Lab Equipments Electronics

8/10/2019 Lab Equipments Electronics

1/10

SCHEDULE OF SPECIFICATIONSPART 6-LABEQUIPMENTS -ELECTRONICS

(1) DSO 100MHz 1 GS/s Colour Digital Storage Oscilloscope With FFT

FEATURES,1GS/s real time sample rate

7 inch TFT colour display 800x480 resolution

Dual Channel,32 automatic measurements

Saving 10 Waveforms and 10 setup parameters, Convenient USB port interface

Convenient USB port interface

SPECIFICATIONS

Bandwidth: DC - 100MHz

Channels: 2 + External

Display : 7 inch LCD Colour (800X480 resolutions)

Input

Mode: Sample, Peak detect, Averaging

Sample rate(real time): 1GS/s

Input coupling: DC, AC, GND, Noise reject, HF, LF, Reject

Input Impedance : 1Mhom 2% in parallel with 20pF 3pF

Probe attenuation factors: 1X, 10X, 100X, 1000X

Max. Input Voltage : 300 RMS,(1Mohm input impedance)

Horizontal system

Record length : Max.24K points

Time Base Range : 4ns/div ~ 40s/div (step as 2~4~8)

Time Base Accuracy : 100 ppmVertical system

Vertical Resolution : 8 bits

Vertical sensitivity : 2mV/div ~ 10V/div (Input to BNC)

Position Range: > = 10 div

Single bandwidth : Full bandwidth

LF Respond (AC,-3dB) : > = 10Hz (to BNC)

Rising time ( Typical on BNC ) : 3.5 nS

DC Gain Accuracy: 4% (2mV / div)~(5mV / div)

Trigger

Trigger Mode : Edge, Pulse, Video, Slope, Overtime, Alternative

Trigger Slope ( Edge ): Rising, Falling

Trigger Mode ( Edge ) : Auto, Normal and Single

Trigger Sensitivity ( Edge ) : 1 div

Trigger Level Range (Edge)

AC Coupling : CH1 and CH2: 1 div

Internal : 5 divisions from screen center

EXT : 3 V

EXT / 5 : 15 V

Trigger Level Accuracy (Edge)

Internal : 0.2 divisions


2/10

EXT : 40mV 6% setting value

EXT / 5 : 200mV 6% setting value

Trigger mode (Pulse) : < , >, = positive and negative pulse

Pulse width : 20ns-25s

Trigger Sync (Video) : Field, Line

Trigger sensitivity( VIDEO )

Internal : 2 divisions

EXT : 400 mV

Line / Field Frequency: Supports NTSC, PAL

Measurement system

Automatic measurement

Voltage :PK-PK, amplitude, maximum, minimum ,high, low, middle, mean,

averaging, RMS, overshoot, Pre-shoot

Time : Frequency, Cycle, rise time, fall time, positive pulse, negative pulse, positiveduty ratio, negative duty ratio, delay 1->2_UP, and delay1-

>2_DOWN,period,+width,-width, V top, V mid, Vamp, Overshoot, Preshoot, , Period

Mean, Period RMS, FOV Shoot, RPRE Shoot, BWIDTH, FRF, FFR,LPR, LRF, LFR,

LFF

Waveform math : Add, Subtract, Multiply, Divide

Waveform storage: 10 waveform, 10 setups

Lissajou's Figure: Available

FFT Window: Hanning, Hamming, Blackman, Rectangle

FFT Acquisition points : 1024 points

Accessories: At tenuated probe (1X, 10X),USB Cables , manual,(AC code)


3/10

(2)20MHz DDS Funct ion Generator

SPECIFICATION ,A CHANNEL

Frequency characteristics of waveform

Length: 4 ~ 16000 bits

Amplitude resolution : 12bits

Sample rate : 100MSa/S

Frequency range of waveform

Sine wave: 1Hz~20 MHz

Square wave : 1Hz ~ 5MHz

Saw tooth wave: 1mHz ~ 1MHz

Pulse wave: 1mHz ~ 1MHz

Arbitrary wave: 1mHz ~ 1MHzCharacteristics of sine wave

Total harmonic distortion(1Vpp) : DC ~ 100KHz: -60dBc : 100KHz~1MHz: -50dBc : 1MHz~10MHz :-35dBc

Non-harmonic distortion: DC~1MHz: -50dBc

Characteristics of square wave

Rise: About 20ns

Overshoot : About 12%

Duty : 0% ~ 100%

Characteristics of saw tooth wave

Line :


4/10

ASK: Set carrier amplitude and transition amplitude arbitrary

FSK: Set carrier frequency and transition frequency arbitrary

PSK: Transition phase : 0 ~ 360Resolution : 11.25

Sweep characteristics

Carrier: Sine, Square, Saw tooth , Pulse, Arbitrary

Type: Linear or logarithmic

Range: Set starting and end point arbitrary

Time interval: 1ms ~ 60S

Pulse string

Carrier: Sine, Square, Sawtooth , Pulse, Arbitrary

Cycle number : 1 ~ 50000CYC

Initial phase: 0 ~ 360

DC offset

Range : 10V (high impendence) ; resolution : 20mV

Accuracy : (1% +20mV)

Characteristics of sync output

Output amplitude : 5V

Frequency : 1Hz ~ 2MHz

B CHANNEL

Frequency range of the waveform

sine wave: 1Hz ~ 20MHz

Square wave : 1Hz ~ 5MHz

AM modulation

Carrier : Sine, Square, Sawtooth , Pulse, Arbitrary

Type : Internal or external

AM depth: 0% ~ 120%

Modulation frequency : 5Hz ~ 50KHz

FM modulation


Modulation frequency : 5Hz ~ 50KHz

FM deviation : DC ~ 20MHzKeying characteristics

ASK : Set carrier amplitude and transition amplitude arbitrary

FSK : Set carrier frequency and transition frequency arbitrary

PSK : Transition phase : 0 ~ 360; resolution : 11.25

Sweep characteristics


Type : Linear or logarithmic

Sawtooth wave: 1mHz ~ 1MHz

Pulse wave : 1mHz ~ 1MHz


5/10

Arbitrary wave: 1mHz ~ 1MHz

Characteristics of shine wave

Total harmonic distortion (1Vpp)

- DC~ 100KHz :- 60dBc; 100KHz~1MHz :- 50dBc; 1MHz~10MHz :- 35 dB c

-Non-Harmonic distortion : DC~1MHz :- 50dBc

Characteristics of square wave

Rising time: About 20ns

Up rush : About 12%

Duty cycle : 0% ~ 100%

Characteristics of sawtooth wave

Linear:


6/10

(3)Universal Programmer and IC Tester

supports EPROM EEPROM FLASH MPU MCU DSP PAL PIC PLD CPLD FPGA

Microcontroller BPROM SPROM NV RAM and much more.PC running Windows2003,XP ,8,LINAX, connects to USB

(4)XILINX SPARTAN 3E FPGA TRAINER KIT: (VPTB-10)FEATURES :* Xilinx XC3S250E PQ208 Spartan 3E FPGA* 250K gates , 5, 508 Logic cells, 216K Bits of blockram & 12 dedicated multipliers16 Nos. of digital input using slide switches with LED indication* 16Nos. Of digital outputs using discrete LEDs* 16 x 2 LCD is provided for display the text message.* One Reset Switch

* One switch is provided for giving manual clock* FPGA configuration through

# JTAG port# On board Flash Prom XCFO2S

* Free parallel downloading cable* Support for Xilinx Parallel cable IV* Cashew jacket for 5V power supply* Total 158 I/O pins : 124 pins used for integrating peripheral like LED, Switches etc.,

balances pins available to user in 20 pin header (3.3V compatible)* 1No of 26pin header to interface VLIM cards like Traffic Light Controller (5Vcompatible)* On board programmable PLL oscillator from 3 MHz to 100 MHz using jumpers

* 4 Nos of 7 segment LED display*One relay and Buzzer provided.* On board USB to JTA is available for configure FPGA* 4 x4 matrix key provided* Housed in a sleek plastic cabinet with built in SMPS 5V/2A.* Compatible with Xilinx ISE Foundation / Web PACK Software

(5)DSP 320 TMS 320XXXX DSP TrainerThe DSK features the TMS320C6745 DSP, a 375 MHz device delivering up to 3648million instructions per second (MIPs)and 2736 MFLOPS

On board clock generatorWhite noise generatorSignal and noise adderLCD,7 segment displayHigh -quality 24bit stereo CODECRTC interfaceKeyboard SPECIFICATIONSHardwareJTAG supported via USBTLV320AIC23B programmable stereo codecTwo 3.5mm audio jacks for microphone and speakerExpansion port for plug-in modules


7/10

Power supply : +5V, 12V, GND8 DIP switches for inputs and 8 LED indication for outputProvision for manual Reset

4*4 LED matrixWhite noise source of amplitude 0~5Vpp20*2 character LCD display7 segment displaysRTC interface : I2C based RTC sectionPhone keypad : 0 to 9 digits and *, # charactersEXPERIMENTSTo study the architecture of DSP chipsTMS 320c6X instructionsTo verify linear and circular convolutionTo design FIR(LP/HP/BP) filters using windowing techniquea) using rectangular windowb) using triangular window

c) using Kaiser windowTo implement IIR(HP/LP/BP) using following windowa) Chebyshev filterb) Butterworth filterN-point FFT algorithmN-point DFT and IDFT of given sequenceFrequency response of system which is given in transfer function and differential formPower spectrum densityGeneration of sine waveDFT and IFFT using DIT and DIF methodsAuto-correlation, cross-correlation and it's propertySampling of sine signal

Amplitude modulation, frequency modulation and FSK modulationFIR filter using Blackman and hamming windowGeneration of square waveImplementation of decimation, interpolation and I/D sampling rate converterImpulse response of 1st and 2nd order systemAddition and removal of noiseSpectrogram of audio or sine signalGeneration of DTMF signals and spectrogram of DTMF signalRTC displayed on LCDSignal companying using -lawGeneration of sinusoidal wave based on recursive differential equationGeneration of sinusoidal through filtering

To find the FFT of given signalFIR filter using Fourier series expansion methodImage processingDigital image fundamentalsImage enhancementImage filteringImage reconstructionColor image processingImage compressionImage segmentationMorphology image processingAccessories


8/10

DSP 320 development boardPower supply with power cordUSB to JTAG emulator for DSP programming , Microphone and headphone

Patch cordsDVD containing deliverablesExperimental manual

(6)PLC:Different voltages, i. e. 12 V DC, 24 V AC / DC, 115 / 240 V AC / DC Can be used for awide range of applicationsAutomatic changeover for configured daylight saving time Reduces maintenanceoverheadPassword protection Protects your engineering IP38 integrated, pre-tested functions No additional devices, such as elapsed timecounter, are required

Linking of 200 functions is possible Extensive applications can be implemented withoutrestrictionsEight digital inputs (incl. four AIs at 12 / 24 V DC) and four digital outputs on boardDisplay of message texts, action items and current values as well as direct modificationof the values on the display (except for Pure versions)Integrierte Datenremanenz sorgt fr die uneingeschrnkte Sicherung von Aktualwertenbei SpannungsausfallRetentive data memory Protects current values against loss in the event of a powerfailureFlexibly expandable up to 24 DIs, 16 DOs, 8 AIs and 2 AOs, Protects originalinvestment, Suitable for a wide variety of applicationsSoftware LOGO! Soft Comfort V6 for user-friendly generation of control programs on PC;

suitable for a variety ofoperating systems, such as Windows 95/98, NT 4.0, Me, 2000,XP, Vista, MAC OS X 10.4 with J2SE 1.5.0 and SUSE LINUX 10

(7)Digital IC TrainerDC Supply : +/- 5V/1A, +/-12 V /500 mASocket : 2 nos,20PIN ZIF SocketBread Board: 2n0s.1280 tie pointsLogic I/P : 10 nos Toggle Switches and LEDsLogic O/P : 10 nos Bright LEDs

TTL Clock : 1 Hz,10Hz,100Hz,10KHz,1MHzDisplay : 4 nos 7 Segment DisplayMono pulse : 1 Hi and 1 Low pulseTerminals : 2 mm Spring Terminals


9/10

(8)Lab VIEW for ARM Microcon tro llers Teaching Ki t -includes CORTEX M3 hardwareB2SPICE EDATool and software Support mixed mode simulator

Support partly Berkeley spice simulator and partly Georgia spice simulatorGuaranteed industrial strength accuracySupport large part database from standard venders like Analog Devices, Bur Brown,Comlinear, Motorola, National semiconductors, Texas instrument, AMP, Maxim, LinearTechnology and many moreSupports creation of parameterized sub circuit modelAllows any open circuit to be converted as a partAdvanced toolbar designed to quickly select parts, control simulations and set virtualinstruments requiredSupport test and simulation mode. Simulation allows constant time domain simulationand test allows predefined analysis that is run on the circuit to check its behaviorAllows 12 powerful tests

Supports animation such as graphical and text representation of resultsCircuit wizards supports easy circuit creationSupport virtual instruments- Oscilloscope, Ammeter, Voltmeter, and many moreAllows porting of designs between third party applicationDatabase editor allows to import models and parts into the database and also to modifyand add symbols, change categories and manufactures etc.SIMULATION ILLUSTRATIONSTest modeTransient testApplication of DC biasPerforming DC sensitivity testUse of DC transfer function setup

Application of AC sweepDistortion verificationNoise analysis experimentGeneration of device and model parametersNetwork analysisSimulation modeAnalog circuit simulationDigital circuit simulation - Simple circuit simulation- Time and frequency analysisExperiment to create parameterized sub circuit model to generate new part withsimulation model to generate new part with simulation modelComprehensive experimental support as per the university syllabus coverage AND,NOR, GatesMOS inverter, NMOS inverter, CMOS inverter

Differential amplifier FET and MOSFET amplifiers BJT inverter CE, CS, RC coupled,Cascade amplifier, Current shunt, Voltage series feedback amplifierClass A, Class B complimentary, symmetry power amplifier, Source follower, Emitterfollower, Darlington pair amplifier, Audio amplifier, Log-Antilog amplifiersPhase shift, Hartley, Colpitts and Crystal oscillator Wein bridge oscillator using op-amp,Multivibrators using op-amp,Zero crossing detector using op-ampVoltage regulators, Active filtersFunction generator using op-amp (sine, triangular and square wave)Voltage regulatorsImplementation and simulation of given logic function using dynamic logic simulation ofadders ( half, full )Simulation of subractor ( half, full )


10/10

Binary counter

(9)Dual Power supply

0- +/-30V/3A,5V fixedOutput voltage=0- +/-30V &5V fixedinput voltage=230v 50HzLine regulation=0.01%+/-5%Load regulation=0.01%+/-5%ripple 1mV vrms

(10)Digital Millimeter,Digital LCD Multimeter Voltmeter Ammeter OhmmeterDigital LCD Multimeter with auto power off and auto zero functionDH button for maintaining dataSingle 32 position switch for function and range

Voltage measurements of the Voltmeter: AC 750V and DC 1000V maxCurrent measurements of the Ammeter: DC 10A max and AC 10AResistance measurements of the Ohmmeter: 200MohmLED and Transistor measurement functionDiode and transistor (HFE) testCapacitance measurements: 200uFLarge LCD screen display and shake resistantDurable soft plastic cover protectionDC voltage scale: 200m/2/20/200/1000VBasic accuracy: /- 0.5% ( /- 0.25% for 200mV range)AC voltage: 750VBasic accuracy: /- 1.2%

Frequency range: 45-450HzDC current scale: 2m/20m/200m/10ABasic accuracy: /-1.0% ( /-2.0% for 20A range)Overload protection: 200mA 250V fuse (20A-range is not fuse-protected)Resistance scale: 200/2k/20k/200k/2M/20M/200MBasic accuracy: /- 0.8%Overload protection: 220Vrms max for 15 secondsOver range: yes, Transistor test: yesDiode test: yeslow-battery indication: yesLCD display size: 6.2 x 3.1cmMeter Size: 19 x 9 x 3.2cm (L*W*D)

Power supply: NEDA 1604 or 6F22 9V battery (not include)1 X LCD Digital Voltmeter Ohmmeter Ammeter OHM Multimeter2 x Test lead- Warranty: 1 Month Vendor warranty against manufacturing defects

(11)Logic ProbeMax. Input Signal Frequency: 20 MHz, Input Impedance: 1M,Operating Supply range:4V DCmin18V DC Max., TTL : Logic "1" (Hi LED) >2.3

Documents

Lab Equipments Electronics