MR16 Lamp

Lamp Module A

FIG 1.4 Lamp at 45° vertical axis position

FIG 1.3 Lamp at 0° vertical axis position

IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS SAVE THESE INSTRUCTIONSWarning-To Reduce the risk of FIRE OR INJURY:Lighted lamp is HOT! Turn off power and allow lamp to cool before replacing lamp. Lamp gets HOT quickly! Do not touch hot lens or enclosure. Keep lamp away from materials that may burn. Do not touch the lamp at any time. Use a soft cloth to remove lamp. Oil from skin may damage lamp. Do not operate the luminaire with a missing or damaged lens. Do not exceed maximum lamp wattage specified on luminaire.

Incandescent Lamp Module Instructions Recessed Housing Model Series 804 & 804S

Note: Secure vertical & horizontal lamp position using Lock Knob & Lock Shaft.

Lamp Module A-Relamping & Adjustment

FIG 1.2 Lens Assembly

FIG 1.1 Replacing lamp

Installing or Changing LampStep 1 Remove Lamp & Lens Ring Subasy from Snoot by rotating Lamp Ring counter clockwise. Remove & discard any protective shipping packaging from Lamp Socket if present.Step 2 Pull Lamp Socket through Snoot then push socket onto lamp terminals - FIG 1.1.Step 3 Secure Lens (up to 3) using Lens Holder Ring - FIG 1.1 & 1.2. AdjustmentStep 1 Loosen Lock Knob/Lock shaft to adjust Lamp Module. Change rotation & lamp aiming angle then lock into position desired - FIG 1.3 & 1.4.

OptionalLenses

Lamp Socket

Snoot

Lamp Ring

Lens

Lens Holder Ring

Lamp-MR16

Lamp Ring

Clear Lens(Standard)

Horizontal Lock ShaftLoosen to adjust horizontal lamp axis

Vertical Lock KnobLoosen to adjust vertical lamp axis

Lens Holder Ring

Gear KnobTo adjust vertical lamp rotation

!

Number Eight Lighting Company • 8lighting.com 11703-Rev 1 • PAGE 1

IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONSWarning-To Reduce the risk of FIRE OR INJURY:Lighted lamp is HOT! Turn off power and allow lamp to cool before replacing lamp or adjusting.Lamp gets HOT quickly! Do not touch hot lens or enclosure. Keep lamp away from materials that may burn.Do not touch the lamp at any time. Use a soft cloth to remove lamp. Oil from skin may damage lamp.Do not operate the luminaire with a missing or damaged lens.Do not exceed maximum lamp wattage specified on luminaire.

Remove / Replace Lamp Module A

RemovalStep 1 Remove Trim Plate & detach from cable clip - Fig 2.1. Step 2 Adjust vertical axis to 0° (lamp aiming perpendicular to mounting surface) - Fig 2.2 Step 3 Remove Lamp Ring/Lens Holder subassembly - Fig 2.3. Step 4 Disconnect Lamp socket and remove Lamp - Fig 2.4.Step 5 Use flat blade screw driver & loosen Bolt while holding Lamp Module from turning - Fig 2.5.Step 6 Orient Lamp Module so it can be pulled through ceiling aperture - Fig 2.6.Replacement: Re-install by replacing all parts in steps above in reverse order.

FIG. 2.1 Remove Trim Plate FIG. 2.2 Adjust Lamp Module to 0° FIG. 2.3 Remove Lens & Lamp RIngs

FIG. 2.4 Disconnect Socket FIG. 2.5 Loosen Bolt FIG. 2.6 Remove Lamp Module

CeilingAperture

Lamp Ring & Lens Holder Ring

Slotted Bolt head

Trim Plate

Lamp Module only(Housing not shown)

Lamp Module

CeilingAperture

CeilingAperture

Socket

Lamp

Number Eight Lighting Company • 8lighting.com 11703-Rev 1 • PAGE 2

B-S Square

MR16 LAMP

B-R Round

H-S Square

H-R Round

FIG 3.2 Wall Wash Lamp Module H-Square & Round

IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONSWarning-To Reduce the risk of FIRE OR INJURY:Lighted lamp is HOT! Turn off power and allow lamp to cool before replacing lamp or adjusting.Lamp gets HOT quickly! Do not touch hot lens or enclosure. Keep lamp away from materials that may burn.Do not touch the lamp at any time. Use a soft cloth to remove lamp. Oil from skin may damage lamp.Do not operate the luminaire with a missing or damaged lens.Do not exceed maximum lamp wattage specified on luminaire.

Lamp Module B & H-Installation, Lamping & Adjustment

Install or Replace LampSTEP 1 Remove Lamp Module from Trim & install or replace Lamp & Lens into Clip. Then push Lampholder into Lamp pins - Fig 3.2.STEP 2 B Lamp Module: Adjust reflector horizontal & vertical aiming angle as needed & secure with Lock Knob into position desired - Fig 3.1. H Lamp Module: Install in Trim oriented so light washes desired wall - Fig 3.2.STEP 3 Secure Safety Cable to Cable Clip. Line up steel Discs in Trim Plate with Magnets in Trim then install Lamp Module into Trim in position desired - Fig 3.1 & 3.2.

FIG 3.1 Mirror Reflector Lamp Module B-Round & Square

Lock Knob(Vertical adjustment 0-90°)

Lock Knob(Horizontal rotation adjustment)

Reflector (shown at 90° position)

4x Steel Disc

LampholderPush onto lamp terminals

Trim Plate(Round)

Trim Plate(Square)

Reflector shownin 0 degree position

Trim(FS-P Shown)

Safety Cable

Cable Clip

MR16/12V Lamp

Clear Lens

MR16/12VSelect beam spread to suitapplication

CAUTION: Always attach Safety Cableto Cable Clip. Be sure cable or clip does not interfere with attaching Lamp Module to Trim.

Lamp Clip

Cable Clip

CAUTION: Always attach Safety Cableto Cable Clip. Be sure cable or clip does not interfere with attaching Lamp Module to Trim.

12V MR16 (40 Deg EXN Flood recommended)

Soft Focus Lens

Spread Lens-rib side faces down

Lamp Clip

Safety Cable

Lens Clip

Spread Lens

LampholderPush onto lamp terminals

Lamp Holder Bracket

Lens rib direction to be perpendicular to wall

Soft Focus Lens

Trim (FR-P Shown)

Clear Lens

4x Magnet

4x Steel Disc

4x Magnet

Number Eight Lighting Company • 8lighting.com 11703-Rev 1 • PAGE 3

QTET

CAUTION: ►Disconnect power at circuit breaker or fuse panel before proceeding.►Always allow Lamp & Power Supply Module to cool before removing. To remove LED Power Supply Modules

Step 1 To access Power Supply Module the Lamp Module must first be removed (For Lamp Modules refer to Pages 1-4).Step 2 Unscrew & remove Thumb Knob inside Housing as shown. Tilt Power Supply Module to disengage offset tab from housing as shown-FIG 4.1.Step 3 Pull Power Supply Module away from threaded stud and pull wires & Power Connectors out of the Junction Box-FIG 4.2. Step 4 Disconnect Power Supply Connectors. For models with 0-10 drivers, also disconnect purple & gray wires-FIG 4.2. Step 5 Pull Power Supply Module through aperture-FIG 4.3.For Replacement: Replace all parts in steps above in reverse order. Push all wires into wiring compartment & replace Power Supply Module as shown in FIG 4.4.

Power Supply Module Removal / Replacement

FIG 4.1 Remove Thumb Knob & Disengage Power Supply Module (Model 804 shown)

FIG 4.2 Remove Power Supply Module & disconnect wires FIG 4.3 Pass Power Supply Module Through Aperture

FIG 4.4 Replace Power Supply Module & Secure With Thumb Knob (Model 804 Housing shown)

Recessed Housing Model Series 804 & 804S

CAUTION: Be sure all wires & connectors are safely pushed inside wiring compartment

before tightening Knob.

!

Disconnect Power Supply Connectors

Thumb KnobPower Supply Module

Threaded Stud

Disengage offset tab& slide out to remove

Offset tab inserts into housing wiring compartment

Thumb Knob (hand tighten securely)

11703-Rev 1 • PAGE 4Number Eight Lighting Company • 8lighting.com