Konika Installation UnpackC350

7/31/2019 Konika Installation UnpackC350

1/12

E-1

C350

4036-7762-02

INSTALLATION MANUAL

Applied Machine: C350KONICA MINOLTABUSINESS TECHNOLOGIES, INC.

I.Outline of Installation Procedures for 4036 System

When installing the machine and associated options as a system, follow the order shown on the upper.

Caution:

For the detailed installation procedures for each option, follow the instructions given in the corresponding

Installation Manual and perform the procedures correctly.

Electron System Options

PC-101 PC-201 DK-501

DF-601

AD-501

JS-601

FS-501

WT-501

FS-601

OC-501

PK-501/PK-4/

PK-131

Copier/Printer Machine

HD-501

EM-301

PC-401

Dehumidifier Heater 1C

EK-501 VI-501

D-103DT-105

Electron System Options


2/12

E-2

II. Accessory parts

* Varies depending on the applicable marketing area

III.Removing the Machine

1. Open the shipping carton and remove the IU car-

ton and machine carton.

2. Pull out the handles.

3. Work with a helper. Holding onto the portions

shown in the illustration, remove the machine

while maintaining a level position.

No. Name Qty

1. Imaging unit (IU): Y,M,C,BK 4

2. Power cord 1

3. Cord clamp * 1

4. Users guide holder 1

5. Users guide 1

6. Installation manual (this manual) 1

7. Drawer label 1

8. Cap A (round-head) 2

9. Cap B (square-head) 2

10. Connector cover 1

11. Drawer cover 1

12. Mounting screw 2

13. Power cord instruction * 1


3/12

E-3

IV.Removing Protective Tape, Packing and

Other Shipping Materials

1. Remove protective tape from different parts of the

machine.

2. Remove the packing bracket.

3. Remove the protective sheet.

4. Slide out the 1st drawer and remove protective

tape and packing materials from the inside of the

drawer.

5. Slide out the 2nd drawer and remove protective

tape from the inside of the drawer.


4/12

E-4

V.Installing the IU

1. Open the front door.

2. Pinch the IU release lever for Y and pull it down

forward.

3. Tilt the IU to the left and, in that condition, shake

it over a small stroke twice. Then, tilt the IU to the

right and, in that condition, shake it over a smallstroke twice.

Caution:

When holding the IU, be sure to hold onto the blue

label portion.

4. Keeping the IU in the level position, insert it all

the way as far as it will go.

Caution:

When inserting the IU, make sure that the leading

edge of the IU is aligned with the mounting posi-

tion label indicated on the machine.

Make sure that the IU is inserted all the way into

the machine.

5. Holding the IU (indicated by the arrow in the illus-

tration), pull out the PC Drum protective sheet.

6. Push the IU release lever all the way until a click

is heard.

7. Using the same procedure, install all IUs.


5/12

E-5

VI.Charging Toner and Installing the Filter

Caution:

Toner does not come with the machine. Purchase

toner bottles (of different colors) separately avail-

able.

1. Open the front door.

2. Remove the desiccant. (only the black toner bot-

tle)

3. Holding the toner bottle firmly, shake it well verti-

cally and horizontally to agitate toner.

4. Remove the protective tape and the protective

cap.

5. Swing the fixing lever downward.

6. Load the toner bottle in position.

(Make sure that the gear is on the rear side.)

7. Swing the fixing lever upward to fix the toner bot-

tle in position.

* Make sure that the fixing lever is positively swung

into position.

8. Using the same procedure, install the toner bot-

tles for other colors of toner.

9. Take out the filter and install it in position.

Caution:

The filter is packed in the box of a black toner bot-

tle.


6/12

E-6

VII.Connecting the Power Cord and

Mounting the Accessories

1. Connect the power cord.

2. Remove the screw shown in the illustration.

3. Fit the cord clamp furnished with the machine

over the power cord. Then, secure the cord

clamp using the screw that has just been

removed.

Caution:

This step may not be performed depending on the

applicable marketing area.

4. Plug the power cord into the power outlet.

5. Attach the cap A and B enclosed with the

machine.

6. Attach the connector cover enclosed with the

machine.

VIII.Installing the Users Guide Holder

1. Install the users guide holder.


7/12

E-7

IX.Adjusting Touch Panel

1. Turn on the Power Switch.

2. Call Touch Panel Adjust to the screen. (See the

service manual for how to show the function.)

3. Using a ballpoint or similar device, lightly touch

the center of the + markers at four places on the

Touch Panel in order.

(Any specific marker can be the first one.)4. Touch END.

X.Loading the Test Copy Paper1. Load the 1st drawer with A3 or Ledger paper.

2. Place the media types selection dial in the Plain

position.

XI.Setting Gradation Adjust

1. Check that A3 or Ledger paper is loaded in the

drawer.

2. Display the Tech. Rep. Mode screen.

(For details of how to display the Tech. Rep.

Mode screen, see the service manual.)

3. Select Gradation Adjust.

4. Press the start key. A test pattern will then be pro-

duced on the A3 or Ledger paper.

5. Place the test pattern face down on the original

glass.

6. Place about ten sheets of A3 or Ledger paper on

the test pattern placed on the original glass.

Lower the original cover, if the machine is so

equipped.

7. Press the start key. The machine will start reading

the test pattern.


8/12

E-8

8. When the machine completes reading the test

pattern, the Gradation Adjust screen will reap-

pear.

9. Repeat steps from 4 through 7 to let the machine

read the test pattern three times.

10.Touch END.

11.Touch Fin. Time.

XII.Test Copy

1. Check that A3 or Ledger paper is loaded in the

drawer.

2. Ready a test chart.

3. Place the test chart face down on the original

glass.

4. Lower the original cover, if the machine is so

equipped.

5. Press the start key.

6. Check the halftone band portion of the test copy

produced for possible streaks or lines.

If they are apparent, take the necessary remedial

steps by following the troubleshooting procedure

contained in the service manual.

Halftone Band Portion


9/12

E-9

XIII.Date/Time Input

1. Select the Data & Time Setting function as fol-

lows: Utility Admin. Mode Admin. Set. 3/4

Data & Time Setting.

2. Select the item you want to set and press the

clear key.

3. Enter the data for the year, month, day, and time-of-day from the 10-key pad.

4. Touch Enter.

5. Touch Fin. Time three times.

6. Display the Date/Time Input screen.

(For details of how to display the Date/Time Input

screen, see the service manual.)

7. Press the clear key.

8. Enter the data for the year, month, day, and time-

of-day from the 10-key pad.9. Touch Entry.

10.Touch END.

XIV.Serial # Input




2. Select the Serial # Input function as follows:

System Input Serial # Input.

3. Making sure that Printer is selected on thescreen, enter the serial number of the printer from

the 10-key pad.

4. Following the same procedure, enter the serial

numbers of all other units.

5. Touch END.

6. Touch Fin. Time.

7. Turn OFF/ON the Power Switch.


10/12

E-10

XV.Unit Change

Caution:

This function allows the user to select the type of

message that will appear when the replacement

time arrives for each of the different units.


(For details of how to display the Tech. Rep.Mode screen, see the service manual.)

2. Select the Unit Change function as follows:

System Input Unit Change.

3. Select the appropriate message type for each

unit.

4. Touch END.

5. Touch Fin. Time.

XVI.List Output

Caution:

Perform List Output after all adjustments have

been made including those of options.

1. Load the 1st drawer with A4L or Letter L paper.



Mode screen, see the service manual.)3. Select List Output.

4. Select Image Processing.

5. Press the start key.

Then, lists of various kinds will be produced.

6. Touch END.

7. Touch Fin. Time.

XVII.Affixing the Drawer Labels1. Affix the drawer label.

Drawer Label


11/12

E-11

XVIII.Adjusting Registration of Paper

Source Options




2. Select the function to be used as follows:

Machine Adjust PRT Area Left Margin 3rd.

3. Measure width A on the test pattern produced to

check to see if it falls within the specified range.

Specifications: 3.0 1.0 mm

4. If the measured width falls outside the specified

range, adjust with M or L key and then make

the check again.




6. Select the function to be used as follows:

Machine Adjust PRT Area Left Margin

3rd.

* Perform the same adjustment procedure also for

the 4th.

7. Measure width A on the test pattern produced to

check to see if it falls within the specified range.


8. If the measured width falls outside the specified


the check again.

A

A


12/12

E-12




10.Select the function to be used as follows:

Machine Adjust PRT Area Dup. Left Margin

1st.

11.Measure width A on the backside of the test pat-

tern produced to check to see if it falls within the

specified range.


12.If the measured width falls outside the specified


the check again.

13.Perform the same procedure for all paper feed

units.

XIX.Installing the Drawer Cover

1. If a paper source option is mounted, install the

Drawer Cover that comes with the machine using

the Mounting Screws that also come with the

machine.

A

Documents

Konika Installation UnpackC350