KroSAT Vulcano Manual Do Usuario English v130116

SAFETY PRECAUTIONS1. INTRODUCTION

1.1 About This Manual1.2 General Description1.3 Main Features

2. HARDWARE DESCRIPTION2.1 Front Panel Configuration2.2 Rear Panel Configuration2.3 Remote Control unit

2.3.1 Appearance of romte controller2.3.2 Instruction to keystoke of romte controller

3. SYSTEM OVERVIEW3.1 Working Modes3.2 Main Menu Structure

3.2.1 Installation Menu3.2.2 Channel Menu3.2.3 Setting Menu3.2.4 Game Menu3.2.5 Multimedia Menu

3.3 Multimedia3.3.1 Filter Selection Mode3.3.2 Movie3.3.3 Music3.3.4 Photo3.3.5 Native32 Game3.3.6 Recorder Manager3.3.7 Disk Manager

4. BASIC FUNCTION 4.1 Enter into System and Power on-off

4.1.1 Enter into DVB system

Contents11

5688888

14

15161818

19192022

23232425262627

1

4.1.2 Power on4.1.3 Power off

4.2 First Installation4.3 Volume Adjustment and Mute4.4 TV/RADIO Programs Switch4.5 Station Switch4.6 Speediness Program List4.7 Display information of Programs4.8 Program Return4.9 Audio Language Switch and L/R Channel Switch4.10 Electronic Programs Guide (EPG) 4.11 Teletext4.12 Subtitle4.13 REC & Time shift

5. INSTALLATION5.1 Antenna Setting 5.2 Satellite List 5.3 Transponder List5.4 Motor Setting

5.4.1 DiSEqC 1.25.4.2 Usals

5.5 Limit Setup

6. CHANNEL6.1 Channel Manager6.2 Favorite List

7. PREFERENCE SETTING7.1 OSD Language7.2 Preferred Subtitle7.3 Hard Hearing7.4 Preferred Audio7.5 Multimedia

2931323637383940

41424242434446

4848505152545458595960616667

2

7.6 PVR Config

8. SYSTEM SETTING8.1 Timers8.2 Child Lock8.3 Date Time8.4 Active Antenna8.5 Factory Reset8.6 Upgrade8.7 Version8.8 Auto Standby

9. AV SETTING9.1 Contrast9.2 Brightness9.3 SPDIF 9.4 Aspect Ratio9.5 Video Output9.6 Video Resolution

10. GAME10.1 Box Man10.2 Tetris10.3 Hit Rat10.4 Go Bang10.5 Sudoku

11. SOFTWARE UPGRADE12. TROUBLE SHOOTING 11. TECHNICAL SPECIFICATIONS

68686868686868

686868 68 68 68

68 68

3

4

SAFETY PRECAUTIONSPlease read the following safety precautions carefully before handling the STB.

POWER REQUIRED

North American models - Use only 100 -120V AC 60Hz.Europe / Middle East models - Use 90 - 240V AC 50 / 60Hz

CABLE Use standard certified cables to prevent any malfunction of the STB.

LOCATIONLocate the STB indoors. Locate STB away from potential hazards such as excessive moisture. STB should not be subjected to direct sunlight, excessive heat or power surges.

CLEANING

1. Always disconnect the STB power cord from the wall socket before cleaning it.2. Use a lightly dampened cloth to clean the exterior of the STB. (Use no solvents.)

OVERLOADING Do not overload wall outlets, extension cords or adapters. This can cause a fire or electrical shock.

VENTILATION

1. NEVER block ventilation slots of the receiver.2. NEVER stand the STB on soft furnishings or carpets.3. Ensure that a free airflow is maintained around the STB.4. Do not use or store the STB where it is exposed to directsunlight or near a heater.5. NEVER stack other electronic equipment on top of the STB.

LIQUIDS Keep liquids away from the STB.

SMALLOBJECTS

Coins or other small objects must be kept away from the STB. They can fall through ventilation slots of the STB and cause serious dam-age.

ATTACHMENTS Do not use any attachments that are not recommended. These may cause hazards or damage the equipment.

LIGHTNING

The STB must remain connected at all times to the main power supply. However, Manufacturer’s instructions for safeguarding other equipment connected to the STB, TV set, etc., should be followed during lightning storms.

SERVICING 1. Do not attempt to service this product yourself.2. Refer all servicing to qualified service representatives.

5

1. INTRODUCTION

1.1. About This ManualThis manual describes how to setup and operate your STB. Only qualified person-nel should handle any problems beyond this manual.

1.2. General DescriptionThe STB is a high-performance digital satellite receiver, which is fully compliant with MPEG2 and MPEG4, based on DVB transmission standards for in-home re-ception of digital satellite services such as digital television and radio channels.

1.3. Main FEATURES- Full 1080p- Easy to opearate HD Menu System- Ethernet port- Media Player- USB PVR Ready- Youtube- Google Map- Weather on-line- Picassa- Game and more- Receives Hign Definiteion channel- Support 32 timers- Favorite channel groups TV and Radio- QuickFind Function- Support Teletext and Subtitle- DiSEqC 1.0, 1.1 and USALS support- MPEG-2, MPEG-4, MPEG-4 AVC/H.264 Support- Fully compliant with DVB-S and DVB-S2

6

2. HARDWARE DESCRIPTION

2.1. Front Panel Configration

F1: STANDBY/ONAfter connecting the mains power, press this button to switch ON the receiver or to switch to STANDBY

F2: DIGIT LED DISPLAYThis will display the current channel or certain programming functions when using the menus.

F3: REMOTE CONTROL SENSORLocation of the infrared receiver. Ensure that this is not obstructed when using the remote control.

F4: OKThis button is used in conjunction with the setup or menu functions when entering to change the programming parameters.

F5: CH (Up)In program mode this button will move the cursor (highlighted) upwards to facilitate selection. In normal operation mode it is used to step up channels sequentially.

F5

F2

F6

F9

F7F4

F3

F8F1 [ Figure 2.1. Front Panel ]

7

F6: CH (Down)In program mode this button will move the cursor (highlighted) downwards to facilitate selection. In normal operation mode it is used to step down channels sequentially.F7: VOL (Up)In program mode this button will move the cursor (highlighted) to the right to facili-tate selection. In normal operation mode it will increase the sound volume.

F8: VOL (Down)In program mode this button will move the cursor (highlighted) to the left to facili-tate selection. In normal operation mode it will decrease the sound volume.

F9: SMART CARD INTERFACE (Option)To watch scrambled channels, you should insert a smart card, which has been issued by the service provider, into the Smart Card Interface slot. You can watch only a specific range of channels with entitlements in the smart card. The smart card includes information to decipher parameters necessary for descrambling the program

8

2.2 Rear Panel Configration

CONNECTORS AND DEFINITIONS

Please do not connect the power to the receiver until all other connections have been made and checked. Please refer to diagram above for connec-tions.

R1: LNB IN ( IF Input )Connect the IF cable from your LNB on your dish to this connector.

R2: LOOP OUTIf you have a second satellite receiver, connect the receivers LNB input to this connector.

R3: Coaxial R4: VIDEOComposite video output for connecting to an AV monitor etc.

R5: AUDIO LEFT / RIGHTStereo audio output socket for the televisionset or the audio system. (white/red)

R2 R9R6R4

R8R5R1 R3 R7

[ Figure 2.2. Rear Panel ]

9

R6: LANConnect your LAN cable for the network connection.

R7: USBConnects to the USB memory.

R8: PowerTo switch AC Power on/offI cable to this connector

R9: ON-OFF To switch Power on/off

2.3 Remote Control Unit

2.3.1 Instruction to keystoke of romte controller1. [POWER] Switch of power supply

2. [MUTE] Mute control

3. [EXIT] Programs replaying under mode of full screen

4. [MENU] Enter main menu

10

[ Figure 2.3. Remote controaller ]

11

5. [VOL+/-] Volume adjusting

6. [INFO] Display corresponding Extended information at EPG state

7. [TEXT] Teletext

8. [SUBTITLE] Subtitle

9. [F.R & F.F](1) Iamge zoom in/out(2) Speed up/down while USB Media playing

10. [STOP] Stop playing USB Media

11. [CH+/-] Left/right channel

12. [ZOOM](1) Enable/disable zoom;(2) Switch to Daily Mode(epg page)(3) Set/unset program locked in channel manager menu

13. [NUMBER] Digital strokes

14. [TV/RADIO] TV/RADIO switch

15. [AUDIO] Audio pid switch and left/right channel

16. [UP / DOWN/LEFT/RIGHT & OK] Move high_light and confirm

17. [EPG] Go to EPG

18. [PLAY] Play USB Media

19. [PREV/NEXT] Play previous/next USB Media

20. [PAUSE] Pause key

21. [SLOW] Slower movie playing speed while playing USB movie

22. [REC] Enter REC

23. [PAGE+/-] Page up/down

28. [BACK](1) Return to upper menu

(2) Press “BACK” under state of full-screen to return to the previous program palyed.

29. [GOTO] Enter goto menu

30. [REPEAT] Set repeat mode

31. [ENTER/FAV] Enter channel/Fav list

34. [DEV] Device List

3. System overview3.1 Working Modes

There are two modes in our system: DTV Mode and Multimedia Mode. We can play digital TV programmers in DTV Mode and play multimedia (include NES and Native32 games) in Multimedia Mode. Since power on, the system will enter DTV mode directly. We can switch between DTV andMultimedia mode by pressing [SOURCE] Key.

3.2 Main menu structureSystem main menu structure is like figure 3.1:

12

[ Figure 3.1 Main menu structure ]

DTV Mode

Multimedia Mode

Installation

Channel

Preference

Setting

AV

Game

Main Menu

3.2.1 Installation Menu

3.2.2 Channel Menu

13

Anterna Setting

Satellite Setting

Transponder List

Motor Setting

Limit Setup

Installation

[ Figure 3.2 Installation Menu ]

Channel Manager

Favorite List

Favorite List

Channel

[ Figure 3.3 Channel Menu ]

3.2.3 Setting Menu

14

[ Figure 3.4 Setting Menu ]

Hard Hearing

Bgmusic

Timeshift

1st Preferred Subtitle

Music Repeat

File Size

OSD Language

Movie Repeat

MPEG2 File Format

1st Preferred Audio

Slide Time

Timeshift Length


Photo Repeat

Preferred Storage

2nd Preferred Audio

Effect

Timeshift to Record

Mutimedia

PVR Config

Preference

Aspect Ratio

Brightness

Contrast

Video Output

SPDF

Video Resolution

HDMI Deep Color

HDMI Color Space

AV

Date Time Date Time Mode

Timers Parental Rating

OTA Upgrade

System Lock

USB Upgrade

Common Interface Time Zone

Child Lock Change Pin Code

RD Ugrade

Factory Reset

Upgrade

Version

Setting

3.2.4 Game Menu

3.2.5 Multimedia Menu

15

[ Figure 3.6 Multimedia Menu ]

Hard Hearing


OSD Language

1st Preferred Audio


2nd Preferred Audio

Mutimedia

PVR Config

Preference

[ Figure 3.5 Game Menu ]

Box Man

Tetris

Hit Rat

Go Bang

Sudoku

Game

3.3 Multi-Media

KroSAT Vlucano integrates powerful function to support USB and you can con-nect Ex-equipments via the USB. At present, system can support usual USB me-dia players and upgrade to system software.This product supports the play of MP3, JPEG and MPEG. It can support only the files displaying in the list and the file format this product plays.

3.3.1 FILTER SELECTION MODEThis menu helps the user to change the filter mode from movie to music or from music to photo and so on.For example the current filter selection is photo, following menu layout 9.1 shows the “filter selection” menu.

There are three keys are used in this menu, following table 9.1 shows the keys, and other keys do not mentioned in the table shall be ignored.

Key Stroke ActionKEY_DOWN Change from filter selection mode to file list.

KEY_LEFT Change filter selection mode, for instance from movie to music, from music to photo etc.

KEY_RIGHT The same as KEY_LEFT.

The following table 9.2 shows every filter selection mode and its corresponding icon.

16

[ Table 3.1 : Multimedia - “filter selection” menu – Navigation Table ]

[ Figure 3.1 Multimedia - “filter selection” menu ]

17

Icon Filter selection mode

Filter selection mode is “Movie” mode

Filter selection mode is “Music” mode

Filter selection mode is “Photo” mode

Filter selection mode is “Native32 Game” mode

Filter selection mode is “Recorder Manager” mode

Filter selection mode is “Disk Manager” mode

Filter selection mode is “E-book” mode

3.3.2 MOVIE1. Movie file browserThis menu helps the user to select and play a movie from a list of movies that are stored in the USB device.Supported file formats are MPG, AVI, VOB, DAT, ASF, MKV, RM, WMV, TSF, QT.Following menu layout shows the “Movie” menu.

[ Table 3.2 Multimedia – Filter Selection Mode ]Icons

[ Figure 3.2 Multimedia - “Movie” menu ]

Key Stroke Action

KEY_UP Shall highlight the previous Item in file list. If Control reaches first item, it shall highlight the last item in file list.

KEY_DOWN Shall highlight the next Item in the file list. If Control reaches last item, it shall highlight the first item.

KEY_PAGEUPThis key can works in file list only, It shall highlight the same Item of last page, If item is not exist in last page, it shall high-light the first item.

KEY_PAGEDOWNThe same as KEY_PAGEUP, it only can work in file list too. But it shall highlight the same Item of next page in file list, If item is not exist in next page, it shall highlight the last item.

KEY_LEFT If the current file has its parent folder, press this key will returnfrom current list to parent folder.

KEY_RIGHT If current highlight item is a folder, it can enter to the folder.

KEY_ENTERIf current highlight item is a folder, press KEY_ENTER shall enter into the folder. Else if it is a file then press the key will play the selected video.

KEY_RECALLIf current highlight is in file list, press KEY_RECALL shall return to the filter selection mode. Else if it is playing video now, press the key shall return to layout 9.2

KEY_NUM

The input number is shown at the area of text “loading”, the highlight shall change to the corresponding item according to the input number. If the input number is larger than the number of file list, incorrect message will be popped.

KEY_MENU File browser menu disappear and show main menu or main menu disappear and show file browser again.

KEY_SOURCE Shall change the source to DVB.

18

[ Table 3.3 Multimedia - “Movie” menu – Navigation Table ]

2. Movie playback

The keys handled in this menu are shown in table 2.3.2.2. Keys don’t mentioned in this table are ignored. All the settings shall be saved as on when they are changed.

Key Stroke ActionKEY_ZOOM Shall zoom in/out the image

KEY_PREV Shall stop this movie and play the previous movie in the list.

KEY_NEXT Shall stop this movie and play the next movie in the list.

KEY_PLAY If the movie is pause, FF, FB, SF or SB, it will change to playmovie at once and show play icon.

KEY_PAUSE If the movie is playing, then this will pause and show pause icon

KEY_STOP Shall stop the movie and show the layout 9.3

KEY_FF 2x → 4x → 8x → 20x → 1x, and the playback mode shall be diplayed on the upper left corner.

KEY_FRShall fast reverse the movie. It can cycle through the sequence 2x → 4x → 8x → 20x → 1x, and the playback mode shall be displayed on the upper left corner.

KEY_SLOW Shall slowly play the movie.

KEY_RECALL The same as the key KEY_STOP

19

[ Figure 3.3 Multimedia - “Movie playback information” menu ]

KEY_MUTE TV mute shall be toggled.

KEY_VOLUME Shall change the volume

KEY_INFO Shall display information of the playing movie provided by Sun-plus Driver as “Movie” menu 9.3

KEY_GOTO Go to menu will be showed when press this key

KEY_P-SCAN Book Mark menu will be showed when press this key

When the video is playing, the following information provided by the Sunplus driver shall be displayed on OSD:

a. File name.b. Total time and the current time for this playing file.c. Play state of this video.d. Progress bar.e. File size and resolution of this video.f. Repeat mode such as off/one/dir.

The information icons shown while video playing are shown as in Table 9.5

Icon Description

Shall zoom in/out the image

Shall stop this movie and play the previous movie in the list

Shall stop this movie and play the next movie in the list.

Play vedio

Pause Video

Stop Video

Fast Reverse, it shall be replace with 1x, 2x, 4x, 8x, 20x.

Fast Forward, it shall be replace with 1x, 2x, 4x, 8x, 20x.

Slowly play

Fast play.

20

[ Table 3.4: Multimedia - “Movie playback” – Navigation Table ]

[ Table 3.5 : Multimedia – “Movie playback”– Information Icons ]

3) Go to menuThe keys handled in this menu are shown in table 9.6. Keys don’t mentioned in this table are ignored.

Key Stroke ActionKEY_UP Switch between Time edit mode and time move control mode

KEY_DOWN The same as KEY_UP.

KEY_LEFT In time edit mode to move highlight curser or in move control mode to move mark.


KEY_ENTER Move the playing movie to the selected time.

KEY_RECALL Quit the go to menu.

KEY_GOTO Exit from the go to menu.

21

[ Table 3.6 : Multimedia – “Go to menu”– Navigation Table ]

[ Figure 3.4: Multimedia - “Go to menu” menu ]

4) Book Mark menuThe keys handled in this menu are shown in table 9.7. Keys don’t mentioned in this table are ignored.

Key Stroke ActionKEY_LEFT Switch book mark in six marks.


KEY_ENTERSelect the current playing time as a bookmark. If the boomark is selected press this key shall move the play time to the selected time.

KEY_RECALL Quit the book mark menu.

KEY_P-SCAN The same as KEY_RECALL

22

[ Figure 3.5 Multimedia - “Book Mark menu” menu ]

[ Table 3.7 : Multimedia – “Book Mark menu”– Navigation Table ]

3.3.3 MUSICThis menu helps the user to select and play a song from a list of songs that are stored in the storage device. WMA, WAV, DTS, RA and MP3 format will be sup-ported for playing.Following layout shows the “Music” menu.

The following are some explanations for above “Music” menu

1. File list as we think is the list of folder and music.2. On the left of file list shows the information of folders and files, for example filter selection is in music mode, it shows EQ, the progress, play state, total time and file size etc information of the playing music.3. The hint of above menu is help information to notice the use what keys can be used in current time.4. The music is background music, so when music is playing, user can changedirectory or change filter list to other mode such as movie, photo, e-book and so on.

The keys handled in this menu are shown in table9.8. Keys not mentioned in this table are ignored.

23

[ Figure 3.6: Multimedia - “Music” menu ]

Key Stroke Action



KEY_PAGEUPThis key can works in file list only, It shall highlight the same Item of last page, If item is not exist in last page, it shall highlight the first item.

KEY_PAGEDOWNThe same as KEY_PAGEUP, it only can work in file list too. But it shall highlight the same Item of next page in file list, If item is not existed in next page, it shall highlight the last item.

KEY_LEFT If the highlight is in the file list and it has parent folder, shall return from current list to parent folder.

KEY_RIGHT If the highlight is in the file list and current highlight item is a folder, it can enter to the folder.

KEY_RECALLIf current highlight is in file list, press KEY_RECALL shall return from file list to the filter selection mode. At present if the file is music and it is playing, KEY_RECALL shall stop it.

KEY_PREVIf current highlight is on music and the music is not in stop status, press this key shall stop this one and to play the previous music, but the highlight don’t move.

KEY_NEXTIf current highlight is on music and the music is not in stop status, press this key shall stop this one and to play the next music, but the highlight don’t move.

KEY_PLAY

If the music is pause, FF, FB, SF, SB or stop, it will change to play music at once and show play icon. At same time, the music icon before the name of the playing music will change to game icon, the area of “file size” shall disappear and shows current playing music’s name.

KEY_PAUSE If the music is playing, then press the key will pause and show pause icon.

KEY_STOP Shall stop the music and show stop icon, the area of “file size” shall show file size again.

KEY_FF Shall fast forward the music. At this time FF icon is shown and sequence such as 1x 2x, 4x, 8x, 20x shall display too.

KEY_FR Shall fast reverse the music. At this time FR icon is shown and sequence such as 1x 2x, 4x, 8x, 20x shall display too.

25

KEY_NUM

The input number is shown at the area of text “loading”, the high-light shall change to the corresponding item according to the in-put number. If the input number is larger than the number of file list, incorrect message will be popped.


KEY_SOURCE Shall change the source to DVB

When the music file is playing, the following information provided by the Sun-plus driver shall be displayed on OSD:

g. EQ informationh. Total time for this playing file.i. Play state of this music.j. Progress bar.k. Current number of this file in total file list.l. File size, artist, album and genre.

The play state icons in table 9.9 are shown while play music

Icon Description

Shall stop this music and play the previous music in the list

Shall stop this music and play the next music in the list.

Play

Pause

Stop

Fast Reverse

Fast Forward

26

[ Table 3.8 : Multimedia – keys handle in “Music” menu ]

[ Table 3.9: Multimedia – “Music” Play state icons ]

3.3.4 PHOTO1. Photo file browserThis menu contains the Photos that are stored in the storage device. Supported file formats are JPG, TIF, PNG, GIF and BMP.Following menu layout shows the “Photo” menu.

The keys handled in this menu are shown in table 9.10. Keys not mentioned in this table are ignored.

Key Stroke Action

KEY_UP Shall highlight the previous Item in file list. If Control reachesfirst item, it shall highlight the last item in file list.

KEY_DOWN Shall highlight the next Item in the file list. If Control reacheslast item, it shall highlight the first item.

KEY_PAGEUPThis key can works in file list only, It shall highlight the sameItem of last page, If item is not exist in last page, it shallhighlight the first item.

KEY_PAGEDOWNThe same as KEY_PAGEUP, it only can work in file list too.But it shall highlight the same Item of next page in file list, Ifitem does not exist in next page, it shall highlight the last item.

KEY_LEFT If the highlight is in the file list, press the key shall return fromcurrent list to parent folder.

27

[ Figure 3.7 Multimedia – “Photo” Menu ]

KEY_RIGHT If the highlight is in the file list and current highlight item is afolder, it can enter to the folder.

KEY_ENTERIf current highlight item is a folder, press KEY_ENTER shallenter into the folder. Else if it is a file then press the key willplay the selected photo.

KEY_RECALL If current highlight is in file list, press KEY_RECALL shall return from file list to filter selection mode.

KEY_NUM




KEY_YELLOW Shall show thumbnail menu.

2. Photo playbackThe “Photo Playback” Menu which shown in following layout shows the play-back menu while photo is playing. Layout 9.8 shows the playback menu for play photo commonly and Layout 9.9 shows the setup menu for slide show.

28

[ Figure 3.8: Multimedia – “Photo playback” menu for photo play commonly ]

[ Table 3.10: Multimedia – “Photo” Menu – Navigation Table ]

When a image is displayed in full screen then the following keys are handled:

Key Stroke ActionKEY_UP Shall rotate the image 180

KEY_DOWN Shall rotate the image 180

KEY_LEFT Shall rotate the image 270

KEY_RIGHT Shall rotate thr image 90

KEY_PREV Displays the previous image in the List. If the displayed image is the first one then the key is ignored.

KEY_NEXT Displays the next image in the List. If the displayed image is thelast one then the key is ignored.

KEY_INFO Shall display the information of the image provided by SunplusDriver as shown in Layout 9.8 /9.9

KEY_PAUSE Slide show was paused if press the key

KEY_PLAY Slide show was start to play if press the keyShall stop play photo and return to the “Photo” menu

KEY_RECALL Shall Quit the image displayed and return to the “Photo” menuas show in Layout 9.8

KEY_ZOOM Shall zoom in/out the image.

29

[ Figure 3.8: Multimedia – “Photo playback” menu for photo play commonly ]

[ Figure 3.9: Multimedia – “Photo playback” menu for slide show ]

[ Table 3.11: Multimedia – “Photo playback” – Navigation Table ]

The information of play state icons while photo playing are shown as in Table 9.12

Icon Description

Zoom-in to a photo x4

Shall stop this photo and play the next photo in the list.

Play photo

Pause photo

Shall return to file list

3. Photo thumbnailThis menu displays the thumbnail view of the photos stored in the selected folder.

Following menu layout shows the Thumbnail menu.

30

[ Figure 3.9: Multimedia – “Photo Thumbnail” Menu ]

[ Table 3.12: Multimedia – “Photo” while display – Information Icons ]


Key Stroke Action

KEY_UPShall highlight the previous item in the same column. If Control reaches top item in the column, it shall highlight the bottom item in the same column.

KEY_DOWNShall highlight the next Item in the column. If Control reaches bottom item in the column, it shall highlight the top item in the same column.

KEY_PAGEUPShall highlight the same Item of last page in the column, If item is not exist in last page, it shall highlight the first item in the col-umn

KEY_PAGEDOWNShall highlight the same Item of next page in the column, If item is not exist in next page, it shall highlight the last item in the column

KEY_LEFTShall highlight the previous item in the row. If Control reaches first item in the row, it shall highlight the last item in the same row.

KEY_RIGHT Shall highlight the next item in the row. If Control reaches last item in the row, it shall highlight the first item in the same row.

KEY_ENTERIf current selected item is a folder, press KEY_ENTER shall enter into the folder. else if the selected file (photo) shall be displayed in full-screen mode.

KEY_RECALL Shall show the “Photo” menu as in Layout 9.8

KEY_SOURCE Shall change the source to DVB.

KEY_RED Shall show the “edit” menu.

KEY_GREEN Shall show with “slide show” mode.

KEY_NUM


31

[ Table 3.13: Multimedia - “Photo Thumbnail” Menu – Navigation Table ]

3.3.5 NATIVE32 GAMEThis menu contains the games that are stored in the storage device. Supported file formats are native32 and NES.Following menu layout shows the “Native32 game” menu.


Key Stroke Action





KEY_LEFT If the highlight is in the file list, it shall return from current list to parent folder.


32

[ Figure 3.10: Multimedia – “Native32 game” Menu ]

33

KEY_ENTERIf current highlight item is a folder, press KEY_ENTER shall enter into the folder. Else if it is a file then press the key will play the selected game.

KEY_RECALL If current highlight is in file list, press KEY_RECALL shall return from file list to the filter selection mode.

KEY_NUM


KEY_MENU File browser menu disappears and shows main menu or main menu disappears and shows file browser again.

KEY_RED Change the type of game from native32 to NES

KEY_SOURCE TShall change the source to DVB

3.3.6 RECORDER MANAGER1. Recorder manager browserThe following menu9.12 shows recorder manager menu that the recorded TV programs stored in storage device.


[ Figure 3.11: Multimedia – “Recorder manager” Menu ]

[ Table 3.14:Multimedia – “Native32 game” Menu – Navigation Table ]

34

Key Stroke Action





KEY_LEFT If the highlight is in the file list, it shall return from current list to parent folder.


KEY_ENTERIf current highlight item is a folder, press KEY_ENTER shall enter into the folder. Else if it is a file then press the key will play the selected recorded program

KEY_RECALL

If current highlight is in file list, press KEY_RECALL shall re-turn from file list to the filter selection mode. Else if it is playing recorded program now, press the key shall return to “Recorder manager” Menu.

KEY_RED If it is root directory, press this key shall set partition. If it is sub directory press it will delete the selected item

KEY_GREEN If it is root directory, press this key shall format the card to FAT32, If it is sub directory press it will rename the selected item.

KEY_YELLOW If it is root directory, press this key shall format the card to NTFS, If it is sub directory press it will show move and copy menu.

KEY_NUM




[ Table 3.15: Multimedia – “Recorder manager” Menu – Navigation Table ]

35

2. RenameThe following menu 9.13 is rename menu. In this menu the user can change the program’s name as them like.


Key Stroke Action

KEY_UPShall highlight the previous Item in the same column. If Control reaches first item, it shall highlight the last item in the same col-umn.

KEY_DOWN Shall highlight the next Item in the same column. If Control reaches last item, it shall highlight the first item in the same column.

KEY_LEFT Shall highlight the next Item in the same row. If Control reaches last item, it shall highlight the first item in the same row.

KEY_RIGHT Shall highlight the last Item in the same row. If Control reaches first item, it shall highlight the last item in the same row.


KEY_RED Change the character between capital and lowercase

KEY_GREEN Make a blank in the name

KEY_YELLOW Delete the current character of program name that cursor on

KEY_BLUE Confirm the modification of the name and the menu return to “Re-corder manager” Menu.

[ Figure 3.12: Multimedia – “Rename” Menu ]

[ Table 3.16: Multimedia – “Rename” Menu – Navigation Table ]

36

3.3.7 DISK MANAGER1. Disk manager browserThe menu of disk manager is like file browser menu, the keys work likes in file browser menu. But the function of four color keys is different. Following table shows the function of four color keys, other keys are same with the keys in other file browser menus.

Key Stroke ActionKEY_RED Show move/copy menu

KEY_GREEN Show rename menu

KEY_YELLOW Delete the selected item

2. RenameThe menu is same with Layout 9.13: Multimedia – “Rename” Menu, and i ts keys is same with table 9.16 too.

3. Move/CopyThe following menu9.14 is Move/copy menu. In this menu the user can move file or folder from one side to other side. It also can copy the content at one side to other side. At present, user can move/copy each other between two sides.

[ Figure 4.13: Multimedia – “Move/copy” Menu ]

[ Table 3.17: Multimedia – “disk manager browser” Menu – Navigation Table ]


Key Stroke Action

KEY_UP Shall highlight the previous Item in file list. If Control reachesfirst item, it shall highlight the last item in file list.

KEY_DOWN Shall highlight the next Item in the file list. If Control reacheslast item, it shall highlight the first item.

KEY_PAGEUP It shall highlight the same Item of last page, If item is not existin last page, it shall highlight the first item.

KEY_PAGEDOWNLike the KEY_PAGEUP, But it shall highlight the same Item ofnext page in file list, If item is not exist in next page, it shallhighlight the last item.

KEY_LEFT Change the highlight from one side to other side.


KEY_ENTER IIf current highlight item is a folder, press KEY_ENTER shallenter into the folder.

KEY_RECALL Return to parent folder.

KEY_EXIT Return to disk manager menu.

KEY_GREEN ISelect the highlight item and highlight move to other side.

KEY_YELLOW Copy the content of select item to other side

KEY_BLUE Move the select item to other side

KEY_MENU File browser menu disappear and show main menu or mainmenu disappear and show file browser again.


3.3.8 E-Book1. E-Book browserThe menu of e-book is like file browser menu, the keys work likes in file brows-er menu. But the four color keys have no function. Other keys are same with the keys in other file browser menus. For instance, KEY_UP/KEY_DOWN can move highlight and KEY_ENTER to play selected e-book etc.

37

[ Table 3.18: Multimedia – “Move/Copy” Menu – Navigation Table ]

2. E-Book menuThe following menu 9.15 is E-Book menu. In this menu the user can read text file, the menu shall, except the content of current file, also show the name of current file and total pages and current page number.


Key Stroke ActionKEY_PAGEUP Move to previous page, if it is already the first page, it will don’t move.

KEY_PAGEDOWN Move to next page, if it is already the last page, it will don’t move.

KEY_PREV The same as KEY_PAGEUP

KEY_NEXT The same as KEY_PAGEDOWN

KEY_NUM User can input number key to select page as they want.

KEY_ENTER If user input number key to select page number, then press this key will go to corresponding page.

KEY_RECALL Return to file browser menu of e-book.

KEY_EXIT The same as KEY_RRECALL

KEY_MENU E-book menu disappear and show main menu or main menu disappear and show e-book again.


38

[ Figure 3.14: Multimedia - “E-Book” menu ]

[ Table 3.19: Multimedia – “E-Book” Menu – Navigation Table ]

39

4. Basic functions4.1 Enter into system and power on-off

Please check up whether it is good connection with power, whether the voltage is stable, hether the antennae is connected, and whether there is any physical damage to the circuit board.

4.1.1 Enter into DVB system

It will enter DVB mode as soon as system power on. Figure 2.1 shows the system interface while none TV/RADIO programs in the database:

It will continue to play the latest program before previous power off if the database having and TV or RADIO program.(if failed to enter into the mode, please check above operations and ensure the romter works well)

4.1.2 Power onWhen it is in “standby” mode, press “power” to power on.

4.1.3 Power offWhen it is running, press “power” will enter into “standby” mode.

[ Figure 4.1: DVB screen (without program) ]

40

4.2 First InstallationFirst installation shall setup some important configures. It contains several options shown as figures:

User can select OSD Language, Time Zone, Single Satellite Search and Multi Satellite Search from this menu, when it is set completely, User can use “Start

Search”to search channels.

4.3 Volume adjustment and Mute1. Press “vol+/-” to adjust volume when system is in normal playing mode; and it will show volume bar on the image.2. Press “MUTE” to enter into the mode when normally playing and repress “MUTE” to back the normal state.

4.4 TV/RADIO programs switchPress “TV/RADIO” to switch the programs when it is in full screen.

4.5 Station switch1. Press “CH+/-” to switch to the previous or next program.2. Press number keys to input program number.

[ Figure4.2: Init menu ]

4.6 Speediness program list

1. Press “ENTER” to switch to the speediness program list, press “LEFT/RIGHT” to select different program class; press “UP/DOWN” to select program.

Press “ENTER” to affirm program selection, press “EXIT” return to hide menu

41

[ Figure 4.3: speediness program list ]

2. Press “red” key to enter the satellite list. as shown in Figure 2.10, and then press “enter” key will show all TV of the focused satellite.

If there are some favorite programs that been set up, just press “GREEN” key to enter into the favorite program list:

42

[ Figure 4.4 ]

43

Press “UP/DOWN” to select favorite program, Press “ENTER” affirm the selection, press “RETURN” to return to hide menu.Press “Yellow” key and you can find the TV as you want, as shown in figure.

[ Figure 4.5: favorite program list ]

44

Press “Blue” key enter program type list, as shown in figure ,you can filter free or scramble program as you want.

[ Figure 4.6 ]

[ Figure 4.7 ]

4.7 Display information of programsPress key “DISPLAY” to show the information of current programs when it is in normal palying state.

4.8 Program returnPress “RETURN” under state of full-screen to return to the previous program palyed.

45

[ Figure 4.8: program information display ]

4.9 Audio language switch and L/R channel switch1. Press “AUDIO” key to switch the language of sound of current programs and switch among “stereo” → “left” → “right”(stereo → left channel → right channel).

2. Press “LEFT/RIGHT” to switch among “stereo” → “left” → “right”(stereo → left channel → right channel), press “UP/DOWN” to switch the language of sound.

3. Press “ENTER” key confirm the selection and return to full-screen play mode, press “EXIT” to return to full-screen play mode and save the setting.

46

[ Figure 4.9: audio language and L/R switch list ]

4.10 Electronic programs guide (EPG)1. You can press key “EPG” on the remote controller to enter into the EPG page to know more about the programs to be played. As shown in the figure below:

Enter into EPG menu default enter Now/Next Mode, menu under this mode contain 7parts, As shown in the figure above:

(1) Tab 1 shows the Title ;(2) Tab 2 shows time and date list;(3) Tab 3 shows particular date list;(4) Tab 4 shows program list, press “UP/DOWN” to switch between programs;(5) Tab 5 shows the time range and program information, press “F.R & F.F” circularly to hoose to browse the time range and program information on basis of days of every week;(6) Tab 6 shows the detailed program information in Tab 5;(7) Tab 7 shows hint information for keys, corresponding to the two colors on the remote controller: ZOOM,N/P;(8) Press “LEFT/RIGHT” to switch between NOW and NEXT;

47

[ Figure 4.10: EPG menu ]

2. Press “Zoom” key to enter into Daily/Weekly Mode to display the programs and program information in different time ranges of the currenty program list within one week, as shown in Figure 2.10:

(1) Press TIMER & M/F key to switch between Sunday ---Saturday in Tab 3;(2) Press UP/DOWN key to move upward and downward to switch between the different programs in Tab 5;(3) Press LEFT/RIGHT key to choose to view the program information in different time ranges in Tab 6.

48

[ Figure 4.11: Weekly Mode ]

3. When the cursor stops on Tab 5 in Figure 2.9, press the INFO key to choose the detailed information corresponding to the current program, as shown in Figure 2.11:

4. When the cursor stops on Tab 5 in Figure 2.9,, press the green N/P key to set Timer to book programs, as shown in Figure 2.12:

5. Press “EXIT” to exit from EPG.

49

[ Figure 4.12: Extended Mode ]

[ Figure 4.13: EPG Timer Edit ]

4.11 Teletext1. If you want to watch teletext, please press “TEXT” on the romte controller to enter into EPG page. As shown in the figure below:

2. Input three digits to go to corresponding page you want;4. Press “UP” to go to the previous page, while press “DOWN” to go to the next page;5. Press “Enter” to adjust the transparence:6. Press “TEXT” or “EXIT” to exit from teletext.7. If the country selected UK, There should display MHEG-5 instead of teletext when “TEXT” key has been pressed.

50

[ Figure 4.14: Teletext page ]

4.12 Subtitle1. Subtitle is defaulted to be off; to see the capitation information, press the SUBTITLE key on the remote controller to enter the Subtitle menu of the current programs, as shown in Figure 2.14:

2. Press UP/DOWN key move upward and downward to choose language.

4.13 RECAt playback screen press “REC” key to start record, system will has 3 seconds for initialization. As shown in the figure below:

51

[ Figure 4.16: REC Initializing ]

[ Figure 4.15: Subtitle menu ]

When initialization success, the screen lift top will show “REC” icon, recording and playing current program. You can press “info” key to watch current record-ing information.

Press “stop” key while recording, will stop record and resume normal playback mode.

In the recording, you also can use REC key to set timer for subscribe stop record, besides you can reset the time optionally.(can set the time length as cancel(00:00),or user define length)

52

[ Figure 4.17: REC Info. ]

[ Figure 4.18: REC stop ]

when the space is insufficient while recording, system will show prompt mes-sage then stop recording and resume normal play back mode.In the recording, if a write failure happened is by reason of storage bad track problems, system will show prompt message and try again.In the recording, you also can operation Menu, EPG, TTX, Subtitle and so on function like normal play back mode.

53

[ Figure 4.19: REC duration ]

5. InstallationThere are five items as follow:

1. Antenna Setting2. Satellite List3. Transponder List4. Motor Setting5. Limit Setup

You can enter into “installation page” via inputting password (default password is “0000”), As shown in the figure below:

54

[ Figure 5.1: Installation Main Menu ]

5.1 Antenna SettingOn the installation menu, press [UP/DOWN] to select the item [Antenna Setting] and then log into via [ENTER] as shown in the Picture 4.2.

1. Satellite: Choose a satellite from the database and set up the following parameters.2. LNB Type:

C Band → Set the satellite to the C frequency band;Universal → Set the satellite to the KU frequency band;User → Set up the local oscillation frequency of LNB by users.

3. LNB Frequency: Select the local oscillation frequency.4. Transponder: This is a satellite frequency which is used to display the signal quality, facilitating to adjust relevant parameters.5. 22K: set 22K tone signal to ON or OFF.6. 0/12Volt: set output to 0 or 12 Volt.7. LNB Power: set Power supply to ON or OFF for LNB use.8. DiSEqC Mode: Select the version of DiSEqC, include DiSEqC1.0/1.1.

When configuration is done, press [ENTER] to call out a dialogue box (Do you want to save?) YES Save; NO → Quit without saving. Press [RETURN] to quit to the previous menu.

55

[ Figure 5.2: Antenna Setting Interface ]

5.2 Satellite List

This [Satellite List] menu(Figure 4.3) list all satellites stored in system. You can do ADD, EDIT, DELETE and SCAN action with Color Key on your IR. For example, we can edit a satellite by pressing green key, then the popup menu will show the options you can modify(Figure 4.4).

56

[ Figure5.3: Satellite list ]

[ Figure 5.4: Edit satellite ]

5.3 Transponder ListYou can move the cursor to “Transponder List” via press “UP/DOWN” key under “Installation”, then press “enter” to enter into manual search page, As shown in the figure below:

Transponder List saved all the transponder in selected satellite,and every tran-sponder maybe have some channel. Then press the 4-color key on the remote controller: press the red key to set and cancel Add Transponder, the green key to set or cancel Edit Transponder, the yellow key to set or cancel Delete Tran-sponder, the blue key to set or cancel Scan Transponder.

57

[ Figure 5.5: Transponder List ]

When press the green key to set or cancel Edit Transponder,you can edit the requency,symbol rate and polarization of the transponder. Press “OK” to com-plete.

5.4 Motor SettingUnder the page, press [LEFT/RIGHT] to select the option [Motor Setting] and then you can select DiSEqC 1.2 or Usals Function as shown in the picture 4.7.

58

[ Figure 5.7: Motor Setting ]

[ Figure 5.6: Edit Transponder ]

59

5.4.1 DiSEqC 1.2

Satellite: Select a satellite;Transponder: Select a frequency point;Move Step: Press [LEFT] once and MOTOR rotates to the east by one step; Press [RIGHT] and MOTOR rotates to the west by one step;Continuing Move: Stop → Pause; Move east → Rotate in the eastbound way; Move west → Rotate in the westbound way;Go to: Move the polar axis holder to a corresponding location by entering numbers in PositionPosition: Identigy the polar axis holder’s location stored by User or default.Save: Save Current LocationReset: Reset the polar axis holder;

[ Figure 5.8: DiSEqC 1.2 ]

60

5.4.2 Usals

My Longitude: Set up the longitude of the current locationMy Latitude: Set up the altitude of the current location.

[ Figure 5.9: Usals ]

5.5 Limit Setup

Limit Setup: Set up the extreme coordinate; Disable Limits → No extreme coordinate; Set East Limit → Set up the eastbound extreme coordinate; Set West Limi → Set up the estbound extreme coordinate;Continuing move: Stop → Pause; Move east → Rotate in the eastbound way; Move west → Rotate in the westbound way;Move Setp: Press [LEFT] once and MOTOR rotates to the east by one step; Press [RIGHT] and MOTOR rotates to the west by one step.

61

[ Figure 5.10: Limit Setup ]

6. Channel System offer an efficient function of channel management such as channel delet-ing, marking, moving, locking, rename and grouping.,There are two independent pages for channel management, TV and RADIO, as shown in the figure below

6.1 Channel ManagerChannel manager page includes channel deleting, moving, locking and rename.

1. You can enter the page as shown in the figure below via “MENU → channel → Channel Manager”

62

[ Figure 6.1: Channel Menu ]

2. it will pop up and dialogue box prompting that “Channel not available” when there are nochannels in database to enter into, and it will not enter into channel organizer page.

1) Channel Organizer menu includes: Delete Channel, Skip Channel, Lock Channeland channel rename. Press UP/DOWN key to choose the line where Chan-nel is, then press the 4-color key on the remote controller: press the red key to set and cancel lock Channel, the green key to set or cancel Delete Channel, the yellow key to set or cancel Skip Channel, the blue key to set or cancel rename Channel; After setting, corresponding figure will appear;

63

[ Figure 6.2: Channel manager page ]

[ Figure 6.3: Channel manager edit page ]

2) To rename channel , press UP/DOWN key to choose the line where the channel to be renamed , press the blue M/F key to enter the page to rename the channel, as shown in Figure 4.4:

3) Press the blue key to exit Channel rename page.4) To set or cancel Lock Program, the system will hint to input “0000”; to set Delete Program, the system will hint to choose dialogue box“Delete selected Channels?”, Press LEFT/RIGHT key to choose, choose “Yes” to delete the program chosen, “No”to cancel;5) Press EXIT key to exit Channel manager page and saving the edit result.6) After channel is edited, when EXIT key is pressed to exit the menu, if actual channel editing action exists, the system will carry out Favorite list renewal, with the hint of “Data Saving…”.

64

[ Figure 6.4: Edit Channel-Name Page ]

65

6.2 Favorite List1. You can enter the page As shown in the figure below via “Main menu → channel → Favorite list:

2. It will pop up and dialogue box prompting that “Channel not available” when there are no programs in database to enter into, and it will not enter into channel grouping page.

3. Press UP/DOWN key to choose the line where the channel to be grouped is in, then press the colour keys on the remote controller to set different channel grouping.

[ Figure 6.5: Favorite list page ]

66

7. Preference SettingConfiguration provides individualized preference setting function, you can configure the system according to your own hobby and demand. as shown in Figure 5.1:

7.1 OSD LanguageOSD Language option: The system has the user interface supporting a couple of languages, you can set language via OSD Language option:

1) Move the cursor onto OSD Language option , Press RIGHT key to enter OSD Language List as shown in Figure 5.2:2) Press UP/DOWN key choose language;3) Press ENTER key to confirm system interface language selection, then the setting is effective, and then the interface language turns into the currently chosen language, the cursor can move onto OSD Language option on the left;

[ Figure 7.1: Preference setting page ]

7.2 Preferred Subtitle1) Sets the preferred subtitle to “English”, “French”, “German”, “Italian”, “Spanish”, “Portuguese”, “Danish”, “Czech”, “Dutch”, “Finnish”, “Swedish”, “Greek”, “Russian”, “Welsh”, “Gaelic”, “Hungarian”.

2) When the preferred subtitle be select, it will display the selected subtitle automatically while the stream has the suited subtitle.3) User can set another preferred subtitle in the “2nd Preferred subtitle”.

67

[ Figure 7.2: OSD Language page ]

[ Figure 7.3: Preferred subtitle page ]

7.3 Hard HearingEnables/Disables the “hearing impaired”Hard Hearing is a special service for someone who’s hard of hearing. It is a special kind of subtitle which contains the description of the voice of invisible environment, such as the lightning.If it is set to On, you may press Subtitle Key to select it

When you set the hard hearing on and play a media contains Hard Hearing subtile, it will be shown as below:

68

7.4 Preferred Audio1. Sets the preferred audio to “English”, “French”, “German”, “Italian”, “Spanish”, “Portuguese”, “Danish”, “Czech”, ”Dutch”, “Finnish”, “Swedish”, “Greek”, ”Russian”, ”Welsh”, ”Gaelic”, “Hungarian”.

2. 1st preferred audio option: Press RIGHT key to enter the currently supported Audio Language list, in the Audio Language list, press UP/DOWN key to choose language, press OK key to confirm;

3. 2nd preferred audio option: Press RIGHT key to enter the currently supported Audio Language list, in the Audio Language list, press UP/DOWN key to choose language, press OK key to confirm;

7.5 MultimediaIt used in Media source, you can configure the seeting according to your own hobby and demand. as shown in Figure 5.5:

69

[ Figure 7.4: Preferred audio page ]

7.6 PVR ConfigYou can enter the page as shown in the figure below via “MENU → Preference → PVR Config”, it contains six options as fallow;* MPEG2 File Format* File Size* Preferred Storage* Timeshift* Timeshift Length* Timeshift to Record

70

[ Figure 7.5: Multimedia setting page ]

[ Figure 7.6: PVR Config setting page ]

1. MPEG2 File Format:Either of options, TS/PS, can be selected to set the format of the file to be stored; if TS mode is selected, related psi/si table information in code stream can be recorded during the record of the programme, or if PS mode is selected, AV data are recorded only.

2. File Size:Any of options, 4G/3G/2G/1G, can be selected to set the size of the file to be recorded; if the size of the file exceeds the setting size during the record of the programme, record program will divide the file into plurality of files with the set sizes.

3. Preferred Storage:Any of options, CARD/USB1/USB2, can be selected to determine USB equipment for stor-age of the file to be recorded.

71

8. System Setting

System Setup menu can provide convenient system setup, as shown in Figure 6.1:

8.1 TimersIf you want to set channel playing at certain time or REC some programs, You can set via Timers menu, as shown in Figure 6.2:

72

[ Figure 8.1: System Setting menu ]

[ Figure 8.2: Timer list menu ]

* Application shall provide list of timer for adding, viewing, editing and deletion.* “Timer” shall list all the timer that are added through the “EPG” as well as the imer that are manually added by the user through the “Timer” menu.* Application supports a maximum of 10 “Timer”.

In Timer Edit menu, the system can support at most 10 events.Date: Specifies the timer dateProgram Name: Specifies the channel for which the timer is setStart time: Specifies the start time of the timerEnd time: Specifies the end time of the timer, be used in Recorder TypeDuration: Specifies the duration time of the timer, be used in Recorder TypeMode: Specifies the frequency of the timer. Duration can be any of the following;

* Once -timer will be triggered only once.* Daily -timer will be triggered daily at the specified time.* Weekly -timer will be triggered every week at the specified time.* Monthly- timer will be triggered every Monthly at the specified time.

Type: Specifies the channel type for which the timer is set,User can select chan-nel, VCR,on and off in this option.If user select recorder type, it can be set En-ables or Disables in zhe follow options such as AD Record.

73

[ Figure 8.3: Timer Edit menu ]

Press OK key the system will return previous menu. as shown in Figure 6.4:

8.2 Child LockChild Lock menu can provide convenient locked setup, as shown in Figure 6.5:

74

[ Figure 8.5: child lock menu ]

[ Figure 8.4: Timer set complete menu ]

1. Here you can set Enables or Disables the system lock, and also can set the parental rating from 0 to 18.

2. You can revise system Password, as shown in Figure 6.6:

1) Press the 0 - 9 number key on the remote controller to input Old Password, the system defaults Password as“0 0 0 0”.2) If the password is input correctly, the cursor can move onto Input New Password option, press 0 - 9 number key on the remote controller to input new 4-digit Password.

75

[ Figure 8.6: Change Password ]

8.3 Date TimeClock Menu contains different clock settings. Following menu layout shows the Time Settings.

If the “Time Mode” is set to “Auto” then, “Time Zone” and “DST” shall be active for editing. If the Mode is “Manual”, these options shall be disabled.If the “Time Mode” is set to “Manual” then, “Date” and “Time” shall be active for editing. If the Mode is “Auto”, these options shall be disabled.

8.4 Active AntennaEnables/Disables the “Active Antenna”

8.5 Auto Search In StandbyEnables/Disables the “Auto Search In Standby”

76

[ Figure 8.7: time setting ]

8.7 Factory ResetThere will be Reset to default when this option be selected. The system will hint to input “0000”; to set factory Reset

8.8 UpgradeRefer to SOFTWARE UPGRADE Section for details. It shows at part 10

77

[ Figure 8.8: factory Reset ]

8.9 VersionVia menu ( MENU->setting-> Version), enter the page as shown in Figure 6.12:

You can be provided with system software information, including H/W Version, S/W Version, F/W Version, Build Date and Time, Press BACK key to return previous menu.

8.10 Auto StandbyEnables/Disables the “Auto Standby”

78

[ Figure 8.9: version ]

9. AV SettingTV setup provides convenient TV input mode, as shown in Figure 7.1:

9.1 ContrastYou can set system contrast via Contrast option.1. Move the cursor to Contrast option, press RIGHT key to move the cursor into the Properties list, press LEFT/RIGHT adjust the contrast, as shown in Figure 7.2:

79

[ Figure 9.1: TV setting menu ]

[ Figure 9.2: contrast ]

2. Contrast can be set from 0 to 24:3. Default:12;

9.2 BrightnessThe same as contrast

9.3 SPDIFUsed to select AVC mode – Mute, PCM and Bitstream

9.4 Aspect RatioVideo output mode can change the mode of video ouput, you can adjust TV mode accordin to the actual situation of you receiving equipment.

1) Move the cursor to Aspect Ratio option, press ENTER/RIGHT to pop up the options, Then press UP/DOWN key to move circularly and choose options;2) Aspect Ratio can be set as 16:9, 4:3 PanScan, 4:3 LetterBox, 16:9 PanScan;3) Press ENTER key to save the setting;

80

[ Figure 9.3: Aspect Ratio ]

9.5 Video OutputVideo Output mode can change the mode of video output, you can ad-just TV mode according to the actual situation of you receiving equip-ment.

1) Move the cursor to Aspect Ratio option, press OK/RIGHT to pop up the options, Then press UP/DOWN key to move circularly and choose options;2) Video Output mode can be set as RGB, YUV, S-Video;3) Default: YUV;4) Press OL key to save the setting;

81

[ Figure 9.4 ]

9.6 Video ResolutionVideo Resolution mode can change the Resolution of video output, you can adjust TV mode according to the actual situation of you receiving equipment.

1) Move the cursor to Aspect Ratio option, press OK/RIGHT to pop up the options; Then press UP/DOWN key to move circularly and choose options;2) Video Output mode can be set as

576i_25, 720p-60, 720p_50, 1080i_30, 1080i_25, 1080p_60, 1080p_50, 480p_60, 480i_30, 576p_50;

3) Default: 576i_25;4) Press OK key to save the setting;

82

[ Figure 9.5 ]

10. Game

If you want to have a rest or to relieve youself after hard working, you can play some gamesattached in the system.

10.1 Box ManPlay: press “MENU” under normal playing mode and select GAME → NativeGames->BoxMan step to play the game.

1. There are six function selection menus on the left of the interface for user: New Game: Restart game, Reset: reset map, Continue: Continue game, Level: Display game level, Help: offer help information, Exit Game: exit game;2. In New Game option, press OK key to enter Game, the function menu on the left, if turning into grey, cannot be used;3. press direction keys up, down, left and right to move the cartoon man here and there.4. Press OK key Pause Game, you can reset game on the function menu on the left of the interface

83

[ Figure 10.1: BoxMan ]

10.2 TetrisPlay: press “Menu” under normal playing mode and select GAME → Native Games->Tetris step by step to play the game.

1. There are five function selection menu on the left of the interface for user: Start Game: Start Game, Setting: set game speed and difficulty, as shown in Figure 6.3:

Help: provide game information, Score List: score list, Exit Game: exit the game.

84

[ Figure 10.3: Setting page ]

[ Figure 10.2: Interface of Tetris Game ]

2. After game-setting, move cursor to “start game” parameter, press “OK” key enter into the game :

3. press key left and right to move the square left or right;4. press key up to change the direction;5. press key down to accelerate the square;6. Press OK key to pause game, Continue Game via the left function key, Main Menu returns to the previous menu, reset Game or exit Game.

85

[ Figure 10.4: start game interface ]

10.3 Hit RatPlay: press “menu” under normal playing mode and select GAME → NativeGames vHit Rat step by step to play the game.

1. There are five function selection menu on the left of the interface for user: New Game: Restart Game;Speed: Set Game Speed, Press LEFT/RIGHT key to set;Score List: score list;Help: help information;Exit Game: exit the game;2. After game-setting, move the cursor to “New Game” parameters, press “OK” key enter into the game :

86

[ Figure 10.5: Hit Rat ]

[ Figure 10.6 ]

3. the direction keys compose 1, 2, 3, 4, 5, 6, 7, 8, 9 vs top left, top mid, top right, mid left, mid right, down left, down mid, down right.4. Press “OK” to pause the game.

Left button “Continue” to continue the game.图 9-1 Left button “Main Menu” return to the previous menu and reset games.

10.4 Go BangPlay: press “menu” under normal playing mode and select GAME → NativeGames → Go Bang step by step to play the game.

1. There are six function selection menus on the left of the interface for user: CHOICE: Choose chessman color for user (default setting is white chessman), LEVEL: Set game level, START: Restart game, UNDO: Quit game in every step, REDO: Drop back into game, EXIT: Exit game;2. After game-setting, move the cursor to “START” parameters, press “OK” key enter into the game:3. Press direction keys up, down, left and right to move the cursor here and there.4. Press OK key to infill chessman.5. Press BACK key to switch cursor to the button zone and choose direction key to switch among some buttons. Press “OK” key to execute button function.

87

[ Figure 10.7 ]

10.5 SudokuPlay: press “menu” under normal playing mode and select GAME → NativeGames → Sudoku step by step to play the game.

1. There are three function selection menus on the left of the interface for user: RESET: Clear all the selected numbers, NEW: Restart Game, EXIT: Exit the game;2. Press direction keys up, down, left and right to move the cursor here and there.3. Press number key “1-9” to infill number, choose “0” clear selected number.4. Press “BACK” key to switch cursor to the button zone and choose direction key to switch among some buttons. Press “OK” key to execute button function.

88

[ Figure 10.8 ]

11. Software Upgrade

You can automatically update the software of the equipment.The software of the new version can support more areas and more functions or solve more problems. Via menu (menu → setting → upgrade) enter Software Upgrade menu, as shown in Figure 10.1:

11.1 USB UpgradeUSB upgrade is a fast and convenient way to upgrade, You simply copy the upgrade file into the USB disk, and push the USB device into the system USB interface, then you can upgrade by the following step as below:

* Before usb upgrade, you must prepare upgrade file, file name usually is “.bin(not case sensitive) , Otherwise the system can not enter the upgrade mode;* The size of USB upgrade file must be less than or equal to 4M bytes, if not may lead to failure to upgrade;* USB upgrade flow:

− Insert contain upgrade file u-disk, press(menu → setting → upgrade → usb upgrade) enter USB directory list page, as show in the figure below:

89

[ Figure 11.1: Software Upgrade menu ]

− Select upgrade file and press “OK” key to start upgrade, enter upgrade page show information to prompt user upgrade progress;

* The whole process of USB upgrade maybe need 30 second;* Please make sure don’t shut down the power in upgrade process;* When upgrade finish, system will automatic restart with the new fireware;

90

[ Figure 11.3: USB upgrade process page ]

[ Figure 11.2: USB upgrade page ]

91

12. TROUBLE SHOOTING

Problem Possible causes What to do

The display on the front panel does not light up. Main cable is not connected. Check that the main cable is

plugged into the power socket.

No sound or picture.

Wrong connection of the video / audio output to the TV input terminal.

Connect RCA or RF cable.

Wrong connection of satellite antenna cable.

Connect the antenna cable correctly.

Wrong direction of satellite antenna. Adjust the direction of antenna.

Adjust the direction of antenna.

Black-and-White screen or VHold problem.

No signal or weak signal.

Check the cable connections LNB and other equipment connected between the LNB and the receiver or adjust the antenna.

Wrong setting of channel in-formation in System Installa-tion Menu.

Type the setting value correctly.

Your TV mode is different from satellite broadcasting mode.

Use TV of same mode. Use a NTSC/PAL converter connected to the receiver TV.

The RCU is not working.

Battery exhausted. Change the batteries.

Fluorescent light interfering with the remote controller. Switch off the light.

RCU is incorrectly aimed. Aim the RCU at the receiver.

92

13. TECHNICAL SPECIFICATIONS

IF / Tuner 1. Input Frequency 950 MHz to 2150 MHz

2. Input Signal Level -25 to -65dBm

3. Input Impedance 75 ohm nominal

4. Input Connector F-type, IEC 109-24, Female

5. FEC Decoder l/2, 2/3, 3/4, 5/6, 6/7, 7/8 for DVB-Sl/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10 for DVB-S2

6. Demodulation QPSK/8PSK

7. Symbol rate Up to 45Msps(37Msps for DVB-S2)/ SCPC, MCP

8. 22KHz Tone Frequency :22KHz±20%, Amplitude :0.6Vp-p±0.2Vp-p

9. LNB Power & Polarization V13 / H18, 600mA MAX. over current protection

Audio / Video Decoding

1. Video Decoder MPEG2 MP@ML,MPEG2 MP@HL,MPEG4 AVC/H.264 HP@L4

2. Input Rate 108Mbit/s Max

3. Video Resolution 720×576p,1280×720p,1920×1080i, 1920x1080p

4. Audio Decoder MPEG-1 Layer 1&2,MPEG-4 Audio

6. Audio Mode Mono L/R, Joint Stereo, Stereo

7. Audio Sampling Fre-quency

32, 44.1, 48 KHz

Audio / Video Output1. RCA Jack Audio L/R, CVBS, Coaxial

USB connection1. USB 2.0 Support USB single connection

Adopter1. Supply Voltage DC 12V

2. Power Consumption 30W Max.

General1. Weight & Dimensions Approx. 24 Kg & 260(W) x 45(H) x 180(D)mm

87

Documents

KroSAT Vulcano Manual Do Usuario English v130116