Wall Canopy (Antique Brass or Polished Brass, Custom Finishes Available)

J J-Hook & Wall Canopy (Antique Brass or Polished Brass, Custom Finishes Available)

L Table Lamp Conversion (7' 18/2 Cord, Polarized Plug, Line Switch & Bulb)

P Post Lamp (Conversions Fit Standard 3" Post, Unless Specified Otherwise)

S Side Wired Conversion (6' 18/3 Jacketed Cord, No Switch or Plug, Wire exits rear of tank )

SR Slide-On Reflector Conversion (Brass, Copper, or Galvanized Steel)

T Top Wired Conversion (6' 18/3 Jacketed Cord No Switch or Plug)

TCB Top Wired with Concealed Bail

TCBC Top Wired with Concealed Bail with Ceiling Canopy (Matching Canopy, No Switch or Plug)

TCBWH Top Wired with Concealed Bail and Wall Hook

TC Top Wired Conversion with Canopy (Matching Canopy, No Switch or Plug)

TEB Top Wired with Electrified Bail (12 Volt Only)

WF Wall Fixture Conversion for Kosmos Lamps

WR Wall Reflector Conversion (Antique Brass, Brass, Copper, or Galvanized Steel)

WW-Rim Wagon Wheel Chandelier Conversion (Rim Mount)

WW-Strap Wagon Wheel Chandelier Conversion (Strap Mount)

Z Customer Specified Conversion (Pricing on Application)

2 Optional Down light Can for T, TC, or WR Conversions

D Down Light Can (Adds 4" to Tank)

D-FD Down Light Can (Adds 4" to Tank) with Frosted Diffuser Lens

3 Optional Hooded Reflector for B, BC, L, P, T, TC, or WW Conversions HR Hooded Reflector (Antique Brass, Brass, Copper, Rust, or Galvanized Steel)

4 Optional Swag Chain for TC Conversions SWAG Swag Chain by the Foot (Specify Length and Finish)

5

Optional Finishes AGED Aged Galvanized Finish (Galvanized Lanterns & Parts Only)

ANT Antiqued Brass Finish (Solid Brass Lanterns & Conversion Types Only)

RUST Rusted Finish (Use with Plain Trim Lanterns Only. Sealed with Lacquer)

SAND Sand blasted (Use with Plain Trim Lanterns Only. Not Sealed with Lacquer)

STRIP Stripped Lacquer (Use with Solid Brass Lanterns & Conversion Types Only to Remove Lacquer Finish)

COLOR Custom Enamel Finish (Specify Any Stock Color)

6

Socket Types (All Lanterns provided with E12/E26 Sockets Unless Specified Otherwise.)

DAMP Damp Location Socket & Wire (Limited Applications, Standard E-26 Edison Base Only)

E12/E26 American 110 Volt Candelabra/ Edison Base Sockets (Dry Location)

E14/E27 European 220 Volt Small/Medium Base Sockets

F Fluorescent (7 or 9 Watt PL Bulb, or Customer Specified)

MH Metal Halide 4KV PULSE RATED E-26 SOCKET ONLY, (Ask for Available Applications)

V Low Voltage Conversion (12 Volt Gy6.35 or Wedge Base)

WET Wet Location Socket & Wire (Limited Applications, Standard E-26 Edison Base Only)

7

Optional Globes FG Frosted Globe

FSG Frosted Sealed Globe

RED Red Globe

SG Sealed Clear Globe

8 Custom Specifications

Contact us for pricing and availability

9

UL Labeling (Optional)

DRY Dry Location (Indoors Applications)

DAMP Damp Location (Protected Outdoors Applications)

WET Wet Location (Exposed Outdoors Applications)

Aged Galvanized Aged Galvanized/TIN

Real Rust Antique Copper Plate

Semi-Flat Black Enamel Oxidized Nickel Plate

W. T. Kirkman No. 1 Little Champ & No. 20 Junior Lantern Fixtures Lantern Dimensions: Height: 12 Tank Diameter: 5 Overall Height with Bail Up: 16 Optional Down Light Can: Add 4 Standard Finishes: Bright or Aged Galvanized Semi-Flat Black Enamel Oxidized Nickel Plate Real Rust (Dry Locations Only) Textured Rust Enamel Custom Finishes Also Available Globe Finishes: Clear, Colored or Frosted A. No. 1-T-HR-FG Pendant Lantern w/ 10 Hooded Reflector B. No. 20-WR-FG-ON Wall Reflector Lantern C. No. 20-T-CB-HR Top Wired Concealed Bail Lantern w/10 Hooded Reflector D. No. 20-J-RUST J-Hook Wall Lantern E. No. 1-GPR-AGED-AMBER Gold Pan Wall Reflector Lantern F. No. 1-H-AGED Hook & Wall Canopy Lantern Electrical Specifications: Dry Location Versions: 60 Watt Max. Candelabra Bulb Damp Location Versions: 100 Watt Max. A-19 Bulb Optional Down Light: 40 Watt Max. R-20 Bulb 12 Volt Versions: Dry, Damp, or Wet Location: 21 Watt Max Wedge Base Socket/ 50 Watt Max. Bi-Pin GY6.35 Base

All Fixtures Available in O.E.M. or UL Listed Versions

19.

Aged Galvanized Textured Rust Enamel

Antique Brass Plate Semi-Flat Black Enamel

Aged Galvanized Semi-Flat Black Enamel

W. T. Kirkman No. 2 Champion & No. 80 Blizzard Lantern Fixtures Lantern Dimensions: Height: 15 Tank Diameter: 7 3/4 Overall Height with Bail: 21 1/2 Optional Down Light Can: Add 4 Standard Finishes: Bright or Aged Galvanized Semi-Flat Black Enamel Oxidized Nickel Plate Real Rust (Dry Locations Only) Textured Rust Enamel Custom Finishes Also Available Globe Finishes: Clear, Colored, or Frosted G. No. 2-P-HR-AGED Post Lantern w/ 12 Reflector H. No. 2-T-FG Top Wired Pendant Lantern I. No. 2-T-CB-HR Top Wired Concealed Bail Lantern w/12 Hooded Reflector J. No. 80-WR-D-FG Wall Reflector w/Down Light K. No. 80-WR Wall Reflector Lantern L. No. 2-WR-FG-AGED Wall Reflector Lantern Electrical Specifications: Dry or Damp Location: 100 Watt Max. A-19 Bulb Optional Down Light: 40 Watt Max. R-20 Bulb 12 Volt Versions: Dry, Damp, or Wet Location: 21 Watt Max Wedge Base Socket/ 50 Watt Max. Bi-Pin GY6.35 Base


20.

We Use Only American Made Solid Hickory

Wagon Wheels

Bright Galvanized Steel Semi-Flat Black Enamel

Aged Galvanized

Lantern Dimensions: Height: 12 Tank Diameter: 5 Optional Hooded Reflector: 10 D. Standard Finishes: Bright Galvanized Semi-Flat Black Enamel Custom Finishes: Aged Galvanized Oxidized Nickel Plate Antique Brass or Copper Plate Real Rust (Dry Locations Only) Textured Rust Enamel Other Custom Finishes Available Globe Finishes: Clear or Frosted

M. No. 1-T-HRx3-ST 36 Single Tree w/ 3 No. 1 Little Champs Overall Height 52 N. No. 20-WW-HRx6 Wagon Wheel Chandelier w/ 6 Point 36 Chain Kit w/ 6 No. 1 Little Champs Overall Height 42 O. No. 20-WW-HR-FGx18 3 Tier Wagon Wheel Chandelier w/ 4 Point Chain Kit w/ 18 No. 1 Little Champs Overall Height 108

Electrical Specifications: Dry Location Versions: 120 Volts, 60 Watt Max. E-12 Candelabra Base Bulb, or 220 Volts, 60 Watt Max E-14 European Candelabra Base Damp Location Versions: 120 Volts, 100 Watt Max. E-26 Medium Base Bulb (12 Volt Versions Also Available)

All Fixtures Available in

O.E.M. or UL Listed Versions

W.T. Kirkman No. 1 Little Champ Lantern Single Tree and Wagon Wheel Fixtures

21.

W. T. Kirkman No. 300 Frontier Street Lamps Standard Finishes: Semi-Flat Black Enamel Hammered Dark Green Hammered Brown Textured Rust Enamel Custom Finishes Also Available Dimensions: Post Size: 3 Diameter Reflector Diameter: 14 Post Lamp Height: 26 Hanging Lamp Height: 23 Pier Lamp Height: 19 Globe Finishes: Clear or Frosted P. No. 300-P Post Lamp Q. No. 300-PM Pier Mount Lamp R. No. 300-H Hanging Lamp S. No. 1880-E Dietz Style Wall Bracket Electrical Specifications: Damp Location Versions: 100 Watt Max. A-19 Bulb Wet Location Version: 100 Watt Max. A-19 Bulb 12 Volt Versions: 50 Watt Max. GY6.35 Bi-Pin

T he W. T. Kirkman No. 300 Frontier Lamp is patterned after the Dietz and C. T. Ham street lamps introduced in the 1880s. This type of lamp was used in the United States into the 1920s, and could be commonly found at railroad stations and platforms, army & cavalry bases, and courthouse and library entrances to name just a few. The W.T. Kirkman #300 Frontier is closer in appearance to the original patterns than any others made in the past 50 years.


Dietz Blue

Semi-Flat Black Enamel

Textured Rust Enamel

Hammered Brown

22.

#L01-BR-WF Amie Wall Fixture w/ 6" Brass Reflector Polished Solid Brass

#20M-TCB-D-ANT Matador

with Downlight Antiqued Solid Brass

#20M-GPR Matador Gold Pan

Wall Reflector Tin & Solid Brass

#2 Mars-TR-WF Mars Wall Fixture

Brass & Copper With Tin Reflector

#L01-BS-WF Amie Wall Fixture

with Blue Shade Polished Solid Brass

Specialty W. T. Kirkman Custom Fixtures All Fixtures Available in O.E.M. or UL Listed Versions, for use with 12, 120, and 220 Volts

#3-VIGILANT Hanging Lamp Fixture

with Down-Light Antiqued Solid Brass

#20M-TCB-ON Matador

Hanging Lamp Oxidized Nickel

#200-CPM-AC Prairie

Pier Mount Lamp Antiqued Copper

23.

O riginally founded as the Mantle Lamp Company of America in 1908 by Victor S. Johnson, (at right,) over 100 years later the Aladdin Mantle Lamp Company continues to fill the need for a superior non-electric light that is easy to use and works silently. Since the days under the leadership of V. S. Johnson, the company has gone through many changes and has produced millions of mantle lamps that continue to be used and sought the world over. Aladdin mantle lamps are the only non-pressurized mantle lamp made today, and are capable of producing light equivalent to a 40 to 50 Watt incandescent light bulb, making them an essential for off-grid living. Aladdin lamps can operate for 48 hours per gallon of lamp oil or kerosene, and produce over 3000 BTUs making them a great secondary heat source. In the world of oil lighting, there is no equal to the excellence and reliability of an Aladdin mantle lamp. We maintain one of the best selections of Aladdin mantle lamps and replacement parts in the U.S.A., only a portion of which are shown in this catalogue.

Aladdin #VB2312 Alexandria Table Lamp

Variations: #VB2312 Cobalt Lamp Only $216.95 w/ #401 Shade $259.95 w/ #501-9R Shade (Shown) $259.95 w/ #501-9RO Shade $259.95 #VC2312 Clear Lamp Only $206.95 w/ #401 Shade $249.95 w/ #501-9R Shade $249.95 w/ #501-9RO Shade $249.95

Aladdin #C6107 Genie III

Shelf or Wall Lamp

Variations: #C6107 Clear Lamp Only $129.95 #C6108 Brown Lamp Only $135.95 #C6110 Cranberry Lamp $135.95 Note: These lamps can be used with the #N118B Standard Wall Bracket, and the #P152-4B Deluxe Wall Bracket, or the #H715 Hanging Tilt Frame.

Aladdin #C6108 Genie III

Shelf or Wall Lamp

Variations: #C6107 Clear Lamp -100 w/ 12 White Shade $149.95 -100A w/ 12 Goose Shade $159.95 -100D w/ 12 Ship Shade $159.95 #C6108 Transparent Brown Lamp -100 w/ 12 White Shade $155.95 -100A w/ 12 Goose Shade $165.95 -100D w/ 12 Ship Shade $165.95

Aladdin #C6193 Lincoln Drape

Shelf Lamp

Variations: #C6193 Clear Lamp Only (Shown) $138.95 #C6193-100 w/ 12 White Shade $158.95

All Aladdin Mantle Lamps Available in Both Oil or Electric Versions. For Aladdin Mantle Lamp and Shade Variations not shown, call us toll free at 1-877-985-5267 or visit www.LanternNet.com

24.

Aladdin #C6192 Clear Short Lincoln Drape

Variations: #C6192 Lamp Only $199.95 #C6192-110 w/ 14 Plain White Shade $229.95 #C6192-144-01 Shown w/ 14 Fall Coach & Four Shade $234.95

Aladdin #C6177 Cobalt Short Lincoln Drape Variations: #C6177 Lamp Only $199.95 #C6177-144-02 Shown w/ 14 Winter Coach & Four Shade $234.95 #C6177-110W w/ 14 Pleated White Shade $239.95

Aladdin #C6188 Pink Short Lincoln Drape

Variations: #C6188 Lamp Only $199.95 #C6188-110P Shown w/ 14 Pleated Pink Shade $234.95

Aladdin #C6183N Amethyst Short Lincoln Drape Variations: #C6183 Lamp Only w/ Nickel Burner $229.95 #C6183-110W Shown w/ 14 Pleated White Shade $269.95

Aladdin #C6198 Emerald Short Lincoln Drape

Variations: #C6198 Lamp Only $199.95 #C6177-110W w/ 14 Pleated White Shade $239.95 #C6198-N388 14 Ducks Shade (Shown) #C6198-N399 w/ 14 Fox and Hounds Shade $229.95

Aladdin #C6195 Ruby Short Lincoln Drape

Variations: #C6195 Lamp Only $219.95 #C6195-110W w/ 14 Pleated White Shade $259.95 #C6195-N399 Shown w/ 14 Fox and Hounds Shade $249.95

Aladdin #R011 Alacite Florentine Vase

Variations: #R011 Lamp Only $209.95 #R011-SL305K Shown w/ 12 Jon Paul Shade $279.95 #R011-SL205K 14 Jon Paul Shade P.O.A. Other Shade Options Available

Aladdin #R010 Moonstone Florentine Vase

Variations: #R010 Lamp Only $209.95 #R010-SL303K Shown w/ 12 Seth Andrews Shade $279.95 #R010-SL203K 14 Seth Andrews Shade P.O.A. Other Shade Options Available

25.

All Lamps Available in Oil or Electric Versions. More Aladdin Mantle Lamp and Shade Variations Shown at www.LanternNet.com

(Call us toll free at 877-985-5267 for Aladdin Lamp models not shown.)

Aladdin #K102 Polished Brass Classic Lamp

Variations: #K102 Polished Brass Classic Lamp Only #K102-N201 Opal Models 1 Through 5 Shade #K102-300 Opal Ribbed Shade #K102-301 Green Ribbed Shade #K102-302 Red Ribbed Shade (Shown) #K102-303 Amber Ribbed Shade #K102-392 Opal Swirl Shade #K102-S401R Opal Model 7 & 8 Shade #K102-501-9R Crystal/Clear Model 9 Shade #K102-540 Opal Student Shade #K102-550-1 Opal Swiss Shade #K102-M570 Green Melon Shade #K102-M571 Ruby Melon Shade #K102-601 Crystal/Clear Model 12 Shade #K102-N653 Opal Model 12 Shade #K102-672 Champagne Model 12 Shade #K102-N701 Opal Model B Shade #K102-N710 Opal Taper Shade

Aladdin #BK1082 Polished Brass Parlor Lamp

Variations: #BK1082 Polished Brass Parlor Lamp Only #BK1082-M200 White Artichoke Shade #BK1082-M201 Green Artichoke Shade (Shown) #BK1082-M202 Ruby Artichoke Shade #BK1082-M203 Amber Artichoke Shade Other Shade Options Available

Aladdin #B2301 Polished Brass Heritage Lamp

Variations: #B2301 Polished Brass Heritage Lamp Only #B2301-N201 Opal Models 1 Through 5 Shade #B2301-300 Opal Ribbed Shade #B2301-301 Green Ribbed Shade #B2301-302 Red Ribbed Shade #B2301-303 Amber Ribbed Shade #B2301-392 Opal Swirl Shade #B2301-S401R Opal Model 7 & 8 Shade #B2301-501-9R Crystal/Clear Model 9 Shade #B2301-540 Opal Student Shade #B2301-550-1 Opal Swiss Shade #B2301-M570 Green Melon Shade (Shown) #B2301-M571 Ruby Melon Shade #B2301-601 Crystal/Clear Model 12 Shade #B2301-N653 Opal Model 12 Shade #B2301-672 Champagne Model 12 Shade #B2301-N701 Opal Model B Shade #B2301-N710 Opal Taper Shade

All Lamps Available in Oil or Electric Versions. More Aladdin Mantle Lamp and Shade Variations Shown at www.LanternNet.com

Aladdin #SS2301 Stainless Steel Heritage Lamp

Variations: #SS2301 Stainless Steel Lamp (Shown at Left) #SS2301-300 Opal Ribbed Shade #SS2301-301 Green Ribbed Shade #SS2301-302 Red Ribbed Shade #SS2301-303 Amber Ribbed Shade #SS2301-392 Opal Swirl Shade #SS2301-540 Opal Student Shade #SS2301-M570 Green Melon Shade #SS2301-M571 Ruby Melon Shade #SS2301-N653 Opal Model 12 Shade #SS2301-N701 Opal Model B Shade #SS2301-N710 Opal Taper Shade Other Shade Options Available

Genuine Aladdin Lamp Oil Genuine Aladdin Lamp Oil is the finest non-paraffin distilled lamp oil made today in the U.S.A. #AML17552-QT 12 per Case #AML17554-GL 4 per Case

(Call us toll free at 877-985-5267 for Aladdin Lamp models not shown.)

Aladdin #H715 Polished Brass Tilt-Frame Lamp

Variations: #H715-C6107 Clear Lamp, No Shade #H715-C6107-N110 w/ White Shade #H715-C6107-N388 w/ Ducks Shade (Shown) #H715-C6108 Trans. Brown Lamp, No Shade #H715-C6108-N110 w/ White Shade #H715-C6108-N209 w/ Log Cabin Shade #H715-C6108-N399 w/ Fox & Hounds Shade #H715-C6109 Green Moonstone Lamp, No Shade #H715-C6109-N110 w/ White Shade #H715-C6109-N388 w/ Ducks Shade Other Shade Options Available

Aladdin #P152-4 Polished Cast Brass Bracket Lamp

Variations: #P152-4B Brass Lamp, No Shade #P152-4B-N201 Opal Models 1 Through 5 Shade #P152-4B-300 Opal Ribbed Shade #P152-4B-301 Green Ribbed Shade #P152-4B-302 Red Ribbed Shade (Shown) #P152-4B-303 Amber Ribbed Shade #P152-4B-4B-392 Opal Swirl Shade #P152-4B-S401R Opal Model 7 & 8 Shade #P152-4B-501-9R Crystal/Clear Model 9 Shade #P152-4B-540 Opal Student Shade #P152-4B-550-1 Opal Swiss Shade #P152-4B-M570 Green Melon Shade #P152-4B-M571 Ruby Melon Shade #P152-4B-601 Crystal/Clear Model 12 Shade #P152-4B-N653 Opal Model 12 Shade #P152-4B-672 Champagne Model 12 Shade #P152-4B-N701 Opal Model B Shade #P152-4B-N710 Opal Taper Shade Other Shade Options Available

Aladdin #N118 Standard Wall Bracket Lamp

Polished Brass Variations: #N118B-C6107 Clear Lamp, No Shade #N118B-C6107-N110 w/ White Shade #N118B-C6107-N388 w/ Ducks Shade #N118B-C6108 Trans. Brown Lamp, No Shade #N118B-C6108-N110 w/ White Shade #N118B-C6108-N209 w/ Log Cabin Shade #N118B-C6108-N399 w/Fox & Hounds Shade, Shown

Aladdin #N118 Standard Wall Bracket

#N118B Polished Solid Brass #N118N Nickel Plated Steel Post-1947 Style Includes screws

Aladdin #BH210 Polished Brass Model 6 Style

Deluxe Hanging Lamp

Variations: #BH210-Opal Shade #BH210-Green Shade

Aladdin #P152-4 Deluxe Wall Bracket

#P152-4B Polished Solid Brass #P152-4N Nickel Plated Brass Post-1908 Style Includes screws

27.

Aladdin Lamp Wicks #R151 (Fits Models A, B, C, & 14) #N198 (Fits Models 7 Through 12) #R199 (Fits Models 21 & 21C) #N230 (Fits Models 23, 23A & 23E60)

Aladdin Lamp Chimneys #R103 Premium Grade Lox-On #N910-2 Premium Grade Heelless 2 5/8 x 12 1/2 #R905 High Altitude Heelless 2 5/8 x 15

Aladdin Light Boosters #N108B Bright Brass #N108N Nickel Plated For use above 3000 elevation on all Aladdin Chimneys

Aladdin Smoke Bell

#N102-1A Polished Brass Replacement for Tilt-Frame and hanging harp lamps

Aladdin Bug Screens #N103B Bright Brass #N103N Nickel Plated #N103P Black Pearl

Aladdin Lamp Mantles #R150 Lox-On Style Mantle (Shown) (Fits Models A, B, C, 14, 21, 21C, 23, and 23A) #N146-1A Kone-Kap Style Adapter (Fits Models 3 through 12)

Aladdin Wall Plates

#153-1RB Polished Brass #153-1RN Nickel Plated Brass (Fits Bracket No. P152-4)

Aladdin Machined Filler Plugs

5/8" diameter, 20 T.P.I. #N114B Polished Solid Brass

Aladdin Stamped Filler Plugs

11/16" diameter, 16 T.P.I. #N115A Aluminum #N115B Polished Brass #N115N Nickel Plated #N115RG Rubber Gasket #N121AB Brass Filler Collar #N121AN Nickel Filler Collar

Aladdin Stamped Filler Caps

Nominal 1 1/16" I.D. #N120B Polished Brass #N120N Nickel Plated #N120CG Cork Gasket #N121B Brass Filler Collar #N121N Nickel Filler Collar

Aladdin Paper Shade Clips

#N102-2 Paper Shade Clips for 14" Parchment Shade for Hanging Lamps on #H715 Tilt Frame (Set of Three)

Aladdin Smoke Bell

#960-B Bright Solid Brass Fits all chimneys with 2 top diameter

28.

Aladdin Lox-On Burners #N236B Bright Brass #N236N Nickel Plated

Aladdin Wick Cleaner #R111 Use with all Aladdin models that use 1 round wick.

Aladdin Flame Spreader #N106 Bright Brass (Models 12,14, A, B, C, 21, 12c, 23, 23A & 23E60)

Aladdin Heelless Electric Adapters

#N186B Bright Brass #N186N Nickel Plated #N186SS Stainless Steel #N908B Brass w/Round Knob

Lox-On Electric Adapters #N185B Bright Brass #N185N Nickel Plated

B Style Electric Adapters

#N195B Bright Brass #N195N Nickel Plated (Custom Electric Adapters Made Upon Request)

Aladdin Heelless Burners

#N236AB Bright Brass #N236AB-PL Polished Brass #N236AN Nickel Plated

Genuine Aladdin Brand Replacement Parts assure like-new performance. (Call for Aladdin parts not shown.)

Aladdin 10 Shade Rings

#1080BR Polished Brass #1080N Nickel Plated #1080SS Stainless Steel #401RB Brass Plated Steel

Aladdin Model C Gallery

#N191N Nickel Plated Steel Fits Model C burners made in Brazil only

Aladdin Tripod Shade Rings

#1281B 12 Polished Brass #1281N 12 Nickel Plated #1478B 14 Polished Brass #1478N 14 Nickel Plated

Aladdin Heelless Gallery

#N239AB Bright Brass #N239AN Nickel Plated

Aladdin Model B Lox-On Gallery

#N192B Bright Brass #N192N Nickel Plated

Aladdin Lox-On Gallery

#N239B Bright Brass #N239N Nickel Plated

Aladdin Outer Wick Tube #N238B Bright Brass #N238N Nickel Plated

Aladdin 23 Wick Raiser #N233 (Models 21, 21c, 23 and 23A Burners Only)

Aladdin B Wick Raiser #R185 (Models B and English 14 Burners Only)

Aladdin C Wick Raiser #R188 (Model C Burners Only)

29.

Properly Adjusted Kosmos Burner

Important Note

Oil Lamp and Lantern burners will continue to heat up and become more efficient after lighting. Do not make your final adjustment until after 10 minutes, or a high,

sooty flame may result.

HOW TO REPLACE WICK To replace the wick in a Kosmos burner, first you must remove the shade and/or chimney and then un-screw the burner from the fount. Discard the old wick. Insert the corners of one end of the wick into the wick channel in the bottom of the burner, then tilt the wick into place. Rotate the wick ad-juster knob clockwise, making sure that both cogs engage the wick simultaneously so that the wick tracks evenly. Before fueling your lamp, trim the wick by burning it DRY until it is consumed evenly to the top of the burner tube. Allow the new wick to completely saturate for 20 minutes before lighting.

W. T. Kirkman Oil and Electric Lanterns is proud to be the exclusive U.S.A. wholesale Distributor for Gaudard Fine Products

The Most Complete Source for Genuine Kosmos Oil Lamps and Parts in the U.S.A.!

In 1869, Auguste Gaudard set up his first die stamping shop in the Jura region of France. In 1902, a modern factory was established in Morbier, France with 30 draw presses that were purchased in Brooklyn, New York, and Auguste began production of his first oil lamps. The factory has now been in continuous operation under five generations of the Gaudard family. Today, the Gaudard Factory produces some of the finest oil lamps and burn-ers made using modern machinery with only the best raw materials and strict quality control at every stage of the process. The finishing touches are still done by craftsmen just as was done over 100 years ago.

FUEL INFORMATION Oil lamps with Kosmos & Matador burners can use standard clear lamp oil (such as Medallion or Crown Brands,) (Not Paraffin Oil or Ultra-Pure.) They can also be used with Minimum 125 Test Clear Kerosene, or synthetic kerosene, such as Klean-Heat or Clear-Lite.

NOTE: 99% Paraffin Oil (Ultra-Pure, Nowells, Tropical Lights, etc.) will not burn properly in oil lamps with a Kosmos or Matador Burner due to their high flash point and viscosity. WARNING: NEVER USE THE FOLLOWING IN ANY WICK LAMP OR LANTERN OF ANY TYPE: Gasoline, Coleman Fuel, White Gas, Paint Thinner, (Mineral Spirits,) Wood Alcohol, Naptha, Turpentine, Benzene, or any other fuel with a Flash Point lower than 125 Fahrenheit, PROPERTY LOSS, SERIOUS INJURY, OR DEATH CAN RESULT .

30.

W.T. Kirkman is the Exclusive USA Distributor for Gaudard Fine Products No Minimum Order/No Broken Case Fee

KOSMOSLAMPS.com Toll Free 1-877-985-5267 Fax 760-789-2379

L01 Amie Brass Lamp L01W Amie Wall Lamp

T his simple yet elegant oil lamp features all brass or copper con-struction and is fitted with a genuine #14 Kosmos burner and chimney. The Amie Lamp can be ordered with a hand blown Etched Glass Ball Shade which compliments the lamp nicely. A 36 minimum vertical clearance is re-quired. The addition of a clip-on Smoke Bell is also recommended to deflect heat. SPECIFICATIONS: Overall Lamp Height 15 1/2 Fuel Capacity 20 oz. Approx. Burn Time: 11 Hours Approx. Output 14 Watts LAMP VARIATIONS: Brass Lamp Only L01 w/ 5 1/4 Etched Ball Shade L01-EB01 Wall Lamp w/Reflector L01W Copper Lamp Only L01C w/ 5 1/4 Etched Ball Shade L01C-EB01

T he "Alice" lamp is similar to the "Amie," but has a more imposing presence due to the addition of a pedes-tal base. It is fitted with a genuine #14 Kosmos burner and chimney, and can be ordered with a hand blown Etched Glass Ball Shade which compliments the lamp nicely. A 36 minimum verti-cal clearance is required. The addition of a clip-on Smoke Bell is also recom-mended to deflect heat. SPECIFICATIONS: Overall Lamp Height 17 1/2 Fuel Capacity 20 oz. Approx. Burn Time: 11 Hours Approx. Output 14 Watts LAMP VARIATIONS: Brass Lamp Only L24 w/ 5 1/4 Etched Ball Shade L24-EB01 Copper Lamp Only L24C w/ 5 1/4 Etched Ball Shade L24C-EB01 L24-EB01 Alice Brass Lamp

w/ Ball Shade L24 Alice Brass Lamp

31.

W.T. Kirkman is now the Exclusive USA Distributor for Gaudard Fine Products No Minimum Order/No Broken Case Fee


L05H-BS Cottage Lamp w/ White Shade L05H-GS Cottage Lamp w/Green Shade

D esigned to be suspended from a ceiling hook, the Cottage lamp is ideal for use above a desk or table. Fea-tures a solid brass frame with an inte-grated smoke bell. Includes 3 of brass chain. SPECIFICATIONS: Overall Lamp Height 28 Fuel Capacity 20 oz. Approx. Burn Time: 11 Hours Genuine #14 Kosmos Burner Approx. Output 14 Watts LAMP VARIATIONS: with Blue Student Shade L05H-BS with Green Student Shade L05H-GS with White Student Shade L05H-WS with 6 Etched Ball Shade L05H-EB02 without Shade L05H Lamp Only, No Hanger L05

O ne of the most popular lamps in our line, the Charmante is a pleasing blend of artistic touches of iron and solid brass. This elegant lamp can be sus-pended over a table from a chain or hung on your wall using the hand made iron wall bracket. Features include a solid brass reflector and an integrated smoke bell. SPECIFICATIONS: Lamp Height 16 Overall Height with Wall Hook 21 Fuel Capacity 6 oz. Approx. Burn Time: 7 Hours Genuine #6 Kosmos Burner Approx. Output 6 Watts LAMP VARIATIONS: Hanging Lamp L-06H Hanging Lamp w/ Wall Hook L-06W Insert Lamp Only L-M03

Use as a replacement in small marine signal lamps, but is equally suited for stand alone use. Features solid brass con-struction and a "Perceo" chimney. SPECIFICATIONS: 5 1/2" Overall Height 3 1/4" Bottom Diameter Average 2 Candle Power, 6.35mm Round Wick #5 Mini Burner



32.

T he Patronne is a smart looking and graceful pedestal lamp that elevates the burner so abundant light is dispersed throughout the room. This elegant lamp is even more striking when complimented with one of the optional shades. SPECIFICATIONS: Overall Height 19 Fuel Capacity 26 oz. Approx. Burn Time: 16 Hours Genuine #14 Kosmos Burner Approx. Output 14 Watts LAMP VARIATIONS: POLISHED BRASS Lamp Only (Solid Brass) L-34 with 6 Etched Ball Shade L-34-EB02 with Blue Student Shade L-34-BS with Green Student Shade L-34-GS with White Student Shade L-34-WS LAMP VARIATIONS: PATINA FINISH SOLID BRASS Lamp Only (Solid Brass) L-34P with 6 Etched Ball Shade L-34P-EB02 with Blue Student Shade L-34P-BS with Green Student Shade L-34P-GS with White Student Shade L-34P-WS LAMP VARIATIONS: SOLID COPPER Lamp Only (Solid Copper) L-34C with 6 Etched Ball Shade L-34C-EB02 REPLACEMENT PARTS: Chimney CH14 Burner (Polished or Patina) B14 Wick W14 Clip-On Smoke Bell SB Brass Shade Tripod Support STS Cased Blue 7.5 Student Shade BS Cased Green 7.5 Student Shade GS Cased White 7.5 Student Shade WS 6 Dia. Etched Ball Shade EB-02

L34 Solid Brass

Patronne Lamp Available in Polished or Patina Finish

L34-GS Patronne Lamp in Polished Finish

Available with White, Blue, or Green Student Shade

L34-EB02 Patronne Lamp

with 6 Etched Ball Shade Available in Polished or Patina Finish

L34P-WS Patronne Lamp in Patina Finish

Available with White, Blue, or Green Student Shade



33.

T he patina finish of the "DeVerre" oil lamp adds to its old world charm. Constructed of hand blown glass and solid brass, it features a weighted base and #14 Kosmos Burner. This heirloom quality lamp will give years of faithful service. Makes a wonderful gift! SPECIFICATIONS: Overall Height 18 7/8 Overall Height 4 7/8 Fuel Capacity 24 oz. Approx. Burn Time: 13 Hours Genuine #14 Kosmos Burner Approx. Output 14 Watts

LAMP ONLY VARIATIONS: PATINA FINISH SOLID BRASS Lamp Only (Amber) L-08A Lamp Only (Blue) L-08B Lamp Only (Green) L-08G Lamp Only (Rose) L-08R LAMP WITH SHADE VARIATIONS: PATINA FINISH SOLID BRASS with 6 Etched Ball Shade L-08A-EB02 with 6 Etched Ball Shade L-08B-EB02 with 6 Etched Ball Shade L-08G-EB02 with 6 Etched Ball Shade L-08R-EB02 REPLACEMENT PARTS: Kosmos Chimney CH-14 Kosmos Burner (Patina) B14-P Matador Chimney CH-15 Matador Burner (Patina) B15-P Wick W14 Clip-On Smoke Bell SB-P Brass Shade Tripod Support STS-P Cased Blue 7.5 Student Shade BS Cased Green 7.5 Student Shade GS Cased White 7.5 Student Shade WS 6 Dia. Etched Ball Shade EB-02

L08B Blue DeVerre Lamp

in Patina Finish

L08R-EB02 Rose DeVerre Lamp in Patina Finish

with 6 Etched Ball Shade

L08A Amber DeVerre Lamp

in Patina Finish

L08G-EB02 Green DeVerre Lamp in Patina Finish

with 6 Etched Ball Shade

34.



L44BP-EB02 Black Pearl Concierge Lamp with 6 Ball Shade

T he broad popularity of the "Concierge" lamp stems from its combination of features. It has a pleasing low profile for stability, and a sturdy handle that doubles as a wall bracket. A clip-on smoke bell, available separately, is recommended when you have limited overhead clearance. SPECIFICATIONS: Overall Height 15 Fuel Capacity 30 oz. Approx. Burn Time: 16 Hours Genuine #14 Kosmos Burner Approx. Output 12 Watts LAMP VARIATIONS: POLISHED BRASS L44 Lamp Only (Solid Brass) L44-EB02 w/ 6 Etched Ball Shade L44-BR w/ 6 1/2 Brass Reflector PATINA FINISH SOLID BRASS L44P Lamp Only (Solid Brass) L44P-EB02 w/ 6 Etched Ball Shade L44P-BR w/ 6 1/2 Brass Reflector BLACK PEARL FINISH OVER BRASS L44BP Lamp Only (Solid Brass) L44BP-EB02 w/ 6 Etched Ball Shade REPLACEMENT PARTS: Chimney CH14 Burner (Specify Finish) B14 Wick W14 Clip-On Smoke Bell SB 6 Dia. Etched Ball Shade EB-02

L44 Polished Solid Brass Concierge Lamp

L44P Patina Finish Solid Brass Concierge Lamp

L44-BR14 Solid Brass Concierge Lamp with 6 Reflector

#BR14 Reflector 6 1/2 Dia. Brass Side Reflector Use with #14 Burners W.T. Kirkman Exclusive Made in the U.S.A.

35.



T he Vintner lamp features a #13 solid round wick and spherical chimney for protection from drafts. This lamp offers the intimacy and warmth of candlelight without the hazards of dripping wax and instability. Features a carrying handle with keyhole slot for hanging on the wall if desired. Embossed with a mark of authenticity. Originally designed for candling fine wines, but equally suited for ambiance lighting. SPECIFICATIONS: Solid Brass Vintner Lamp L13 Copper Plated Brass Vintner Lamp L13C Lamp Height 10 1/2 Fuel Capacity 10 oz. Approx. Burn Time: 10 Hours Approx. Output 1 Watt REPLACEMENT PARTS: Chimney CH-13 Burner B-13 Wick W-13

T he solid brass Maitresse lamp features a "Bombe" chimney with a #6 Kosmos burner, while the Maitresse Boule lamp features a #6 Kosmos chimney and a 4 1/4" diameter etched ball shade. Both lamps feature a carrying handle with keyhole slot for hanging on the wall if desired. SPECIFICATIONS: Fuel Capacity 10 oz. Approx. Burn Time: 5 Hours Approx. Output 6 Watt LAMP VARIATIONS: Maitresse Lamp L12 Lamp Height 12 Maitresse Boule Lamp L12-EB00 Lamp Height 14 REPLACEMENT PARTS: #6 Bombe Chimney CHB-06 #6 Kosmos Chimney CH-06 4 1/4 Ball Shade EB-00 #6 Kosmos Burner B-06 #6 Wick W-06

36.



Genuine Solid Brass Replacement Burners w/ Wick, polished finish unless noted. Replacement collars sold separately. Made by Gaudard in France #B06 Kosmos Burner (Collar 1 1/2 I.D.) #B08 Kosmos Burner (Collar 1 5/8 I.D.) #B10 Kosmos Burner (Collar 2 I.D.) #B12 Kosmos Burner (Collar 2 1/8 I.D.) #B13 Vintner Burner #B14 Kosmos Burner (Collar 2 1/8 I.D.) #B14C Kosmos Burner-Copper #B14P Kosmos Burner-Patina Finish #B15 Matador Burner (Collar 2 1/8 I.D.) #B20 Matador Burner (Collar 2 1/8 I.D.)

#GE14 Electric Gallery Adapter Our #GE14 electric gallery adapter can be used with any lamp that uses a #14 Kosmos burner. Permits use of lamp with electricity with no drilling required. Allows quick change back to oil use and vice versa. Features solid brass construction, a 7 polar-ized cord with line switch. Also in-cludes a 60 Watt Candelabra Base bulb, maximum. (#14 Burner gallery sold separately, if required.) SPECIFICATIONS: Brown, White, or Gold Cord W.T. Kirkman Exclusive Assembled in U.S.A. with imported and domestic parts

Genuine O.E.M. Violet Stripe Kosmos Tight Weave Wick. Highest Quality assures like new operation. Satisfaction Guaranteed! #W06 35mm Width (1 3/8" Approx.) #W08 42mm Width (1 5/8" Approx.) #W10 48mm Width (1 7/8" Approx.) #W12 54mm Width (2 1/8" Approx.) #W13 7.00mm Dia. (9/32 D. Approx.) #W14 65mm Width (2 9/16" Approx) Made in Great Britain

#SM-14 Smoke Bell Clip-On Smoke Bell Polished Solid Brass Fits all Kosmos table lamps Made in India Use on Lamps with low overhead clearance

CHIMNEYS #CHB-06 Bombe Chimney 1 3/8 Fitter, 8 1/4 Height Fits the Charmante and Maitresse Lamps #CH-6 Kosmos Chimney 1 3/8 Fitter, 6 1/2 Height Fits the Maitresse Boule Lamp #CH-8 Kosmos Chimney 1 7/16 Fitter, 8 3/8 Height #CH-10 Kosmos Chimney 1 9/16 Fitter, 9 7/8 Height Fits the European Hanging Lamp #CH-12 Kosmos Chimney 1 5/8 Fitter, 10 Height #CH-13 Vintner Chimney 1 1/4 Fitter, 3 5/8 Height Fits the Vintner Lamp #CH-14 Kosmos Chimney 2 1/8 Fitter, 10 1/4 Height Fits the Amie, Alice, Concierge, and Patronne Lamps #CH-15 Matador Chimney 2 1/8 Fitter, 10 1/2 Height #CH-20 Matador Chimney 2 9/16 Fitter, 11 Height Hand Blown Etched Ball Shades #EB-00 Shade 4 1/4 Diameter (Fits #6 Burner) #EB-01 Shade 5 1/4 Diameter (Fits #14 Burner) #EB-02 Shade 6 Diameter (Fits #14 Burner) Cased Glass Student Shades #BS 7.5 Blue Student Shade #GS 7.5 Green Student Shade #WS 7.5 White Student Shade

37.



WTK2001 DIETZ JUNIOR TRADE CARD PRINT 8 1/2 x 11 Full Color Reprint of a Circa 1910 Dietz Junior Trade Card. Printed on acid free paper, suitable for fram-ing. Great item for collectors.

Lanterns that Lit Our World One of the first books on the topic. A good introductory book that covers the basics. Includes catalog illustrations for Dietz, Adlake, and other lantern manufacturers. (Please Note: This book has not been updated since it was first published over 25 years ago, and does contain some factually in-correct data.) No. 4867 Published by Golden Hill Press B&W 6 x 9 Paper Back, 231 Pgs.

Lantern Enlightenment 1995 Edition Linda Blacks hard to find book has dozens of detailed technical line drawings, vintage lantern advertisements, and a lantern col-lector's check list. A must have book for the serious collector. No. 3070 Published by Craftsmen Photo Lithographers B&W, 8" x 11 Paper Back, 85 Pgs

Collectable Dietz Lanterns 1917 Catalog Reprint Features original descriptions, specifications, and illustrations of Dietz lanterns, accessories, and replacement parts from 1917. A must have book for serious and beginner collectors alike. Contem-porary values are provided for collectors. No. 1105 Published by Schiffer Books B&W, 5.5 x 8.5 Paper Back, 140 Pgs

Aladdin The Magic Name in Lamps A complete history of Aladdin kerosene and electric lamps pre-sented by Dr. J.W. Courter. Packed with both black and white and color photos and vintage ad-vertisements and catalog pages. Deluxe hardbound edition. No. 887923 Published by Wallace-Homestead Color/B&W, 9" x 11 Hardcover, 304 Pgs

Collectable Lanterns Many styles of lanterns are cov-ered from makers such as Dietz, Adlake, Embury, etc.; Household, Railroad, Marine, Tubular, Barn Lanterns, Signal Lamps, etc.. 100's of b/w Photographs and original catalog illustrations to help iden-tify lanterns. Contemporary values are provided for collectors. No. 1048A Published by Schiffer Books B&W 9" x 11" Paper Back 144 Pgs

Classic Lanterns, 2nd Edition One of the best books on the sub-ject. Over 200 photos and illustra-tions, over 30 color photos. De-tailed restoration information, American and foreign lanterns, railroad lanterns, and lots of barn lanterns. Collecting tips, quick reference prices, and a Universal Value Calculator. No. 3491 Published by Schiffer Books Color/ B&W 9" x 11 Paper Back, 141 Pgs

Aladdin Collectors Manual & Price Guide This is Dr. J.W. Courters match-ing price guide to Aladdin The Magic Name in Lamps, complete with photos, stock numbers, and market values. A must for every Aladdin collector. No. ACH22 Published by J.W. Courter B&W, 5.5 x 8.5 Paperback, 48 Pgs

38.

#CD1913DIETZ R.E. Dietz Co. 1913 Catalog & Price List I.G.L.R. Series Over 200 pages (PDF Format,) of Full Color scans of the complete Dietz No. 43. Catalog A rare reference and great resource for lan-tern collectors.

#CD1921DLSC Defiance Lantern & Stamping Company 1921 Catalog W.T. Kirkman Archive Series. Over 40 pages (JPG Format,) of full color scans of the 1921 DL&S Co. Catalog and price list. Binder label included.

CD1926DIETZ R.E. Dietz Co. 1926 Catalog No. 51 & 1927 Price List W.T. Kirkman Archive Series. Over 80 pages (JPG Format,) of Full Color scans of the 1926 R.E. Dietz Catalog and price list. Also included is a Little Giant ad which debuted in 1927. The last "Big" lantern catalog published by Dietz. A rare reference and great resource for lantern collectors. Binder label included.

CDEMBURY Embury Mfg. Co. 1908-1953 Catalogs, Price Lists, Advertisements, Etc. Over 300 pages com-bined (JPG Format,) of Full Color scans from the Embury Archive. Included are circa 1912, 1915, and 1917 Cata-logs, Price Lists, "Fly-Sheet" product flyers, photographs of the fac-tory in operation, news-paper clippings, electric flashlight ads, and much more. The best resource on Embury products. Binder label included.

#CD1883SGL Steam Gauge & Lantern Company 1883 Catalog W.T. Kirkman Archive Series. 100 pages (JPG Format,) of Full Color scans of the 1883 Steam Gauge & Lantern Co. Catalog. Binder label included.

#CD1914HAM C.T. Ham Mfg. Co. 1914 Catalogs & Price List I.G.L.R. Series Over 100 pages (PDF Format,) of Full Color scans of the complete 1914 C.T. Ham Lantern Catalog. (The last Ham catalog before being purchased by Dietz.)

CD1915PRISCO Pritchard Stamping Co. (Prisco) & Rayo Co. 1915 Catalogs W.T. Kirkman Archive Series. Over 80 pages(JPG Format,) of Full Color scans of both the Pritchard Strong Co. (Prisco) and Rayo (Standard Oil Company, aka Socony,) Lantern Catalogs from 1915. Binder labels included.

CDPATENTS U.S. Patent Office Archive Letters Patents Illustration Pages" Over 600 B&W illustra-tion pages for patents issued to: Adams and Westlake, R.E. Dietz., Charles and Lewis Betts, C.T. Ham, Steam Gauge & Lantern Co., John Irwin, Lovell-Dressel, Embury Mfg. Co., Pritchard Stamping Co., Winfield Mfg. Co., Wheeling Stamping Co. A must-have for the serious researcher or collector. Binder label included.

#CDOLLWW Ontario Lamp & Lantern Co. 1914, Warren Stamping Co., Winfield Mfg. Co 1916 I.G.L.R. Series Over 200 pages (PDF Format,) of Full Color and Grayscale scans. A rare reference and great resource for lantern collectors.

CDDML R.E. Dietz Co. 1903-1942 Motor Lamp Catalogs & Advertisements, Etc W.T. Kirkman Archive Series. Over 100 pages (JPG Format,) of full color scans of motor & marine lamp ephemera. Includes 1936 Volun-teer Fire Extinguisher catalog page, Eureka and Runabout Search-light Instructions, and over two dozen assorted advertisements from 1903 to 1921. Binder labels included.

39.

QUESTION: What is the difference between Hot Blast and Cold Blast Tubular lanterns? ANSWER: Tubular Lanterns are roughly classified under the captions "Hot Blast" and "Cold Blast." Dietz (Rhymes with beets,) made the first "Hot Blast" Lanterns in 1868, and the first "Cold Blast" Lanterns in 1880. The terms "Hot Blast" and "Cold Blast" are used solely in conjunction with tubular Lanterns and with regard to the method of supplying air to the flame. All other lanterns made are classified as "Dead Flame," which are nothing more than an enclosure to protect the flame, as no air circulation is provided. Dead Flame examples include the Adlake #300 Kero or Dietz #041 Railroad Lanterns. All Tubular Hot Blast and Cold Blast lanterns will self extinguish if tipped over. This safety feature is not found in any other type of oil burning lamp or lantern! Hot Blast Lanterns are so constructed that a supply of fresh air enters the globe at the base through the openings in the perforated globe plate. This fresh air, in ascending through the globe, becomes heated by the flame and mingles with the hot products of combustion. A portion of this mixture of hot air and spent gases passes into the bell or canopy over the globe and through the side tubes via downdraft to the air chamber beneath the burner, there directly supplying the flame. This design produces a steady yellow flame. Inherent in the design of the Hot Blast Lantern, the burning time is approximately 10% greater than a Cold Blast Lantern of the same wick size. Also, due to the re-circulating of the products of combustion, the Hot Blast Design is especially well suited for use indoors. Cold Blast Lanterns are so constructed that the supply of air taken through the side tubes does not mingle with the products of combustion and the flame is supplied with fresh air both through the globe plate and the side tubes. The spent products of com-bustion escape to the outer air through a central metal chimney in the Lantern head. From an air chamber surrounding the metal chimney, which is provided with injectors for taking in fresh air. The fresh air is then taken into the side tubes where it then flows to the lower air chamber and thus to the burner. The "Cold Blast" Lantern design produces a perfectly white flame and approxi-mately twice the volume of light of a "Hot Blast" Lantern with the same size wick. This fact has rendered the "Cold Blast" Lantern a favorite with users. With the advent of modern fuels, Cold Blast lanterns can be used inside or out.

QUESTION: How do I change the wick in my lantern? ANSWER: First you must remove the globe and then the burner. Discard the old wick after removing it from the burner. Trim the new piece of wick straight across, then apply 1/4 " of a 3" strip of masking tape to one end of the wick, and fold the tape back onto itself and wick, making a 1 1/4" long leader. Trim the masking tape to the width of the wick, and insert it into the underside of the burner using it to guide the wick. Once the wick is through the burner remove the tape and re-trim the wick straight across if necessary. This method can also be used for round wick using a narrow strip of masking tape as a leader.

QUESTION: How safe are tubular lanterns? Can I use them indoors? ANSWER: Contrary to Hollywood propaganda, tubular lanterns are infinitely safer than any other non-electric artificial light source. If a tubular lantern is tipped over, the balanced draft cuts off the air supply to the burner and extinguishes the flame within seconds. With the advent of modern lamp oil and synthetic kerosene, both Hot Blast and Cold Blast lanterns are well suited for indoor use in ventilated areas. Since the design of a Hot Blast lantern re-circulates spent air to the burner for more complete combustion, it has a slight edge over the Cold Blast Design, and a 10% greater efficiency rating. For light output how-ever, cold blast lanterns remain the best choice. QUESTION: How do I stop a tubular lantern from leaking oil from the air tube? ANSWER: In use, lantern wick conducts heat into the oil, this in turn creates expansion, and will cause oil to overflow into the air chamber under the burner if the lantern has been overfilled. Once this happens, the oil will leak out of the joints where the air tubes go into the air chamber above the tank. To prevent this, only fill the lantern to just under the fuel spout threads. Use a small white plastic kitchen funnel to more easily see the fuel level when filling. As a precaution, place the lantern in a shallow pan when re-fueling. If overfilling occurs, empty some of the fuel.

QUESTION: How do I stop a tubular lantern from leaking from the tank? (NOTE: Take all safety precautions, use rubber gloves, safety glasses, etc.) ANSWER: Remove the burner and fuel cap, and empty the oil completely. Drop a 1' piece of "Sash" chain into the tank and pour in one cup of white vinegar. Swish the vinegar and chain around to knock down the heaviest rust or crud. Drain the tank, and allow to dry in the sun, or use a blow dryer on low to completely evaporate all of the vinegar. Remove the chain and make sure that there is nothing left in the tank like a piece of wick. If there are visible holes in the tank, use masking tape to cover them. Put on a pair of disposable gloves, then use a funnel to carefully pour into the tank enough U.S. Standard POR-15 Gas Tank Sealer or Spar Varnish to coat the entire inside. Rotate the lantern to thoroughly coat both the bottom and sides of the inside of the tank. If you get any on the fuel spout or burner cup be sure to clean it off. After it cures in a few days, another coat can be added if the condition of the tank warrants it. Let the lantern cure for one full week, remove the masking tape and put the lantern back into service. This method of re-sealing will usually last the life of the lantern.

Items marked in this catalog with are made in the U.S.A., or made with components made in the U.S.A.

Adirondack Scenic, Glens Falls, New York Antietam National Battlefield, Sharpsburg, Maryland

Bass Pro Sport Shops, Nationwide Black Bear Jamboree, Pigeon Forge, Tennessee

Buffalo Bill's Casino, State Line, Nevada Burning Man Festival, Black Rock City, Nevada

Busch Gardens, Williamsburg, Virginia California State Railroad Museum, Sacramento, California

Casino Windsor, Windsor, Ontario, Canada Cedar Point Amusement Park, Sandusky, Ohio

Cosi Science Museum, Toledo, Ohio CSX Railroad, U.S.A.

Dayton Museum of Discovery, Dayton, Ohio Department of the Interior, Washington D.C.

Disneyland Resort, Anaheim, California Disneyland, Lantau Island, Hong Kong / Tokyo, Japan / Paris, France

Dolly Partons Dixie Stampede, Branson, Missouri Dolly Partons Dollywood, Pigeon Forge, Tennessee

Double J Resort, Rothbury, Michigan Durango & Silverton Narrow Gauge Railroad, Durango, Colorado

Drake Well Museum, Titusville, Pennsylvania Dry Gulch, U.S.A., Adair, Oklahoma

Farmers Branch Historical Park, Farmers Branch, Texas Fort Davis National Historic Site, Fort Davis, Texas Fort Delaware State Park, Delaware City, Delaware

Fort Laramie National Historic Site, Laramie, Wyoming Fort St. James Historic Site, British Columbia, Canada

Great Smoky Mountains Railroad, Bryson City, North Carolina Great Wolf Lodge, U.S.A. and Canada Locations

Hawthorne Sundae Saloon, Escondido California Knoebels Amusement Resort, Elysburg, Pennsylvania

Knotts Berry Farm, Buena Park, California Legoland, Carlsbad, California

Legoland, Malaysia Legoland, Windsor, United Kingdom Lehman's Hardware, Kidron, Ohio

The Lodge at Red River, Bicknel, Utah Lyndon B. Johnson National Park, Johnson City, Texas Madame Tussauds Wax Museum, Hollywood, California

Melbourne Zoo, Melbourne, Australia NBC-Universal Studios, Burbank, California

Norfolk Southern Railroad, U.S.A. Oceanpark, Hong Kong

Old Town State Historic Park, San Diego, California Paramount Kings Dominion Park, Doswell, Virginia

Railtown 1897 State Historic Park, Jamestown, California Rawhide Western Town, Scottsdale, Arizona

Saddle Ranch Restaurant, Hollywood, California and Kansas City, Kansas Salt Lake 2002 Winter Olympics, Salt Lake City, Utah

Silver Dollar City, Branson, Missouri Six Flags Over Texas, Arlington, Texas

South Dakota's 1880 Town, Murdo, South Dakota Staten Island Historical Society, Staten Island, New York

Stone Mountain Park, Stone Mountain Georgia Strasburg Railroad, Strasburg, Pennsylvania

Twin Peaks Restaurants, U.S.A. Velvet Ice Cream Company, Utica, Ohio

Walt Disney Studios, Burbank, California Walt Disney World, Orlando, Florida

Warner Brothers Studios, Culver City, California Wilderness Grill, Miami Florida

White Pass & Yukon Railroad, Skagway, Alaska Worlds of Fun Amusement Park, Kansas City, Missouri

Documents

Lanternnet.com Catalog